Pull SMP hotplug updates from Thomas Gleixner:
"This update is primarily a cleanup of the CPU hotplug locking code.
The hotplug locking mechanism is an open coded RWSEM, which allows
recursive locking. The main problem with that is the recursive nature
as it evades the full lockdep coverage and hides potential deadlocks.
The rework replaces the open coded RWSEM with a percpu RWSEM and
establishes full lockdep coverage that way.
The bulk of the changes fix up recursive locking issues and address
the now fully reported potential deadlocks all over the place. Some of
these deadlocks have been observed in the RT tree, but on mainline the
probability was low enough to hide them away."
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
cpu/hotplug: Constify attribute_group structures
powerpc: Only obtain cpu_hotplug_lock if called by rtasd
ARM/hw_breakpoint: Fix possible recursive locking for arch_hw_breakpoint_init
cpu/hotplug: Remove unused check_for_tasks() function
perf/core: Don't release cred_guard_mutex if not taken
cpuhotplug: Link lock stacks for hotplug callbacks
acpi/processor: Prevent cpu hotplug deadlock
sched: Provide is_percpu_thread() helper
cpu/hotplug: Convert hotplug locking to percpu rwsem
s390: Prevent hotplug rwsem recursion
arm: Prevent hotplug rwsem recursion
arm64: Prevent cpu hotplug rwsem recursion
kprobes: Cure hotplug lock ordering issues
jump_label: Reorder hotplug lock and jump_label_lock
perf/tracing/cpuhotplug: Fix locking order
ACPI/processor: Use cpu_hotplug_disable() instead of get_online_cpus()
PCI: Replace the racy recursion prevention
PCI: Use cpu_hotplug_disable() instead of get_online_cpus()
perf/x86/intel: Drop get_online_cpus() in intel_snb_check_microcode()
x86/perf: Drop EXPORT of perf_check_microcode
...
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle were:
- Add the SYSTEM_SCHEDULING bootup state to move various scheduler
debug checks earlier into the bootup. This turns silent and
sporadically deadly bugs into nice, deterministic splats. Fix some
of the splats that triggered. (Thomas Gleixner)
- A round of restructuring and refactoring of the load-balancing and
topology code (Peter Zijlstra)
- Another round of consolidating ~20 of incremental scheduler code
history: this time in terms of wait-queue nomenclature. (I didn't
get much feedback on these renaming patches, and we can still
easily change any names I might have misplaced, so if anyone hates
a new name, please holler and I'll fix it.) (Ingo Molnar)
- sched/numa improvements, fixes and updates (Rik van Riel)
- Another round of x86/tsc scheduler clock code improvements, in hope
of making it more robust (Peter Zijlstra)
- Improve NOHZ behavior (Frederic Weisbecker)
- Deadline scheduler improvements and fixes (Luca Abeni, Daniel
Bristot de Oliveira)
- Simplify and optimize the topology setup code (Lauro Ramos
Venancio)
- Debloat and decouple scheduler code some more (Nicolas Pitre)
- Simplify code by making better use of llist primitives (Byungchul
Park)
- ... plus other fixes and improvements"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (103 commits)
sched/cputime: Refactor the cputime_adjust() code
sched/debug: Expose the number of RT/DL tasks that can migrate
sched/numa: Hide numa_wake_affine() from UP build
sched/fair: Remove effective_load()
sched/numa: Implement NUMA node level wake_affine()
sched/fair: Simplify wake_affine() for the single socket case
sched/numa: Override part of migrate_degrades_locality() when idle balancing
sched/rt: Move RT related code from sched/core.c to sched/rt.c
sched/deadline: Move DL related code from sched/core.c to sched/deadline.c
sched/cpuset: Only offer CONFIG_CPUSETS if SMP is enabled
sched/fair: Spare idle load balancing on nohz_full CPUs
nohz: Move idle balancer registration to the idle path
sched/loadavg: Generalize "_idle" naming to "_nohz"
sched/core: Drop the unused try_get_task_struct() helper function
sched/fair: WARN() and refuse to set buddy when !se->on_rq
sched/debug: Fix SCHED_WARN_ON() to return a value on !CONFIG_SCHED_DEBUG as well
sched/wait: Disambiguate wq_entry->task_list and wq_head->task_list naming
sched/wait: Move bit_wait_table[] and related functionality from sched/core.c to sched/wait_bit.c
sched/wait: Split out the wait_bit*() APIs from <linux/wait.h> into <linux/wait_bit.h>
sched/wait: Re-adjust macro line continuation backslashes in <linux/wait.h>
...
- introduce the new uuid_t/guid_t types that are going to replace
the somewhat confusing uuid_be/uuid_le types and make the terminology
fit the various specs, as well as the userspace libuuid library.
(me, based on a previous version from Amir)
- consolidated generic uuid/guid helper functions lifted from XFS
and libnvdimm (Amir and me)
- conversions to the new types and helpers (Amir, Andy and me)
-----BEGIN PGP SIGNATURE-----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=J/4P
-----END PGP SIGNATURE-----
Merge tag 'uuid-for-4.13' of git://git.infradead.org/users/hch/uuid
Pull uuid subsystem from Christoph Hellwig:
"This is the new uuid subsystem, in which Amir, Andy and I have started
consolidating our uuid/guid helpers and improving the types used for
them. Note that various other subsystems have pulled in this tree, so
I'd like it to go in early.
UUID/GUID summary:
- introduce the new uuid_t/guid_t types that are going to replace the
somewhat confusing uuid_be/uuid_le types and make the terminology
fit the various specs, as well as the userspace libuuid library.
(me, based on a previous version from Amir)
- consolidated generic uuid/guid helper functions lifted from XFS and
libnvdimm (Amir and me)
- conversions to the new types and helpers (Amir, Andy and me)"
* tag 'uuid-for-4.13' of git://git.infradead.org/users/hch/uuid: (34 commits)
ACPI: hns_dsaf_acpi_dsm_guid can be static
mmc: sdhci-pci: make guid intel_dsm_guid static
uuid: Take const on input of uuid_is_null() and guid_is_null()
thermal: int340x_thermal: fix compile after the UUID API switch
thermal: int340x_thermal: Switch to use new generic UUID API
acpi: always include uuid.h
ACPI: Switch to use generic guid_t in acpi_evaluate_dsm()
ACPI / extlog: Switch to use new generic UUID API
ACPI / bus: Switch to use new generic UUID API
ACPI / APEI: Switch to use new generic UUID API
acpi, nfit: Switch to use new generic UUID API
MAINTAINERS: add uuid entry
tmpfs: generate random sb->s_uuid
scsi_debug: switch to uuid_t
nvme: switch to uuid_t
sysctl: switch to use uuid_t
partitions/ldm: switch to use uuid_t
overlayfs: use uuid_t instead of uuid_be
fs: switch ->s_uuid to uuid_t
ima/policy: switch to use uuid_t
...
* acpi-pmic:
ACPI / PMIC: xpower: Add support for the GPI1 regulator to the OpRegion handler
* acpi-misc:
ACPI: fix whitespace in pr_fmt() to align log entries
* acpi-tables:
ACPI: configfs: Unload SSDT on configfs entry removal
* acpica: (53 commits)
ACPICA: Use designated initializers
ACPICA: Update version to 20170531
ACPICA: Update a couple of debug output messages
ACPICA: acpiexec: enhance local signal handler
ACPICA: Simplify output for the ACPI Debug Object
ACPICA: Unix application OSL: Correctly handle control-c (EINTR)
ACPICA: Improvements for debug output only
ACPICA: Disassembler: allow conflicting external declarations to be emitted.
ACPICA: Disassembler: add external op to namespace on first pass
ACPICA: Disassembler: prevent external op's from opening a new scope
ACPICA: Changed Gbl_disasm_flag to acpi_gbl_disasm_flag
ACPICA: Changing External to a named object
ACPICA: Update two error messages to emit control method name
ACPICA: Fix for Device/Thermal objects with ObjectType and DerefOf
ACPICA: Comment update: spelling/format. No functional change
ACPICA: Update comments, no functional change
ACPICA: Split resource descriptor decode strings to a new file
ACPICA: Remove extraneous status check
ACPICA: Export the public mutex interfaces
ACPICA: Disassembler: Abort on an invalid/unknown AML opcode
...
* acpi-pm:
PM / core: Drop run_wake flag from struct dev_pm_info
PCI / PM: Simplify device wakeup settings code
PCI / PM: Drop pme_interrupt flag from struct pci_dev
ACPI / PM: Consolidate device wakeup settings code
ACPI / PM: Drop run_wake from struct acpi_device_wakeup_flags
ACPI / sleep: EC-based wakeup from suspend-to-idle on recent systems
platform: x86: intel-hid: Wake up the system from suspend-to-idle
platform: x86: intel-vbtn: Wake up the system from suspend-to-idle
ACPI / PM: Ignore spurious SCI wakeups from suspend-to-idle
platform/x86: Add driver for ACPI INT0002 Virtual GPIO device
PCI / PM: Restore PME Enable if skipping wakeup setup
PM / sleep: Print timing information if debug is enabled
ACPI / PM: Clean up device wakeup enable/disable code
ACPI / PM: Change log level of wakeup-related message
USB / PCI / PM: Allow the PCI core to do the resume cleanup
ACPI / PM: Run wakeup notify handlers synchronously
Conflicts:
drivers/base/power/main.c
ACPI 6.2 defines in section 9.20.7.2 that the OSPM may call a Start
ARS with Flags Bit [1] set upon receiving the 0x81 notification.
Upon receiving the notification, the OSPM may decide to issue
a Start ARS with Flags Bit [1] set to prepare for the retrieval
of existing records and issue the Query ARS Status function to
retrieve the records.
Add support to call a Start ARS from acpi_nfit_uc_error_notify()
with ND_ARS_RETURN_PREV_DATA set when HW_ERROR_SCRUB_ON is not set.
Link: http://www.uefi.org/sites/default/files/resources/ACPI_6_2.pdf
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Linda Knippers <linda.knippers@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Display bus_dsm_mask in sysfs as /sys/bus/nd/devices/ndbusX/nfit/dsm_mask.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add a bus level dsm_mask to nvdimm_bus_descriptor to allow the passthru
calling mechanism to specify a different mask from the cmd_mask.
Populate bus_dsm_mask and use it to filter dsm calls that user can
make through the pass thru interface.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
[djbw: use command number constants instead of a magic mask value]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Set ND_CMD_CALL in the cmd_mask to enable calling root
functions via the pass thru mechanism.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
File size before:
text data bss dec hex filename
20792 1580 994 23366 5b46 drivers/acpi/nfit/core.o
File size After adding 'const':
text data bss dec hex filename
20968 1388 994 23350 5b36 drivers/acpi/nfit/core.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
ASUS GL720VMK is also affected by the EC GPE preference issue.
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some Asus laptops (verified on X550VXK/FX502VD/FX502VE) get no
interrupts when pressing media keys thus the corresponding functions
are not invoked. It's due to the _GPE defines in DSDT for EC returns
differnt value compared to the GPE Number in ECDT. Confirmed with Asus
that the vale in ECDT is the correct one. This commit uses DMI quirks
to prevent calling _GPE when doing ec_parse_device() and keep the ECDT
GPE number setting for the EC device.
With previous commit, it is ensured that if there is an ECDT, it can
always be kept as boot_ec, this patch thus can implement a quirk on
top of the determined ECDT boot_ec.
Link: https://phabricator.endlessm.com/T16033
Link: https://phabricator.endlessm.com/T16722
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195651
Tested-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We prepared _INI/_STA methods for \_SB, \_SB.PCI0, \_SB.LID0 and
\_SB.EC, _HID(PNP0C09)/_CRS/_GPE for \_SB.EC to poke Windows behavior
with qemu, we got the following execution sequence:
\_SB._INI
\_SB.PCI0._STA
\_SB.LID0._STA
\_SB.EC._STA
\_SB.PCI0._INI
\_SB.LID0._INI
\_SB.EC._INI
There is no extra DSDT EC device enumeration process occurring before
the main ACPI device enumeration process. That means acpi_ec_dsdt_probe()
is not Windows-compatible.
Tracking back, it was added by the following commit:
Commit: c5279dee26
Subject: ACPI: EC: Add some basic check for ECDT data
but that commit was misguided.
Why we shouldn't enumerate DSDT EC before the main ACPI device
enumeration?
The only way to know if the DSDT EC is valid would be to evaluate its
_STA control method, but it's not safe to evaluate this control method
that early and out of the ACPI enumeration process, because _STA may
refer to entities (such as resources or ACPI device objects) that may
not have been initialized before OSPM starts to enumerate them via
the main ACPI device enumeration.
But after we had reverted back to the expected behavior, a regression
was reported. On that platform, there is no ECDT, but the platform
control methods access EC operation region earlier than Linux expects
causing some ACPI method execution errors. For this reason, we just
go back to old behavior to still probe DSDT EC as the boot EC.
However, that turns out to lead to yet another functional breakage
and in order to work around all of the problems, we skip boot stage
DSDT probe when the ECDT exists so that a later quirk can always use
correct ECDT GPE setting.
Link: http://bugzilla.kernel.org/show_bug.cgi?id=11880
Link: http://bugzilla.kernel.org/show_bug.cgi?id=119261
Link: http://bugzilla.kernel.org/show_bug.cgi?id=195651
Tested-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[ rjw: Changelog & comments massage ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It's reported that some buggy BIOS tables can contain 2 DSDT ECs, one of
them is invalid but acpi_ec_dsdt_probe() fails to pick the valid one.
This patch simply enhances sanity checks in ec_parse_device() as a
workaround to skip probing wrong namespace ECs.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195651
Tested-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Dell Precision 7510 has a broken acpi-video implementation.
The backlight control bits work, but when the brightness is changed via
the acpi-video interface the backlight flickers annoyingly before settling
at the new brightness, switching to using the native interface fixes the
flickering so add a quirk for this (the vendor interface can not change the
brightness at all).
Signed-off-by: Shih-Yuan Lee (FourDollars) <sylee@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_ec_cmd_string() currently is only enabled for "DEBUG" macro, but users
trend to use CONFIG_DYNAMIC_DEBUG and enable ec.c pr_debug() print-outs by
"dyndbg='file ec.c +p'". In this use case, all command names are turned
into UNDEF and the log is confusing. This affects bugzilla triage work.
This patch fixes this issue by enabling acpi_ec_cmd_string() for
CONFIG_DYNAMIC_DEBUG.
Tested-by: Wang Wendy <wendy.wang@intel.com>
Tested-by: Feng Chenzhou <chenzhoux.feng@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The EC event IRQ (SCI_EVT) can only be handled by submitting QR_EC. As the
EC driver handles SCI_EVT in a workqueue, after SCI_EVT is flagged and
before QR_EC is submitted, there is a period risking IRQ storming. EC IRQ
must be masked for this period but linux EC driver never does so.
No end user notices the IRQ storming and no developer fixes this known
issue because:
1. The EC IRQ is always edge triggered GPE, and
2. The kernel can execute no-op EC IRQ handler very fast.
For edge-triggered EC GPE platforms, it is only reported of post-resume EC
event lost issues, there won't be an IRQ storming. For level triggered EC
GPE platforms, fortunately the kernel is always fast enough to execute such
a no-op EC IRQ handler so that the IRQ handler won't be accumulated to
starve the task contexts, causing a real IRQ storming.
But the IRQ storming actually can still happen when:
1. The EC IRQ performs like level triggered GPE, and
2. The kernel EC debugging log is turned on but the console is slow enough.
There are more and more platforms using EC GPE as wake GPE where the EC GPE
is likely designed as level triggered. Then when EC debugging log is
enabled, the EC IRQ handler is no longer a no-op but dumps IRQ status to
the consoles. If the consoles are slow enough, the EC IRQs can arrive much
faster than executing the handler. Finally the accumulated EC event IRQ
handlers starve the task contexts, causing the IRQ storming to occur, and
the kernel hangs can be observed during boot/resume.
This patch fixes this issue by masking EC IRQ for this period:
1. Begins when there is an SCI_EVT IRQ pending, and
2. Ends when there is a QR_EC completed (SCI_EVT acknowledged).
Tested-by: Wang Wendy <wendy.wang@intel.com>
Tested-by: Feng Chenzhou <chenzhoux.feng@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The run_wake flag in struct dev_pm_info is used to indicate whether
or not the device is capable of generating remote wakeup signals at
run time (or in the system working state), but the distinction
between runtime remote wakeup and system wakeup signaling has always
been rather artificial. The only practical reason for it to exist
at the core level was that ACPI and PCI treated those two cases
differently, but that's not the case any more after recent changes.
For this reason, get rid of the run_wake flag and, when applicable,
use device_set_wakeup_capable() and device_can_wakeup() instead of
device_set_run_wake() and device_run_wake(), respectively.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The pme_interrupt flag in struct pci_dev is set when PMEs generated
by the device are going to be signaled via root port PME interrupts.
Ironically enough, that information is only used by the code setting
up device wakeup through ACPI which returns as soon as it sees the
pme_interrupt flag set while setting up "remote runtime wakeup".
That is questionable, however, because in theory there may be PCIe
devices using out-of-band PME signaling under root ports handled
by the native PME code or devices requiring wakeup power setup to be
carried out by AML. For such devices, ACPI wakeup should be invoked
regardless of whether or not native PME signaling is used in general.
For this reason, drop the pme_interrupt flag and rework the code
using it which then allows the ACPI-based device wakeup handling
in PCI to be consolidated to use one code path for both "runtime
remote wakeup" and system wakeup (from sleep states).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Currently, there are two separate ways of handling device wakeup
settings in the ACPI core, depending on whether this is runtime
wakeup or system wakeup (from sleep states). However, after the
previous commit eliminating the run_wake ACPI device wakeup flag,
there is no difference between the two any more at the ACPI level,
so they can be combined.
For this reason, introduce acpi_pm_set_device_wakeup() to replace both
acpi_pm_device_run_wake() and acpi_pm_device_sleep_wake() and make it
check the ACPI device object's wakeup.valid flag to determine whether
or not the device can be set up to generate wakeup signals.
Also notice that zpodd_enable/disable_run_wake() only call
device_set_run_wake() because acpi_pm_device_run_wake() called
device_run_wake(), which is not done by acpi_pm_set_device_wakeup(),
so drop the now redundant device_set_run_wake() calls from there.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The run_wake flag in struct acpi_device_wakeup_flags stores the
information on whether or not the device can generate wakeup
signals at run time, but in ACPI that really is equivalent to
being able to generate wakeup signals at all.
In fact, run_wake will always be set after successful executeion of
acpi_setup_gpe_for_wake(), but if that fails, the device will not be
able to use a wakeup GPE at all, so it won't be able to wake up the
systems from sleep states too. Hence, run_wake actually means that
the device is capable of triggering wakeup and so it is equivalent
to the valid flag.
