The patch updates the document by adding more information to describe the
DT proporties used by the Freescale Quadspi driver and the childs nodes.
For the child node for SPI NOR flash, we add the required property
("spi-max-frequency"), and refer to spi-nor-flash.txt for the optional
properties.
Signed-off-by: Huang Shijie <b32955@freescale.com>
(cherry picked from commit d7b296f51eb077b0c77580ad63ffd69ce722bf6c)
We need a DT property to store the dummy cycles for DDR Quad read.
This is a common feature for the SPI NOR flash, such as Spansion and Micron
chips.
Add this file to describe this specific SPI NOR flash features which will
be referred by the SPI NOR flash drivers.
Signed-off-by: Huang Shijie <b32955@freescale.com>
(cherry picked from commit dfbe3eb5c7c2c3967c0f1bf32c0279136da7bfce)
Some registers on pfuze3000 will lost after exit from LPSR, need restore them,
otherwise system may reboot with below command after system enter LPSR one time:
root@imx7d_all:~# echo enabled > /sys/class/tty/ttymxc0/power/wakeup
root@imx7d_all:~# echo mem > /sys/power/state
because LDOGCTL not recover as 1. Add 'fsl,lpsr-mode' property to this case,
please add this property if your board support LPSR mode as imx7d-12x12-lpddr3-arm2
board.
Signed-off-by: Robin Gong <b38343@freescale.com>
It's pretty common that on some reference design or validation boards,
one pin could be used by two devices on board, and the pin route is
controlled by a GPIO. So to assert the pin for given device, not only
the pinmux controller in SoC needs to be set up properly but also the
GPIO needs to be pulled up/down.
The patch adds support of a device tree property "pinctrl-assert-gpios"
under client device node. It plays pretty much like a board level pin
multiplexer, and steers the pin route by controlling the GPIOs. When
client device has the property represent in its node, pinctrl device
tree mapping function will firstly pull up/down the GPIOs to assert the
pins for the device at board level.
[shawn.guo: cherry-pick commit e5a718edab82 from imx_3.10.y]
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Starting from IMX6, the flexcan stop mode control bits is SoC specific,
move it out of IP driver and parse it from devicetree.
It's good from maintain perspective and can avoid adding too many SoC
specifi bits in driver but with no IP changes when the IMX SoC series
keep growing.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
(cherry picked from commit 97b99b59c9f09d58ea35f3c0cf58665c20f2e292)
(cherry picked from commit 6355208605715f7cb9ea8c37e29c577785f66898)
Conflicts:
arch/arm/boot/dts/imx6qdl.dtsi
If wakeup is enabled, enter stop mode, else enter disabled mode.
Self wake can only work on stop mode.
For imx6q, the stop request has to be mannually assert on
IOMUX GPR13[28:29] register, we use syscon to control that bit.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
(cherry picked from commit 7f8ef8eeb2bd93d75eb4c970bcaabcfd499d348d)
(cherry picked from commit 496fef522e515488147cce3adcc7f101bb532805)
WiFi driver could call wifi_card_detect function to re-detect card,
this is required by some special WiFi cards like broadcom WiFi.
To use this function, a new property is introduced to indicate a wifi host.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
(cherry picked from commit 74e71dd0aebb9e931f02aefa3dd1990cbe642ae4)
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Conflicts:
Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
Forward imx_3.14.y IPU and display drivers to 4.1 kernel.
This includes IPU core driver, display driver, LDB and HDMI driver.
Signed-off-by: Sandor Yu <R01008@freescale.com>
cherry-pick below patch from v3.14.y:
ENGR00307635-5 ASoC: imx-wm8962: Add non-SSI cpu dai support
The current imx-wm8962 machine driver is designed for SSI as CPU DAI only
while as its name we should make the driver more generic to any other CPU
DAI on i.MX serires -- ESAI, SAI for example.
So this patch makes the driver more general so as to support those non-SSI
cases.
Acked-by: Wang Shengjiu <b02247@freescale.com>
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
(cherry picked from commit b6fca438dde1b4c0bbdee31729871d601f287dc9)
cherry-pick below patch from v3.14.y:
ENGR00277715-3 ASoC: fsl: Add WM8962 jack detecting support
There're two GPIOs connected to the headphone jack and microphone jack,
thus add the states detection.
