Normally the omapdss driver gets the regulators using the regulator
names assigned for omapdss. However, in an effort to get a minimal DSS
support for DT enabled kernel on selected boards, we will add omapdss
devices and platform data the old way even for DT kernel. This causes
the problem that omapdss cannot find the regulators using omapdss's
regulator names.
This patch creates a temporary workaround for DSI and HDMI by trying to
get the regulators also using native OMAP4 regulator names.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This function is now used in the driver init path to handle
probe errors properly. Thus, it may be possible to use this function
outside the exit path.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix sparse warning:
drivers/video/omap2/dss/dispc.c:3320:6: warning: symbol
'dispc_dump_irqs' was not declared. Should it be static?
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
From Michal Simek:
* 'arm-next' of git://git.xilinx.com/linux-xlnx:
zynq: move static peripheral mappings
zynq: remove use of CLKDEV_LOOKUP
zynq: use pl310 device tree bindings
zynq: use GIC device tree bindings
+ Linux 3.7-rc3
Creating the accessory devices, such as audio, from the HDMI driver
allows to regard HDMI as a single entity with audio an display
functionality. This intends to follow the design of drivers such
as MFD, in which a single entity handles the creation of the accessory
devices. Such devices are then used by domain-specific drivers; audio in
this case.
Also, this is in line with the DT implementation of HDMI, in which we will
have a single node to describe this feature of the OMAP SoC.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It could be possible that the DMA port differs accross diferent HDMI IPs. Thus,
add an IP-specific function to obtain the address offset and size of the DMA
data port.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The display must be uninitialized in order to free the requested GPIOs.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Do not blindly assume that the panel could be initialized.
While there, group mutex initialization at a single place.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Do not assume blindly that the DSS driver was registered successfully.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Minor cleanup to give to the resource variable a more proper name.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The return value of wait_for_completion_timeout() is always
>= 0 with unsigned int type.
So the condition "ret < 0" or "ret >= 0" is pointless.
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The return value of wait_for_completion_timeout() is always
>= 0 with unsigned int type.
So the condition "ret < 0" or "ret >= 0" is pointless.
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Merging in Greg's tty tree including a cleanup patch needed by the OMAP serial
header cleanups.
* depends/tty: (305 commits)
tty/serial/8250: Make omap hardware workarounds local to 8250.h
serial/8250/8250_early: Prevent rounding error in uartclk
serial: samsung: use clk_prepare_enable and clk_disable_unprepare
TTY: Report warning when low_latency flag is wrongly used
console: use might_sleep in console_lock
TTY: move tty buffers to tty_port
TTY: add port -> tty link
TTY: tty_buffer, cache pointer to tty->buf
TTY: move TTY_FLUSH* flags to tty_port
TTY: n_tty, propagate n_tty_data
TTY: move ldisc data from tty_struct: locks
TTY: move ldisc data from tty_struct: read_* and echo_* and canon_* stuff
TTY: move ldisc data from tty_struct: bitmaps
TTY: move ldisc data from tty_struct: simple members
TTY: n_tty, add ldisc data to n_tty
TTY: audit, stop accessing tty->icount
TTY: n_tty, remove bogus checks
TTY: n_tty, simplify read_buf+echo_buf allocation
TTY: hci_ldisc, remove invalid check in open
TTY: ldisc, wait for idle ldisc in release
...
check_horiz_timing_omap3() has a variable named 'DS'. i386 uses DS name
for something else, causing a compilation error. As 'DS' is not a very
good local variable name in the first place, let's change it to 'ds',
fixing the issue.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We currently get the decision whether to use PRCM or DSI PLL clock for
DPI from the board file. This is not a good way to handle it, and it
won't work with device tree.
This patch changes DPI to always use DSI PLL if it's available.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The SoCs that have DSI module should have a working DSI PLL. However,
some rare boards have not connected the powers to the DSI PLL.
This patch adds a function that tries to power up the DSI PLL, and
reports if that doesn't succeed. DPI uses this function to fall back to
PRCM clocks if DSI PLL doesn't work.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of using dpi_use_dsi_pll() to check if dsi pll is to be used, we
can just check if dpi.dsidev != NULL.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss.c currently exposes functions to configure the dispc source clock
and lcd source clock. There are configured separately from the output
drivers.
However, there is no safe way for the output drivers to handle dispc
clock, as it's shared between the outputs. Thus, if, say, the DSI driver
sets up DSI PLL and configures both the dispc and lcd clock sources to
that DSI PLL, the resulting dispc clock could be too low for, say, HDMI.
Thus the output drivers should really only be concerned about the lcd
clock, which is what the output drivers actually use. There's lot to do
to clean up the dss clock handling, but this patch takes one step
forward and removes the use of dss_select_dispc_clk_source() from the
output drivers.
After this patch, the output drivers only configure the lcd source
clock. On omap4+ the dispc src clock is never changed from the default
PRCM source. On omap3, where the dispc and lcd clocks are actually the
same, setting the lcd clock source sets the dispc clock source.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We don't currently set the dss fck when starting up. This is not a
problem, as we setup the fck later when configuring the pixel clocks. Or
this is how it was for omap2, for the rest of the omaps this may not be
so.
For DSI, HDMI and also for DPI when using DSI PLL, we don't need to
change the dss fck, and thus it may be left unconfigured. Usually the
dss fck is already setup fine by default, but we can't trust this.
This patch sets the dss fck to maximum at probe time.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss_calc_clock_rates() was removed earlier as it was not used, but it is
needed for DSI PLL calculations, so this patch adds it back.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It looks like on many OMAP versions powers for both HSClk and HSDiv to
be enabled to have a functional HSDiv.
This patch fixes the issue by forcing both powers on.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSI PLL and HSDivider can be used to generate the pixel clock for
LCD overlay manager, which then goes to DPI output. On the DPI output
pin the voltage of the signal is shifted from the OMAP's internal
minimal voltage to 1.8V range. The shifting is not instant, and the
higher the clock frequency, the less time there is to shift the signal
to nominal voltage.
If the HSDivider's divider is greater than one and odd, the resulting
pixel clock does not have 50% duty cycle. For example, with a divider of
3, the duty cycle is 33%.
When combining high frequency (in the area of 140MHz+) and non-50% duty
cycle, it has been observed the the shifter does not have enough time to
shift the voltage enough, and this leads to bad signal which is rejected
by monitors.
As a workaround this patch makes the divider calculation skip all odd
dividers when the required pixel clock is over 100MHz. The limit of
100MHz is a guesstimate.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DPI may use DSI PLL, so it depends on DSI. However, currently DPI driver
is added first, which causes DPI initialization to fail when it tries to
get the DSI PLL.
This patch changes the init order to fix this.
A better solution would be to separate DSI PLL and DSI drivers. They
have dependencies, though, but we could still have DSI PLL as an
independent entity that we could initialize before any of the output
drivers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Backend drivers shouldn't transistion to CLOSED unless the frontend is
CLOSED. If a backend does transition to CLOSED too soon then the
frontend may not see the CLOSING state and will not properly shutdown.
So, treat an unexpected backend CLOSED state the same as CLOSING.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The dispc error handler tries to "fix" issues by disabling and enabling
panel. This is problematic, as we're trying to remove the dependency
from omapdss to the omap_dss_devices. It's also racy, and doesn't really
fix anything.
This patch removes the use of omap_dss_device from the error handler,
and just disables and enables the associated overlay manager. This
should produce similar results as the previous solution, without using
dssdev.
However, the error handling is still horrible. But the problem boils
down to one question, to which I don't have a clear answer: what to do
when a HW error happens?
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The dispc's error handler has a loop inside another loop, and both use
the same loop variable. This is clearly wrong, and this patch makes a
new variable for the inner loop.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The current omapfb code goes over all the modes found from the monitors
EDID data, and searches for a mode that is compatible with the DSS
hardware and has the highest x-res.
While this works ok as such, it proves problematic when using DSI PLL
for pixel clock. Calculating DSI PLL dividers is not the fastest of the
operations, and while doing it for one mode is usually ok, doing it for
20 modes is noticable.
Also, the first mode given in the EDID data should be the native mode of
the monitor, and thus also the best mode, so if that can be used, no
need to look further.
This patch changes the code to use the first mode that is compatible
with the DSS hardware.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It seems that using the second EDID block causes more problems than is
of any help. The first mode in the extended block will get
FB_MODE_IS_FIRST set, which will override the first mode from the first
EDID block, thus making the default videomode selection not to work
properly.
This patch removes the use of the extended edid block for now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The hdmi driver tries to find the given video timings from its static
list of timings, to find the required ID for the mode. The check tries
to find exact match for the pixel clock, among other checks.
with omapfb driver there can be some amount of error in the give pixel
clock, as the pixel clock is converted between Hz and ps, thus the
hdmi's check fails to find the mode.
This patch makes the check more allowing, by rounding the pixel clocks
to nearest MHz.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ricardo Neri <ricardo.neri@ti.com>
This patch makes use of the hdmi_power_[on|off]_core() functions added
in the previous patch. The functions are used when reading EDID or
detecting if a monitor is connected.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ricardo Neri <ricardo.neri@ti.com>
There's currently just one power-on function for HDMI, which enables the
IP and the video output. When reading EDID or detecting if a monitor is
connected, we don't need the video output.
Enabling the video output for these operations is not a big problem in
itself, but the quick enable/disable cycles caused by the operations
seem to cause sync lost errors from time to time. Also, this makes it
possible to read the EDID before the full video path has been set up.
This patch splits the hdmi_power_on into two parts, hdmi_power_on_core
and hdmi_power_on_full. The "full" version does what hdmi_power_on does
currently, and hdmi_power_on_core only enables the core IP. Similar
changes are made for power_off.
Note that these don't allow the HDMI IP to be first enabled, and later
enable the video output, but the HDMI IP will first need to be powered
off before calling the full version. So this is rather limited
implementation, but it fills the needs for reading EDID.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ricardo Neri <ricardo.neri@ti.com>
DISPC irqs need to be handled from the compat layer and also in the
future by the omapdrm. To make this possible, this patchs adds a set of
helper functions, so that the irqs can be managed without direct
register reads/writes.
The following functions are added, and all the current direct reg
reads/writes are changed to use these.
u32 dispc_read_irqstatus(void);
void dispc_clear_irqstatus(u32 mask);
u32 dispc_read_irqenable(void);
void dispc_write_irqenable(u32 mask);
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add new dispc function, dispc_ovl_enabled(). This returns if the overlay
enable bit is set in the registers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We need a low level manager-enable function for omapdrm. We have that
function as dispc internal func, _enable_mgr_out().
This patch exposes that function, and renames it to dispc_mgr_enable().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The current dispc_mgr_enable/disable function are blocking, and do a bit
too much for omapdrm. We'll expose new enable & disable functions that
will just set the bits in the registers in the following patches.
This patch renames the current functions to *_sync, to make it clear
that they are blocking, and also to free up the dispc_mgr_enable/disable
names for these new functions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use dss_feat_get_num_ovls() in dispc.c instead of
omap_dss_get_num_overlays() to remove the dependency to overlay.c. Note
that we still have uses of omap_dss_get_num_overlays() in dispc.c, but
these will be moved out in the future patches.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently omapdss driver sets up the initial connections between
overlays, overlay manager and a panel, based on default display
parameter coming from the board file or via module parameters.
This is unnecessary, as it's the higher level component that should
decide what display to use and how. This patch removes the code from
omapdss, and implements similar code to omapfb.
The def_disp module parameter and the default display platform_data
parameter are kept in omapdss, but omapdss doesn't do anything with
them. It will just return the default display name with
dss_get_default_display_name() call, which omapfb uses. This is done to
keep the backward compatibility.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Export dss_get_def_display_name() with the name of
omapdss_get_def_display_name() so that omapfb can use it after the next
patch which moves default display handling to omapfb.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add the missing unlock on the error handling path in function
hdmi_dump_regs().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit 185bae1095 ("OMAPDSS: DSS: Cleanup
cpu_is_xxxx checks") broke the DSS clocks configuration by erroneously
using the clock parameters applicable to all other OMAP34xx SoCs for the
OMAP363x. This went unnoticed probably because the cpu_is_omap34xx()
class check wasn't seen as matching the OMAP363x subclass.
Fix it by checking for the OMAP363x subclass before checking for the
OMAP34xx class.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add this missing SPI dependency and prevent the driver from building
without SPI, because functions of the spi driver are used in this
driver.
drivers/video/backlight/ili9320.c:51: undefined reference to `spi_sync'
Also, a prompt string for CONFIG_LCD_ILI9320 is added for explicit
selection.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If dsi_get_dsidev_from_id() is called with a DSI module id that does not
exist on the board, the function will crash as omap_dss_get_output()
will return NULL.
This happens on omap3 boards when dumping DSI clocks, as the dumping
code will try to get the dsidev for DSI modules 0 and 1, but omap3 only
has DSI module 0.
Also clean up the id -> output mapping, so that if the function is
called with invalid module ID it will return NULL.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Archit Taneja <archit@ti.com>
window to remove most of the remaining plat includes to get us
closer to ARM common zImage support.
To avoid a huge amount of trivial merge conflicts with includes,
this branch is based on several small topic branches coordinated
with the driver subsystem maintainers. These branches are based on
v3.7-rc1 and can also be merged into the related driver subsystem
branches as needed:
omap-for-v3.8/cleanup-headers-prepare few trivial driver changes
omap-for-v3.8/cleanup-headers-dma move of the DMA header
omap-for-v3.8/cleanup-headers-gpmc GPMC and MTD changes
omap-for-v3.8/cleanup-headers-mmc MMC related changes
omap-for-v3.8/cleanup-headers-dss DSS related changes
omap-for-v3.8/cleanup-headers-asoc ASoC related changes
Note that for the dma-omap.h, it was decided that it should be
is completed. For the related discussion, please see:
https://patchwork.kernel.org/patch/1519591/#
After these patches we still have a few plat headers remaining
that will be handled in later pull requests.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=HUTj
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-headers-signed' into omap-for-v3.8/cleanup-headers-serial-take2
This is the first set of omap cleanup patches for v3.8 merge
window to remove most of the remaining plat includes to get us
closer to ARM common zImage support.
To avoid a huge amount of trivial merge conflicts with includes,
this branch is based on several small topic branches coordinated
with the driver subsystem maintainers. These branches are based on
v3.7-rc1 and can also be merged into the related driver subsystem
branches as needed:
omap-for-v3.8/cleanup-headers-prepare few trivial driver changes
omap-for-v3.8/cleanup-headers-dma move of the DMA header
omap-for-v3.8/cleanup-headers-gpmc GPMC and MTD changes
omap-for-v3.8/cleanup-headers-mmc MMC related changes
omap-for-v3.8/cleanup-headers-dss DSS related changes
omap-for-v3.8/cleanup-headers-asoc ASoC related changes
Note that for the dma-omap.h, it was decided that it should be
is completed. For the related discussion, please see:
https://patchwork.kernel.org/patch/1519591/#
After these patches we still have a few plat headers remaining
that will be handled in later pull requests.
dispc_mgr_lclk_rate() cannot currently be called with DIGIT channel
parameter, even if dispc_ovl_lclk_rate() can. Fix this by making
dispc_mgr_lclk_rate() handle DIGIT channel also.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss.h contains dispc_irq_handler declaration, even if the function is
dispc.c internal. Remove the declaration.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The output drivers get the omapdss hw version from the platform data for
their respective output device. This doesn't work with DT, as there's no
platform data for them.