For this reason, drop run_wake from struct acpi_device_wakeup_flags
and make sure that the valid flag is only set if
acpi_setup_gpe_for_wake() has been successful.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Allow volatile nfit ranges to participate in all the same infrastructure
provided for persistent memory regions. A resulting resulting namespace
device will still be called "pmem", but the parent region type will be
"nd_volatile". This is in preparation for disabling the dax ->flush()
operation in the pmem driver when it is hosted on a volatile range.
Cc: Jan Kara <jack@suse.cz>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that all callers of the pmem api have been converted to dax helpers that
call back to the pmem driver, we can remove include/linux/pmem.h and
asm/pmem.h.
Cc: <x86@kernel.org>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Oliver O'Halloran <oohall@gmail.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The struct layout randomization plugin detects and randomizes any structs
that contain only function pointers. Once layout is randomized, all
initialization must be designated or the compiler will misalign the
assignments. This switches all the ACPICA function pointer struct to
use designated initializers, using the proposed upstream ACPICA macro:
https://github.com/acpica/acpica/pull/248/
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 809c1766598c7f3decaeeba2c6ed603c538d0270
Cleanup output.
Link: https://github.com/acpica/acpica/commit/809c1766
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit ffef4ae9a1b6032ebadeab2c2b806f0e585f0006
Add support for SIGSEGV
Improve/cleanup SIGINT handling
Link: https://github.com/acpica/acpica/commit/ffef4ae9
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit ea08cda9859d9f758f4832400b2d559847c2d52a
Cleanup the output, change [Acpi Debug] to Acpi Debug:
Link: https://github.com/acpica/acpica/commit/ea08cda9
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit c3f798b7b0e4f2403d3ce0cc1107ab0932efe1e3
Changes to debug print and debug function tracing.
Link: https://github.com/acpica/acpica/commit/c3f798b7
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 0ed9f2e2ccc112439eaa355b5952a05d6fdb7814
An external declaration is a conflicting declaration when a name has
been declared as an external and a named object within the same file.
Link: https://github.com/acpica/acpica/commit/0ed9f2e2
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 117be4819588df3b7146f6f01723639b1d61e775
By doing so, external control method resolutions can be resolved like
normal control methods. This eliminates the need to reparse the aml
all over again for external control methods that were encoded within
the aml with the 0x15 bytecode.
Link: https://github.com/acpica/acpica/commit/117be481
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit c512c2bfcce65b8e8f37d549ac2fa4a1e0182e46
Since Externals could be of ACPI_TYPE_METHOD, there is a possibility
that the acpi_ns_lookup may cause a new scope to be opened. Therefore,
disable opening the scope for all acpi_ns_lookup invocations that deal
with externals.
Link: https://github.com/acpica/acpica/commit/c512c2bf
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 0e0a87111f280c197661689979b2c48443b0326c
This is a name change as well as a change in the scope of this flag.
This is done so that it can be referenced in the dispatcher.
Link: https://github.com/acpica/acpica/commit/0e0a8711
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 0d5dd42fd7d5129835b6d92250378a962eb73cb3
This is done so that the aml parser will build the parse tree of
External Op as a named object. This is done to streamline creation
of external op parse nodes and facilitate namespace resolution of
externals.
Link: https://github.com/acpica/acpica/commit/0d5dd42f
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 73f7fab1376d5dbfda24cf51c1bb04df0d31b48e
Intention is to improve debugging by clarifying which method
has caused the error, in acpi_evaluate_object_typed.
Link: https://github.com/acpica/acpica/commit/73f7fab1
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 89565151aa4db7b546d4935b187bf2c4a86885ee
These types must be special cased because the namespace node
does not contain a subobject as do all other types.
Link: https://github.com/acpica/acpica/commit/89565151
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 45eb6384fb47f4fdc5759f63c47a9b6799924972
Link: https://github.com/acpica/acpica/commit/45eb6384
Signed-off-by: Cao Jin <caoj.fnst@cn.fujitsu.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 00906ae0aff4c6b76abc232ef99700e7d7c0e325
There are enough of these strings to justify a separate file.
Also, these strings are only used for the disassembler and
the debugger. Thus, this change improves ACPICA modularity.
Link: https://github.com/acpica/acpica/commit/00906ae0
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cavium ThunderX2 SMMU doesn't support MSI and also doesn't have unique irq
lines for gerror, eventq and cmdq-sync.
New named irq "combined" is set as a errata workaround, which allows to
share the irq line by register single irq handler for all the interrupts.
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Geetha sowjanya <gakula@caviumnetworks.com>
[will: reworked irq equality checking and added SPI check]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cavium ThunderX2 implementation doesn't support second page in SMMU
register space. Hence, resource size is set as 64k for this model.
Signed-off-by: Linu Cherian <linu.cherian@cavium.com>
Signed-off-by: Geetha Sowjanya <geethasowjanya.akula@cavium.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The model number is already defined in acpica and we are actually
waiting for the acpi maintainers to include it:
https://github.com/acpica/acpica/commit/d00a4eb86e64
Adding those temporary definitions until the change makes it into
include/acpi/actbl2.h. Once that is done this patch can be reverted.
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Some recent Dell laptops, including the XPS13 model numbers 9360 and
9365, cannot be woken up from suspend-to-idle by pressing the power
button which is unexpected and makes that feature less usable on
those systems. Moreover, on the 9365 ACPI S3 (suspend-to-RAM) is
not expected to be used at all (the OS these systems ship with never
exercises the ACPI S3 path in the firmware) and suspend-to-idle is
the only viable system suspend mechanism there.
The reason why the power button wakeup from suspend-to-idle doesn't
work on those systems is because their power button events are
signaled by the EC (Embedded Controller), whose GPE (General Purpose
Event) line is disabled during suspend-to-idle transitions in Linux.
That is done on purpose, because in general the EC tends to be noisy
for various reasons (battery and thermal updates and similar, for
example) and all events signaled by it would kick the CPUs out of
deep idle states while in suspend-to-idle, which effectively might
defeat its purpose.
Of course, on the Dell systems in question the EC GPE must be enabled
during suspend-to-idle transitions for the button press events to
be signaled while suspended at all, but fortunately there is a way
out of this puzzle.
First of all, those systems have the ACPI_FADT_LOW_POWER_S0 flag set
in their ACPI tables, which means that the OS is expected to prefer
the "low power S0 idle" system state over ACPI S3 on them. That
causes the most recent versions of other OSes to simply ignore ACPI
S3 on those systems, so it is reasonable to expect that it should not
be necessary to block GPEs during suspend-to-idle on them.
Second, in addition to that, the systems in question provide a special
firmware interface that can be used to indicate to the platform that
the OS is transitioning into a system-wide low-power state in which
certain types of activity are not desirable or that it is leaving
such a state and that (in principle) should allow the platform to
adjust its operation mode accordingly.
That interface is a special _DSM object under a System Power
Management Controller device (PNP0D80). The expected way to use it
is to invoke function 0 from it on system initialization, functions
3 and 5 during suspend transitions and functions 4 and 6 during
resume transitions (to reverse the actions carried out by the
former). In particular, function 5 from the "Low-Power S0" device
_DSM is expected to cause the platform to put itself into a low-power
operation mode which should include making the EC less verbose (so to
speak). Next, on resume, function 6 switches the platform back to
the "working-state" operation mode.
In accordance with the above, modify the ACPI suspend-to-idle code
to look for the "Low-Power S0" _DSM interface on platforms with the
ACPI_FADT_LOW_POWER_S0 flag set in the ACPI tables. If it's there,
use it during suspend-to-idle transitions as prescribed and avoid
changing the GPE configuration in that case. [That should reflect
what the most recent versions of other OSes do.]
Also modify the ACPI EC driver to make it handle events during
suspend-to-idle in the usual way if the "Low-Power S0" _DSM interface
is going to be used to make the power button events work while
suspended on the Dell machines mentioned above
Link: http://www.uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Check for pending errors when probing GHES entries. It is possible
that a fatal error is already pending at this point, so we should
handle it as soon as the driver is probed. This also avoids a
potential issue if there was an interrupt that was already
cleared for an error since the GHES driver wasn't present.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently external aborts are unsupported by the guest abort
handling. Add handling for SEAs so that the host kernel reports
SEAs which occur in the guest kernel.
When an SEA occurs in the guest kernel, the guest exits and is
routed to kvm_handle_guest_abort(). Prior to this patch, a print
message of an unsupported FSC would be printed and nothing else
would happen. With this patch, the code gets routed to the APEI
handling of SEAs in the host kernel to report the SEA information.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <cdall@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently there are trace events for the various RAS
errors with the exception of ARM processor type errors.
Add a new trace event for such errors so that the user
will know when they occur. These trace events are
consistent with the ARM processor error section type
defined in UEFI 2.6 spec section N.2.4.4.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Xie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The UEFI spec includes non-standard section type support in the
Common Platform Error Record. This is defined in section N.2.3 of
UEFI version 2.5.
Currently if the CPER section's type (UUID) does not match any
section type that the kernel knows how to parse, a trace event is
not generated.
Generate a trace event which contains the raw error data for
non-standard section type error records.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
CC: Jonathan (Zhixiong) Zhang <zjzhang@codeaurora.org>
Tested-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Even if an error status block's severity is fatal, the kernel does not
honor the severity level and panic.
With the firmware first model, the platform could inform the OS about a
fatal hardware error through the non-NMI GHES notification type. The OS
should panic when a hardware error record is received with this
severity.
Call panic() after CPER data in error status block is printed if
severity is fatal, before each error section is handled.
Signed-off-by: Jonathan (Zhixiong) Zhang <zjzhang@codeaurora.org>
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
ARM APEI extension proposal added SEA (Synchronous External Abort)
notification type for ARMv8.
Add a new GHES error source handling function for SEA. If an error
source's notification type is SEA, then this function can be registered
into the SEA exception handler. That way GHES will parse and report
SEA exceptions when they occur.
An SEA can interrupt code that had interrupts masked and is treated as
an NMI. To aid this the page of address space for mapping APEI buffers
while in_nmi() is always reserved, and ghes_ioremap_pfn_nmi() is
changed to use the helper methods to find the prot_t to map with in
the same way as ghes_ioremap_pfn_irq().
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
CC: Jonathan (Zhixiong) Zhang <zjzhang@codeaurora.org>
Reviewed-by: James Morse <james.morse@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The ACPI 6.1 spec adds a new revision of the generic error data
entry structure. Add support to handle the new structure as well
as properly verify and iterate through the generic data entries.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
CC: Jonathan (Zhixiong) Zhang <zjzhang@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
A RAS (Reliability, Availability, Serviceability) controller
may be a separate processor running in parallel with OS
execution, and may generate error records for consumption by
the OS. If the RAS controller produces multiple error records,
then they may be overwritten before the OS has consumed them.
The Generic Hardware Error Source (GHES) v2 structure
introduces the capability for the OS to acknowledge the
consumption of the error record generated by the RAS
controller. A RAS controller supporting GHESv2 shall wait for
the acknowledgment before writing a new error record, thus
eliminating the race condition.
Add support for parsing of GHESv2 sub-tables as well.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
CC: Jonathan (Zhixiong) Zhang <zjzhang@codeaurora.org>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add fwnode_device_is_available() to tell whether the device corresponding
to a certain fwnode_handle is available for use.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Move firmware specific implementations of the fwnode graph operations to
firmware specific locations.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The device and fwnode property API supports Devicetree, ACPI and pset
properties. The implementation of this functionality for each firmware
type was embedded in the fwnode property core. Move it out to firmware
type specific locations, making it easier to maintain.
Depends-on: ("of: Move OF property and graph API from base.c to property.c")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This will be needed in constifying the fwnode API.
The side effects the function had have been moved to the callers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Call directly into acpica to load a table to obtain its index on return.
We choose the direct call of acpica internal functions to avoid having
to modify its API which is used outside of Linux as well.
Use that index to unload the table again when the corresponding
directory in configfs gets removed. This allows to change SSDTs without
rebooting the system. It also allows to destroy devices again that a
dynamically loaded SSDT created.
This is widely similar to the DT overlay behavior.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some Bay Trail devices use a GPI1 regulator field (address 0x4c) in
their 0x8d power OpRegion, add support for this.
This fixes AE_BAD_PARAMETER errors getting thrown on these devices and
fixes these errors causing these devices to not suspend.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit f406270bf7 ("ACPI / scan: Set the visited flag for all
enumerated devices") caused that two group of special SPI or I2C
devices do not enumerate. SPI and I2C devices are expected to be
enumerated by the SPI and I2C subsystems but change caused that
acpi_bus_attach() marks those devices with acpi_device_set_enumerated().
First group of devices are matched using Device Tree compatible property
with special _HID "PRP0001". Those devices have matched scan handler,
acpi_scan_attach_handler() retuns 1 and acpi_bus_attach() marks them
with acpi_device_set_enumerated().
Second group of devices without valid _HID such as "LNXVIDEO" have
device->pnp.type.platform_id set to zero and change again marks them
with acpi_device_set_enumerated().
Fix this by flagging the SPI and I2C devices during struct acpi_device
object initialization time and let the code in acpi_bus_attach() to go
through the device_attach() and acpi_default_enumeration() path for all
SPI and I2C devices.
Fixes: f406270bf7 (ACPI / scan: Set the visited flag for all enumerated devices)
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: 4.11+ <stable@vger.kernel.org> # 4.11+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Conflicts:
kernel/sched/Makefile
Pick up the waitqueue related renames - it didn't get much feedback,
so it appears to be uncontroversial. Famous last words? ;-)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
ACPI 6.2 defines a new ACPI notification value to NVDIMM Root Device
in Table 5-169.
0x81 Unconsumed Uncorrectable Memory Error Detected
Used to pro-actively notify OSPM of uncorrectable memory errors
detected (for example a memory scrubbing engine that continuously
scans the NVDIMMs memory). This is an optional notification. Only
locations that were mapped in to SPA by the platform will generate
a notification.
Add support of this notification value by initiating an ARS scan. This
will find new error locations and add their badblocks information.
Link: http://www.uefi.org/sites/default/files/resources/ACPI_6_2.pdf
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Linda Knippers <linda.knippers@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Starting with the v1.2 definition of namespace labels, the isetcookie
field is populated and validated for blk-aperture namespaces. This adds
some safety against inadvertent copying of namespace labels from one
DIMM-device to another.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The type_guid refers to the "Address Range Type GUID" for the region
backing a namespace as defined the ACPI NFIT (NVDIMM Firmware Interface
Table). This 'type' identifier specifies an access mechanism for the
given namespace. This capability replaces the confusing usage of the
'NSLABEL_FLAG_LOCAL' flag to indicate a block-aperture-mode namespace.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The interleave-set-cookie algorithm is extended to incorporate all the
same components that are used to generate an nvdimm unique-id. For
backwards compatibility we still maintain the old v1.1 definition.
Reported-by: Nicholas Moulin <nicholas.w.moulin@intel.com>
Reported-by: Kaushik Kanetkar <kaushik.a.kanetkar@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Commit 316ca8804e ("ACPI/IORT: Remove linker section for IORT entries
probing") removed the linker section for IORT entries probing.
Since those IORT entries were the only iort_node_match() interface
users, the iort_node_match() became obsolete and can then be removed.
Remove the ACPI IORT iort_node_match() interface from the kernel.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The ACPI SCI (System Control Interrupt) is set up as a wakeup IRQ
during suspend-to-idle transitions and, consequently, any events
signaled through it wake up the system from that state. However,
on some systems some of the events signaled via the ACPI SCI while
suspended to idle should not cause the system to wake up. In fact,
quite often they should just be discarded.
Arguably, systems should not resume entirely on such events, but in
order to decide which events really should cause the system to resume
and which are spurious, it is necessary to resume up to the point
when ACPI SCIs are actually handled and processed, which is after
executing dpm_resume_noirq() in the system resume path.
For this reasons, add a loop around freeze_enter() in which the
platforms can process events signaled via multiplexed IRQ lines
like the ACPI SCI and add suspend-to-idle hooks that can be
used for this purpose to struct platform_freeze_ops.
In the ACPI case, the ->wake hook is used for checking if the SCI
has triggered while suspended and deferring the interrupt-induced
system wakeup until the events signaled through it are actually
processed sufficiently to decide whether or not the system should
resume. In turn, the ->sync hook allows all of the relevant event
queues to be flushed so as to prevent events from being missed due
to race conditions.
In addition to that, some ACPI code processing wakeup events needs
to be modified to use the "hard" version of wakeup triggers, so that
it will cause a system resume to happen on device-induced wakeup
events even if the "soft" mechanism to prevent the system from
suspending is not enabled. However, to preserve the existing
behavior with respect to suspend-to-RAM, this only is done in
the suspend-to-idle case and only if an SCI has occurred while
suspended.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The wakeup.flags.enabled flag in struct acpi_device is not used
consistently, as there is no reason why it should only apply
to the enabling/disabling of the wakeup GPE, so put the invocation
of acpi_enable_wakeup_device_power() under it too.
Moreover, it is not necessary to call
acpi_enable_wakeup_devices() and acpi_disable_wakeup_devices() for
suspend-to-idle, so don't do that.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Change the log level of the "System wakeup enabled/disabled by ACPI"
message in acpi_pm_device_sleep_wake() to "debug" to reduce to log
noise level.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The work functions provided by the users of acpi_add_pm_notifier()
should be run synchronously before re-enabling the wakeup GPE in
case they are used to clear the status and/or disable the wakeup
signaling at the source. Otherwise, which is the case currently in
the PCI bus type code, the same wakeup event may be signaled for
multiple times while the execution of the work function in response
to it has already been queued up.
Fortunately, acpi_add_pm_notifier() is only used by PCI and by
ACPI device PM code internally, so the change is relatively
straightforward to make.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
ACPICA commit a83f7212df71d4276d0057fa31bfdc9809660560
Removed an unnecessary status check after call to
ns_build_normalized_path.
Link: https://bugs.acpica.org/show_bug.cgi?id=1378
Link: https://github.com/acpica/acpica/commit/a83f7212
Reported-by: Colin King <colin.king@canonical.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit ff09dcf9eb69fe9318034c60c377436030e7feea
These interfaces are intended to be used by device drivers.
Link: https://github.com/acpica/acpica/commit/ff09dcf9
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit ed0389cb11a61e63c568ac1f67948fc6a7bd1aeb
An invalid opcode indicates something seriously wrong with the
input AML file. The AML parser is immediately confused and lost,
causing the resulting parse tree to be ill-formed. The actual
disassembly can then cause numerous unrelated errors and faults.
This change aborts the disassembly upon discovery of such an
opcode during the AML parse phase.
Link: https://github.com/acpica/acpica/commit/ed0389cb
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit eaa455accf165fee2df26410e271aab162264f6c
UBSAN reports an index out of range use in dsutils.c.
acpi_db_display_argument_object(
walk_state->operands[walk_state->num_operands - 1],
^^^^^^^^^^^^^^^^^^^^^^^^^^^^
walk_state);
This call was simply wrong, generated redundant debugger messages, and
resulted in a -1 index into the operand stack. Linux kernel bug #120351
(link #1) and #194845 (link #2).
