Only rx/tx pause settings.
Autoneg setting is currently not supported.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Port speed settings are applied by the device only upon
port admin status transition from DOWN to UP.
So we enforce this transition regardless of the port's
current operation state (which may be occasionally DOWN if
for example the network cable is disconnected).
- Fix the PORT_UP/DOWN device interface enum
- Set the local_port bit in the device PAOS register
- EXPORT the PAOS (Port Administrative and Operational Status)
register set/query access functions.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added physical port counters in the following standard formats to
ethtool statistics:
- IEEE 802.3
- RFC2863
- RFC2819
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create/destroy TIRs, TISs and flow tables upon PCI probe/remove rather
than upon the netdev ndo_open/stop.
Upon ndo_stop(), redirect all RX traffic to the (lately introduced)
"Drop RQ" and then close only the RX/TX rings, leaving the TIRs,
TISs and flow tables alive.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be used by the mlx5 Eth driver in following commit.
This is in preparation for netdev "light-weight" open/stop flow
change described in previous commit.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A regular TX WQE execution involves two or more DMA reads -
one to fetch the WQE, and another one per WQE gather entry.
These DMA reads obviously increase the TX latency.
There are two mlx5 mechanisms to bypass these DMA reads:
1) Inline WQE
2) Blue Flame (BF)
An inline WQE contains a whole packet, thus saves the DMA read/s
of the regular WQE gather entry/s. Inline WQE support was already
added in the previous commit.
A BF WQE is written directly to the device I/O mapped memory, thus
enables saving the DMA read that fetches the WQE.
The BF WQE I/O write must be in cache line granularity, thus uses
the CPU write combining mechanism.
A BF WQE I/O write acts also as a TX doorbell for notifying the
device of new TX WQEs.
A BF WQE is written to the same I/O mapped address as the regular TX
doorbell, thus this address is being mapped twice - once by ioremap()
and once by io_mapping_map_wc().
While both mechanisms reduce the TX latency, they both consume more CPU
cycles than a regular WQE:
- A BF WQE must still be written to host memory, in addition to being
written directly to the device I/O mapped memory.
- An inline WQE involves copying the SKB data into it.
To handle this tradeoff, we introduce here a heuristic algorithm that
strives to avoid using these two mechanisms in case the TX queue is
being back-pressured by the device, and limit their usage rate otherwise.
An inline WQE will always be "Blue Flamed" (written directly to the
device I/O mapped memory) while a BF WQE may not be inlined (may contain
gather entries).
Preliminary testing using netperf UDP_RR shows that the latency goes down
from 17.5us to 16.9us, while the message rate (tested with pktgen) stays
the same.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By affinity hints and XPS, each mlx5e channel is assigned a CPU
core.
Channel DMA coherent memory that is written by the NIC and read
by SW (e.g CQ buffer) is allocated on the NUMA node of the CPU
core assigned for the channel.
Channel DMA coherent memory that is written by SW and read by the
NIC (e.g SQ/RQ buffer) is allocated on the NUMA node of the NIC.
Doorbell record (written by SW and read by the NIC) is an
exception since it is accessed by SW more frequently.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ConnectX-4 HW implements inverted XOR8.
To make it act as XOR we re-order the HW RSS indirection table.
Set XOR to be the default RSS hash function and add ethtool API to
control it.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Add TX fast path in mac80211, from Johannes Berg.
2) Add TSO/GRO support to ibmveth, from Thomas Falcon
3) Move away from cached routes in ipv6, just like ipv4, from Martin
KaFai Lau.
4) Lots of new rhashtable tests, from Thomas Graf.
5) Run ingress qdisc lockless, from Alexei Starovoitov.
6) Allow servers to fetch TCP packet headers for SYN packets of new
connections, for fingerprinting. From Eric Dumazet.
7) Add mode parameter to pktgen, for testing receive. From Alexei
Starovoitov.
8) Cache access optimizations via simplifications of build_skb(), from
Alexander Duyck.
9) Move page frag allocator under mm/, also from Alexander.
10) Add xmit_more support to hv_netvsc, from KY Srinivasan.
11) Add a counter guard in case we try to perform endless reclassify
loops in the packet scheduler.
12) Extern flow dissector to be programmable and use it in new "Flower"
classifier. From Jiri Pirko.
13) AF_PACKET fanout rollover fixes, performance improvements, and new
statistics. From Willem de Bruijn.
14) Add netdev driver for GENEVE tunnels, from John W Linville.
