If a fixed-link DT subnode is used, the phy_device was looked up so
that a PHY ID string could be constructed and passed to phy_connect().
This is not necessary, as the device_node can be passed directly to
of_phy_connect() instead. This reuses the same codepath as if the
phy-handle DT property was used.
Signed-off-by: David Rivshin <drivshin@allworx.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy-mode emac property was only being processed in the phy_id
or fixed-link cases. However if phy-handle was specified instead,
an error message would complain about the lack of phy_id or
fixed-link, and then jump past the of_get_phy_mode(). This would
result in the PHY mode defaulting to MII, regardless of what the
devicetree specified.
Fixes: 9e42f71526 ("drivers: net: cpsw: add phy-handle parsing")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an emac node has a phy-handle property that points to something
which is not a phy, then a segmentation fault will occur when the
interface is brought up. This is because while phy_connect() will
return ERR_PTR() on failure, of_phy_connect() will return NULL.
The common error check uses IS_ERR(), and so missed when
of_phy_connect() fails. The NULL pointer is then dereferenced.
Also, the common error message referenced slave->data->phy_id,
which would be empty in the case of phy-handle. Instead, use the
name of the device_node as a useful identifier. And in the phy_id
case add the error code for completeness.
Fixes: 9e42f71526 ("drivers: net: cpsw: add phy-handle parsing")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9e42f71526 ("drivers: net: cpsw: add
phy-handle parsing") saved the "phy-handle" phandle into a new cpsw_priv
field. However, phy connections are per-slave, so the phy_node field should
be in cpsw_slave_data rather than cpsw_priv.
This would go unnoticed in a single emac configuration. But in dual_emac
mode, the last "phy-handle" property parsed for either slave would be used
by both of them, causing them both to refer to the same phy_device.
Fixes: 9e42f71526 ("drivers: net: cpsw: add phy-handle parsing")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default Pegasus setup was to append the status and CRC at the end of each
received packet. The status bits are used to update various stats, but CRC has
been ignored. The new default is to not append CRC at the end of RX packets.
Signed-off-by: Petko Manolov <petkan@mip-labs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
usb_fill_bulk_urb() receives buffer length parameter 8 bytes larger
than what's allocated by alloc_skb(); This seems to be a problem with
older (pegasus usb-1.1) devices, which may silently return more data
than the maximal packet length.
Reported-by: Lincoln Ramsay <a1291762@gmail.com>
Signed-off-by: Petko Manolov <petkan@mip-labs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 13a56b44 ("at803x: Add support for hardware reset") added a
work-around for a hardware bug on the AT8030. However, the work-around
was being called for all 803x PHYs, even those that don't need it.
Function at803x_link_change_notify() checks to make sure that it only
resets the PHY on the 8030, but it makes more sense to not call that
function at all if it isn't needed.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size allocated for target->hwinfo and the number of bytes copied in it
should be consistent.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
At forced 100 Full & Half duplex mode, chip may fail to set mode correctly
when cable is switched between long(~50+m) and short one.
As workaround, set to 10 before setting to 100 at forced 100 F/H mode.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix rx_bytes, tx_bytes and tx_frames error in netdev.stats.
- rx_bytes counted bytes excluding size of struct ethhdr.
- tx_packets didn't count multiple packets in a single urb
- tx_bytes included 8 bytes of extra commands.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error return err is not initialized and there is a possibility
that err is not assigned causing mv88e6xxx_port_bridge_join to
return a garbage error return status. Fix this by initializing err
to 0.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configured in fixed link, the DaVinci emac driver sets the
priv->phydev to NULL and further ioctl calls to the phy_mii_ioctl()
causes the kernel to crash.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Fixes: 1bb6aa56bb ("net: davinci_emac: Add support for fixed-link PHY")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath9k
* fix a couple release old throughput regression on ar9281
iwlwifi
* add new device IDs for 8265
* fix a NULL pointer dereference when paging firmware asserts
* remove a WARNING on gscan capabilities
* fix MODULE_FIRMWARE for 8260
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXHjlZAAoJEG4XJFUm622brcgIAJ127uU9S/X3oM2EK76TdbV+
yZnp8Te57bK+ypXRP7YMaL7gevR3q9TEzQkY6ZQ0iMCZenQouxB/Wg9xBZjJ/ny0
dlVtmwM2sSvYdieTSftKGWLg3FH0FaJ1VXCJirLwrbs4Hbi2FqcGKMrLxflpqgW2
m1FkTZzCbjokaHZgoWJmlDM/UbPtTz8BJgLICRd7hJ4jJ2Mi2k32LCSxsXn0GbUG
naS6bDUGBcKjly9PKomY9y+rj897lm/m3rGKFJPkX/T7Klb1UMBLCj8NQIyF+/AX
vu1fLxMwlFyXnmRJAFPyj9T2Vok3aDjRuA9xck3MufxOFjOhEGJiPjZV3wNNFj8=
=aDY4
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2016-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.6
ath9k
* fix a couple release old throughput regression on ar9281
iwlwifi
* add new device IDs for 8265
* fix a NULL pointer dereference when paging firmware asserts
* remove a WARNING on gscan capabilities
* fix MODULE_FIRMWARE for 8260
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When certain firmware variants are selected (via the sfboot utility) the
SFC7000 and SFC8000 series NICs don't support RSS. The driver still
tries (and fails) to insert filters with the RSS flag, and the NIC fails
to pass traffic.