Originally fixed by Navin P.S. (link #1, comment 8), refined by Lv Zheng
(link #3).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=120351 [#1]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194845 [#2]
Link: https://github.com/acpica/acpica/pull/245 [#3]
Link: https://github.com/acpica/acpica/commit/eaa455ac
Reported-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de>
Reported-by: Ronald Warsow <rwarsow@gmx.de>
Original-by: Navin P.S. <navinp1912@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 0d792c25d3bcaa857920ec009b732ec7c8942cfa
Clarify some of the error messages when a method failure happens.
Link: https://github.com/acpica/acpica/commit/0d792c25
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 4091360d6526c8d4f1e6bccb6b1c3123bda9ac33
The runtime errors caused when acpica tools are compiled with
-fsanitize=shift imply that these 1s are stored in integers.
This cast insures that 1 is stored in unsigned integers.
Link: https://github.com/acpica/acpica/commit/4091360d
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 7a6b9c0b31cfb1606a6348404fee670b2d18743c
Improve/clarify the problem of a field definition beyond the limit
of the target buffer.
Link: https://github.com/acpica/acpica/commit/7a6b9c0b
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 99bc3beca92c6574ea1d69de42e54f872e6373ce
It is reported that on Linux, RTC driver complains wrong errors on
hardware reduced platform:
[ 4.085420] ACPI Warning: Could not enable fixed event - real_time_clock (4) (20160422/evxface-654)
This patch fixes this by correctly adding runtime reduced hardware check.
Reported by Chandan Tagore, fixed by Lv Zheng.
Link: https://github.com/acpica/acpica/commit/99bc3bec
Tested-by: Chandan Tagore <tagore.chandan@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 51a92f414de7af1f7f7524de3f61daf5413cac9f
Acpiexec gives this warning when resources containing GPIOs are extracted
using Resource command:
**** Data mismatch in descriptor [00] type 8C, Offset 00000000 ****
Mismatch at byte offset 13: is 00, should be 25
**** Data mismatch in descriptor [01] type 8C, Offset 00000025 ****
Mismatch at byte offset 13: is 00, should be 25
This happens because we do not set VendorOffset when doing resource to AML
conversion. Fix this by always setting VendorOffset.
Link: https://github.com/acpica/acpica/commit/51a92f41
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 7cb6e66982178bbc96a6f1f7969da95e9da753fa
An AML opcode type field was overlapped with values used
for the top-level dispatch. Did not cause an actual problem,
but fixed anyway.
Link: https://github.com/acpica/acpica/commit/7cb6e669
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 08b83591c0db751769d61fa889f4f50f575aeffb
PinGroupConfig() is analogous to PinGroupFunction() but instead of mode
(muxing), it is used to apply specific fine-grained configuration to a
set of referenced pins.
The format of this new resource is:
PinGroupConfig (Shared/Exclusive, PinConfigType, PinConfigValue,
ResourceSource, ResourceSourceIndex, ResourceSourceLabel,
ResourceUsage, DescriptorName, VendorData)
The PinConfigType/PinConfigValue are the same used by PinConfig()
resource.
Here also the combination of ResourceSource and ResourceSourceLabel is
used to specify the PinGroup() this resource refers to.
Link: https://github.com/acpica/acpica/commit/08b83591
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit bd9a745749eac7137cd23085e6bdeb322de14ea2
PinGroupFunction() is a new resource introduced with ACPI 6.2. It is
used with PinGroup() to configure specific mode for a set of pins
exposed by a GPIO controller.
The format of the resource is:
PinGroupFunction (Shared/Exclusive, FunctionNumber, ResourceSource,
ResourceSourceIndex, ResourceSourceLabel,
ResourceUsage, DescriptorName, VendorData)
The resource_source and ResourceSourceLabel fields are used to specify
the PinGroup() resource referenced by PinGroupFunction().
Device (GPIO)
{
Name (_CRS, ResourceTemplate () {
PinGroup ("group1") {2, 3}
PinGroup ("group2") {4, 5}
...
})
}
Device (I2C)
{
Name (_CRS, ResourceTemplate () {
PinGroupFunction (Exclusive, 6, "^GPIO", 0, "mygroup2")
})
}
In the above example the PinGroupFunction() references the second
PinGroup() resource (using label "mygroup2" and configures pins 4 and 5
into mode 6.
Link: https://github.com/acpica/acpica/commit/bd9a7457
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 7d928e3174fb19d7dc0066b03c30bea07c001563
ACPI 6.2 introduced a new resource that is used to declare set of pins
belonging to a GPIO controller. This resource is referenced by new
PinGroupFunction() and PinGroupConfig() resources using ResourceSource
and ResourceLabel fields.
The PinGroup() resource looks like this:
PinGroup (ResourceLabel, ResourceUsage, DescriptorName,
VendorData) {Pin List}
This resource should be listed in _CRS under the GPIO/pincontroller
device providing these pins.
Link: https://github.com/acpica/acpica/commit/7d928e31
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit a06fdba686cefccd5dd5b93b52fa0f1e3f984906
ACPI 6.2 introduced a new resource that is used to specify fine-grained
configuration of a pin or set of pins used by a device. The ASL syntax of
this new resource looks like:
PinConfig (Shared/Exclusive, PinConfigType, PinConfigValue,
ResourceSource, ResourceSourceIndex, ResourceUsage,
DescriptorName, Vendordata) {Pin List}
PinConfigType is an integer with following accepted values:
0x00 (Default) - No configuration is applied to the pin
0x01 (Bias Pull-up) - Pin is pulled up using certain size resistor
0x02 (Bias Pull-down) - Pin is pulled down using certain size resistor
0x03 (Bias Default) - Set to default biasing
0x04 (Bias Disable) - All bias settings will be disabled
0x05 (Bias High Impedance) - Configure the pin as hi_z
0x06 (Bias Bus Hold) - Configure the pin in a weak latch state where
it drives the last value on a tristate bus
0x07 (Drive Open Drain) - Configure the pin into open drain state
0x08 (Drive Open Source) - Configure the pin into open source state
0x09 (Drive Push Pull) - Configure the pin into push-pull state
0x0a (Drive Strength) - How much the pin can supply current
0x0b (Slew Rate) - Configure slew rate of the pin
0x0c (Input Debounce) - Enable input debouncer for the pin
0x0d (Input Schmitt Trigger) - Enable schmitt trigger for the pin
0x0e - 0x7f - Reserved
0x80 - 0xff - Vendor defined types
The PinConfigValue depends on the type and is expressed as units
suitable for that type (for example bias uses Ohms).
Link: https://github.com/acpica/acpica/commit/a06fdba6
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 6bbc6357f7061f1243601adde0ea45f7a89274e0
ACPI 6.2 introduced a new resource that is used to describe how certain
pins are muxed for a device. The ASL syntax of this new resource looks
like below:
PinFunction(Shared, PinConfig, FunctionNumber, ResourceSource,
ResourceSourceIndex, ResourceUsage, DescriptorName,
VendorData) {Pin List}
Which is pretty similar to GpioIo()/GpioInt() resources.
Teach ACPICA about this new resource.
Link: https://github.com/acpica/acpica/commit/6bbc6357
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 3c36625deffdfb034378b1793e2ead9c8fdd767e
Changes the resource descriptor parse tree walk to a general
preprocessing walk and calls the Switch conversion code from here.
Move Switch code to new dmswitch.c file. Also improves algorithm to
handle multiple levels of Switch statements and perform legacy
disassembly for older or otherwise non-spec compliant Switch
implementations.
Link: https://github.com/acpica/acpica/commit/3c36625d
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 223a647c72243359231865a64c1be04d208dcdbd
Link: https://github.com/acpica/acpica/commit/223a647c
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 8e425bdd9fa27264c217a3a449eb3c2da3769542
Link: https://github.com/acpica/acpica/commit/8e425bdd
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 89020347ada3f0ff5499a804178d574359e4730f
Link: https://github.com/acpica/acpica/commit/89020347
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit f2f3813fb6b6a6ec1f406f05061c0e9270e86146
Link: https://github.com/acpica/acpica/commit/f2f3813f
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 54eb9be35414847da7e2903c8d410fa806b44fb5
0x0C (Graceful shutdown) is now reverted to reserved.
0x81 takes the place of this value.
Link: https://github.com/acpica/acpica/commit/54eb9be3
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit d37e878292bc9c7835b74e90d1c4c79e96ce6652
New notify value for memory attributes update for ACPI 6.2.
Link: https://github.com/acpica/acpica/commit/d37e8782
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 51e73c1d35dd21cfe39277b3c71decd3268f669c
All instances using a named parseOp's path field has a type
cast from u8* to char*. Changing path's type from u8*
to char* eliminates type casting and retains the previous
behavior.
Link: https://github.com/acpica/acpica/commit/51e73c1d
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Considering this case:
1. A program opens a sysfs table file 65535 times, it can increase
validation_count and first increment cause the table to be mapped:
validation_count = 65535
2. AML execution causes "Load" to be executed on the same
table, this time it cannot increase validation_count, so
validation_count remains:
validation_count = 65535
3. The program closes sysfs table file 65535 times, it can decrease
validation_count and the last decrement cause the table to be
unmapped:
validation_count = 0
4. AML code still accessing the loaded table, kernel crash can be
observed.
To prevent that from happening, add a validation_count threashold.
When it is reached, the validation_count can no longer be
incremented/decremented to invalidate the table descriptor (means
preventing table unmappings)
Note that code added in acpi_tb_put_table() is actually a no-op but
changes the warning message into a "warn once" one. Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[ rjw: Changelog, comments ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Including:
* Another compile-fix for my header cleanup
* A couple of fixes for the recently merged IOMMU probe
deferal code
* Includes fixes for ACPI/IORT code necessary with
IOMMU probe deferal
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6dZB
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v4.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- another compile-fix for my header cleanup
- a couple of fixes for the recently merged IOMMU probe deferal code
- fixes for ACPI/IORT code necessary with IOMMU probe deferal
* tag 'iommu-fixes-v4.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
arm: dma-mapping: Reset the device's dma_ops
ACPI/IORT: Move the check to get iommu_ops from translated fwspec
ARM: dma-mapping: Don't tear down third-party mappings
ACPI/IORT: Ignore all errors except EPROBE_DEFER
iommu/of: Ignore all errors except EPROBE_DEFER
iommu/of: Fix check for returning EPROBE_DEFER
iommu/dma: Fix function declaration
The pmem driver has a need to transfer data with a persistent memory
destination and be able to rely on the fact that the destination writes are not
cached. It is sufficient for the writes to be flushed to a cpu-store-buffer
(non-temporal / "movnt" in x86 terms), as we expect userspace to call fsync()
to ensure data-writes have reached a power-fail-safe zone in the platform. The
fsync() triggers a REQ_FUA or REQ_FLUSH to the pmem driver which will turn
around and fence previous writes with an "sfence".
Implement a __copy_from_user_inatomic_flushcache, memcpy_page_flushcache, and
memcpy_flushcache, that guarantee that the destination buffer is not dirty in
the cpu cache on completion. The new copy_from_iter_flushcache and sub-routines
will be used to replace the "pmem api" (include/linux/pmem.h +
arch/x86/include/asm/pmem.h). The availability of copy_from_iter_flushcache()
and memcpy_flushcache() are gated by the CONFIG_ARCH_HAS_UACCESS_FLUSHCACHE
config symbol, and fallback to copy_from_iter_nocache() and plain memcpy()
otherwise.
This is meant to satisfy the concern from Linus that if a driver wants to do
something beyond the normal nocache semantics it should be something private to
that driver [1], and Al's concern that anything uaccess related belongs with
the rest of the uaccess code [2].
The first consumer of this interface is a new 'copy_from_iter' dax operation so
that pmem can inject cache maintenance operations without imposing this
overhead on other dax-capable drivers.
[1]: https://lists.01.org/pipermail/linux-nvdimm/2017-January/008364.html
[2]: https://lists.01.org/pipermail/linux-nvdimm/2017-April/009942.html
Cc: <x86@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
acpi_evaluate_dsm() and friends take a pointer to a raw buffer of 16
bytes. Instead we convert them to use guid_t type. At the same time we
convert current users.
acpi_str_to_uuid() becomes useless after the conversion and it's safe to
get rid of it.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Revert commit eed4d47efe (ACPI / sleep: Ignore spurious SCI wakeups
from suspend-to-idle) as it turned out to be premature and triggered
a number of different issues on various systems.
That includes, but is not limited to, premature suspend-to-RAM aborts
on Dell XPS 13 (9343) reported by Dominik.
The issue the commit in question attempted to address is real and
will need to be taken care of going forward, but evidently more work
is needed for this purpose.
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit da28e1955d (ACPICA: Disassembler: Enhance resource
descriptor detection) as it is based on an assumption that doesn't
hold all the time and causes problems to happen because of that.
Reported-by: Linda Knippers <linda.knippers@hpe.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are new types and helpers that are supposed to be used in new code.
As a preparation to get rid of legacy types and API functions do
the conversion here.
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There are new types and helpers that are supposed to be used in new code.
As a preparation to get rid of legacy types and API functions do
the conversion here.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There are new types and helpers that are supposed to be used in new code.
As a preparation to get rid of legacy types and API functions do
the conversion here.
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There are new types and helpers that are supposed to be used in new code.
As a preparation to get rid of legacy types and API functions do
the conversion here.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
With IOMMU probe deferral, iort_iommu_configure can be called
multiple times for the same device. Hence we have a check
to see if the device's fwspec is already translated and return
the iommu_ops from that directly. But the check is wrongly
placed in iort_iommu_xlate, which breaks devices with multiple
sids. Move the check to iort_iommu_configure.
Fixes: 5a1bb638d5 ("drivers: acpi: Handle IOMMU lookup failure with deferred probing or error")
Tested-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
While deferring the probe of IOMMU masters, xlate and
add_device callbacks called from iort_iommu_configure
can pass back error values like -ENODEV, which means
the IOMMU cannot be connected with that master for real
reasons. Before the IOMMU probe deferral, all such errors
were ignored. Now all those errors are propagated back,
killing the master's probe for such errors. Instead ignore
all the errors except EPROBE_DEFER, which is the only one
of concern and let the master work without IOMMU, thus
restoring the old behavior. Also make explicit that
acpi_dma_configure handles only -EPROBE_DEFER from
iort_iommu_configure.
Fixes: 5a1bb638d5 ("drivers: acpi: Handle IOMMU lookup failure with deferred probing or error")
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
In the Linux kernel, acpi_get_table() "clones" haven't been fully
balanced by acpi_put_table() invocations. In upstream ACPICA, due to
the design change, there are also unbalanced acpi_get_table_by_index()
invocations requiring special care.
acpi_get_table() reference counting mismatches may occor due to that
and printing error messages related to them is not useful at this
point. The strict balanced validation count check should only be
enabled after confirming that all invocations are safe and aligned
with their designed purposes.
Thus this patch removes the error value returned by acpi_tb_get_table()
in that case along with the accompanying error message to fix the
issue.
Fixes: 174cc7187e (ACPICA: Tables: Back port acpi_get_table_with_size() and early_acpi_os_unmap_memory() from Linux kernel)
Cc: 4.10+ <stable@vger.kernel.org> # 4.10+
Reported-by: Anush Seetharaman <anush.seetharaman@intel.com>
Reported-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit 77e9a4aa9d (ACPI / button: Change default behavior to
lid_init_state=open) which changed the kernel's behavior on laptops
that boot with closed lids and expect the lid switch state to be
reported accurately by the kernel.
If you boot or resume your laptop with the lid closed on a docking
station while using an external monitor connected to it, both internal
and external displays will light on, while only the external should.
There is a design choice in gdm to only provide the greeter on the
internal display when lit on, so users only see a gray area on the
external monitor. Also, the cursor will not show up as it's by
default on the internal display too.
To "fix" that, users have to open the laptop once and close it once
again to sync the state of the switch with the hardware state.
Even if the "method" operation mode implementation can be buggy on
some platforms, the "open" choice is worse. It breaks docking
stations basically and there is no way to have a user-space hwdb to
fix that.
On the contrary, it's rather easy in user-space to have a hwdb
with the problematic platforms. Then, libinput (1.7.0+) can fix
the state of the lid switch for us: you need to set the udev
property LIBINPUT_ATTR_LID_SWITCH_RELIABILITY to 'write_open'.
When libinput detects internal keyboard events, it will overwrite the
state of the switch to open, making it reliable again. Given that
logind only checks the lid switch value after a timeout, we can
assume the user will use the internal keyboard before this timeout
expires.
