- fix use-before-set error in ibmphp (Dan Carpenter)
- fix pciehp timeouts caused by Command Completed errata (Bjorn Helgaas)
- fix refcounting in pnv_php hotplug (Julia Lawall)
- clear pciehp Presence Detect and Data Link Layer Status Changed on
resume so we don't miss hotplug events (Mika Westerberg)
- only request pciehp control if we support it, so platform can use ACPI
hotplug otherwise (Mika Westerberg)
- convert SHPC to be builtin only (Mika Westerberg)
- request SHPC control via _OSC if we support it (Mika Westerberg)
- simplify SHPC handoff from firmware (Mika Westerberg)
* pci/hotplug:
PCI: Improve "partially hidden behind bridge" log message
PCI: Improve pci_scan_bridge() and pci_scan_bridge_extend() doc
PCI: Move resource distribution for single bridge outside loop
PCI: Account for all bridges on bus when distributing bus numbers
ACPI / hotplug / PCI: Drop unnecessary parentheses
ACPI / hotplug / PCI: Mark stale PCI devices disconnected
ACPI / hotplug / PCI: Don't scan bridges managed by native hotplug
PCI: hotplug: Add hotplug_is_native()
PCI: shpchp: Add shpchp_is_native()
PCI: shpchp: Fix AMD POGO identification
PCI: shpchp: Use dev_printk() for OSHP-related messages
PCI: shpchp: Remove get_hp_hw_control_from_firmware() wrapper
PCI: shpchp: Remove acpi_get_hp_hw_control_from_firmware() flags
PCI: shpchp: Rely on previous _OSC results
PCI: shpchp: Request SHPC control via _OSC when adding host bridge
PCI: shpchp: Convert SHPC to be builtin only
PCI: pciehp: Make pciehp_is_native() stricter
PCI: pciehp: Rename host->native_hotplug to host->native_pcie_hotplug
PCI: pciehp: Request control of native hotplug only if supported
PCI: pciehp: Clear Presence Detect and Data Link Layer Status Changed on resume
PCI: pnv_php: Add missing of_node_put()
PCI: pciehp: Add quirk for Command Completed errata
PCI: Add Qualcomm vendor ID
PCI: ibmphp: Fix use-before-set in get_max_bus_speed()
# Conflicts:
# drivers/acpi/pci_root.c
- neaten pci=earlydump output (Andy Shevchenko)
- avoid errors when extended config space inaccessible (Gilles Buloz)
- prevent sysfs disable of device while driver attached (Christoph
Hellwig)
- use core interface to report PCIe link properties in bnx2x, bnxt_en,
cxgb4, ixgbe (Bjorn Helgaas)
- remove unused pcie_get_minimum_link() (Bjorn Helgaas)
* pci/enumeration:
PCI: Remove unused pcie_get_minimum_link()
ixgbe: Report PCIe link properties with pcie_print_link_status()
cxgb4: Report PCIe link properties with pcie_print_link_status()
bnxt_en: Report PCIe link properties with pcie_print_link_status()
bnx2x: Report PCIe link properties with pcie_print_link_status()
PCI: Prevent sysfs disable of device while driver is attached
PCI: Check whether bridges allow access to extended config space
x86/PCI: Make pci=earlydump output neat
pci_scan_child_bus_extend() complains when we assign an unreachable
secondary bus number to a bridge. For example, given the topology below:
+-1b.0-[01-39]----00.0-[02-3a]--+-00.0-[03]----00.0
+-01.0-[04-39]--
\-02.0-[3a]----00.0
it logs the following messages:
pci_bus 0000:3a: [bus 3a] partially hidden behind bridge 0000:02 [bus 02-39]
pci_bus 0000:3a: [bus 3a] partially hidden behind bridge 0000:01 [bus 01-39]
These messages are incorrect (0000:02 is a bus, not a bridge) and
confusing. Make the message more understandable:
pci 0000:02:02.0: devices behind bridge are unusable because [bus 3a] cannot be assigned for them
Also, remove the reference to CardBus, because this issue affects all
varieties of PCI, not just CardBus.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
It is not immediately clear what the two functions actually return so
add kernel-doc comment explaining it a bit better.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When distributing extra bus number space to hotplug bridges for future
extension, we don't account for the fact that there might be non-hotplug
bridges on the bus after the hotplug bridges. For example:
01:00.0 --+- 02:00.0 (HotPlug-) -- Thunderbolt host controller
+- 02:01.0 (HotPlug+)
\- 02:02.0 (HotPlug-) -- xHCI host controller
pci_scan_child_bus_extend() is supposed to distribute the remaining bus
numbers to the hotplug bridge at 02:01.0, but only after accounting for all
bridges on bus 02. Since we don't check whether there's another
non-hotplug bridge after the hotplug bridge 02:01.0, it may not leave space
for the non-hotplug bridge:
pci 0000:00:1b.0: PCI bridge to [bus 01-39] (Root Port)
pci 0000:01:00.0: PCI bridge to [bus 02-39]
...
