"source" comes from the user in snd_ctl_elem_write() so it needs to be
checked.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Fastwel UNIOxx-5 is a PC/104 board, so put COMEDI_UNIOXX5 under
COMEDI_ISA_DRIVERS.
The DIL/Net-PC 1486 is a 486 system, so put COMEDI_SSV_DNP under
COMEDI_MISC_DRIVERS and add a dependency on X86_32 || COMPILE_TEST.
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some circumstances, the performance of this driver is highly degraded,
and ifconfig reports large numbers of dropped packets. By increasing the
maximum RX gain from 0x3e to 0x4e, performance is greatly improved.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch shows the following warning:
drivers/staging/rtl8188eu/core/rtw_ieee80211.c:161 rtw_set_ie() info: ignoring unreachable code.
The cause is a module exit tracing statement after a return.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch reports the following warning:
"drivers/staging/rtl8188eu/core/rtw_mlme_ext.c:8328 mlme_evt_hdl()
error: buffer overflow 'wlanevents' 24 <= 24"
8321 /* checking if event code is valid */
8322 if (evt_code >= MAX_C2HEVT) {
^^^^^^^^^^^^^^^^^^^^^^
8323 RT_TRACE(_module_rtl871x_cmd_c_, _drv_err_, ("\nEvent Code(%d) mismatch!\n", evt_code));
8324 goto _abort_event_;
8325 }
8326
8327 /* checking if event size match the event parm size */
8328 if ((wlanevents[evt_code].parmsize != 0) &&
^^^^^^^^^^^^^^^^^^^^
8329 (wlanevents[evt_code].parmsize != evt_sz)) {
8330 RT_TRACE(_module_rtl871x_cmd_c_, _drv_err_,
8331 ("\nEvent(%d) Parm Size mismatch (%d vs %d)!\n",
8332 evt_code, wlanevents[evt_code].parmsize, evt_sz));
8333 goto _abort_event_;
8334 }
This warning results because the number of items in "enum rtw_c2h_event",
which determines the value of MAX_C2HEVT, is one more than in "struct wlanevents".
Adding an extra dummy event to the latter fixes the problem.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch reports the following warning:
"drivers/staging/rtl8188eu/hal/rtl8188e_hal_init.c:2008
Hal_ReadPowerValueFromPROM_8188E()
error: buffer overflow 'pwrInfo24G->IndexBW40_Base[rfPath]' 5 <= 5"
drivers/staging/rtl8188eu/hal/rtl8188e_hal_init.c
2005 /* 2.4G default value */
2006 for (group = 0; group < MAX_CHNL_GROUP_24G; group++) {
2007 pwrInfo24G->IndexCCK_Base[rfPath][group] = EEPROM_DEFAULT_24G_INDEX;
2008 pwrInfo24G->IndexBW40_Base[rfPath][group] = EEPROM_DEFAULT_24G_INDEX;
The reason is that IndexCCK_Base[] has MAX_CHNL_GROUP_24G elements, but
IndexBW40_Base is smaller by 1. Make them both have MAX_CHNL_GROUP_24G
elements.
Reported by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mips allmodconfig fails with
ERROR: "copy_from_user_page" [drivers/staging/lustre/lustre/libcfs/libcfs.ko]
undefined!
which is due to LUSTRE using copy_from_user_page which is not exported by any
architecture. Unfortunately, LUSTRE can only be built as module, so there is no
easy fix.
MIPS, SH, and optionally XTENSA implement copy_from_user_page as unexported
functions. Disable LUSTRE for those.
Cc: Peng Tao <bergwolf@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit c70bda992c.
It's incorrect, Kay writes:
Please just remove it. "devname" is meant to be used for
single-instance devices with a static dev_t, never for things
like zramX.
It will not do anything useful here, it does nothing really
without a statically assigned dev_t, and it should not be used
for devices of this kind anyway.
Reported-by: Tom Gundersen <teg@jklm.no>
Reported-by: Kay Sievers <kay@vrfy.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove skb allocation failure warnings. They will trigger a page
allocation warning already. Also, one of the warnings was not ratelimited,
causing the box to lock up under heavy traffic & low memory.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: David Daney <david.daney@cavium.com>
Acked-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should count also dropped packets, otherwise the NAPI handler may
end up running too long.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It duplicates the definition in arch/alpha/include/asm/pgtable.h and emits
warnings.
Cc: Andreas Dilger <andreas.dilger@intel.com>
Cc: Peng Tao <tao.peng@emc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that format strings cannot leak into printk() calls from the
msgbuf string.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes up the usage of snprintf, strncpy, and format strings in the
call to kthread_run to avoid ever accidentally allowing a format string
into the thread name.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The boot message buffer could potentially overflow the stack and the
heap. Additionally make sure format strings could not leak into printk()
calls.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/staging/rtl8188eu/core/rtw_wlan_util.c: In function ‘WMMOnAssocRsp’:
drivers/staging/rtl8188eu/core/rtw_wlan_util.c:634: warning: ‘change_inx’ may be used uninitialized in this function
And the compiler is right: change_inx should be initialized to false.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LUSTRE_TRANSLATE_ERRNOS is never enabled, a "true" is not a valid value.