Add a new function, omapdss_get_version(), which returns the dss version
from the core device, which will have platform data on DT also. The
function is exported so that users of omapdss can also use it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The panel drivers contain enable, disable, suspend and resume calls.
The suspend and resume are effectively identical to disable and enable.
This patch removes panel suspend and enable code from omapdss and the
panel drivers, and replaces their use with enable and disable.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add the missing unlock on the error handling path in function
hdmi_dump_regs().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We currently have a single function to enable and disable the manager
output for LCD and DIGIT. The functions are a bit complex, as handling
both enable and disable require some extra steps to ensure that the
output is enabled or disabled properly without errors before exiting the
function.
The code can be made simpler to understand by splitting the functions
into separate enable and disable functions. We'll also clean up the
comments and some parameter names at the same time.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc.c's functions to enable LCD and DIGIT outputs can be cleaned up a
bit by using common functions to set the enable bit and to check if the
output is enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_ovl_setup() uses struct omap_overlay to get the caps for the
overlay. We can change the code to get the caps directly from dss
features, thus removing the dependency to struct omap_overlay.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss_mgr_set_device and dss_mgr_unset_device are declared in dss.h, but
the functions do not exist. Remove the declarations.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Dispc has a bunch of functions used to configure output related
parameters:
- dispc_mgr_set_io_pad_mode
- dispc_mgr_enable_stallmode
- dispc_mgr_enable_fifohandcheck
- dispc_mgr_set_clock_div
- dispc_mgr_set_tft_data_lines
- dispc_lcd_enable_signal_polarity
- dispc_mgr_set_lcd_type_tft
These are all called together, and the configuration values are taken
from struct dss_lcd_mgr_config.
Instead of exposing those individual dispc functions, create a new one,
dispc_mgr_set_lcd_config(), which is used to configure the above
parameters from values in struct dss_lcd_mgr_config.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When we enable an output we don't check if we need to register the vsync
isr. This causes us to miss vsync interrupts until somebody changes the
configuration of an overlay or an overlay manager.
Add the registration to dss_mgr_enable to fix the problem.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If dsi_get_dsidev_from_id() is called with a DSI module id that does not
exist on the board, the function will crash as omap_dss_get_output()
will return NULL.
This happens on omap3 boards when dumping DSI clocks, as the dumping
code will try to get the dsidev for DSI modules 0 and 1, but omap3 only
has DSI module 0.
Also clean up the id -> output mapping, so that if the function is
called with invalid module ID it will return NULL.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Archit Taneja <archit@ti.com>
There's no need to have this file in plat/fpga.h. We can
make it local to plat-omap replacing fpga_read/write
functions directly with readb/writeb as that's how
they are already defined in fpga.h.
Note that 2420 based H4 is also using the fpga, so let's
keep the led support around in plat-omap until we flip
over mach-omap2 to device tree.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: linux-fbdev@vger.kernel.org
Cc: Felipe Balbi <balbi@ti.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add an exported function omap_vrfb_supported() which returns true if the
vrfb driver has been loaded succesfully. This can be used to decide if
VRFB can be used or not.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that vrfb driver is not omap dependent anymore, we can move vrfb.h
from arch/arm/plat-omap/include/plat to include/video/omapvrfb.h.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
This patch converts vrfb library into a platform device, in an effort to
remove omap dependencies.
The platform device is registered in arch/arm/plat-omap/fb.c and
assigned resources depending on whether running on omap2 or omap3.
The vrfb driver will parse those resources and use them to access vrfb
configuration registers and the vrfb virtual rotation areas.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Now that omapdss no longer uses any platform specific functions, we can
remove the "depends on ARCH_OMAP*" lines from Kconfig.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When compiling on x86 we get following warnings:
warning: field width specifier ‘*’ expects argument of type ‘int’, but
argument 5 has type ‘size_t’ [-Wformat]
Fix these by casting the size_t to int.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When compiling on x86, we get compilation errors for dss.c and dispc.c:
drivers/video/omap2/dss/dispc.c:126:11: error: ‘SZ_4K’ undeclared here
(not in a function)
include <linux/sizes.h> to fix compilation.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Appear to be a copy-paste bug: the code was checking board_data->dsi_enable_pads
while calling board_data->dsi_disable_pads.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move plat/dma.h to plat-omap/dma-omap.h as part of single
zImage work
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It changes the driver to use platform_device_id rather than cpu_is_xxx
to determine the controller type, and updates the platform code
accordingly.
As the result, mach/hardware.h inclusion gets removed from the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: linux-fbdev@vger.kernel.org
The inclusion of mach/hardware.h is not used by the driver at all.
Remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: linux-fbdev@vger.kernel.org
The header ipu.h really belongs to dma subsystem rather than imx
platform. Rename it to ipu-dma.h and put it into include/linux/dma/.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: linux-media@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
All the debug prints have been replaced with pr_debug(). Thus, the dependency on
dss_debug variable is replaced with dyndbg in dynamic debugging mode and DEBUG
flag otherwise. So, the dss_debug variable is removed along with checks for
DEBUG flag.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Reviewed-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The various functions in dispc and dsi such as print_irq_status(),
print_irq_status_vc(), print_irq_status_cio() and _dsi_print_reset_status()
consist of a number of debug prints which need to be enabled all at once or none
at all. So, these debug prints in corresponding functions are replaced with one
dynamic debug enabled pr_debug() each.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Reviewed-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The printk in DSSDBG function definition is replaced with dynamic debug enabled
pr_debug(). The use of dynamic debugging provides more flexibility as each debug
statement can be enabled or disabled dynamically on basis of source filename,
line number, module name etc., by writing to a control file in debugfs
filesystem. For better understanding please refer to
Documentation/dynamic-debug-howto.txt.
The DSSDBGF() differs from DSSDBG() by providing function name. However,
function name, line number, module name and thread ID can be printed through
dynamic debug by setting appropriate flags 'f','l','m' and 't' in the debugfs
control file. So, DSSDBGF instances are replaced with DSSDBG.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Reviewed-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The config option CONFIG_OMAP2_DSS_DEBUG_SUPPORT has been removed and replaced
with CONFIG_OMAP2_DSS_DEBUG and CONFIG_OMAP2_DSS_DEBUGFS. CONFIG_OMAP2_DSS_DEBUG
enables DEBUG flag and CONFIG_OMAP2_DSS_DEBUGFS enables creation of debugfs for
OMAPDSS. Both the config options are disabled by default and can be enabled
independently of one another as per convenience.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Reviewed-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In OMAPDSS the DEBUG flag is set only after the OMAPDSS module is called, for
which the debugging capabilities are available only after its proper
initialization. As a result of which tracking of bugs prior to or during initial
process becomes difficult. So, the definition of DEBUG is being moved to the
corresponding Makefile.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Reviewed-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It includes:
- large updates for OMAP
- basic OMAP5 DSS support for DPI and DSI outputs
- large cleanups and restructuring
- some update to Exynos and da8xx-fb
- removal of the pnx4008 driver (arch removed)
- various other small patches
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=EJUS
-----END PGP SIGNATURE-----
Merge tag 'fbdev-updates-for-3.7' of git://github.com/schandinat/linux-2.6
Pull fbdev updates from Florian Tobias Schandinat:
"This includes:
- large updates for OMAP
- basic OMAP5 DSS support for DPI and DSI outputs
- large cleanups and restructuring
- some update to Exynos and da8xx-fb
- removal of the pnx4008 driver (arch removed)
- various other small patches"
Fix up some trivial conflicts (mostly just include line changes, but
also some due to the renaming of the deferred work functions by Tejun).
* tag 'fbdev-updates-for-3.7' of git://github.com/schandinat/linux-2.6: (193 commits)
gbefb: fix compile error
video: mark nuc900fb_map_video_memory as __devinit
video/mx3fb: set .owner to prevent module unloading while being used
video: exynos_dp: use clk_prepare_enable and clk_disable_unprepare
drivers/video/exynos/exynos_mipi_dsi.c: fix error return code
drivers/video/savage/savagefb_driver.c: fix error return code
video: s3c-fb: use clk_prepare_enable and clk_disable_unprepare
da8xx-fb: save and restore LCDC context across suspend/resume cycle
da8xx-fb: add pm_runtime support
video/udlfb: fix line counting in fb_write
OMAPDSS: add missing include for string.h
OMAPDSS: DISPC: Configure color conversion coefficients for writeback
OMAPDSS: DISPC: Add manager like functions for writeback
OMAPDSS: DISPC: Configure writeback FIFOs
OMAPDSS: DISPC: Configure writeback specific parameters in dispc_wb_setup()
OMAPDSS: DISPC: Configure overlay-like parameters in dispc_wb_setup
OMAPDSS: DISPC: Add function to set channel in for writeback
OMAPDSS: DISPC: Don't set chroma resampling bit for writeback
OMAPDSS: DISPC: Downscale chroma if plane is writeback
OMAPDSS: DISPC: Configure input and output sizes for writeback
...
The patch "drivers/video/gbefb.c: use devm_ functions" caused a
compile error.
drivers/video/gbefb.c:1159:16: error: implicit declaration of function
'devm_ioremap' [-Werror=implicit-function-declaration]
drivers/video/gbefb.c:1179:3: error: implicit declaration of function
'devm_ioremap_nocache' [-Werror=implicit-function-declaration]
Fix it by including linux/io.h which defines those functions.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Damien Cassou <damien.cassou@lifl.fr>
All legacy PWM providers have now been moved to the PWM subsystem. The
plan for 3.8 is to adapt all board files to provide a lookup table for
PWM devices in order to get rid of the global namespace. Subsequently,
users of the legacy pwm_request() and pwm_free() functions can be
migrated to the new pwm_get() and pwm_put() functions. Once this has
been completed, the legacy API and the compatibility code in the core
can be removed.
In addition to the above, these changes also add support for configuring
the polarity of a PWM signal (currently only supported on ECAP and
EHRPWM) and include a much needed rework of the i.MX driver. Managed
functions to obtain and release a PWM device (devm_pwm_get() and
devm_pwm_put()) have been added and the pwm-backlight driver has been
updated to use them. If the PWM subsystem hasn't been enabled, dummy
functions are provided that allow the subsystem to safely compile out.
Some common checks on input parameters have been moved to the core and
removed from the drivers. Finally, a small fix corrects the description
of the PWM specifier's second cell in the device tree representation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJQcV6pAAoJEN0jrNd/PrOh594P/3NHPjnTiyAZpUICX4mJeoMd
1rX685HofCyX5jlHloS1pLRXYtIPZP97We5crNR/k/RujKcHAqAFzLtG2Jj93gxm
nRUwLZ4xbrAgeaZeJV8YG1naWx9R1OjrK2sv+FyHRWsn9UZus2vDMV7tB0oNWo9k
DMhtF1q7gQxx4nRu8z9FFybyItQinVREODNs+Gdv6AOJ36t+mOsGPL3LKZeFsIG3
LdaB1p3t/07Job4KwGYYRjkOR7bIQ+ADnnO8Pkk0a9lxkMI8rA0uFbLwgyx7Hohh
xZtm8R5il2IlHwqh52RzpShceWICxCZ3htuIXTRbVa1PSEsBzZ66W2CT7sy1jPm5
lJlHgc7abaiwijtoG76I+Lgslv5UTViBuIYHSX4dH2kF3Jgm2SgTBNzZYePI5MMT
BI3xc9WnwBpxgMybJsPHfU0Ff6O/9h9ab7q5lBOHkQJittahYxzWD+FgYlalcAa+
I919iFREKNZytewLnXu+4TG0RfacQoj6D5G+SquOGmXyKYRhhJ1O6WodnRZHi/0n
M6J0f6fLxpomI1RMn44VYP43OPJCDYxgXYoDLwCZQL9tSWYpdhXoDrjcIPO547w1
ZS5HTXUE4DrxeYjoeqL555vtQIooM9CuH4JwKlz5zzea8NPC8eVtmNFTTWE6wKWX
ZIOOLVvw/FI0/DSjBb8H
=MQ5V
-----END PGP SIGNATURE-----
Merge tag 'for-3.7-rc1' of git://gitorious.org/linux-pwm/linux-pwm
Pull pwm changes from Thierry Reding:
"All legacy PWM providers have now been moved to the PWM subsystem.
The plan for 3.8 is to adapt all board files to provide a lookup table
for PWM devices in order to get rid of the global namespace.
Subsequently, users of the legacy pwm_request() and pwm_free()
functions can be migrated to the new pwm_get() and pwm_put()
functions. Once this has been completed, the legacy API and the
compatibility code in the core can be removed.
In addition to the above, these changes also add support for
configuring the polarity of a PWM signal (currently only supported on
ECAP and EHRPWM) and include a much needed rework of the i.MX driver.
Managed functions to obtain and release a PWM device (devm_pwm_get()
and devm_pwm_put()) have been added and the pwm-backlight driver has
been updated to use them. If the PWM subsystem hasn't been enabled,
dummy functions are provided that allow the subsystem to safely
compile out.
Some common checks on input parameters have been moved to the core and
removed from the drivers. Finally, a small fix corrects the
description of the PWM specifier's second cell in the device tree
representation."
* tag 'for-3.7-rc1' of git://gitorious.org/linux-pwm/linux-pwm: (23 commits)
pwm: dt: Fix description of second PWM cell
pwm: Check for negative duty-cycle and period
pwm: Add Ingenic JZ4740 support
MIPS: JZ4740: Export timer API
pwm: Move PUV3 PWM driver to PWM framework
unicore32: pwm: Use managed resource allocations
unicore32: pwm: Remove unnecessary indirection
unicore32: pwm: Use module_platform_driver()
unicore32: pwm: Properly remap memory-mapped registers
pwm-backlight: Use devm_pwm_get() instead of pwm_get()
pwm: Move AB8500 PWM driver to PWM framework
pwm: Fix compilation error when CONFIG_PWM is not defined
pwm: i.MX: fix clock lookup
pwm: i.MX: use per clock unconditionally
pwm: i.MX: add devicetree support
pwm: i.MX: Use module_platform_driver
pwm: i.MX: add functions to enable/disable pwm.
pwm: i.MX: remove unnecessary if in pwm_[en|dis]able
pwm: i.MX: factor out SoC specific functions
pwm: pwm-tiehrpwm: Add support for configuring polarity of PWM
...
Notable changes:
* Basic writeback support for DISPC level. Writeback is not yet usable, though,
as we need higher level code to actually expose the writeback feature to
userspace.
