Add a couple of supported devices into the help message.
It's a long story... I promised this comment changed to a user long ago,
so I'd like to have that promise kept. In reality though, nobody is
likely to read this anyway.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I'm going to throw schedule_work away, it's retarded. But for starters,
let's have it encapsulated.
Also, generic and whiteheat were both calling usb_serial_port_softint
and scheduled work. Only one was necessary.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clean up the unicode handling in io_edgeport. Make get_string size-limited.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as693b) makes the usbtest driver report errors in the
isochronous bulk transfer tests instead of always returning 0. As an
arbitrary cutoff, an error is returned if more than 10% of the packet
transfers fail. It also stops a test immediately upon receiving an URB
submission error.
For a test harness, it's especially important to report when errors occur!
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as692) fixes a few memory leaks in some unimportant error
pathways of the gadgetfs driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as691) fixes a few errors in the AIO interface for the
gadgetfs driver. Now requests will complete properly instead of hanging.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
By the way I have to ask you to add new (vid,pid) pair to cp2101 driver.
This device is argussoft's avr in-system programmer AS3M,
http://atmel.argussoft.ru/hard.htm
it's based on cp2101 chip and works pretty well with the linux driver.
It could be used with argussoft's `asisp1109.exe'
(http://atmel.argussoft.ru/download/software/as-tools.soft/asisp.zip)
tool run under wine.
Signed-off-by: Vitja Makarov <vitja.makarov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ctrl_complete functions acquires ctx->lock and tries to unlink
all queued urbs in case of errors through usb_unlink_urb func.
In its turn usb_unlink_urb calls, through the hcd driver,
usb_hcd_giveback_urb which calls ctrl_complete again. At this
time, ctx->lock is already taken by the same function.
Signed-off-by: Franck Bui-Huu <vagabon.xyz@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as690) does the same thing for ISO TDs as as680 did for
non-ISO TDs: free them as they are used rather than all at once when an
URB is complete. At the same time it fixes a minor buglet (I'm not
aware of it ever affecting anyone): An ISO TD should be retired when its
frame is over, regardless of whether or not the hardware has marked it
inactive.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as689) stores the period for periodic transfers (interrupt
and ISO) in the queue header. This is necessary for proper bandwidth
tracking (not yet implemented). It also makes the scheduling of ISO
transfers a bit more rigorous, with checks for out-of-bounds frame
numbers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as688) fixes a small race in uhci-hcd. Because ISO queues
aren't controlled by queue headers, they can't be unlinked. Only
individual URBs can. So whenever multiple ISO URBs are dequeued, it's
necessary to make sure the hardware is done with each one. We can't
assume that dequeuing the first URB will suffice to unlink the entire
queue.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as687) changes uhci-hcd to keep track of frame numbers as
full-sized integers rather than 11-bit values. This makes them a lot
easier to handle and makes it possible to schedule beyond a 2-second
window, should anyone ever want to do so.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch increases an arbitrary limit on the size of
individual isochronous packets submitted via usbfs. The
limit is still arbitrary, but it's now large enough to
support the maximum packet size used by high-bandwidth
isochronous transfers.
Signed-off-by: Micah Dowty <micah@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the artificial 4088-byte limit that usbfs
currently places on Control transfers. The USB spec does not
specify a strict limit on the size of an entire control transfer.
It does, however, state that the data stage "follows the same
protocol rules as bulk transfers." (USB 2, 8.5.3)
The level of support for large control transfers in real host
controllers varies, but it's important to support at least 4K
transfers. Windows enforces a maximum control transfer size
of 4K, so there exists some hardware that requires a full 4096
byte data stage. Without this patch, we fall short of that by
8 bytes on architectures with a 4K page size, and it becomes
impossible to support such hardware with a user-space driver.
Since any limit placed on control transfers by usbfs would be
arbitrary, this patch replaces the PAGE_SIZE limit with the same
arbitrary limit used by bulk transfers.
Signed-off-by: Micah Dowty <micah@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some old Intel UHCI controllers have a bug that has shown up in a few
systems (the PIIX3 "Neptune" chip set). Until now there has not been
any simple way to work around the bug, but the lastest changes in
uhci-hcd have made it easy. This patch (as684) adds the work-around.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as683) re-implements Full-Speed Bandwidth Reclamation (FSBR)
properly. It keeps track of which endpoint queues have advanced, and
when none have advanced for a sufficiently long time, FSBR is turned
off. The next TD on each of the non-moving queues is modified to
generate an interrupt on completion, so that FSBR can be re-enabled as
soon as the hardware starts to make some progress.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as682) gets rid of the TD-removal list in uhci-hcd. It is
no longer needed because now TDs are not freed until we know the
hardware isn't using them. It also simplifies the code for adding and
removing TDs to/from URBs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as681) moves some code for cleaning up after unlinked URBs
out of the general completion pathway into the unlinking pathway.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as680) frees non-isochronous TDs as they are used, rather
than all at once when an URB is complete. Although not a terribly
important change in itself, it opens the door to a later enhancement
that will reduce storage requirements by allocating only a limited
number of TDs at any time for each endpoint queue.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as679) combines the result routine for Control URBs with the
routine for Bulk/Interrupt URBs. Along the way I eliminated the
debugging printouts for Control transfers unless the debugging level is
set higher than 1. I also eliminated a long-unused (#ifdef'ed-out)
section that works around some buggy old APC BackUPS devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It seems to be relatively common for USB keyboards and mice to dislike
being polled for reports. Since there's no need to poll a keyboard or
a mouse, this patch (as685) automatically sets the HID_QUIRK_NOGET flag
for devices that advertise themselves as either sort of device with boot
protocol support.
This won't cure all the problems since some devices don't support the
boot protocol, but it's simple and easy and it should fix quite a few
problems.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Transposed lines of code in drivers/usb/input/hid-input.c causes the
capability bits for a new HID device to be set before quirks are applied
at configuration time. When an HID event is then sent up to the input
layer, it may then be discarded as irrelevant because the wrong
capability bit is set.
Further, the quirks for the Apple Mighty Mouse are not quite right: the
horizontal scrolling needs its axis reversed, and the left and center
buttons are transposed. Also, the mouse is labeled in the kernel with
its earlier name (I think) of Apple PowerMouse.
Steps to reproduce problem: Plug in an Apple Mighty Mouse. Note that
horizontal scrolling doesn't work at all, and in fact doesn't generate
any input events on /dev/input/eventN. Note also that pushing the
middle button performs the right button action, and vice versa. Once
you have the horizontal scrolling working, note that it is backward WRT
both to vertical scrolling and to common sense.
This patch maybe should be broken up, as it does address two problems.
The transposed code in hidinput_configure_usage() probably creates bugs
beyond just the Mighty Mouse. The rest of the patch renames POWERMOUSE
to MIGHTYMOUSE everywhere (which I *believe* is correct), fixes the
MIGHTYMOUSE quirk to swap the center and right mouse buttons, and adds a
new quirk HID_QUIRK_INVERT_HWHEEL also assigned to the MIGHTYMOUSE with
code in hidinput_hid_event() to implement it.