For example, such a hwdb entry is:
libinput:name:*Lid Switch*:dmi:*svnMicrosoftCorporation:pnSurface3:*
LIBINPUT_ATTR_LID_SWITCH_RELIABILITY=write_open
Link: https://bugzilla.gnome.org/show_bug.cgi?id=782380
Cc: 4.11+ <stable@vger.kernel.org> # 4.11+
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull RAS fixes from Thomas Gleixner:
"Two fixlets for RAS:
- Export memory_error() so the NFIT module can utilize it
- Handle memory errors in NFIT correctly"
* 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
acpi, nfit: Fix the memory error check in nfit_handle_mce()
x86/MCE: Export memory_error()
With the enhanced CPU hotplug lockdep coverage the following lockdep splat
happens:
======================================================
WARNING: possible circular locking dependency detected
4.12.0-rc2+ #84 Tainted: G W
------------------------------------------------------
cpuhp/1/15 is trying to acquire lock:
flush_work+0x39/0x2f0
but task is already holding lock:
cpuhp_thread_fun+0x30/0x160
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (cpuhp_state){+.+.+.}:
lock_acquire+0xb4/0x200
cpuhp_kick_ap_work+0x72/0x330
_cpu_down+0x8b/0x100
do_cpu_down+0x3e/0x60
cpu_down+0x10/0x20
cpu_subsys_offline+0x14/0x20
device_offline+0x88/0xb0
online_store+0x4c/0xa0
dev_attr_store+0x18/0x30
sysfs_kf_write+0x45/0x60
kernfs_fop_write+0x156/0x1e0
__vfs_write+0x37/0x160
vfs_write+0xca/0x1c0
SyS_write+0x58/0xc0
entry_SYSCALL_64_fastpath+0x23/0xc2
-> #1 (cpu_hotplug_lock.rw_sem){++++++}:
lock_acquire+0xb4/0x200
cpus_read_lock+0x3d/0xb0
apply_workqueue_attrs+0x17/0x50
__alloc_workqueue_key+0x1e1/0x530
scsi_host_alloc+0x373/0x480 [scsi_mod]
ata_scsi_add_hosts+0xcb/0x130 [libata]
ata_host_register+0x11a/0x2c0 [libata]
ata_host_activate+0xf0/0x150 [libata]
ahci_host_activate+0x13e/0x170 [libahci]
ahci_init_one+0xa3a/0xd3f [ahci]
local_pci_probe+0x45/0xa0
work_for_cpu_fn+0x14/0x20
process_one_work+0x1f9/0x690
worker_thread+0x200/0x3d0
kthread+0x138/0x170
ret_from_fork+0x31/0x40
-> #0 ((&wfc.work)){+.+.+.}:
__lock_acquire+0x11e1/0x13e0
lock_acquire+0xb4/0x200
flush_work+0x5c/0x2f0
work_on_cpu+0xa1/0xd0
acpi_processor_get_throttling+0x3d/0x50
acpi_processor_reevaluate_tstate+0x2c/0x50
acpi_soft_cpu_online+0x69/0xd0
cpuhp_invoke_callback+0xb4/0x8b0
cpuhp_up_callbacks+0x36/0xc0
cpuhp_thread_fun+0x14e/0x160
smpboot_thread_fn+0x1e8/0x300
kthread+0x138/0x170
ret_from_fork+0x31/0x40
other info that might help us debug this:
Chain exists of:
(&wfc.work) --> cpu_hotplug_lock.rw_sem --> cpuhp_state
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(cpuhp_state);
lock(cpu_hotplug_lock.rw_sem);
lock(cpuhp_state);
lock((&wfc.work));
*** DEADLOCK ***
1 lock held by cpuhp/1/15:
cpuhp_thread_fun+0x30/0x160
stack backtrace:
CPU: 1 PID: 15 Comm: cpuhp/1 Tainted: G W 4.12.0-rc2+ #84
Hardware name: Supermicro SYS-4048B-TR4FT/X10QBi, BIOS 1.1a 07/29/2015
Call Trace:
dump_stack+0x85/0xc4
print_circular_bug+0x209/0x217
__lock_acquire+0x11e1/0x13e0
lock_acquire+0xb4/0x200
? lock_acquire+0xb4/0x200
? flush_work+0x39/0x2f0
? acpi_processor_start+0x50/0x50
flush_work+0x5c/0x2f0
? flush_work+0x39/0x2f0
? acpi_processor_start+0x50/0x50
? mark_held_locks+0x6d/0x90
? queue_work_on+0x56/0x90
? trace_hardirqs_on_caller+0x154/0x1c0
? trace_hardirqs_on+0xd/0x10
? acpi_processor_start+0x50/0x50
work_on_cpu+0xa1/0xd0
? find_worker_executing_work+0x50/0x50
? acpi_processor_power_exit+0x70/0x70
acpi_processor_get_throttling+0x3d/0x50
acpi_processor_reevaluate_tstate+0x2c/0x50
acpi_soft_cpu_online+0x69/0xd0
cpuhp_invoke_callback+0xb4/0x8b0
? lock_acquire+0xb4/0x200
? padata_replace+0x120/0x120
cpuhp_up_callbacks+0x36/0xc0
cpuhp_thread_fun+0x14e/0x160
smpboot_thread_fn+0x1e8/0x300
kthread+0x138/0x170
? sort_range+0x30/0x30
? kthread_create_on_node+0x70/0x70
ret_from_fork+0x31/0x40
The problem is that the work is scheduled on the current CPU from the
hotplug thread associated with that CPU.
It's not required to invoke these functions via the workqueue because the
hotplug thread runs on the target CPU already.
Check whether current is a per cpu thread pinned on the target CPU and
invoke the function directly to avoid the workqueue.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-acpi@vger.kernel.org
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/20170524081549.620489733@linutronix.de
Converting the hotplug locking, i.e. get_online_cpus(), to a percpu rwsem
unearthed a circular lock dependency which was hidden from lockdep due to
the lockdep annotation of get_online_cpus() which prevents lockdep from
creating full dependency chains.
CPU0 CPU1
---- ----
lock((&wfc.work));
lock(cpu_hotplug_lock.rw_sem);
lock((&wfc.work));
lock(cpu_hotplug_lock.rw_sem);
This dependency is established via acpi_processor_start() which calls into
the work queue code. And the work queue code establishes the reverse
dependency.
This is not a problem of get_online_cpus() recursion, it's a possible
deadlock undetected by lockdep so far.
The cure is to use cpu_hotplug_disable() instead of get_online_cpus() to
protect the probing from acpi_processor_start().
There is a side effect to this: cpu_hotplug_disable() makes a concurrent
cpu hotplug attempt via the sysfs interfaces fail with -EBUSY, but that
probing usually happens during the boot process where no interaction is
possible. Any later invocations are infrequent enough and concurrent
hotplug attempts are so unlikely that the danger of user space visible
regressions is very close to zero. Anyway, thats preferrable over a real
deadlock.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-acpi@vger.kernel.org
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/20170524081548.851588594@linutronix.de
To enable smp_processor_id() and might_sleep() debug checks earlier, it's
required to add system states between SYSTEM_BOOTING and SYSTEM_RUNNING.
Make the decision whether a pci root is hotplugged depend on SYSTEM_RUNNING
instead of !SYSTEM_BOOTING. It makes no sense to cover states greater than
SYSTEM_RUNNING as there are not hotplug events on reboot and poweroff.
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/20170516184735.446455652@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
System Controller Interrupts are received by ACPI's error device, which
in turn notifies the GHES code. The same is true of APEI's GSIV and
GPIO notification types. Add support for GSIV and GPIO sharing the SCI
register/unregister/notifier code. Rename the list and notifier to show
this is no longer just SCI, but anything from the Hardware Error Device.
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
[ Rewrite commit log. ]
Signed-off-by: James Morse <james.morse@arm.com>
[ Some small cleanups ontop. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Tyler Baicar <tbaicar@codeaurora.org>
Reviewed-by: James Morse <james.morse@arm.com>
Link: http://lkml.kernel.org/r/86258A5CC0A3704780874CF6004BA8A62E695201@FRAEML521-MBX.china.huawei.com
Cc: "Guohanjun (Hanjun Guo)" <guohanjun@huawei.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: "Zhengqiang (turing)" <zhengqiang10@huawei.com>
Cc: "fu.wei@linaro.org" <fu.wei@linaro.org>
Cc: "xuwei (O)" <xuwei5@hisilicon.com>
Cc: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Cc: Geliang Tang <geliangtang@gmail.com>
Cc: John Garry <john.garry@huawei.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: linux-acpi@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The check for an MCE being a memory error in the NFIT mce handler was
bogus. Use the new mce_is_memory_error() helper to detect the error
properly.
Reported-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170519093915.15413-3-bp@alien8.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This reverts commit ecb10b694b.
The only expected ACPI control method lid device's usage model is
1. Listen to the lid notification,
2. Evaluate _LID after being notified by BIOS,
3. Suspend the system (if users configure to do so) after seeing "close".
It's not ensured that BIOS will notify OS after boot/resume, and
it's not ensured that BIOS will always generate "open" event upon
opening the lid.
But there are 2 wrong usage models:
1. When the lid device is responsible for suspend/resume the system,
userspace requires to see "open" event to be paired with "close" after
the system is resumed, or it will suspend the system again.
2. When an external monitor connects to the laptop attached docks,
userspace requires to see "close" event after the system is resumed so
that it can determine whether the internal display should remain dark
and the external display should be lit on.
After we made default kernel behavior to be suitable for usage model 1,
users of usage model 2 start to report regressions for such behavior
change.
Reversion of button.lid_init_state=method doesn't actually reverts to old
default behavior as doing so can enter a regression loop, but facilitates
users to work the reported regressions around with
button.lid_init_state=method.
Fixes: ecb10b694b (ACPI / button: Remove lid_init_state=method mode)
Cc: 4.11+ <stable@vger.kernel.org> # 4.11+
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195455
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1430259
Tested-by: Steffen Weber <steffen.weber@gmail.com>
Tested-by: Julian Wiedmann <julian.wiedmann@jwi.name>
Reported-by: Joachim Frieben <jfrieben@hotmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Update the ACPICA code in the kernel to upstream revision
20170303 which includes:
* Minor fixes and improvements in the core code (Bob Moore,
Seunghun Han).
* Debugger fixes (Colin Ian King, Lv Zheng).
* Compiler/disassembler improvements (Bob Moore, David Box,
Lv Zheng).
* Build-related update (Lv Zheng).
- Add new device IDs and platform-related information to the
ACPI drivers for Intel (LPSS) and AMD (APD) SoCs (Hanjun Guo,
Hans de Goede).
- Make it possible to quirk ACPI-enumerated devices as "always
present" on platforms where they are incorrectly reported as not
present by the AML and add the INT0002 device ID to the list of
"always present" devices (Hans de Goede).
- Fix the register information in the xpower PMIC driver and add
comments to map the registers to symbols used by AML to it
(Hans de Goede).
- Move the code turning off unused ACPI power resources during
system resume to a point after all devices have been resumed
to avoid issues with power resources that do not behave as
expected (Hans de Goede).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Ytsi
-----END PGP SIGNATURE-----
Merge tag 'acpi-extra-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to upstream revision
20170303 which adds a few minor fixes and improvements, update ACPI
SoC drivers with new device IDs, platform-related information and
similar, fix the register information in the xpower PMIC driver,
introduce a concept of "always present" devices to the ACPI device
enumeration code and use it to fix a problem with one platform, and
fix a system resume issue related to power resources.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20170303
which includes:
* Minor fixes and improvements in the core code (Bob Moore,
Seunghun Han).
* Debugger fixes (Colin Ian King, Lv Zheng).
* Compiler/disassembler improvements (Bob Moore, David Box, Lv
Zheng).
* Build-related update (Lv Zheng).
- Add new device IDs and platform-related information to the ACPI
drivers for Intel (LPSS) and AMD (APD) SoCs (Hanjun Guo, Hans de
Goede).
- Make it possible to quirk ACPI-enumerated devices as "always
present" on platforms where they are incorrectly reported as not
present by the AML and add the INT0002 device ID to the list of
"always present" devices (Hans de Goede).
- Fix the register information in the xpower PMIC driver and add
comments to map the registers to symbols used by AML to it (Hans de
Goede).
- Move the code turning off unused ACPI power resources during system
resume to a point after all devices have been resumed to avoid
issues with power resources that do not behave as expected (Hans de
Goede)"
* tag 'acpi-extra-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (22 commits)
ACPI / power: Delay turning off unused power resources after suspend
ACPI / PMIC: xpower: Fix power_table addresses
ACPI / LPSS: Call pwm_add_table() for Bay Trail PWM device
ACPICA: Update version to 20170303
ACPICA: iasl: add ASL conversion tool
ACPICA: Local cache support: Allow small cache objects
ACPICA: Disassembler: Do not unconditionally remove temporary names
ACPICA: iasl: Fix IORT SMMU GSI disassembling
ACPICA: Cleanup AML opcode definitions, no functional change
ACPICA: Debugger: Add interpreter blocking mark for single-step mode
ACPICA: debugger: fix memory leak on Pathname
ACPICA: Update for automatic repair code for objects returned by evaluate_object
ACPICA: Namespace: fix operand cache leak
ACPICA: Fix several incorrect invocations of ACPICA return macro
ACPICA: Fix a module for excessive debug output
ACPICA: Update some function headers, no funtional change
ACPICA: Disassembler: Enhance resource descriptor detection
i2c: designware: Add ACPI HID for Hisilicon Hip07/08 I2C controller
ACPI / APD: Add clock frequency for Hisilicon Hip07/08 I2C controller
ACPI / bus: Add INT0002 to list of always-present devices
...
- Add Intel Gemini Lake CPU IDs to the intel_idle and intel_rapl
drivers (David Box).
- Add a NULL pointer check to the cpuidle core to prevent it from
crashing on platforms with incomplete cpuidle configuration (Fei
Li).
- Fix DT-related documentation in the generic power domains (genpd)
framework and add a MAINTAINERS entry for DT-related material in
genpd (Viresh Kumar).
- Update the system suspend/resume infrastructure to improve the
handling of aborts of suspend transitions in progress in the
wakeup framework and rework the suspend-to-idle core loop to make
it possible to filter out spurious wakeup events (specifically the
ones coming from ACPI) without resuming all the way up to user
space every time (Rafael Wysocki).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=K1Q+
-----END PGP SIGNATURE-----
Merge tag 'pm-extra-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These add new CPU IDs to a couple of drivers, fix a possible NULL
pointer dereference in the cpuidle core, update DT-related things in
the generic power domains framework and finally update the
suspend/resume infrastructure to improve the handling of wakeups from
suspend-to-idle.
Specifics:
- Add Intel Gemini Lake CPU IDs to the intel_idle and intel_rapl
drivers (David Box).
- Add a NULL pointer check to the cpuidle core to prevent it from
crashing on platforms with incomplete cpuidle configuration (Fei
Li).
- Fix DT-related documentation in the generic power domains (genpd)
framework and add a MAINTAINERS entry for DT-related material in
genpd (Viresh Kumar).
- Update the system suspend/resume infrastructure to improve the
handling of aborts of suspend transitions in progress in the wakeup
framework and rework the suspend-to-idle core loop to make it
possible to filter out spurious wakeup events (specifically the
ones coming from ACPI) without resuming all the way up to user
space every time (Rafael Wysocki)"
* tag 'pm-extra-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / sleep: Ignore spurious SCI wakeups from suspend-to-idle
PM / wakeup: Integrate mechanism to abort transitions in progress
x86/intel_idle: add Gemini Lake support
cpuidle: check dev before usage in cpuidle_use_deepest_state()
powercap: intel_rapl: Add support for Gemini Lake
PM / Domains: Add DT file to MAINTAINERS
PM / Domains: Fix DT example
This includes:
* Some code optimizations for the Intel VT-d driver
* Code to switch off a previously enabled Intel IOMMU
* Support for 'struct iommu_device' for OMAP, Rockchip and
Mediatek IOMMUs
* Some header optimizations for IOMMU core code headers and a
few fixes that became necessary in other parts of the kernel
because of that
* ACPI/IORT updates and fixes
* Some Exynos IOMMU optimizations
* Code updates for the IOMMU dma-api code to bring it closer to
use per-cpu iova caches
* New command-line option to set default domain type allocated
by the iommu core code
* Another command line option to allow the Intel IOMMU switched
off in a tboot environment
* ARM/SMMU: TLB sync optimisations for SMMUv2, Support for using
an IDENTITY domain in conjunction with DMA ops, Support for
SMR masking, Support for 16-bit ASIDs (was previously broken)
* Various other small fixes and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=3aE8
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- code optimizations for the Intel VT-d driver
- ability to switch off a previously enabled Intel IOMMU
- support for 'struct iommu_device' for OMAP, Rockchip and Mediatek
IOMMUs
- header optimizations for IOMMU core code headers and a few fixes that
became necessary in other parts of the kernel because of that
- ACPI/IORT updates and fixes
- Exynos IOMMU optimizations
- updates for the IOMMU dma-api code to bring it closer to use per-cpu
iova caches
- new command-line option to set default domain type allocated by the
iommu core code
- another command line option to allow the Intel IOMMU switched off in
a tboot environment
- ARM/SMMU: TLB sync optimisations for SMMUv2, Support for using an
IDENTITY domain in conjunction with DMA ops, Support for SMR masking,
Support for 16-bit ASIDs (was previously broken)
- various other small fixes and improvements
* tag 'iommu-updates-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (63 commits)
soc/qbman: Move dma-mapping.h include to qman_priv.h
soc/qbman: Fix implicit header dependency now causing build fails
iommu: Remove trace-events include from iommu.h
iommu: Remove pci.h include from trace/events/iommu.h
arm: dma-mapping: Don't override dma_ops in arch_setup_dma_ops()
ACPI/IORT: Fix CONFIG_IOMMU_API dependency
iommu/vt-d: Don't print the failure message when booting non-kdump kernel
iommu: Move report_iommu_fault() to iommu.c
iommu: Include device.h in iommu.h
x86, iommu/vt-d: Add an option to disable Intel IOMMU force on
iommu/arm-smmu: Return IOVA in iova_to_phys when SMMU is bypassed
iommu/arm-smmu: Correct sid to mask
iommu/amd: Fix incorrect error handling in amd_iommu_bind_pasid()
iommu: Make iommu_bus_notifier return NOTIFY_DONE rather than error code
omap3isp: Remove iommu_group related code
iommu/omap: Add iommu-group support
iommu/omap: Make use of 'struct iommu_device'
iommu/omap: Store iommu_dev pointer in arch_data
iommu/omap: Move data structures to omap-iommu.h
iommu/omap: Drop legacy-style device support
...
* acpica:
ACPICA: Update version to 20170303
ACPICA: iasl: add ASL conversion tool
ACPICA: Local cache support: Allow small cache objects
ACPICA: Disassembler: Do not unconditionally remove temporary names
ACPICA: iasl: Fix IORT SMMU GSI disassembling
ACPICA: Cleanup AML opcode definitions, no functional change
ACPICA: Debugger: Add interpreter blocking mark for single-step mode
ACPICA: debugger: fix memory leak on Pathname
ACPICA: Update for automatic repair code for objects returned by evaluate_object
ACPICA: Namespace: fix operand cache leak
ACPICA: Fix several incorrect invocations of ACPICA return macro
ACPICA: Fix a module for excessive debug output
ACPICA: Update some function headers, no funtional change
ACPICA: Disassembler: Enhance resource descriptor detection
ACPICA: Add non-linux host build support
* pm-domains:
PM / Domains: Add DT file to MAINTAINERS
PM / Domains: Fix DT example
* pm-cpuidle:
x86/intel_idle: add Gemini Lake support
cpuidle: check dev before usage in cpuidle_use_deepest_state()
* pm-sleep:
ACPI / sleep: Ignore spurious SCI wakeups from suspend-to-idle
PM / wakeup: Integrate mechanism to abort transitions in progress
* powercap:
powercap: intel_rapl: Add support for Gemini Lake
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=eE4D
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add framework for supporting PCIe devices in Endpoint mode (Kishon
Vijay Abraham I)
- use non-postable PCI config space mappings when possible (Lorenzo
Pieralisi)
- clean up and unify mmap of PCI BARs (David Woodhouse)
- export and unify Function Level Reset support (Christoph Hellwig)
- avoid FLR for Intel 82579 NICs (Sasha Neftin)
- add pci_request_irq() and pci_free_irq() helpers (Christoph Hellwig)
- short-circuit config access failures for disconnected devices (Keith
Busch)
- remove D3 sleep delay when possible (Adrian Hunter)
- freeze PME scan before suspending devices (Lukas Wunner)
- stop disabling MSI/MSI-X in pci_device_shutdown() (Prarit Bhargava)
- disable boot interrupt quirk for ASUS M2N-LR (Stefan Assmann)
- add arch-specific alignment control to improve device passthrough by
avoiding multiple BARs in a page (Yongji Xie)
- add sysfs sriov_drivers_autoprobe to control VF driver binding
(Bodong Wang)
- allow slots below PCI-to-PCIe "reverse bridges" (Bjorn Helgaas)
- fix crashes when unbinding host controllers that don't support
removal (Brian Norris)
- add driver for MicroSemi Switchtec management interface (Logan
Gunthorpe)
- add driver for Faraday Technology FTPCI100 host bridge (Linus
Walleij)
- add i.MX7D support (Andrey Smirnov)
- use generic MSI support for Aardvark (Thomas Petazzoni)
- make Rockchip driver modular (Brian Norris)
- advertise 128-byte Read Completion Boundary support for Rockchip
(Shawn Lin)
- advertise PCI_EXP_LNKSTA_SLC for Rockchip root port (Shawn Lin)
- convert atomic_t to refcount_t in HV driver (Elena Reshetova)
- add CPU IRQ affinity in HV driver (K. Y. Srinivasan)
- fix PCI bus removal in HV driver (Long Li)
- add support for ThunderX2 DMA alias topology (Jayachandran C)
- add ThunderX pass2.x 2nd node MCFG quirk (Tomasz Nowicki)
- add ITE 8893 bridge DMA alias quirk (Jarod Wilson)
- restrict Cavium ACS quirk only to CN81xx/CN83xx/CN88xx devices
(Manish Jaggi)
* tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (146 commits)
PCI: Don't allow unbinding host controllers that aren't prepared
ARM: DRA7: clockdomain: Change the CLKTRCTRL of CM_PCIE_CLKSTCTRL to SW_WKUP
MAINTAINERS: Add PCI Endpoint maintainer
Documentation: PCI: Add userguide for PCI endpoint test function
tools: PCI: Add sample test script to invoke pcitest
tools: PCI: Add a userspace tool to test PCI endpoint
Documentation: misc-devices: Add Documentation for pci-endpoint-test driver
misc: Add host side PCI driver for PCI test function device
PCI: Add device IDs for DRA74x and DRA72x
dt-bindings: PCI: dra7xx: Add DT bindings to enable unaligned access
PCI: dwc: dra7xx: Workaround for errata id i870
dt-bindings: PCI: dra7xx: Add DT bindings for PCI dra7xx EP mode
PCI: dwc: dra7xx: Add EP mode support
PCI: dwc: dra7xx: Facilitate wrapper and MSI interrupts to be enabled independently
dt-bindings: PCI: Add DT bindings for PCI designware EP mode
PCI: dwc: designware: Add EP mode support
Documentation: PCI: Add binding documentation for pci-test endpoint function
ixgbe: Use pcie_flr() instead of duplicating it
IB/hfi1: Use pcie_flr() instead of duplicating it
PCI: imx6: Fix spelling mistake: "contol" -> "control"
...