* Rewriting the omapdss output drivers. We're trying to remove the hard links
between the omapdss and the panels, and this rewrite work moves us closer to
that goal.
* Cleanup and restructuring patches that have been made while working on device
tree support for omapdss. Device tree support is still some way ahead, but
these patches are good cleanups in themselves.
* Basic OMAP5 DSS support for DPI and DSI outputs.
* Workaround for the problem that GFX overlay's fifo is too small for high
resolution scenarios, causing underflows.
* Cleanups that remove dependencies to omap platform code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=lcyJ
-----END PGP SIGNATURE-----
Merge tag 'omapdss-for-3.7' of git://gitorious.org/linux-omap-dss2/linux into fbdev-next
Omapdss driver changes for the 3.7 merge window.
Notable changes:
* Basic writeback support for DISPC level. Writeback is not yet usable, though,
as we need higher level code to actually expose the writeback feature to
userspace.
* Rewriting the omapdss output drivers. We're trying to remove the hard links
between the omapdss and the panels, and this rewrite work moves us closer to
that goal.
* Cleanup and restructuring patches that have been made while working on device
tree support for omapdss. Device tree support is still some way ahead, but
these patches are good cleanups in themselves.
* Basic OMAP5 DSS support for DPI and DSI outputs.
* Workaround for the problem that GFX overlay's fifo is too small for high
resolution scenarios, causing underflows.
* Cleanups that remove dependencies to omap platform code.
nuc900fb_map_video_memory is called by an devinit function
that may be called at run-time, but the function itself is
marked __init and will be discarded after boot.
To avoid calling into a function that may have been overwritten,
mark nuc900fb_map_video_memory itself as __devinit.
Without this patch, building nuc950_defconfig results in:
WARNING: drivers/video/built-in.o(.devinit.text+0x26c): Section mismatch in reference from the function nuc900fb_probe() to the function .init.text:nuc900fb_map_video_memory()
The function __devinit nuc900fb_probe() references
a function __init nuc900fb_map_video_memory().
If nuc900fb_map_video_memory is only used by nuc900fb_probe then
annotate nuc900fb_map_video_memory with a matching annotation.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Save and restore register context of LCDC respectively
before suspend and after resume.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Line 0 and 1 were both written to line 0 (on the display) and all subsequent
lines had an offset of -1. The result was that the last line on the display
was never overwritten by writes to /dev/fbN.
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Acked-by: Bernie Thompson <bernie@plugable.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
A long time ago, in v2.4, VM_RESERVED kept swapout process off VMA,
currently it lost original meaning but still has some effects:
| effect | alternative flags
-+------------------------+---------------------------------------------
1| account as reserved_vm | VM_IO
2| skip in core dump | VM_IO, VM_DONTDUMP
3| do not merge or expand | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
4| do not mlock | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
This patch removes reserved_vm counter from mm_struct. Seems like nobody
cares about it, it does not exported into userspace directly, it only
reduces total_vm showed in proc.
Thus VM_RESERVED can be replaced with VM_IO or pair VM_DONTEXPAND | VM_DONTDUMP.
remap_pfn_range() and io_remap_pfn_range() set VM_IO|VM_DONTEXPAND|VM_DONTDUMP.
remap_vmalloc_range() set VM_DONTEXPAND | VM_DONTDUMP.
[akpm@linux-foundation.org: drivers/vfio/pci/vfio_pci.c fixup]
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Venkatesh Pallipadi <venki@google.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Managed versions of the pwm_get() and pwm_put() functions were recently
added to the PWM framework. They can be used to simplify cleanup in the
error paths and the device removal callback.
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Pull powerpc updates from Benjamin Herrenschmidt:
"Some highlights in addition to the usual batch of fixes:
- 64TB address space support for 64-bit processes by Aneesh Kumar
- Gavin Shan did a major cleanup & re-organization of our EEH support
code (IBM fancy PCI error handling & recovery infrastructure) which
paves the way for supporting different platform backends, along
with some rework of the PCIe code for the PowerNV platform in order
to remove home made resource allocations and instead use the
generic code (which is possible after some small improvements to it
done by Gavin).
- Uprobes support by Ananth N Mavinakayanahalli
- A pile of embedded updates from Freescale folks, including new SoC
and board supports, more KVM stuff including preparing for 64-bit
BookE KVM support, ePAPR 1.1 updates, etc..."
Fixup trivial conflicts in drivers/scsi/ipr.c
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc/iommu: Fix multiple issues with IOMMU pools code
powerpc: Fix VMX fix for memcpy case
driver/mtd:IFC NAND:Initialise internal SRAM before any write
powerpc/fsl-pci: use 'Header Type' to identify PCIE mode
powerpc/eeh: Don't release eeh_mutex in eeh_phb_pe_get
powerpc: Remove tlb batching hack for nighthawk
powerpc: Set paca->data_offset = 0 for boot cpu
powerpc/perf: Sample only if SIAR-Valid bit is set in P7+
powerpc/fsl-pci: fix warning when CONFIG_SWIOTLB is disabled
powerpc/mpc85xx: Update interrupt handling for IFC controller
powerpc/85xx: Enable USB support in p1023rds_defconfig
powerpc/smp: Do not disable IPI interrupts during suspend
powerpc/eeh: Fix crash on converting OF node to edev
powerpc/eeh: Lock module while handling EEH event
powerpc/kprobe: Don't emulate store when kprobe stwu r1
powerpc/kprobe: Complete kprobe and migrate exception frame
powerpc/kprobe: Introduce a new thread flag
powerpc: Remove unused __get_user64() and __put_user64()
powerpc/eeh: Global mutex to protect PE tree
powerpc/eeh: Remove EEH PE for normal PCI hotplug
...
Merge misc patches from Andrew Morton:
"The MM tree is rather stuck while I wait to find out what the heck is
happening with sched/numa. Probably I'll need to route around all the
code which was added to -next, sigh.
So this is "everything else", or at least most of it - other small
bits are still awaiting resolutions of various kinds."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (180 commits)
lib/decompress.c add __init to decompress_method and data
kernel/resource.c: fix stack overflow in __reserve_region_with_split()
omfs: convert to use beXX_add_cpu()
taskstats: cgroupstats_user_cmd() may leak on error
aoe: update aoe-internal version number to 50
aoe: update documentation to better reflect aoe-plus-udev usage
aoe: remove unused code
aoe: make dynamic block minor numbers the default
aoe: update and specify AoE address guards and error messages
aoe: retain static block device numbers for backwards compatibility
aoe: support more AoE addresses with dynamic block device minor numbers
aoe: update documentation with new URL and VM settings reference
aoe: update copyright year in touched files
aoe: update internal version number to 49
aoe: remove unused code and add cosmetic improvements
aoe: increase net_device reference count while using it
aoe: associate frames with the AoE storage target
aoe: disallow unsupported AoE minor addresses
aoe: do revalidation steps in order
aoe: failover remote interface based on aoe_deadsecs parameter
...
This patch adds the of_match_table to platform-lcd driver to be
probed when platform-lcd device node is found in the device tree.
[akpm@linux-foundation.org: include of.h]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
devm_kfree should not have to be explicitly used.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,d;
@@
x = devm_kzalloc(...)
...
?-devm_kfree(d,x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver was for the ProGear webpad device which was produced in
2000/2001 and is not available on a market. I no longer have this
hardware so can not even check how Linux works on it.
Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver is a general version for LM3639 backlgiht + flash driver chip
of TI.
LM3639:
The LM3639 is a single chip LCD Display Backlight driver + white LED
Camera driver. Programming is done over an I2C compatible interface.
www.ti.com
[akpm@linux-foundation.org: code layout tweaks]
Signed-off-by: G.Shark Jeong <gshark.jeong@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Daniel Jeong <daniel.jeong@ti.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver is a general version for LM3630 backlgiht driver chip of TI.
LM3630 :
The LM3630 is a current mode boost converter which supplies the power
and controls the current in two strings of up to 10 LEDs per string.
Programming is done over an I2C compatible interface.
www.ti.com
[akpm@linux-foundation.org: make bled_name[] static, a few coding style tuneups, create new set_intensity(), partly to avoid awkward layout gymnastics]
Signed-off-by: G.Shark Jeong <gshark.jeong@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Daniel Jeong <daniel.jeong@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since msleep() might not sleep for the desired amount when less than 20ms,
use usleep_range().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Claudio Nieder <private@claudio.ch>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since msleep() might not sleep for the desired amount when less than 20ms,
use usleep_range().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since msleep() might not sleep for the desired amount when less than 20ms,
use usleep_range().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Ashish Jangam <ashish.jangam@kpitcummins.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x, palmas,
ab8500, wm8994, wm5110, max8907 and the tps65xxx family.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=n6lp
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"MFD bits for the 3.7 merge window.
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x,
palmas, ab8500, wm8994, wm5110, max8907 and the tps65xxx family."
Fix up various annoying conflicts: the DT and IRQ domain support came in
twice and was already in 3.6. And then it was apparently rebased.
Guys, DON'T REBASE!
* tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (89 commits)
ARM: dts: Enable 88pm860x pmic
mfd: 88pm860x: Move gpadc init into touch
mfd: 88pm860x: Device tree support
mfd: 88pm860x: Use irqdomain
mfd: smsc: Add support for smsc gpio io/keypad driver
backlight: tps65217_bl: Add missing platform_set_drvdata in tps65217_bl_probe
mfd: DA9055 core driver
mfd: tps65910: Add alarm interrupt of TPS65910 RTC to mfd device list
mfd: wm5110: Add register patches for revision B
mfd: wm5110: Disable control interface error report for WM5110 rev B
mfd: max8907: Remove regulator-compatible from DT docs
backlight: Add TPS65217 WLED driver
mfd: Add backlight as subdevice to the tps65217
mfd: Provide the PRCMU with its own IRQ domain
mfd: Fix max8907 sparse warning
mfd: Add lp8788 mfd driver
mfd: dbx500: Provide a more accurate smp_twd clock
mfd: rc5t583: Fix warning messages
regulator: palmas: Add DT support
mfd: palmas: Change regulator defns to better suite DT
...
Pull vfs update from Al Viro:
- big one - consolidation of descriptor-related logics; almost all of
that is moved to fs/file.c
(BTW, I'm seriously tempted to rename the result to fd.c. As it is,
we have a situation when file_table.c is about handling of struct
file and file.c is about handling of descriptor tables; the reasons
are historical - file_table.c used to be about a static array of
struct file we used to have way back).
A lot of stray ends got cleaned up and converted to saner primitives,
disgusting mess in android/binder.c is still disgusting, but at least
doesn't poke so much in descriptor table guts anymore. A bunch of
relatively minor races got fixed in process, plus an ext4 struct file
leak.
- related thing - fget_light() partially unuglified; see fdget() in
there (and yes, it generates the code as good as we used to have).
- also related - bits of Cyrill's procfs stuff that got entangled into
that work; _not_ all of it, just the initial move to fs/proc/fd.c and
switch of fdinfo to seq_file.
- Alex's fs/coredump.c spiltoff - the same story, had been easier to
take that commit than mess with conflicts. The rest is a separate
pile, this was just a mechanical code movement.
- a few misc patches all over the place. Not all for this cycle,
there'll be more (and quite a few currently sit in akpm's tree)."
Fix up trivial conflicts in the android binder driver, and some fairly
simple conflicts due to two different changes to the sock_alloc_file()
interface ("take descriptor handling from sock_alloc_file() to callers"
vs "net: Providing protocol type via system.sockprotoname xattr of
/proc/PID/fd entries" adding a dentry name to the socket)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (72 commits)
MAX_LFS_FILESIZE should be a loff_t
compat: fs: Generic compat_sys_sendfile implementation
fs: push rcu_barrier() from deactivate_locked_super() to filesystems
btrfs: reada_extent doesn't need kref for refcount
coredump: move core dump functionality into its own file
coredump: prevent double-free on an error path in core dumper
usb/gadget: fix misannotations
fcntl: fix misannotations
ceph: don't abuse d_delete() on failure exits
hypfs: ->d_parent is never NULL or negative
vfs: delete surplus inode NULL check
switch simple cases of fget_light to fdget
new helpers: fdget()/fdput()
switch o2hb_region_dev_write() to fget_light()
proc_map_files_readdir(): don't bother with grabbing files
make get_file() return its argument
vhost_set_vring(): turn pollstart/pollstop into bool
switch prctl_set_mm_exe_file() to fget_light()
switch xfs_find_handle() to fget_light()
switch xfs_swapext() to fget_light()
...
Pull workqueue changes from Tejun Heo:
"This is workqueue updates for v3.7-rc1. A lot of activities this
round including considerable API and behavior cleanups.
* delayed_work combines a timer and a work item. The handling of the
timer part has always been a bit clunky leading to confusing
cancelation API with weird corner-case behaviors. delayed_work is
updated to use new IRQ safe timer and cancelation now works as
expected.
* Another deficiency of delayed_work was lack of the counterpart of
mod_timer() which led to cancel+queue combinations or open-coded
timer+work usages. mod_delayed_work[_on]() are added.
These two delayed_work changes make delayed_work provide interface
and behave like timer which is executed with process context.
* A work item could be executed concurrently on multiple CPUs, which
is rather unintuitive and made flush_work() behavior confusing and
half-broken under certain circumstances. This problem doesn't
exist for non-reentrant workqueues. While non-reentrancy check
isn't free, the overhead is incurred only when a work item bounces
across different CPUs and even in simulated pathological scenario
the overhead isn't too high.
All workqueues are made non-reentrant. This removes the
distinction between flush_[delayed_]work() and
flush_[delayed_]_work_sync(). The former is now as strong as the
latter and the specified work item is guaranteed to have finished
execution of any previous queueing on return.
* In addition to the various bug fixes, Lai redid and simplified CPU
hotplug handling significantly.
* Joonsoo introduced system_highpri_wq and used it during CPU
hotplug.
There are two merge commits - one to pull in IRQ safe timer from
tip/timers/core and the other to pull in CPU hotplug fixes from
wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."
Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.
Tejun pointed out a few of them, I fixed a couple more.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
workqueue: remove @delayed from cwq_dec_nr_in_flight()
workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
workqueue: use __cpuinit instead of __devinit for cpu callbacks
workqueue: rename manager_mutex to assoc_mutex
workqueue: WORKER_REBIND is no longer necessary for idle rebinding
workqueue: WORKER_REBIND is no longer necessary for busy rebinding
workqueue: reimplement idle worker rebinding
workqueue: deprecate __cancel_delayed_work()
workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
workqueue: use mod_delayed_work() instead of __cancel + queue
workqueue: use irqsafe timer for delayed_work
workqueue: clean up delayed_work initializers and add missing one
workqueue: make deferrable delayed_work initializer names consistent
workqueue: cosmetic whitespace updates for macro definitions
workqueue: deprecate system_nrt[_freezable]_wq
workqueue: deprecate flush[_delayed]_work_sync()
...
