This patch adds a new SERIO driver to support the Altera University
Program PS/2 controller.
[dtor@mail.ru: assorted cleanups]
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This small snippet escaped last round of int -> bool conversion.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Sometimes it is not clear why IRQ delivery test failed so let's
add some debug printks so we know the exact reason.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
libps2 can not be built in if i8042 is a module, all other combinations
are allowed.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The serio ports on i8042 are not completely isolated; while we provide
enough locking to ensure proper serialization when accessing control
and data registers AUX and KBD ports can still have an effect on each
other on PS/2 protocol level. The most prominent effect is that
issuing a command for the device connected to one port may cause
abort of the command currently executing by the device connected to
another port.
Since i8042 nor serio subsystem are not aware of the details of the
PS/2 protocol (length of the commands and their replies and so on) the
locking should be done on libps2 level by adding special handling when
we see that we are dealing with serio port on i8042.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
i8042 is not hot-pluggable and we create the device when we register
the driver, so let's save some memory by using platform_device_probe
and using __init instead of __devinit.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Ever since we switched from having a polling timer to registering IRQ
handlers for both keyboard and AUX ports at the driver registration
time, on certain boxes probing for a mouse results in keyboard
stopping working. The only real difference between old and new way is
that before we disabled ports after unsuccessful probe whereas now we
leave them as is. Try to emulate the old behavior by disabling and
immediately re-enabling AUX and KBD ports when corresponding serio
port is being closed.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It seems that many laptops do not fully implement AUX LOOP command in
their keyboard controllers, causing issues with touchpad detection.
We know however that almost every laptop/portable uses a PS/2 pointing
device and, even if user disables it in favor of an external mouse,
the system will not use IRQ 12 for anything else. Therefore we may
bypass AUX IRQ delivery test when running on a laptop and assume that
it is routed properly.
Just to be safe we require the box to have good PNP data in order to
bypass the test.
[Jin Dongming <jin.dongming@np.css.fujitsu.com>: fix crash caused
by missing terminator in the DMI table]
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When KBC is in active multiplexing mode, disabling and re-enabling the
touchpad with the special key leaves the touchpad dead. Since the laptop
does not have any external PS/2 ports disabling MUX mode should be safe.
Reported-by: Eugeniy Meshcheryakov <eugen@debian.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is the driver for Sentelic Finger Sensing Pad which can be found
on MSI WIND Netbook.
Signed-off-by: Tai-hwa Liang <avatar@sentelic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The synaptic touchpad on the Asus G1S is not properly detected when
rebooting machine or on cold boot from time to time. Adding the Asus
G1S to the noloop exception table resolves the issue.
# dmidecode 2.10
SMBIOS 2.4 present.
Handle 0x0001, DMI type 1, 27 bytes
System Information
Manufacturer: ASUSTeK Computer Inc.
Product Name: G1S
Version: 1.0
Wake-up Type: Power Switch
SKU Number:
Family:
Signed-off-by: Jory A. Pratt <geekypenguin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: gpio_mouse - use standard driver registration method
Input: mark serio and i8042 as suspended when hibernating too
Input: add support for generic GPIO-based matrix keypad
Input: arrange keyboards alphabetically
Input: gpio-keys - avoid possibility of sleeping in timer function
Input: gpio-keys - revert 'change timer to workqueue'
Input: dm355evm_keys - fix kconfig symbol names
Input: wacom - add DTF720a support and fix rotation on Intuos3
Input: i8042 - more reset quirks for MSI Wind-clone netbooks
Use the function resource_size, which reduces the chance of
introducing off-by-one errors in calculating the resource size.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct resource *res;
@@
- (res->end - res->start) + 1
+ resource_size(res)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Serio ports are not being restarted any longer because resume operations
after hibernate do nothing, since the device has not been marked as
suspended. This happens because suspend is only considering the SUSPEND
event but not the FREEZE event.
Note that this driver has still to migrate to dev_pm_ops, but this fixes
this particular bug now.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When testing Moblin on various netbooks, we've got reports that
many MSI Wind clones need the i8042 reset quirks for the keyboard
and/or touchpad's proper function.
Signed-off-by: Yan Li <yan.i.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (35 commits)
Input: add driver for Synaptics I2C touchpad
Input: synaptics - add support for reporting x/y resolution
Input: ALPS - handle touchpoints buttons correctly
Input: gpio-keys - change timer to workqueue
Input: ads7846 - pin change interrupt support
Input: add support for touchscreen on W90P910 ARM platform
Input: appletouch - improve finger detection
Input: wacom - clear Intuos4 wheel data when finger leaves proximity
Input: ucb1400 - move static function from header into core
Input: add driver for EETI touchpanels
Input: ads7846 - more detailed model name in sysfs
Input: ads7846 - support swapping x and y axes
Input: ati_remote2 - use non-atomic bitops
Input: introduce lm8323 keypad driver
Input: psmouse - ESD workaround fix for OLPC XO touchpad
Input: tsc2007 - make sure platform provides get_pendown_state()
Input: uinput - flush all pending ff effects before destroying device
Input: simplify name handling for certain input handles
Input: serio - do not use deprecated dev.power.power_state
Input: wacom - add support for Intuos4 tablets
...
