The driver version numbers and changelog have not been updated in a
long while to reflect actual changes. Remove the version number and
add a notice that later changes can be tracked in SCM.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 4994cd8dad introduced a
regression which causes xpad to report force feedback cababilities
for non-360 controllers too, even while there is no actual support
for those.
Fix that by adding a check for XTYPE_XBOX360 to xpad_init_ff().
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The buttons BTN_C and BTN_Z are only used in the original xbox
controller, not in xbox360 controller. Therefore only add them to
keybit when the controller is a non-360 one.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add Mad Catz and 0x0e6f xbox360 controllers which are already found
in xpad_device[] table in xpad.c into the vendor id list. Also add
Logitech into the vendor list for Logitech Chillstream gamepads.
Also add the RedOctane Guitar Hero X-plorer.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The commit ae91d10aab inverted Y and RY
axes on xbox360 so that up is positive and down is negative.
This is wrong, as axes on game controllers have up as negative per
convention. Also, even xpad itself reports HAT0X with up as negative.
Fix that by inverting them again.
Also, according to http://bugzilla.kernel.org/show_bug.cgi?id=10337 the
original xbox controllers also have the Y and RY axes inverted.
Fix that by inverting them as well.
Cc: Brian Magnuson <bdmagnuson@gmail.com>
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
For devices not specifically listed in xpad.c, xpad->dpad_mapping
is initially set to MAP_DPAD_UNKNOWN. In xpad_probe() it gets changed
to either MAP_DPAD_TO_BUTTONS or MAP_DPAD_TO_AXES, depending on the
module parameter dpad_to_buttons.
However, MAP_DPAD_UNKNOWN is defined as -1, while the field is u8.
This results in actual value of 255, causing the MAP_DPAD_UNKNOWN
check in xpad_probe() to fail.
Fix that by defining MAP_DPAD_UNKNOWN as 2 instead.
Also, setting module parameter dpad_to_buttons to 1 should obviously
map dpad to buttons, while the default behaviour (0) should be to map
dpad to axes. However, dpad_to_buttons is directly assigned to
xpad->dpad_mapping, and as MAP_DPAD_TO_BUTTONS is 0, the actual
behaviour is reversed.
Fix that by negating dpad_to_buttons in assignment.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Match Xbox 360 controllers using the interface info, i.e. interface
class 255 (Vendor specific), subclass 93 and protocol 1, instead of
specifying the device ids individually. As the class is vendor-specific,
we have to still match against vendor id as well, though.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Graeme Gregory <gg@opensource.wolfsonmicro.com>
Signed-off-by: Mike Arthur <mike.arthur@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Graeme Gregory <gg@opensource.wolfsonmicro.com>
Signed-off-by: Mike Arthur <mike.arthur@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Lars Munch <lars@segv.dk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Graeme Gregory <gg@opensource.wolfsonmicro.com>
Signed-off-by: Mike Arthur <mike.arthur@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Lars Munch <lars@segv.dk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Graeme Gregory <gg@opensource.wolfsonmicro.com>
Signed-off-by: Mike Arthur <mike.arthur@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add support for the touchscreen controllers provided by Wolfson
Microelectronics WM97xx series chips in both polled and streaming
modes.
These drivers have been maintained out of tree since 2003. During
that time the driver the primary maintainer was Liam Girdwood and
a number of people have made contributions including Dmitry Baryshkov,
Stanley Cai, Rodolfo Giometti, Russell King, Marc Kleine-Budde,
Ian Molton, Vincent Sanders, Andrew Zabolotny, Graeme Gregory,
Mike Arthur and myself. Apologies to anyone I have omitted.
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Graeme Gregory <gg@opensource.wolfsonmicro.com>
Signed-off-by: Mike Arthur <mike.arthur@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This updates the ads7846 driver to handle external vREF (required
on boards using ads7843 chips) without module parameters, and also
removes a needless variable with its associated bogus gcc warning.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Enables the Sharp Zaurus Collie and Poodle devices to be turned off
by pressing the "Cancel" button for a few seconds (as designed by
Sharp).
Additional small cleanups:
- removal of unused #defines and variables
- add missing __devinit/__devexit/__devinitconst annotations
- reorganized copyright notice
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Everyone should be using input_{get|set}_drvdata() by now.
Alias them to dev_{get|set}_drvdata() and remove ->private.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Recent driver core change causes references to parent devices being
dropped early, at device_del() time, as opposed to when all children
are freed. This causes oops in evdev with grabbed devices. Take the
reference to the parent input device ourselves to ensure that it
stays around long enough.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When getting disconnected we need to release eventual grabs on the
underlying input device as we also release the input device itself.
