commit 0d8e2d0dad (OMAP2+: PM/serial:
hold console semaphore while OMAP UARTs are disabled) added use of the
console semaphore to protect UARTs from being accessed after disabled
during idle, but this causes problems in suspend.
During suspend, the console semaphore is acquired by the console
suspend method (console_suspend()) so the try_acquire_console_sem()
will always fail and suspend will be aborted.
To fix, introduce a check so the console semaphore is only attempted
during idle, and not during suspend. Also use the same check so that
the console semaphore is not prematurely released during resume.
Thanks to Paul Walmsley for suggesting adding the same check during
resume.
Cc: Paul Walmsley <paul@pwsan.com>
Tested-by: Jean Pihet <j-pihet@ti.com>
Tested-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The console semaphore must be held while the OMAP UART devices are
disabled, lest a console write cause an ARM abort (and a kernel crash)
when the underlying console device is inaccessible. These crashes
only occur when the console is on one of the OMAP internal serial
ports.
While this problem has been latent in the PM idle loop for some time,
the crash was not triggerable with an unmodified kernel until commit
6f251e9db1 ("OMAP: UART: omap_device
conversions, remove implicit 8520 assumptions"). After this patch, a
console write often occurs after the console UART has been disabled in
the idle loop, crashing the system. Several users have encountered
this bug:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg38396.htmlhttp://www.mail-archive.com/linux-omap@vger.kernel.org/msg36602.html
The same commit also introduced new code that disabled the UARTs
during init, in omap_serial_init_port(). The kernel will also crash
in this code when earlyconsole and extra debugging is enabled:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg36411.html
The minimal fix for the -rc series is to hold the console semaphore
while the OMAP UARTs are disabled. This is a somewhat overbroad fix,
since the console may not be located on an OMAP UART, as is the case
with the GPMC UART on Zoom3. While it is technically possible to
determine which devices the console or earlyconsole is actually
running on, it is not a trivial problem to solve, and the code to do
so is not really appropriate for the -rc series.
The right long-term fix is to ensure that no code outside of the OMAP
serial driver can disable an OMAP UART. As I understand it, code to
implement this is under development by TI.
This patch is a collaboration between Paul Walmsley <paul@pwsan.com>
and Tony Lindgren <tony@atomide.com>. Thanks to Ming Lei
<tom.leiming@gmail.com> and Pramod <pramod.gurav@ti.com> for their
feedback on earlier versions of this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Pramod <pramod.gurav@ti.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jean Pihet <jean.pihet@newoldbits.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
While at it, fix two checkpatch errors.
Several non-const struct instances constified by this patch were added after
the introduction of platform_suspend_ops in checkpatch.pl's list of "should
be const" structs (79404849e9).
Patch against mainline.
Inspired by hunks of the grsecurity patch, updated for newer kernels.
Signed-off-by: Lionel Debroux <lionel_debroux@yahoo.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 914bab936fe0388a529079679e2f137aa4ff548d (OMAP: mach-omap2: Fix
incorrect assignment warnings) changed a pointer from 'u32 *' to
'void *' without also fixing up the pointer arithmetic.
Fix the scratchpad offsets so they are byte offsets instead of
word offsets and thus work correctly with a void pointer base.
Special thanks to Jean Pihet for taking the time track down this
problem and propose an initial solution.
Tested with off-idle and off-suspend on 36xx/Zoom3 and 34xx/omap3evm.
Cc: Manjunath Kondaiah G <manjugk@ti.com>
Reported-by: Jean Pihet <jean.pihet@newoldbits.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Jean Pihet <jean.pihet@newoldbits.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Only OMAP2+ platforms have the System Control Module (SCM) IP block.
In the past, we've kept the SCM header file in plat-omap. This has
led to abuse - device drivers including it; includes being added that
create implicit dependencies on OMAP2+ builds; etc.
In response, move the SCM headers into mach-omap2/.
As part of this, remove the direct SCM access from the OMAP UDC
driver. It was clearly broken. The UDC code needs an indepth review for
use on OMAP2+ chips.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Add prepare idle and resume idle call for uart4 used by 3630.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
To standarize among other uarts (1 to 3), we shall now:
- Enable uart4 autodile bit.
