ADS7846 regulator is disabled twice in a row in ads7846_remove(). Valid
one is in ads7846_disable().
Removing the ads7846 module causes warning about unbalanced disables.
...
WARNING: CPU: 0 PID: 29269 at drivers/regulator/core.c:2251 _regulator_disable+0xf8/0x130
unbalanced disables for vads7846
CPU: 0 PID: 29269 Comm: rmmod Tainted: G D W 4.7.0+ #3
Hardware name: HTC Magician
...
show_stack+0x10/0x14
__warn+0xd8/0x100
warn_slowpath_fmt+0x38/0x48
_regulator_disable+0xf8/0x130
regulator_disable+0x34/0x60
ads7846_remove+0x58/0xd4 [ads7846]
spi_drv_remove+0x1c/0x34
__device_release_driver+0x84/0x114
driver_detach+0x8c/0x90
bus_remove_driver+0x5c/0xc8
SyS_delete_module+0x1a0/0x238
ret_fast_syscall+0x0/0x38
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The map_offset variable is specific to the register and needs to be reset
in the loop. Otherwise, subsequent register's subpacket maps will have
their bits set at the wrong index.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Tested-by: Nitin Chaudhary <nitinchaudhary1289@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit fe6b0dfaba ("Input: tegra-kbc - use reset framework")
accidentally converted _deassert to _assert, so there is no code
to wake up this hardware.
Fixes: fe6b0dfaba ("Input: tegra-kbc - use reset framework")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The silead code is using devm_foo for everything (and does not free
any resources). Except that it is using gpiod_get instead of
devm_gpiod_get (but is not freeing the gpio_desc), change this
to use devm_gpiod_get so that the gpio will be properly released.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The i40iw initiator sends an MPA-request with ird=16 and ord=16. The cxgb4
responder sends an MPA-reply with ord = 32 causing i40iw to terminate
due to insufficient resources.
The logic to reduce the ORD to <= peer's IRD was wrong.
Reported-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The i40iw initiator sends an MPA-request with ird = 63, ord = 63. The
cxgb4 responder sends a RST. Since the inbound ord=63 and it exceeds
the max_ird/c4iw_max_read_depth (=32 default), chelsio decides to abort.
Instead, cxgb4 should adjust the ord/ird down before presenting it to
the ULP.
Reported-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The unwind logic for creating a user QP has a double vfree
of the non-shared receive queue when handling a "too many qps"
failure.
The code unwinds the mmmap info by decrementing a reference
count which will call rvt_release_mmap_info() which in turn
does the vfree() of the r_rq.wq. The unwind code then does
the same free.
Fix by guarding the vfree() with the same test that is done
in close and only do the vfree() if qp->ip is NULL.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Previously, J_KEY generation was based on the lower 16 bits
of the user's UID. While this works, it was not good enough
as a non-root user could collide with a root user given a
sufficiently large UID.
This patch attempt to improve the J_KEY generation by using
the following algorithm:
The 16 bit J_KEY space is partitioned into 3 separate spaces
reserved for different user classes:
* all users with administtor privileges (including 'root')
will use J_KEYs in the range of 0 to 31,
* all kernel protocols, which use KDETH packets will use
J_KEYs in the range of 32 to 63, and
* all other users will use J_KEYs in the range of 64 to
65535.
The above separation is aimed at preventing different user levels
from sending packets to each other and, additionally, separate
kernel protocols from all other types of users. The later is meant
to prevent the potential corruption of kernel memory by any other
type of user.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The driver does not check if the CableInfo query is supported for the
port type. Return early if CableInfo is not supported for the port type,
making compliance with the specification explicit and preventing lower
level code from potentially doing the wrong thing if the query is not
supported for the hardware implementation.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The Soft RoCE (rxe) is located in drivers/inifiniband/sw
and not in drivers/infiniband/hw/.
This patch fixes it.
Fixes: 8700e3e7c4 ("Soft RoCE driver")
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If 'pci_register_driver' fails, we return 'err' which is known to be 0.
Return the error instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Doug Ledford <dledford@redhat.com>
It is likely that checking the result of 'setup_ctxt' is expected here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The callback function of call_rcu() just calls a kfree(), so we
can use kfree_rcu() instead of call_rcu() + callback function.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Validate the etype to insure that the header is correct.
Reviewed-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The "packet" parameter was being passed on the stack,
change it to a pointer.