Signed-off-by: Bart Massey <bart@cs.pdx.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as676) fixes a small bug in uhci-hcd's enqueue routine. When
an URB is unlinked or gets an error and the completion handler queues
another URB for the same endpoint, the queue shouldn't be allowed to start
up again until the handler returns. Not even if the new URB is the only
one on its queue.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as675) simplifies uhci-hcd slightly by storing each endpoint's
type in the corresponding Queue Header structure.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The net2280 board has an annoying habit of surviving soft reboots with
interrupts enabled. This patch (as674) adds a shutdown routine to the
driver so that the board can be put in a quiescent state.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unfortunately it looks like the transport entry for this subdriver was merged
into the protocol section, making this driver unusable :(
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After some further testing with my flash device I realised that our current
probe doesn't always work (e.g. when no media is inserted).
Now that Peter Chubb's patch has simplified the detection of 99% of the HP CD
writers out there, we have a much smaller range of hardware to work with on
the shared device ID, so it should be possible to try some of the previous
probe options again: we just need to find another tester with a USBAT2-based HP
CD writer.
This patch hardcodes the flash detection until someone comes along with one of
these obscure CD drives. Note that these devices are extremely rare, so even if
we can't ever find a decent probe method, at least we will be supporting almost
all of the USBAT-based hardware out there.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use USB vendor and product IDs to determine whether the attached
device is a CDROM or a Flash device. Daniel Drake says that the
*same* vendor and product IDs for non-HP vendor ID could be either
flash or cdrom, so try to probe for them.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've worked out what's going wrong. The scsi layer is now much
more likely to pass down scatterlists instead of plain buffers. So
you have to make sure that they're handled correctly. In one of the
changes along the way, usbat_write_block and friends stopped obeying
the srb->use_sg flag.
Anyway, with the appended patch, and the one I'm putting in the next email, it
all seems to work for the HP cd4e. Of course, someone's going to have
to test it with the flash drives as well....
This patch teaches the usbat_{read,write}_block functions to
obey the use_sg flag in the scsi-request.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make inputs pollable using sysfs_notify and add support for the Phidget
InterfaceKit 0/16/16. Various cleanups.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Daniel Saakes <daniel@saakes.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We #include <linux/netdevice.h> only because <linux/etherdevice.h>
needed it, but didn't #include it itself. But that's been fixed now.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the check for NULL which makes no sense. Suggested by Al.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some hubs claim not to support port-power switching, and right now the
hub driver believes them and does not enable power to their ports.
However it turns out that even though they don't actually switch power,
they do ignore all events on a port until told to turn on the power!
This problem has been reported by several users.
This revised patch (as672b) makes the hub driver always try to turn on
port power to all hubs, regardless of what the hub descriptor says. It
also adds a comment explaining the need for this.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for MacBook touchpad in appletouch driver.
Thanks to Alex Harper for the informations.
Use u16 instead of int16_t in atp_is_geyser* functions.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Prevent sending further output to a USB-serial console after the dongle is
disconnected, take care not to leak kref.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Prevent ENODEV on a /dev/ttyUSBx, used as a USB-serial console.
From: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Prevent NULL dereference when used as a USB-serial console.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Append Carriage-Returns after Line-Feeds, analogous to the serial driver.
From: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In some systems we may have both a platform EHCI controller and PCI EHCI
controller. Previously we couldn't build the EHCI support as a module due
to conflicting module_init() calls in the code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains the following possible cleanups:
- make needlessly global functions static
- function and struct declarations belong into header files
- make SiS_VCLKData const
- #if 0 the following unused global functions:
- sisusb.c: sisusb_writew()
- sisusb.c: sisusb_readw()
- sisusb_init.c: SiSUSB_GetModeID()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
From: Arjan van de Ven <arjan@infradead.org>
Convert the semaphores-used-as-mutex to mutexes in the sisusb video driver;
this required manual checking due to the "return as locked" stuff in this
driver, but the ->lock semaphore is still used as mutex in the end.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Cc: Thomas Winischhofer <winischhofer.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for detection and dworking with a ASIX 88178 based USB-Gigabit
adaptor. With the patch, it is detected and handled correctly by the asix
module.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This includes an MTU fixup which could affect larger packets with newer
Zaurii, described as http://bugzilla.kernel.org/show_bug.cgi?id=6286;
plus minor whitespace cleanup.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this fixes the "duplicated text" bug. There's a modem that cannot cope
with large transfers and more than one urb in flight. This patch adds a
special case to the driver.
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Keys on Yealink based phones will not function properly when using the
generic HID driver. This patch prevents the generic HID code from
grabbing the device before the regular yealink driver can get a grip on
it.
Signed-off-by: Henk Vergonet <Henk.Vergonet@gmail.com>
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
From: Paul Serice <paul@serice.net>
The workaround in commit f7201c3dcd
broke. The work around requires memory for DMA transfers for some
NVidia EHCI controllers to be below 2GB, but recent changes have
caused some DMA memory to be allocated before the DMA mask is set.
Signed-off-by: Paul Serice <paul@serice.net>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During the recent "isa drivers using platform devices" discussion it was
pointed out that (ALSA) ISA drivers ran into the problem of not having
the option to fail driver load (device registration rather) upon not
finding their hardware due to a probe() error not being passed up
through the driver model. In the course of that, I suggested a seperate
ISA bus might be best; Russell King agreed and suggested this bus could
use the .match() method for the actual device discovery.
The attached does this. For this old non (generically) discoverable ISA
hardware only the driver itself can do discovery so as a difference with
the platform_bus, this isa_bus also distributes match() up to the driver.
As another difference: these devices only exist in the driver model due
to the driver creating them because it might want to drive them, meaning
that all device creation has been made internal as well.
The usage model this provides is nice, and has been acked from the ALSA
side by Takashi Iwai and Jaroslav Kysela. The ALSA driver module_init's
now (for oldisa-only drivers) become:
static int __init alsa_card_foo_init(void)
{
return isa_register_driver(&snd_foo_isa_driver, SNDRV_CARDS);
}
static void __exit alsa_card_foo_exit(void)
{
isa_unregister_driver(&snd_foo_isa_driver);
}
Quite like the other bus models therefore. This removes a lot of
duplicated init code from the ALSA ISA drivers.
The passed in isa_driver struct is the regular driver struct embedding a
struct device_driver, the normal probe/remove/shutdown/suspend/resume
callbacks, and as indicated that .match callback.
The "SNDRV_CARDS" you see being passed in is a "unsigned int ndev"
parameter, indicating how many devices to create and call our methods with.