pci 0000:02:00.0: PCI bridge to [bus 03]
pci 0000:02:01.0: PCI bridge to [bus 04]
pci_bus 0000:04: [bus 04-39] extended by 0x35
pci_bus 0000:04: bus scan returning with max=39
pci_bus 0000:04: busn_res: [bus 04-39] end is updated to 39
pci 0000:02:02.0: scanning [bus 00-00] behind bridge, pass 1
pci_bus 0000:3a: scanning bus
pci_bus 0000:3a: bus scan returning with max=3a
pci_bus 0000:3a: busn_res: [bus 3a] end is updated to 3a
pci_bus 0000:3a: [bus 3a] partially hidden behind bridge 0000:02 [bus 02-39]
pci_bus 0000:3a: [bus 3a] partially hidden behind bridge 0000:01 [bus 01-39]
pci_bus 0000:02: bus scan returning with max=3a
pci_bus 0000:02: busn_res: [bus 02-39] end can not be updated to 3a
The resulting 'lspci -t' output looks like this:
+-1b.0-[01-39]----00.0-[02-3a]--+-00.0-[03]----00.0
^^ +-01.0-[04-39]--
\-02.0-[3a]----00.0
^^
The xHCI host controller behind 02:02.0 is not usable because it would have
to be assigned bus 3a, which is not accessible through 00:1b.0.
To fix this, reserve at least one bus for each bridge while scanning
already configured bridges. Then use this information in the second
scan to correct the available extra bus space for hotplug bridges.
After this change the 'lspci -t' output is what is expected:
+-1b.0-[01-39]----00.0-[02-39]--+-00.0-[03]----00.0
+-01.0-[04-38]--
\-02.0-[39]----00.0
The xHCI controller is now on bus 39, where it is usable.
Fixes: 1c02ea8100 ("PCI: Distribute available buses to hotplug-capable bridges")
Reported-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
The SHPC driver now must be builtin (it cannot be a module). If it is
present, request SHPC control immediately when adding the ACPI host bridge.
This is similar to how we handle native PCIe hotplug via pciehp.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rename host->native_hotplug to host->native_pcie_hotplug to make room for a
similar flag for SHPC hotplug.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Fix a memory leak by freeing the PCI resource list in
devm_pci_release_host_bridge_dev().
Fixes: 5c3f18cce0 ("PCI: Add devm_pci_alloc_host_bridge() interface")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Even if a device supports extended config space, i.e., it is a PCI-X Mode 2
or a PCI Express device, the extended space may not be accessible if
there's a conventional PCI bus in the path to it.
We currently figure that out in pci_cfg_space_size() by reading the first
dword of extended config space. On most platforms that returns ~0 data if
the space is inaccessible, but it may set error bits in PCI status
registers, and on some platforms it causes exceptions that we currently
don't recover from.
For example, a PCIe-to-conventional PCI bridge treats config transactions
with a non-zero Extended Register Address as an Unsupported Request on PCIe
and a received Master-Abort on the destination bus (see PCI Express to
PCI/PCI-X Bridge spec, r1.0, sec 4.1.3).
A sample case is a LS1043A CPU (NXP QorIQ Layerscape) platform with the
following bus topology:
LS1043 PCIe Root Port
-> PEX8112 PCIe-to-PCI bridge (doesn't support ext cfg on PCI side)
-> PMC slot connector (for legacy PMC modules)
With a PMC module topology as follows:
PMC connector
-> PCI-to-PCIe bridge
-> PCIe switch (4 ports)
-> 4 PCIe devices (one on each port)
The PCIe devices on the PMC module support extended config space, but we
can't reach it because the PEX8112 can't generate accesses to the extended
space on its secondary bus. Attempts to access it cause Unsupported
Request errors, which result in synchronous aborts on this platform.
To avoid these errors, check whether bridges are capable of generating
extended config space addresses on their secondary interfaces. If they
can't, we restrict devices below the bridge to only the 256-byte
PCI-compatible config space.
Signed-off-by: Gilles Buloz <gilles.buloz@kontron.com>
[bhelgaas: changelog, rework patch so bus_flags testing is all in
pci_bridge_child_ext_cfg_accessible()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Per the PCI Firmware spec r3.2, sec 4.5, an ACPI-based OS should use _OSC
to request control of Latency Tolerance Reporting (LTR) before using it.
Request control of LTR, and if the platform does not grant control, don't
use it.