Reviewed-by: Wang Shengjiu <b02247@freescale.com>
Signed-off-by: Nicolin Chen <b42378@freescale.com>
cherry-pick below patch from imx_3.14.y
ENGR00330403-3: ASoC: fsl: port si476x machine driver from imx_3.10.y
Port si476x machine dirver for i.MX series SoC and binding doc from imx_3.10.y
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
(cherry picked from commit 05a68db09806fe5b0aa927dd94cf69b1b0c0fa5a)
cherry-pick below patch from imx_3.14.y
ENGR00330403-1: ASoC: imx-cs42888: port cs42888 machine driver from imx_3.10.y
Port the cs42888 machine driver from imx_3.10.y and do update according to
new esai driver and asrc driver.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
(cherry picked from commit 7ed3aac83630a38eb397ed92f815a28e07198748)
Implement machine driver for mqs, which use the sai as cpu dai.
sai work on master mode.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
(cherry picked from commit cac9eb41debc6444d753dc936cdf76874260b9e4)
Implement codec driver for mqs. mqs is a very simple IP. which support:
Word length: 16bit.
DAI format: Left-Justified, slave mode.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
(cherry picked from commit 9da6bdd2072b850e9bb910512123eff7d80a0e2f)
If the property "fsl,dma-buffer-size" is present, using the specified buffer size.
Otherwise, using the default audio buffer size.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
(cherry picked from commit bba153dd92a4f58b81c4c26fb3a95c45445c65e0)
This driver implements a reset controller device that toggle a gpio
connected to a reset pin of a peripheral IC. The delay between assertion
and de-assertion of the reset signal can be configured via device tree.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
cherry-pick below patch from v3.14.y:
ENGR00329948-3: dma: imx-sdma: Add hdmi audio support
in sdma
There's a missing script for hdmi audio support in current sdma driver,
thus add it.
This HDMI script doesn't use bd to copy memory like a normal one does
but only to update the memory address for HDMI internal AHB DMA and
then trigger its procedure automatically.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Robin Gong <b38343@freescale.com>
(cherry picked from commit dafddac916a03ae4477e2de7c1b7ad291f956f68)
This patch adds guide for selecting available gadget drivers for otg and EH
compliance tests.
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
(cherry picked from commit 520cac9e4fe938887dd45b5b4df6c8e35e125a59)
(cherry picked from commit 6534fab0bd77be544629ac04d4b8bb677d0a3aec)
Update HNP test procedure as HNP polling is supported.
Signed-off-by: Li Jun <b47624@freescale.com>
(cherry picked from commit 4aac546c4338246b1e55647796badedf6e80bfbe)
It is used to indicate whether we use SoC's usb charger
detection or not. Besides, we add anatop phandle since
we need to use anatop register to do most of charger detect operations.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
The current driver support stop mode by calling machine api.
The patch add dts support to set gpr register for stop request.
After magic pattern comming during system suspend status, system will
be waked up, and irq handler will be running, there have enet register
access. Since all clocks are disabled in suspend, and clocks are enabled
after resume function. But irq handler run before resume function.
For imx7d chip, access register need some clocks enabled, otherwise system
hang. So the patch also disable wake up irq in the suspend, after resume
back enable the irq, which can avoid system hang issue.
Signed-off-by: Fugang Duan <B38611@freescale.com>
(cherry pick and merge from commit: 8da4f80af0913781a4f9d50917c1dd66180e519d)
[ Upstream commit 321cc359d8 ]
We need this new compatibility string as we experienced different behavior
for this 10/100Mbits/s macb interface on this particular SoC.
Backward compatibility is preserved as we keep the alternative strings.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some users are willing to provision huge amounts of memory to be able
to perform reassembly reasonnably well under pressure.
Current memory tracking is using one atomic_t and integers.
Switch to atomic_long_t so that 64bit arches can use more than 2GB,
without any cost for 32bit arches.