- Enable uart4 wakeup in PER.
- Allow uart4 to wakeup the MPU.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
When the clockdomain layer initializes, place all clockdomains into
software-supervised mode, and clear all wakeup and sleep dependencies
immediately, rather than waiting for the PM code to do this later.
This fixes a major bug where critical sleep dependencies added by the
hwmod code are cleared during late PM init.
As a side benefit, the _init_{wk,sleep}dep_usecount() functions are no
longer needed, so remove them.
Kevin Hilman <khilman@deeprootsystems.com> did all the really hard work on
this, identifying the problem and finding the bug.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The set_pwrdm_state() is needed on omap4 as well so move
this routine to common pm.c file so that it's available for omap3/4
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch moves omap2_pm_wakeup_on_timer() and pm debug entries
form pm34xx.c to pm-debug.c and export it, so that it is available
to other OMAPs
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
In an effort to simplify the core idle path, move any device-specific
special case handling from the core PM idle path into the CPUidle
pre-idle checking path.
This keeps the core, interrupts-disabled idle path streamlined and
independent of any device-specific handling, and also allows CPUidle
to do the checking only for certain C-states as needed. This patch
has the device checks in place for all states with the CHECK_BM flag,
namely all states >= C2.
This patch was inspired by a similar patch written by Tero Kristo as
part of a larger series to add INACTIVE state support.
NOTE: This is a baby-step towards decoupling device idle (or system
idle) from CPU idle. Eventually, CPUidle should only manage the CPU,
and device/system idle should be managed elsewhere.
Cc: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch removes omap3 hardcodings from pm-debug.c
so that enabling PM debugfs support does break compilation
for other OMAP's. This is a preparatory patch for supporting
OMAP4 pm entries through PM debugfs.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cleanup indentation around IO wakeup enable, the '\' terminator is
not required in C when wrapping an expression past end-of-line.
Whitespace change only.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Commit 5a5f561 (convert OMAP3 PRCM macros to the _SHIFT/_MASK suffixes)
mistakenly removed the check for PER when disabling the IO chain.
During idle, if the PER powerdomain transitions into a lower state
and CORE does not, the IO pad wakeups are not being disabled in
the idle path after they are enabled. This can happen with the
lower C-states when using CPUidle for example.
This patch ensures that the check for disabling IO wakeups also checks
for PER transitions, matching the check done to enable IO wakeups.
Found when debugging PM/CPUidle related problems reported by Ameya
Palande <ameya.palande@nokia.com>. Problems were triggered
particularily on boards with UART2 consoles (n900, Overo) since UART2
is in the PER powerdomain.
Tested on l-o master (omap3_defonfig + CONFIG_CPU_IDLE=y) as well
as with current PM branch. Boards tested: n900, Overo, omap3evm.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Ameya Palande <ameya.palande@nokia.com>
Tested-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated description to clarify the transistion]
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM3505/3517 doesn't have IO wakeup capability, so we do not need to set
the bit OMAP3430_EN_IO and the bit OMAP3430_EN_IO_CHAIN in the register
PM_WKEN_WKUP when the system enters suspend state.
Tested on AM3517EVM and OMAP3530EVM.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Checking to se if the IO daisy chain is enabled should be checking the
PM_WKEN register, not the PM_WKST register. Reading PM_WKST tells us
if an event occurred, not whether or not it is enabled.
Apparently, we've been lucky until now in that a pending event has not
been there during enable. However, on 3630/Zoom3, I noticed because
of the WARN that this timeout was always happening.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Writes to the PM_*GRPSEL registers should use _GRPSEL_ macros, not _EN_ macros,
to match the TRM and guard against inadvertent error. This patch should
not cause any functional change.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jouni Högander <jouni.hogander@nokia.com>
Fix all of the remaining PRCM register shift/bitmask macros that did not
use the _SHIFT/_MASK suffixes to use them. This makes the use of these
macros consistent. It is intended to reduce error, as code can be inspected
visually by reviewers to ensure that bitshifts and bitmasks are used in
the appropriate places.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Fix all of the remaining OMAP3 PRCM register shift/bitmask macros that
did not use the _SHIFT/_MASK suffixes to use them. This makes the use
of these macros consistent. It is intended to reduce error, as code
can be inspected visually by reviewers to ensure that bitshifts and
bitmasks are used in the appropriate places.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Currently, the GPIO 'prepare' hook is only called when going to
off-mode, while the function is called 'prepare_for_retention.' This
patch renames the function to 'prepare_for_idle' and calls it for any
powersate != PWRDM_POWER_ON passing in the powerstate.