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
MAINTAINERS: EB110ATX is not ebsa110
MAINTAINERS: update Eric Miao's email address and status
fb: add support of LCD display controller on pxa168/910 (base layer)
[ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
[ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
[ARM] 5544/1: Trust PrimeCell resource sizes
[ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
[ARM] pxa/sharpsl_pm: drop set_irq_type calls
[ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
[ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
[ARM] sa1100: remove unused collie_pm.c
[ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
[ARM] 5550/1: Add default configure file for w90p910 platform
[ARM] 5549/1: Add clock api for w90p910 platform.
[ARM] 5548/1: Add gpio api for w90p910 platform
[ARM] 5551/1: Add multi-function pin api for w90p910 platform.
[ARM] Make ARM_VIC_NR depend on ARM_VIC
[ARM] 5546/1: ARM PL022 SSP/SPI driver v3
ARM: OMAP4: SMP: Update defconfig for OMAP4430
ARM: OMAP4: SMP: Enable SMP support for OMAP4430
...
I found the PrimeCell/AMBA Bus drivers distrusting the resource
passed in as part of the struct amba_device abstraction. This
patch removes all hard coded resource sizes found in the PrimeCell
drivers and move the responsibility of this definition back to
the platform/board device definition, which already exist and
appear to be correct for all in-tree users of these drivers.
We do this using the resource_size() inline function which was
also replicated in the only driver using the resource size, so
that has been changed too. The KMI_SIZE was left in kmi.h in case
someone likes it. Test-compiled against Versatile and Integrator
defconfigs, seems to work but I don't posess these boards and
cannot test them.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: libps2 - better handle bad scheduler decisions
Input: usb1400_ts - fix access to "device data" in resume function
Input: multitouch - augment event semantics documentation
Input: multitouch - add tracking ID to the protocol
Sometimes devices send us their responses in time but due to
unfortunate scheduling decisions the receiving thread does not
get scheduled till much later and we erroneously decide that
device timed out. Work around this problem by checking whether we
received the data we needed instead of checking timeout
condition.
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The second argument of the probe method points to the amba_id
structure, so it's better passed with the correct type. None of the
current in-tree drivers uses the pointer, so they have only been
checked for a clean compile.
Change suggested by Russell King.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: document the multi-touch (MT) protocol
Input: add detailed multi-touch finger data report protocol
Input: allow certain EV_ABS events to bypass all filtering
Input: bcm5974 - add documentation for the driver
Input: bcm5974 - augment debug information
Input: bcm5974 - Add support for the Macbook 5 (Unibody)
Input: bcm5974 - add quad-finger tapping
Input: bcm5974 - prepare for a new trackpad header type
Input: appletouch - fix DMA to/from stack buffer
Input: wacom - fix TabletPC touch bug
Input: lifebook - add DMI entry for Fujitsu B-2130
Input: ALPS - add signature for Toshiba Satellite Pro M10
Input: elantech - make sure touchpad is really in absolute mode
Input: elantech - provide a workaround for jumpy cursor on firmware 2.34
Input: ucb1400 - use disable_irq_nosync() in irq handler
Input: tsc2007 - use disable_irq_nosync() in irq handler
Input: sa1111ps2 - use disable_irq_nosync() in irq handlers
Input: omap-keypad - use disable_irq_nosync() in irq handler
On parisc machines, which don't have HIL, removing the hp_sdc module
panics the kernel. Fix this by returning early in hp_sdc_exit() if no HP
SDC controller was found.
Add functionality to probe for the hp_sdc_mlc kernel module (which takes
care of the upper layer HIL functionality on parisc) after two seconds.
This is needed to get all the other HIL drivers (keyboard / mouse/ ..)
drivers automatically loaded by udev later as well.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Frans Pop <elendil@planet.nl>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Grant Grundler <grundler@parisc-linux.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
disable_irq() waits for all running handlers to complete before
returning. As such, if it's used to disable an interrupt from
that interrupt's handler it will deadlock. This replaces the
dangerous instances with the _nosync() variant which doesn't have
this problem.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Current style calls for placing EXPORT_SYMBOL() markings directly
after exported symbol definition; let's follow it.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There are several DMI tables in the i8042 (keyboard) driver already, but
not one for the i8042.reset option. This patch adds such an option.
Two users for this table are added as well, the MSI Wind U-100 and the LG
X110. The MSI Wind also needs to be in the "don't trust the pnp data" for
the touchpad to work on my machine.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some touchpads don't reset right the first time (MSI Wind U-100 for
example). This patch will retry the reset up to 5 times.
In addition, on x86, we don't fail entire i8042 initialization if
controller reset fails in hope that keyboard port will still be
functional and user will still get a working keyboard. This is
especially important on netbooks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Most fasync implementations do something like:
return fasync_helper(...);
But fasync_helper() will return a positive value at times - a feature used
in at least one place. Thus, a number of other drivers do:
err = fasync_helper(...);
if (err < 0)
return err;
return 0;
In the interests of consistency and more concise code, it makes sense to
map positive return values onto zero where ->fasync() is called.