Note that this patch avoids an overflow error, if high_thresh was set
to ~2GB, since this test in inet_frag_alloc() was never true :
if (... || frag_mem_limit(nf) > nf->high_thresh)
Tested:
$ echo 16000000000 >/proc/sys/net/ipv4/ipfrag_high_thresh
<frag DDOS>
$ grep FRAG /proc/net/sockstat
FRAG: inuse 14705885 memory 16000002880
$ nstat -n ; sleep 1 ; nstat | grep Reas
IpReasmReqds 3317150 0.0
IpReasmFails 3317112 0.0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 3e67f106f6)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some applications still rely on IP fragmentation, and to be fair linux
reassembly unit is not working under any serious load.
It uses static hash tables of 1024 buckets, and up to 128 items per bucket (!!!)
A work queue is supposed to garbage collect items when host is under memory
pressure, and doing a hash rebuild, changing seed used in hash computations.
This work queue blocks softirqs for up to 25 ms when doing a hash rebuild,
occurring every 5 seconds if host is under fire.
Then there is the problem of sharing this hash table for all netns.
It is time to switch to rhashtables, and allocate one of them per netns
to speedup netns dismantle, since this is a critical metric these days.
Lookup is now using RCU. A followup patch will even remove
the refcount hold/release left from prior implementation and save
a couple of atomic operations.
Before this patch, 16 cpus (16 RX queue NIC) could not handle more
than 1 Mpps frags DDOS.
After the patch, I reach 9 Mpps without any tuning, and can use up to 2GB
of storage for the fragments (exact number depends on frags being evicted
after timeout)
$ grep FRAG /proc/net/sockstat
FRAG: inuse 1966916 memory 2140004608
A followup patch will change the limits for 64bit arches.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Kirill Tkhai <ktkhai@virtuozzo.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Florian Westphal <fw@strlen.de>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Alexander Aring <alex.aring@gmail.com>
Cc: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 648700f76b)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 934193a654 upstream.
Verify that 'depmod' ($DEPMOD) is installed.
This is a partial revert of commit 620c231c7a
("kbuild: do not check for ancient modutils tools").
Also update Documentation/process/changes.rst to refer to
kmod instead of module-init-tools.
Fixes kernel bugzilla #198965:
https://bugzilla.kernel.org/show_bug.cgi?id=198965
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Lucas De Marchi <lucas.de.marchi@gmail.com>
Cc: Michal Marek <michal.lkml@markovi.net>
Cc: Jessica Yu <jeyu@kernel.org>
Cc: Chih-Wei Huang <cwhuang@linux.org.tw>
Cc: stable@vger.kernel.org # any kernel since 2012
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b76a3cff0 upstream
When nested virtualization is in use, VMENTER operations from the nested
hypervisor into the nested guest will always be processed by the bare metal
hypervisor, and KVM's "conditional cache flushes" mode in particular does a
flush on nested vmentry. Therefore, include the "skip L1D flush on
vmentry" bit in KVM's suggested ARCH_CAPABILITIES setting.
Add the relevant Documentation.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 801e459a6f upstream
Provide a new KVM capability that allows bits within MSRs to be recognized
as features. Two new ioctls are added to the /dev/kvm ioctl routine to
retrieve the list of these MSRs and then retrieve their values. A kvm_x86_ops
callback is used to determine support for the listed MSR-based features.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[Tweaked documentation. - Radim]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5833113613 upstream
Dave reported, that it's not confirmed that Yonah processors are
unaffected. Remove them from the list.
Reported-by: ave Hansen <dave.hansen@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1949f9f497 upstream
Fix spelling and other typos
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ec8ce5d86 upstream
Add documentation for the L1TF vulnerability and the mitigation mechanisms:
- Explain the problem and risks
- Document the mitigation mechanisms
- Document the command line controls
- Document the sysfs files
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lkml.kernel.org/r/20180713142323.287429944@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d90a7a0ec8 upstream
Introduce the 'l1tf=' kernel command line option to allow for boot-time
switching of mitigation that is used on processors affected by L1TF.
The possible values are:
full
Provides all available mitigations for the L1TF vulnerability. Disables
SMT and enables all mitigations in the hypervisors. SMT control via
/sys/devices/system/cpu/smt/control is still possible after boot.
Hypervisors will issue a warning when the first VM is started in
a potentially insecure configuration, i.e. SMT enabled or L1D flush
disabled.
full,force
Same as 'full', but disables SMT control. Implies the 'nosmt=force'
command line option. sysfs control of SMT and the hypervisor flush
control is disabled.
flush
Leaves SMT enabled and enables the conditional hypervisor mitigation.
