Something I failed to notice while testing the mceusb RLE buffer
decoding simplification patches was that we were getting an extra event
from the previously pressed key.
As was pointed out to me on irc by Maxim, this is actually due to using
ir_raw_event_store_with_filter without having set up a timeout value.
The hardware has a timeout value we're now reading and storing, which
properly enables the transition to idle in the raw event storage
process, and makes IR decode behave correctly w/o keybounce.
Also remove no-longer-used ir_raw_event struct from mceusb_dev struct
and add as-yet-unused enable flags for carrier reports and learning
mode, which I'll hopefully start wiring up sooner than later. While
looking into that, found evidence that 0x9f 0x15 responses are only
non-zero when the short-range learning sensor is used, so correct the
debug spew message, and then suppress it when using the standard
long-range sensor.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If we pass in an offset, we shouldn't skip 2 bytes. And the first-gen
hardware generates a constant stream of interrupts, always with two
header bytes, and if there's been no IR, with nothing else. Bail from
ir processing without calling ir_handle_raw_event when we get such a
buffer delivered to us.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We were storing a bunch of spaces at the end of each signal, rather than
a single long space. The in-kernel decoders were actually okay with
this, but lirc isn't. As suggested by David Härdeman, switch to storing
samples using ir_raw_event_store_with_filter, which auto-merges the
consecutive space samples for us. This also allows us to bypass having
to store rawir samples in our device struct, further simplifying the
buffer parsing state machine. Both in-kernel decoders and lirc are happy
again with this change.
Also included in this patch is proper parsing of 0x9f 0x01 commands, the
removal of some magic number usage and some printk spew fixups.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rather than waiting for trigger bits, the formula for which was slightly
messy, and apparently, not actually 100% complete for some remotes, just
call ir_raw_event_handle whenever we finish parsing a chunk of data from
the rx fifo, similar to mceusb, as well as whenever we see an 'end of
signal data' 0x80 packet.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Another multi-function Conexant device. Interface 0 is IR, though on
this model, TX isn't wired up at all, so I've mixed in support for
models without TX (and verified that lircd says TX isn't supported when
trying to send w/this device).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
FIMC IP in S5Pv310 series has extended DMA status registers
and some bit fields are marked as reserved comparing to S5PC100/110.
Use correct registers for getting DMA write pointer in each SoC variant
supported by the driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace V4L2_PIX_FMT_RGB24 code with V4L2_PIX_FMT_RGB32
since the hardware uses 24-bits for actual pixel data but pixels
are 4-byte aligned in memory.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create separate vidioc_g_crop/vidioc_s_crop handlers for capture
video node and so image cropping parameters are properly queried
at FIMC input (image sensor) and not at FIMC output.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The test for driver->owner != NULL in sh_mobile_ceu_camera.c is unneeded and it
breaks the static build of sh_mobile_csi2.c. Remove it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When SOCAM_PCLK_SAMPLE_FALLING, just leave CSICR1_REDGE unset, otherwise we get
the inverted behaviour.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
BugLink: http://launchpad.net/bugs/580006
SKU turns off auto-mute for these machines, so ignore the SKU.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch modifies IPsec6 to fragment IPv6 packets that are
locally generated as needed.
This version of the patch only fragments in tunnel mode, so that fragment
headers will not be obscured by ESP in transport mode.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus reported that the new warning introduced by commit f26f9aff6a
"Sched: fix skip_clock_update optimization" triggers. The need_resched
flag can be set by other CPUs asynchronously so this debug check is
bogus - remove it.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
LKML-Reference: <AANLkTinJ8hAG1TpyC+CSYPR47p48+1=E7fiC45hMXT_1@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32: Make sure we can map all of lowmem if we need to
x86, vt-d: Handle previous faults after enabling fault handling
x86: Enable the intr-remap fault handling after local APIC setup
x86, vt-d: Fix the vt-d fault handling irq migration in the x2apic mode
x86, vt-d: Quirk for masking vtd spec errors to platform error handling logic
x86, xsave: Use alloc_bootmem_align() instead of alloc_bootmem()
bootmem: Add alloc_bootmem_align()
x86, gcc-4.6: Use gcc -m options when building vdso
x86: HPET: Chose a paranoid safe value for the ETIME check
x86: io_apic: Avoid unused variable warning when CONFIG_GENERIC_PENDING_IRQ=n
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Fix off by one in perf_swevent_init()
perf: Fix duplicate events with multiple-pmu vs software events
ftrace: Have recordmcount honor endianness in fn_ELF_R_INFO
scripts/tags.sh: Add magic for trace-events
tracing: Fix panic when lseek() called on "trace" opened for writing
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix the irqtime code for 32bit
sched: Fix the irqtime code to deal with u64 wraps
nohz: Fix get_next_timer_interrupt() vs cpu hotplug
Sched: fix skip_clock_update optimization
sched: Cure more NO_HZ load average woes
Since commit 3e4d3af501 "mm: stack based kmap_atomic()", it is actively
wrong to rely on fixed kmap type indices (namely KM_L2_CACHE) as
kmap_atomic() totally ignores them and a concurrent instance of it may
happily reuse any slot for any purpose. Because kmap_atomic() is now
able to deal with reentrancy, we can get rid of the ad hoc mapping here.