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - touchpad driver miss-recognising logitech mice
Input: synaptics - ensure we reset the device on resume
Input: usbtouchscreen - fix eGalax HID ignoring
Input: ambakmi - fix timeout handling in amba_kmi_write()
Input: pxa930_trkball - fix write timeout handling
Input: struct device - replace bus_id with dev_name(), dev_set_name()
Input: bf54x-keys - fix debounce time validation
Input: spitzkbd - mark probe function as __devinit
Input: omap-keypad - mark probe function as __devinit
Input: corgi_ts - mark probe function as __devinit
Input: corgikbd - mark probe function as __devinit
Input: uvc - the button on the camera is KEY_CAMERA
Input: psmouse - make MOUSE_PS2_LIFEBOOK depend on X86
Input: atkbd - make forced_release_keys[] static
Input: usbtouchscreen - allow reporting calibrated data
With a postfix decrement timeleft reaches -1 rather than 0,
but after the loop it is tested to have become 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (29 commits)
Input: i8042 - add Dell Vostro 1510 to nomux list
Input: gtco - use USB endpoint API
Input: add support for Maple controller as a joystick
Input: atkbd - broaden the Dell DMI signatures
Input: HIL drivers - add MODULE_ALIAS()
Input: map_to_7segment.h - convert to __inline__ for userspace
Input: add support for enhanced rotary controller on pxa930 and pxa935
Input: add support for trackball on pxa930 and pxa935
Input: add da9034 touchscreen support
Input: ads7846 - strict_strtoul takes unsigned long
Input: make some variables and functions static
Input: add tsc2007 based touchscreen driver
Input: psmouse - add module parameters to control OLPC touchpad delays
Input: i8042 - add Gigabyte M912 netbook to noloop exception table
Input: atkbd - Samsung NC10 key repeat fix
Input: atkbd - add keyboard quirk for HP Pavilion ZV6100 laptop
Input: libps2 - handle 0xfc responses from devices
Input: add support for Wacom W8001 penabled serial touchscreen
Input: synaptics - report multi-taps only if supported by the device
Input: add joystick driver for Walkera WK-0701 RC transmitter
...
Add MODULE_ALIAS() to the HIL keyboard (hil_kbd.c) and HIL mouse
(hil_ptr.c) drivers to make kernel module autoloader functional.
Report HIL port number ID in serio id.id field.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - add support for new USB Tablet PCs
Input: replace spin_lock_bh with spin_lock_irqsave in ml_ff_playback
Input: i8042 - add Compal Hel80 laptop to nomux blacklist
Input: cm109 - add keymap for ATCom AU-100 phone
Input: fix the example of an input device driver
Input: psmouse - fix incorrect validate_byte check in OLPC protocol
Input: atkbd - cancel delayed work before freeing its structure
Input: atkbd - add keymap quirk for Inventec Symphony systems
Input: i8042 - add Dell XPS M1530 to nomux list
Input: elo - fix format string in elo driver
The CLPS7500 platform has not built since 2.6.22-git7 and there
seems to be no interest in fixing it. So, remove the platform
support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dell XPS M1530 needs i8042.nomux=1 for ALPS touchpad to work as
reported on https://qa.mandriva.com/show_bug.cgi?id=43532
It is said that before A08 bios version this isn't needed (I don't
have the hardware so can't check), and suppose this will not break
with bios versions before A08.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Andreas Ericsson <ae@op5.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
As it is, all instances of ->release() for files that have ->fasync()
need to remember to evict file from fasync lists; forgetting that
creates a hole and we actually have a bunch that *does* forget.
So let's keep our lives simple - let __fput() check FASYNC in
file->f_flags and call ->fasync() there if it's been set. And lose that
crap in ->release() instances - leaving it there is still valid, but we
don't have to bother anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Review comments were incorporated to improve the driver.
1. Some data was eliminated that was not needed.
2. Renaming of variables for clarity.
3. Removed unneeded type casting.
4. Changed to use dev_err rather than other I/O.
5. Merged together some functions.
6. Added kerneldoc format to functions.
Signed-off-by: Sadanand <sadanan@xilinx.com>
Signed-off-by: John Linn <john.linn@xilinx.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: psmouse - add support for Elantech touchpads
Input: i8042 - add Blue FB5601 to noloop exception table
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (32 commits)
Input: wm97xx - update email address for Liam Girdwood
Input: i8042 - add Thinkpad R31 to nomux list
Input: move map_to_7segment.h to include/linux
Input: ads7846 - fix cache line sharing issue
Input: cm109 - add missing newlines to messages
Input: document i8042.debug in kernel-parameters.txt
Input: keyboard - fix potential out of bound access to key_map
Input: psmouse - add OLPC touchpad driver
Input: psmouse - tweak PSMOUSE_DEFINE_ATTR to support raw set callbacks
Input: psmouse - add psmouse_queue_work() for ps/2 extension to make use of
Input: psmouse - export psmouse_set_state for ps/2 extensions to use
Input: ads7846 - introduce .gpio_pendown to get pendown state
Input: ALPS - add signature for DualPoint found in Dell Latitude E6500
Input: serio_raw - allow attaching to translated (SERIO_I8042XL) ports
Input: cm109 - don't use obsolete logging macros
Input: atkbd - expand Latitude's force release quirk to other Dells
Input: bf54x-keys - add power management support
Input: atmel_tsadcc - improve accuracy
Input: convert drivers to use strict_strtoul()
Input: appletouch - handle geyser 3/4 status bits
...