The hook itself is then responsible for doing various preparation
based on the powerstate.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Off mode is now using the omap2 retention fix code for scanning GPIOs
during off-mode transitions. All the *non_wakeup_gpios variables
are now used for off-mode transition tracking on OMAP3. This patch fixes
cases where GPIO state changes are missed during off-mode.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
We can remove this wakeup dependency since now, when
GPIO2-6 are enabled for IO-pad wakeup, PER domain is gauranteed
to be awake or be woken up to service.
The previous dependency did not handle all corner cases. Since there
was no sleep dependency between CORE and PER domains, if PER enters
RET and CORE is ON, PER will not be active for GPIO handling.
Signed-off-by: Mike Chan <mike@android.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
IO events can also come from GPIO modules, which reside in the PER domain.
It is possible for the PER to enter RET while CORE is still in ON.
If GPIO 2-6 are enabled for IO-pad wakeups, the PER domain will not
wakeup in this case, unless we enable it.
Signed-off-by: Mike Chan <mike@android.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Millisecond resolution is possible and there are use cases for it
(automatic testing).
Seconds-based interface is preserved for compatibility.
Signed-off-by: Ari Kauppi <Ext-Ari.Kauppi@nokia.com>
Reviewed-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
While handling PRCM IRQs, mask out interrupts that are not enabled in
PRM_IRQENABLE_MPU. If these are not masked out, non-enabled
interrupts are caught, a WARN() is printed due to no 'handler' and the
events are cleared. In addition to being noisy, this can also
interfere with independent polling of this register by SR/VP code.
This was noticed using SmartReflex transitions which cause the VPx_*
interrupts to be handled since they are set in PRM_IRQSTATUS_MPU even
but not enabled in PRM_IRQENABLE_MPU.
Acked-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Add _MASK suffix to CM_FCLKEN_IVA2 bitfieds to conform with the rest
of the usage in cm-regbits-34xx.h of using _SHIFT and _MASK suffixes.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
When 'enable_off_mode' is 0, the target power state for MPU
and CORE was locally changed to PWRDM_POWER_RET but, the
statistics are updated for idle state originally selected
by the governor.
This patch 'invalidates' the idle states that lead either of
MPU or Core to PWRDM_POWER_OFF state when 'enable_off_mode'
is '0'. The states are valid once 'enable_off_mode' is set
to '1'.
Added function next_valid_state() to check if current state
is valid; else get the next valid state. It is called from
omap3_enter_idle_bm().
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add usecounting for wakeup and sleep dependencies. In the current
situation, if several functions add dependencies on the same
clockdomains, when the first dependency removal function is called,
the dependency will be incorrectly removed from the hardware.
Add clkdm_clear_all_wkdeps() and clkdm_clear_all_sleepdeps(), which
provide a fast and usecounting-consistent way to clear all hardware
clockdomain dependencies, since accesses to these registers can be
quite slow. pm{2,3}4xx.c has been updated to use these new functions.
The original version of this patch did not touch these files, which
previously wrote directly to the wkdep registers, and thus confused
the usecounting code. This problem was found by Kevin Hilman
<khilman@deeprootsystems.com>.
N.B.: This patch introduces one significant functional difference over
the previous pm34xx.c code: sleepdeps are now cleared during
clockdomain initialization, whereas previously they were left
untouched. This has been tested by Kevin and confirmed to work.
The original version of this patch also did not take into
consideration that some clockdomains do not have sleep or wakeup
dependency sources, which caused NULL pointer dereferences. This
problem was debugged and fixed by Kevin Hilman
<khilman@deeprootsystems.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jouni Högander <jouni.hogander@nokia.com>
Move clockdomain wakeup dependency and sleep dependency data
structures from the powerdomain layer to the clockdomain layer, where
they belong. These dependencies were originally placed in the
powerdomain layer due to unclear documentation; however, it is clear
now that these dependencies are between clockdomains. For OMAP2/3,
this is not such a big problem, but for OMAP4 this needs to be fixed.