N.B. If the hardware supports LTR and the ASPM L1.2 substate but the BIOS
doesn't support LTR in _OSC, we previously would enable ASPM L1.2. This
patch will prevent us from enabling ASPM L1.2 in that case. It does not
prevent us from enabling PCI-PM L1.2, since that doesn't depend on LTR.
See PCIe r40, sec 5.5.1, for the L1 PM substate entry conditions.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- move pcieport_if.h to drivers/pci/pcie/ to encapsulate it (Frederick
Lawler)
- merge pcieport_if.h into portdrv.h (Bjorn Helgaas)
- move workaround for BIOS PME issue from portdrv to PCI core (Bjorn
Helgaas)
- completely disable portdrv with "pcie_ports=compat" (Bjorn Helgaas)
- remove portdrv link order dependency (Bjorn Helgaas)
- remove support for unused VC portdrv service (Bjorn Helgaas)
- simplify portdrv feature permission checking (Bjorn Helgaas)
- remove "pcie_hp=nomsi" parameter (use "pci=nomsi" instead) (Bjorn
Helgaas)
- remove unnecessary "pcie_ports=auto" parameter (Bjorn Helgaas)
- use cached AER capability offset (Frederick Lawler)
- don't enable DPC if BIOS hasn't granted AER control (Mika Westerberg)
- rename pcie-dpc.c to dpc.c (Bjorn Helgaas)
* pci/portdrv:
PCI/DPC: Rename from pcie-dpc.c to dpc.c
PCI/DPC: Do not enable DPC if AER control is not allowed by the BIOS
PCI/AER: Use cached AER Capability offset
PCI/portdrv: Rename and reverse sense of pcie_ports_auto
PCI/portdrv: Encapsulate pcie_ports_auto inside the port driver
PCI/portdrv: Remove unnecessary "pcie_ports=auto" parameter
PCI/portdrv: Remove "pcie_hp=nomsi" kernel parameter
PCI/portdrv: Remove unnecessary include of <linux/pci-aspm.h>
PCI/portdrv: Simplify PCIe feature permission checking
PCI/portdrv: Remove unused PCIE_PORT_SERVICE_VC
PCI/portdrv: Remove pcie_port_bus_type link order dependency
PCI/portdrv: Disable port driver in compat mode
PCI/PM: Clear PCIe PME Status bit for Root Complex Event Collectors
PCI/PM: Clear PCIe PME Status bit in core, not PCIe port driver
PCI/PM: Move pcie_clear_root_pme_status() to core
PCI/portdrv: Merge pcieport_if.h into portdrv.h
PCI/portdrv: Move pcieport_if.h to drivers/pci/pcie/
Conflicts:
drivers/pci/pcie/Makefile
drivers/pci/pcie/portdrv.h
- use PCI_EXP_DEVCTL2_COMP_TIMEOUT in rapidio/tsi721 (Bjorn Helgaas)
- remove possible NULL pointer dereference in of_pci_bus_find_domain_nr()
(Shawn Lin)
- report quirk timings with dev_info (Bjorn Helgaas)
- report quirks that take longer than 10ms (Bjorn Helgaas)
- add and use Altera Vendor ID (Johannes Thumshirn)
- tidy Makefiles and comments (Bjorn Helgaas)
* pci/misc:
PCI: Always define the of_node helpers
PCI: Tidy comments
PCI: Tidy Makefiles
mcb: Add Altera PCI ID to mcb-pci
PCI: Add Altera vendor ID
PCI: Report quirks that take more than 10ms
PCI: Report quirk timings with pci_info() instead of pr_debug()
PCI: Fix NULL pointer dereference in of_pci_bus_find_domain_nr()
rapidio/tsi721: use PCI_EXP_DEVCTL2_COMP_TIMEOUT macro
Cache some config data from VF0 and use it for all other VFs instead of
reading it from the config space of each VF. We assume these items are the
same across all associated VFs:
Revision ID
Class Code
Subsystem Vendor ID
Subsystem ID
This is an optimization when enabling SR-IOV on a device with many VFs.
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
[bhelgaas: changelog, simplify comments, remove unused "device", test
CONFIG_PCI_IOV instead of CONFIG_PCI_ATS, rename functions]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Some PCIe features (AER, DPC, hotplug, PME) can be managed by either the
platform firmware or the OS, so the host bridge driver may have to request
permission from the platform before using them. On ACPI systems, this is
done by negotiate_os_control() in acpi_pci_root_add().
The PCIe port driver later uses pcie_port_platform_notify() and
pcie_port_acpi_setup() to figure out whether it can use these features.
But all we need is a single bit for each service, so these interfaces are
needlessly complicated.