When the firmware reports RSS_LIMITED suppress allocating a default RSS
context. The absence of an RSS context is picked up in filter insertion
and RSS flags are discarded.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_disable() can not be called with bh disabled, move locking just
around myri10ge_ss_lock_napi() .
Patches fixes following bug:
[ 114.278378] BUG: sleeping function called from invalid context at net/core/dev.c:4383
<snip>
[ 114.313712] Call Trace:
[ 114.314943] [<ffffffff817010ce>] dump_stack+0x19/0x1b
[ 114.317673] [<ffffffff810ce7f3>] __might_sleep+0x173/0x230
[ 114.320566] [<ffffffff815b3117>] napi_disable+0x27/0x90
[ 114.323254] [<ffffffffa01e437f>] myri10ge_close+0xbf/0x3f0 [myri10ge]
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Hyong-Youb Kim <hykim@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If PAGE_SIZE is bigger than BNXT_RX_PAGE_SIZE, that means the native CPU
page is bigger than the maximum length of the RX BD. Divide the page
into multiple 32K buffers for the aggregation ring.
Add an offset field in the bnxt_sw_rx_agg_bd struct to keep track of the
page offset of each buffer. Since each page can be referenced by multiple
buffer entries, call get_page() as needed to get the proper reference
count.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX BD length field of this device is 16-bit, so the largest buffer
size is 65535. For LRO and GRO, we allocate native CPU pages for the
aggregation ring buffers. It won't work if the native CPU page size is
64K or bigger.
We fix this by defining BNXT_RX_PAGE_SIZE to be native CPU page size
up to 32K. Replace PAGE_SIZE with BNXT_RX_PAGE_SIZE in all appropriate
places related to the rx aggregation ring logic.
The next patch will add additional logic to divide the page into 32K
chunks for aggrgation ring buffers if PAGE_SIZE is bigger than
BNXT_RX_PAGE_SIZE.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only MSI-X can be used on a VF. The driver should fail initialization
if it cannot successfully enable MSI-X.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When multiple skb are TX-completed in a row, we might incorrectly keep
a timestamp of a prior skb and cause extra work.
Fixes: ec693d4701 ("net/mlx4_en: Add HW timestamping (TS) support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces kexec support for mlx5.
When switching kernels, kexec() calls shutdown, which unloads
the driver and cleans its resources.
In addition, remove unregister netdev from shutdown flow. This will
allow a clean shutdown, even if some netdev clients did not release their
reference from this netdev. Releasing The HW resources only is enough as
the kernel is shutting down
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The static is not required and breaks re-entrancy if it will be required.
Fixes: 2530236303 ("net/mlx5_core: Flow steering tree initialization")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set and report vport MTU rather than physical MTU,
Driver will set both vport and physical port mtu and will
rely on the query of vport mtu.
SRIOV VFs have to report their MTU to their vport manager (PF),
and this will allow them to work with any MTU they need
without failing the request.
Also for some cases where the PF is not a port owner, PF can
work with MTU less than the physical port mtu if set physical
port mtu didn't take effect.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minimum MTU that can be set in Connectx4 device is 68.
This fixes the case where a user wants to set invalid MTU,
the driver will fail to satisfy this request and the interface
will stay down.