Kill compiler warnings related to printf() formats in the input drivers for
various HP9000 machines, which are shared between PA-RISC (suseconds_t is int)
and m68k (suseconds_t is long). As both are 32-bit, it's safe to cast to int.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thinkpad R31 needs i8042 nomux quirk. Stops jittery jumping mouse
and random keyboard input. Fixes kernel bug #11723. Cherry picked
from Ubuntu who have sometimes (on-again-off-again) had a fix in
their patched kernels.
Signed-off-by: Colin B Macdonald <cbm@m.fsf.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Now that arch/ppc is dead CONFIG_PPC_MERGE is always defined for all
powerpc platforms and we want to get rid of CONFIG_PPC_MERGE use
CONFIG_PPC instead.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
serio_raw only binds to non-translated devices. Enable serio_raw to
bind to normal (translated) keyboards which can have non-standard
extensions (like POS Keyboards). With this it is possible to send
commands to the device over /dev/serio_raw<n>.
Signed-off-by: Niels de Vos <niels.devos@wincor-nixdorf.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Apparently, there are more different versions of Lenovo 3000 N100, some
of them working properly with active mux, and some of them requiring it
being switched off.
This patch applies 'nomux' only to the specific product name that is
reported to behave badly unless 'nomux' is specified.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xilinx_ps2 - fix warning
Input: bcm5974 - implement autosuspend support
Input: bcm5974 - add driver for Macbook Air and Pro Penryn touchpads
Input: paper over a bug in Synaptics X driver
Input: evdev - split EVIOCGBIT handlig into a separate function
Input: i8042 - Add Dritek quirk for Acer TravelMate 4280
Input: xpad - add Pelican Eclipse D-Pad to the list of devices
Input: gpio-keys - make gpio_keys_device_driver static
Input: gpio-keys - fix possible NULL pointer dereference
Input: wm97xx - enable sub-drivers by default
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Handle stack trace attempts before irqstacks are setup.
sparc64: Implement IRQ stacks.
sparc: remove include of linux/of_device.h from asm/of_device.h
sparc64: Fix recursion in stack overflow detection handling.
sparc/drivers: use linux/of_device.h instead of asm/of_device.h
sparc64: Don't MAGIC_SYSRQ ifdef smp_fetch_global_regs and support code.
drivers/input/serio/xilinx_ps2.c:272: warning: cast from pointer
to integer of different size
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus-merged' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5177/1: arm/mach-sa1100/Makefile: remove CONFIG_SA1100_USB
[ARM] 5166/1: magician: add MAINTAINERS entry
[ARM] fix pnx4008 build errors
[ARM] Fix SMP booting with non-zero PHYS_OFFSET
[ARM] 5185/1: Fix spi num_chipselect for lubbock
[ARM] Move include/asm-arm/arch-* to arch/arm/*/include/mach
[ARM] Add support for arch/arm/mach-*/include and arch/arm/plat-*/include
[ARM] Remove asm/hardware.h, use asm/arch/hardware.h instead
[ARM] Eliminate useless includes of asm/mach-types.h
[ARM] Fix circular include dependency with IRQ headers
avr32: Use <mach/foo.h> instead of <asm/arch/foo.h>
avr32: Introduce arch/avr32/mach-*/include/mach
avr32: Move include/asm-avr32 to arch/avr32/include/asm
[ARM] sa1100_wdt: use reset_status to remember watchdog reset status
[ARM] pxa: introduce reset_status and clear_reset_status for driver's usage
[ARM] pxa: introduce reset.h for reset specific header information
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
drivers/input/serio/i8042-sparcio.h:95: warning: 'sparc_i8042_driver'
defined but not used
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both commits 0f17e4c796 ("Add missing
semaphore.h includes") and 4933d07531
("m68k: drivers/input/serio/hp_sdc.c needs <linux/semaphore.h>") added a
We only really need one ;)
Reported-by: Huang Weiyi <weiyi.huang@gmail.com>
Requested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These files use semaphores but don't include semaphore.h
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
When resuming AUX ports psmouse driver calls psmouse_extensions()
to determine if the attached mouse is still the same, which may take
a while to complete for generic mice. Offload the resume process to
kseriod so the rest of the system may continue resuming without
waiting for the mouse.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Move the line disciplines towards a conventional ->ops arrangement. For
the moment the actual 'tty_ldisc' struct in the tty is kept as part of
the tty struct but this can then be changed if it turns out that when it
all settles down we want to refcount ldiscs separately to the tty.
Pull the ldisc code out of /proc and put it with our ldisc code.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The board does not raise AUX IRQ in response to AUX LOOP command.
Reported-by: Guillaume Morin <guillaume@morinfr.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add "no_hpsdc" kernel module option to the hp_sdc driver, so that
the driver can be instructed to not enable the HP SDC port.
This is useful on some older HPPA boxes with HIL keyboard
and HIL mouse where the new HP SDC HIL drivers don't work
yet. By disabling the new hp_sdc driver users are able to use
the older hilkbd driver instead.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Added a new driver for Xilinx XPS PS2 IP. This driver is
a flat driver to better match the Linux driver pattern.
Signed-off-by: Sadanand <sadanan@xilinx.com>
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Acer Aspire 5720 series also requires the Dritek quirk
to enable the extra scancodes.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Gericom Bellagio needs to be added to nomux blacklist, otherwise its
touchpad misbehaves.