Simplify this by adding bits in the struct pci_host_bridge to show when the
OS has permission to use each feature:
+ unsigned int native_aer:1; /* OS may use PCIe AER */
+ unsigned int native_hotplug:1; /* OS may use PCIe hotplug */
+ unsigned int native_pme:1; /* OS may use PCIe PME */
These are set when we create a host bridge, and the host bridge driver can
clear the bits corresponding to any feature the platform doesn't want us to
use.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PCIe 4.0 defines the 16.0 GT/s link speed. Links can run at that speed
without any Linux changes, but previously their sysfs "max_link_speed" and
"current_link_speed" files contained "Unknown speed", not the expected
"16.0 GT/s".
Add decoding for the new 16 GT/s link speed.
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
[bhelgaas: add PCI_EXP_LNKCAP2_SLS_16_0GB]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Dongdong Liu <liudongdong3@huawei.com>
Per PCIe r4.0, sec 9.3.4.1.11, the BAR registers in VF config space are all
RO Zero, so skip sizing them.
This is an optimization when enabling SR-IOV on a device with many VFs.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove pointless comments that tell us the file name, remove blank line
comments, follow multi-line comment conventions. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Per PCIe r4.0, sec 7.5.1.1.9, multi-function devices are required to have a
function 0. Therefore, Linux scans for devices at function 0 (devfn
0/8/16/...) and only scans for other functions if function 0 has its
Multi-Function Device bit set or ARI or SR-IOV indicate there are more
functions.
The Jailhouse hypervisor may pass individual functions of a multi-function
device to a guest without passing function 0, which means a Linux guest
won't find them.
Change Linux PCI probing so it scans all function numbers when running as a
guest over Jailhouse.
This is technically prohibited by the spec, so it is possible that PCI
devices without the Multi-Function Device bit set may have unexpected
behavior in response to this probe.
Originally-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: jailhouse-dev@googlegroups.com
Cc: Benedikt Spranger <b.spranger@linutronix.de>
Cc: linux-pci@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Link: https://lkml.kernel.org/r/06e279b2a3e06cf6689ab3975f8ab592bba02362.1520408357.git.jan.kiszka@siemens.com
Per PCIe r4.0, sec 9.2.1.4, VFs can not implement INTX, and their Interrupt
Line and Interrupt Pin registers must be RO Zero. Some devices have
thousands of VFs, so skip reading the registers as an optimization.
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de>
[bhelgaas: changelog, comment]
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Previously we called pci_probe_reset_function() in this path:
pci_sysfs_init # late_initcall
for_each_pci_dev(dev)
pci_create_sysfs_dev_files(dev)
pci_create_capabilities_sysfs(dev)
pci_probe_reset_function
pci_dev_specific_reset
pcie_has_flr
pcie_capability_read_dword
pci_sysfs_init() is a late_initcall, and a driver may have already claimed
one of these devices and enabled runtime power management for it, so the
device could already be in D3 by the time we get to pci_sysfs_init().
The device itself should respond to the config read even while it's in
D3hot, but if an upstream bridge is also in D3hot, the read won't even
reach the device because the bridge won't forward it downstream to the
device. If the bridge is a PCIe port, it should complete the read as an
Unsupported Request, which may be reported to the CPU as an exception or as
invalid data.
Avoid this case by probing for reset support from pci_init_capabilities(),
before a driver can claim the device. The device may be in D3hot, but any
bridges leading to it should be in D0, so the device's config space should
be fully accessible at that point.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pci/spdx:
PCI: Add SPDX GPL-2.0+ to replace implicit GPL v2 or later statement
PCI: Add SPDX GPL-2.0+ to replace GPL v2 or later boilerplate
PCI: Add SPDX GPL-2.0 to replace COPYING boilerplate
PCI: Add SPDX GPL-2.0 to replace GPL v2 boilerplate
PCI: Add SPDX GPL-2.0 when no license was specified
* lorenzo/pci/cadence:
PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller
dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe endpoint controller
PCI: endpoint: Fix EPF device name to support multi-function devices
PCI: endpoint: Add the function number as argument to EPC ops
PCI: cadence: Add host driver for Cadence PCIe controller
dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe host controller
PCI: Add vendor ID for Cadence
PCI: Add generic function to probe PCI host controllers
PCI: generic: fix missing call of pci_free_resource_list()
PCI: OF: Add generic function to parse and allocate PCI resources
PCI: Regroup all PCI related entries into drivers/pci/Makefile
Conflicts:
drivers/pci/of.c
include/linux/pci.h
* pci/misc:
PCI: Add dummy pci_irqd_intx_xlate() for CONFIG_PCI=n build
PCI: Add wrappers for dev_printk()
PCI: Remove unnecessary messages for memory allocation failures
PCI: Add #defines for Completion Timeout Disable feature
hinic: Replace PCI pool old API
net: e100: Replace PCI pool old API
block: DAC960: Replace PCI pool old API
MAINTAINERS: Include more PCI files
PCI: Remove unneeded kallsyms include
powerpc/pci: Unroll two pass loop when scanning bridges
powerpc/pci: Use for_each_pci_bridge() helper
* pci/enumeration:
RDMA/qedr: Use pci_enable_atomic_ops_to_root()
PCI: Add pci_enable_atomic_ops_to_root()
PCI: Make PCI_SCAN_ALL_PCIE_DEVS work for Root as well as Downstream Ports
This patchs moves generic source code from
drivers/pci/host/pci-host-common.c into drivers/pci/probe.c.