This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot of
driver/platform shared definitions have gone, such as platform data
structures. They now need to move out to a common location instead,
and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move and
once it settles in, we should be good for quite a while. Sorry for the
overhead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Tc6y
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
A shorter cleanup branch submitted separately due to dependencies with
some of the previous topics.
Major thing here is that the Broadcom bcmring platform is removed. It's an
SoC that's used on some stationary VoIP platforms, and is in desperate
need of some cleanup. Broadcom came back and suggested that we just
deprecate the platform for now, since they aren't going to spend the
resources needed on cleaning it up, and there are no users of the platform
directly from mainline.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=LPF/
-----END PGP SIGNATURE-----
Merge tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc cleanups, part 2 from Olof Johansson:
"A shorter cleanup branch submitted separately due to dependencies with
some of the previous topics.
Major thing here is that the Broadcom bcmring platform is removed.
It's an SoC that's used on some stationary VoIP platforms, and is in
desperate need of some cleanup. Broadcom came back and suggested that
we just deprecate the platform for now, since they aren't going to
spend the resources needed on cleaning it up, and there are no users
of the platform directly from mainline."
Fix some conflicts due to BCM2835 getting added next to the removed
BCMRING, and removal of tegra files that had been converted to
devicetree.
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: Orion5x: ts78xx: Add IOMEM for virtual addresses.
ARM: ux500: use __iomem pointers for MMIO
ARM: Remove mach-bcmring
ARM: clps711x: Remove board support for CEIVA
ARM: clps711x: Fix register definitions
ARM: clps711x: Fix lowlevel debug-macro
ARM: clps711x: Added simple clock framework
pinctrl: tegra: move pinconf-tegra.h content into drivers/pinctrl
ARM: tegra: delete unused headers
ARM: tegra: remove useless includes of <mach/*.h>
ARM: tegra: remove dead code
Device tree conversion and enablement branch. Mostly a bunch of new
bindings and setup for various platforms, but the Via/Winchip VT8500
platform is also converted over from being 100% legacy to now use
device tree for probing. More of that will come for 3.8.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=q7ZY
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc device tree updates from Olof Johansson:
"Device tree conversion and enablement branch. Mostly a bunch of new
bindings and setup for various platforms, but the Via/Winchip VT8500
platform is also converted over from being 100% legacy to now use
device tree for probing. More of that will come for 3.8."
Trivial conflicts due to removal of vt8500 files, and one documentation
file that was added with slightly different contents both here and in
the USb tree.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (212 commits)
arm: vt8500: Fixup for missing gpio.h
ARM: LPC32xx: LED fix in PHY3250 DTS file
ARM: dt: mmp-dma: add binding file
arm: vt8500: Update arch-vt8500 to devicetree support.
arm: vt8500: gpio: Devicetree support for arch-vt8500
arm: vt8500: doc: Add device tree bindings for arch-vt8500 devices
arm: vt8500: clk: Add Common Clock Framework support
video: vt8500: Add devicetree support for vt8500-fb and wm8505-fb
serial: vt8500: Add devicetree support for vt8500-serial
rtc: vt8500: Add devicetree support for vt8500-rtc
arm: vt8500: Add device tree files for VIA/Wondermedia SoC's
ARM: tegra: Add Avionic Design Tamonten Evaluation Carrier support
ARM: tegra: Add Avionic Design Medcom-Wide support
ARM: tegra: Add Avionic Design Plutux support
ARM: tegra: Add Avionic Design Tamonten support
ARM: tegra: dts: Add pwm label
ARM: ux500: Fix SSP register address format
ARM: ux500: Apply tc3589x's GPIO/IRQ properties to HREF's DT
ARM: ux500: Remove redundant #gpio-cell properties from Snowball DT
ARM: ux500: Add all encompassing sound node to the HREF Device Tree
...
This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used with
a mainline kernel. We have not been able to find anyone interested
in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ck1u
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc general cleanups from Olof Johansson:
"This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used
with a mainline kernel. We have not been able to find anyone
interested in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above."
Fix up some conflicts with the staging tree (and because nxp4008 was
removed)
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (184 commits)
ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6
ARM: OMAP4: twl-common: Support for additional devices on i2c1 bus
ARM: mmp: using for_each_set_bit to simplify the code
ARM: tegra: harmony: fix ldo7 regulator-name
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
...
Pull x86/EFI changes from Ingo Molnar:
"EFI loader robustness enhancements plus smaller fixes"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: Fix the ACPI BGRT driver for images located in EFI boot services memory
efi: Add a function to look up existing IO memory mappings
efi: Defer freeing boot services memory until after ACPI init
x86, EFI: Calculate the EFI framebuffer size instead of trusting the firmware
efifb: Skip DMI checks if the bootloader knows what it's doing
efi: initialize efi.runtime_version to make query_variable_info/update_capsule workable
efi: Build EFI stub with EFI-appropriate options
X86: Improve GOP detection in the EFI boot stub
Pull the trivial tree from Jiri Kosina:
"Tiny usual fixes all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
doc: fix old config name of kprobetrace
fs/fs-writeback.c: cleanup riteback_sb_inodes kerneldoc
btrfs: fix the commment for the action flags in delayed-ref.h
btrfs: fix trivial typo for the comment of BTRFS_FREE_INO_OBJECTID
vfs: fix kerneldoc for generic_fh_to_parent()
treewide: fix comment/printk/variable typos
ipr: fix small coding style issues
doc: fix broken utf8 encoding
nfs: comment fix
platform/x86: fix asus_laptop.wled_type module parameter
mfd: printk/comment fixes
doc: getdelays.c: remember to close() socket on error in create_nl_socket()
doc: aliasing-test: close fd on write error
mmc: fix comment typos
dma: fix comments
spi: fix comment/printk typos in spi
Coccinelle: fix typo in memdup_user.cocci
tmiofb: missing NULL pointer checks
tools: perf: Fix typo in tools/perf
tools/testing: fix comment / output typos
...
Otherwise, we got NULL derefernce while calling backlight_device_unregister()
in tps65217_bl_remove().
Also convert to use module_platform_driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* cleanup/__iomem:
ARM: Orion5x: ts78xx: Add IOMEM for virtual addresses.
ARM: ux500: use __iomem pointers for MMIO
Two new cleanup patches that were not already part of the
first cleanup branch.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The current kernel does not fit in the CEIVA ROM. Also, some functional
has already been removed due migrate from 2.6 to 3.0, and it seems that
no one uses this platform. So, remove support for this board and modules
specific only to this board.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Both dpi.c and sdi.c use strcmp(), but do not include string.h. With
some Kconfig options string.h is included implicitly, but with some
other the compilation fails:
drivers/video/omap2/dss/dpi.c:407:5: error: implicit declaration of
function 'strcmp'
Include string.h in both dpi.c and sdi.c
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Writeback pipeline receives RGB data from one of the overlays or one of the
overlay managers. If the target color mode is YUV422 or NV12, we need to convert
the RGB pixels to YUV. The scaler in WB then converts it to the target color
mode.
Hence, the color conversion coefficients that need to be programmed are the ones
which convert a RGB24 pixel to YUV444. Program these coefficients for writeback
pipeline.
Rearrange the code a bit to configure different coefficients for overlays and
writeback.
Signed-off-by: Archit Taneja <archit@ti.com>
Add functions to enable writeback, and set/check state of GO bit. These bits are
identical in behaviour with the corresponding overlay manager bits. Configure
them in a similar way to mgr_enable() and mgr_go_* functions. Add a helper to
get the FRAMEDONE irq corresponding to writeback.
Signed-off-by: Archit Taneja <archit@ti.com>
Extend the DISPC fifo functions to also configure the writeback FIFO thresholds.
The most optimal configuration for writeback is to push out data to the
interconnect the moment writeback pushes enough pixels in the FIFO to form a
burst. This reduces the chance of writeback overflowing it's FIFO.
Signed-off-by: Archit Taneja <archit@ti.com>
Configure some of the writeback specific parameters in dispc_wb_setup(). The
writeback parameters configured are:
truncation: This needs to be set if the color depth input to writeback is more
than the color depth of the color mode we want to store in memory.
writeback mode: This configures whether we want to use writeback in mem to mem
or capture mode. This information will be directly passed by APPLY later.
Signed-off-by: Archit Taneja <archit@ti.com>
Create struct omap_dss_writeback_info, this is similar to omap_overlay_info,
the major difference is that there is no parameter which describes the input
size to writeback, this is because this is always fixed, and decided by the
connected overlay or overlay manager. One more difference is that screen_width
is renamed to buf_width, to give the value of stride the writeback buffer has.
Call dispc_ovl_setup_common() through dispc_wb_setup() to configure overlay-like
parameters. The parameters in dispc_ovl_setup_common() which do not hold for
writeback are filled passed as zeroes or false, the code takes care of not
configuring them as they won't possess the needed overlay caps.
Signed-off-by: Archit Taneja <archit@ti.com>
Writeback can take input from either one of the overlays, or one of the overlay
managers. Add an enum which represents the channel_in for writeback, and maps
to the register field programming.
Add a function to configure channel in for writeback. This will be used later in
APPLY.
Signed-off-by: Archit Taneja <archit@ti.com>
The bit YUVCHROMARESAMPLING isn't there for writeback in DISPC_WB_ATTRIBUTES2.
It isn't there because we don't upsample chroma like for video pipelines, we
downsample chroma in writeback to get YUV422 or NV12 formats from the YUV444
input.
Ignore this bit in dispc_ovl_set_scaling_uv() if the plane is OMAP_DSS_WB.
Signed-off-by: Archit Taneja <archit@ti.com>
When converting YUYV444 content to YUV422 or NV12 formats through writeback
pipeline, the scaler needs to downscale the chroma plane. Ensure that chroma
is downscaled when the pipeline is writeback.
Signed-off-by: Archit Taneja <archit@ti.com>
Writeback uses the WB_PICTURE_SIZE register to define the size of the content
written to memory, this is the output of the scaler. It uses the WB_SIZE
register to define the size of the content coming from the overlay/manager to
which it is connected, this is the input to the scaler. This naming is different
as compared to overlays.
Add checks for writeback in dispc_ovl_set_input_size() and
dispc_ovl_set_output_size() to write to the correct registers.
Signed-off-by: Archit Taneja <archit@ti.com>
Since writeback has many overlay like properties, and most of it's registers are
similar to that of overlays, it's possible to reuse most of the overlay related
DISPC code for writeback when considering it as a plane. Writeback was added as
a plane in the omap_plane field as OMAP_DSS_WB.
Add the writeback register offsets in dispc.h, add minimal WB plane related info
needed in dss_features. Add a function which returns the number of writeback
pipelines an OMAP version has.
Signed-off-by: Archit Taneja <archit@ti.com>
In the function dispc_plane_set_scaling_uv(), create a parameter which tells if
we want to upscale or downscale the chroma plane.
Downscaling of chroma is required by writeback pipeline for converting the input
YUV444 color format to YUV422 or NV12.
Signed-off-by: Archit Taneja <archit@ti.com>
The scalers of overlays and writeback do not have any constraints on downscale
ratio when operating in memory to memory mode.
This is because in memory to memory mode, we aren't connected to a display which
needs data output at the rate of pixel clock. The scalers can perform as much
downscaling as needed, the rate at which the scaler outputs is adjusted
accordingly.
Relax constraints related to downscaling based on whether the input overlays are
connected to writeback in memory to memory mode. We pass a mem_to_mem boolean
parameter to dispc_ovl_setup() from APPLY. This is currently set to false, this
will later be configured to the correct value based on whether the overlay is
connected to writeback or not. Do the same later for writeback when writeback is
configured.
In the scaling calculation code, we calculate the minimum amount of core clock we
need to achieve the required downscaling. If we are in memory to memory mode, we
set this to a very small value(1 in this case), this value would always be
lesser than the actual DISPC core clock value, and hence the scaling checks
would succeed.
We take care that pixel clock isn't calculated for writeback and the overlays
connected to it when in memory to memory mode. A pixel clock in such cases
doesn't make sense.
Signed-off-by: Archit Taneja <archit@ti.com>
dispc_ovl_setup_common() is to be used by both overlays and writeback. We pass
channel out to figure out what manager the overlay is connected to, to determine
the pixel clock rate. This is used to decide the scaling limitations for that
overlay.
writeback doesn't have a channel out, it has a channel in field which tells
where writeback gets its input from. These are 2 different fields, and this
prevents us reusing the overlay configuration code for writeback.
To overcome this, we now pass omap_plane to overlay related functions rather
than passing channel out. We create helper functions which can derive pclk/lclk
from the omap_plane id.
Signed-off-by: Archit Taneja <archit@ti.com>
Add a new static function called dispc_ovl_setup_common(). This function is used by
dispc_ovl_setup() to configure the overlay registers. This split is done so that
dispc_wb_setup() can reuse overlay register configuration related code.
Signed-off-by: Archit Taneja <archit@ti.com>
Add position and replication as overlay caps, and pass overlay caps as an
argument to the corresponding functions. Adding position and replication to
overlay caps seems a bit unnecessary, but it allows us to use the
corresponding functions for writeback too.
These caps will be set for all overlays, but not for writeback. This is done
so writeback can reuse dispc_ovl_setup() to the maximum.
Signed-off-by: Archit Taneja <archit@ti.com>
Currently, the functions below take the omap_plane parameter and derive the
overlay caps within them. Pass the overlay caps as a parameter to the function
to allow these to be used by writeback too.
- dispc_ovl_set_zorder()
- dispc_ovl_set_pre_mult_alpha()
- dispc_ovl_setup_global_alpha()
- dispc_ovl_calc_scaling()
- dispc_ovl_setup()
These functions will be used for writeback later, and the caps will help in
deciding if they are to be used for writeback or not. This allows reuse of
overlay caps for writeback.
Using omap_overlay_caps for writeback seems a bit incorrect, but caps is
something already in use by users of OMAPDSS(omapfb/omap_vout), so we use
overlay caps for overlay like features of writeback too.
Signed-off-by: Archit Taneja <archit@ti.com>
The DISPC pipeline register names in the TRM for setting the buffer size and
the output size are a bit misleading, for example, there are different register
names for setting the buffer size for VID and GFX pipes. Things get more
confusing when considering writeback pipeline.
Rename the functions so that they tell whether they are configuring the input
to the scalar or the output. These will be extended later to support writeback
registers.
Signed-off-by: Archit Taneja <archit@ti.com>
The struct omap_overlay_info passed to dispc_ovl_setup() is used to configure
DISPC registers. It shouldn't modify the overlay_info structure. The pos_y field
was being changed in dispc_ovl_setup in the case of interlaced displays. Fix
this and const qualifier to the omap_overlay_info argument.
Signed-off-by: Archit Taneja <archit@ti.com>
Now that an omap_dss_output can be used to link between managers and devices, we
can remove the old way of setting manager and device links. This involves
removing the device and manager pointers from omap_overlay_manager and
omap_dss_device respectively, and removing the set_device/unset_device ops from
omap_overlay_manager.