The platform_driver callbacks are called with a platform_device param;
the isa_driver callbacks are being called with a "struct device *dev,
unsigned int id" pair directly -- with the device creation completely
internal to the bus it's much cleaner to not leak isa_dev's by passing
them in at all. The id is the only thing we ever want other then the
struct device * anyways, and it makes for nicer code in the callbacks as
well.
With this additional .match() callback ISA drivers have all options. If
ALSA would want to keep the old non-load behaviour, it could stick all
of the old .probe in .match, which would only keep them registered after
everything was found to be present and accounted for. If it wanted the
behaviour of always loading as it inadvertently did for a bit after the
changeover to platform devices, it could just not provide a .match() and
do everything in .probe() as before.
If it, as Takashi Iwai already suggested earlier as a way of following
the model from saner buses more closely, wants to load when a later bind
could conceivably succeed, it could use .match() for the prerequisites
(such as checking the user wants the card enabled and that port/irq/dma
values have been passed in) and .probe() for everything else. This is
the nicest model.
To the code...
This exports only two functions; isa_{,un}register_driver().
isa_register_driver() register's the struct device_driver, and then
loops over the passed in ndev creating devices and registering them.
This causes the bus match method to be called for them, which is:
int isa_bus_match(struct device *dev, struct device_driver *driver)
{
struct isa_driver *isa_driver = to_isa_driver(driver);
if (dev->platform_data == isa_driver) {
if (!isa_driver->match ||
isa_driver->match(dev, to_isa_dev(dev)->id))
return 1;
dev->platform_data = NULL;
}
return 0;
}
The first thing this does is check if this device is in fact one of this
driver's devices by seeing if the device's platform_data pointer is set
to this driver. Platform devices compare strings, but we don't need to
do that with everything being internal, so isa_register_driver() abuses
dev->platform_data as a isa_driver pointer which we can then check here.
I believe platform_data is available for this, but if rather not, moving
the isa_driver pointer to the private struct isa_dev is ofcourse fine as
well.
Then, if the the driver did not provide a .match, it matches. If it did,
the driver match() method is called to determine a match.
If it did _not_ match, dev->platform_data is reset to indicate this to
isa_register_driver which can then unregister the device again.
If during all this, there's any error, or no devices matched at all
everything is backed out again and the error, or -ENODEV, is returned.
isa_unregister_driver() just unregisters the matched devices and the
driver itself.
More global points/questions...
- I'm introducing include/linux/isa.h. It was available but is ofcourse
a somewhat generic name. Moving more isa stuff over to it in time is
ofcourse fine, so can I have it please? :)
- I'm using device_initcall() and added the isa.o (dependent on
CONFIG_ISA) after the base driver model things in the Makefile. Will
this do, or I really need to stick it in drivers/base/init.c, inside
#ifdef CONFIG_ISA? It's working fine.
Lastly -- I also looked, a bit, into integrating with PnP. "Old ISA"
could be another pnp_protocol, but this does not seem to be a good
match, largely due to the same reason platform_devices weren't -- the
devices do not have a life of their own outside the driver, meaning the
pnp_protocol {get,set}_resources callbacks would need to callback into
driver -- which again means you first need to _have_ that driver. Even
if there's clean way around that, you only end up inventing fake but
valid-form PnP IDs and generally catering to the PnP layer without any
practical advantages over this very simple isa_bus. The thing I also
suggested earlier about the user echoing values into /sys to set up the
hardware from userspace first is... well, cute, but a horrible idea from
a user standpoint.
Comments ofcourse appreciated. Hope it's okay. As said, the usage model
is nice at least.
Signed-off-by: Rene Herman <rene.herman@keyaccess.nl>
This patch (as721) makes dev_info and related macros print the device's
bus name if the device doesn't have a driver, instead of printing just a
blank. If the device isn't on a bus either... well, then it does leave
a blank space. But it will be easier for someone else to change if they
want.
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to create the "compatible" symlinks that class_devices used to
create when they were in the class directories so that userspace does
not know anything changed at all.
Yeah, we have a lot of symlinks now, but we should be able to get rid of
them in a year or two... (wishful thinking...)
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Like the SUBSYTEM= key we find in the environment of the uevent, this
creates a generic "subsystem" link in sysfs for every device. Userspace
usually doesn't care at all if its a "class" or a "bus" device. This
provides an unified way to determine the subsytem of a device, regardless
of the way the driver core has created it.
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the first step in moving class_device to being replaced by
struct device. It allows struct device to export a dev_t and makes it
easy to dynamically create and destroy struct device as long as they are
associated with a specific class.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed for a future patch for the device code to create the
proper symlinks for devices that are "class devices".
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hi, this patch converts semaphores to mutexes for Randy's firmware_class.
Signed-off-by: Laura Garcia Liebana <nevola@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes the driver model PM suspend debug messages more useful, by
(a) explaining what event is being sent, since not all suspend()
requests mean the same thing;
(b) reporting when a PM_EVENT_SUSPEND call is allowing the device
to issue wakeup events.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To have a home for all hypervisors, this patch creates /sys/hypervisor.
A new config option SYS_HYPERVISOR is introduced, which should to be set
by architecture dependent hypervisors (e.g. s390 or Xen).
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
platform_device_add() should be using device_add() rather
than device_register() - any platform device passed to
platform_device_add() should have already been initialised,
either by platform_device_alloc() or platform_device_register().
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
allow sysdev_class adding attribute. Next patch will use the new API to
add an attribute under /sys/device/system/cpu/.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds modalias support to platform devices, for simpler
hotplug/coldplug driven driver setup.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The drivers/base/power PM debug messages should appear when
either PM or driver model debug are enabled.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
class_device_add needs to check the return value of all the setup it
does. It doesn't handle out of memory well. This is not complete, probably
more needs to be done.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Using the class device pointer returned by tty_register_device() with
part 1 of the patch, attach the Gigaset drivers' "cidmode" sysfs entry
to its tty class device, where it can be found more easily by users
who do not know nor care which USB port the device is attached to.
Signed-off-by: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Let tty_register_device() return a pointer to the class device it creates.
This allows registrants to add their own sysfs files under the class
device node.
Signed-off-by: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
split bus_add_device() and send device uevents after sysfs population
Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The nVidia CK804 PCI-E chipset supports the AER extended capability
but sometimes fails to link it (with some BIOS or after a warm reboot).
It makes the AER cap invisible to pci_find_ext_capability().
The patch adds a quirk to set the missing bit that controls the
linking of the capability.
By the way, it removes the corresponding code in the myri10ge driver.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Loic Prylli <loic@myri.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
From: Doug Thompson <norsk5@yahoo.com>
This patch adds the 'broken_parity_status' sysfs attribute file to a PCI device.
Reading this attribute a userland program can determine if PCI device provides false
positives (value of 1) in its generation of PCI Parity status, or not (value of 0).
As PCI devices are found to be 'bad' in this regard, userland programs can also set
the appropriate value (root access only) of a faulty device. This per device
information will be used in the EDAC PCI Parity scanner code in a future patch once
this interface becomes available.