This typo is quite common. Fix it and add it to the spelling file so
that checkpatch catches it earlier.
Link: http://lkml.kernel.org/r/20170317011131.6881-2-sboyd@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are many code paths opencoding kvmalloc. Let's use the helper
instead. The main difference to kvmalloc is that those users are
usually not considering all the aspects of the memory allocator. E.g.
allocation requests <= 32kB (with 4kB pages) are basically never failing
and invoke OOM killer to satisfy the allocation. This sounds too
disruptive for something that has a reasonable fallback - the vmalloc.
On the other hand those requests might fallback to vmalloc even when the
memory allocator would succeed after several more reclaim/compaction
attempts previously. There is no guarantee something like that happens
though.
This patch converts many of those places to kv[mz]alloc* helpers because
they are more conservative.
Link: http://lkml.kernel.org/r/20170306103327.2766-2-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> # Xen bits
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Andreas Dilger <andreas.dilger@intel.com> # Lustre
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com> # KVM/s390
Acked-by: Dan Williams <dan.j.williams@intel.com> # nvdim
Acked-by: David Sterba <dsterba@suse.com> # btrfs
Acked-by: Ilya Dryomov <idryomov@gmail.com> # Ceph
Acked-by: Tariq Toukan <tariqt@mellanox.com> # mlx4
Acked-by: Leon Romanovsky <leonro@mellanox.com> # mlx5
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Colin Cross <ccross@android.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Santosh Raspatur <santosh@chelsio.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Yishai Hadas <yishaih@mellanox.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: "Yan, Zheng" <zyan@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Region media error reporting: A libnvdimm region device is the parent
to one or more namespaces. To date, media errors have been reported via
the "badblocks" attribute attached to pmem block devices for namespaces
in "raw" or "memory" mode. Given that namespaces can be in "device-dax"
or "btt-sector" mode this new interface reports media errors
generically, i.e. independent of namespace modes or state. This
subsequently allows userspace tooling to craft "ACPI 6.1 Section
9.20.7.6 Function Index 4 - Clear Uncorrectable Error" requests and
submit them via the ioctl path for NVDIMM root bus devices.
* Introduce 'struct dax_device' and 'struct dax_operations': Prompted by
a request from Linus and feedback from Christoph this allows for dax
capable drivers to publish their own custom dax operations. This fixes
the broken assumption that all dax operations are related to a
persistent memory device, and makes it easier for other architectures
and platforms to add customized persistent memory support.
* 'libnvdimm' core updates: A new "deep_flush" sysfs attribute is
available for storage appliance applications to manually trigger memory
controllers to drain write-pending buffers that would otherwise be
flushed automatically by the platform ADR (asynchronous-DRAM-refresh)
mechanism at a power loss event. Support for "locked" DIMMs is included
to prevent namespaces from surfacing when the namespace label data area
is locked. Finally, fixes for various reported deadlocks and crashes,
also tagged for -stable.
* ACPI / nfit driver updates: General updates of the nfit driver to add
DSM command overrides, ACPI 6.1 health state flags support, DSM payload
debug available by default, and various fixes.
Acknowledgements that came after the branch was pushed:
commmit 565851c972 "device-dax: fix sysfs attribute deadlock"
Tested-by: Yi Zhang <yizhan@redhat.com>
commit 23f4984483 "libnvdimm: rework region badblocks clearing"
Tested-by: Toshi Kani <toshi.kani@hpe.com>
-----BEGIN PGP SIGNATURE-----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=Ox0s
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"The bulk of this has been in multiple -next releases. There were a few
late breaking fixes and small features that got added in the last
couple days, but the whole set has received a build success
notification from the kbuild robot.
Change summary:
- Region media error reporting: A libnvdimm region device is the
parent to one or more namespaces. To date, media errors have been
reported via the "badblocks" attribute attached to pmem block
devices for namespaces in "raw" or "memory" mode. Given that
namespaces can be in "device-dax" or "btt-sector" mode this new
interface reports media errors generically, i.e. independent of
namespace modes or state.
This subsequently allows userspace tooling to craft "ACPI 6.1
Section 9.20.7.6 Function Index 4 - Clear Uncorrectable Error"
requests and submit them via the ioctl path for NVDIMM root bus
devices.
- Introduce 'struct dax_device' and 'struct dax_operations': Prompted
by a request from Linus and feedback from Christoph this allows for
dax capable drivers to publish their own custom dax operations.
This fixes the broken assumption that all dax operations are
related to a persistent memory device, and makes it easier for
other architectures and platforms to add customized persistent
memory support.
- 'libnvdimm' core updates: A new "deep_flush" sysfs attribute is
available for storage appliance applications to manually trigger
memory controllers to drain write-pending buffers that would
otherwise be flushed automatically by the platform ADR
(asynchronous-DRAM-refresh) mechanism at a power loss event.
Support for "locked" DIMMs is included to prevent namespaces from
surfacing when the namespace label data area is locked. Finally,
fixes for various reported deadlocks and crashes, also tagged for
-stable.
- ACPI / nfit driver updates: General updates of the nfit driver to
add DSM command overrides, ACPI 6.1 health state flags support, DSM
payload debug available by default, and various fixes.
Acknowledgements that came after the branch was pushed:
- commmit 565851c972 "device-dax: fix sysfs attribute deadlock":
Tested-by: Yi Zhang <yizhan@redhat.com>
- commit 23f4984483 "libnvdimm: rework region badblocks clearing"
Tested-by: Toshi Kani <toshi.kani@hpe.com>"
* tag 'libnvdimm-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (52 commits)
libnvdimm, pfn: fix 'npfns' vs section alignment
libnvdimm: handle locked label storage areas
libnvdimm: convert NDD_ flags to use bitops, introduce NDD_LOCKED
brd: fix uninitialized use of brd->dax_dev
block, dax: use correct format string in bdev_dax_supported
device-dax: fix sysfs attribute deadlock
libnvdimm: restore "libnvdimm: band aid btt vs clear poison locking"
libnvdimm: fix nvdimm_bus_lock() vs device_lock() ordering
libnvdimm: rework region badblocks clearing
acpi, nfit: kill ACPI_NFIT_DEBUG
libnvdimm: fix clear length of nvdimm_forget_poison()
libnvdimm, pmem: fix a NULL pointer BUG in nd_pmem_notify
libnvdimm, region: sysfs trigger for nvdimm_flush()
libnvdimm: fix phys_addr for nvdimm_clear_poison
x86, dax, pmem: remove indirection around memcpy_from_pmem()
block: remove block_device_operations ->direct_access()
block, dax: convert bdev_dax_supported() to dax_direct_access()
filesystem-dax: convert to dax_direct_access()
Revert "block: use DAX for partition table reads"
ext2, ext4, xfs: retrieve dax_device for iomap operations
...
The ACPI SCI (System Control Interrupt) is set up as a wakeup IRQ
during suspend-to-idle transitions and, consequently, any events
signaled through it wake up the system from that state. However,
on some systems some of the events signaled via the ACPI SCI while
suspended to idle should not cause the system to wake up. In fact,
quite often they should just be discarded.
Arguably, systems should not resume entirely on such events, but in
order to decide which events really should cause the system to resume
and which are spurious, it is necessary to resume up to the point
when ACPI SCIs are actually handled and processed, which is after
executing dpm_resume_noirq() in the system resume path.
For this reasons, add a loop around freeze_enter() in which the
platforms can process events signaled via multiplexed IRQ lines
like the ACPI SCI and add suspend-to-idle hooks that can be
used for this purpose to struct platform_freeze_ops.
In the ACPI case, the ->wake hook is used for checking if the SCI
has triggered while suspended and deferring the interrupt-induced
system wakeup until the events signaled through it are actually
processed sufficiently to decide whether or not the system should
resume. In turn, the ->sync hook allows all of the relevant event
queues to be flushed so as to prevent events from being missed due
to race conditions.
In addition to that, some ACPI code processing wakeup events needs
to be modified to use the "hard" version of wakeup triggers, so that
it will cause a system resume to happen on device-induced wakeup
events even if the "soft" mechanism to prevent the system from
suspending is not enabled (that also helps to catch device-induced
wakeup events occurring during suspend transitions in progress).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- kdump support, including two necessary memblock additions:
memblock_clear_nomap() and memblock_cap_memory_range()
- ARMv8.3 HWCAP bits for JavaScript conversion instructions, complex
numbers and weaker release consistency
- arm64 ACPI platform MSI support
- arm perf updates: ACPI PMU support, L3 cache PMU in some Qualcomm
SoCs, Cortex-A53 L2 cache events and DTLB refills, MAINTAINERS update
for DT perf bindings
- architected timer errata framework (the arch/arm64 changes only)
- support for DMA_ATTR_FORCE_CONTIGUOUS in the arm64 iommu DMA API
- arm64 KVM refactoring to use common system register definitions
- remove support for ASID-tagged VIVT I-cache (no ARMv8 implementation
using it and deprecated in the architecture) together with some
I-cache handling clean-up
- PE/COFF EFI header clean-up/hardening
- define BUG() instruction without CONFIG_BUG
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SDkm
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- kdump support, including two necessary memblock additions:
memblock_clear_nomap() and memblock_cap_memory_range()
- ARMv8.3 HWCAP bits for JavaScript conversion instructions, complex
numbers and weaker release consistency
- arm64 ACPI platform MSI support
- arm perf updates: ACPI PMU support, L3 cache PMU in some Qualcomm
SoCs, Cortex-A53 L2 cache events and DTLB refills, MAINTAINERS update
for DT perf bindings
- architected timer errata framework (the arch/arm64 changes only)
- support for DMA_ATTR_FORCE_CONTIGUOUS in the arm64 iommu DMA API
- arm64 KVM refactoring to use common system register definitions
- remove support for ASID-tagged VIVT I-cache (no ARMv8 implementation
using it and deprecated in the architecture) together with some
I-cache handling clean-up
- PE/COFF EFI header clean-up/hardening
- define BUG() instruction without CONFIG_BUG
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (92 commits)
arm64: Fix the DMA mmap and get_sgtable API with DMA_ATTR_FORCE_CONTIGUOUS
arm64: Print DT machine model in setup_machine_fdt()
arm64: pmu: Wire-up Cortex A53 L2 cache events and DTLB refills
arm64: module: split core and init PLT sections
arm64: pmuv3: handle pmuv3+
arm64: Add CNTFRQ_EL0 trap handler
arm64: Silence spurious kbuild warning on menuconfig
arm64: pmuv3: use arm_pmu ACPI framework
arm64: pmuv3: handle !PMUv3 when probing
drivers/perf: arm_pmu: add ACPI framework
arm64: add function to get a cpu's MADT GICC table
drivers/perf: arm_pmu: split out platform device probe logic
drivers/perf: arm_pmu: move irq request/free into probe
drivers/perf: arm_pmu: split cpu-local irq request/free
drivers/perf: arm_pmu: rename irq request/free functions
drivers/perf: arm_pmu: handle no platform_device
drivers/perf: arm_pmu: simplify cpu_pmu_request_irqs()
drivers/perf: arm_pmu: factor out pmu registration
drivers/perf: arm_pmu: fold init into alloc
drivers/perf: arm_pmu: define armpmu_init_fn
...
Per the latest version of the "NVDIMM DSM Interface Example" [1], the
label data retrieval routine can report a "locked" status. In this case
all regions associated with that DIMM are disabled until the label area
is unlocked. Provide generic libnvdimm enabling for NVDIMMs with label
data area locking capabilities.
[1]: http://pmem.io/documents/
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This is a preparation patch for handling locked nvdimm label regions, a
new concept as introduced by the latest DSM document on pmem.io [1]. A
future patch will leverage nvdimm_set_locked() at DIMM probe time to
flag regions that can not be enabled. There should be no functional
difference resulting from this change.
[1]: http://pmem.io/documents/NVDIMM_DSM_Interface_Example-V1.3.pdf
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There's quite a lot of small driver specific fixes and enhancements in
this release but the main activity has been around the loopback and
spidev test drivers which is good to see as it should hopefully help
improve the quality of all the drivers as people start to make use of
the new code:
- Additional tests in the loopback test driver for vmalloc()
compatibility and around delays together with fixes for existing
tests.
- Support for testing continuous data transfer for use in soak testing.
- Device property support for board info platforms.
- Support for registering empty sets of devices via board info (useful
when writing code to enumerate hardware automatically).
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlkJ81ETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0HQZB/9IO6RQmdIU8A2s0xBaXOI64uE9ajFQ
aPcwtWwpsAyxSHYtDbsPrcVuLTaJm3q+ldNJt7stYTkRG7R5W6bx+oiJOx1VdkbY
QJiUQUYNpAj5H0EIPocTFct8Yq+SfVtEeEwAuEnu/DouTXLPSoxoQ0dua+iyesxL
ZF6T+/zyRyj+zoijHGbYQEDs6jKuZudtMzQAFoJEalr3ywEDyBMUghXbkfk1qJd4
9XD1Vr4wFUYJ/7yPdwzfhG8u8FHmIBob3L2w6MPvNB961lnaQUCxuRKy3cJZrQM8
fn3WJAzrnsA6SOTM+rskWhWh4j0t26XgY/xCsEdiE+XGIh6Sd1RPQuJM
=e4MH
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"There's quite a lot of small driver specific fixes and enhancements in
this release but the main activity has been around the loopback and
spidev test drivers which is good to see as it should hopefully help
improve the quality of all the drivers as people start to make use of
the new code:
- Additional tests in the loopback test driver for vmalloc()
compatibility and around delays together with fixes for existing
tests.
- Support for testing continuous data transfer for use in soak
testing.
- Device property support for board info platforms.
- Support for registering empty sets of devices via board info
(useful when writing code to enumerate hardware automatically)"
* tag 'spi-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (52 commits)
spi: cadence: Allow for GPIO pins to be used as chipselects
spi-imx: Implements handling of the SPI_READY mode flag.
spi: tegra: fix spelling mistake: "trasfer" -> "transfer"
spi: spi-ti-qspi: Use bounce buffer if read buffer is not DMA'ble
spi: Add can_dma like interface for spi_flash_read
spi: dw: Disable clock after unregistering the host
spi: double time out tolerance
spi: atmel: add deepest PM support to SAMA5D2
spi: atmel: factorize reusable code for SPI controller init
spi: orion: add LSB support
spi: pl022: don't use uninitialized variable
spi: loopback-test: fix spelling mistake: "minimam" -> "minimum"
spi: dynamycally allocated message initialization
spi: spi-ti-qspi: Remove unused dma_dev variable
spi: omap2-mcspi: poll OMAP2_MCSPI_CHSTAT_RXS for PIO transfer
spi: spi-ti-qspi: Use dma_engine wrapper for dma memcpy call
spi: spidev_test: add option to continuously transfer data
spi: loopback-test: fix potential integer overflow on multiple
spi: sun6i: update max transfer size reported
spi: pl022: Document property values
...
- restore powerpc dumping; Ankit Kumar
- fix more bugs in the rarely exercises module unloading logic
- reorganize filesystem locking to fix problems noticed by lockdep
- refactor internal pstore APIs to make development and review easier:
- improve error reporting
- add kernel-doc structure and function comments
- avoid insane argument passing by using a common record structure
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
Comment: Kees Cook <kees@outflux.net>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=S14G
-----END PGP SIGNATURE-----
Merge tag 'pstore-v4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore updates from Kees Cook:
"This has a large internal refactoring along with several smaller
fixes.
- constify compression structures; Bhumika Goyal
- restore powerpc dumping; Ankit Kumar
- fix more bugs in the rarely exercises module unloading logic
- reorganize filesystem locking to fix problems noticed by lockdep
- refactor internal pstore APIs to make development and review
easier:
- improve error reporting
- add kernel-doc structure and function comments
- avoid insane argument passing by using a common record
structure"
* tag 'pstore-v4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (23 commits)
pstore: Solve lockdep warning by moving inode locks
pstore: Fix flags to enable dumps on powerpc
pstore: Remove unused vmalloc.h in pmsg
pstore: simplify write_user_compat()
pstore: Remove write_buf() callback
pstore: Replace arguments for write_buf_user() API
pstore: Replace arguments for write_buf() API
pstore: Replace arguments for erase() API
pstore: Do not duplicate record metadata
pstore: Allocate records on heap instead of stack
pstore: Pass record contents instead of copying
pstore: Always allocate buffer for decompression
pstore: Replace arguments for write() API
pstore: Replace arguments for read() API
pstore: Switch pstore_mkfile to pass record
pstore: Move record decompression to function
pstore: Extract common arguments into structure
pstore: Add kernel-doc for struct pstore_info
pstore: Improve register_pstore() error reporting
pstore: Avoid race in module unloading
...