Reported-by: Roland Kletzing <roland.kletzing@materna.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch makes the needlessly global struct hp_sdc_mlc_priv_s static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There are systems that fail in i8042_resume() with
i8042: Can't write CTR to resume
as i8042_command(&i8042_ctr, I8042_CMD_CTL_WCTR) fails even though the
controller claimed itself to be ready before.
One retry after failing write fixes the problems on the failing systems.
Reported-by: Helmut Schaa <hschaa@novell.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fujitsu Siemens Amilo Pro V2030 needs nomux table entry, in addition to
already existing entry for V2010 model (note that Fujitsu-Siemens changed
the capitalization in the DMI data for product).
Tested-by: Jiri Mleziva <jmleziva@tiscali.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
That fixes an opps when driver is repeatedly loaded and unloaded in
a tight loop.
Tested-by: Roland Kletzing <devzero@web.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch introduces i8042_dmi_nopnp_table to make it possible to perform
DMI matches for systems that need 'i8042.nopnp' to work correctly, and
introduces such an entry for Intel D845PESV -- this system doesn't
detect PS2 mouse reliably without this option, as reported by Robert
Lewis.
[dtor@mail.ru - make it compile if CONFIG_PNP is off - reported
by Randy Dunlap]
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
According to the tests in do_initcalls(), the proper error code in case no
device is found is -ENODEV, not -ENXIO or -EIO.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some input drivers do not check whether they're actually running on the
correct platform, causing multi-platform kernels to crash if they are not.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Delayed command execution is not used by anyone so let's remove it.
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
drivers/input/serio/hp_sdc.c: In function 'hp_sdc_take':
drivers/input/serio/hp_sdc.c:198: error: implicit declaration of function 'up'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Operations are now a shared const function block as with most other Linux
objects
- Introduce wrappers for some optional functions to get consistent behaviour
- Wrap put_char which used to be patched by the tty layer
- Document which functions are needed/optional
- Make put_char report success/fail
- Cache the driver->ops pointer in the tty as tty->ops
- Remove various surplus lock calls we no longer need
- Remove proc_write method as noted by Alexey Dobriyan
- Introduce some missing sanity checks where certain driver/ldisc
combinations would oops as they didn't check needed methods were present
[akpm@linux-foundation.org: fix fs/compat_ioctl.c build]
[akpm@linux-foundation.org: fix isicom]
[akpm@linux-foundation.org: fix arch/ia64/hp/sim/simserial.c build]
[akpm@linux-foundation.org: fix kgdb]
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix incorrect length argument for strncpy and strncat by replacing them with
strlcpy and strlcat
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since 43cc71eed1, the platform modalias
is prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable
"input" platform drivers, to re-enable auto loading.
[dbrownell@users.sourceforge.net: more drivers, registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add support for the PSIF peripheral on AVR32 AP7 devices. It is implemented
as a serio driver and will behave like a serio 8042 device.
The driver has been tested with a Dell keyboard capable of running on 3.3
volts and a Logitech mouse on the STK1000 + STK1002 starter kit. The Logitech
mouse was hacked by cutting the cord and using a bi-directional voltage
converter to get the required 5 volt I/O level.
For more information about the PSIF module, see the datasheet for AT32AP700X at
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
SNI RM200 don't have the i8042 controller connected to the EISA bus,
but have a second address range for onboard devices. This patch handles
the two possible address ranges for the i8042 on SNI RMs.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit c18bab80 ("Input: i8042 - non-x86 build fix") introduced the
following warning on non-x86 builds:
drivers/input/serio/i8042.c: In function 'i8042_probe':
drivers/input/serio/i8042.c:1154: warning: unused variable 'param'
Fix this by moving the parameter variable declaration into the #ifdef too.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If firmware does not implement AUX_LOOP comand in 32 bit mode it
is unlikely to implement it in 64 bit mode. Same goes for active
multiplexing. See:
http://bugzilla.kernel.org/show_bug.cgi?id=9664
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The Acer Aspire 9110 series also requires the Dritek quirk to enable the
extra scancodes.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some Wistron based laptops need us to explicitly enable the 'Dritek
keyboard extension' to make their extra keys start generating scancodes.
Originally, this was just confined to older laptops, but a few Acer
laptops have turned up in 2007 that also need this again.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Drop #include <linux/moduleparam.h> in files that also include
linux/module.h, since module.h includes moduleparam.h already.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
RT guys advised me that in their kernels synchronize_sched() will not
work to ensure that all IRQ handlers run to their completion and that
synchronize_irq() should be used instead.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: adds the context menu key (HUT GenDesc 0x84)
Input: add definitions for frame forward and frame back keys
Input: bf54x-keys - keypad does not exist on BF544 parts
Input: gpio-keys - request and configure GPIOs
Input: i8042 - add i8042.noloop quirk for MS Virtual Machine
Sonypi: use synchronize_irq instead of sycnronize_sched
sonypi: fit input devices into sysfs tree
sony-laptop: fit input devices into sysfs tree
When booting under Microsoft Virtual Machine, the noloop quirk is
needed, otherwise PS/2 mouse is not properly detected.