Otherwise, we would try to release the grab when the client that
requested it closes its handle, accessing the input device which
might already be freed.
Signed-off-by: Björn Steinbrink <B.Steinbrink@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following patch allows ixp4xx-beeper to be loaded by udev
automatically when compiled as a module with kernel versions 2.4.24 and
greater.
This patch is required because 43cc71eed1
("platform: prefix MODALIAS with "platform:"") changed the modalias
string to have the extra prefix.
LKG7102D7:~# udevinfo -a -p /sys/devices/platform/ixp4xx-beeper.4
looking at device '/devices/platform/ixp4xx-beeper.4':
KERNEL=="ixp4xx-beeper.4"
SUBSYSTEM=="platform"
DRIVER==""
ATTR{modalias}=="platform:ixp4xx-beeper"
udev therefore tries to modprobe platform:ixp4xx-beeper instead of
ixp4xx-beeper.
LKG7102D7:~# udevtest /sys/devices/platform/ixp4xx-beeper.4
...
import_uevent_var: import into environment: 'PHYSDEVBUS=platform'
import_uevent_var: import into environment: 'MODALIAS=platform:ixp4xx-beeper'
main: looking at device '/devices/platform/ixp4xx-beeper.4' from
subsystem 'platform'
wait_for_sysfs: file '/sys/devices/platform/ixp4xx-beeper.4/bus'
appeared after 0 loops
main: run: 'socket:/org/kernel/udev/monitor'
main: run: '/sbin/modprobe --use-blacklist platform:ixp4xx-beeper'
With this patch, depmod adds an alias line (see below) to
modules.alias which allows modprobe to load the right module.
alias platform:ixp4xx-beeper ixp4xx-beeper
Signed-off-by: Gordon Farquharson <gordonfarquharson@gmail.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a crash in the apm-power driver when an input-device, such as
keyboard driver module, is unloaded.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We want to mask (key_number - 1), not key_number. The current
implementation works fine for all values but the maximum one,
i.e. 8.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Secondary input device did not have parent set up causing it
to appear in the root of sysfs device hierarchy.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add support for new wacom tablets - Bamboo1, BambooFun, and Cintiq 12WX
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
drivers/input/touchscreen/ads7846.c: In function 'ads7846_read12_ser':
drivers/input/touchscreen/ads7846.c:216: warning: 'sample' may be used uninitialized in this function
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
SNI RM200 don't have the i8042 controller connected to the EISA bus,
but have a second address range for onboard devices. This patch handles
the two possible address ranges for the i8042 on SNI RMs.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit c18bab80 ("Input: i8042 - non-x86 build fix") introduced the
following warning on non-x86 builds:
drivers/input/serio/i8042.c: In function 'i8042_probe':
drivers/input/serio/i8042.c:1154: warning: unused variable 'param'
Fix this by moving the parameter variable declaration into the #ifdef too.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
- fix compile errors (keymap is in bdev, not pdev)
- cdev is no more (must use dev.parent)
- update copiright notice
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add to help text that the Intel I2C ICH (i801) driver is also needed
for this kernel.
Add LEDS_CLASS to config since the driver makes les_classdev_*() calls:
ERROR: "led_classdev_register" [drivers/input/misc/apanel.ko] undefined!
ERROR: "__led_classdev_unregister" [drivers/input/misc/apanel.ko]
undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add architecture support for the MN10300/AM33 CPUs produced by MEI to the
kernel.
This patch also adds board support for the ASB2303 with the ASB2308 daughter
board, and the ASB2305. The only processor supported is the MN103E010, which
is an AM33v2 core plus on-chip devices.
[akpm@linux-foundation.org: nuke cvs control strings]
Signed-off-by: Masakazu Urade <urade.masakazu@jp.panasonic.com>
Signed-off-by: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As discussed on LKML some notion of 'function' is needed in
LED naming. This patch adds this to the documentation and
standardises existing LED drivers.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
This header file exists only for some hacks to adapt alsa-driver
tree. It's useless for building in the kernel. Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it. This should be really killed in
future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Currently, only one debounce_interval is introduced for both direct and
matrix keys. This is true in most cases, although the keypad controller
supports different debounce for direct/matrix keys.
Some platforms do require this to be tuned, instead of the default
reset value of 100ms.