Pull x86 boot updates from Ingo Molnar:
"The biggest changes in this cycle were:
- reworking of the e820 code: separate in-kernel and boot-ABI data
structures and apply a whole range of cleanups to the kernel side.
No change in functionality.
- enable KASLR by default: it's used by all major distros and it's
out of the experimental stage as well.
- ... misc fixes and cleanups"
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (63 commits)
x86/KASLR: Fix kexec kernel boot crash when KASLR randomization fails
x86/reboot: Turn off KVM when halting a CPU
x86/boot: Fix BSS corruption/overwrite bug in early x86 kernel startup
x86: Enable KASLR by default
boot/param: Move next_arg() function to lib/cmdline.c for later reuse
x86/boot: Fix Sparse warning by including required header file
x86/boot/64: Rename start_cpu()
x86/xen: Update e820 table handling to the new core x86 E820 code
x86/boot: Fix pr_debug() API braindamage
xen, x86/headers: Add <linux/device.h> dependency to <asm/xen/page.h>
x86/boot/e820: Simplify e820__update_table()
x86/boot/e820: Separate the E820 ABI structures from the in-kernel structures
x86/boot/e820: Fix and clean up e820_type switch() statements
x86/boot/e820: Rename the remaining E820 APIs to the e820__*() prefix
x86/boot/e820: Remove unnecessary #include's
x86/boot/e820: Rename e820_mark_nosave_regions() to e820__register_nosave_regions()
x86/boot/e820: Rename e820_reserve_resources*() to e820__reserve_resources*()
x86/boot/e820: Use bool in query APIs
x86/boot/e820: Document e820__reserve_setup_data()
x86/boot/e820: Clean up __e820__update_table() et al
...
Pull RAS updates from Ingo Molnar:
"The main changes in this cycle were:
- add the 'Corrected Errors Collector' kernel feature which collect
and monitor correctable errors statistics and will preemptively
(soft-)offline physical pages that have a suspiciously high error
count.
- handle MCE errors during kexec() more gracefully
- factor out and deprecate the /dev/mcelog driver
- ... plus misc fixes and cleanpus"
* 'ras-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Check MCi_STATUS[MISCV] for usable addr on Intel only
ACPI/APEI: Use setup_deferrable_timer()
x86/mce: Update notifier priority check
x86/mce: Enable PPIN for Knights Landing/Mill
x86/mce: Do not register notifiers with invalid prio
x86/mce: Factor out and deprecate the /dev/mcelog driver
RAS: Add a Corrected Errors Collector
x86/mce: Rename mce_log to mce_log_buffer
x86/mce: Rename mce_log()'s argument
x86/mce: Init some CPU features early
x86/mce: Handle broadcasted MCE gracefully with kexec
Pull EFI updates from Ingo Molnar:
"The main changes in this cycle were:
- move BGRT handling to drivers/acpi so it can be shared between x86
and ARM
- bring the EFI stub's initrd and FDT allocation logic in line with
the latest changes to the arm64 boot protocol
- improvements and fixes to the EFI stub's command line parsing
routines
- randomize the virtual mapping of the UEFI runtime services on
ARM/arm64
- ... and other misc enhancements, cleanups and fixes"
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/libstub/arm: Don't use TASK_SIZE when randomizing the RT space
ef/libstub/arm/arm64: Randomize the base of the UEFI rt services region
efi/libstub/arm/arm64: Disable debug prints on 'quiet' cmdline arg
efi/libstub: Unify command line param parsing
efi/libstub: Fix harmless command line parsing bug
efi/arm32-stub: Allow boot-time allocations in the vmlinux region
x86/efi: Clean up a minor mistake in comment
efi/pstore: Return error code (if any) from efi_pstore_write()
efi/bgrt: Enable ACPI BGRT handling on arm64
x86/efi/bgrt: Move efi-bgrt handling out of arch/x86
efi/arm-stub: Round up FDT allocation to mapping size
efi/arm-stub: Correct FDT and initrd allocation rules for arm64
Pull timer updates from Thomas Gleixner:
"The timer departement delivers:
- more year 2038 rework
- a massive rework of the arm achitected timer
- preparatory patches to allow NTP correction of clock event devices
to avoid early expiry
- the usual pile of fixes and enhancements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (91 commits)
timer/sysclt: Restrict timer migration sysctl values to 0 and 1
arm64/arch_timer: Mark errata handlers as __maybe_unused
Clocksource/mips-gic: Remove redundant non devicetree init
MIPS/Malta: Probe gic-timer via devicetree
clocksource: Use GENMASK_ULL in definition of CLOCKSOURCE_MASK
acpi/arm64: Add SBSA Generic Watchdog support in GTDT driver
clocksource: arm_arch_timer: add GTDT support for memory-mapped timer
acpi/arm64: Add memory-mapped timer support in GTDT driver
clocksource: arm_arch_timer: simplify ACPI support code.
acpi/arm64: Add GTDT table parse driver
clocksource: arm_arch_timer: split MMIO timer probing.
clocksource: arm_arch_timer: add structs to describe MMIO timer
clocksource: arm_arch_timer: move arch_timer_needs_of_probing into DT init call
clocksource: arm_arch_timer: refactor arch_timer_needs_probing
clocksource: arm_arch_timer: split dt-only rate handling
x86/uv/time: Set ->min_delta_ticks and ->max_delta_ticks
unicore32/time: Set ->min_delta_ticks and ->max_delta_ticks
um/time: Set ->min_delta_ticks and ->max_delta_ticks
tile/time: Set ->min_delta_ticks and ->max_delta_ticks
score/time: Set ->min_delta_ticks and ->max_delta_ticks
...
- Extend the ACPI _DSD properties code and the generic device
properties framework to support the concept of remote endponts
(Mika Westerberg, Sakari Ailus).
- Document the support for ports and endpoints in _DSD properties
and extend the generic device properties framework to make it
more suitable for the handling of ports and endpoints (Sakari
Ailus).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Ihme
-----END PGP SIGNATURE-----
Merge tag 'devprop-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull generic device properties framework updates from Rafael Wysocki:
"These add support for the ports and endpoints concepts, based on the
existing DT support for them, to the generic device properties
framework and update the ACPI _DSD properties code to recognize ports
and endpoints accordingly.
Specifics:
- Extend the ACPI _DSD properties code and the generic device
properties framework to support the concept of remote endponts
(Mika Westerberg, Sakari Ailus).
- Document the support for ports and endpoints in _DSD properties and
extend the generic device properties framework to make it more
suitable for the handling of ports and endpoints (Sakari Ailus)"
* tag 'devprop-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
device property: Read strings using string array reading functions
device property: fwnode_property_read_string_array() returns nr of strings
device property: Fix reading pset strings using array access functions
device property: fwnode_property_read_string_array() may return -EILSEQ
ACPI / DSD: Document references, ports and endpoints
device property: Add fwnode_get_next_parent()
device property: Add support for fwnode endpoints
device property: Make dev_fwnode() public
of: Add of_fwnode_handle() to convert device nodes to fwnode_handle
device property: Add fwnode_handle_get()
device property: Add support for remote endpoints
ACPI / property: Add support for remote endpoints
device property: Add fwnode_get_named_child_node()
ACPI / property: Add fwnode_get_next_child_node()
device property: Add fwnode_get_parent()
ACPI / property: Add possiblity to retrieve parent firmware node
- Update the core device enumeration code to make it more internally
consistent and robust and drop the force_remove sysfs attribute
that could be used to tell it to ignore errors on device
hot-removal which was dangerous in general and no real and
still relevant use cases for it could be found (Rafael Wysocki,
Michal Hocko).
- Make the core device enumeration code use _PXM to associate
platform devices created by it with specific NUMA nodes (Shanker
Donthineni).
- Extend the CPPC library by adding more sysfs entries for
performance capabilities to it and making it use the lowest
nonlinear performance parameter (Prashanth Prakash).
- Make the CPU online more consistent with CPU initialization in
the ACPI processor driver (Prashanth Prakash).
- Update the AC and battery drivers to help them avoid attaching to
devices that cannot be handled by them and update the axp288_charger
power supply driver to work correctly on ACPI systems without the
INT3496 device (Hans de Goede).
- Add an ACPI operation region driver for the Intel CHT Whiskey Cove
PMIC and update the xpower operation region driver to work without
IIO which isn't really necessary for it to work (Hans de Goede).
- Add a new entry for Dell Inspiron 7537 to the _REV quirk blacklist
(Kai Heng Feng).
- Make the code in the ACPI video driver easier to follow by adding
symbols and comments to it (Dmitry Frank).
- Update ACPI documentation and drop a function that has no users
from the tables-handling code (Cao jin, Baoquan He).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=IwcL
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These are some device enumeration code changes, updates of the AC and
battery drivers to help them avoid attaching to devices that cannot be
handled by them, new operation region driver for the Intel CHT Whiskey
Cove PMIC, new sysfs entries for CPPC performance capabilities, a new
_REV quirk blacklist entry and a couple of assorted minor fixes and
cleanups.
Specifics:
- Update the core device enumeration code to make it more internally
consistent and robust and drop the force_remove sysfs attribute
that could be used to tell it to ignore errors on device
hot-removal which was dangerous in general and no real and still
relevant use cases for it could be found (Rafael Wysocki, Michal
Hocko).
- Make the core device enumeration code use _PXM to associate
platform devices created by it with specific NUMA nodes (Shanker
Donthineni).
- Extend the CPPC library by adding more sysfs entries for
performance capabilities to it and making it use the lowest
nonlinear performance parameter (Prashanth Prakash).
- Make the CPU online more consistent with CPU initialization in the
ACPI processor driver (Prashanth Prakash).
- Update the AC and battery drivers to help them avoid attaching to
devices that cannot be handled by them and update the
axp288_charger power supply driver to work correctly on ACPI
systems without the INT3496 device (Hans de Goede).
- Add an ACPI operation region driver for the Intel CHT Whiskey Cove
PMIC and update the xpower operation region driver to work without
IIO which isn't really necessary for it to work (Hans de Goede).
- Add a new entry for Dell Inspiron 7537 to the _REV quirk blacklist
(Kai Heng Feng).
- Make the code in the ACPI video driver easier to follow by adding
symbols and comments to it (Dmitry Frank).
- Update ACPI documentation and drop a function that has no users
from the tables-handling code (Cao jin, Baoquan He)"
* tag 'acpi-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PMIC: Stop xpower OPRegion handler relying on IIO
ACPI / PMIC: Add opregion driver for Intel CHT Whiskey Cove PMIC
ACPI / scan: Avoid enumerating devices more than once
ACPI / scan: Apply default enumeration to devices with ACPI drivers
power: supply: axp288_charger: Only wait for INT3496 device if present
ACPI / AC: Add a blacklist with PMIC ACPI HIDs with a native charger driver
ACPI / battery: Add a blacklist with PMIC ACPI HIDs with a native battery driver
ACPI / battery: Fix acpi_battery_exit on acpi_battery_init_async errors
ACPI / utils: Add new acpi_dev_present helper
ACPI / video: add comments about subtle cases
ACPI / video: get rid of magic numbers and use enum instead
ACPI / doc: linuxized-acpica.txt: fix typos
ACPI / blacklist: add _REV quirk for Dell Inspiron 7537
ACPI / tables: Drop acpi_parse_entries() which is not used
ACPI / CPPC: add sysfs entries for CPPC perf capabilities
ACPI / CPPC: Read lowest nonlinear perf in cppc_get_perf_caps()
ACPI / platform: Update platform device NUMA node based on _PXM method
ACPI / Processor: Drop setup_max_cpus check from acpi_processor_add()
ACPI / scan: Drop support for force_remove
Commit 660b1113e0 (ACPI / PM: Fix consistency check for power resources
during resume) introduced a check for ACPI power resources which have
been turned on by the BIOS during suspend and turns these back off again.
This is causing problems on a Dell Venue Pro 11 7130 (i5-4300Y) it causes
the following messages to show up in dmesg:
[ 131.014605] ACPI: Waking up from system sleep state S3
[ 131.150271] acpi LNXPOWER:07: Turning OFF
[ 131.150323] acpi LNXPOWER:06: Turning OFF
[ 131.150911] acpi LNXPOWER:00: Turning OFF
[ 131.169014] ACPI : EC: interrupt unblocked
[ 131.181811] xhci_hcd 0000:00:14.0: System wakeup disabled by ACPI
[ 133.535728] pci_raw_set_power_state: 76 callbacks suppressed
[ 133.535735] iwlwifi 0000:01:00.0: Refused to change power state,
currently in D3
[ 133.597672] PM: noirq resume of devices complete after 2428.891 msecs
Followed by a bunch of iwlwifi errors later on and the pcie device
dropping from the bus (acpiphp thinks it has been unplugged).
Disabling the turning off of unused power resources fixes this. Instead
of adding a quirk for this system, this commit fixes this by moving the
disabling of unused power resources to later in the resume sequence
when the iwlwifi card has been moved out of D3 so the ref_count for
its power resource no longer is 0.
This new behavior seems to match the intend of the original commit which
commit-msg says: "(... which means that no devices are going to need them
any time soon) and we should turn them off".
This also avoids power resources which we need when bringing devices out
of D3 from getting bounced off and then back on again.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
would have issues at panic time cause by a recently
introduced change, a problem with device numbering,
one possible panic in the I2C driver (destined for
stable).
Nothing earth-shattering, but some things that need
to go in.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlkHLe4ACgkQIXnXXONXERctaACgtLPKwEc8IGFcdpQ6njZAJXm/
eNgAoIRDUTO3SstAWVtanbUEG8ao74gB
=3InS
-----END PGP SIGNATURE-----
Merge tag 'for-linux-4.12' of git://github.com/cminyard/linux-ipmi
Pull IPMI updates from Corey Minyard:
"A few fixes of things in the IPMI area, the watchdog would have issues
at panic time cause by a recently introduced change, a problem with
device numbering, one possible panic in the I2C driver (destined for
stable).
Nothing earth-shattering, but some things that need to go in"
* tag 'for-linux-4.12' of git://github.com/cminyard/linux-ipmi:
ipmi/watchdog: fix wdog hang on panic waiting for ipmi response
ipmi_si: use smi_num for init_name
ipmi: bt-bmc: Add ast2500 compatible string
ACPI / IPMI: change warning to debug on timeout
ACPI / IPMI: allow ACPI_IPMI with IPMI_SSIF
ipmi_ssif: use setup_timer
ipmi: Fix kernel panic at ipmi_ssif_thread()
Inevitably when one actually needs to debug a DSM issue it's on a
distribution kernel that has CONFIG_ACPI_NFIT_DEBUG=n. The config symbol
was only there to avoid the compile error due to the missing fallback for
print_hex_dump_debug in the CONFIG_DYNAMIC_DEBUG=n case. That was fixed
with commit cdf17449af "hexdump: do not print debug dumps for
!CONFIG_DEBUG", so the config symbol can just be dropped.
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The IOMMU probe deferral IORT rework had to add code in
iort_iommu_configure() and iort_iommu_xlate() that requires
the IOMMU_API to be selected in order to compile and work.
Stub out the pieces of code that depend on CONFIG_IOMMU_API
to be selected to prevent compilation failures such as:
drivers/acpi/arm64/iort.c: In function 'iort_iommu_xlate':
drivers/acpi/arm64/iort.c:647:22: error: 'struct iommu_fwspec' has no
member named 'ops'
by wrapping the code in static inline functions that provide a NOP
implementation when CONFIG_IOMMU_API is not selected.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The power table addresses should be contiguous, but there was a hole
where 0x34 was missing. On most devices this is not a problem as
addresses above 0x34 are used for the BUC# convertors which are not
used in the DSDTs I've access to but after the BUC# convertors
there is a field named GPI1 in the DSTDs, which does get used in some
cases and ended up turning BUC6 on and off due to the wrong addresses,
resulting in turning the entire device off (or causing it to reboot).
Removing the hole in the addresses fixes this, fixing one of my
Bay Trail tablets turning off while booting the mainline kernel.
While at it add comments with the field names used in the DSDTs to
make it easier to compare the register and bits used at each address
with the datasheet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On Bay Trail systems with a Crystal Cove PMIC the Crystal Cove's PWM is
used to control the backlight brightness. On systems without one, the
Crystal Cove SoC's PWM is used and we need to call pwm_add_table() so
that the i915 driver can find the pwm for controlling the backlight.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-scan:
ACPI / scan: Avoid enumerating devices more than once
ACPI / scan: Apply default enumeration to devices with ACPI drivers
ACPI / scan: Drop support for force_remove
* acpi-tables:
ACPI / tables: Drop acpi_parse_entries() which is not used
* acpi-platform:
ACPI / platform: Update platform device NUMA node based on _PXM method
ACPICA commit c04d310039d3e0ed1cb62876fe7e596fbc75ab01
ACPICA commit a65c1df7e6b4bad8e37df822018c40c6c446add9
The key feature of this utility is that the original comments within
the input ASL files are preserved during the conversion process, and
included within the converted ASL+ file -- thus creating a transparent
conversion of existing ASL files to ASL+ (ASL 2.0)
This patch is an automatic generation of the ASL converter commit,
Linux kernel isn't affected by the functionality provided in this
commit, but requires the linuxized changes to support future ACPICA
release automation.
Link: https://github.com/acpica/acpica/commit/c04d3100
Link: https://github.com/acpica/acpica/commit/a65c1df7
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Jung-uk Kim <jkim@FreeBSD.org>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Crystal Cove and Whiskey Cove are two different PMICs which are
installed on Intel Atom SoC based platforms.
Moreover there are two independent drivers that by some reason were
supposed (*) to get into one kernel module.
Fix the mess by clarifying Kconfig option for Crystal Cove and split
Whiskey Cove out of it.
(*) It looks like the configuration was never tested with
INTEL_SOC_PMIC=n. The line in Makefile is actually wrong.
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> (supporter:ACPI)
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
ACPICA commit 9c54b8bbd483421ef2fef5225c00f1655b4a491c
Remove apparently arbitrary restriction on the size of the cache
objects to 16 (in acpi_os_create_cache). Now, the input object
size must be simply non-zero.
Link: https://github.com/acpica/acpica/commit/9c54b8bb
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit c46f496df41e53a368f877f88b70bdfc9bd6fdbe
Change the Switch disassembly code to check if the conversion can be
done before removing temporary (_T_x) names. Prevents invalid
disassembly of AML created by older compilers (circa 2005).
Link: https://github.com/acpica/acpica/commit/c46f496d
Link: https://bugs.acpica.org/show_bug.cgi?id=1358
Link: https://bugs.acpica.org/show_bug.cgi?id=1360
Reported-by: racerrehabman@gmail.com
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit ec969d38fef3be95358e65f0dd071b5f2c045b6b
This change is a cleanup and further standardization of the AML
opcode defines in amlcode.h
Improves the readability and maintainability of the source code.