It is better to report an error and continue working with old
mtu.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For set/query MTU port firmware commands the MTU field
is 16 bits, here I changed all the "int mtu" parameters
of the functions wrapping those firmware commands to be u16.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the upcoming ConnectX-5 devices (PF and VF) to the list of
supported devices by the mlx5 driver.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bit 25 of eth_proto_capability in PTYS register is
1000Base-TT and not 100Base-T.
Fixes: f62b8bb8f2 ('net/mlx5: Extend mlx5_core to
support ConnectX-4 Ethernet functionality')
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the error flow of adding flow rule to auto-grouped flow
table, we call to tree_remove_node.
tree_remove_node locks the node's parent, however the node's parent
is already locked by mlx5_add_flow_rule and this causes a deadlock.
After this patch, if we failed to add the flow rule, we unlock the
flow table before calling to tree_remove_node.
fixes: f0d22d1874 ('net/mlx5_core: Introduce flow steering autogrouped
flow table')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reported-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just updating the version as many fixes got
accumulated over 5.3.63
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both socfpga_dwmac_parse_data() in dwmac-socfpga.c and stmmac_dvr_probe()
in stmmac_main.c functions call devm_reset_control_get() to register an
reset controller for the stmmac. This results in an attempt to register
two reset controllers for the same non-shared reset line.
The first attempt to register the reset controller works fine. The second
attempt fails with warning from the reset controller core, see below.
The warning is produced because the reset line is non-shared and thus
it is allowed to have only up-to one reset controller associated with
that reset line, not two or more.
The solution has multiple parts. First, the original socfpga_dwmac_init()
is tweaked to use reset controller pointer from the stmmac_priv (private
data of the stmmac core) instead of the local instance, which was used
before. The local re-registration of the reset controller is removed.
Next, the socfpga_dwmac_init() is moved after stmmac_dvr_probe() in the
probe function. This order is legal according to Altera and it makes the
code much easier, since there is no need to temporarily register and
unregister the reset controller ; the reset controller is already registered
by the stmmac_dvr_probe().
Finally, plat_dat->exit and socfpga_dwmac_exit() is no longer necessary,
since the functionality is already performed by the stmmac core.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at drivers/reset/core.c:187 __of_reset_control_get+0x218/0x270
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.6.0-rc4-next-20160419-00015-gabb2477-dirty #4
Hardware name: Altera SOCFPGA
[<c010f290>] (unwind_backtrace) from [<c010b82c>] (show_stack+0x10/0x14)
[<c010b82c>] (show_stack) from [<c0373da4>] (dump_stack+0x94/0xa8)
[<c0373da4>] (dump_stack) from [<c011bcc0>] (__warn+0xec/0x104)
[<c011bcc0>] (__warn) from [<c011bd88>] (warn_slowpath_null+0x20/0x28)
[<c011bd88>] (warn_slowpath_null) from [<c03a6eb4>] (__of_reset_control_get+0x218/0x270)
[<c03a6eb4>] (__of_reset_control_get) from [<c03a701c>] (__devm_reset_control_get+0x54/0x90)
[<c03a701c>] (__devm_reset_control_get) from [<c041fa30>] (stmmac_dvr_probe+0x1b4/0x8e8)
[<c041fa30>] (stmmac_dvr_probe) from [<c04298c8>] (socfpga_dwmac_probe+0x1b8/0x28c)
[<c04298c8>] (socfpga_dwmac_probe) from [<c03d6ffc>] (platform_drv_probe+0x4c/0xb0)
[<c03d6ffc>] (platform_drv_probe) from [<c03d54ec>] (driver_probe_device+0x224/0x2bc)
[<c03d54ec>] (driver_probe_device) from [<c03d5630>] (__driver_attach+0xac/0xb0)
[<c03d5630>] (__driver_attach) from [<c03d382c>] (bus_for_each_dev+0x6c/0xa0)
[<c03d382c>] (bus_for_each_dev) from [<c03d4ad4>] (bus_add_driver+0x1a4/0x21c)
[<c03d4ad4>] (bus_add_driver) from [<c03d60ac>] (driver_register+0x78/0xf8)
[<c03d60ac>] (driver_register) from [<c0101760>] (do_one_initcall+0x40/0x170)
[<c0101760>] (do_one_initcall) from [<c0800e38>] (kernel_init_freeable+0x1dc/0x27c)
[<c0800e38>] (kernel_init_freeable) from [<c05d1bd4>] (kernel_init+0x8/0x114)
[<c05d1bd4>] (kernel_init) from [<c01076f8>] (ret_from_fork+0x14/0x3c)
---[ end trace 059d2fbe87608fa9 ]---
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Matthew Gerlach <mgerlach@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: David S. Miller <davem@davemloft.net>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macsec_validate_attr should check IFLA_MACSEC_REPLAY_PROTECT (not
IFLA_MACSEC_PROTECT) to verify that the replay protection and replay
window arguments are correct.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I accidentally forgot some MACSEC_ prefixes in if_macsec.h.