Signed-off-by: Archit Taneja <archit@ti.com>
An overlay isn't allowed to be enabled/disabled if it isn't connected to an
omap_dss_device. This requirement isn't needed any more. An overlay can be
enabled/disabled as long as it has an output connected to it. The output may
not be connected to a device, but we can be assured that the connected
manager's output is in use by an output interface.
Signed-off-by: Archit Taneja <archit@ti.com>
A manager is not connected to a device directly any more. It first connects
to an output, and then to the display. Update overlay and manager get_device ops
to return the device via the connected output.
Signed-off-by: Archit Taneja <archit@ti.com>
The display sysfs attribute's store function needs to be changed with the
introduction of outputs.
The DSS driver ensures that there is one display per output, and that a
registered omap_dss_device will have an output connected to it. The display
sysfs store function unsets the current output connected to the manager, and
sets it with the output connected to the new display. If the new display doesn't
have an output for some reason, we just bail out. The function doesn't set/unset
output->device links. These remain the same as when the omap_dss_device was
registered.
Signed-off-by: Archit Taneja <archit@ti.com>
To retrieve the manager pointer via a device, we need to now access it via the
output to which the device is connected. Make this change in omapfb_ioctl()
where the WAITFORVSYNC ioctl tries to access the manager's device.
Signed-off-by: Archit Taneja <archit@ti.com>
With addition of output entities, a device connects to an output, and an output
connects to overlay manager. Replace the dssdev->manager references with
dssdev->output->manager to access the manager correctly.
When enabling the HDMI output, check whether the output entity connected to
display is not NULL.
Signed-off-by: Archit Taneja <archit@ti.com>
With addition of output entities, a device connects to an output, and an output
connects to overlay manager. Replace the dssdev->manager references with
dssdev->output->manager to access the manager correctly.
When enabling the VENC output, check whether the output entity connected to
display is not NULL.
Signed-off-by: Archit Taneja <archit@ti.com>
With addition of output entities, a device connects to an output, and an output
connects to overlay manager. Replace the dssdev->manager references with
dssdev->output->manager to access the manager correctly.
When enabling the RFBI output, check whether the output entity connected to
display is not NULL.
Signed-off-by: Archit Taneja <archit@ti.com>
With addition of output entities, a device connects to an output, and an output
connects to overlay manager. Replace the dssdev->manager references with
dssdev->output->manager to access the manager correctly.
When enabling the SDI output, check whether the output entity connected to
display is not NULL.
Signed-off-by: Archit Taneja <archit@ti.com>
With addition of output entities, a device connects to an output, and an output
connects to overlay manager. Replace the dssdev->manager references with
dssdev->output->manager to access the manager correctly.
When enabling the DSI output, check whether the output entity connected to
display is not NULL.
In dsi_init_display(), the display won't be connected to the DSI output yet,
that happens later in dss_recheck_connections() in the panel driver's probe. Get
the dsidev platform device pointer using the DSI moudle number provided in the
omap_dss_device struct.
Signed-off-by: Archit Taneja <archit@ti.com>
dsi_pdev_map is a struct visible globally in the DSI driver to get the platform
device pointer of the DSI device corresponding to it's module ID. This was
required because there was no clean way to derive the platform device from
the DSI module instance number or from the connected panel.
With the new output entity, it is possible to retrieve the platform device
pointer if the omap_dss_output pointer is available. Modify the functions
dsi_get_dsidev_from_dssdev() dsi_get_dsidev_from_id() so that they use output
instead of dsi_pdev_map to retrieve the dsi platform device pointer.
Signed-off-by: Archit Taneja <archit@ti.com>
With addition of output entities, a device connects to an output, and an output
connects to overlay manager. Replace the dssdev->manager references with
dssdev->output->manager to access the manager correctly.
When enabling the DPI output, check whether the output entity connected to
display is not NULL.
Signed-off-by: Archit Taneja <archit@ti.com>
Links between DSS entities are made in dss_init_connections() when a panel
device is registered, and are removed in dss_uninit_connections() when the
device is unregistered. Modify these functions to incorporate the addition of
outputs.
The fields in omap_dss_device struct gives information on which output and
manager to connect to. The desired manager and output pointers are retrieved and
prepared to form the desired links. The output is linked to the device, and then
the manager to the output.
A helper function omapdss_get_output_from_device() is created to retrieve the
output from the display by checking it's type, and the module id in case of DSI.
Signed-off-by: Archit Taneja <archit@ti.com>
With the introduction of output entities, managers will now connect to outputs.
Use the helper op for overlays named get_device. This will abstract away the
information on how to get the device from an overlay.
Using the helper function will reduce the number of pointer dereferences a user
of OMAPDSS needs to do and reduce risk of a NULL dereference.
Signed-off-by: Archit Taneja <archit@ti.com>
With the introduction of output entities, managers will now connect to outputs.
Create helper ops for overlays and managers named get_device. This will abstract
away the information on how to get the device from an overlay or an overlay
manager. The get_device ops currently retrieve the output via a
ovl->manager->device reference. This will be later replaced by
ovl->manager->output->device references.
Signed-off-by: Archit Taneja <archit@ti.com>
Add set_output/unset_output ops for overlay managers, these form links between
managers and outputs. Create a function in dss features which tell all the
output instances that connect to a manager, use it when a manager tries to set
an output. Add a constraint of not unsetting an output when the manager is
enabled.
Keep the omap_dss_device pointer and set/unset_device ops in overlay_manager for
now to not break things. Keep the dss feature function get_supported_displays
as it's used in some places. These will be removed later.
Signed-off-by: Archit Taneja <archit@ti.com>
An output entity represented by the struct omap_dss_output connects to a
omap_dss_device entity. Add functions to set or unset an output's device. This
is similar to how managers and devices were connected previously. An output can
connect to a device without being connected to a manager. However, the output
needs to eventually connect to a manager so that the connected panel can be
enabled.
Keep the omap_overlay_manager pointer in omap_dss_device for now to prevent
breaking things. This will be removed later when outputs are supported
completely.
Signed-off-by: Archit Taneja <archit@ti.com>
Add output structs to output driver's private data. Register output instances by
having an init function in the probes of the platform device drivers for
different outputs. The *_init_output for each output registers the output and
fill up the output's plaform device, type and id fields. The *_uninit_output
functions unregister the output.
In the probe of each interface driver, the output entities are initialized
before the *_probe_pdata() functions intentionally. This is done to ensure that
the output entity is prepared before the panels connected to the output are
registered. We need the output entities to be ready because OMAPDSS will try
to make connections between overlays, managers, outputs and devices during the
panel's probe.
Signed-off-by: Archit Taneja <archit@ti.com>
The current OMAPDSS design contains 3 software entities: Overlays, Managers and
Devices. These map to pipelines, overlay managers and the panels respectively in
hardware. One or more overlays connect to a manager to represent a composition,
the manager connects to a device(generally a display) to display the content.
The part of DSS hardware which isn't represented by any of the above entities
are interfaces/outputs that connect to an overlay manager, i.e blocks like DSI,
HDMI, VENC and so on. Currently, an overlay manager directly connects to the
display, and the output to which it is actually connected is ignored. The panel
driver of the display is responsible of calling output specific functions to
configure the output.
Adding outputs as a new software entity gives us the following benefits:
- Have exact information on the possible connections between managers and
outputs: A manager can't connect to each and every output, there only limited
hardware links between a manager's video port and some of the outputs.
- Remove hacks related to connecting managers and devices: Currently, default
links between managers and devices are set in a not so clean way. Matching is
done via comparing the device type, and the display types supported by the
manager. This isn't sufficient to establish all the possible links between
managers, outputs and devices in hardware.
- Make panel drivers more generic: The DSS panel drivers currently call
interface/output specific functions to configure the hardware IP. When making
these calls, the driver isn't actually aware of the underlying output. The
output driver extracts information from the panel's omap_dss_device pointer
to figure out which interface it is connected to, and then configures the
corresponding output block. An example of this is when a DSI panel calls
dsi functions, the dsi driver figures out whether the panel is connected
to DSI1 or DSI2. This isn't correct, and having output as entities will
give the panel driver the exact information on which output to configure.
Having outputs also gives the opportunity to make panel drivers generic
across different platforms/SoCs, this is achieved as omap specific output
calls can be replaced by ops of a particular output type.
- Have more complex connections between managers, outputs and devices: OMAPDSS
currently doesn't support use cases like 2 outputs connect to a single
device. This can be achieved by extending properties of outputs to connect to
more managers or devices.
- Represent writeback as an output: The writeback pipeline fits well in OMAPDSS
as compared to overlays, managers or devices.
Add a new struct to represent outputs. An output struct holds pointers to the
manager and device structs to which it is connected. Add functions which can
register/unregister an output, or look for one. Create an enum which represent
each output instance.
Signed-off-by: Archit Taneja <archit@ti.com>
The functions dss_mgr_wait_for_go() and dss_mgr_wait_for_go_ovl() check if there
is an enabled display connected to the manager before trying to see the state of
the GO bit.
The checks related to the display can be replaced by checking the state of the
manager, i.e, whether the manager is enabled or not. This makes more sense than
checking with the connected display as the GO bit behaviour is more connected
with the manager state rather than the display state. A GO bit can only be set
if the manager is enabled. If a manager isn't enabled, we can safely assume that
the GO bit is not set.
Signed-off-by: Archit Taneja <archit@ti.com>
Many of the DSI functions receive the connected panel's omap_dss_device pointer
as an argument. The platform device pointer is then derived via omap_dss_device
pointers.
Most of these functions don't really require omap_dss_device pointer anymore
since we now keep copies of parameters in the driver data which were previously
available only via omap_dss_device. Replace the arguments with platform device
pointers for such functions.
Signed-off-by: Archit Taneja <archit@ti.com>
tlpx_half bit field in DSI_DSIPHY_CFG1 is [20,16], not [22,16] as
accessed in the code currently. Fix this.
The bug should not have caused any problems on OMAP3/4, as the bits
21,22 are unused. They are used on OMAP5, though.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In OMAP4 and OMAP5 when TILER 2D burst mode is used, a maximum of one line can
be skipped as per the respective TRMs. The MBlockStride OCP signal, which is
sum of ROWINC and image width in memory, is only 17 bits wide. In 2D mode TILER
supports 8192, 16384, 32768 and 65536 values of MBlockStride. In case when 2 or
more lines are skipped the ROWINC value exceeds 65536 resulting in OCP errors.
So, maximum vertical predecimation achievable is 2.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The TPS65217 chip contains a boost converter and current sinks which can be
used to drive LEDs for use as backlights. Expose this functionality via the
backlight API.
Tested on an AM335x based custom board with a single WLED string, using
different values for ISEL and FDIM (though it would be hard to tell the
difference except for the value in WLEDCTRL1). Both instantiation through the
device tree and by passing platform data have been tested. Testing has been
done with an Androidized 3.2 kernel from the rowboat project. Koen Kooi
reported the driver to be working on a Beaglebone board with LCD3 cape
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This series adds basic OMAP5 DSS functionality, mainly related to DSS core, DPI
and DSI.
* omap5-dss:
OMAPDSS: DSI: make OMAP2_DSS_DSI depend on ARCH_OMAP5
OMAPDSS: DSI: Add code to disable PHY DCC
OMAPDSS: DSI: Add new linebuffer size for OMAP5
OMAPDSS: DSI: Add FEAT_DSI_PLL_REFSEL
OMAPDSS: DSI: Add FEAT_DSI_PLL_SELFREQDCO
OMAPDSS: Add support for DPI source selection
OMAPDSS: move dss feats to the end of dss.c
OMAPDSS: Add basic omap5 features to dss and dispc
OMAPDSS: DSI: improve DSI clock calcs for DISPC
This series contains patches that change how omapdss's panel devices
(omap_dss_device) are initialized and registered. There are two patches that
change behaviour, the rest are just cleanups:
The patch "omap_dss_register_device() doesn't take display index" affects the
number for the "displayX" sysfs files. This hopefully doesn't affect the
userspace, as the number has never been a clear indication of what the
particular display is.
The patch "register only one display device per output" affects how panel
devices are created. Currently we support multiple panels per output, i.e. you
could have DVI and an LCD displays using the same DPI output, as long as the
DVI and LCD are not used at the same time.
This patch changes the omapdss driver to only register one display device per
output. If there are multiple displays for the output, either the first one is
picked or, if def_display has been defined in kernel parameters and the
def_display is one of the displays for this output, the def_display is picked.
See the patch for more information.
OMAPDSS: alloc dssdevs dynamically
OMAPDSS: cleanup dss_recheck_connections further
OMAPDSS: cleanup dss_recheck_connections
OMAPDSS: handle errors in dss_init_device
OMAPDSS: explicitely initialize dssdev->channel for new displays
OMAPDSS: register only one display device per output
OMAPDSS: Add dss_get_default_display_name()
OMAPDSS: omap_dss_register_device() doesn't take display index
On our AM3505 based board, dpi.c complains that there is no VDDS_DSI
regulator and the framebuffer cannot be enabled. However, this check
does not seem to apply to AM3505/17 chips.
This patch adds new features list for AM35xxx, which is the same as for
OMAP3 except the VDDS_DSI is removed.
Signed-off-by: Raphael Assenat <raph@8d.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP5 DSI PHY has DCC (Duty Cycle Corrector) block, and by default DCC
is enabled and thus the PLL clock is divided by 2 to get the DSI DDR
clk. This divider has been 4 for all previous OMAPs, and changing it
needs some reorganization of the code. The DCC can be disabled, and in
that case the divider is back to the old 4.
This patch adds dss feature for the DCC, and adds code to always disable
the DCC.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP5's DSI has a larger line buffer than earlier OMAPs. This patch adds
support for this to the DSI driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add FEAT_DSI_PLL_REFSEL. OMAP5's DSI PLL needs configuration to select
the reference clock to be used. We always use SYSCLK.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add FEAT_DSI_PLL_SELFREQDCO. OMAP5's DSI PLL has a new configuration
option that needs to be programmed depending on the PLL's output clock
frequency.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We can select the video source for DPI output as follows:
OMAP2/3: always LCD1
OMAP4: LCD2 or DIGIT
OMAP5: LCD1/LCD2/LCD3/DIGIT
This patch adds support to select the source, and makes dpi.c call the
function to set the source.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: David Anders <x0132446@ti.com>
Move dss_features to the end of dss.c the same way they are in dispc.c,
so that we don't have to declare prototypes for static feat-related
functions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit ee144e645a added
dsi_pll_calc_ddrfreq() which calculates PLL dividers based on given DSI
bus clock speed. The function works ok, but it can be improved for the
DISPC clock calc.
The current version calculates the clock going from the PLL to the DISPC
simply by setting the clock as close to DISPC maximum as possible, and
the pixel clock is calculated based on that.