Link: https://github.com/acpica/acpica/commit/ec969d38
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 91af5d18cd40b35f9d5568fb95fc403ff12474e5
When the single-step mode is used, evaluation is actually split by the
single-step command prompts, so this patch correctly marks the evaluation
segment with interpreter lock release/acquire.
This in return fixes an issue that in the single-step command prompt,
commands requiring to hold the namespace lock (ex. namespace) cannot be
executed. ACPICA BZ 1362, fixed by Lv Zheng.
Link: https://github.com/acpica/acpica/commit/91af5d18
Link: https://bugs.acpica.org/show_bug.cgi?id=1362
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 1db14dc88f308119634d77ab9dcb6586b9fe4777
On the error return path when acpi_get_object_info fails the allocated
pathname is not free'd leading to a memory leak. Free pathname
to fix this.
Link: https://github.com/acpica/acpica/commit/1db14dc8
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 6b58810b9aad7358fbf1a0f4057fefa8d29838d3
This change fixes two instances where the repair code made an incorrect
assumption about how reference counts are assigned to package objects.
Resolves issues where a warning was issued about a "large reference
count" -- which usually indicates an attempt to delete an object
that has previously been poisoned and released into the object cache.
Link: https://github.com/acpica/acpica/commit/6b58810b
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit a23325b2e583556eae88ed3f764e457786bf4df6
I found some ACPI operand cache leaks in ACPI early abort cases.
Boot log of ACPI operand cache leak is as follows:
>[ 0.174332] ACPI: Added _OSI(Module Device)
>[ 0.175504] ACPI: Added _OSI(Processor Device)
>[ 0.176010] ACPI: Added _OSI(3.0 _SCP Extensions)
>[ 0.177032] ACPI: Added _OSI(Processor Aggregator Device)
>[ 0.178284] ACPI: SCI (IRQ16705) allocation failed
>[ 0.179352] ACPI Exception: AE_NOT_ACQUIRED, Unable to install
System Control Interrupt handler (20160930/evevent-131)
>[ 0.180008] ACPI: Unable to start the ACPI Interpreter
>[ 0.181125] ACPI Error: Could not remove SCI handler
(20160930/evmisc-281)
>[ 0.184068] kmem_cache_destroy Acpi-Operand: Slab cache still has
objects
>[ 0.185358] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.10.0-rc3 #2
>[ 0.186820] Hardware name: innotek gmb_h virtual_box/virtual_box, BIOS
virtual_box 12/01/2006
>[ 0.188000] Call Trace:
>[ 0.188000] ? dump_stack+0x5c/0x7d
>[ 0.188000] ? kmem_cache_destroy+0x224/0x230
>[ 0.188000] ? acpi_sleep_proc_init+0x22/0x22
>[ 0.188000] ? acpi_os_delete_cache+0xa/0xd
>[ 0.188000] ? acpi_ut_delete_caches+0x3f/0x7b
>[ 0.188000] ? acpi_terminate+0x5/0xf
>[ 0.188000] ? acpi_init+0x288/0x32e
>[ 0.188000] ? __class_create+0x4c/0x80
>[ 0.188000] ? video_setup+0x7a/0x7a
>[ 0.188000] ? do_one_initcall+0x4e/0x1b0
>[ 0.188000] ? kernel_init_freeable+0x194/0x21a
>[ 0.188000] ? rest_init+0x80/0x80
>[ 0.188000] ? kernel_init+0xa/0x100
>[ 0.188000] ? ret_from_fork+0x25/0x30
When early abort is occurred due to invalid ACPI information, Linux kernel
terminates ACPI by calling acpi_terminate() function. The function calls
acpi_ns_terminate() function to delete namespace data and ACPI operand cache
(acpi_gbl_module_code_list).
But the deletion code in acpi_ns_terminate() function is wrapped in
ACPI_EXEC_APP definition, therefore the code is only executed when the
definition exists. If the define doesn't exist, ACPI operand cache
(acpi_gbl_module_code_list) is leaked, and stack dump is shown in kernel log.
This causes a security threat because the old kernel (<= 4.9) shows memory
locations of kernel functions in stack dump, therefore kernel ASLR can be
neutralized.
To fix ACPI operand leak for enhancing security, I made a patch which
removes the ACPI_EXEC_APP define in acpi_ns_terminate() function for
executing the deletion code unconditionally.
Link: https://github.com/acpica/acpica/commit/a23325b2
Signed-off-by: Seunghun Han <kkamagui@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 521bedc49b42e59116de1b54dcd95d30d36cac90
Not needed since there is no function tracing for the
validation function in hwvalid.c
Link: https://github.com/acpica/acpica/commit/521bedc4
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 5ecc479f62a57ab1e9d25ec3b0b84682fdf8a543
hwvalid.c - no trace needed for validate I/O function.
Link: https://github.com/acpica/acpica/commit/5ecc479f
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 57c1b2d3e2f9ff7f465b0f08bfb38294101fe0b3
utxferror, update function headers.
Link: https://github.com/acpica/acpica/commit/57c1b2d3
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit ba5020b2dbe1538e4ccd7ac2dfd8843a690c007f
This change enhances the detection of resource descriptors
within a buffer object. For the end_tag opcode, the second byte
is defined to be either a checksum or zero. All known ASL compilers
insert a zero for this byte. The disassembler now ensures this
byte is zero before deciding that a buffer should be disassembled
to a resource descriptor. This helps eliminate incorrect decisions
when attempting to disassemble a buffer to a resource descriptor.
Link: https://github.com/acpica/acpica/commit/ba5020b2
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reading an ACPI table through the /sys/firmware/acpi/tables interface
more than 65,536 times leads to the following log message:
ACPI Error: Table ffff88033595eaa8, Validation count is zero after increment
(20170119/tbutils-423)
...and the table being unavailable until the next reboot. Add the
missing acpi_put_table() so the table ->validation_count is decremented
after each read.
Reported-by: Anush Seetharaman <anush.seetharaman@intel.com>
Fixes: 174cc7187e "ACPICA: Tables: Back port acpi_get_table_with_size() ..."
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: 4.10+ <stable@vger.kernel.org> # 4.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
I2C clock frequency of Designware ip for Hisilicon Hip07 is 200M,
but 250M for Hip08, use two ACPI IDs to differentiate them.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The INT0002 device is necessary to clear wakeup interrupt sources
on Cherry Trail devices, without it we get nobody cared IRQ msgs
and some systems don't properly resume at all without it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Several Bay / Cherry Trail devices (all of which ship with Windows 10) hide
the LPSS PWM controller in ACPI, typically the _STA method looks like this:
Method (_STA, 0, NotSerialized) // _STA: Status
{
If (OSID == One)
{
Return (Zero)
}
Return (0x0F)
}
Where OSID is some dark magic seen in all Cherry Trail ACPI tables making
the machine behave differently depending on which OS it *thinks* it is
booting, this gets set in a number of ways which we cannot control, on
some newer machines it simple hardcoded to "One" aka win10.
This causes the PWM controller to get hidden, which means Linux cannot
control the backlight level on cht based tablets / laptops.
Since loading the driver for this does no harm (the only in kernel user
of it is the i915 driver, which will only uses it when it needs it), this
commit makes acpi_bus_get_status() always set status to ACPI_STA_DEFAULT
for the LPSS PWM device, fixing the lack of backlight control.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[ rjw: Rename the new file to utils.c ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
memcpy_from_pmem() maps directly to memcpy_mcsafe(). The wrapper
serves no real benefit aside from affording a more generic function name
than the x86-specific 'mcsafe'. However this would not be the first time
that x86 terminology leaked into the global namespace. For lack of
better name, just use memcpy_mcsafe() directly.
This conversion also catches a place where we should have been using
plain memcpy, acpi_nfit_blk_single_io().
Cc: <x86@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently SoCs pass2.x do not emulate EA headers for ACPI boot method at
all. However, for pass2.x some devices (like EDAC) advertise incorrect
base addresses in their BARs which results in driver probe failure during
resource request. Since all problematic blocks are on 2nd NUMA node under
domain 10 add necessary quirk entry to obtain BAR addresses correction
using EA header emulation.
Fixes: 44f22bd91e ("PCI: Add MCFG quirks for Cavium ThunderX pass2.x host controller")
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Robert Richter <rrichter@cavium.com>
CC: stable@vger.kernel.org # v4.10+
With no blank lines, it's not obvious where the macro definitions end and
the uses begin. Add some blank lines and reorder the ThunderX definitions.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.10+
The IORT linker section introduced by commit 34ceea275f
("ACPI/IORT: Introduce linker section for IORT entries probing")
was needed to make sure SMMU drivers are registered (and therefore
probed) in the kernel before devices using the SMMU have a chance
to probe in turn.
Through the introduction of deferred IOMMU configuration the linker
section based IORT probing infrastructure is not needed any longer, in
that device/SMMU probe dependencies are managed through the probe
deferral mechanism, making the IORT linker section infrastructure
unused, so that it can be removed.
Remove the unused IORT linker section probing infrastructure
from the kernel to complete the ACPI IORT IOMMU configure probe
deferral mechanism implementation.
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This is an equivalent to the DT's handling of the iommu master's probe
with deferred probing when the corrsponding iommu is not probed yet.
The lack of a registered IOMMU can be caused by the lack of a driver for
the IOMMU, the IOMMU device probe not having been performed yet, having
been deferred, or having failed.
The first case occurs when the firmware describes the bus master and
IOMMU topology correctly but no device driver exists for the IOMMU yet
or the device driver has not been compiled in. Return NULL, the caller
will configure the device without an IOMMU.
The second and third cases are handled by deferring the probe of the bus
master device which will eventually get reprobed after the IOMMU.
The last case is currently handled by deferring the probe of the bus
master device as well. A mechanism to either configure the bus master
device without an IOMMU or to fail the bus master device probe depending
on whether the IOMMU is optional or mandatory would be a good
enhancement.
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
[Lorenzo: Added fixes for dma_coherent_mask overflow, acpi_dma_configure
called multiple times for same device]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Configuring DMA ops at probe time will allow deferring device probe when
the IOMMU isn't available yet. The dma_configure for the device is
now called from the generic device_attach callback just before the
bus/driver probe is called. This way, configuring the DMA ops for the
device would be called at the same place for all bus_types, hence the
deferred probing mechanism should work for all buses as well.
pci_bus_add_devices (platform/amba)(_device_create/driver_register)
| |
pci_bus_add_device (device_add/driver_register)
| |
device_attach device_initial_probe
| |
__device_attach_driver __device_attach_driver
|
driver_probe_device
|
really_probe
|
dma_configure
Similarly on the device/driver_unregister path __device_release_driver is
called which inturn calls dma_deconfigure.
This patch changes the dma ops configuration to probe time for
both OF and ACPI based platform/amba/pci bus devices.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci part)
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The IOMMU probe deferral implementation requires a mechanism to detect
if drivers for SMMU components are built-in in the kernel to detect
whether IOMMU configuration for a given device should be deferred (ie
SMMU drivers present but still not probed) or not (drivers not present).
Add a simple function to IORT to detect if SMMU drivers for SMMU
components managed by IORT are built-in in the kernel.
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Cc: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The intel_pmic_xpower code provides an OPRegion handler, which must be
available before other drivers using it are loaded, which can only be
ensured if both the mfd and opregion drivers are built in, which is why
the Kconfig option for intel_pmic_xpower is a bool.
The use of IIO is causing trouble for generic distro configs here as
distros will typically want to build IIO drivers as modules and there
really is no reason to use IIO here. The reading of the ADC value is a
single regmap_bulk_read, which is already protected against races by
the regmap-lock.
This commit removes the use of IIO, allowing distros to enable the
driver without needing to built IIO in and also actually simplifies
the code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add opregion driver for Intel CHT Whiskey Cove PMIC, based on various
non upstreamed CHT Whiskey Cove PMIC patches. This does not include
support for the Thermal opregion (DPTF) due to lacking documentation.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_bus_attach() does not check the visited flag for devices that
have been enumerated already and some of them may be enumerated
for multiple times as a result, because some callers of
acpi_bus_scan() don't check the visited flag either.
For this reason, modify acpi_bus_attach() to check the visited flag
and avoid enumerating devices that have already been enumerated.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Joey Lee <jlee@suse.com>
The current code in acpi_bus_attach() is inconsistent with respect
to device objects with ACPI drivers bound to them, as it allows
ACPI drivers to bind to device objects with existing "physical"
device companions, but it doesn't allow "physical" device objects
to be created for ACPI device objects with ACPI drivers bound to
them. Thus, in some cases, the outcome depends on the ordering
of events which is confusing at best.
For this reason, modify acpi_bus_attach() to call
acpi_default_enumeration() for device objects with the
pnp.type.platform_id flag set regardless of whether or not
any ACPI drivers are bound to them.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Joey Lee <jlee@suse.com>
On some systems we have a native PMIC driver which provides Mains
monitoring, while the ACPI ac driver is broken on these systems
due to bad DSTDs or because we do not support the proprietary and
undocumented ACPI opregions these ACPI battery devices rely on
(e.g. BMOP opregion).
This leads for example to a ADP1 power_supply which reports
itself as always online even if no mains are connected.
This commit adds a blacklist with PMIC ACPI HIDs for which we've a
native charger or extcon driver and makes the ACPI ac driver not
register itself when a PMIC on this list is present.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On some systems we have a native PMIC driver which provides battery
monitoring, while the ACPI battery driver is broken on these systems
due to bad DSDTs or because we do not support the proprietary and
undocumented ACPI opregions these ACPI battery devices rely on
(e.g. BMOP opregion).
This leads to there being 2 battery power_supply-s registed like this:
~$ acpi
Battery 0: Charging, 84%, 00:49:39 until charged
Battery 1: Unknown, 0%, rate information unavailable
Even if the ACPI battery where to function fine (which on systems
where we have a native PMIC driver it often doesn't) we still do not
want to export the same battery to userspace twice.
This commit adds a blacklist with PMIC ACPI HIDs for which we've a
native battery driver and makes the ACPI battery driver not register
itself when a PMIC on this list is present.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194811
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The acpi_lock_battery_dir() / acpi_bus_register_driver() calls in
acpi_battery_init_async() may fail.
Check that they succeeded before undoing them.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_dev_found just iterates over all ACPI-ids and sees if one matches.
This means that it will return true for devices which are in the DSDT
but disabled (their _STA method returns 0).
For some drivers it is useful to be able to check if a certain HID
is not only present in the namespace, but also actually present as in
acpi_device_is_present() will return true for the device. For example
because if a certain device is present then the driver will want to use
an extcon or IIO ADC channel provided by that device.
This commit adds a new acpi_dev_present helper which drivers can use
to this end.
Like acpi_dev_found, acpi_dev_present take a HID as argument, but
it also has 2 extra optional arguments to only check for an ACPI
device with a specific UID and/or HRV value. This makes it more
generic and allows it to replace custom code doing similar checks
in several places.
Arguably acpi_dev_present is what acpi_dev_found should have been, but
there are too many users to just change acpi_dev_found without the risk
of breaking something.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The comment for acpi_video_bqc_quirk is by Felipe Contreras, taken from
the git history.
Signed-off-by: Dmitry Frank <mail@dmitryfrank.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
gcc -O2 cannot always prove that the loop in acpi_power_get_inferred_state()
is enterered at least once, so it assumes that cur_state might not get
initialized:
drivers/acpi/power.c: In function 'acpi_power_get_inferred_state':
drivers/acpi/power.c:222:9: error: 'cur_state' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This sets the variable to zero at the start of the loop, to ensure that
there is well-defined behavior even for an empty list. This gets rid of
the warning.
The warning first showed up when the -Os flag got removed in a bug fix
patch in linux-4.11-rc5.
I would suggest merging this addon patch on top of that bug fix to avoid
introducing a new warning in the stable kernels.
Fixes: 61b79e16c6 (ACPI: Fix incompatibility with mcount-based function graph tracing)
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This driver adds support for parsing SBSA Generic Watchdog timer
in GTDT, parse all info in SBSA Generic Watchdog Structure in GTDT,
and creating a platform device with that information.
This allows the operating system to obtain device data from the
resource of platform device. The platform device named "sbsa-gwdt"
can be used by the ARM SBSA Generic Watchdog driver.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
On platforms booting with ACPI, architected memory-mapped timers'
configuration data is provided by firmware through the ACPI GTDT
static table.
The clocksource architected timer kernel driver requires a firmware
interface to collect timer configuration and configure its driver.
this infrastructure is present for device tree systems, but it is
missing on systems booting with ACPI.
Implement the kernel infrastructure required to parse the static
ACPI GTDT table so that the architected timer clocksource driver can
make use of it on systems booting with ACPI, therefore enabling
the corresponding timers configuration.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[Mark: restructure error handling]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
This patch adds support for parsing arch timer info in GTDT,
provides some kernel APIs to parse all the PPIs and
always-on info in GTDT and export them.
By this driver, we can simplify arm_arch_timer drivers, and
separate the ACPI GTDT knowledge from it.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
The first two items in the _BCL method response are special:
- Level when machine has full power
- Level when machine is on batteries
- .... actual supported levels go there ....
So this commits adds an enum and uses its descriptive elements
throughout the code, instead of magic numbers.
Signed-off-by: Dmitry Frank <mail@dmitryfrank.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The battery can only be detected after AC power adapter event.
Adding the machine to acpi_rev_dmi_table[] can work around this
issue.
Link: https://bugs.launchpad.net/bugs/1678590
Link: https://bugzilla.kernel.org/show_bug.cgi?id=105721
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Function acpi_parse_entries() is not used any more and if necessary,
acpi_table_parse_entries() can be used instead of it, so drop it.
Signed-off-by: Baoquan He <bhe@redhat.com>
[ rjw: Subject / changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Computed delivered performance using CPPC feedback counters are in the
CPPC abstract scale, whereas cppc_cpufreq driver operates in KHz scale.
Exposing the CPPC performance capabilities (highest,lowest, nominal,
lowest non-linear) will allow userspace to figure out the conversion
factor from CPPC abstract scale to KHz.
Also rename ctr_wrap_time to wraparound_time so that show_cppc_data()
macro will work with it.
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Read lowest non linear perf in cppc_get_perf_caps so that it can be exposed
via sysfs to the usespace. Lowest non linear perf is the lowest performance
level at which nonlinear power savings are achieved.
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The workqueue may still be running when the devres callbacks start
firing to deallocate an acpi_nfit_desc instance. Stop and flush the
workqueue before letting any other devres de-allocations proceed.
Reported-by: Linda Knippers <linda.knippers@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The optional _PXM method evaluates to an integer that identifies the
proximity domain of a device object. On ACPI based kernel boot, the
field numa_node in 'struct device' is always set to -1 irrespective
of _PXM value that is specified in the ACPI device object. But in
case of device-tree based kernel boot the numa_node field is populated
and reflects to a DT property that is specified in DTS according to
the below document.
https://www.kernel.org/doc/Documentation/devicetree/bindings/numa.txthttp://lxr.free-electrons.com/source/drivers/of/device.c#L54
Without this patch dev_to_node() always returns -1 for all platform
devices. This patch adds support for the ACPI _PXM method and updates
the platform device NUMA node id using acpi_get_node() which provides
the PXM-to-NUMA mapping information.