Thanks to Benoît Cousson <b-cousson@ti.com> for his advice on this
patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Module offsets were same for OMAP2 and OMAP3 while they differ for OMAP4.
Hence we need different macros for identifying platform specific offsets.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Currently, DSS does not wakeup when there is a DMA request. DSS wake
up event must be enabled so that the DMA request to refill the FIFO
will wake up the CORE domain.
Signed-off-by: Subramani Venkatesh <subramani.venkatesh@windriver.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Due to OMAP3 erratas 1.157, 1.185 the save of the last pad register
(ETK_D14 and ETK_D15) can fail sometimes when there is simultaneous
OCP access to the SCM register area. Fixed by writing the last
register to the save area.
Also, optimized the delay loop for the HW save to include an udelay(1),
which limits the number of unnecessary HW accesses to SCM register area
during the save.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Wake-up from McBSP ports are needed, especially when the THRESHOLD
dma mode is in use for audio playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch removes code blocks that are repeated
in function prcm_setup_regs().
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP interrupt controller goes to unknown state when there is right
combination of l3,l4 sleep/wake-up transitions, l4 autoidle in
interrupt controller and some interrupt. When this happens, interrupts
are not delivered to ARM anymore and ARM will remain in WFI (wait for
interrupt) until interrupt controller is forced to wake-up
(i.e. lauterbach).
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Enable the auto-idle feature of the SCM block to save some additional
power.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Suspending drivers may still generate interrupts just before their suspend is
completed. Any pending interrupts here will prevent sleep.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
`!' has a higher precedence than `&' so parentheses are required.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes a bug where scheduling is delayed until next wakeup due to race
condition (e.g. interrupt requests scheduling just before omap_sram_idle
is entered.)
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch removes the check to see if some functional clocks are
still enabled before entering sleep. This is no longer needed when
using safe state (C1) that keeps CORE active.
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
It is more efficient to use pwrdm_set_next_pwrst for mpu, core and neon
instead of set_pwrdm_state in idle loop. It is anyway known that those are
active in idle loop. So no need to use set_pwrdm_state.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Previously omap3_idle_init() was called in device_init, while
omap_pm_init() is called at late_initcall. This causes the cpu idle
driver to call omap_sram_idle before it is properly initialized. This
patch fixes the issue by moving omap3_idle_init into omap3_pm_init.
Signed-off-by: Kalle Jokiniemi <ext-kalle.jokiniemi@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds support and enables state C4(MPU RET + CORE RET)
and MPU OFF states (C3 and C5.)
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Basic CPUidle driver for OMAP3 with deepest sleep state supported
being MPU CSWR.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Due to an OMAP3 errata (1.142), on HS/EMU devices SDRC should be
programed to issue automatic self refresh on timeout
of AUTO_CNT = 1 prior to any transition to OFF mode.
This is needed only on sil rev's ES3.0 and above.
This patch enables the above needed WA in the SDRC power register
value stored in scratchpad, so that ROM code restores this value
in SDRC POWER on the wakeup path.
The original SDRC POWER register value is stored and restored back
in omap_sram_idle() function.
This fixes some random crashes observed while stressing suspend
on HS/EMU devices.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP 3430 ES3.1 chips have a separate bit for IO daisy-chain
wake up enabling. It needs to be enabled when entering
retention or off state, otherwise waking up might not work
in all situations.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
MPU and CORE should stay awake if there is CAM domain ACTIVE. This is
because that module doesn't have wake-up capability.
This should replace the patch that is currently in the PM branch.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP3 can't generate wakeups in this state, thus it is not permitted.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Using debugfs, export a configurable wakeup timer to be used to
wakeup system from suspend.