Use "default y" instead of "default true" to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The indentation in the swGetOFDMControlRate function is screwed up.
At first it appears that there are missing braces on a multi-line if, but
looking at history, commit dd0a774fc7
("staging: vt6656: card/main_usb/device use new structure names")
incorrectly indented the two lines below.
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the DTS data for ocp2scp node by adding the
missing reg property.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
USB3 block has a 64KiB space, another 64KiB is
used for the wrapper.
Without this change, resource_size() will get
confused and driver won't probe because size
will be negative.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The BeagleBone Black is basically a regular BeagleBone with eMMC and
HDMI added, so create a common dtsi both can use.
IMPORTANT: booting the existing am335x-bone.dts will blow up the HDMI
transceiver after a dozen boots with an uSD card inserted because LDO
will be at 3.3V instead of 1.8.
MMC support for AM335x still isn't in, so only the LDO change has been
added.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Tom Rini <trini@ti.com>
Tested-by: Matt Porter <matt.porter@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The beagle and beagle-xm entries were inside the same double quote.
Split them to have two distinct entries.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
boot_cpu_data is used the same as current_cpu_data but returns the CPU
data for CPU 0. This means it doesn't have to use smp_processor_id()
thus no need to disable preemption.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When we cancel 'async_pf_execute()', we should behave as if the work was
never scheduled in 'kvm_setup_async_pf()'.
Fixes a bug when we can't unload module because the vm wasn't destroyed.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After nested vmentry stale cache can be used to reload L2 PDPTR pointers
which will cause L2 guest to fail. Fix it by invalidating cache on nested
vmentry emulation.
https://bugzilla.kernel.org/show_bug.cgi?id=60830
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Page tables in a read-only memory slot will currently cause a triple
fault because the page walker uses gfn_to_hva and it fails on such a slot.
OVMF uses such a page table; however, real hardware seems to be fine with
that as long as the accessed/dirty bits are set. Save whether the slot
is readonly, and later check it when updating the accessed and dirty bits.
Reviewed-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Reviewed-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Opcode CA
This gets used by a DOS based NetWare guest.
Signed-off-by: Bruce Rogers <brogers@suse.com>
Reviewed-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove skb allocation failure warnings. They will trigger a page
allocation warning already. Also, one of the warnings was not ratelimited,
causing the box to lock up under heavy traffic & low memory.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: David Daney <david.daney@cavium.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: devel@driverdev.osuosl.org
Cc: linux-mips@linux-mips.org
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: richard@nod.at
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Patchwork: https://patchwork.linux-mips.org/patch/5811/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We should count also dropped packets, otherwise the NAPI handler may
end up running too long.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: devel@driverdev.osuosl.org
Cc: linux-mips@linux-mips.org
Cc: David Daney <david.daney@cavium.com>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: richard@nod.at
Patchwork: https://patchwork.linux-mips.org/patch/5809/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
the wake_up_process func is included by spin_lock/unlock in
vhost_work_queue,
but it could be done outside the spin_lock.
I have test it with kernel 3.0.27 and guest suse11-sp2 using iperf,
the num as below.
original modified
thread_num tp(Gbps) vhost(%) | tp(Gbps) vhost(%)
1 9.59 28.82 | 9.59 27.49
8 9.61 32.92 | 9.62 26.77
64 9.58 46.48 | 9.55 38.99
256 9.6 63.7 | 9.6 52.59
Signed-off-by: Chuanyu Qin <qinchuanyu@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The patch "0b7a76a ARM: dts: imx6q{dl}: add DTE pads for uart"
adds the DTE pads for uart. For PAD_EIM_D29, the offset of the
Pad Mux register should be 0x0c8, not 0x0c4.
This patch fixes it.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The L2 cache controller(PL310) version on the i.MX6D/Q is r3p1-50rel0
The L2 cache controller(PL310) version on the i.MX6DL/SOLO/SL is r3p2
But according to ARM PL310 errata: 752271
ID: 752271: Double linefill feature can cause data corruption
Fault Status: Present in: r3p0, r3p1, r3p1-50rel0. Fixed in r3p2
Workaround: The only workaround to this erratum is to disable the
double linefill feature. This is the default behavior.
without this patch, you will meet the following error when run the
memtester application at: http://pyropus.ca/software/memtester/
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365664.
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365668.
FAILURE: 0x00100000 != 0x00200000 at offset 0x0136566c.