This patch changes the function to calculate DISPC clock more
dynamically, iterating through different DISPC clocks and pixel clock
values, and thus we'll get more suitable pixel clocks.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
remove existing non-dt code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQXBatAAoJEAKiPfwuf9N/VZoIAI7PKNwakjM/KDiVzytwqZ+U
h9kkjYW4ra8MH+jpjFQqvSyIJ3U+t016xqW3ZbqRuZBDgH0I7Gax7QoAZ/ljPlpG
RAKl2l9WVPiBSwCESTpvR5lafBLklk6fL0Z267qIxDGld6YBiWHvTKIh1zDmeCWW
hgDeWtcb1M61VlPrj9nPnCze66h2dUk+QSxaCodv7co5kzb0Q4S7U64BCs0hGe01
kkdoUwnBjdeK0cUhDAJAP1vRyk04N16+H7yp4npmKhv/blKVc3MIRjg1iBV78ncd
Kke/G1B9TJRpNTXdySYnsDQpaCWNSAryKXKkdxP0gh6MW8CMKYc1mdKYcEP3Tk8=
=xG1+
-----END PGP SIGNATURE-----
Merge tag 'vt8500-for-next' of git://git.code.sf.net/p/linuxwmt/code into next/dt
From Tony Prisk:
Update arch-vt8500 and drivers to device tree and
remove existing non-dt code.
* tag 'vt8500-for-next' of git://git.code.sf.net/p/linuxwmt/code:
arm: vt8500: Update arch-vt8500 to devicetree support.
arm: vt8500: gpio: Devicetree support for arch-vt8500
arm: vt8500: doc: Add device tree bindings for arch-vt8500 devices
arm: vt8500: clk: Add Common Clock Framework support
video: vt8500: Add devicetree support for vt8500-fb and wm8505-fb
serial: vt8500: Add devicetree support for vt8500-serial
rtc: vt8500: Add devicetree support for vt8500-rtc
arm: vt8500: Add device tree files for VIA/Wondermedia SoC's
Resolved add/change conflict in drivers/clk/Makefile.
Signed-off-by: Olof Johansson <olof@lixom.net>
'dsim' is allocated and checked for NULL in the probe function.
Hence this check is redundant. This cleanup also fixes a potential NULL
pointer dereference error when dsim which is NULL references its member
in the error print message.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This driver doesn't need to use these mach includes so remove
them. This is a necessary step to support a single zImage.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The value of AUX channel differential amplitude current is changed
from 8 mA to 16 mA, in order to increase AUX channel voltage level.
In this case, AUX channel voltage level can be changed from 400 mV
to 800 mV, when resistance between AUX TX and RX is 100 ohm.
According to DP spec, although the normative voltage level is 390 mV,
the informative voltage level is 430 mV. So, 800 mV can be helpful
to improve voltage margin of AUX channel.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch adds bit-masking for LINK_TRAINING_CTL register, when
pre-emphasis level is set. The bit 3 and bit 2 of LINK_TRAINING_CTL
register are used for pre-emphasis level setting, so other bits
should be masked.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch fixes the checkpatch warnings listed below:
WARNING: usleep_range should not use min == max args; see Documentation/timers/timers-howto.txt
WARNING: quoted string split across lines
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Use devm_request_and_ioremap instead of request_mem_region + devm_ioremap.
This also fixes the following compile error introduced in commit b2ca7f4d
("drivers/video/jz4740_fb.c: use devm_ functions"):
drivers/video/jz4740_fb.c: In function 'jzfb_probe':
drivers/video/jz4740_fb.c:676:2: error: implicit declaration of function 'devm_ioremap'
drivers/video/jz4740_fb.c:676:13: warning: assignment makes pointer from integer without a cast
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
It doesn't seem these spinlocks were properly initialized.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Using list_move_tail() instead of list_del() + list_add_tail().
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
As detailed in the thread titled "viafb PLL/clock tweaking causes XO-1.5
instability," enabling or disabling the IGA1/IGA2 clocks causes occasional
stability problems during suspend/resume cycles on this platform.
This is rather odd, as the documentation suggests that clocks have two
states (on/off) and the default (stable) configuration is configured to
enable the clock only when it is needed. However, explicitly enabling *or*
disabling the clock triggers this system instability, suggesting that there
is a 3rd state at play here.
Leaving the clock enable/disable registers alone solves this problem.
This fixes spurious reboots during suspend/resume behaviour introduced by
commit b692a63a.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: stable@vger.kernel.org
To check channel equalization, the value of LANE_ALIGN_STATUS_UPDATED is
necessary in exynos_dp_channel_eq_ok(). Also, link_align includes this value.
However, link_status does not include this value, so it makes the problem
that channel equalization is failed during link training.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
It is expected that LCDC to continue to be disabled after
resume if it is blanked before suspend. This is also true
for DVFS. But it is observed that LCDC being enabled after
suspend/resume cycle or DVFS.
Correcting it by having check for FB_BLANK_UNBLANK before
enabling.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This fixes below build error:
CC [M] drivers/video/mbx/mbxfb.o
drivers/video/mbx/mbxfb.c: In function 'mbxfb_probe':
drivers/video/mbx/mbxfb.c:942:2: error: implicit declaration of function 'devm_ioremap_nocache' [-Werror=implicit-function-declaration]
drivers/video/mbx/mbxfb.c:942:22: warning: assignment makes pointer from integer without a cast [enabled by default]
drivers/video/mbx/mbxfb.c:952:21: warning: assignment makes pointer from integer without a cast [enabled by default]
cc1: some warnings being treated as errors
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch removes the video driver for pnx4008. The architecture is being
removed via the arm-soc tree.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Wait for active frame transfer to complete after disabling LCDC.
At the same this wait is not be required when there are sync and
underflow errors.
Patch applies for revision 2 of LCDC present am335x.
More information on disable and reset sequence can be found in
section 13.4.6 of AM335x TRM @www.ti.com/am335x.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
the driver's module init and exit functions are calling
platform_driver_register and platform_driver_unregister and doing nothing
else.
This same as that of the module_platform_driver,
remove this init and exit functions and use the module_platform_driver instead
Signed-off-by: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch solves problems with the error handling by
introducing labels for proper error paths and it also
frees resources that where missed.
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The code 124 (0x7C, |) is rendered as a broken line in two
fonts, instead of a continuous line. Some keyboards show a
"broken bar" on one of theirs keys, other show a (continuous)
"vertical line".
Signed-off-by: Bjarni Ingi Gislason <bjarniig@rhi.hi.is>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
__iomem annotation cleanup branch from Arnd.
* cleanup/__iomem: (21 commits)
net: seeq: use __iomem pointers for MMIO
video: da8xx-fb: use __iomem pointers for MMIO
scsi: eesox: use __iomem pointers for MMIO
serial: ks8695: use __iomem pointers for MMIO
input: rpcmouse: use __iomem pointers for MMIO
ARM: samsung: use __iomem pointers for MMIO
ARM: spear13xx: use __iomem pointers for MMIO
ARM: sa1100: use __iomem pointers for MMIO
ARM: prima2: use __iomem pointers for MMIO
ARM: nomadik: use __iomem pointers for MMIO
ARM: msm: use __iomem pointers for MMIO
ARM: lpc32xx: use __iomem pointers for MMIO
ARM: ks8695: use __iomem pointers for MMIO
ARM: ixp4xx: use __iomem pointers for MMIO
ARM: iop32x: use __iomem pointers for MMIO
ARM: iop13xx: use __iomem pointers for MMIO
ARM: integrator: use __iomem pointers for MMIO
ARM: imx: use __iomem pointers for MMIO
ARM: ebsa110: use __iomem pointers for MMIO
ARM: at91: use __iomem pointers for MMIO
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Update vt8500-fb, wm8505-fb and wmt-ge-rops to support device
tree bindings.
Small change in wm8505-fb.c to support WM8650 framebuffer color
format.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
This is only used by omap1.
And to fix things properly, this should not be included
from the drivers at all.
Acked-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Cc: linux-mtd@lists.infradead.org
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: linux-input@vger.kernel.org
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Liam Girdwood <lrg@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: alsa-devel@alsa-project.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are moving omap2+ to use the device tree based pinctrl-single.c
and will be removing the old mux framework. This will remove the
omap1 specific parts from plat-omap.
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-pcmcia@lists.infradead.org
Cc: spi-devel-general@lists.sourceforge.net
Signed-off-by: Tony Lindgren <tony@atomide.com>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the omap include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: "Benoît Cousson" <b-cousson@ti.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: Jean Pihet <j-pihet@ti.com>
Cc: J Keerthy <j-keerthy@ti.com>
Cc: linux-omap@vger.kernel.org
ARM is moving to stricter checks on readl/write functions,
so we need to use the correct types everywhere.
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove the register offset definition. All these register offset
are transfered as IORESOURCE_REG resources.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We currently create omap_dss_devices statically in board files, and use
those devices directly in the omapdss driver. This model prevents us
from having the platform data (which the dssdevs in board files
practically are) as read-only, and it's also different than what we will
use with device tree.
This patch changes the model to be in line with DT model: we allocate
the dssdevs dynamically, and initialize them according to the data in
the board file's dssdev (basically we memcopy the dssdev fields).
The allocation and registration is done in the following steps in the
output drivers:
- Use dss_alloc_and_init_device to allocate and initialize the device.
The function uses kalloc and device_initialize to accomplish this.
- Call dss_copy_device_pdata to copy the data from the board file's
dssdev
- Use dss_add_device to register the device.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cleanup dss_recheck_connections, move and rename it to a static
dss_init_connections function inside display.c. Improve the function to
return errors, and implement a matching dss_uninit_connections that can
be used to free the mgr->dssdev link.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss_recheck_connections is quite a mess. With the previous commit that
initializes the channel field for HDMI and VENC displays, we can greatly
simplify the dss_recheck_connections.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
HDMI and VENC outputs always use the DIGIT output from DISPC. The dssdev
struct contains "channel" field which is used to specify the DISPC
output for the display, but this was not used for HDMI and VENC.
This patch fills the channel field explicitely for HDMI and VENC
displays so that we can always rely on the channel field.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have boards with multiple panel devices connected to the same
physical output, of which only one panel can be enabled at one time.
Examples of these are Overo, where you can use different daughter boards
that have different LCDs, and 3430SDP which has an LCD and a DVI output
and a physical switch to select the active display.
These are supported by omapdss so that we add all the possible display
devices at probe, but the displays are inactive until somebody enables
one. At this point the panel driver starts using the DSS, thus reserving
the physcal resource and excluding the other panels.
This is problematic:
- Panel drivers can't allocate their resources properly at probe(),
because the resources can be shared with other panels. Thus they can
be only reserved at enable time.
- Managing this in omapdss is confusing. It's not natural to have
child devices, which may not even exist (for example, a daughterboard
that is not connected).
Only some boards have multiple displays per output, and of those, only
very few have possibility of switching the display during runtime.
Because of the above points:
- We don't want to make omapdss and all the panel drivers more complex
just because some boards have complex setups.
- Only few boards support runtime switching, and afaik even then it's
not required. So we don't need to support runtime switching.
Thus we'll change to a model where we will have only one display device
per output and this cannot be (currently) changed at runtime. We'll
still have the possibility to select the display from multiple options
during boot with the default display option.
This patch accomplishes the above by changing how the output drivers
register the display device. Instead of registering all the devices
given from the board file, we'll only register one. If the default
display option is set, the output driver selects that display from its
displays. If the default display is not set, or the default display is
not one of the output's displays, the output driver selects the first
display.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add function dss_get_default_display_name() which returns the name of
the default display, given from the board file or via module parameters.
The default display name can be used by output drivers to decide which
display is the wanted one.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We used to have all the displays of the board in one list, and we made a
"displayX" directory in the sysfs, where X was the index of the display
in the list.
This doesn't work anymore with device tree, as there's no single list to
get the number from, and it doesn't work very well even with non-DT as
we need to do some tricks to get the index nowadays.
This patch changes omap_dss_register_device() so that it doesn't take
disp_num as a parameter anymore, but uses a private increasing counter
for the display number.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The majority of the DMI checks in efifb are for cases where the bootloader
has provided invalid information. However, on some machines the overrides
may do more harm than good due to configuration differences between machines
with the same machine identifier. It turns out that it's possible for the
bootloader to get the correct information on GOP-based systems, but we
can't guarantee that the kernel's being booted with one that's been updated
to do so. Add support for a capabilities flag that can be set by the
bootloader, and skip the DMI checks in that case. Additionally, set this
flag in the UEFI stub code.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Merge Gavin patches from the PCI tree as subsequent powerpc
patches are going to depend on them
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the w90x900 include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the vt8500 include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the pxa include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Paul Parsons <lost.distance@yahoo.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Acked-By: Stefan Schmidt <stefan@openezx.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Daniel Ribeiro <drwyrm@gmail.com>
Cc: Harald Welte <laforge@openezx.org>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Tomas Cech <sleep_walker@suse.cz>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: openezx-devel@lists.openezx.org
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the msm include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Chris Ball <cjb@laptop.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: linux-arm-msm@vger.kernel.org
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the imx include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the ep93xx include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Dan Williams <djbw@fb.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Mika Westerberg <mika.westerberg@iki.fi>
Cc: Axel Lin <axel.lin@gmail.com>
As the interrupts should only be defined in the platform_data, and
eventually coming from device tree, there's no need to define them
in header files.
Let's remove the hardcoded references to irqs.h and fix up the includes
so we don't rely on headers included in irqs.h. Note that we're
defining OMAP_INTC_START as 0 to the interrupts. This will be needed
when we enable SPARSE_IRQ. For some drivers we need to add
#include <plat/cpu.h> for now until these drivers are fixed to
remove cpu_is_omapxxxx() usage.
While at it, sort som of the includes the standard way, and add
the trailing commas where they are missing in the related data
structures.
Note that for drivers/staging/tidspbridge we just define things
locally.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The framebuffers are cleared with the function omapfb_clear_fb(), which
internally calls cfb_fillrect(). The boot logo is copied on to the
framebuffer when the fb device is registered with fb framework.
omapfb_clear_fb() is called after the framebuffer is registered, leading to
the boot logo getting cleared. Clear the framebuffers using omapfb_clear_fb()
before registering the framebuffer devices.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now resource of 88pm860x backlight is changed from IORESOURCE_IO
to IORESOURCE_REG. In original driver, the resource is using
self-defined IORESOURCE_IO. So change the resource to register
offset to match the definition of IORESOURCE_REG.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
omap1 backlight platform data resides inside plat/board.h while it
should be inside include/linux/...
Move the omap1 backlight platform data to
include/linux/platform_data/.
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When we removed fifomerge support, we also changed dss_ovl_disable so
that it doesn't wait for the hardware to be finished with the overlay.
This may cause a problem when changing the overlay's manager, as
changing the manager is an immediate change. Thus if the overlay is
still being used by the HW when the manager is changed, there may be
glitches on the screen.