If a non-zero value is written to
/debug/pm_debug/wakeup_timer_seconds, A timer wakeup event will wake
the system and resume after the configured number of seconds.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Allow enable/disable of low-power states during idle. To
enable low-power idle:
echo 1 > /debug/pm_debug/sleep_while_idle
to disable:
echo 0 > /debug/pm_debug/sleep_while_idle
Also allow enable/disable of OFF-mode. To enable:
echo 1 > /debug/pm_debug/enable_off_mode
to disable:
echo 0 > /debug/pm_debug/enable_off_mode
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The SMS_SYSCONFIG register gets reset in off mode, added a
save/restore mechanism for that.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The secure sram context save uses dma channels 0 and 1.
In order to avoid collision between kernel DMA transfers and
ROM code dma transfers, we need to reserve DMA channels 0
1 on high security devices.
A bug in ROM code leaves dma irq status bits uncleared.
Hence those irq status bits need to be cleared when restoring
DMA context after off mode.
There was also a faulty parameter given to PPA in the secure
ram context save assembly code, which caused interrupts to
be enabled during secure ram context save. This caused the
save to fail sometimes, which resulted the saved context
to be corrupted, but also left DMA channels in secure mode.
The secure mode DMA channels caused "DMA secure error with
device 0" errors to be displayed.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Fix for ES3.0 bug: SDRC not sending auto-refresh when OMAP wakes-up
from OFF mode (warning for HS devices.)
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The function omap3_save_secure_ram() is now called only once during
the initialization of the device and consequent sleep cycles will
re-use the same saved contents for secure RAM. Users who need secure
services should do secure RAM saving before entering off-mode, if a
secure service has been accessed after last save.
There are both latency and reliability issues with saving secure RAM
context in the idle path. The context save uses a hardware resource
which takes an order of hundreds of milliseconds to initialize after a
wake up from off-mode, and also there is no way of checking whether it
is ready from kernel side or not. It just crashes if you use it too
quickly
Additional fix to ensure scratchpad save is done after secure
RAM by Roger Quadros.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
For HS/EMU devices, some additional resources need to be
saved/restored for off-mode support. Namely, saving the secure RAM
and a pointer to it in the scratchpad.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
For HS/EMU devices, these additional features are also used:
- DMA interrupt disable routine added
- Added DMA controller reset to DMA context restore
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add context save and restore for CORE powerdomain resources in order
to support off-mode.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Adds a 'save_state' option when calling into SRAM idle function
and adds some minor cleanups of SRAM asm code.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
During the MMU restoration on the restore path from MPU OFF, the page
table entry for the page consisting of the code being executed is
modified to make MMU return VA=PA.
The MMU is then enabled and the original entry is being stored in
scratchpad. This patch reads the original values stored in
scratchpad, and restores them back.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Expand the powerdomains handled in the idle path to include PER, NEON
and CORE. This includes properly clearing the previous powerstates,
linking NEON state to MPU state and calling the UART prepare functions
for only the appropraite powerdomain transitions (CORE for UART1,2,
PER for UART3.)
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Generalize the copy of SRAM functions into omap_push_sram_idle()
so it can be used on init but also after off-mode transitions.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
UART3 is in the PER powerdomain. If PER goes idle/inactive
independently of CORE, for UART3 to wakeup it must have its wakeup
enable bits setup in PM_WKEN_PER. This patch enables these bits.
The reason it works when PER and CORE work together is because when
CORE goes inactive/retention, the IOPAD wakeups are enabled and
trigger UART3 wakeup.
Without this patch, when the UART inactivity timer fires for UART3,
its clocks are disabled and it's unable to wakeup so will be unusable
until PER is awoken by another source.
Another way of testing is by keeping CORE on during suspend but
allowing PER to hit retention
# echo 3 > /debug/pm_debug/core_pwrdm/suspend
then enter suspend
# echo mem > /sys/power/state
Without this patch, UART3 will be unable to wakeup the system.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently, only GPIOs in the wakeup domain (GPIOs in bank 0) are
enabled as wakups. This patch also enables GPIOs in the PER
powerdomain (banks 2-6) to be used as possible wakeup sources.
In addition, this patch ensures that all GPIO wakeups can wakeup
the MPU using the PM_MPUGRPSEL_<pwrdm> registers.
NOTE: this doesn't enable the individual GPIOs as wakeups, this simply
enables the per-bank wakeups at the powerdomain level.