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365670.
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365674.
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365678.
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Commit 718a350 (ARM: i.MX51: Add PATA support) adds pata support to the
imx51.dtsi file and is using clock 161. The problem is that the right
clock is 172, according to commit 5d530bb (ARM: i.MX5: Add PATA and SRTC
clocks). Using the clock 172 makes things work again (and kills a nasty
system freeze).
Tested-by: Steev Klimaszewski <steev@gentoo.org>
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since commit beb2d1c1ba (ARM i.MX5: Add S/PDIF clocks), the following clock
error appears on mx51:
TrustZone Interrupt Controller (TZIC) initialized
i.MX51 clk 180: register failed with -17
i.MX5 clk 180: register failed with -17
sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
CPU identified as i.MX51, silicon rev 3.0
...
Clock 180 corresponds to 'spdif1_podf' and this clock is getting registered
twice.
Fix it, by properly registering the 'spdif1_pred' clock, which should not
reference 'spdif1_podf'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The clk_init_data.flags of clk-fixup-mux is left there without
initialization. It may hold some random data and cause clock framework
interpret the clock in an unexpected way. At least on imx6sl, the
following division by zero error with sched_clock is seen because of it.
Division by zero in kernel.
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.11.0-rc3+ #19
Backtrace:
[<80011af0>] (dump_backtrace+0x0/0x10c) from [<80011c90>] (show_stack+0x18/0x1c)
r6:3b9aca00 r5:00000020 r4:00000000 r3:00000000
[<80011c78>] (show_stack+0x0/0x1c) from [<8055e02c>] (dump_stack+0x78/0x94)
[<8055dfb4>] (dump_stack+0x0/0x94) from [<80011924>] (__div0+0x18/0x20)
r4:00000000 r3:00000000
[<8001190c>] (__div0+0x0/0x20) from [<8026c408>] (Ldiv0_64+0x8/0x18)
[<8006330c>] (clocks_calc_mult_shift+0x0/0xf8) from [<8072f604>] (setup_sched_clock+0x88/0x1f0)
[<8072f57c>] (setup_sched_clock+0x0/0x1f0) from [<8071ad48>] (mxc_timer_init+0xe8/0x17c)
[<8071ac60>] (mxc_timer_init+0x0/0x17c) from [<807290b0>] (imx6sl_clocks_init+0x1db8/0x1dc0)
r8:807a9ca4 r7:00000000 r6:80777564 r5:8100c1f4 r4:c0820000
[<807272f8>] (imx6sl_clocks_init+0x0/0x1dc0) from [<807420ac>] (of_clk_init+0x40/0x6c)
[<8074206c>] (of_clk_init+0x0/0x6c) from [<807290cc>] (imx6sl_timer_init+0x14/0x18)
r5:807a8e80 r4:ffffffff
[<807290b8>] (imx6sl_timer_init+0x0/0x18) from [<80716e1c>] (time_init+0x24/0x34)
[<80716df8>] (time_init+0x0/0x34) from [<80713738>] (start_kernel+0x1b0/0x310)
[<80713588>] (start_kernel+0x0/0x310) from [<80008074>] (0x80008074)
r7:80770b08 r6:80754cd4 r5:8076c8c4 r4:10c53c7d
sched_clock: 32 bits at 0 Hz, resolution 0ns, wraps every 0ms
Fix the bug by initializing init.flags as zero.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Ben Hutchings says:
====================
Some bug fixes and future-proofing for the recently added SFC9120
support:
1. Minimal support for the 40G configuration.
2. Disable the incomplete PTP/hardware timestamping support.
3. Reset MAC stats properly after a firmware upgrade.
4. Re-check the datapath firmware capabilities after the controller is
reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapt the same behaviour for SCTP as present in TCP for ICMP redirect
messages. For IPv6, RFC4443, section 2.4. says:
...
(e) An ICMPv6 error message MUST NOT be originated as a result of
receiving the following:
...
(e.2) An ICMPv6 redirect message [IPv6-DISC].
...
Therefore, do not report an error to user space, just invoke dst's redirect
callback and leave, same for IPv4 as done in TCP as well. The implication
w/o having this patch could be that the reception of such packets would
generate a poll notification and in worst case it could even tear down the
whole connection. Therefore, stop updating sk_err on redirects.
Reported-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Suggested-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use USB_DEVICE_AND_INTERFACE_INFO and USB_VENDOR_AND_INTERFACE_INFO
macros to reduce boilerplate.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Cc: <stable@vger.kernel.org> # 3.0+ as far back as it applies cleanly
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IFLA_IPTUN_LOCAL and IFLA_IPTUN_REMOTE were inverted.
Introduced by c075b13098 (ip6tnl: advertise tunnel param via rtnl).
Signed-off-by: Ding Zhi <zhi.ding@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>