15) Add ingress netfilter hooks and filtering, from Pablo Neira Ayuso.
16) Fix handling of epoll edge triggers in TCP, from Eric Dumazet.
17) Add an ECN retry fallback for the initial TCP handshake, from Daniel
Borkmann.
18) Add tail call support to BPF, from Alexei Starovoitov.
19) Add several pktgen helper scripts, from Jesper Dangaard Brouer.
20) Add zerocopy support to AF_UNIX, from Hannes Frederic Sowa.
21) Favor even port numbers for allocation to connect() requests, and
odd port numbers for bind(0), in an effort to help avoid
ip_local_port_range exhaustion. From Eric Dumazet.
22) Add Cavium ThunderX driver, from Sunil Goutham.
23) Allow bpf programs to access skb_iif and dev->ifindex SKB metadata,
from Alexei Starovoitov.
24) Add support for T6 chips in cxgb4vf driver, from Hariprasad Shenai.
25) Double TCP Small Queues default to 256K to accomodate situations
like the XEN driver and wireless aggregation. From Wei Liu.
26) Add more entropy inputs to flow dissector, from Tom Herbert.
27) Add CDG congestion control algorithm to TCP, from Kenneth Klette
Jonassen.
28) Convert ipset over to RCU locking, from Jozsef Kadlecsik.
29) Track and act upon link status of ipv4 route nexthops, from Andy
Gospodarek.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1670 commits)
bridge: vlan: flush the dynamically learned entries on port vlan delete
bridge: multicast: add a comment to br_port_state_selection about blocking state
net: inet_diag: export IPV6_V6ONLY sockopt
stmmac: troubleshoot unexpected bits in des0 & des1
net: ipv4 sysctl option to ignore routes when nexthop link is down
net: track link-status of ipv4 nexthops
net: switchdev: ignore unsupported bridge flags
net: Cavium: Fix MAC address setting in shutdown state
drivers: net: xgene: fix for ACPI support without ACPI
ip: report the original address of ICMP messages
net/mlx5e: Prefetch skb data on RX
net/mlx5e: Pop cq outside mlx5e_get_cqe
net/mlx5e: Remove mlx5e_cq.sqrq back-pointer
net/mlx5e: Remove extra spaces
net/mlx5e: Avoid TX CQE generation if more xmit packets expected
net/mlx5e: Avoid redundant dev_kfree_skb() upon NOP completion
net/mlx5e: Remove re-assignment of wq type in mlx5e_enable_rq()
net/mlx5e: Use skb_shinfo(skb)->gso_segs rather than counting them
net/mlx5e: Static mapping of netdev priv resources to/from netdev TX queues
net/mlx4_en: Use HW counters for rx/tx bytes/packets in PF device
...
Enable HW cacheline start padding and align RX WQE size to cacheline
while considering HW start padding. Also, fix dma_unmap call to use
the correct SKB data buffer size.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we configured HW MTU to be netdev->mtu, actually we
need to configure netdev->mtu + (ETH_HLEN + VLAN_HLEN + ETH_FCS_LEN).
Also, query MTU can not fail, hence make the relevant helper a
void functionm, add mlx5e_set_dev_port_mtu, helper function to
handle MTU setting.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix static checker warnings in the flow of system guid query.
Fixes: 707c4602cd ('net/mlx5_core: Add new query HCA vport commands')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the following helpers:
1. mlx5_query_port_proto_oper -- queries the port speed port mask
2. mlx5_query_port_link_width_oper - queries the port link with bitmask
3. mlx5_query_port_vl_hw_cap - queries the Virtual Lanes supported on this port
These helpers will be used from the IB driver when working in ISSI > 0 mode.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, mlx5_query_port_ptys always queried port number one.
Added new argument in the function's prototype so we can also query
the second port. This will be needed when thr helper will be invoked
from the IB driver on non FPP (Function-Per-Port) devices.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the function prototypes for max and operational mtu to take the
local port number. In the Ethernet driver is this hard coded to one,
since ConnectX4 Ethernet devices are always function-per-port.
The IB driver also serves older devices (ConnectIB) which isn't such,
and hence the part can vary.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two wrapper functions to the query adapter command:
1. mlx5_query_board_id -- replaces the old mlx5_cmd_query_adapter.