Indeed the extracted lines of code were duplicated by many host
controller drivers. Regrouping them into a generic function gives a
change to properly share this code without introducing a useless
dependency to PCI_HOST_COMMON, which selects PCI_ECAM when not needed by
most host controller drivers.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@free-electrons.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
b24413180f ("License cleanup: add SPDX GPL-2.0 license identifier to
files with no license") added SPDX GPL-2.0 to several PCI files that
previously contained no license information.
Add SPDX GPL-2.0 to all other PCI files that did not contain any license
information and hence were under the default GPL version 2 license of the
kernel.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add PCI-specific dev_printk() wrappers and use them to simplify the code
slightly. No functional change intended.
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
[bhelgaas: squash into one patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCIe Downstream Ports normally have only a Device 0 below them. To
optimize enumeration, we don't scan for other devices *unless* the
PCI_SCAN_ALL_PCIE_DEVS flag is set by set by quirks or the
"pci=pcie_scan_all" kernel parameter.
Previously PCI_SCAN_ALL_PCIE_DEVS only affected scanning below Switch
Downstream Ports, not Root Ports.
But the "Nemo" system, also known as the AmigaOne X1000, has a PA Semi Root
Port whose link leads to an AMD/ATI SB600 South Bridge. The Root Port is a
PCIe device, of course, but the SB600 contains only conventional PCI
devices with no visible PCIe port.
Simplify and restructure only_one_child() so that we scan for all possible
devices below Root Ports as well as Switch Downstream Ports when
PCI_SCAN_ALL_PCIE_DEVS is set.
This is enough to make Nemo work with "pci=pcie_scan_all". We would also
like to add a quirk to set PCI_SCAN_ALL_PCIE_DEVS automatically on Nemo so
users wouldn't have to use the "pci=pcie_scan_all" parameter, but we don't
have that yet.
Link: https://lkml.kernel.org/r/CAErSpo55Q8Q=5p6_+uu7ahnw+53ibVDNRXxrzRV9QnUr_9EUfw@mail.gmail.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198057
Reported-and-Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Enable Latency Tolerance Reporting (LTR). Note that LTR must be enabled in
the Root Port first, and must not be enabled in any downstream device
unless the Root Port and all intermediate Switches also support LTR.
See PCIe r3.1, sec 6.18.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
System BIOS sometimes allocates extra bus space for hotplug-capable PCIe
root/downstream ports. This space is needed if the device plugged to the
port will have more hotplug-capable downstream ports. A good example of
this is Thunderbolt. Each Thunderbolt device contains a PCIe switch and
one or more hotplug-capable PCIe downstream ports where the daisy chain
can be extended.
Currently Linux only allocates minimal bus space to make sure all the
enumerated devices barely fit there. The BIOS reserved extra space is
not taken into consideration at all. Because of this we run out of bus
space pretty quickly when more PCIe devices are attached to hotplug
downstream ports in order to extend the chain.
Modify the PCI core so we distribute the available BIOS allocated bus space
equally between hotplug-capable bridges to make sure there is enough bus
space for extending the hierarchy later on.
Update kernel docs of the affected functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
One can ask more buses to be reserved for hotplug bridges by passing
pci=hpbussize=N in the kernel command line. If the parent bus does not
have enough bus space available we incorrectly create child bus with the
requested number of subordinate buses.