Fixes: dece8d2b78 ("uapi: add MACsec bits")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We leak a struct macsec_rxh_data when we unregister the rx_handler in
macsec_dellink.
We also leak a struct macsec_rxh_data in register_macsec_dev if we fail
to register the rx_handler.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use genl_dump_check_consistent in dump_secy.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The decrypt callback macsec_decrypt_done needs a reference on the rx_sa
and releases it before returning, but macsec_handle_frame already
put that reference after macsec_decrypt returned NULL.
Set rx_sa to NULL when the decrypt callback runs so that
macsec_handle_frame knows it must not release the reference.
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "deliver:" path of macsec_handle_frame can be called with
rx_sa == NULL. Check rx_sa != NULL before calling macsec_rxsa_put().
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: c09440f7dc ("macsec: introduce IEEE 802.1AE driver")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix memory leak in iwlwifi, from Matti Gottlieb.
2) Add missing registration of netfilter arp_tables into initial
namespace, from Florian Westphal.
3) Fix potential NULL deref in DecNET routing code.
4) Restrict NETLINK_URELEASE to truly bound sockets only, from Dmitry
Ivanov.
5) Fix dst ref counting in VRF, from David Ahern.
6) Fix TSO segmenting limits in i40e driver, from Alexander Duyck.
7) Fix heap leak in PACKET_DIAG_MCLIST, from Mathias Krause.
8) Ravalidate IPV6 datagram socket cached routes properly, particularly
with UDP, from Martin KaFai Lau.
9) Fix endian bug in RDS dp_ack_seq handling, from Qing Huang.
10) Fix stats typing in bcmgenet driver, from Eric Dumazet.
11) Openvswitch needs to orphan SKBs before ipv6 fragmentation handing,
from Joe Stringer.
12) SPI device reference leak in spi_ks8895 PHY driver, from Mark Brown.
13) atl2 doesn't actually support scatter-gather, so don't advertise the
feature. From Ben Hucthings.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (72 commits)
openvswitch: use flow protocol when recalculating ipv6 checksums
Driver: Vmxnet3: set CHECKSUM_UNNECESSARY for IPv6 packets
atl2: Disable unimplemented scatter/gather feature
net/mlx4_en: Split SW RX dropped counter per RX ring
net/mlx4_core: Don't allow to VF change global pause settings
net/mlx4_core: Avoid repeated calls to pci enable/disable
net/mlx4_core: Implement pci_resume callback
net: phy: spi_ks8895: Don't leak references to SPI devices
net: ethernet: davinci_emac: Fix platform_data overwrite
net: ethernet: davinci_emac: Fix Unbalanced pm_runtime_enable
qede: Fix single MTU sized packet from firmware GRO flow
qede: Fix setting Skb network header
qede: Fix various memory allocation error flows for fastpath
tcp: Merge tx_flags and tskey in tcp_shifted_skb
tcp: Merge tx_flags and tskey in tcp_collapse_retrans
drivers: net: cpsw: fix wrong regs access in cpsw_ndo_open
tcp: Fix SOF_TIMESTAMPING_TX_ACK when handling dup acks
openvswitch: Orphan skbs before IPv6 defrag
Revert "Prevent NUll pointer dereference with two PHYs on cpsw"
VSOCK: Only check error on skb_recv_datagram when skb is NULL
...
For IPv6, if the device indicates that the checksum is correct, set
CHECKSUM_UNNECESSARY.
Reported-by: Subbarao Narahari <snarahari@vmware.com>
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: Jin Heo <heoj@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
atl2 includes NETIF_F_SG in hw_features even though it has no support
for non-linear skbs. This bug was originally harmless since the
driver does not claim to implement checksum offload and that used to
be a requirement for SG.
Now that SG and checksum offload are independent features, if you
explicitly enable SG *and* use one of the rare protocols that can use
SG without checkusm offload, this potentially leaks sensitive
information (before you notice that it just isn't working). Therefore
this obscure bug has been designated CVE-2016-2117.