Signed-off-by: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Be more selective when running the MSI-K8T-Neo2Fir soundcard PCI quirk so
as not to run this on hardware where it's probably not needed.
Signed-off-by: Chris Wedgwood <cw@f00f.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pci_walk_bus has a race with pci_destroy_dev. When cb is called
in pci_walk_bus, pci_destroy_dev might unlink the dev pointed by next.
Later on in the next loop, pointer next becomes NULL and cause
kernel panic.
Below patch against 2.6.17-rc4 fixes it by changing pci_bus_lock (spin_lock)
to pci_bus_sem (rw_semaphore).
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The code is really not needed.
Roland Dreier/Greg KH removed the release_mem_region() calls that
were the only consumers of phys_addr:
http://www.ussg.iu.edu/hypermail/linux/kernel/0503.0/1540.html
patch below deletes the "dead" code.
Signed-off-by: Grant Grundler <iod00d@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A recent Stratus x86_64 platform uses a system ioapic that is a PCI device
located below a PCI bridge. Other platforms like this may exist.
This patch fixes a problem wherein the kernel's PCI setup code moves
the ioapic to an address other than that assigned by the BIOS. It simply
adds another exclusion (which already includes classless devices and host
bridges) to the function pbus_assign_resources_sorted so that it will not
move the ioapic.
If the ioapic is moved, the fixmap mapping to it is broken, so the OS should
leave it alone.
From: Kimball Murray <kimball.murray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In IA64 platform, msi driver does not use irq_vector variable, and in
x86 platform LAST_DEVICE_VECTOR should one before FIRST_SYSTEM_VECTOR,
this patch modify this.
Signed-off-by: bibo, mao <bibo.mao@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Brice said the pci_save_msi_state breaks his driver in his special usage
(not in suspend/resume), as pci_save_msi_state will disable msi mode. In
his usage, pci_save_state will be called at runtime, and later (after
the device operates for some time and has an error) pci_restore_state
will be called.
In another hand, suspend/resume needs disable msi mode, as device should
stop working completely. This patch try to workaround this issue.
Drivers are expected call pci_disable_device in suspend time after
pci_save_state.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We recently ran into a problem where the e1000 device failed to
work properly on the kexec kernel. MSI was enabled for the
device in the main kernel when it crashed. The e1000 driver
tried to enable MSI on the kexec kernel, but the code bailed
early when it found that MSI was already enabled in the hardware,
even though the software state was not properly set up in the
kexec'd kernel. This patch fixes the problem by moving the
early return to after making sure that the software state
is properly initialized.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PCI_BUS_FLAGS_NO_MSI bus flags does not appear do be inherited
correctly from the amd8131 MSI quirk to its parent busses. It makes
devices behind a bridge behind amd8131 try to enable MSI while the
amd8131 does not support it.
We fix this by looking at flags of all parent busses in
pci_enable_msi() and pci_enable_msix().
By the way, also add the missing dev->no_msi check in pci_enable_msix()
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, the EDAC (error detection and correction) modules that are in
the kernel contain some features that need to be moved. After some good
feedback on the PCI Parity detection code and interface
(http://www.ussg.iu.edu/hypermail/linux/kernel/0603.1/0897.html) this
patch ADDs an new attribute to the pci_dev structure: Namely the
'broken_parity_status' bit.
When set this indicates that the respective hardware generates false
positives of Parity errors.
The EDAC "blacklist" solution was inferior and will be removed in a
future patch.
Also in this patch is a PCI quirk.c entry for an Infiniband PCI-X card
which generates false positive parity errors.
I am requesting comments on this AND on the possibility of a exposing
this 'broken_parity_status' bit to userland via the PCI device sysfs
directory for devices. This access would allow for enabling of this
feature on new devices and for old devices that have their drivers
updated. (SLES 9 SP3 did this on an ATI motherboard video device). There
is a need to update such a PCI attribute between kernel releases.
This patch just adds a storage place for the attribute and a quirk entry
for a known bad PCI device. PCI Parity reaper/harvestor operations are
in EDAC itself and will be refactored to use this PCI attribute instead
of its own mechanisms (which are currently disabled) in the future.
Signed-off-by: Doug Thompson <norsk5@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There were two instances of pci_acpi_init(), one in
drivers/pci/pci-acpi.c and another in arch/i386/pci/acpi.c.
Rename the one in pci-acpi.c and make it consistent with
other names in the same file.
Signed-off-by: Muthukumar R <muthur@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a device is already enabled, don't bother reenabling it.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Acked-By: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an "enable" sysfs attribute to each PCI device. When read it
shows the "enabled-ness" of the device, but you can write a "0" into it to
disable a device, and a "1" to enable it.
This later is needed for X and other cases where userspace wants to enable
the BARs on a device (typical example: to run the video bios on a secundary
head). Right now X does all this "by hand" via bitbanging, that's just evil.
This allows X to no longer do that but to just let the kernel do this.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
CC: Peter Jones <pjones@redhat.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI: Add pci_assign_resource_fixed -- allow fixed address assignments
On some embedded systems the PCI address for hotplug devices are not only
known a priori but are required to be at a given PCI address for other
master in the system to be able to access.
An example of such a system would be an FPGA which is setup from user space
after the system has booted. The FPGA may be access by DSPs in the system
and those DSPs expect the FPGA at a fixed PCI address.
Added pci_assign_resource_fixed() as a way to allow assignment of the PCI
devices's BARs at fixed PCI addresses.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we detect a 64-bit pre-set address in a BAR on a 32-bit platform,
we disable it and treat it as if it had been unset, thus allowing the
general address assignment code to assign a new address to it when the
device is enabled. This can happen either if the firmware assigns
64-bit addresses; additionally, some cards have been found "in the
wild" which do not come out of reset with all the BAR registers set to
zero.
Unfortunately, the patch that implemented this tested the low part of
the address instead of the high part of the address. This patch fixes
that.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[pci] Ignore pre-set 64-bit BARs on 32-bit platforms
Currently, Linux always rejects a device which has a pre-set 64-bit
address on a 32-bit platform. On systems which do not do PCI
initialization in firmware, this causes some devices which don't
correctly power up with all BARs zero to fail.
This patch makes the kernel automatically zero out such an address
(thus treating it as if it had not been set at all, meaning it will
assign an address if necessary).
I have done this only for devices, not bridges. It seems potentially
hazardous to do for bridges.
Signed-off-by: H. Peter Anvin <hpa@c2micro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MSI callouts for altix. Involves a fair amount of code reorg in sn irq.c
code as well as adding some extensions to the altix PCI provider abstaction.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Abstract IA64_FIRST_DEVICE_VECTOR/IA64_LAST_DEVICE_VECTOR since SN platforms
use a subset of the IA64 range. Implement this by making the above macros
global variables which the platform can override in it setup code.
Also add a reserve_irq_vector() routine used by SN to mark a vector's as
in-use when that weren't allocated through assign_irq_vector().