Reviewed-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The monitor values from bytes 22 through 81 of the QSFP memory space
(SFF 8636) are dynamic and serving them out of the QSFP memory cache
maintained by the driver provides stale data to the CableInfo SMA query.
This patch refreshes the dynamic values from the QSFP memory on request
and overwrites the stale data from the cache for the overlap between the
requested range and the monitor range.
Reviewed-by: Jubin John <jubin.john@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The qp init function does a kzalloc() while holding the RCU
lock that encounters the following warning with a debug kernel
when a cat of the qp_stats is done:
[ 231.723948] rcu_scheduler_active = 1, debug_locks = 0
[ 231.731939] 3 locks held by cat/11355:
[ 231.736492] #0: (debugfs_srcu){......}, at: [<ffffffff813001a5>] debugfs_use_file_start+0x5/0x90
[ 231.746955] #1: (&p->lock){+.+.+.}, at: [<ffffffff81289a6c>] seq_read+0x4c/0x3c0
[ 231.755873] #2: (rcu_read_lock){......}, at: [<ffffffffa0a0c535>] _qp_stats_seq_start+0x5/0xd0 [hfi1]
[ 231.766862]
The init functions do an implicit next which requires the rcu read lock
before the kzalloc().
Fix for both drivers is to change the scope of the init function to only
do the allocation and the initialization of the just allocated iter.
The implict next is moved back into the respective start functions to fix
the issue.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
CC: <stable@vger.kernel.org> # 4.6.x-
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix to return error code -ENOMEM from the alloc error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
'work' and 'route->path_rec' are malloced in cma_resolve_iboe_route()
and should be freed before leaving from the error handling cases,
otherwise it will cause memory leak.
Fixes: 200298326b ('IB/core: Validate route when we init ah')
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Reviewed-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If CONFIG_FRAME_WARN is small (1K) and CONFIG_NR_CPUS big
then a frame size warning is triggered during build.
Allocate the cpu mask dynamically to silence the warning.
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Error code EAGAIN should be used when errors are temporary and next call
might succeeds.
When error code other than EAGAIN is returned, the caller (mlx4_ib_poll)
will assume all CQE in the same bunch are error too and will drop them all.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
No need to return int if function always returns 0
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If an IRQ is setup using __setup_irq(), which is used by the
request_irq() family of functions, and we are using an SMP kernel then
the affinity of the IRQ will be set via setup_affinity() immediately
after the IRQ is enabled. This call to gic_set_affinity() will lead to
the interrupt being mapped to a VPE. However there are other ways to use
IRQs which don't cause affinity to be set, for example if it is used to
chain to another IRQ controller with irq_set_chained_handler_and_data().
The irq_set_chained_handler_and_data() code path will enable the IRQ,
but will not trigger a call to gic_set_affinity() and in this case
nothing will map the interrupt to a VPE, meaning that the interrupt is
never received.
Fix this by implementing the activate operation for the GIC device IRQ
domain, using gic_shared_irq_domain_map() to map the interrupt to the
correct pin of cpu 0.
Fixes: c98c1822ee ("irqchip/mips-gic: Add device hierarchy domain")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20160819170715.27820-2-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
gic_shared_irq_domain_map() is called from gic_irq_domain_alloc() where
the wrong chip has been set, and is then overwritten. Tidy this up by
setting the correct chip the first time, and setting the
handle_level_irq handler from gic_irq_domain_alloc() too.
gic_shared_irq_domain_map() is also called from gic_irq_domain_map(),
which now calls irq_set_chip_and_handler() to retain its previous
behaviour.
This patch prepares for a follow-on which will call
gic_shared_irq_domain_map() from a callback where the lock on the struct
irq_desc is held, which without this change would cause the call to
irq_set_chip_and_handler() to lead to a deadlock.
Fixes: c98c1822ee ("irqchip/mips-gic: Add device hierarchy domain")
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20160819170715.27820-1-paul.burton@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If we're enabling a pipe, we'll need to modify the watermarks on all
active planes. Since those planes won't be added to the state on
their own, we need to add them ourselves.