Reported-by: Justin Yackoski <jyackoski@crypto-nite.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: ec5f061564 ("net: Kill link between CSUM and SG features.")
Signed-off-by: David S. Miller <davem@davemloft.net>
Count SW packet drops per RX ring instead of a global counter. This
will allow monitoring the number of rx drops per ring.
In addition, SW rx_dropped counter was overwritten by HW rx_dropped
counter, sum both of them instead to show the accurate value.
Fixes: a3333b35da ('net/mlx4_en: Moderate ethtool callback to [...] ')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reported-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently changing global pause settings is done via SET_PORT
command with input modifier GENERAL. This command is allowed
for each VF since MTU setting is done via the same command.
Change the above to the following scheme: before passing the
request to the FW, the PF will check whether it was issued
by a slave. If yes, don't change global pause and warn,
otherwise change to the requested value and store for
further reference.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maintain the PCI status and provide wrappers for enabling and disabling
the PCI device. Performing the actions more than once without doing
its opposite results in warning logs.
This occurred when EEH hotplugged the device causing a warning for
disabling an already disabled device.
Fixes: 2ba5fbd62b ('net/mlx4_core: Handle AER flow properly')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move resume related activities to a new pci_resume function instead of
performing them in mlx4_pci_slot_reset. This change is needed to avoid
a hotplug during EEH recovery due to commit f2da4ccf8b ("powerpc/eeh:
More relaxed hotplug criterion").
Fixes: 2ba5fbd62b ('net/mlx4_core: Handle AER flow properly')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ks8895 driver is using spi_dev_get() apparently just to take a copy
of the SPI device used to instantiate it but never calls spi_dev_put()
to free it. Since the device is guaranteed to exist between probe() and
remove() there should be no need for the driver to take an extra
reference to it so fix the leak by just using a straight assignment.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the DaVinci emac driver is removed and re-probed, the actual
pdev->dev.platform_data is populated with an unwanted valid pointer saved by
the previous davinci_emac_of_get_pdata() call, causing a kernel crash when
calling priv->int_disable() in emac_int_disable().
Unable to handle kernel paging request at virtual address c8622a80
...
[<c0426fb4>] (emac_int_disable) from [<c0427700>] (emac_dev_open+0x290/0x5f8)
[<c0427700>] (emac_dev_open) from [<c04c00ec>] (__dev_open+0xb8/0x120)
[<c04c00ec>] (__dev_open) from [<c04c0370>] (__dev_change_flags+0x88/0x14c)
[<c04c0370>] (__dev_change_flags) from [<c04c044c>] (dev_change_flags+0x18/0x48)
[<c04c044c>] (dev_change_flags) from [<c052bafc>] (devinet_ioctl+0x6b4/0x7ac)
[<c052bafc>] (devinet_ioctl) from [<c04a1428>] (sock_ioctl+0x1d8/0x2c0)
[<c04a1428>] (sock_ioctl) from [<c014f054>] (do_vfs_ioctl+0x41c/0x600)
[<c014f054>] (do_vfs_ioctl) from [<c014f2a4>] (SyS_ioctl+0x6c/0x7c)
[<c014f2a4>] (SyS_ioctl) from [<c000ff60>] (ret_fast_syscall+0x0/0x1c)
Fixes: 42f59967a0 ("net: ethernet: davinci_emac: add OF support")
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid an Unbalanced pm_runtime_enable in the DaVinci
emac driver when the device is removed and re-probed, and a
pm_runtime_disable() call in davinci_emac_remove().
Actually, using unbind/bind on a TI DM8168 SoC gives :
$ echo 4a120000.ethernet > /sys/bus/platform/drivers/davinci_emac/unbind
net eth1: DaVinci EMAC: davinci_emac_remove()
$ echo 4a120000.ethernet > /sys/bus/platform/drivers/davinci_emac/bind
davinci_emac 4a120000.ethernet: Unbalanced pm_runtime_enable
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Fixes: 3ba9738134 ("net: ethernet: davinci_emac: add pm_runtime support")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In firmware assisted GRO flow there could be a single MTU sized
segment arriving due to firmware aggregation timeout/last segment
in an aggregation flow, which is not expected to be an actual gro
packet. So If a skb has zero frags from the GRO flow then simply
push it in the stack as non gso skb.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <yuval.mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