Rotary encoder will always use zero debounce time for now to achieve
certain sensitivity.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
1. use ioremap() for registers access, this improves the portability
of the driver (e.g. same IP on different processor with different
I/O memory range), and make it possible to remove those registers
definition in pxa-regs.h as PXA is undergoing a clean-up of that
header file
2. use device specific IRQ instead of hardcoded IRQ_KEYPAD, same
reason as above
3. clean up the error handling path in _probe()
4. remove DRIVER_NAME and use pdev->name when necessary, we don't
actually need a constant string literals
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
1. Rotary encoder events can be configured either as relative events
as the legacy code does or as any specified key code, this is
useful on some platform which uses the rotary keys as
KEY_{UP/DOWN/LEFT/RIGHT}
2. Add support for direct keys, the corresponding keycodes for each
direct key can now be specified within the platform data
3. Remove the direct/rotary key detection code from the IRQ handler
to dedicated functions to improve readability
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Introduce pxa27x_keypad_config() for keypad registers configuration
and remove the reg_kpc, reg_kprec from platform data structure
so that configurations of keypad registers can be centralized to a
single function.
It can also be re-used when resuming.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
1. Introduce the "struct pxa27x_keypad" structure for driver specific
information, such as "struct clk", generated matrix key codes and
so on
2. Use KEY() macro to define matrix keys, instead of original 8x8 map
this makes definition easier with keypad where keys are sparse
3. Keep a generated array in "struct pxa27x_keypad" for fast lookup
4. Separate the matrix scan into a dedicated function for readability
and report only those keys whose state has been changed, instead
of report all states
5. Make use of KPAS to decide the faster path if only one key has been
detected
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The pin configurations will slowly be moved to the board specific code
at initialization thus to make the driver more generic.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The controller should really be called keypad, and also align
the naming of functions and structures to use "pxa27x_keypad"
as prefix, instead of "pxakbd".
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If firmware does not implement AUX_LOOP comand in 32 bit mode it
is unlikely to implement it in 64 bit mode. Same goes for active
multiplexing. See:
http://bugzilla.kernel.org/show_bug.cgi?id=9664
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Acer Aspire 9110 series also requires the Dritek quirk to enable the
extra scancodes.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds a very simple input power event to APM user suspend
event bridge. Its currently only works for the systems using the
emulated APM driver but could easily be extended to work with anything
with a true APM BIOS too.
This covers a standard embedded system need which is to suspend when the
user presses a suspend button. It leaves options open to system
integrators to ignore (or unload) this code and implement their own more
complex event handling system.
Its hidden behind the EMBEDDED Kconfig option since its only likely to
be of use to embedded style systems. It can be built as a module so the
"hardcoded" policy can easily be removed from the kernel at runtime if
desired too.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
replace outb_p() with udelay(2). This is a real ISA device so it likely
needs this particular delay.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch refactors the code in corgi_lcd.c moving it to the board
specific corgi and spitz files where appropriate instead of the
existing ifdef mess which hinders readability.
Fix spitz_get_hsync_len() to call get_hsync_invperiod so pxafb can be
compiled as a module.
The confusing variables which represent the inverse horizintal sync
period are renamed to "invperiod" consistently.
An incorrect comment in corgi_ts.c is also corrected.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With a sparc64 defconfig modified to set CONFIG_HOTPLUG=n
the following error happened during link of vmlinux:
local symbol 0: discarded in section `.devexit.text' from drivers/built-in.o
local symbol 1: discarded in section `.devexit.text' from drivers/built-in.o
(The error message above is from kbuild.git but it happens in mainline too)
The error happens becase there is a reference from .text/.data to a
function marked __devexit. With CONFIG_HOTPLUG=n all code marked
__devexit are discarded and the linker complains.
It was tracked down to sparcspkr.c which were missing __devexit_p()
around the function pointers.
Unfortunately modpost did not catch this since modpost do not warn
about references from .data to .devexit from variables named *_driver.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cdev field was obsolete and provided only for backward compatibility
since conversion of input core from class devices to regular devices.
It is time to remove it.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some Wistron based laptops need us to explicitly enable the 'Dritek
keyboard extension' to make their extra keys start generating scancodes.
Originally, this was just confined to older laptops, but a few Acer
laptops have turned up in 2007 that also need this again.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add keyboard support on tosa (Sharp Zaurus SL-6000x).
Largely based on patches by Dirk Opfer.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This driver supports the application buttons on some Fujitsu Lifebook
laptops. It is based on the earlier apanel driver done by Jochen Eisenger,
but with many changes. The original driver used ioctl's and a separate
user space program (see http://apanel.sourceforge.net). This driver hooks
into the input subsystem so that the normal keys act as expected without a
daemon. In addition to buttons, the Mail Led is handled via LEDs class
device.
The driver now supports redefinable keymaps and no longer has to have a DMI
table for all Fujitsu laptops.