This patch adds a wait into dss_ovl_unset_manager, which ensures the
overlays are disabled in the HW.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
set_timings function of DSS's output drivers are not consistent. Some of
them disable the output, set the timings, and re-enable the output. Some
set the timings on the fly, while the output is enabled. And some just
store the given timings, so that they will be taken into use next time
the output is enabled.
We require the DISPC output to be disabled when changing the timings,
and so we can change all the output drivers' set_timings to just store
the given timings.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP4's GFX overlay has smaller fifo than the rest of the overlays
(including writeback "overlay"). This seems to be the reason for
underflows in some more demanding scenarios.
We can avoid the problems by using the WB fifo for GFX overlay, and vice
versa. WB usage is not supported yet, but when it will, it should
perform just fine with smaller fifo as there are no hard realtime
constraints with WB.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP4+ allows assigning the overlay FIFOs freely, but that is not
supported by omapdss yet. This patch takes a step forward by improving
the fifo management to be more flexible.
dispc.c is changed to keep track of the sizes of each fifo, and also the
overlay using each fifo.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This reverts commit fb01197422.
Adding fifo merge feature as an omapdss internal configuration was a
mistake. We cannot hide from the users of omapdss the complexities of
fifo merge.
The previous commit removed fifo merge itself, and this removes the
remaining fifo merge support functions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This reverts commit 1d71f42b35.
Adding fifo merge feature as an omapdss internal configuration was a
mistake. We cannot hide from the users of omapdss the complexities of
fifo merge.
This commit removes the fifo merge support, which luckily is easily done
as it was handled totally inside apply.c. Note that this is not a 1:1
revert, but some resolving was needed for the dss_ovl_setup_fifo.
The plan is to try fifo merge again later when it is more clear how the
hardware acts in various situations, and how the omapdrm wants to use
fifo merge.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss_mgr_set_timings() can only be called when the output is not active.
This means that most of the code in the function is extra, as there's no
need to write the values to registers, etc, because that will be handled
when the output will be enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss_mgr_set_lcd_config() can only be called when the output is not
active. This means that most of the code in the function is extra, as
there's no need to write the values to registers, etc, because that will
be handled when the output will be enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Separate sysfs code for managers to a separate file. This is a bit
cleaner, and will allow us later to easily switch off the sysfs support
via Kconfig option.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Separate sysfs code for overlays to a separate file. This is a bit
cleaner, and will allow us later to easily switch off the sysfs support
via Kconfig option.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reorganize taal driver to make it easier to integrate device tree code.
Instead of storing the panel's platform data, we'll "parse" the platform
data and store the required information in driver's own data. This way
adding device tree data parsing is simple.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently vram.c clears the allocated memory automatically using OMAP
system DMA. In an effort to reduce OMAP dependencies, we'll do the
memory clear with CPU from now on.
The previous patch implemented memory clear in the omapfb driver, and
this patch removes the now obsolete clear functionality from vram.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Currently vram.c clears the allocated memory automatically using OMAP
system DMA. In an effort to reduce OMAP dependencies, we'll do the
memory clear with CPU from now on.
This patch implements clearing of the framebuffer in omapfb, using
cfb_fillrect() to do the actual clear.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use devm_ functions in panel-taal.c's probe when possible. Also reorder
the initialization sequence so that devm_ allocations are done before
things that require explicit freeing. This simplifies the probe and
remove functions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Recent commit dca2b1522c (OMAPDSS: DSI:
Maintain copy of operation mode in driver data) broke DSI for video mode
displays. The commit changed the way dssdev->caps are initialized, and
the result was that every DSI display is initialized with manual-update
and tear-elim caps.
The code that sets dssdev->caps is not very good, even when fixed.
omapdss driver shouldn't be writing dssdev->caps at all.
This patch fixes the problem with video mode displays by moving the
initialization of dssdev->caps to the panel driver. The same change is
done for RFBI.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently the way to configure clocks related to DSI (both DSI and DISPC
clocks) happens via omapdss platform data. The reason for this is that
configuring the DSS clocks is a very complex problem, and it's
impossible for the SW to know requirements about things like
interference.
However, for general cases it should be fine to calculate the dividers
for clocks in the SW. The calculated clocks are probably not perfect,
but should work.
This patch adds support to calculate the dividers when using DSI command
mode panels. The panel gives the required DDR clock rate and LP clock
rate, and the DSI driver configures itself and DISPC accordingly.
This patch is somewhat ugly, though. The code does its job by modifying
the platform data where the clock dividers would be if the board file
gave them. This is not how it's going to be in the future, but allows us
to have quite simple patch and keep the backward compatibility.
It also allows the developer to still give the exact dividers from the
board file when there's need for that, as long as the panel driver does
not override them.
There are also other areas for improvement. For example, it would be
better if the panel driver could ask for a DSI clock in a certain range,
as, at least command mode panels, the panel can work fine with many
different clock speeds.
While the patch is not perfect, it allows us to remove the hardcoded
clock dividers from the board file, making it easier to bring up a new
panel and to use device tree from omapdss.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The HDMI driver requires vdda_hdmi_dac power for operation, but does not
enable it. This has worked because the regulator has been always
enabled.
But this may not always be the case, as I encountered when implementing
HDMI device tree support.
This patch changes the HDMI driver to use the vdda_hdmi_dac.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
TPD12S015A spec says to wait 300us after setting CT_CP_HPD gpio for the
5V power output to reach 90% of the voltage. This patch adds the delay
to the driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We currently manage HDMI GPIOs in the board files via
platform_enable/disable calls. This won't work with device tree, and in
any case the correct place to manage the GPIOs is in the HDMI driver.
This patch moves the handling of the GPIOs to the HDMI driver. The GPIO
handling is moved to the common hdmi.c file, and this probably needs to
be revisited when adding OMAP5 HDMI support to see if the GPIO handling
needs to be moved to IP specific files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
virt_to_abs() is just a wrapper around __pa(), call __pa() directly.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
SW reset sets DP TX to initial value, so configurations for analog parameter
and interrupt are not set properly. Therefore, exynos_dp_init_analog_param()
and exynos_dp_init_interrupt() should be moved to after sw reset is called,
in order to set these values properly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch changes return type of exynos_dp_init_video to void,
because the return value is unnecessary.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Fix the return value of exynos_dp_get_pll_lock_status to
reflect what it actually returns.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Olof Johansson <olofj@chromium.org>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch adds the function name to aux transaction failure messages
so we can tell which transaction is failing. It also changes the level
of Aux Transaction fail messages from error to debug. We retry the
transactions a few times and will report errors if warranted outside of
this function.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Bernie Thompson <bhthompson@chromium.org>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Initialize return variable before exiting on an error path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
LCD controller on am335x supports 24bpp raster configuration in addition
to ones on da850. LCDC also supports 24bpp in unpacked format having
ARGB:8888 32bpp format data in DDR, but it doesn't interpret alpha
component of the data.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Michal maybe forgot it merely, we should add code
to check the return value of kzalloc to make the
code more robust.
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch checks time loop for RPLY_RECEIV which means that
AUX channel command reply is received.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch replaces the use of kzalloc by devm_kzalloc.
Additionally, this patch fixes a memory leak: some memory was allocated for
'panel' but not released when the subsequent call to setup_vsync fails.
Signed-off-by: Damien Cassou <damien.cassou@lifl.fr>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch replaces the use of kzalloc by devm_kzalloc.
Signed-off-by: Damien Cassou <damien.cassou@lifl.fr>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in the
probe function of a platform device and is only freed in the remove function.
Signed-off-by: Damien Cassou <damien.cassou@lifl.fr>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in the
probe function of a platform device and is only freed in the remove function.
Signed-off-by: Damien Cassou <damien.cassou@lifl.fr>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The devm_ functions allocate memory that is released when a driver
detaches. This patch uses devm_clk_get() for these functions.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Fixes the following sparse warnings:
drivers/video/exynos/exynos_mipi_dsi.c:208:22: warning:
symbol 'exynos_mipi_dsi_find_lcd_device' was not declared. Should it be static?
drivers/video/exynos/exynos_mipi_dsi.c:268:22: warning:
symbol 'exynos_mipi_dsi_bind_lcd_ddi' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The devm_clk_get function allocates memory that is released when a driver
detaches. This patch uses this function for data that is allocated in the probe
function of a platform device and is only freed in the remove function.
Additionally, this patch removes a null check after platform_get_resource that
is redundant with the one done by devm_request_and_ioremap.
Signed-off-by: Damien Cassou <damien.cassou@lifl.fr>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
Signed-off-by: Damien Cassou <damien.cassou@lifl.fr>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
Signed-off-by: Damien Cassou <damien.cassou@lifl.fr>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
Signed-off-by: Damien Cassou <damien.cassou@lifl.fr>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
Signed-off-by: Damien Cassou <damien.cassou@lifl.fr>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
Signed-off-by: Damien Cassou <damien.cassou@lifl.fr>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
Signed-off-by: Damien Cassou <damien.cassou@lifl.fr>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This patch adds adjustement for voltage swing and pre-emphasis during
Link Training procedure. According to the DP specification, unless all
the LANEx_CR_DONE bits are set, the transmitter must read
the ADJUST_REQUEST_LANEx_x, increase the voltage swing according to
the request, and update the TRAINING_LANEx_SET bytes to match the new
voltage swing setting.
Refer to the DP specification v1.1a, Section 3.5.1.3 Link Training.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
omapfb does not currently set pseudo palette correctly for color depths
above 16bpp, making red text invisible, command like
echo -e '\e[0;31mRED' > /dev/tty1
will display nothing on framebuffer console in 24bpp mode.
This is because temporary variable is declared incorrectly, fix it.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: stable@vger.kernel.org # v3.x
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Commit f476ae9dab (OMAPDSS: APPLY: Remove
DISPC writes to manager's lcd parameters in interface) broke the SDI
output, as it causes the SDI PLL locking to fail.
LCLK and PCLK divisors are located in shadow registers, and we normally
write them to DISPC registers when enabling the output. However, SDI
uses pck-free as source clock for its PLL, and pck-free is affected by
the divisors. And as we need the PLL before enabling the output, we need
to write the divisors early.
It seems just writing to the DISPC register is enough, and we don't need
to care about the shadow register mechanism for pck-free. The exact
reason for this is unknown.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Do a sanity check on these before using them as divisors.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Using kfree to free data allocated with devm_kzalloc causes double frees.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x;
@@
x = devm_kzalloc(...)
...
?-kfree(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The OMAP3 checks have been removed and replaced by a dss feature
FEAT_DPI_USES_VDDS_DSI for cleaner implementation. The patches
"OMAP: DSS2: enable VDDS_DSI when using DPI" (8a2cfea8cc) by Tomi Valkeinen
<tomi.valkeinen@nokia.com> and "ARM: omap: fix oops in
drivers/video/omap2/dss/dpi.c" (4041071571) by Russell King
<rmk+kernel@arm.linux.org.uk> had introduced these checks. As it is evident
from these patches a dependency exists for some DSS pins on VDDS_DSI which is
better shown by dss feature FEAT_DPI_USES_VDDS_DSI.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP4 checks are removed from VENC to provide it a cleaner interface. These
checks were introduced by patches "HACK: OMAP: DSS2: VENC: disable VENC on OMAP4
to prevent crash" (ba02fa37de) by Tomi Valkeinen <tomi.valkeinen@ti.com> and
"OMAPDSS: VENC: fix NULL pointer dereference in DSS2 VENC sysfs debug attr on
OMAP4" (cc1d3e032d) by Danny Kukawka <danny.kukawka@bisect.de> to prevent VENC
from crashing OMAP4 kernel.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
All the cpu_is checks have been moved to dss_init_features function providing a
much more generic and cleaner interface. The OMAP version and revision specific
initializations in various functions are cleaned and the necessary data are
moved to dss_features structure which is local to dss.c.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Functions dss_calc_clock_rates() and dss_get_clock_div() are removed as these
functions have become redundant and no longer used.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
All the cpu_is checks have been moved to dispc_init_features function providing
a much more generic and cleaner interface. The OMAP version and revision
specific functions and data are initialized by dispc_features structure which is
local to dispc.c.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit 7849398fa2 introduced a bug,
causing the following error to be reported:
[ 370.827819] cannot lock PLL
[ 370.830749] CFG1 0x1e
[ 370.833160] CFG2 0x602004
[ 370.835876] CFG4 0x40000
[ 370.838562] omapdss HDMI: Failed to lock PLL
However, HDMI output is still enabled.
The problem is that we enable the HDMI video output temporarily when
reading EDID or detecting if a HDMI cable is connected (ugh), and the
commit above changes the behavior of the driver so that the video
timings are not yet configured at the point when EDID is read.
This patch fixes the problem by configuring the initial VGA timings at
HDMI probe.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
So we've had a fair few reports of fbcon handover breakage between
efi/vesafb and i915 surface recently, so I dedicated a couple of
days to finding the problem.
Essentially the last thing we saw was the conflicting framebuffer
message and that was all.
So after much tracing with direct netconsole writes (printks
under console_lock not so useful), I think I found the race.
Thread A (driver load) Thread B (timer thread)
unbind_con_driver -> |
bind_con_driver -> |
vc->vc_sw->con_deinit -> |
fbcon_deinit -> |
console_lock() |
| |
| fbcon_flashcursor timer fires
| console_lock() <- blocked for A
|
|
fbcon_del_cursor_timer ->
del_timer_sync
(BOOM)
Of course because all of this is under the console lock,
we never see anything, also since we also just unbound the active
console guess what we never see anything.
Hopefully this fixes the problem for anyone seeing vesafb->kms
driver handoff.
v1.1: add comment suggestion from Alan.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now that cancel_delayed_work() can be safely called from IRQ handlers,
there's no reason to use __cancel_delayed_work(). Use
cancel_delayed_work() instead of __cancel_delayed_work() and mark the
latter deprecated.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Roland Dreier <roland@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Initalizers for deferrable delayed_work are confused.
* __DEFERRED_WORK_INITIALIZER()
* DECLARE_DEFERRED_WORK()
* INIT_DELAYED_WORK_DEFERRABLE()
Rename them to
* __DEFERRABLE_WORK_INITIALIZER()
* DECLARE_DEFERRABLE_WORK()
* INIT_DEFERRABLE_WORK()
This patch doesn't cause any functional changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
The VENC driver currently relies on the omap_dss_device struct to configure the
video output polarity. This makes the VENC interface driver dependent on the
omap_dss_device struct.
Make the VENC driver data maintain it's own polarity field. A panel driver
is expected to call omapdss_venc_invert_vid_out_polarity() before enabling the
interface.
Signed-off-by: Archit Taneja <archit@ti.com>
The VENC driver currently relies on the omap_dss_device struct to configure the
venc type. This makes the VENC interface driver dependent on the omap_dss_device
struct.
Make the VENC driver data maintain it's own 'venc type' field. A panel driver
is expected to call omapdss_venc_set_type() before enabling the interface or
changing the type via display sysfs attributes.