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Abstract portions of the MSI core for platforms that do not use standard
APIC interrupt controllers. This is implemented through a new arch-specific
msi setup routine, and a set of msi ops which can be set on a per platform
basis.
Signed-off-by: Mark Maule <maule@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Creates new config variables PPC_CELL_NATIVE and PPC_IBM_CELL_BLADE.
The existing CONFIG_PPC_CELL is now used to denote the generic
Cell processor support.
PPC_CELL = make descends into platforms/cell
PPC_CELL_NATIVE = add bare metal support
PPC_IBM_CELL_BLADE = add blade device drivers, etc.
Also renames spu_priv1.c to spu_priv1_mmio.c.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The same I2C driver found on 85xx, etc., can be used for 86xx too.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bcollins/linux1394-2.6: (28 commits)
eth1394: replace __constant_htons by htons
ieee1394: adjust code formatting in highlevel.c
ieee1394: hl_irqs_lock is taken in hardware interrupt context
ieee1394_core: switch to kthread API
ieee1394: sbp2: Kconfig fix
ieee1394: add preprocessor constant for invalid csr address
sbp2: fix deregistration of status fifo address space
[PATCH] eth1394: endian fixes
Fix broken suspend/resume in ohci1394
sbp2: use __attribute__((packed)) for on-the-wire structures
sbp2: provide helptext for CONFIG_IEEE1394_SBP2_PHYS_DMA and mark it experimental
Update feature removal of obsolete raw1394 ISO requests.
sbp2: fix S800 transfers if phys_dma is off
sbp2: remove ohci1394 specific constant
ohci1394: make phys_dma parameter read-only
ohci1394: set address range properties
ieee1394: extend lowlevel API for address range properties
sbp2: log number of supported concurrent logins
sbp2: remove manipulation of inquiry response
ieee1394: save RAM by using a single tlabel for broadcast transactions
...
There has been an update to the forcedeth driver that added a few new
uses of xmit_lock which is no longer meant to be used directly. This
patch replaces them with netif_tx_lock_bh.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'rio.b19' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/bird:
[PATCH] missing readb/readw in rio
[PATCH] copy_to_user() from iomem is a bad thing
[PATCH] forgotten swap of copyout() arguments
[PATCH] handling rio MEMDUMP
[PATCH] fix rio_copy_to_card() for OLDPCI case
[PATCH] uses of ->Copy() in rioroute are bogus
[PATCH] bogus order of copy_from_user() arguments
[PATCH] rio ->Copy() expects the sourse as first argument
[PATCH] trivial annotations in rio
* git://git.infradead.org/hdrcleanup-2.6: (63 commits)
[S390] __FD_foo definitions.
Switch to __s32 types in joystick.h instead of C99 types for consistency.
Add <sys/types.h> to headers included for userspace in <linux/input.h>
Move inclusion of <linux/compat.h> out of user scope in asm-x86_64/mtrr.h
Remove struct fddi_statistics from user view in <linux/if_fddi.h>
Move user-visible parts of drivers/s390/crypto/z90crypt.h to include/asm-s390
Revert include/media changes: Mauro says those ioctls are only used in-kernel(!)
Include <linux/types.h> and use __uXX types in <linux/cramfs_fs.h>
Use __uXX types in <linux/i2o_dev.h>, include <linux/ioctl.h> too
Remove private struct dx_hash_info from public view in <linux/ext3_fs.h>
Include <linux/types.h> and use __uXX types in <linux/affs_hardblocks.h>
Use __uXX types in <linux/divert.h> for struct divert_blk et al.
Use __u32 for elf_addr_t in <asm-powerpc/elf.h>, not u32. It's user-visible.
Remove PPP_FCS from user view in <linux/ppp_defs.h>, remove __P mess entirely
Use __uXX types in user-visible structures in <linux/nbd.h>
Don't use 'u32' in user-visible struct ip_conntrack_old_tuple.
Use __uXX types for S390 DASD volume label definitions which are user-visible
S390 BIODASDREADCMB ioctl should use __u64 not u64 type.
Remove unneeded inclusion of <linux/time.h> from <linux/ufs_fs.h>
Fix private integer types used in V4L2 ioctls.
...
Manually resolve conflict in include/linux/mtd/physmap.h
* git://git.infradead.org/mtd-2.6: (199 commits)
[MTD] NAND: Fix breakage all over the place
[PATCH] NAND: fix remaining OOB length calculation
[MTD] NAND Fixup NDFC merge brokeness
[MTD NAND] S3C2410 driver cleanup
[MTD NAND] s3c24x0 board: Fix clock handling, ensure proper initialisation.
[JFFS2] Check CRC32 on dirent and data nodes each time they're read
[JFFS2] When retiring nextblock, allocate a node_ref for the wasted space
[JFFS2] Mark XATTR support as experimental, for now
[JFFS2] Don't trust node headers before the CRC is checked.
[MTD] Restore MTD_ROM and MTD_RAM types
[MTD] assume mtd->writesize is 1 for NOR flashes
[MTD NAND] Fix s3c2410 NAND driver so it at least _looks_ like it compiles
[MTD] Prepare physmap for 64-bit-resources
[JFFS2] Fix more breakage caused by janitorial meddling.
[JFFS2] Remove stray __exit from jffs2_compressors_exit()
[MTD] Allow alternate JFFS2 mount variant for root filesystem.
[MTD] Disconnect struct mtd_info from ABI
[MTD] replace MTD_RAM with MTD_GENERIC_TYPE
[MTD] replace MTD_ROM with MTD_GENERIC_TYPE
[MTD] remove a forgotten MTD_XIP
...
* master.kernel.org:/home/rmk/linux-2.6-arm: (22 commits)
[ARM] 3559/1: S3C2442: core and serial port
[ARM] 3557/1: S3C24XX: centralise and cleanup uart registration
[ARM] 3558/1: SMDK24XX: LED platform devices
[ARM] 3534/1: add spi support to lubbock platform
[ARM] 3554/1: ARM: Fix dyntick locking
[ARM] 3553/1: S3C24XX: earlier print of cpu idcode info
[ARM] 3552/1: S3C24XX: Move VA of GPIO for low-level debug
[ARM] 3551/1: S3C24XX: PM code failes to compile with CONFIG_DCACHE_WRITETHROUGH
[ARM] 3550/1: OSIRIS: fix serial port map for 1:1
[ARM] 3548/1: Fix the ARMv6 CPU id in compressed/head.S
[ARM] 3335/1: Old-abi Thumb sys_syscall broken
[ARM] 3467/1: [3/3] Support for Philips PNX4008 platform: defconfig
[ARM] 3466/1: [2/3] Support for Philips PNX4008 platform: chip support
[ARM] 3465/1: [1/3] Support for Philips PNX4008 platform: headers
[ARM] 3407/1: lpd7x: documetation update
[ARM] 3406/1: lpd7x: compilation fix for smc91x
[ARM] 3405/1: lpd7a40x: CPLD ssp driver
[ARM] 3404/1: lpd7a40x: AMBA CLCD support
[ARM] 3403/1: lpd7a40x: updated default configurations
[ARM] 3402/1: lpd7a40x: serial driver bug fix
...
