Call ata_bmdma_irq_clear() directly instead of through
ap->ops->irq_clear() according to libata style guideline.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fixes bogus accesses to ports 0-15 with a non DMA capable controller.
This I think should go in for 2.6.20
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some uli controllers have stuck SIMPLEX bit which can't be cleared
with ata_pci_clear_simplex(), but the controller is capable of doing
DMAs on both channels simultaneously. Implement ATA_FLAG_IGN_SIMPLEX
which makes libata ignore the simplex bit and use it in sata_uli.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We're still seeing a lot of issues with NCQ implementation in drive
firmwares. Sprious FISes during NCQ command phase occur on many
drives and some of them seem potentially dangerous (at least to me).
Until we find the solution, spurious messages can give us more info.
Improve and limit them such that more info can be reported while not
disturbing users too much.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
vt6420 completely loses its ability to raise IRQ for ATAPI devices if
ATA_NIEN is diddled with in ->freeze. Further investigation is
necessary to determine whether this problem is shared on other
controllers but it doesn't seem to be at this point.
Make vt6420's ->freeze only clear IRQ to fix this problem. This makes
vt6420 relatively more prone to IRQ storms but the controller is way
too braindamaged to worry about that anyway.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When set_mode() changed ->set_mode didn't adapt. This makes the needed
changes and removes the relevant FIXME case.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rather than ending up with two layers of negation jut rename the variable
and lose one.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fixup the inialization of qc->n_elem. It currently gets
initialized to 1 for commands that do not transfer any data.
Fix this by initializing n_elem to 0 and only setting to 1
in ata_scsi_qc_new when there is data to transfer. This fixes
some problems seen with SATA devices attached to ipr adapters.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some ATA/ATAPI devices act weirdly after the link is put into slumber
mode. Some hang completely requiring physical power removal while
others fail to wake up till the link is hardreset a couple of times.
The addition of slumber on power down was never driven by real need.
It just followed what ahci spec said literally. The spec itself seems
faulty in that it doesn't consider devices (not controllers) which
don't support link powersaving mode.
Theory never matches reality when it comes to dark allys of cheap
ATA/ATAPI world. It's just unrealistic to expect vendors to test
rarely used link powersaving feature rigorously. This patch makes
ahci more friendly to the coldness of reality.
This shouldn't have any negative effect - when suspend operation
succeeds, we power off the whole machine; otherwise, we wake up
everything. I can't see any reason to be so elaborate with powering
down the link in the first place.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Several people reported issues with certain drive commands timing out on
sata_nv controllers running in ADMA mode. The commands in question were
non-DMA-mapped commands, usually FLUSH CACHE or FLUSH CACHE EXT.
From experimentation it appears that the NV_INT_DEV indication isn't
always set when a legitimate command completion interrupt is received on
a legacy-mode command, at least not on these controllers in ADMA mode.
When a command is pending on the port, force the flag on always in the
irq_stat value before calling nv_host_intr so that the drive busy state
is always checked by ata_host_intr.
This also fixes some questionable code in nv_host_intr which called
ata_check_status when a command was pending and ata_host_intr returned
"unhandled". If the device interrupted at just the wrong time this could
cause interrupts to be lost.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As with JMicron controllers, ULi M5288 sets interface fatal error bit
on device error including ATAPI CC. This makes libata hardreset the
port on ATAPI CC thus making it impossible to use. Ignore interface
fatal error bit on ULi M5288. This fixes bugzilla bug #7837.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch removes kernel 2.4 compatibility code.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With USB2.0 bulk out MTU can be 512 bytes, so checking it only for 64
bytes is incorrect.
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we stop using dev_alloc_skb on the IrDA TX frame, we constantly run
into the case of the skb headroom being 0, and thus we call skb_cow for
every IrDA TX frame.
This patch uses a local buffer and memcpy the skb to it, saving us a
kmalloc for each of those IrDA TX frames.
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are doing ->buf_prepare(buf) before adding buf to q->stream list. This
means that videobuf_qbuf() should not try to re-add a STATE_PREPARED buffer.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Change my email address to reflect OSDL merger.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
[ The irony. Somebody still has his sign-off message hardcoded
in a script or his brainstem ;^]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mv643xx_eth: Fix race condition in mv643xx_eth_free_tx_descs
This bug was found and isolated by Thibaut VARENE <T-Bone@parisc-linux.org>
and Jarek Poplawski <jarkao2@o2.pl>. This patch is a modification of their
fixes. We acquire and release the lock for each descriptor that is freed
to minimize the time the lock is held.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
memset() after kmalloc() on size * 8 would better be on size * 8, not
just size; fixed by switching to kcalloc() - it's more idiomatic anyway.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Fix mismatched spin_unlock in irq handler
IB/ehca: Fix improper use of yield() with spinlock held
IB/srp: Check match_strdup() return
memset() after kmalloc() on size * 8 would better be on size * 8, not
just size; fixed by switching to kcalloc() - it's more idiomatic anyway.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
NetXen: Use pci_register_driver() instead of pci_module_init() in init_module
NetXen: Firmware check modifications
ehea: Fixed possible nullpointer access
ehea: Added logging off associated errors
ehea: Improved logging of permission issues
ehea: New method to determine number of available ports
ehea: Modified initial autoneg state determination
ehea: Fixing firmware queue config issue
ehea: Fixed wrong dereferencation
PHY: Export phy ethtool helpers
modify 3c589_cs to be SMP safe
Seems to be some left-over debug code.