In the example below hpbussize is set to one more than we have available
buses in the root port:
pci 0000:07:00.0: [8086:1578] type 01 class 0x060400
pci 0000:07:00.0: scanning [bus 00-00] behind bridge, pass 0
pci 0000:07:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:07:00.0: scanning [bus 00-00] behind bridge, pass 1
pci_bus 0000:08: busn_res: can not insert [bus 08-ff] under [bus 07-3f] (conflicts with (null) [bus 07-3f])
pci_bus 0000:08: scanning bus
...
pci_bus 0000:0a: bus scan returning with max=40
pci_bus 0000:0a: busn_res: [bus 0a-ff] end is updated to 40
pci_bus 0000:0a: [bus 0a-40] partially hidden behind bridge 0000:07 [bus 07-3f]
pci_bus 0000:08: bus scan returning with max=40
pci_bus 0000:08: busn_res: [bus 08-ff] end is updated to 40
Instead of allowing this, limit the subordinate number to be less than or
equal the maximum subordinate number allocated for the parent bus (if it
has any).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: remove irrelevant dmesg messages]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The current scanning code is really hard to understand because it calls
the same function in a loop where pass value is changed without any
comments explaining it:
for (pass = 0; pass < 2; pass++)
for_each_pci_bridge(dev, bus)
max = pci_scan_bridge(bus, dev, max, pass);
Unfamiliar reader cannot tell easily what is the purpose of this loop
without looking at internals of pci_scan_bridge().
In order to make this bit easier to understand, open-code the loop in
pci_scan_child_bus() and pci_hp_add_bridge() with added comments.
No functional changes intended.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There is not much point of having a file with a single function in it.
Instead we can just move pci_hp_add_bridge() to drivers/pci/probe.c and
make it available always when PCI core is enabled.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: convert printk to dev_err()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The following pattern is often used:
list_for_each_entry(dev, &bus->devices, bus_list) {
if (pci_is_bridge(dev)) {
...
}
}
Add a for_each_pci_bridge() helper to make that code easier to write and
read by reducing indentation level. It also saves one or few lines of code
in each occurrence.
Convert PCI core parts here at the same time.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[bhelgaas: fold in http://lkml.kernel.org/r/20171013165352.25550-1-andriy.shevchenko@linux.intel.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9cLP
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add enhanced Downstream Port Containment support, which prints more
details about Root Port Programmed I/O errors (Dongdong Liu)
- add Layerscape ls1088a and ls2088a support (Hou Zhiqiang)
- add MediaTek MT2712 and MT7622 support (Ryder Lee)
- add MediaTek MT2712 and MT7622 MSI support (Honghui Zhang)
- add Qualcom IPQ8074 support (Varadarajan Narayanan)
- add R-Car r8a7743/5 device tree support (Biju Das)
- add Rockchip per-lane PHY support for better power management (Shawn
Lin)
- fix IRQ mapping for hot-added devices by replacing the
pci_fixup_irqs() boot-time design with a host bridge hook called at
probe-time (Lorenzo Pieralisi, Matthew Minter)
- fix race when enabling two devices that results in upstream bridge
not being enabled correctly (Srinath Mannam)
- fix pciehp power fault infinite loop (Keith Busch)
- fix SHPC bridge MSI hotplug events by enabling bus mastering
(Aleksandr Bezzubikov)
- fix a VFIO issue by correcting PCIe capability sizes (Alex
Williamson)
- fix an INTD issue on Xilinx and possibly other drivers by unifying
INTx IRQ domain support (Paul Burton)
- avoid IOMMU stalls by marking AMD Stoney GPU ATS as broken (Joerg
Roedel)
- allow APM X-Gene device assignment to guests by adding an ACS quirk
(Feng Kan)
- fix driver crashes by disabling Extended Tags on Broadcom HT2100
(Extended Tags support is required for PCIe Receivers but not
Requesters, and we now enable them by default when Requesters support
them) (Sinan Kaya)
- fix MSIs for devices that use phantom RIDs for DMA by assuming MSIs
use the real Requester ID (not a phantom RID) (Robin Murphy)
- prevent assignment of Intel VMD children to guests (which may be
supported eventually, but isn't yet) by not associating an IOMMU with
them (Jon Derrick)
- fix Intel VMD suspend/resume by releasing IRQs on suspend (Scott
Bauer)
- fix a Function-Level Reset issue with Intel 750 NVMe by waiting
longer (up to 60sec instead of 1sec) for device to become ready
(Sinan Kaya)
- fix a Function-Level Reset issue on iProc Stingray by working around
hardware defects in the CRS implementation (Oza Pawandeep)
- fix an issue with Intel NVMe P3700 after an iProc reset by adding a
delay during shutdown (Oza Pawandeep)
- fix a Microsoft Hyper-V lockdep issue by polling instead of blocking
in compose_msi_msg() (Stephen Hemminger)
- fix a wireless LAN driver timeout by clearing DesignWare MSI
interrupt status after it is handled, not before (Faiz Abbas)
- fix DesignWare ATU enable checking (Jisheng Zhang)