Signed-off-by: Lyude <cpaul@redhat.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471463761-26796-6-git-send-email-cpaul@redhat.com
(cherry picked from commit 05a76d3d6a)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When we write watermark values to the hardware, those values are stored
in dev_priv->wm.skl_hw. However with recent watermark changes, the
results structure we're copying from only contains valid watermark and
DDB values for the pipes that are actually changing; the values for
other pipes remain 0. Thus a blind copy of the entire skl_wm_values
structure will clobber the values for unchanged pipes...we need to be
more selective and only copy over the values for the changing pipes.
This mistake was hidden until recently due to another bug that caused us
to erroneously re-calculate watermarks for all active pipes rather than
changing pipes. Only when that bug was fixed was the impact of this bug
discovered (e.g., modesets failing with "Requested display configuration
exceeds system watermark limitations" messages and leaving watermarks
non-functional, even ones initiated by intel_fbdev_restore_mode).
Changes since v1:
- Add a function for copying a pipe's wm values
(skl_copy_wm_for_pipe()) so we can reuse this later
Fixes: 734fa01f3a ("drm/i915/gen9: Calculate watermarks during atomic 'check' (v2)")
Fixes: 9b61302274 ("drm/i915/gen9: Re-allocate DDB only for changed pipes")
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lyude <cpaul@redhat.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Cc: stable@vger.kernel.org
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471463761-26796-4-git-send-email-cpaul@redhat.com
(cherry picked from commit 2722efb90b)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Since the watermark calculations for Skylake are still broken, we're apt
to hitting underruns very easily under multi-monitor configurations.
While it would be lovely if this was fixed, it's not. Another problem
that's been coming from this however, is the mysterious issue of
underruns causing full system hangs. An easy way to reproduce this with
a skylake system:
- Get a laptop with a skylake GPU, and hook up two external monitors to
it
- Move the cursor from the built-in LCD to one of the external displays
as quickly as you can
- You'll get a few pipe underruns, and eventually the entire system will
just freeze.
After doing a lot of investigation and reading through the bspec, I
found the existence of the SAGV, which is responsible for adjusting the
system agent voltage and clock frequencies depending on how much power
we need. According to the bspec:
"The display engine access to system memory is blocked during the
adjustment time. SAGV defaults to enabled. Software must use the
GT-driver pcode mailbox to disable SAGV when the display engine is not
able to tolerate the blocking time."
The rest of the bspec goes on to explain that software can simply leave
the SAGV enabled, and disable it when we use interlaced pipes/have more
then one pipe active.
Sure enough, with this patchset the system hangs resulting from pipe
underruns on Skylake have completely vanished on my T460s. Additionally,
the bspec mentions turning off the SAGV with more then one pipe enabled
as a workaround for display underruns. While this patch doesn't entirely
fix that, it looks like it does improve the situation a little bit so
it's likely this is going to be required to make watermarks on Skylake
fully functional.
This will still need additional work in the future: we shouldn't be
enabling the SAGV if any of the currently enabled planes can't enable WM
levels that introduce latencies >= 30 µs.
Changes since v11:
- Add skl_can_enable_sagv()
- Make sure we don't enable SAGV when not all planes can enable
watermarks >= the SAGV engine block time. I was originally going to
save this for later, but I recently managed to run into a machine
that was having problems with a single pipe configuration + SAGV.
- Make comparisons to I915_SKL_SAGV_NOT_CONTROLLED explicit
- Change I915_SAGV_DYNAMIC_FREQ to I915_SAGV_ENABLE
- Move printks outside of mutexes
- Don't print error messages twice
Changes since v10:
- Apparently sandybridge_pcode_read actually writes values and reads
them back, despite it's misleading function name. This means we've
been doing this mostly wrong and have been writing garbage to the
SAGV control. Because of this, we no longer attempt to read the SAGV
status during initialization (since there are no helpers for this).
- mlankhorst noticed that this patch was breaking on some very early
pre-release Skylake machines, which apparently don't allow you to
disable the SAGV. To prevent machines from failing tests due to SAGV
errors, if the first time we try to control the SAGV results in the
mailbox indicating an invalid command, we just disable future attempts
to control the SAGV state by setting dev_priv->skl_sagv_status to
I915_SKL_SAGV_NOT_CONTROLLED and make a note of it in dmesg.
- Move mutex_unlock() a little higher in skl_enable_sagv(). This
doesn't actually fix anything, but lets us release the lock a little
sooner since we're finished with it.