While the code is made much simpler, there is a needless cache flush
introduced by the usage of __kunmap_atomic(). It is not clear if the
performance difference to remove that is worth the cost in code
maintenance (I don't think there are that many highmem users on that
platform anyway) but that should be reconsidered when/if someone cares
enough to do some measurements.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Since commit 3e4d3af501 "mm: stack based kmap_atomic()", it is actively
wrong to rely on fixed kmap type indices (namely KM_L2_CACHE) as
kmap_atomic() totally ignores them and a concurrent instance of it may
happily reuse any slot for any purpose. Because kmap_atomic() is now
able to deal with reentrancy, we can get rid of the ad hoc mapping here,
and we even don't have to disable IRQs anymore (highmem case).
While the code is made much simpler, there is a needless cache flush
introduced by the usage of __kunmap_atomic(). It is not clear if the
performance difference to remove that is worth the cost in code
maintenance (I don't think there are that many highmem users on that
platform if at all anyway).
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Since commit 3e4d3af501 "mm: stack based kmap_atomic()", it is no longer
necessary to carry an ad hoc version of kmap_atomic() added in commit
7e5a69e83b "ARM: 6007/1: fix highmem with VIPT cache and DMA" to cope
with reentrancy.
In fact, it is now actively wrong to rely on fixed kmap type indices
(namely KM_L1_CACHE) as kmap_atomic() totally ignores them now and a
concurrent instance of it may reuse any slot for any purpose.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: handle rt_sigreturn() more cleanly
arch/tile: handle CLONE_SETTLS in copy_thread(), not user space
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86: avoid high BIOS area when allocating address space
x86: avoid E820 regions when allocating address space
x86: avoid low BIOS area when allocating address space
resources: add arch hook for preventing allocation in reserved areas
Revert "resources: support allocating space within a region from the top down"
Revert "PCI: allocate bus resources from the top down"
Revert "x86/PCI: allocate space from the end of a region, not the beginning"
Revert "x86: allocate space within a region top-down"
Revert "PCI: fix pci_bus_alloc_resource() hang, prefer positive decode"
PCI: Update MCP55 quirk to not affect non HyperTransport variants
We should not be incrementing mm_users when we startup a secondary
CPU - doing so results in mm_users incrementing by one each time we
hotplug a CPU, which will eventually wrap, and will cause problems.
Other architectures such as x86 do not increment mm_users, but only
mm_count, so we follow that pattern.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Keep the crash kernel address below 512 MiB for 32 bits and 896 MiB
for 64 bits. For 32 bits, this retains compatibility with earlier
kernel releases, and makes it work even if the vmalloc= setting is
adjusted.
For 64 bits, we should be able to increase this substantially once a
hard-coded limit in kexec-tools is fixed.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20101217195035.GE14502@redhat.com>
The current tile rt_sigreturn() syscall pattern uses the common idiom
of loading up pt_regs with all the saved registers from the time of
the signal, then anticipating the fact that we will clobber the ABI
"return value" register (r0) as we return from the syscall by setting
the rt_sigreturn return value to whatever random value was in the pt_regs
for r0.
However, this breaks in our 64-bit kernel when running "compat" tasks,
since we always sign-extend the "return value" register to properly
handle returned pointers that are in the upper 2GB of the 32-bit compat
address space. Doing this to the sigreturn path then causes occasional
random corruption of the 64-bit r0 register.
Instead, we stop doing the crazy "load the return-value register"
hack in sigreturn. We already have some sigreturn-specific assembly
code that we use to pass the pt_regs pointer to C code. We extend that
code to also set the link register to point to a spot a few instructions
after the usual syscall return address so we don't clobber the saved r0.
Now it no longer matters what the rt_sigreturn syscall returns, and the
pt_regs structure can be cleanly and completely reloaded.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Previously we were just setting up the "tp" register in the
new task as started by clone() in libc. However, this is not
quite right, since in principle a signal might be delivered to
the new task before it had its TLS set up. (Of course, this race
window still exists for resetting the libc getpid() cached value
in the new task, in principle. But in any case, we are now doing
this exactly the way all other architectures do it.)
This change is important for 2.6.37 since the tile glibc we will
be submitting upstream will not set TLS in user space any more,
so it will only work on a kernel that has this fix. It should
also be taken for 2.6.36.x in the stable tree if possible.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: stable <stable@kernel.org>
If a device is reported as inactive or not present by its _STA
control method, acpi_bus_check_add() skips it without evaluating its
_PRW method. This leads to a problem when the device's _PRW method
points to a GPE, because in that case the GPE may be enabled by
ACPICA during the subsequent acpi_update_gpes() call which, in
turn, may cause a GPE storm to appear.
To avoid this issue, make acpi_bus_check_add() evaluate _PRW for
inactive or not present devices and register the wakeup GPE
information returned by them, so that acpi_update_gpes() does not
enable their GPEs unnecessarily.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The initial values of the registers 0x01 and 0x17 are taken from the sensor
table at capture start and updated according to the flag PDN_INV.