Reported-by: Lawrence Steeger <vendor@russte.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
hp_sdc_exit() mustn't be __exit since it's called from the
__init hp_sdc_register().
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
None of the drivers with a struct pardevice's ->irq_func() hook ever
used the 'irq' argument passed to it, so remove it.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
define global BIT macro
move all local BIT defines to the new globally define macro.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get rid of input BIT* duplicate defines
use newly global defined macros for input layer. Also remove includes of
input.h from non-input sources only for BIT macro definiton. Define the
macro temporarily in local manner, all those local definitons will be
removed further in this patchset (to not break bisecting).
BIT macro will be globally defined (1<<x)
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: <dtor@mail.ru>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Cc: <lenb@kernel.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: <perex@suse.cz>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <vernux@us.ibm.com>
Cc: <malattia@linux.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce freezer-friendly wrappers around wait_event_interruptible() and
wait_event_interruptible_timeout(), originally defined in <linux/wait.h>, to
be used in freezable kernel threads. Make some of the freezable kernel
threads use them.
This is necessary for the freezer to stop sending signals to kernel threads,
which is implemented in the next patch.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This changes the uevent buffer functions to use a struct instead of a
long list of parameters. It does no longer require the caller to do the
proper buffer termination and size accounting, which is currently wrong
in some places. It fixes a known bug where parts of the uevent
environment are overwritten because of wrong index calculations.
Many thanks to Mathieu Desnoyers for finding bugs and improving the
error handling.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes "atkbd.c: Suprious NAK on isa0060/serio0" errors for
HP Pavilion DV4270ca.
Signed-off-by: Elvis Pranskevichus <el@prans.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
i8042_unregister_ports's only caller i8042_remove is a __devexit function
so make it __devexit too.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We should not return IRQ_HANDLED if we didn't handle the interrupt.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When enabling interrupts for a port fails, the interrupt enable and
port enable bits remain set in i8042_ctr. Later writes of i8042_ctr
to the hardware could accidentally retry enabling interrupts. Clear
the bits on failure.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On some boxes that don't have PS/2 mice connected at startup BIOS
completely disables AUX port and attempts to access it result in
hosed keyboard. Historically we do not trust ACPI/PNP data on
i386 and try to poke AUX port even if we did not find an active
PNP node for it. However in cases when BIOS writers got KBD port
properly described we can assume that they did the right thing
for AUX port as well.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Currently, the freezer treats all tasks as freezable, except for the kernel
threads that explicitly set the PF_NOFREEZE flag for themselves. This
approach is problematic, since it requires every kernel thread to either
set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't
care for the freezing of tasks at all.
It seems better to only require the kernel threads that want to or need to
be frozen to use some freezer-related code and to remove any
freezer-related code from the other (nonfreezable) kernel threads, which is
done in this patch.
The patch causes all kernel threads to be nonfreezable by default (ie. to
have PF_NOFREEZE set by default) and introduces the set_freezable()
function that should be called by the freezable kernel threads in order to
unset PF_NOFREEZE. It also makes all of the currently freezable kernel
threads call set_freezable(), so it shouldn't cause any (intentional)
change of behaviour to appear. Additionally, it updates documentation to
describe the freezing of tasks more accurately.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: appletouch - improve powersaving for Geyser3 devices
Input: lifebook - fix an oops on Panasonic CF-18
Input: document intended meaning of KEY_SWITCHVIDEOMODE
Input: switch to using seq_list_xxx helpers
Input: i8042 - give more trust to PNP data on i386
Input: add driver for Fujitsu serial touchscreens
Input: ads7846 - re-check pendown status before reporting events
Input: ads7846 - introduce sample settling delay
Input: xpad - add support for leds on xbox 360 pad
Transform some calls to kmalloc/memset to a single kzalloc (or kcalloc).
Here is a short excerpt of the semantic patch performing
this transformation:
@@
type T2;
expression x;
identifier f,fld;
expression E;
expression E1,E2;
expression e1,e2,e3,y;
statement S;
@@
x =
- kmalloc
+ kzalloc
(E1,E2)
... when != \(x->fld=E;\|y=f(...,x,...);\|f(...,x,...);\|x=E;\|while(...) S\|for(e1;e2;e3) S\)
- memset((T2)x,0,E1);
@@
expression E1,E2,E3;
@@
- kzalloc(E1 * E2,E3)
+ kcalloc(E1,E2,E3)
[akpm@linux-foundation.org: get kcalloc args the right way around]
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg KH <greg@kroah.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/input/serio/serio_raw.c: In function 'serio_raw_read':
drivers/input/serio/serio_raw.c:163: warning: 'c' may be used uninitialized in this function
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: document some of keycodes
Input: add a new EV_SW SW_RADIO event, for radio switches on laptops
Input: serio - take drv_mutex in serio_cleanup()
Input: atkbd - use printk_ratelimit for spurious ACK messages
Input: atkbd - throttle LED switching
Input: i8042 - add HP Pavilion ZT1000 to the MUX blacklist
We need to take serio->drv_mutex in serio_cleanup() to prevent the
function from being called while driver is in the middle of attaching
to a serio port. Such situation can happen with i8042 and atkbd drivers
if user rapidly presses Ctrl-Alt-Del during system startup, and leads
to kernel oops.