Changes since v9:
- Only enable/disable sagv on Skylake
Changes since v8:
- Add intel_state->modeset guard to the conditional for
skl_enable_sagv()
Changes since v7:
- Remove GEN9_SAGV_LOW_FREQ, replace with GEN9_SAGV_IS_ENABLED (that's
all we use it for anyway)
- Use GEN9_SAGV_IS_ENABLED instead of 0x1 for clarification
- Fix a styling error that snuck past me
Changes since v6:
- Protect skl_enable_sagv() with intel_state->modeset conditional in
intel_atomic_commit_tail()
Changes since v5:
- Don't use is_power_of_2. Makes things confusing
- Don't use the old state to figure out whether or not to
enable/disable the sagv, use the new one
- Split the loop in skl_disable_sagv into it's own function
- Move skl_sagv_enable/disable() calls into intel_atomic_commit_tail()
Changes since v4:
- Use is_power_of_2 against active_crtcs to check whether we have > 1
pipe enabled
- Fix skl_sagv_get_hw_state(): (temp & 0x1) indicates disabled, 0x0
enabled
- Call skl_sagv_enable/disable() from pre/post-plane updates
Changes since v3:
- Use time_before() to compare timeout to jiffies
Changes since v2:
- Really apply minor style nitpicks to patch this time
Changes since v1:
- Added comments about this probably being one of the requirements to
fixing Skylake's watermark issues
- Minor style nitpicks from Matt Roper
- Disable these functions on Broxton, since it doesn't have an SAGV
Signed-off-by: Lyude <cpaul@redhat.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471463761-26796-3-git-send-email-cpaul@redhat.com
[mlankhorst: ENOSYS -> ENXIO, whitespace fixes]
(cherry picked from commit 656d1b89e5)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In order to add proper support for the SAGV, we need to be able to know
what the cause of a failure to change the SAGV through the pcode mailbox
was. The reasoning for this is that some very early pre-release Skylake
machines don't actually allow you to control the SAGV on them, and
indicate an invalid mailbox command was sent.
This also might come in handy in the future for debugging.
Changes since v1:
- Add functions for interpreting gen6 mailbox error codes along with
gen7+ error codes, and actually interpret those codes properly
- Renamed patch to reflect new behavior
Signed-off-by: Lyude <cpaul@redhat.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471463761-26796-2-git-send-email-cpaul@redhat.com
[mlankhorst: -ENOSYS -> -ENXIO for checkpatch]
(cherry picked from commit 87660502f1)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In the recent patch
bc3d674 drm/i915: Allow userspace to request no-error-capture upon ...
the final version moved the flags and the associated #defines around
so they were adjacent; unfortunately, they ended up between a comment
and the thing (hw_id) to which the comment applies :(
So this patch reshuffles the comment and subject back together.
Also, as we're touching 'hw_id', let's change it from just 'unsigned'
to a fully-specified 'unsigned int', because some code checking tools
(including checkpatch) object to plain 'unsigned'.
Fixes: bc3d674462 ("drm/i915: Allow userspace to request no-error-capture...")
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1471616622-6919-1-git-send-email-david.s.gordon@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 0be81156b3)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
If userspace is asynchronously streaming into the batch or other
execobjects, we may not flush those writes along with a change in cache
domain (as there is no change). Therefore those writes may end up in
internal chipset buffers and not visible to the GPU upon execution. We
must issue a flush command or otherwise we encounter incoherency in the
batchbuffers and the GPU executing invalid commands (i.e. hanging) quite
regularly.
v2: Throw a paranoid wmb() into the general flush so that we remain
consistent with before.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90841
Fixes: 1816f92363 ("drm/i915: Support creation of unbound wc user...")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Akash Goel <akash.goel@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Tested-by: Matti Hämäläinen <ccr@tnsp.org>
Cc: stable@vger.kernel.org
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160818161718.27187-1-chris@chris-wilson.co.uk
(cherry picked from commit 600f436801)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
It's possible to have a non-zero plane mask and still wind up with a
total data rate of zero. There are two cases where this can happen:
* planes are active (from the KMS point of view), but are
all fully clipped (positioned offscreen)
* the only active plane on a CRTC is the cursor (which is handled
independently and not counted into the general data rate computations
These are both valid display setups (although unusual), so we need to
drop the WARN().