Hypervisors will issue a warning when the first VM is started in a
potentially insecure configuration, i.e. SMT enabled or L1D flush
disabled.
flush,nosmt
Disables SMT and enables the conditional hypervisor mitigation. SMT
control via /sys/devices/system/cpu/smt/control is still possible
after boot. If SMT is reenabled or flushing disabled at runtime
hypervisors will issue a warning.
flush,nowarn
Same as 'flush', but hypervisors will not warn when
a VM is started in a potentially insecure configuration.
off
Disables hypervisor mitigations and doesn't emit any warnings.
Default is 'flush'.
Let KVM adhere to these semantics, which means:
- 'lt1f=full,force' : Performe L1D flushes. No runtime control
possible.
- 'l1tf=full'
- 'l1tf-flush'
- 'l1tf=flush,nosmt' : Perform L1D flushes and warn on VM start if
SMT has been runtime enabled or L1D flushing
has been run-time enabled
- 'l1tf=flush,nowarn' : Perform L1D flushes and no warnings are emitted.
- 'l1tf=off' : L1D flushes are not performed and no warnings
are emitted.
KVM can always override the L1D flushing behavior using its 'vmentry_l1d_flush'
module parameter except when lt1f=full,force is set.
This makes KVM's private 'nosmt' option redundant, and as it is a bit
non-systematic anyway (this is something to control globally, not on
hypervisor level), remove that option.
Add the missing Documentation entry for the l1tf vulnerability sysfs file
while at it.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Jiri Kosina <jkosina@suse.cz>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lkml.kernel.org/r/20180713142323.202758176@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a399477e52 upstream
Add a mitigation mode parameter "vmentry_l1d_flush" for CVE-2018-3620, aka
L1 terminal fault. The valid arguments are:
- "always" L1D cache flush on every VMENTER.
- "cond" Conditional L1D cache flush, explained below
- "never" Disable the L1D cache flush mitigation
"cond" is trying to avoid L1D cache flushes on VMENTER if the code executed
between VMEXIT and VMENTER is considered safe, i.e. is not bringing any
interesting information into L1D which might exploited.
[ tglx: Split out from a larger patch ]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26acfb666a upstream
If the L1TF CPU bug is present we allow the KVM module to be loaded as the
major of users that use Linux and KVM have trusted guests and do not want a
broken setup.
Cloud vendors are the ones that are uncomfortable with CVE 2018-3620 and as
such they are the ones that should set nosmt to one.
Setting 'nosmt' means that the system administrator also needs to disable
SMT (Hyper-threading) in the BIOS, or via the 'nosmt' command line
parameter, or via the /sys/devices/system/cpu/smt/control. See commit
05736e4ac1 ("cpu/hotplug: Provide knobs to control SMT").
Other mitigations are to use task affinity, cpu sets, interrupt binding,
etc - anything to make sure that _only_ the same guests vCPUs are running
on sibling threads.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 506a66f374 upstream
Dave Hansen reported, that it's outright dangerous to keep SMT siblings
disabled completely so they are stuck in the BIOS and wait for SIPI.
The reason is that Machine Check Exceptions are broadcasted to siblings and
the soft disabled sibling has CR4.MCE = 0. If a MCE is delivered to a
logical core with CR4.MCE = 0, it asserts IERR#, which shuts down or
reboots the machine. The MCE chapter in the SDM contains the following
blurb:
Because the logical processors within a physical package are tightly
coupled with respect to shared hardware resources, both logical
processors are notified of machine check errors that occur within a
given physical processor. If machine-check exceptions are enabled when
a fatal error is reported, all the logical processors within a physical
package are dispatched to the machine-check exception handler. If
machine-check exceptions are disabled, the logical processors enter the
shutdown state and assert the IERR# signal. When enabling machine-check
exceptions, the MCE flag in control register CR4 should be set for each
logical processor.
Reverting the commit which ignores siblings at enumeration time solves only
half of the problem. The core cpuhotplug logic needs to be adjusted as
well.