Reported-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This should get rid of "atkbd.c: Suprious NAK on isa0060/serio0"
messages caused by broken MUX implementation. The box does not
have external PS/2 ports and, according to documentation,
automatically disables touchpad when an external mouse is plugged
into a port replicator, so MUX mode would not work anyway.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: move input-polldev to drivers/input
Input: i8042 - add ULI EV4873 to noloop list
Input: i8042 - add ASUS P65UP5 to the noloop list
Input: usbtouchscreen - fix fallout caused by move from drivers/usb
The box does not implement AUX LOOP command properly and so we
can't test for AUX IRQ delivery so blacklist it via DMI and
assume that AUX port is present.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This board does not raise AUX IRQ in response to AUX LOOP command
which interferes with our test for proper AUX IRQ wiring. Put it
in the blacklist and assume mouse is present.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The i8042 driver fails detection of the AUX port with some chips,
because they apparently do not change the I8042_CTR_AUXDIS bit
immediately. This is known to affect at least HP500/HP510 notebooks,
consequently the built-in touchpad will not work. The patch will simply
reread the value until it gets the expected value or a retry limit is
hit, without touching other workaround code in the same area.
Signed-off-by: Roland Scheidegger <sroland@tungstengraphics.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The subsystem rwsem is not used by the driver core at all, so there is
no point in trying to access it.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is no data coming from touchscreen on Panasonic CF-29
notebook unless keyboard controller is in legacy mode.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Disable both keyboard and auxiliary interfaces before switching
to legacy mode to prevent atkbd from getting "empty" interrupts.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This should get rid of "atkbd.c: Suprious NAK on isa0060/serio0"
messages caused by broken MUX implementation. The box does not
have external PS/2 ports so disabling MUX mode is safe.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not assume that AUX_LOOP command is broken unless it
completes successfully but returns wrong (unexpected) data.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
- mark some structures const or __read_mostly
- hilkbd.c: fix uninitialized spinlock in HIL keyboard driver
- hil_mlc.c: use USEC_PER_SEC instead of 1000000
- hp_sdc: bugfix for request_irq()/free_irq() parameters, this prevented
multiple load/unload cycles as module
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/dtor/input:
Input: remove obsolete setup parameters from input drivers
Input: HIL - fix improper call to release_region()
Input: hid-lgff - treat devices as joysticks unless told otherwise
Input: HID - add support for Logitech Formula Force EX
Input: gpio-keys - switch to common GPIO API
Input: do not lock device when showing name, phys and uniq
Input: i8042 - let serio bus suspend ports
Input: psmouse - properly reset mouse on shutdown/suspend
Let serio subsystem take care of suspending the ports; concentrate
on suspending/resuming the controller itself.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On boxes that do not implement AUX LOOP command we can not
verify AUX IRQ delivery and must assume that it is wired
properly.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This adds the module name to all SERIO drivers, if they are built into
the kernel or not. It will show up in /sys/modules/MODULE_NAME/drivers/
Cc: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On some boxes panic blink procedure manages to send both bytes
to keyboard contoller before getting first ACK so we need to
make i8042_suppress_kbd_ack a counter instead of boolean.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We need to pass in the resource otherwise we cannot
release the region properly. We must know whether it is
an I/O or MEM resource.
Spotted by Eric Brower.
Signed-off-by: David S. Miller <davem@davemloft.net>
We already had entry for Fujitsu Lifebook P7010 in the nomux
blacklist but for some reason Fujitsu decided to fiddle with
DMI data...
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Move process freezing functions from include/linux/sched.h to freezer.h, so
that modifications to the freezer or the kernel configuration don't require
recompiling just about everything.
[akpm@osdl.org: fix ueagle driver]
Signed-off-by: Nigel Cunningham <nigel@suspend2.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
This also ment that some of the misc drivers had to also be fixed
up as they were assuming the device was a class_device.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Perform actual driver registration right in serio_register_driver()
instead of offloading it to kseriod and return proper error code to
callers if driver registration fails.
Note that driver <-> port matching is still done by kseriod to
speed up boot process since probing for PS/2 mice and keyboards
is pretty slow.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Pass the work_struct pointer to the work function rather than context data.
The work function can use container_of() to work out the data.
For the cases where the container of the work_struct may go away the moment the
pending bit is cleared, it is made possible to defer the release of the
structure by deferring the clearing of the pending bit.
To make this work, an extra flag is introduced into the management side of the
work_struct. This governs auto-release of the structure upon execution.
Ordinarily, the work queue executor would release the work_struct for further
scheduling or deallocation by clearing the pending bit prior to jumping to the
work function. This means that, unless the driver makes some guarantee itself
that the work_struct won't go away, the work function may not access anything
else in the work_struct or its container lest they be deallocated.. This is a
problem if the auxiliary data is taken away (as done by the last patch).
However, if the pending bit is *not* cleared before jumping to the work
function, then the work function *may* access the work_struct and its container
with no problems. But then the work function must itself release the
work_struct by calling work_release().
In most cases, automatic release is fine, so this is the default. Special
initiators exist for the non-auto-release case (ending in _NAR).
Signed-Off-By: David Howells <dhowells@redhat.com>
MUX error handling has a workaround for KBCs that get confused which
port data came from and signal MUXERR while data is actually good.
Unfortunately this workaround hurts with KBCs that signal timeouts
as 0xfc (spec says that only 0xfd, 0xfe and 0xff are alowed with
MUXERR) since it causes endless attempts to rescan i8042 serio
ports. The solution is to treat 0xfc as timeout (0xfe).
