Enable the audio codec and the audio dai for the sun8i A33 sinlinx board.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Previously, the Sinlinx SinA33 used everything declared in AXP221 DTSI
while it has an AXP223 PMIC.
This corrects that so the Sinlinx SinA33 can get some features the
AXP223 has (at the moment, ability to have 100mA as maximal current on
VBUS power supply).
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we can handle the generic pinctrl bindings, convert our DT to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The allwinner,drive property set to 10mA was really considered as our
default. Remove all those properties entirely to make that obvious.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The micro-USB on the SinA33 has a somewhat interesting design in the sense
that it has a micro USB connector, but the VBUS is (supposed to be)
controlled through an (unpopulated) jumper.
Obviously, that doesn't work really well, and only the peripheral mode
really works. Still enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This board has a X-Powers AXP223 PMIC connected via RSB. Its regulators
provide power to various parts of the SoC and the board.
Also update the regulator supply phandles.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
mmc2 has a special pin for eMMC hardware reset, which is controllable
from the controller. Add the "mmc-cap-hw-reset" property to denote that
this controller supports this function, and the pins are actually used.
Also increase the signal drive strength for mmc2 pins, for HS-DDR mode
support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Reduced Serial Bus controller is used to talk to the onboard PMIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Sina33 SDK board exposes the EHCI/OHCI USB host pair.
VBUS for this port is always on and non-controllable.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The SinA33 is a core/SDK development board by Sinlinx. The core board
does not have any connectors or pads, other than the pads used to connect
it to the SDK board.
The core board only has the A33 SoC, 2 RAM chips, an eMMC flash chip,
the AXP223 PMIC, and supporting discrete components. eMMC is optional.
The SDK board has a USB host, USB OTG, volume control and home buttons,
audio input/output jacks, a micro-SD slot, camera and SDIO expansion
headers, an LCD connector, and a GPIO expansion header, which has
UARTs, MIPI DSI and I2C available. Only UART0 is enabled though.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