- reduce Layerscape dependencies on the bootloader by doing more
initialization in the driver (Hou Zhiqiang)
- improve Intel VMD performance allowing allocation of more IRQ vectors
than present CPUs (Keith Busch)
- improve endpoint framework support for initial DMA mask, different
BAR sizes, configurable page sizes, MSI, test driver, etc (Kishon
Vijay Abraham I, Stan Drozd)
- rework CRS support to add periodic messages while we poll during
enumeration and after Function-Level Reset and prepare for possible
other uses of CRS (Sinan Kaya)
- clean up Root Port AER handling by removing unnecessary code and
moving error handler methods to struct pcie_port_service_driver
(Christoph Hellwig)
- clean up error handling paths in various drivers (Bjorn Andersson,
Fabio Estevam, Gustavo A. R. Silva, Harunobu Kurokawa, Jeffy Chen,
Lorenzo Pieralisi, Sergei Shtylyov)
- clean up SR-IOV resource handling by disabling VF decoding before
updating the corresponding resource structs (Gavin Shan)
- clean up DesignWare-based drivers by unifying quirks to update Class
Code and Interrupt Pin and related handling of write-protected
registers (Hou Zhiqiang)
- clean up by adding empty generic pcibios_align_resource() and
pcibios_fixup_bus() and removing empty arch-specific implementations
(Palmer Dabbelt)
- request exclusive reset control for several drivers to allow cleanup
elsewhere (Philipp Zabel)
- constify various structures (Arvind Yadav, Bhumika Goyal)
- convert from full_name() to %pOF (Rob Herring)
- remove unused variables from iProc, HiSi, Altera, Keystone (Shawn
Lin)
* tag 'pci-v4.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (170 commits)
PCI: xgene: Clean up whitespace
PCI: xgene: Define XGENE_PCI_EXP_CAP and use generic PCI_EXP_RTCTL offset
PCI: xgene: Fix platform_get_irq() error handling
PCI: xilinx-nwl: Fix platform_get_irq() error handling
PCI: rockchip: Fix platform_get_irq() error handling
PCI: altera: Fix platform_get_irq() error handling
PCI: spear13xx: Fix platform_get_irq() error handling
PCI: artpec6: Fix platform_get_irq() error handling
PCI: armada8k: Fix platform_get_irq() error handling
PCI: dra7xx: Fix platform_get_irq() error handling
PCI: exynos: Fix platform_get_irq() error handling
PCI: iproc: Clean up whitespace
PCI: iproc: Rename PCI_EXP_CAP to IPROC_PCI_EXP_CAP
PCI: iproc: Add 500ms delay during device shutdown
PCI: Fix typos and whitespace errors
PCI: Remove unused "res" variable from pci_resource_io()
PCI: Correct kernel-doc of pci_vpd_srdt_size(), pci_vpd_srdt_tag()
PCI/AER: Reformat AER register definitions
iommu/vt-d: Prevent VMD child devices from being remapping targets
x86/PCI: Use is_vmd() rather than relying on the domain number
...
Add a print statement in pci_bus_wait_crs() so that user observes the
progress of device polling instead of silently waiting for timeout to be
reached.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
[bhelgaas: check for timeout first so we don't print "waiting, giving up",
always print time we've slept (not the actual timeout, print a "ready"
message if we've printed a "waiting" message]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Configuration Request Retry Status (CRS) was previously hidden inside
pci_bus_read_dev_vendor_id(). We want to add support for CRS in other
situations, such as waiting for a device to become ready after a Function
Level Reset.
Move CRS handling into pci_bus_wait_crs() so it can be called from other
places.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
[bhelgaas: pass pointer, not value, to pci_bus_wait_crs() so caller gets
correct Vendor ID]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add pci_bus_crs_vendor_id() to determine whether data returned for a config
read of the Vendor ID indicates a Configuration Request Retry Status (CRS)
response.
Per PCIe r3.1, sec 2.3.2, this data is only returned if:
- CRS Software Visibility is enabled,
- a config read includes both bytes of the Vendor ID, and
- the read receives a CRS completion
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
[bhelgaas: changelog, change name to pci_bus_crs_vendor_id(), make static
in probe.c, use it in pci_bus_read_dev_vendor_id()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
While waiting for a device to become ready (i.e., to return a non-CRS
completion to a read of its Vendor ID), if we got a valid response to the
very last read before timing out, we printed a warning and gave up on the
device even though it was actually ready.
For a typical 60s timeout, we wait about 65s (it's not exact because of the
exponential backoff), but we treated devices that became ready between 33s
and 65s as though they failed.
Move the Device ID read later so we check whether the device is ready
before checking for a timeout.
Thanks to Sinan Kaya <okaya@codeaurora.org>, reorder reads so we always
check device presence after sleep, since it's pointless to sleep unless we
recheck afterwards.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When bit4 is set in the PCIe Device Control register, it indicates
whether the device is permitted to use relaxed ordering.