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Remove call to i8042_interrupt() from i8042_aux_write(). According
to Vojtech it may cause problems with older controllers if it is
called right after real interrupt. Also it is not needed anymore
since we register IRQs early and not waiting for serio ports to
be opened.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Initialize serio_bus structure at compile time instead of at runtime
in serio_init().
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Enable HIL configuration options on HP300
Signed-off-by: Kars de Jong <jongk@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (35 commits)
Input: wistron - add support for Acer TravelMate 2424NWXCi
Input: wistron - fix setting up special buttons
Input: add KEY_BLUETOOTH and KEY_WLAN definitions
Input: add new BUS_VIRTUAL bus type
Input: add driver for stowaway serial keyboards
Input: make input_register_handler() return error codes
Input: remove cruft that was needed for transition to sysfs
Input: fix input module refcounting
Input: constify input core
Input: libps2 - rearrange exports
Input: atkbd - support Microsoft Natural Elite Pro keyboards
Input: i8042 - disable MUX mode on Toshiba Equium A110
Input: i8042 - get rid of polling timer
Input: send key up events at disconnect
Input: constify psmouse driver
Input: i8042 - add Amoi to the MUX blacklist
Input: logips2pp - add sugnature 56 (Cordless MouseMan Wheel), cleanup
Input: add driver for Touchwin serial touchscreens
Input: add driver for Touchright serial touchscreens
Input: add driver for Penmount serial touchscreens
...
ppc can boot one single binary on prep, chrp and pmac boards. ppc64 can
boot one single binary on pseries and G5 boards. pmac has no legacy io,
probing for PC style legacy hardware (or accessing the legacy io area
regulary) may lead to a hard crash:
* add check for parport_pc, exit on pmac. 32bit chrp has no
->check_legacy_ioport, the probe is always called. 64bit chrp has
check_legacy_ioport, check for a "parallel" node
* add check for isapnp, only PReP boards may have real ISA slots. 32bit
PReP will have no ->check_legacy_ioport, the probe is always called.
* update code in i8042_platform_init. Run ->check_legacy_ioport first,
always call request_region. No functional change. Remove whitespace
before i8042_reset init.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Microsoft Natural Elite Pro keyboard produces unisual response to
the GET ID command - single byte 0xaa (normally keyboards produce
2-byte response). Fail GET ID command so atkbd gets a change to
do alternate probe.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When keyboard controller is in active multiplexing mode ALPS touchpad
may get detected twice. Since the box does not have external PS/2
ports simply disabling MUX mode is safe solution.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Remove polling timer that was used to detect keybord/mice hotplug and
register both IRQs right away instead of waiting for a driver to
attach to a port.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
ALPS touchpad on Amoi laptops (Amoi is a vendor in China) is not
detected when keyboard controller is in MUX mode, add to blacklist.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The PS/2 code has a natural device order and there is a one level recursion in
this device order in terms of the cmd_mutex; annotate this explicit recursion
as ok.
Has no effect on non-lockdep kernels.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/input/serio/i8042-sparcio.h:91: error: '__mod_of_device_table' aliased to undefined symbol 'i8042_match'
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
DESC
sparc: resource warning fix
EDESC
From: Andrew Morton <akpm@osdl.org>
sound/sparc/amd7930.c: In function 'amd7930_attach_common':
sound/sparc/amd7930.c:1040: warning: format '%08lx' expects type 'long unsigned int', but argument 5 has type 'resource_size_t'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/devfs-2.6: (22 commits)
[PATCH] devfs: Remove it from the feature_removal.txt file
[PATCH] devfs: Last little devfs cleanups throughout the kernel tree.
[PATCH] devfs: Rename TTY_DRIVER_NO_DEVFS to TTY_DRIVER_DYNAMIC_DEV
[PATCH] devfs: Remove the tty_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the line_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the videodevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the gendisk devfs_name field as it's no longer needed
[PATCH] devfs: Remove the miscdevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the devfs_fs_kernel.h file from the tree
[PATCH] devfs: Remove devfs_remove() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_cdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_bdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_symlink() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_dir() function from the kernel tree
[PATCH] devfs: Remove devfs_*_tape() functions from the kernel tree
[PATCH] devfs: Remove devfs support from the sound subsystem
[PATCH] devfs: Remove devfs support from the ide subsystem.
[PATCH] devfs: Remove devfs support from the serial subsystem
[PATCH] devfs: Remove devfs from the init code
[PATCH] devfs: Remove devfs from the partition code
...
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some people report that we die on some Macs when we are expecting to
catch machine checks after poking at some random I/O address. I'd seen
it happen on my dual G4 with serial ports until we fixed those to use
OF, but now other users are reporting it with i8042.
This expands the use of check_legacy_ioport() to avoid that situation
even on 32-bit kernels.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Addresses in F-space must be accessed uncached on most parisc machines.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Do not assume that pnp_register_driver() returns the number of
devices claimed.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Serio and gameport cores do not depend on other drivers and are
used by code living outside of drivers/input/{gameport|serio}.
Registering them at subsystem level guarantees that they are
fully initialized before anyone tries to use them.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
98kbd{,-io} and 98spkr all went out with PC98 subarch. Remove stale Makefile
entries that remained.
Signed-off-by: Arthur Othieno <apgo@patchbomb.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>