2. mlx5_core_query_vendor_id -- retrieves the vendor_id from the
query_adapter command.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added the implementation for the following commands:
1. QUERY_HCA_VPORT_GID
2. QUERY_HCA_VPORT_PKEY
3. QUERY_HCA_VPORT_CONTEXT
They will be needed when we move to work with ISSI > 0 in the IB driver too.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the vport header file to be under include/linux/mlx5, such that
the mlx5 IB can use it as well.
Also add nic_ prefix to the vport NIC commands to differeniate between
HCA vport commands and NIC vport commands.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When working in ISSI > 0 mode, the model exposed by the device for
XRCs and SRQs is different. XRCs use XRC SRQs and plain SRQs are based
on RPM (Receive Memory Pool).
Add helper functions to create, modify, query, and arm XRC SRQs and RMPs.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The process_mad device function declares some parameters as "in". Make those
parameters const and adjust the call tree under process_mad in the various
drivers accordingly.
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This is the Ethernet part of the driver for the Mellanox ConnectX(R)-4
Single/Dual-Port Adapter supporting 100Gb/s with VPI. The driver
extends the existing mlx5 driver with Ethernet functionality.
This patch contains the driver entry points but does not include
transmit and receive (see the previous patch in the series) routines.
It also adds the option MLX5_CORE_EN to Kconfig to enable/disable the
Ethernet functionality. Currently, Kconfig is programmed to make
Ethernet and Infiniband functionality mutally exclusive.
Also changed MLX5_INFINIBAND to be depandant on MLX5_CORE instead of
selecting it, since MLX5_CORE could be selected without MLX5_INFINIBAND
being selected.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains the resource handling files:
- flow_table.c: This file contains the code to handle the low level API
to configure hardware flow table. It is separated from
the flow_table_en.c, because it will be used in the
future by Raw Ethernet QP in mlx5_ib too.
- en_flow_table.[ch]: Ethernet flow steering handling. The flow table
object contain a mapping between flow specs and TIRs.
This mechanism will be used also to configure e-switch
in the future, when SR-IOV support will be added.
- transobj.[ch] - Low level functions to create/modify/destroy the
transport objects: RQ/SQ/TIR/TIS
- vport.[ch] - Handle attributes of a virtual port (vPort) in the
embedded switch. Currently this switch is a passthrough, until SR-IOV
support will be added.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce set/Query low level functions to access MTU in hardware. To be
used by the netdev.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce mlx5_core_modify_cq_moderation() to be used by the netdev, to
set hardware coalescing.
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implemet get/set port status low level functions to be exposed by the
netdev.
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Those registers will be used by the ethtool to set/get settings.
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Query all supported types of dev caps on driver load.
- Store the Cap data outbox per cap type into driver private data.
- Introduce new Macros to access/dump stored caps (using the auto
generated data types).
- Obsolete SW representation of dev caps (no need for SW copy for each
cap).
- Modify IB driver to use new macros for checking caps.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5_ifc.h was heavily modified here since it is now generated by a
script from the device specification (PRM rev 0.25). This specification
is backward compatible to existing hardware.
Some structures/fields were added here in order to enable the Ethernet
functionality of the driver.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preparation for upcoming ethernet driver.
- Move msix array from eq_table struct to priv since its not related to
eq_table
- Intorduce irq_info struct to hold all irq information
- Move name from mlx5_eq to irq_info struct since it is irq property.
- Set IRQ affinity hints
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As David Daney pointed in mlx4_core driver [1], mlx5_core is also
misusing the DMA-API.
This patch is removing the code that vmap() memory allocated by
dma_alloc_coherent().
After this patch, users of this drivers might fail allocating resources
on memory fragmeneted systems. This will be fixed later on.
[1] - https://patchwork.ozlabs.org/patch/458531/
CC: David Daney <david.daney@cavium.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preparation for ethernet driver.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass consumer index as a parameter to arm CQ
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preparation for ethernet driver.
These functions will be used in drivers other than mlx5_ib.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use coherent memory for the commands descriptor page. Take measures to make
sure the page is aligned to MLX5_ADAPTER_PAGE_SIZE as required by the hardware.
Reported-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implement a page fault handler (leaving the pages pinned as
of time being). The page fault handler handles initiator and responder
page faults for UD/RC transports, for send/receive operations, as well
as RDMA read/write initiator support.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* Refactor MR registration and cleanup, and fix reg_pages accounting.
* Create a work queue to handle page fault events in a kthread context.
* Register a fault handler to get events from the core for each QP.