The individual platform device drivers should be able to use the
NUMA-aware memory allocation functions kmalloc_node() and
alloc_pages_node() to improve performance.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Jiandi An <anjiandi@codeaurora.org>
[ rjw: Subject / changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When maxcpus=X kernel argument is used, we parse the ACPI tables only
for the first X cpus. The per-cpu ACPI data include the _PSD tables
which gives information about related cpus.
cppc_cpufreq and acpi-cpufreq parses the table once during init to
deduce the related cpus. If a user brings a new cpu online after boot
the related cpu data becomes incorrect.
acpi_get_psd_map() in acpi_cppc.c returns error if it fails to find
the parsed ACPI data for possible CPU resulting in cppc_cpufreq
initialization failure.
With this change we will probe all possible CPUs prior to cpufreq
initialization, but will bring only setup_max_cpus online. nr_cpus
kernel parameter can be used to restict even parsing per-cpu ACPI
tables.
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The nvdimm probe flushing mechanism gives userspace a sync point where
it knows all asynchronous driver probe sequences have completed.
However, it need not wait for other asynchronous actions, like
on-demand address-range-scrub. Track the init work separately from other
work in the workqueue, and only flush the former.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Be tolerant of cases where the BIOS provided NFIT does not consistently
set the flags in all NVDIMM Region Mapping structures associated with a
given dimm.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Stop requiring dimms be successfully mapped into a
system-physical-address range. For provisioning and hardware remediation
purposes the kernel should account for failed devices in sysfs. If
possible it should still allow management commands to be sent to the
device.
Reported-by: Toshi Kani <toshi.kani@hpe.com>
Tested-by: Toshi Kani <toshi.kani@hpe.com>
Reported-by: Linda Knippers <linda.knippers@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Pull nvdimm fixes from Dan Williams:
"A small crop of lockdep, sleeping while atomic, and other fixes /
band-aids in advance of the full-blown reworks targeting the next
merge window. The largest change here is "libnvdimm: fix blk free
space accounting" which deletes a pile of buggy code that better
testing would have caught before merging. The next change that is
borderline too big for a late rc is switching the device-dax locking
from rcu to srcu, I couldn't think of a smaller way to make that fix.
The __copy_user_nocache fix will have a full replacement in 4.12 to
move those pmem special case considerations into the pmem driver. The
"libnvdimm: band aid btt vs clear poison locking" commit admits that
our error clearing support for btt went in broken, so we just disable
it in 4.11 and -stable. A replacement / full fix is in the pipeline
for 4.12
Some of these would have been caught earlier had DEBUG_ATOMIC_SLEEP
been enabled on my development station. I wonder if we should have:
config DEBUG_ATOMIC_SLEEP
default PROVE_LOCKING
...since I mistakenly thought I got both with PROVE_LOCKING=y.
These have received a build success notification from the 0day robot,
and some have appeared in a -next release with no reported issues"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
x86, pmem: fix broken __copy_user_nocache cache-bypass assumptions
device-dax: switch to srcu, fix rcu_read_lock() vs pte allocation
libnvdimm: band aid btt vs clear poison locking
libnvdimm: fix reconfig_mutex, mmap_sem, and jbd2_handle lockdep splat
libnvdimm: fix blk free space accounting
acpi, nfit, libnvdimm: fix interleave set cookie calculation (64-bit comparison)
acpi_processor_get_throttling() requires to invoke the getter function on
the target CPU. This is achieved by temporarily setting the affinity of the
calling user space thread to the requested CPU and reset it to the original
affinity afterwards.
That's racy vs. CPU hotplug and concurrent affinity settings for that
thread resulting in code executing on the wrong CPU and overwriting the
new affinity setting.
acpi_processor_get_throttling() is invoked in two ways:
1) The CPU online callback, which is already running on the target CPU and
obviously protected against hotplug and not affected by affinity
settings.
2) The ACPI driver probe function, which is not protected against hotplug
during modprobe.
Switch it over to work_on_cpu() and protect the probe function against CPU
hotplug.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: linux-acpi@vger.kernel.org
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/20170412201042.785920903@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When acpi_install_notify_handler() fails the cooling device stays
registered and the sysfs files created via acpi_pss_perf_init() are
leaked and the function returns success.
Undo acpi_pss_perf_init() and return a proper error code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: linux-acpi@vger.kernel.org
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/20170412201042.695499645@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add support for the ACPI_NFIT_MEM_MAP_FAILED ("map_fail") and
ACPI_NFIT_MEM_HEALTH_ENABLED ("smart_notify") health state flags. The
"map_fail" flag identifies DIMMs that were not mapped into one or more
physical address ranges. The "health_notify" flag indicates whether
platform firmware will send notifications when there is new SMART health
data to consume.
Acked-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* acpi-scan-fixes:
ACPI / scan: Set the visited flag for all enumerated devices
* acpica-fixes:
Revert "ACPICA: Resources: Not a valid resource if buffer length too long"
Revert commit 57707a9a77 (ACPICA: Resources: Not a valid resource if
buffer length too long) as it is reported to prevent the TPM module
from loading on Lenovo X60 with Coreboot.
It also causes new confusing warnings to show up in the kernel log.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195311
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Calls to acpi_get_table() must be paired with acpi_put_table() to undo
the mapping established by acpi_tb_acquire_table().
It turns out this has no effect in practice since the NFIT will already
be mapped to support the /sys/firmware/acpi/tables/NFIT attribute in
sysfs.
Fixes: 6b11d1d677 ("ACPI / osl: Remove acpi_get_table_with_size()/early_acpi_os_unmap_memory() users")
Cc: Lv Zheng <lv.zheng@intel.com>
Reported-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The newline in MODULE_PARM_DESC causes modinfo to print the parameter
data type on a separate line, which is different from all the other
module parameters and could potentially cause a problem for someone
parsing the output of modinfo.
Signed-off-by: Linda Knippers <linda.knippers@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Provide the ability to request a default DSM family. If it is not
supported, then fall back to the normal discovery order.
This is helpful for testing platforms that support multiple DSM
families. It will also allow administrators to request the DSM family
that their management tools support, which may not be the first one
found using the current discovery order.
Signed-off-by: Linda Knippers <linda.knippers@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
As it is today, we can't enable or test new NVDIMM management functions
provided by new firmware and tools without changing the kernel. We also
can't prevent documented DSM functions from being called in the case of
buggy firmware. This patch provides a module parameter that overrides
the DSM function mask that is built into the kernel.
If the "disable_vendor_specific" module parameter is also used we ignore
the new parameter.
Signed-off-by: Linda Knippers <linda.knippers@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Commit 10c7e20b2f (ACPI / scan: fix enumeration (visited) flags for
bus rescans) attempted to fix a problem with ACPI-based enumerateion
of I2C/SPI devices, but it forgot to ensure that the visited flag
will be set for all of the other enumerated devices, so fix that.
Fixes: 10c7e20b2f (ACPI / scan: fix enumeration (visited) flags for bus rescans)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194885
Reported-and-tested-by: Kevin Locke <kevin@kevinlocke.name>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: 4.8+ <stable@vger.kernel.org> # 4.8+
/sys/firmware/acpi/hotplug/force_remove was presumably added to support
auto offlining in the past. This is, however, inherently dangerous for
some hotplugable resources like memory. The memory offlining fails when
the memory is still in use and cannot be dropped or migrated. If we
ignore the failure we are basically allowing for subtle memory
corruption or a crash.
We have actually noticed the later while hitting BUG() during the memory
hotremove (remove_memory):
ret = walk_memory_range(PFN_DOWN(start), PFN_UP(start + size - 1), NULL,
check_memblock_offlined_cb);
if (ret)
BUG();
it took us quite non-trivial time realize that the customer had
force_remove enabled. Even if the BUG was removed here and we could
propagate the error up the call chain it wouldn't help at all because
then we would hit a crash or a memory corruption later and harder to
debug. So force_remove is unfixable for the memory hotremove. We haven't
checked other hotplugable resources to be prone to a similar problems.
Remove the force_remove functionality because it is not fixable currently.
Keep the sysfs file and report an error if somebody tries to enable it.
Encourage users to report about the missing functionality and work with
them with an alternative solution.
Reviewed-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
_LINUX: used to detect a target build is a linux kernel/application.
__linux__: used to detect a build is on a linux hosts.
Thus we can see: if a linux kernel build is performed on environments other
than linux hosts, __linux__ may not be defined by the compiler and _LINUX
cannot cover linux kernel resident ACPICA files, as it's only defined in
<linux/acpi.h> and hence only allows non ACPICA kernel files to correctly
include aclinux.h.
As a conclusion, we don't actually support such build.
This patch adds -D_LINUX for ACPICA files so that kernel builds on any
hosts can use unified _LINUX as a linux kernel target indication to
correctly include aclinux.h.
Tested-by: Al Stone <ahs3@redhat.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The E820 rework in WIP.x86/boot has gone through a couple of weeks
of exposure in -tip, merge it in a wider fashion.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Move all the EDAC core functionality behind CONFIG_EDAC and get rid of
that indirection. Update defconfigs which had it.
While at it, fix dependencies such that EDAC depends on RAS for the
tracepoints.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: linux-edac@vger.kernel.org
Getting timeout message from BMC when trying to read from a non-existent
FRU. This is expected but warning is not.
Let's reduce the warning to debug.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
ACPI_IPMI driver currently depends on IPMI System Interface (IPMI_SI)
driver to be enabled. IPMI_SI driver only handles KCS, SMIC and BT BMC
interfaces.
IPMI_SSIF is an alternative BMC communication method. It allows BMC to
be accessed over an I2C bus instead of a standard interface.
Change the dependency to IPMI_HANDLER so that ACPI_IPMI works with all
IPMI providers.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Now that the ACPI BGRT handling code has been made generic, we can
enable it for arm64.
Signed-off-by: Bhupesh Sharma <bhsharma@redhat.com>
[ Updated commit log to reflect that BGRT is only enabled for arm64, and added
missing 'return' statement to the dummy acpi_parse_bgrt() function. ]
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20170404160245.27812-8-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit c2a6bbaf0c (ACPI / scan: Prefer devices without _HID/_CID
for _ADR matching) added a list_empty(&adev->pnp.ids) check to
find_child_checks() so as to catch situations in which the ACPI
core attempts to decode _ADR for a device having a _HID too which
is strictly against the spec. However, it overlooked the fact that
the adev->pnp.ids list for the devices taken into account by
find_child_checks() may contain device IDs set internally by the
kernel, like "LNXVIDEO" (thanks to Zhang Rui for that realization),
and it broke the enumeration of those devices as a result.
To unbreak it, replace the overly coarse grained list_empty()
check with a much more precise check against the pnp.type.platform_id
flag which is only set for devices having a _HID (that's how it
should be done from the start, as having both _ADR and _CID is
actually permitted).
Fixes: c2a6bbaf0c (ACPI / scan: Prefer devices without _HID/_CID for _ADR matching)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194889
Reported-and-tested-by: Mike <mike@mikewilson.me.uk>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Cc: 4.10+ <stable@vger.kernel.org> # 4.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-hotplug-fixes:
ACPI: Do not create a platform_device for IOAPIC/IOxAPIC
ACPI: ioapic: Clear on-stack resource before using it
* acpi-build-fixes:
ACPI: Fix incompatibility with mcount-based function graph tracing
* acpi-apei-fixes:
ACPI / APEI: Add missing synchronize_rcu() on NOTIFY_SCI removal
By allowing platform MSI domain to be created on ACPI platforms,
a platform device MSI domain can be set-up when it is probed.
In order to do that, the MSI domain the platform device connects
to should be retrieved, so the iort_get_platform_device_domain() is
introduced to retrieve the domain from the IORT kernel layer.
With the domain retrieved, we need a proper way to set the
domain to platform device.
Given that some platform devices (irqchips) require the MSI irqdomain
to be their interrupt parent domain, the MSI irqdomain should be
determined before platform device is probed but after the platform
device is allocated which means that the code setting up the MSI
irqdomain, ie acpi_configure_pmsi_domain() should be called in
acpi_platform_notify() (that is triggered after adding a device but
before the respective driver is probed) for the platform MSI domain
code set-up path to work properly.
Acked-by: Rafael J. Wysocki <rafael@kernel.org> [for glue.c]
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[lorenzo.pieralisi@arm.com: rewrote commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Tomasz Nowicki <tn@semihalf.com>
For devices connecting to an ITS, the devices need to identify themself
through a devid; this devid is represented in the IORT table in named
component node [1] for platform devices, so this patch adds code that
scans the IORT table to retrieve the devices devid.
Add an IORT interface to collect ITS devices devid to carry out platform
devices MSI mappings with IORT tables.
[1]: https://static.docs.arm.com/den0049/b/DEN0049B_IO_Remapping_Table.pdf
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[lorenzo.pieralisi@arm.com: rewrote commit log/dropped ITS changes]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
To retrieve dev id for IORT named components nodes there are
two steps involved (second is optional):
(1) Retrieve the initial id (this may well provide the final mapping)
(2) Map the id (optional if (1) represents the map type we need), this
is needed for use cases such as NC (named component) -> SMMU -> ITS
mappings.
the iort_node_get_id() function was created for step (1) above and
iort_node_map_rid() for step (2).
Create a wrapper, named iort_node_map_platform_id(), that encompasses
the two steps at once to retrieve the dev id to provide steps (1)-(2)
functionality.
iort_node_map_platform_id() will handle the parent type so type handling
in iort_node_get_id() is duplicated, remove it and update current
iort_node_get_id() users to move them over to iort_node_map_platform_id().
Suggested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Suggested-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
[lorenzo.pieralisi@arm.com: rewrote commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Tomasz Nowicki <tn@semihalf.com>
iort_node_map_rid() was designed to take an input id (that is not
necessarily a PCI requester id) and map it to an output id (eg an SMMU
streamid or an ITS deviceid) according to the mappings provided by an
IORT node mapping entries. This means that the iort_node_map_rid() input
id is not always a PCI requester id as its name, parameters and local
variables suggest, which is misleading.
Apply the s/rid/id substitution to the iort_node_map_rid() mapping
function and its users to make sure its intended usage is clearer.
Suggested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Tomasz Nowicki <tn@semihalf.com>
Functionally fwnode_property_read_string_array() should match
of_property_read_string_array() and work as a drop-in substitute for the
latter. of_property_read_string_array() returns the number of strings read
if the target string pointer array is non-NULL. Make
fwnode_property_read_string_array() do the same.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
DT has had concept of remote endpoints for some time already. It makes
possible to reference another firmware node through a property called
remote-endpoint. This is already used by some subsystems like v4l2 for
parsing hardware properties related to camera.
This patch adds ACPI support for remote endpoints utilizing _DSD
hierarchical data extensions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI _DSD hierarchical data extension makes it possible to have
hierarchies deeper than one level in similar way than DT allows. These
"subsubnodes" have not been accessible because device property
implementation only provides device_get_next_child_node() that is limited
to direct descendants of a device.
We need this ability in order support things like remote endpoints
currently supported in DT with of_graph_* APIs.
Modify acpi_get_next_subnode() to accept fwnode handle instead and update
callers accordingly. Also add a new function fwnode_get_next_child_node()
that works directly with fwnodes and modify device_get_next_child_node() to
call it directly. While there add a macro fwnode_for_each_child_node()
analogous to the current device_for_each_child_node() but it works with
fwnodes instead of devices.
Link: http://www.uefi.org/sites/default/files/resources/_DSD-hierarchical-data-extension-UUID-v1.pdf
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sometimes it is useful to be able to navigate firmware node hierarchy
upwards toward parent nodes. ACPI device nodes are pretty much already
supported because ACPICA provides acpi_get_parent(). ACPI data nodes,
however, are all below the same parent ACPI device. Their hierarchy is
created by "linking" each other using references in the value field.
Add parent pointer to the parent data node while we create them so it is
easy to navigate the hierarchy backwards. We use this parent pointer in a
new function acpi_node_get_parent() that is able to extract parent of both
ACPI firmware node types.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Paul Menzel reported a warning:
WARNING: CPU: 0 PID: 774 at /build/linux-ROBWaj/linux-4.9.13/kernel/trace/trace_functions_graph.c:233 ftrace_return_to_handler+0x1aa/0x1e0
Bad frame pointer: expected f6919d98, received f6919db0
from func acpi_pm_device_sleep_wake return to c43b6f9d
The warning means that function graph tracing is broken for the
acpi_pm_device_sleep_wake() function. That's because the ACPI Makefile
unconditionally sets the '-Os' gcc flag to optimize for size. That's an
issue because mcount-based function graph tracing is incompatible with
'-Os' on x86, thanks to the following gcc bug:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=42109
I have another patch pending which will ensure that mcount-based
function graph tracing is never used with CONFIG_CC_OPTIMIZE_FOR_SIZE on
x86.
But this patch is needed in addition to that one because the ACPI
Makefile overrides that config option for no apparent reason. It has
had this flag since the beginning of git history, and there's no related
comment, so I don't know why it's there. As far as I can tell, there's
no reason for it to be there. The appropriate behavior is for it to
honor CONFIG_CC_OPTIMIZE_FOR_{SIZE,PERFORMANCE} like the rest of the
kernel.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: All applicable <stable@vger.kernel.org>
When removing a GHES device notified by SCI, list_del_rcu() is used,
ghes_remove() should call synchronize_rcu() before it goes on to call
kfree(ghes), otherwise concurrent RCU readers may still hold this list
entry after it has been freed.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: "Huang, Ying" <ying.huang@intel.com>
Fixes: 81e88fdc43 (ACPI, APEI, Generic Hardware Error Source POLL/IRQ/NMI notification type support)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
No platform-device is required for IO(x)APICs, so don't even
create them.
[ rjw: This fixes a problem with leaking platform device objects
after IOAPIC/IOxAPIC hot-removal events.]
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The on-stack resource-window 'win' in setup_res() is not
properly initialized. This causes the pointers in the
embedded 'struct resource' to contain stale addresses.
These pointers (in my case the ->child pointer) later get
propagated to the global iomem_resources list, causing a #GP
exception when the list is traversed in
iomem_map_sanity_check().
Fixes: c183619b63 (x86/irq, ACPI: Implement ACPI driver to support IOAPIC hotplug)
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
While reviewing the -stable patch for commit 86ef58a4e3 "nfit,
libnvdimm: fix interleave set cookie calculation" Ben noted:
"This is returning an int, thus it's effectively doing a 32-bit
comparison and not the 64-bit comparison you say is needed."
Update the compare operation to be immune to this integer demotion problem.
Cc: <stable@vger.kernel.org>
Cc: Nicholas Moulin <nicholas.w.moulin@linux.intel.com>
Fixes: 86ef58a4e3 ("nfit, libnvdimm: fix interleave set cookie calculation")
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Linus Torvalds