Following problems are addressed:
- wrong status caused early break out of nand_wait()
- removed the bogus status check in nand_wait() which
is a relict of the abandoned support for interrupted
erase.
- status check moved to the correct place in read_oob
- oob support for syndrom based ecc with strange layouts
- use given offset in the AUTOOOB based oob operations
Partially based on a patch from Vitaly Vool <vwool@ru.mvista.com>
Thanks to Savin Zlobec <savin@epico.si> for tracking down the
status problem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In nand_read_page_syndrome/nand_write_page_syndrome the calculation of
the remaining oob length which is not used by the prepad/ecc/postpad
areas is wrong.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Patch from Lennert Buytenhek
The cirrus ep93xx has 3 pl010 UARTs, while amba-pl010.c only allows
for 2 by default. A while ago, I think we agreed on changing the 2
to 8, but I don't see this in 2.6.17 yet.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds netpoll support for things like netconsole/kgdboe to the s2io
10GbE driver.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This ugly hack was long overdue to die.
It was a way to print out Sparc interrupts in a more freindly format,
since IRQ numbers were arbitrary opaque 32-bit integers which vectored
into PIL levels. These 32-bit integers were not necessarily in the
0-->NR_IRQS range, but the PILs they vectored to were.
The idea now is that we will increase NR_IRQS a little bit and use a
virtual<-->real IRQ number mapping scheme similar to PowerPC.
That makes this IRQ printing hack irrelevant, and furthermore only a
handful of drivers actually used __irq_itoa() making it even less
useful.
Signed-off-by: David S. Miller <davem@davemloft.net>
Attached patch declares connector init function as subsys_init()
and returns -EAGAIN in case connector is not initialized yet.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (51 commits)
[MIPS] Make timer interrupt frequency configurable from kconfig.
[MIPS] Correct HAL2 Kconfig description
[MIPS] Fix R4K cache macro names
[MIPS] Add Missing R4K Cache Macros to IP27 & IP32
[MIPS] Support for the RM9000-based Basler eXcite smart camera platform.
[MIPS] Support for the R5500-based NEC EMMA2RH Mark-eins board
[MIPS] Support SNI RM200C SNI in big endian mode and R5000 processors.
[MIPS] SN: include asm/sn/types.h for nasid_t.
[MIPS] Random fixes for sb1250
[MIPS] Fix bcm1480 compile
[MIPS] Remove support for NEC DDB5476.
[MIPS] Remove support for NEC DDB5074.
[MIPS] Cleanup memory managment initialization.
[MIPS] SN: Declare bridge_pci_ops.
[MIPS] Remove unused function alloc_pci_controller.
[MIPS] IP27: Extract pci_ops into separate file.
[MIPS] IP27: Use symbolic constants instead of magic numbers.
[MIPS] vr41xx: remove unnecessay items from vr41xx/Kconfig.
[MIPS] IP27: Cleanup N/M mode configuration.
[MIPS] IP27: Throw away old unused hacks.
...
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (109 commits)
[ETHTOOL]: Fix UFO typo
[SCTP]: Fix persistent slowdown in sctp when a gap ack consumes rx buffer.
[SCTP]: Send only 1 window update SACK per message.
[SCTP]: Don't do CRC32C checksum over loopback.
[SCTP] Reset rtt_in_progress for the chunk when processing its sack.
[SCTP]: Reject sctp packets with broadcast addresses.
[SCTP]: Limit association max_retrans setting in setsockopt.
[PFKEYV2]: Fix inconsistent typing in struct sadb_x_kmprivate.
[IPV6]: Sum real space for RTAs.
[IRDA]: Use put_unaligned() in irlmp_do_discovery().
[BRIDGE]: Add support for NETIF_F_HW_CSUM devices
[NET]: Add NETIF_F_GEN_CSUM and NETIF_F_ALL_CSUM
[TG3]: Convert to non-LLTX
[TG3]: Remove unnecessary tx_lock
[TCP]: Add tcp_slow_start_after_idle sysctl.
[BNX2]: Update version and reldate
[BNX2]: Use CPU native page size
[BNX2]: Use compressed firmware
[BNX2]: Add firmware decompression
[BNX2]: Allow WoL settings on new 5708 chips
...
Manual fixup for conflict in drivers/net/tulip/winbond-840.c
* 'i915fb' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/intelfb-2.6: (25 commits)
intelfb: fixup clock calculation debugging.
Removed hard coded EDID buffer size.
intelfb: use regular modedb table instead of VESA
intelfb: use firmware EDID for mode database
Revert "intelfb driver -- use the regular modedb table instead of the VESA"
intelfb: int option fix
sync modesetting code with X.org
intelfb: align with changes from my X driver.
intelfb driver -- use the regular modedb table instead of the VESA
Adds support for 256MB aperture on 945 chipsets to the intelfb driver
intelfb -- uses stride alignment of 64 on the 9xx chipsets.
intelfb: some cleanups for intelfbhw
intelfb: fixup pitch calculation like X does
intelfb: fixup p calculation
This patch makes a needlessly global struct static.
intelfb: add i945GM support
intelfb: fixup whitespace..
intelfb: add hw cursor support for i9xx
intelfb: make i915 modeset
intelfb: add support for i945G
...
According to the ACPI spec, it should be enabled on return from suspend,
but bugs happen. Apparently especially on the Apple Intel Macs.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Doing a full ata_busy_sleep() seems to get suspend and resume working
fine on the Apple Mac Mini, at least.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This one's quite tricky. The 53c700 uses the now deprecated fields of
the command structure for saving the prior command when it does
autosense. To fix this, we have to add extra fields to the LUN to
accommodate a copy of the real command.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Updates:
- don't bypass SYNCHRONIZE_CACHE command
- return SCSI_MLQUEUE_HOST_BUSY when no free request slots
- move scsi_remove_host() to the begin of hpt_remove(), or it will
not work after resources being released.
Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn
Spelling correction, orphaned comment removal & update branch name.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received From Mark Salyzyn
Some of the cards product names changed.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove checks for value, since the hotplug core always provides
a valid value.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current SHPCHP driver shows device number of slots in info messages,
but it is useless and should be replaced with slot name.
This patch replaces the device number shown in the info messages with
the slot name.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes unused hpc_event_lock. This patch has no functional
change.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up the interrupt polling timer code in
shpchp_hpc.c. This has no functional changes.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up the code related to issuing SHPC commands. This
patch has no functional changes.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up the interrupt handler of shpchp driver. This
patch has no functional changes.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements .get_address callback of hotplug_slot_ops for
PCIEHP driver. With this patch, we can see bus address of hotplug
slots as follows:
# cat /sys/bus/pci/slots/0010_0000/address
0000:0a:00
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch replaces pci_find_slot() with pci_get_slot() in PCIEHP
driver. This patch enables PCI Express Hotplug on the system which has
multiple PCI domains.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a repost of a patch submitted by Prarit Bhargava on 01-19-06 that
never got integrated.