I thought about mixing this driver should be integrated into the Fujitsu
laptop extras driver that handles backlight, but rejected the idea because
it wasn't clear if all the Fujitsu laptops supported both.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This stops the ads7846 driver from using dev->power.power_state; that field is
deprecated (overdue for removal) and the only reason to update it was to make
the /sys/devices/.../power/state files (now removed) work better.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Drop #include <linux/moduleparam.h> in files that also include
linux/module.h, since module.h includes moduleparam.h already.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Rounding doesn't matter for the first tick, but we want
succeeding ticks to be aligned on second boundary if poll
interval is large enough.
Also: cancel_rearming_delayed_workqueue is marked as obsolete
in workqueue.h so use cancel_delayed_work_sync.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
RT guys advised me that in their kernels synchronize_sched() will not
work to ensure that all IRQ handlers run to their completion and that
synchronize_irq() should be used instead.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Take dev->event_lock to make sure that we don't race with input_event() and
also force key up event when removing a key from keymap table.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Most of Fn+F? special keys on (at least) the Dell Latitude laptops don't
generate a hardware key release event so the driver has to generate one.
Signed-off-by: Giel de Nijs <giel@caffeinetrip.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The recently added support for Dell Volstro 1400 was causing protocol
synchronization errors on Acer Aspire 5720ZG, fix it.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The lifebook driver may register a second input device, but it never
unregisters it. This fixes that.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If we successfully call input_register_device() in psmouse_connect()
but sysfs_create_group() fails, we'll enter the error path without
ever having called input_unregister_device() potentially leaking
memory.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix a buffer overflow in mutli-packet handling code. The overflow can
only happen with eGalax devices and is even there very unlikely (only
non-report packet are affected any only when truncated after the first
byte).
Also changes the mutli-packet handling code not to drop unknown packets,
but rather just drop one byte. This allows synchronizing on report packets
in the data stream. It's required for some egalax devices to work at all.
Also remove the pointless 'flags' member of the device struct and set the
version number to 0.6, plus some minor cleanups.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Devices like the HP Integrated Remote Console Virtual Mouse, which are
standard equipment on all Proliant and Integrity servers, produce
absolute coordinates instead of relative coordinates. This is done to
synchronize the position of the mouse cursor on the client desktop
with the mouse cursor position on the server. Mousedev is not
designed to pass those absolute events directly to X, but it can
translate them into relative movements. It currently does this for
tablet like devices and touchpads. This patch merely tells it to also
include a device with ABS_X, ABS_Y, and mouse buttons in its list of
devices to process input for.
This patch enables the mouse pointer to move when using the remote
console.
Signed-off-by: Micah Parrish <micah.parrish@hp.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: improve Kconfig help entries for HP Jornada devices
Input: pass EV_PWR events to event handlers
Input: spitzkbd - fix suspend key handling
gameport: don't export functions that are static inline
Input: jornada680_kbd - fix default keymap
Input: Handle EV_PWR type of input caps in input_set_capability.
input_handle_event() used to pass EV_PWR events to event handlers
but no longer does so in 2.6.23. Modules to trigger power management
events based on input power events exist but rely on the EV_PWR events
being passed to the input event handlers.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The spitz keyboard driver reports KEY_SUSPEND events but doesn't
register its use of this event in the keybit bitfield, breaking
input events for this key. This patch fixes that by registering
the key in the keybit bitfield.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This does not make sense and moreover causes build failures
on alpha.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch fixes the HP Jornada 6xx keyboard default keymap which had some
bad keymap values. This resulted in wrong key being returned when pressed
(for example, key 'y' returned 'r').
Also, while we are at it lets arrange the include files in alphabetical order.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Given the patch which simplifies the spi_sync calling convention, this one
updates the callers of that routine which tried using it according to the
previous specification. (Most didn't.)
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: adds the context menu key (HUT GenDesc 0x84)
Input: add definitions for frame forward and frame back keys
Input: bf54x-keys - keypad does not exist on BF544 parts
Input: gpio-keys - request and configure GPIOs
Input: i8042 - add i8042.noloop quirk for MS Virtual Machine
Sonypi: use synchronize_irq instead of sycnronize_sched
sonypi: fit input devices into sysfs tree
sony-laptop: fit input devices into sysfs tree
Currently, gpio_keys.c assumes the GPIOs to be already properly configured;
this patch changes gpio-keys to perform explicit calls to gpio_request() and
gpio_configure_input().
This matches the behaviour of leds-gpio.
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When booting under Microsoft Virtual Machine, the noloop quirk is
needed, otherwise PS/2 mouse is not properly detected.
Reported-by: Lawrence Steeger <vendor@russte.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Jazz machines have to use the PIT timer for dyntick and highresolution
kernels. This may break because currently just like i386 used to do MIPS
uses two separate spinlocks in the actual PIT code and the PC speaker
code. So switch to do it the same that x86 currently does PIT locking.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