This thoughtful engineered mechanism also turns the boot process on all
Intel HT enabled systems into a MCE lottery. MCE is enabled on the boot CPU
before the secondary CPUs are brought up. Depending on the number of
physical cores the window in which this situation can happen is smaller or
larger. On a HSW-EX it's about 750ms:
MCE is enabled on the boot CPU:
[ 0.244017] mce: CPU supports 22 MCE banks
The corresponding sibling #72 boots:
[ 1.008005] .... node #0, CPUs: #72
That means if an MCE hits on physical core 0 (logical CPUs 0 and 72)
between these two points the machine is going to shutdown. At least it's a
known safe state.
It's obvious that the early boot can be hit by an MCE as well and then runs
into the same situation because MCEs are not yet enabled on the boot CPU.
But after enabling them on the boot CPU, it does not make any sense to
prevent the kernel from recovering.
Adjust the nosmt kernel parameter documentation as well.
Reverts: 2207def700 ("x86/apic: Ignore secondary threads if nosmt=force")
Reported-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05736e4ac1 upstream
Provide a command line and a sysfs knob to control SMT.
The command line options are:
'nosmt': Enumerate secondary threads, but do not online them
'nosmt=force': Ignore secondary threads completely during enumeration
via MP table and ACPI/MADT.
The sysfs control file has the following states (read/write):
'on': SMT is enabled. Secondary threads can be freely onlined
'off': SMT is disabled. Secondary threads, even if enumerated
cannot be onlined
'forceoff': SMT is permanentely disabled. Writes to the control
file are rejected.
'notsupported': SMT is not supported by the CPU
The command line option 'nosmt' sets the sysfs control to 'off'. This
can be changed to 'on' to reenable SMT during runtime.
The command line option 'nosmt=force' sets the sysfs control to
'forceoff'. This cannot be changed during runtime.
When SMT is 'on' and the control file is changed to 'off' then all online
secondary threads are offlined and attempts to online a secondary thread
later on are rejected.
When SMT is 'off' and the control file is changed to 'on' then secondary
threads can be onlined again. The 'off' -> 'on' transition does not
automatically online the secondary threads.
When the control file is set to 'forceoff', the behaviour is the same as
setting it to 'off', but the operation is irreversible and later writes to
the control file are rejected.
When the control status is 'notsupported' then writes to the control file
are rejected.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 218bbea11a upstream.
Add support for the four-port variant of the Qualcomm QCA833x switch.
The CPU port default link settings can be reconfigured using
a fixed-link sub-node.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7e5d05e18b ]
We need to introduce a new compatible name for the Meson-AXG SoC
in order to support the RMII 100M ethernet PHY, since the PRG_ETH0
register of the dwmac glue layer is changed from previous old SoC.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 03d9fbc397 ]
The Meson8m2 SoC is a variant of Meson8 with some updates from Meson8b
(such as the Gigabit capable DesignWare MAC).
It is mostly pin compatible with Meson8, only 10 (existing) CBUS pins
get an additional function (four of these are Ethernet RXD2, RXD3, TXD2
and TXD3 which are required when the board uses an RGMII PHY).
The AOBUS pins seem to be identical on Meson8 and Meson8m2.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 002fe996f6 ]
When we create an mdev device, we check for duplicates against the
parent device and return -EEXIST if found, but the mdev device
namespace is global since we'll link all devices from the bus. We do
catch this later in sysfs_do_create_link_sd() to return -EEXIST, but
with it comes a kernel warning and stack trace for trying to create
duplicate sysfs links, which makes it an undesirable response.
Therefore we should really be looking for duplicates across all mdev
parent devices, or as implemented here, against our mdev device list.
Using mdev_list to prevent duplicates means that we can remove
mdev_parent.lock, but in order not to serialize mdev device creation
and removal globally, we add mdev_device.active which allows UUIDs to
be reserved such that we can drop the mdev_list_lock before the mdev
device is fully in place.
Two behavioral notes; first, mdev_parent.lock had the side-effect of
serializing mdev create and remove ops per parent device. This was
an implementation detail, not an intentional guarantee provided to
the mdev vendor drivers. Vendor drivers can trivially provide this
serialization internally if necessary. Second, review comments note
the new -EAGAIN behavior when the device, and in particular the remove
attribute, becomes visible in sysfs. If a remove is triggered prior
to completion of mdev_device_create() the user will see a -EAGAIN
error. While the errno is different, receiving an error during this
period is not, the previous implementation returned -ENODEV for the
same condition. Furthermore, the consistency to the user is improved
in the case where mdev_device_remove_ops() returns error. Previously
concurrent calls to mdev_device_remove() could see the device
disappear with -ENODEV and return in the case of error. Now a user
would see -EAGAIN while the device is in this transitory state.