The get_power_status function is currently reporting a bitwise mapping of
the slot if the slot is powered on. It should return 1 if powered on and
0 if powered off.
Signed-off-by: Mike Habeck <habeck@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The workqueue thread of shpchp driver should be created only when SHPC
based hotplug slots are detected on the system.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Global SERR and Interrupt should be masked at shpchp driver unload time.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current SHPCHP driver doesn't take care of RsvdP/RsvdZ[*] bits in
controller SERR-INT register. This might cause unpredicable
results. This patch fixes this bug.
[*] RsvdP and RsvdZ are defined in SHPC spec as follows:
RsvdP - Reserved and Preserved. Register bits of this type are
reserved for future use as R/W bits. The value read is
undefined. Writes are ignored. Software must follow These rules
when accessing RsvdP bits:
- Software must ignore RsvdP bits when testing values read
from these registers.
- Software must not depend on RsvdP bit's ability to retain
information when written
- Software must always write back the value read in the RsvdP
bits when writing one of these registers.
RsvdZ - Reserved and Zero. Register bits of this type are reserved
for future use as R/WC bits. The value read is undefined. Writes
are ignored. Software must follow these rules when accessing RsvdZ
bits:
- Software must ignore RsvdZ bits when testing values read
from these registers.
- Software must not depends on a RsvdZ bit's ability to retain
information when written.
- Software must always write 0 to RsvdZ bits when writing one
of these register.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current SHPCHP driver doesn't take care of RsvdP/RsvdZ[*] bits
in logical slot registers. This might cause unpredicable results. This
patch fixes this bug.
[*] RsvdP and RsvdZ are defined in SHPC spec as follows:
RsvdP - Reserved and Preserved. Register bits of this type are
reserved for future use as R/W bits. The value read is
undefined. Writes are ignored. Software must follow These rules
when accessing RsvdP bits:
- Software must ignore RsvdP bits when testing values read
from these registers.
- Software must not depend on RsvdP bit's ability to retain
information when written
- Software must always write back the value read in the RsvdP
bits when writing one of these registers.
RsvdZ - Reserved and Zero. Register bits of this type are reserved
for future use as R/WC bits. The value read is undefined. Writes
are ignored. Software must follow these rules when accessing RsvdZ
bits:
- Software must ignore RsvdZ bits when testing values read
from these registers.
- Software must not depends on a RsvdZ bit's ability to retain
information when written.
- Software must always write 0 to RsvdZ bits when writing one
of these register.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up the code to access bits in slot logical
registers. This patch has no functional change.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up the code to access slot logical registers. This
patch has no functional changes.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch cleans up the code to access SHPC working register
sets. This patch has no functional changes.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current PCHEHP driver doesn't have any code to program hotplug
parameters from firmware. So hotplug parameters are never programed at
hot-add time. This patch add support for programming hotplug
parameters to PCIEHP driver.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for _HPX (Hot Plug Parameter Extensions)
defined in ACPI3.0a spec.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts the improper error message about OSHP evaluation
to debug message which is displayed only when pci_hotplug.ko is loaded
with debugging mode enabled. To do this, this patch adds a new module
parameter "debug_acpi" to pci_hotplug.ko for enabling/disabling debug
messages in acpi_pcihp.c.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the problem that hotplug parameters are not programed
when PCI cards are hot-added by ACPIPHP, SHPCHP and PCIEHP driver. The
pci_dev structure being hot-added is not bound to ACPI handle, so we
need to trace PCI bus tree to find ACPI handle.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't call pci_enable_device from pciehp because the pcie port service driver
already does this.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
acpi_os_free should not be used by drivers outside
of acpi/*/*.c. Replace with kfree().
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When acpiphp_enable_slot() is failed, acpiphp does not change
the slot->flags. Therefore, when user tries to read power
status, acpiphp_get_power_status() returns the enable status
whether the slot is not really enabled.
This patch fixes this BUG.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I encountered the problem that when there are some hotplug
slots are under the host bridge, the hotplug slots under the
p2p bridge are not treated as hotpluggable.
This patch fixes this BUG.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
o hotplug slots add
When the hot-added PCI device is p2p bridge, acpiphp calls
find_p2p_bridge() to add hotplug slots.
o hotplug slots remove
When the hot-removing PCI device is p2p bridge, acpiphp
calls cleanup_p2p_bridge() to remove hotplug slots.
o notify handler exchange
When the p2p bridge is added, acpiphp changes the notify
hanlder.
If no bridge device is inserted into the hotpluggable PCI
slot, acpiphp installs the notify handler for function.
After the p2p bridge hot-add, acpiphp has to install the
notify handler for bridge. Because, the role of the
handlers are not same. The hot-remove case is ditto.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current acpiphp does not free acpi_device structs when the
PCI devices are removed. When the PCI device is added,
acpi_bus_add() fails because acpi_device struct has already
exists. So, _PRT method does not evaluate.
This patch fixes this issue.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SGI hotplug driver changes required to support Tollhouse system PCI
hotplug, and implements the PRF_HOTPLUG_SUPPORT feature bit.
Signed-off-by: Prarit Bhargava <prarit@sgi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Andrew Victor
This patch includes a number of updates to the AT91RM9200 serial driver.
Changes include:
1. Conversion to a platform_driver. [Ivan Kokshaysky]
2. Replaced all references to AT91RM9200 with AT91. This driver can now
also be used for the AT91SAM9216.
3. Allow TIOCM_LOOP to configure local loopback mode.
4. Cleaned up the 'read_status_mask' usage and interrupt handler code.
[Chip Coldwell]
5. Suspend/resume support. [David Brownell]
There are a few 'unused variable' warning when compiling this - I
removed the new DMA support to keep this first patch simpler.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Badge4 PCMCIA driver was referencing structure elements which
had been renamed. Fix the missing renames.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
This patch adds the serial driver for Hilscher's netX network
processors.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Set the default triggers for the LOCOMO LED driver.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch includes code cleanups and minor fixes to the AT91RM9200 MMC
driver.
1. Replace calls to DBG() with pr_debug().
2. 'host' can never be null, so don't bother checking for that case.
3. Remove SA_SAMPLE_RANDOM from request_irq(). [Patch from Matt
Mackall]
4. clk_get() doesn't return NULL on error - need to test returned value
with IS_ERR().
5. Free resources if clk_get() or request_irq() fails.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MMC specification allows non-power of two block sizes. As such,
we should not pass the log2 block size to host drivers, but instead
pass the byte size.