The registered fault handler is empty in this patch, and only a later
patch implements it.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The new function allows updating the page tables of a memory region
after it was created. This can be used to handle page faults and page
invalidations.
Since mlx5_ib_update_mtt will need to work from within page invalidation,
so it must not block on memory allocation. It employs an atomic memory
allocation mechanism that is used as a fallback when kmalloc(GFP_ATOMIC) fails.
In order to reuse code from mlx5_ib_populate_pas, the patch splits
this function and add the needed parameters.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch wraps together several changes needed for on-demand paging support
in the mlx5_ib_populate_pas function, and when registering memory regions.
* Instead of accepting a UMR bit telling the function to enable all
access flags, the function now accepts the access flags themselves.
* For on-demand paging memory regions, fill the memory tables from the
correct list, and enable/disable the access flags per-page according
to whether the page is present.
* A new bit is set to enable writing of access flags when using the
firmware create_mkey command.
* Disable contig pages when on-demand paging is enabled.
In addition the patch changes the UMR code to use PTR_ALIGN instead of
our own macro.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* Add a handler function pointer in the mlx5_core_qp struct for page
fault events. Handle page fault events by calling the handler
function, if not NULL.
* Add on-demand paging capability query command.
* Export command for resuming QPs after page faults.
* Add various constants related to paging support.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In commit 0c7aac854f ("net/mlx5_core: Remove unused dev cap enum
fields"), the flag MLX5_DEV_CAP_FLAG_ON_DMND_PG was removed.
Unfortunately the on-demand paging changes actually use it, so re-add
the missing flag.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add a helper function mlx5_ib_read_user_wqe to read information from
user-space owned work queues. The function will be used in a later
patch by the page-fault handling code in mlx5_ib.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
[ Add stub for ib_umem_copy_from() for CONFIG_INFINIBAND_USER_MEM=n
- Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
The current UMR interface doesn't allow partial updates to a memory
region's page tables. This patch changes the interface to allow that.
It also changes the way the UMR operation validates the memory
region's state. When set, IB_SEND_UMR_FAIL_IF_FREE will cause the UMR
operation to fail if the MKEY is in the free state. When it is
unchecked the operation will check that it isn't in the free state.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
- Large set of iSER initiator improvements
- Hardware driver fixes for cxgb4, mlx5 and ocrdma
- Small fixes to core midlayer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+ABw
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/RDMA updates from Roland Dreier:
- large set of iSER initiator improvements
- hardware driver fixes for cxgb4, mlx5 and ocrdma
- small fixes to core midlayer
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (47 commits)
RDMA/cxgb4: Fix ntuple calculation for ipv6 and remove duplicate line
RDMA/cxgb4: Add missing neigh_release in find_route
RDMA/cxgb4: Take IPv6 into account for best_mtu and set_emss
RDMA/cxgb4: Make c4iw_wr_log_size_order static
IB/core: Fix XRC race condition in ib_uverbs_open_qp
IB/core: Clear AH attr variable to prevent garbage data
RDMA/ocrdma: Save the bit environment, spare unncessary parenthesis
RDMA/ocrdma: The kernel has a perfectly good BIT() macro - use it
RDMA/ocrdma: Don't memset() buffers we just allocated with kzalloc()
RDMA/ocrdma: Remove a unused-label warning
RDMA/ocrdma: Convert kernel VA to PA for mmap in user
RDMA/ocrdma: Get vlan tag from ib_qp_attrs
RDMA/ocrdma: Add default GID at index 0
IB/mlx5, iser, isert: Add Signature API additions
Target/iser: Centralize ib_sig_domain setting
IB/iser: Centralize ib_sig_domain settings
IB/mlx5: Use extended internal signature layout
IB/iser: Set IP_CSUM as default guard type
IB/iser: Remove redundant assignment
IB/mlx5: Use enumerations for PI copy mask
...
Rather than using the basic BSF layout which utilizes a pre-configured
signature settings (sufficient for current DIF implementation), we use
the extended BSF layout to expose advanced signature settings. These
settings will also be exposed to the user later.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In case input and output space parameters match, we can use a copy
mask from input and output space. Use enums for those.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch puts a common part as the first field of mlx5_core_qp. This field is
used to identify which resource generated an event. This is required since upcoming
new resource types such as DC targets are allocated for the same numerical space
as regular QPs and may generate the same events. By searching the resource in the
same table we can then look at the common field to identify the resource.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transform device capabilities related commands to use set/get macros to
manipulate command mailboxes.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Achiad Shochat