Reviewed-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a43ae4dfe5 upstream.
On a system where the firmware implements ARCH_WORKAROUND_2,
it may be useful to either permanently enable or disable the
workaround for cases where the user decides that they'd rather
not get a trap overhead, and keep the mitigation permanently
on or off instead of switching it on exception entry/exit.
In any case, default to the mitigation being enabled.
Reviewed-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3f9cdee592 upstream.
Removed Kbuild documentation for INSTALL_FW_PATH.
The kbuild symbol INSTALL_FW_PATH was removed from Kbuild tools in
September 2017 (for 4.14) but the symbol was not deleted from
the kbuild documentation, so do that now.
Fixes: 5620a0d1aa ("firmware: delete in-kernel firmware")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: stable@vger.kernel.org # 4.14+
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a95691bc54 ]
This patch adds support for the BCM5389 switch connected through MDIO.
Signed-off-by: Damien Thébault <damien.thebault@vitec.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b6c84ba22f upstream.
Currently we see a kernel-oops reported on Power-9 while attaching a
context to an AFU, with radix-mode and sysfs attr 'prefault_mode' set
to anything other than 'none'. The backtrace of the oops is of this
form:
Unable to handle kernel paging request for data at address 0x00000080
Faulting instruction address: 0xc00800000bcf3b20
cpu 0x1: Vector: 300 (Data Access) at [c00000037f003800]
pc: c00800000bcf3b20: cxl_load_segment+0x178/0x290 [cxl]
lr: c00800000bcf39f0: cxl_load_segment+0x48/0x290 [cxl]
sp: c00000037f003a80
msr: 9000000000009033
dar: 80
dsisr: 40000000
current = 0xc00000037f280000
paca = 0xc0000003ffffe600 softe: 3 irq_happened: 0x01
pid = 3529, comm = afp_no_int
<snip>
cxl_prefault+0xfc/0x248 [cxl]
process_element_entry_psl9+0xd8/0x1a0 [cxl]
cxl_attach_dedicated_process_psl9+0x44/0x130 [cxl]
native_attach_process+0xc0/0x130 [cxl]
afu_ioctl+0x3f4/0x5e0 [cxl]
do_vfs_ioctl+0xdc/0x890
ksys_ioctl+0x68/0xf0
sys_ioctl+0x40/0xa0
system_call+0x58/0x6c
The issue is caused as on Power-8 the AFU attr 'prefault_mode' was
used to improve initial storage fault performance by prefaulting
process segments. However on Power-9 with radix mode we don't have
Storage-Segments that we can prefault. Also prefaulting process Pages
will be too costly and fine-grained.
Hence, since the prefaulting mechanism doesn't makes sense of
radix-mode, this patch updates prefault_mode_store() to not allow any
other value apart from CXL_PREFAULT_NONE when radix mode is enabled.
Fixes: f24be42aab ("cxl: Add psl9 specific code")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 666902e42f upstream.
"%pCr" formats the current rate of a clock, and calls clk_get_rate().
The latter obtains a mutex, hence it must not be called from atomic
context.
Remove support for this rarely-used format, as vsprintf() (and e.g.
printk()) must be callable from any context.
Any remaining out-of-tree users will start seeing the clock's name
printed instead of its rate.
Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Fixes: 900cca2944 ("lib/vsprintf: add %pC{,n,r} format specifiers for clocks")
Link: http://lkml.kernel.org/r/1527845302-12159-5-git-send-email-geert+renesas@glider.be
To: Jia-Ju Bai <baijiaju1990@gmail.com>
To: Jonathan Corbet <corbet@lwn.net>
To: Michael Turquette <mturquette@baylibre.com>
To: Stephen Boyd <sboyd@kernel.org>
To: Zhang Rui <rui.zhang@intel.com>
To: Eduardo Valentin <edubezval@gmail.com>
To: Eric Anholt <eric@anholt.net>
To: Stefan Wahren <stefan.wahren@i2se.com>
To: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-doc@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org # 4.1+
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