However, ARM MMCI can only work with log2 block size, so continue to
pass both the log2 block size and byte block size. This means that
for the moment, the byte block size must remain a power of two, but
this is the first stage of removing this restriction for other hosts.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix unused variables and commenting since tglx's
new NAND updates
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Patch from Ben Dooks
Core support for the Samsung S3C2442, and the
serial port driver update to allow the serial
port blocks to be used.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
Reworking of the adaptation macros to allow driver to compile again
for the lpd7x's. Also, support added for the lh79520 so it may use
the smc91x.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
Board support and LCD panel configurations to integrate lh7a40x's with
the amba clcd driver.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Marc Singer
The serial driver now sets up the third UART when it is to be used.
Signed-off-by: Marc Singer <elf@buici.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since parport_serial uses symbols from 8250_pci, there should
be a dependency between the configuration symbols for these
two modules. Problem reported by Andrey Borzenkov
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current stack treats NETIF_F_HW_CSUM and NETIF_F_NO_CSUM
identically so we test for them in quite a few places. For the sake
of brevity, I'm adding the macro NETIF_F_GEN_CSUM for these two. We
also test the disjunct of NETIF_F_IP_CSUM and the other two in various
places, for that purpose I've added NETIF_F_ALL_CSUM.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu pointed out that it is unsafe to call netif_tx_disable()
from LLTX drivers because it uses dev->xmit_lock to synchronize
whereas LLTX drivers use private locks.
Convert tg3 to non-LLTX to fix this issue. tg3 is a lockless driver
where hard_start_xmit and tx completion handling can run concurrently
under normal conditions. A tx_lock is only needed to prevent
netif_stop_queue and netif_wake_queue race condtions when the queue
is full.
So whether we use LLTX or non-LLTX, it makes practically no
difference.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove tx_lock where it is unnecessary. tg3 runs lockless and so it
requires interrupts to be disabled and sync'ed, netif_queue and NAPI
poll to be stopped before the device can be reconfigured. After
stopping everything, it is no longer necessary to get the tx_lock.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use CPU native page size to determine various ring sizes. This allows
order-0 memory allocations on all systems.
Added check to limit the page size to 16K since that's the maximum rx
ring size that will be used. This will prevent using unnecessarily
large page sizes on some architectures with large page sizes.
[Suggested by David Miller]
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change bnx2_fw.h to use compressed text for all CPU images.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions to decompress firmware before loading to the internal
CPUs. Compressing the firmware reduces the driver size significantly.
Added file name length sanity check in the gzip header to prevent
going past the end of buffer [suggested by DaveM].
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow WOL settings on 5708 B2 and newer chips that have the problem
fixed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cleans the STIR421x part of the irda-usb code. We also no longer
try to load all existing firmwares but only the matching one
(according to the USB id we get from the dongle).
Signed-off-by: Nick Fedchik <nfedchik@atlantic-link.com.ua>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ppp_receive_nonmp_frame, we call pskb_may_pull(skb, skb->len) if the
tailroom is >= 124. This is pointless because this pskb_may_pull is only
needed if the skb is non-linear. However, if it is non-linear then the
tailroom would be zero.
So it can be safely removed.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The linearisation operation doesn't need to be super-optimised. So we can
replace __skb_linearize with __pskb_pull_tail which does the same thing but
is more general.
Also, most users of skb_linearize end up testing whether the skb is linear
or not so it helps to make skb_linearize do just that.
Some callers of skb_linearize also use it to copy cloned data, so it's
useful to have a new function skb_linearize_cow to copy the data if it's
either non-linear or cloned.
Last but not least, I've removed the gfp argument since nobody uses it
anymore. If it's ever needed we can easily add it back.
Misc bugs fixed by this patch:
* via-velocity error handling (also, no SG => no frags)
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Various drivers use xmit_lock internally to synchronise with their
transmission routines. They do so without setting xmit_lock_owner.
This is fine as long as netpoll is not in use.
With netpoll it is possible for deadlocks to occur if xmit_lock_owner
isn't set. This is because if a printk occurs while xmit_lock is held
and xmit_lock_owner is not set can cause netpoll to attempt to take
xmit_lock recursively.
While it is possible to resolve this by getting netpoll to use
trylock, it is suboptimal because netpoll's sole objective is to
maximise the chance of getting the printk out on the wire. So
delaying or dropping the message is to be avoided as much as possible.
So the only alternative is to always set xmit_lock_owner. The
following patch does this by introducing the netif_tx_lock family of
functions that take care of setting/unsetting xmit_lock_owner.
I renamed xmit_lock to _xmit_lock to indicate that it should not be
used directly. I didn't provide irq versions of the netif_tx_lock
functions since xmit_lock is meant to be a BH-disabling lock.
This is pretty much a straight text substitution except for a small
bug fix in winbond. It currently uses
netif_stop_queue/spin_unlock_wait to stop transmission. This is
unsafe as an IRQ can potentially wake up the queue. So it is safer to
use netif_tx_disable.
The hamradio bits used spin_lock_irq but it is unnecessary as
xmit_lock must never be taken in an IRQ handler.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
cn_queue.c:130: warning: value computed is not used
There is no point in testing the atomic value if the result is thrown
away.
From Evgeniy:
It was created to put implicit smp barrier, but it is not needed there.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add recovery logic when we suspect that the system is re-ordering
MMIOs. Re-ordered MMIOs to the send mailbox can cause bogus tx
completions and hit BUG_ON() in the tx completion path.
tg3 already has logic to handle re-ordered MMIOs by flushing the MMIOs
that must be strictly ordered (such as the send mailbox). Determining
when to enable the flush is currently a manual process of adding known
chipsets to a list.
The new code replaces the BUG_ON() in the tx completion path with the
call to tg3_tx_recover(). It will set the TG3_FLAG_MBOX_WRITE_REORDER
flag and reset the chip later in the workqueue to recover and start
flushing MMIOs to the mailbox.
A message to report the problem will be printed. We will then decide
whether or not to add the host bridge to the list of chipsets that do
re-ordering.
We may add some additional code later to print the host bridge's ID so
that the user can report it more easily.
The assumption that re-ordering can only happen on x86 systems is also
removed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PCI ID for BCM5786 which is a variant of 5787.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch gets rid of the old power management code and now uses the
device model for the ali-ircc driver.
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
stir4200 uses a kernel thread for its TX/RX operations, and it is now
converted to the kernel kthread API.
Tested on an STIR4200 based dongle.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MosChip MCS7780 chipset is an IrDA USB bridge that
doesn't conform with the IrDA-USB standard and thus needs
its separate driver.
Tested on an actual MCS7780 based dongle.
Original implementation by Brian Pugh <bpugh@cs.pdx.edu>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
for_each_cpu() is going away (and is gone in -mm).
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provides for pinning user space pages in memory, copying to iovecs,
and copying from sk_buffs including fragmented and chained sk_buffs.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attempts to allocate per-CPU DMA channels
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pete Zaitcev