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following patch fixes a few problems with the tlclk driver.
* bug in the select_amcb1_transmit_clock
* racy read sys call
* racy open sys call
* use of add_timer where mod_timer would be better
* change to the timer data parameter use
Signed-off-by: Mark Gross <mark.gross@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes the SH rtc driver correctly act on the "enabled" flag when
setting an alarm.
Signed-off-by: Jamie Lenehan <lenehan@twibble.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a page is marked as dirty in the guest pte, set_pte_common() can set the
writable bit on newly-instantiated shadow pte. This optimization avoids
a write fault after the initial read fault.
However, if a write fault instantiates the pte, fix_write_pf() incorrectly
reports the fault as a guest page fault, and the guest oopses on what appears
to be a correctly-mapped page.
Fix is to detect the condition and only report a guest page fault on a user
access to a kernel page.
With the fix, a kvm guest can survive a whole night of running the kernel
hacker's screensaver (make -j9 in a loop).
Signed-off-by: Avi Kivity <avi@qumranet.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The various bit string instructions (bts, btc, etc.) fail to adjust the
address correctly if the bit address is beyond BITS_PER_LONG.
This bug creeped in as the emulator originally relied on cr2 to contain the
memory address; however we now decode it from the mod r/m bits, and must
adjust the offset to account for large bit indices.
The patch is rather large because it switches src and dst decoding around, so
that the bit index is available when decoding the memory address.
This fixes workloads like the FC5 installer.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kvm mmio read path looks like:
1. guest read faults
2. kvm emulates read, calls emulator_read_emulated()
3. fails as a read requires userspace help
4. exit to userspace
5. userspace emulates read, kvm sets vcpu->mmio_read_completed
6. re-enter guest, fault again
7. kvm emulates read, calls emulator_read_emulated()
8. succeeds as vcpu->mmio_read_emulated is set
9. instruction completes and guest is resumed
A problem surfaces if the userspace exit (step 5) also requests an interrupt
injection. In that case, the guest does not re-execute the original
instruction, but the interrupt handler. The next time an mmio read is
exectued (likely for a different address), step 3 will find
vcpu->mmio_read_completed set and return the value read for the original
instruction.
The problem manifested itself in a few annoying ways:
- little squares appear randomly on console when switching virtual terminals
- ne2000 fails under nfs read load
- rtl8139 complains about "pci errors" even though the device model is
incapable of issuing them.
Fix by skipping interrupt injection if an mmio read is pending.
A better fix is to avoid re-entry into the guest, and re-emulating immediately
instead. However that's a bit more complex.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes the vmwrite errors on vm shutdown go away.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This will use pci_register_driver() instead of pci_module_init().
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch is to make the driver work with multiple minor firmware versions
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fixed possible nullpointer access in event queue processing
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Added logging of error events associated with a specific queue pair
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Disabled dump of hcall regs on some permission issues and
fixed appropriate misleading logmessages
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Count OFDT nodes to determine the number of available ports
instead of using the possibly outdated value from the hypervisor
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Logical partitions are not allowed to (try to) set the autonegotiation status.
This patch removes the respective function call from the port setup function.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix to use exactly one queue for incoming packets in all
firmware configurations
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Not only check the pointer against 0 but also the dereferenced value
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We need to export phy_ethtool_gset and phy_ethtool_sset to allow drivers that
use these functions to be built as modules.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
1. EL3WINDOW is always 1 when lock is not held.
2. The second argument of el3_interrupt is 'void *dev_id',
not 'struct el3_private *lp'.
Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Both "=r" and "=g" breaks my build on i386:
$ make
CC [M] drivers/kvm/vmx.o
{standard input}: Assembler messages:
{standard input}:3318: Error: bad register name `%sil'
make[1]: *** [drivers/kvm/vmx.o] Error 1
make: *** [_module_drivers/kvm] Error 2
The reason is that setbe requires an 8-bit register but "=r" does not
constrain the target register to be one that has an 8-bit version on
i386.
According to
http://gcc.gnu.org/bugzilla/show_bug.cgi?id=10153
the correct constraint is "=q".
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