Signed-off-by: Archit Taneja <archit@ti.com>
The RFBI driver currently relies on the omap_dss_device struct to receive the
rfbi specific timings requested by the panel driver. This makes the RFBI
interface driver dependent on the omap_dss_device struct.
Make the RFBI driver data maintain it's own rfbi specific timings field. The
panel driver is expected to call omapdss_rfbi_set_interface_timings() to
configure the rfbi timings before the interface is enabled.
Signed-off-by: Archit Taneja <archit@ti.com>
The DSI driver currently relies on the omap_dss_device struct to receive the
video mode timings requested by the panel driver. This makes the DSI interface
driver dependent on the omap_dss_device struct.
Make the DSI driver data maintain it's own video mode timings field. The panel
driver is expected to call omapdss_dsi_set_videomode_timings() to configure the
video mode timings before the interface is enabled.
Signed-off-by: Archit Taneja <archit@ti.com>
The struct omap_dss_dsi_videomode_data holds fields which need to be configured
for DSI to operate in video mode. Rename the struct to dsi_videomode_timings.
One reason to do this is because most of the fields in the struct are timings
related. The other reason is to create a generic op for output specific
timings. This generic op can be considered as a way to set custom or private
timings for the output.
In the case of OMAP, DSI and RFBI require some more timings apart from the
relgular DISPC timings. The structs omap_dss_videomode_timings and rfbi_timings
can be considered as these output specific timings respectively.
Signed-off-by: Archit Taneja <archit@ti.com>
The DSI driver currently relies on the omap_dss_device struct to know the mode
of operation of the DSI protocol(command or video mode). This makes the DSI
interface driver dependent on the omap_dss_device struct.
Make the DSI driver data maintain it's own operation mode field. The panel
driver is expected to call omapdss_dsi_set_operation_mode() before the interface
is enabled.
Signed-off-by: Archit Taneja <archit@ti.com>
The SDI driver currently relies on the omap_dss_device struct to configure the
number of data pairs as specified by the panel. This makes the SDI interface
driver dependent on the omap_dss_device struct.
Make the SDI driver data maintain it's own data lines field. A panel driver
is expected to call omapdss_sdi_set_datapairs() before enabling the interface.
Even though we configure the number of data pairs here, this function would be
finally mapped to a generic interface op called set_data_lines. The datapairs
argument type has been changed from u8 to int at some places to be in sync with
the 'set_data_lines' ops of other interfaces.
Signed-off-by: Archit Taneja <archit@ti.com>
The DPI driver currently relies on the omap_dss_device struct to configure the
number of data lines as specified by the panel. This makes the DPI interface
driver dependent on the omap_dss_device struct.
Make the DPI driver data maintain it's own data lines field. A panel driver
is expected to call omapdss_dpi_set_data_lines() before enabling the interface.
Signed-off-by: Archit Taneja <archit@ti.com>
The RFBI driver currently relies on the omap_dss_device struct to configure the
number of data lines as specified by the panel. This makes the RFBI interface
driver dependent on the omap_dss_device struct.
Make the RFBI driver data maintain it's own data lines field. A panel driver
is expected to call omapdss_rfbi_set_data_lines() to configure the pixel format
before enabling the interface or calling omap_rfbi_configure().
Signed-off-by: Archit Taneja <archit@ti.com>
The RFBI driver currently relies on the omap_dss_device struct to receive the
desired pixel size of the panel. This makes the RFBI interface driver dependent
on the omap_dss_device struct.
Make the RFBI driver data maintain it's own pixel format field. A panel driver
is expected to call omapdss_rfbi_set_pixel_size() to configure the pixel format
before enabling the interface or calling omap_rfbi_configure().
Signed-off-by: Archit Taneja <archit@ti.com>
The DSI driver currently relies on the omap_dss_device struct to receive the
desired pixel format of the panel. This makes the DSI interface driver dependent
on the omap_dss_device struct.
Make the DSI driver data maintain it's own pixel format field. The panel driver
is expected to call omapdss_dsi_set_pixel_format() to configure the pixel format
before the interface is enabled.
Signed-off-by: Archit Taneja <archit@ti.com>
RFBI drivers requires configuration of the update area. Since we don't support
partial updates, the size to be configures is the panel size itself.
Add a timings field in RFBI's driver data. Apart from x_res and y_res, all the
other fields are configured to an initial value when RFBI is enabled. A panel
driver is expected to call omapdss_rfbi_set_size() configure the size of the
panel.
Signed-off-by: Archit Taneja <archit@ti.com>
Partial update suppport was removed from DISPC and DSI sometime back. The RFBI
driver still tries to support partial update without the underlying support in
DISPC.
Remove partial update support from RFBI, only support updates which span acros
the whole panel size. This also helps in DSI and RFBI having similar update
ops.
Signed-off-by: Archit Taneja <archit@ti.com>
The VENC driver currently relies on the timings in omap_dss_device struct to
configure the DISPC and VENC blocks accordingly. This makes the VENC interface
driver dependent on the omap_dss_device struct.
Make the VENC driver data maintain it's own timings field. The panel driver is
expected to call omapdss_venc_set_timings() to set these timings before the
panel is enabled. Call omapdss_venc_set_timings() before enabling
venc output, this is done to atleast have the venc output configured to the
panel's default timings if the DSS user didn't explicitly call the venc panel
driver's set_timings op.
Make the VENC panel driver configure the new timings is the omap_dss_device
struct(dssdev->panel.timings). The VENC driver is responsible for maintaining
only it's own copy of timings.
Signed-off-by: Archit Taneja <archit@ti.com>
The current venc.c driver contains both the interface and panel driver code.
This makes the driver hard to read, and difficult to understand the work split
between the interface and panel driver and the how the locking works.
This also makes it easier to clearly define the VENC interface ops called by the
panel driver.
Split venc.c into venc.c and venc_panel.c representing the interface and panel
driver respectively. This split is done along the lines of the HDMI interface
and panel drivers.
Signed-off-by: Archit Taneja <archit@ti.com>
The SDI driver currently relies on the timings in omap_dss_device struct to
configure the DISPC accordingly. This makes the SDI interface driver dependent
on the omap_dss_device struct.
Make the SDI driver data maintain it's own timings field. The panel driver is
expected to call omapdss_sdi_set_timings() to set these timings before the panel
is enabled.
Make the SDI panel driver configure the new timings is the omap_dss_device
struct(dssdev->panel.timings). The SDI driver is responsible for maintaining
only it's own copy of timings.
Signed-off-by: Archit Taneja <archit@ti.com>
Create function omapdss_sdi_set_timings(). Configuring new timings is done the
same way as before, SDI is disabled, and re-enabled with the new timings in
dssdev. This just moves the code from the panel drivers to the SDI driver.
The panel drivers shouldn't be aware of how SDI manages to configure a new set
of timings. This should be taken care of by the SDI driver itself.
Signed-off-by: Archit Taneja <archit@ti.com>
The hdmi interface driver exposes functions to the hdmi panel driver to
configure the interface timings maintained by the hdmi driver.
These timings(stored in hdmi.ip_data.cfg) should be protected by the hdmi lock
to ensure they are called sequentially, this is similar to how hdmi enable and
disable functions need locking.
Signed-off-by: Archit Taneja <archit@ti.com>
The hdmi driver currently updates only the 'code' member of hdmi_config when
the op omapdss_hdmi_display_set_timing() is called by the hdmi panel driver.
The 'timing' field of hdmi_config is updated only when hdmi_power_on is called.
It makes more sense to configure the whole hdmi_config field in the set_timing
op called by the panel driver. This way, we don't need to call both functions
to ensure that our hdmi_config is configured correctly. Also, we don't need to
calculate hdmi_config during hdmi_power_on, or rely on the omap_video_timings
in the panel's omap_dss_device struct.
The default timings of the hdmi panel are represented in a cleaner form. Since
the hdmi output is now configured by it's own copy of timings (in
hdmi.ip_data.cfg), the panel driver needs to set it to a valid value before
enabling hdmi output. We now call omapdss_hdmi_set_timing() before enabling
hdmi output, this is done to atleast have the hdmi output configured to the
panel's default timings if the DSS user didn't call panel driver's set_timings()
op explicitly.
Signed-off-by: Archit Taneja <archit@ti.com>
During a command mode update using DISPC video port, we may need to swap the
connected overlay manager's width and height when 90 or 270 degree rotation is
done via the panel by changing it's address mode.
Call dss_mgr_set_timings() in update_screen_dispc() before starting the manager
update. The new manager size is updated in the 'timings' field of DSI driver's
private data via omapdss_dsi_set_size(). A panel driver is expected to call this
when performing rotation.
Signed-off-by: Archit Taneja <archit@ti.com>
DSI command mode panels don't need to configure a full set of timings to
configure DSI, they only require the width and the height of the panel in
pixels.
Use omapdss_dsi_set_size for command mode panels, omapdss_dsi_set_timings is
meant for video mode panels. When performing rotation via chaning the address
mode of the panel, we would need to swap width and height when doing 90 or 270
rotation. Make sure that omapdss_dsi_set_size() makes the new width and height
visible to DSI.
Signed-off-by: Archit Taneja <archit@ti.com>
The DSI driver currently relies on the timings in omap_dss_device struct to
configure the DISPC and DSI blocks accordingly. This makes the DSI interface
driver dependent on the omap_dss_device struct.
Make the DSI driver data maintain it's own timings field. A DSI video mode panel
driver is expected to call omapdss_dsi_set_timings() to set these timings before
the panel is enabled.
Signed-off-by: Archit Taneja <archit@ti.com>
The timings maintained in omap_dss_device(dssdev->panel.timings) should be
maintained by the panel driver itself. It's the panel drivers responsibility
to update it if a new set of timings is to be configured. The DPI interface
driver shouldn't be responsible of updating the panel timings, it's responsible
of maintianing it's own copy of timings.
Signed-off-by: Archit Taneja <archit@ti.com>
The DPI driver currently relies on the timings in omap_dss_device struct to
configure the DISPC accordingly. This makes the DPI interface driver dependent
on the omap_dss_device struct.
Make the DPI driver data maintain it's own timings field. The panel driver is
expected to call dpi_set_timings()(renamed to omapdss_dpi_set_timings) to set
these timings before the panel is enabled.
In the set_timings() op, we still ensure that the omap_dss_device timings
(dssdev->panel.timings) are configured. This will later be configured only by
the DPI panel drivers.
Signed-off-by: Archit Taneja <archit@ti.com>
The generic DPI panel driver doesn't currently have locking to ensure that
the display states and the driver data is maintained correctly. Add mutex
locking to take care of this. Add a new get_timings driver op to override the
default get_timings op. The new driver op contains locking to ensure the correct
panel timings are seen when a DSS2 user calls device->driver->get_timings.
Signed-off-by: Archit Taneja <archit@ti.com>
The DPI interface driver currently relies on the panel driver to ensure calls
like omapdss_dpi_display_enable() and omapdss_dpi_display_disable() are executed
sequentially. Also, currently, there is no way to protect the DPI driver data.
All DPI panel drivers don't ensure this, and in general, a DPI panel driver
should use it's lock to that ensure it's own driver data and omap_dss_device
states are taken care of, and not worry about the DPI interface.
Add mutex locking in the DPI enable/disable/set_timings ops.
Signed-off-by: Archit Taneja <archit@ti.com>
The function dss_mgr_set_timings is supposed to apply timings passed by an
interface driver. It is not supposed to change the timings. Add const qualifier
to the omap_video_timings pointer argument in dss_mgr_set_timings().
Signed-off-by: Archit Taneja <archit@ti.com>
omapfb does not currently set pseudo palette correctly for color depths
above 16bpp, making red text invisible, command like
echo -e '\e[0;31mRED' > /dev/tty1
will display nothing on framebuffer console in 24bpp mode.
This is because temporary variable is declared incorrectly, fix it.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DSS code wrongly assumes that VENC is always available as source for the external
sync signal for the display controller DIGIT channel. One cannot blindly write/read
the value of DSS_CONTROL[15] as in certain processors (e.g., OMAP5) this operation
may not be valid. If the the sync source is not read correctly, the callers of
dss_get_hdmi_venc_clk_source might make wrong assumptions about, for instance,
video timings.
Logic is added to correctly get the sync signal based on the available displays
in the DIGIT channel. The source is set only if both VENC and HDMI are supported.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have no reason to block in the error handler workqueue, so use msleep.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Small patch to disable the PLL appropriately before runtime_put in case
an error occurs while enabling the PHY.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This patch moves the contents from regs-fb-v4.h and regs-fb.h to
include/video/samsung_fimd.h. Also updates the header inclusion in
machine files and driver files accordingly.
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
It includes:
- large updates for OMAP
- support for LCD3 overlay manager (omap5)
- omapdss output cleanup
- removal of passive matrix LCD support as there are no drivers for
such panels for DSS or DSS2 and nobody complained (cleanup)
- large updates for SH Mobile
- overlay support
- separating MERAM (cache) from framebuffer driver
- some updates for Exynos and da8xx-fb
- various other small patches
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=22b7
-----END PGP SIGNATURE-----
Merge tag 'fbdev-updates-for-3.6' of git://github.com/schandinat/linux-2.6
Pull fbdev updates from Florian Tobias Schandinat:
- large updates for OMAP
- support for LCD3 overlay manager (omap5)
- omapdss output cleanup
- removal of passive matrix LCD support as there are no drivers for
such panels for DSS or DSS2 and nobody complained (cleanup)
- large updates for SH Mobile
- overlay support
- separating MERAM (cache) from framebuffer driver
- some updates for Exynos and da8xx-fb
- various other small patches
* tag 'fbdev-updates-for-3.6' of git://github.com/schandinat/linux-2.6: (78 commits)
da8xx-fb: fix compile issue due to missing include
fbdev: Make pixel_to_pat() failure mode more friendly
da8xx-fb: do not turn ON LCD backlight unless LCDC is enabled
fbdev: sh_mobile_lcdc: Fix vertical panning step
video: exynos mipi dsi: Fix mipi dsi regulators handling issue
video: da8xx-fb: do clock reset of revision 2 LCDC before enabling
arm: da850: configure LCDC fifo threshold
video: da8xx-fb: configure FIFO threshold to reduce underflow errors
video: da8xx-fb: fix flicker due to 1 frame delay in updated frame
video: da8xx-fb rev2: fix disabling of palette completion interrupt
da8xx-fb: add missing FB_BLANK operations
video: exynos_dp: use usleep_range instead of delay
video: exynos_dp: check the only INTERLANE_ALIGN_DONE bit during Link Training
fb: epson1355fb: Fix section mismatch
video: exynos_dp: fix wrong DPCD address during Link Training
video/smscufx: fix line counting in fb_write
aty128fb: Fix coding style issues
fbdev: sh_mobile_lcdc: Fix pan offset computation in YUV mode
fbdev: sh_mobile_lcdc: Fix overlay registers update during pan operation
fbdev: sh_mobile_lcdc: Support horizontal panning
...