This problem was discovered by Mike Chan when preventing the CORE
powerdomain from going into retention/off. When CORE was allowed to
hit retention, GPIO wakeups via IO pad were working fine, but when
CORE remained on, GPIO module-level wakeups were not working properly.
To test, prevent CORE from going inactive/retention/off, thus
preventing the IO chain from being armed:
# echo 3 > /debug/pm_debug/core_pwrdm/suspend
This ensures that GPIO wakeups happen via module-level wakeups and
not via IO pad.
Tested on 3430SDP using the touchscreen GPIO (gpio 2, in WKUP)
Tested on Zoom2 using the QUART interrup GPIO (gpio 102, in PER)
Also, c.f. OMAP PM wiki for troubleshooting GPIO wakeup issues:
http://elinux.org/OMAP_Power_Management
Reported-by: Mike Chan <mikechan@google.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
USBHOST module has 2 fclocks (for HOST1 and HOST2), only one iclock
and only a single bit in the WKST register to indicate a wakeup event.
Because of the single WKST bit, we cannot know whether a wakeup event
was on HOST1 or HOST2, so enable both fclocks before clearing the
wakeup event to ensure both hosts can properly clear the event.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Clearing wakeup sources is now only done when the PRM indicates a
wakeup source interrupt. Since we don't handle any other types of
PRCM interrupts right now, warn if we get any other type of PRCM
interrupt. Either code needs to be added to the PRCM interrupt
handler to react to these, or these other interrupts should be masked
off at init.
Updated after Jon Hunter's PRCM IRQ rework by Kevin Hilman.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
PM_WKST register contents should be ANDed with the contents of the
MPUGRPSEL registers. Otherwise the MPU PRCM interrupt handler could
wind up clearing wakeup events meant for the IVA PRCM interrupt
handler. A future revision to this code should be to read a cached
version of MPUGRPSEL from the powerdomain code, since PRM reads are
relatively slow.
Updated after Jon Hunter's PRCM IRQ change by Kevin Hilman
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There are two scenarios where a race condition could result in a hang
in the prcm_interrupt handler. These are:
1). Waiting for PRM_IRQSTATUS_MPU register to clear.
Bit 0 of the PRM_IRQSTATUS_MPU register indicates that a wake-up event
is pending for the MPU. This bit can only be cleared if the all the
wake-up events latched in the various PM_WKST_x registers have been
cleared. If a wake-up event occurred during the processing of the prcm
interrupt handler, after the corresponding PM_WKST_x register was
checked but before the PRM_IRQSTATUS_MPU was cleared, then the CPU
would be stuck forever waiting for bit 0 in PRM_IRQSTATUS_MPU to be
cleared.
2). Waiting for the PM_WKST_x register to clear.
Some power domains have more than one wake-up source. The PM_WKST_x
registers indicate the source of a wake-up event and need to be cleared
after a wake-up event occurs. When the PM_WKST_x registers are read and
before they are cleared, it is possible that another wake-up event
could occur causing another bit to be set in one of the PM_WKST_x
registers. If this did occur after reading a PM_WKST_x register then
the CPU would miss this event and get stuck forever in a loop waiting
for that PM_WKST_x register to clear.
This patch address the above race conditions that would result in a
hang.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Target state can be read / programmed via files under:
[debugfs]/pm_debug/[pwrdm]/suspend
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add some infrastructure to easily iterate over clock and power
domains.
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch modifies the clock, clockdomain and OMAP3 specific
powerdomain code to call the PM counter infrastructure whenever one or
more powerdomains might have changed state.
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch uses kmalloc(size,GFP_ATOMIC) instead of kmalloc(size,GFP_KERNEL)
to allocate memory for instance of struct power_state in pwrdms_setup(),
since it may be called by pwrdm_for_each() with irq disabled.
It is a easy fix for the following lockdep warning caused by
kmalloc(size,GFP_KERNEL) in pwrdms_setup():
Power Management for TI OMAP3.