Their values are updated at each step of the capture initialization and
memorized for reuse in capture stop.
This patch also fixed automatically some bad hardcoded values of these
registers.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The flag PDN_INV indicates that the sensor pin S_PWR_DN has not the same
value as other webcams with the same sensor. For now, only two webcams have
been so detected: the Microsoft's VX1000 and VX3000.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After Mauro's "bttv: Fix locking issues due to BKL removal code" there
are a number of comments that are no longer needed about lock ordering.
Remove them.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a regression where bttv driver causes oopses when loading, since it
were using some non-initialized mutexes. While it would be possible to
fix the issue, there are some other lock troubles, like to the presence of
lock code at free_btres_lock().
It is possible to fix, but the better is to just use the core-assisted
locking schema. This way, V4L2 core will serialize access to all
ioctl's/open/close/mmap/read/poll operations, avoiding to have two
processes accessing the hardware at the same time. Also, as there's just
one lock, instead of 3, there's no risk of dead locks.
The net result is a cleaner code, with just one lock.
Reported-by: Dan Carpenter <error27@gmail.com>
Reported-by: Brandon Philips<brandon@ifup.org>
Reported-by: Chris Clayton <chris2553@googlemail.com>
Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
$ cat << EOF | gcc -Wconversion -xc -S -o/dev/null -
unsigned f(void) {return NLMSG_HDRLEN;}
EOF
<stdin>: In function 'f':
<stdin>:3:26: warning: negative integer implicitly converted to unsigned type
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Logitec LAN-GTJ U2A (http://www.pro.logitec.co.jp/pro/g/gLAN-GTJU2A/)
USB 2.0 10/10/1000 Ethernet adapter is based on ASIX AX88178 chipset.
This patch adds missing USB ID for the device.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seen with malta_defconfig on Linus' tree:
CC arch/mips/mm/sc-mips.o
arch/mips/mm/sc-mips.c: In function 'mips_sc_is_activated':
arch/mips/mm/sc-mips.c:77: error: 'config2' undeclared (first use in this function)
arch/mips/mm/sc-mips.c:77: error: (Each undeclared identifier is reported only once
arch/mips/mm/sc-mips.c:77: error: for each function it appears in.)
arch/mips/mm/sc-mips.c:81: error: 'tmp' undeclared (first use in this function)
make[2]: *** [arch/mips/mm/sc-mips.o] Error 1
make[1]: *** [arch/mips/mm] Error 2
make: *** [arch/mips] Error 2
[Ralf: Cosmetic changes to minimize the number of arguments passed to
mips_sc_is_activated]
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/1752/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
My conversion of tehuti to use request_firmware() was confused about
the filename of the firmware blob. Change the driver to match the
blob.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This prevents allocation of the last 2MB before 4GB.
The experiment described here shows Windows 7 ignoring the last 1MB:
https://bugzilla.kernel.org/show_bug.cgi?id=23542#c27
This patch ignores the top 2MB instead of just 1MB because H. Peter Anvin
says "There will be ROM at the top of the 32-bit address space; it's a fact
of the architecture, and on at least older systems it was common to have a
shadow 1 MiB below."
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When we allocate address space, e.g., to assign it to a PCI device, don't
allocate anything mentioned in the BIOS E820 memory map.
On recent machines (2008 and newer), we assign PCI resources from the
windows described by the ACPI PCI host bridge _CRS. On many Dell
machines, these windows overlap some E820 reserved areas, e.g.,
BIOS-e820: 00000000bfe4dc00 - 00000000c0000000 (reserved)
pci_root PNP0A03:00: host bridge window [mem 0xbff00000-0xdfffffff]
If we put devices at 0xbff00000, they don't work, probably because
that's really RAM, not I/O memory. This patch prevents that by removing
the 0xbfe4dc00-0xbfffffff area from the "available" resource.
I'm not very happy with this solution because Windows solves the problem
differently (it seems to ignore E820 reserved areas and it allocates
top-down instead of bottom-up; details at comment 45 of the bugzilla
below). That means we're vulnerable to BIOS defects that Windows would not
trip over. For example, if BIOS described a device in ACPI but didn't
mention it in E820, Windows would work fine but Linux would fail.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=16228
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This implements arch_remove_reservations() so allocate_resource() can
avoid any arch-specific reserved areas. This currently just avoids the
BIOS area (the first 1MB), but could be used for E820 reserved areas if
that turns out to be necessary.
We previously avoided this area in pcibios_align_resource(). This patch
moves the test from that PCI-specific path to a generic path, so *all*
resource allocations will avoid this area.
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This adds arch_remove_reservations(), which an arch can implement if it
needs to protect part of the address space from allocation.
Sometimes that can be done by just putting a region in the resource tree,
but there are cases where that doesn't work well. For example, x86 BIOS
E820 reservations are not related to devices, so they may overlap part of,
all of, or more than a device resource, so they may not end up at the
correct spot in the resource tree.
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This reverts commit b126b4703a.
We're going back to the old behavior of allocating from bus resources
in _CRS order.
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