On some platforms using relaxed ordering can have performance issues or
due to erratum can cause data-corruption. In such cases devices must avoid
using relaxed ordering.
The patch adds a new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING to indicate that
Relaxed Ordering (RO) attribute should not be used for Transaction Layer
Packets (TLP) targeted towards these affected root complexes.
This patch checks if there is any node in the hierarchy that indicates that
using relaxed ordering is not safe. In such cases the patch turns off the
relaxed ordering by clearing the capability for this device.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple architectures define this as an empty function, and I'm adding
another one as part of the RISC-V port. Add a __weak version of
pcibios_fixup_bus() and delete the now-obselete ones in a handful of
ports.
The only functional change should be that microblaze used to export
pcibios_fixup_bus(). None of the other architectures exports this, so I
just dropped it.
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Per PCIe r3.1, sec 2.2.6.2 and 7.8.4, a Requester may not use 8-bit Tags
unless its Extended Tag Field Enable is set, but all Receivers/Completers
must handle 8-bit Tags correctly regardless of their Extended Tag Field
Enable.
Some devices do not handle 8-bit Tags as Completers, so add a quirk for
them. If we find such a device, we disable Extended Tags for the entire
hierarchy to make peer-to-peer DMA possible.
The Broadcom HT2100 seems to have issues with handling 8-bit tags. Mark it
as broken.
The pci_walk_bus() in the quirk handles devices we've enumerated in the
past, and pci_configure_device() handles devices we enumerate in the
future.
Fixes: 60db3a4d8c ("PCI: Enable PCIe Extended Tags if supported")
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1467674
Reported-and-tested-by: Wim ten Have <wim.ten.have@oracle.com>
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
[bhelgaas: changelog, tweak messages, rename bit and quirk]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/irq-fixups:
arm64: PCI: Drop DT IRQ allocation from pcibios_alloc_irq()
PCI: xilinx-nwl: Move to struct pci_host_bridge IRQ mapping functions
PCI: rockchip: Move to struct pci_host_bridge IRQ mapping functions
PCI: xgene: Move to struct pci_host_bridge IRQ mapping functions
PCI: altera: Drop pci_fixup_irqs()
PCI: versatile: Drop pci_fixup_irqs()
PCI: generic: Drop pci_fixup_irqs()
PCI: faraday: Drop pci_fixup_irqs()
PCI: designware: Drop pci_fixup_irqs()
PCI: iproc: Drop pci_fixup_irqs()
PCI: rcar: Drop pci_fixup_irqs()
PCI: xilinx: Drop pci_fixup_irqs()
PCI: tegra: Drop pci_fixup_irqs()
ARM/PCI: Remove pci_fixup_irqs() call for bios32 host controllers
PCI: Add a call to pci_assign_irq() in pci_device_probe()
OF/PCI: Update of_irq_parse_and_map_pci() comment
PCI: Add pci_assign_irq() function and have pci_fixup_irqs() use it
PCI: Add IRQ mapping function pointers to pci_host_bridge struct
PCI: Build setup-irq.o on all arches
PCI: Remove pci_scan_root_bus_msi()
PCI: xilinx-nwl: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: rockchip: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: generic: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: xgene: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: xilinx: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: altera: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: versatile: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: iproc: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: rcar: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: aardvark: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: designware: Convert PCI scan API to pci_scan_root_bus_bridge()
ARM/PCI: Convert PCI scan API to pci_scan_root_bus_bridge()
PCI: Make pci_register_host_bridge() PCI core internal
PCI: Add pci_scan_root_bus_bridge() interface
PCI: tegra: Fix host bridge memory leakage
PCI: faraday: Fix host bridge memory leakage
PCI: Add devm_pci_alloc_host_bridge() interface
PCI: Add pci_free_host_bridge() interface
PCI: Initialize bridge release function at bridge allocation
PCI: faraday: Convert IRQ masking to raw PCI config accessors
PCI: iproc: Convert link check to raw PCI config accessors
PCI: xilinx-nwl: Remove nwl_pcie_enable_msi() unused bus parameter
The pci_scan_root_bus_bridge() function allows passing a parameterized
struct pci_host_bridge and scanning the resulting PCI bus; since the struct
msi_controller is part of the struct pci_host_bridge and the struct
pci_host_bridge can now be passed to pci_scan_root_bus_bridge() explicitly,
there is no need for a scan interface with a MSI controller parameter.
With all PCI host controller drivers and platform code relying on
pci_scan_root_bus_msi() converted over to pci_scan_root_bus_bridge() the
pci_scan_root_bus_msi() becomes obsolete and can be removed.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