------------[ cut here ]------------
WARNING: at kernel/lockdep.c:2282 lockdep_trace_alloc+0xe8/0xfc()
Modules linked in:
[<c0032ccc>] (unwind_backtrace+0x0/0xec) from [<c0056934>] (warn_slowpath_common+0x48/0x60)
[<c0056934>] (warn_slowpath_common+0x48/0x60) from [<c007da10>] (lockdep_trace_alloc+0xe8/0xfc)
[<c007da10>] (lockdep_trace_alloc+0xe8/0xfc) from [<c00cd9bc>] (kmem_cache_alloc+0x28/0x178)
[<c00cd9bc>] (kmem_cache_alloc+0x28/0x178) from [<c000f184>] (pwrdms_setup+0x30/0xf8)
[<c000f184>] (pwrdms_setup+0x30/0xf8) from [<c00381c4>] (pwrdm_for_each+0x64/0x84)
[<c00381c4>] (pwrdm_for_each+0x64/0x84) from [<c000ef60>] (omap3_pm_init+0x3f4/0x5ac)
[<c000ef60>] (omap3_pm_init+0x3f4/0x5ac) from [<c002c2c0>] (do_one_initcall+0x30/0x1d4)
[<c002c2c0>] (do_one_initcall+0x30/0x1d4) from [<c00088d8>] (kernel_init+0xa4/0x118)
[<c00088d8>] (kernel_init+0xa4/0x118) from [<c002ddf8>] (kernel_thread_exit+0x0/0x8)
---[ end trace 1e06f8d97dc5a19b ]---
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Powerdomain previous state is checked after restoring new states in
suspend. This patch fixes this problem.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
It was possible for an unhandled interrupt to occur if there was incoming
serial traffic during wakeup from suspend. This was caused by the code
in arch-arm/mach-omap2/serial.c keeping interrupt enabled all the time,
but not acking its interrupts. Applies on top of PM branch.
Use the PM begin/end hooks to ensure that the "serial idle" interrupts
are disabled during the suspend path. Also, since begin/end hooks are
now used, use the suspend_state that is passed in the begin hook instead
of the enter hook as per the platform_suspend_ops docs.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
By default, prevent functional wakeups from inside a module from
waking up the IVA2. Let DSP Bridge code handle this when loaded.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
By default, prevent functional wakeups from inside a module from
waking up the IVA2. Let DSP Bridge code handle this when loaded.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add D2D clocks (modem_fck, sad2d_ick, mad2d_ick) to clock framework
and ensure that auto-idle bits are set for these clocks during PRCM
init.
Also add omap3_d2d_idle() function called durint PRCM setup which
ensures D2D pins are MUX'd correctly to enable retention for
standalone (no-modem) devices.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch allows the UART clocks to be disabled when the OMAP UARTs
are inactive, thus permitting the chip to hit retention in idle.
After the expiration of an activity timer, each UART is allowed to
disable its clocks so the system can enter retention. The activity
timer is (re)activated on any UART interrupt, UART wake event or any
IO pad wakeup. The actual disable of the UART clocks is done in the
'prepare_idle' hook called from the OMAP idle loop.
While the activity timer is active, the smart-idle mode of the UART is
also disabled. This is due to a "feature" of the UART module that
after a UART wakeup, the smart-idle mode may be entered before the
UART has communicated the interrupt, or upon TX, an idle mode may be
entered before the TX FIFOs are emptied.
Upon suspend, the 'prepare_suspend' hook cancels any pending activity
timers and allows the clocks to be disabled immediately.
In addition, upon disabling clocks the UART state is saved in case
of an off-mode transition while clocks are off.
Special thanks to Tero Kristo for the initial ideas and first versions
of UART idle support, and to Jouni Hogander for extra testing and
bugfixes.
Tested on OMAP3 (Beagle, RX51, SDP, EVM) and OMAP2 (n810)
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch is to sync the core linux-omap PM code with mainline. This
code has evolved and been used for a while the linux-omap tree, but
the attempt here is to finally get this into mainline.
Following this will be a series of patches from the 'PM branch' of the
linux-omap tree to add full PM hardware support from the linux-omap
tree.
Much of this PM core code was written by Jouni Hogander with
significant contributions from Paul Walmsley as well as many others
from Nokia, Texas Instruments and linux-omap community.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