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Testcase: kms_universal_planes.cursor-only-pipe-*
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466196140-16336-4-git-send-email-matthew.d.roper@intel.com
Cc: stable@vger.kernel.org #v4.7+
(cherry picked from commit 43aa7e8750)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
intel_state->active_crtcs is usually only initialized when doing a
modeset. During our first atomic commit after boot, we're effectively
faking a modeset to sanitize the DDB/wm setup, so ensure that this field
gets initialized before use.
v2:
- Don't clobber active_crtcs if our first commit really is a modeset
(Maarten)
- Grab connection_mutex when faking a modeset during sanitization
(Maarten)
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466196140-16336-2-git-send-email-matthew.d.roper@intel.com
Cc: stable@vger.kernel.org #v4.7+
(cherry picked from commit 1b54a880b2)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The commit 02fc76f6a changed base of the sysfs attributes from device to card.
The "show" callbacks dereferenced wrong objects because of this.
Fixes: 02fc76f6a7 ('ALSA: line6: Create sysfs via snd_card_add_dev_attr()')
Cc: <stable@vger.kernel.org> # v4.0+
Reviewed-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Andrej Krutak <dev@andree.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If there's an error, pcm is released in line6_pcm_acquire already.
Fixes: 247d95ee6d ('ALSA: line6: Handle error from line6_pcm_acquire()')
Cc: <stable@vger.kernel.org> # v4.0+
Reviewed-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Andrej Krutak <dev@andree.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Without locking out CPU mask operations we might end up with an inconsistent
view of the cpumask in the function.
Fixes: 5e385a6ef3: "genirq: Add a helper to spread an affinity mask for MSI/MSI-X vectors"
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/1470924405-25728-1-git-send-email-hch@lst.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Obviously we should free action here if irq_chip_pm_get failed.
Fixes: be45beb2df: "genirq: Add runtime power management support for IRQ chips"
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/1471854112-13006-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- A critical fix for chained irqchip where we failed to configure
the cascade interrupt trigger
- A GIC fix for self-IPI in SMP-on-UP configurations
- A PM fix for GICv3
- A initialization fix the the GICv3 ITS, triggered by kexec
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vmKj
-----END PGP SIGNATURE-----
Merge tag 'irqchip-for-4.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull genirq/irqchip fixes for 4.8-rc4 from Marc Zygnier
- A critical fix for chained irqchip where we failed to configure
the cascade interrupt trigger
- A GIC fix for self-IPI in SMP-on-UP configurations
- A PM fix for GICv3
- A initialization fix the the GICv3 ITS, triggered by kexec
Somehow this one slipped through, which means drivers without modeset
support can be oopsed (since those also don't call
drm_mode_config_init, which means the crtc lookup will chase an
uninitalized idr).
Reported-by: Alexander Potapenko <glider@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull two parisc fixes from Helge Deller:
"The first patch ensures that the high-res cr16 clocksource (which was
added in kernel 4.7) gets choosen as default clocksource for parisc.
The second patch moves the #define of EREFUSED down inside errno.h and
thus unbreaks building the gccgo compiler"
* 'parisc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix order of EREFUSED define in errno.h
parisc: Fix automatic selection of cr16 clocksource
This is an entirely new driver instead of yet another set of patches
to sb_edac.c because:
1) Mapping from PCI devices to socket/memory controller is significantly
different. Skylake scatters devices on a socket across a number of
PCI buses.
2) There is an extra level of interleaving via the "mcroute" register
that would be a little messy to squeeze into the old driver.
3) Validation is getting too expensive. Changes to sb_edac need to
be checked against Sandy Bridge, Ivy Bridge, Haswell, Broadwell and
Knights Landing.
Acked-by: Aristeu Rozanski <aris@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When building gccgo in userspace, errno.h gets parsed and the go include file
sysinfo.go is generated.
Since EREFUSED is defined to the same value as ECONNREFUSED, and ECONNREFUSED
is defined later on in errno.h, this leads to go complaining that EREFUSED
isn't defined yet.
Fix this trivial problem by moving the define of EREFUSED down after
ECONNREFUSED in errno.h (and clean up the indenting while touching this line).
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org
Commit 54b6680090 (parisc: Add native high-resolution sched_clock()
implementation) added support to use the CPU-internal cr16 counters as reliable
clocksource with the help of HAVE_UNSTABLE_SCHED_CLOCK.
Sadly the commit missed to remove the hack which prevented cr16 to become the
default clocksource even on SMP systems.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 4.7+
