Recent changes (KVM: make processes waiting on vcpu mutex killable)
now requires to check the return value of vcpu_load. This triggered
a warning in s390 specific kvm code. Turns out that we can actually
remove the put/load, since schedule will do the right thing via
the preempt notifiers.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
we only use that to tell copy_thread() done by syscall from that
done by kernel_thread(). However, it's easier to do simply by
checking PF_KTHREAD in thread flags.
Merge sys_clone() guts for 32bit and 64bit, while we are at it...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This named the sleep mode pin configurations as *slpm* rather
than *sleep* to correspond better with the settings from the
datasheet. It also defines an optional sleep mode for the SPI
controller SPI2.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The use of regsets has removed the need for many private ptrace requests,
so remove the corresponding definitions from the user-visible ptrace.h
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
It gets clobbered by the kernel's VISEntryHalf, so we have to save it
in a different register than the set clobbered by that macro.
The instance in glibc is OK and doesn't have this problem.
Signed-off-by: David S. Miller <davem@davemloft.net>
cast5/avx incorrectly XORs new IV over old IV at end of CBC encryption
function when it should store. This causes CBC encryption to give
incorrect output on multi-page encryption requests.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Some Orion5x devices allocate their coherent buffers from atomic
context. Increase size of atomic coherent pool to make sure such the
allocations won't fail during boot.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
We already have a flag word to indicate the existence of MISC_ENABLES,
so use the same flag word to indicate existence of cr4 and EFER, and
always restore them if they exist. That way if something passes a
nonzero value when the value *should* be zero, we will still
initialize it.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Link: http://lkml.kernel.org/r/1348529239-17943-1-git-send-email-hpa@linux.intel.com
%cr4 is supposed to reflect a set of features into which the operating
system is opting in. If the BIOS or bootloader leaks bits here, this
is not desirable. Consider a bootloader passing in %cr4.pae set to a
legacy paging kernel, for example -- it will not have any immediate
effect, but the kernel would crash when turning paging on.
A similar argument applies to %eflags, and since we have to look for
%eflags.id being settable we can use a sequence which clears %eflags
as a side effect.
Note that we already do this for x86-64.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1348529239-17943-1-git-send-email-hpa@linux.intel.com
do_notify_resume() may be called on irq or exception
exit. But at that time the exception has already called
rcu_user_enter() and the irq has already called rcu_irq_exit().
Since it can use RCU read side critical section, we must call
rcu_user_exit() before doing anything there. Then we must call
back rcu_user_enter() after this function because we know we are
going to userspace from there.
This complete support for userspace RCU extended quiescent state
in x86-64.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Alessio Igor Bogani <abogani@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Avi Kivity <avi@redhat.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Max Krasnyansky <maxk@qualcomm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sven-Thorsten Dietrich <thebigcorporation@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This way we can exit the RCU extended quiescent state before
we schedule a new task from irq/exception exit.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Alessio Igor Bogani <abogani@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Avi Kivity <avi@redhat.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Max Krasnyansky <maxk@qualcomm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sven-Thorsten Dietrich <thebigcorporation@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Add necessary hooks to x86 exception for userspace
RCU extended quiescent state support.
This includes traps, page fault, debug exceptions, etc...
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Alessio Igor Bogani <abogani@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Avi Kivity <avi@redhat.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Max Krasnyansky <maxk@qualcomm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sven-Thorsten Dietrich <thebigcorporation@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
There is some unnatural label based layout in this function.
Convert the unnecessary goto to readable conditional blocks.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Add syscall slow path hooks to notify syscall entry
and exit on CPUs that want to support userspace RCU
extended quiescent state.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Alessio Igor Bogani <abogani@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Avi Kivity <avi@redhat.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Max Krasnyansky <maxk@qualcomm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sven-Thorsten Dietrich <thebigcorporation@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Clear the syscalls hook of a task when it's scheduled out so that if
the task migrates, it doesn't run the syscall slow path on a CPU
that might not need it.
Also set the syscalls hook on the next task if needed.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Alessio Igor Bogani <abogani@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Avi Kivity <avi@redhat.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Max Krasnyansky <maxk@qualcomm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sven-Thorsten Dietrich <thebigcorporation@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
We can have either shared kernel or jump label support, but not both.
If a kernel gets IPL'ed from an NSS it's not possible to patch the
text segment, since it's read-only.
Therefore any static branches cannot be updated. So we need to make
sure that shared kernel support is disabled if jump label support
is enabled.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for new BPF_S_ANC_ALU_XOR_X instruction which got added
with ffe06c17 "filter: add XOR operation".
s390 version of 4bfaddf1 "x86 bpf_jit: support BPF_S_ANC_ALU_XOR_X instruction".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Same as 0fa0e2f0 "x86: Move call to print_modules() out of show_regs()".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Same as 0d26d1d8 "x86/mm: Mark free_initrd_mem() as __init".
In addition also add the __init annotation to setup_zero_pages().
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The generic variant has a local_irq_save/restore pair which is quite
expensive. It is sufficient to disable preemption, which is a no-op
with !CONFIG_PREEMPT and then use the regular xchg macro.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Since "Kconfig: split the s390 base menu" CONFIG_KEXEC gets always selected.
Therefore there is no point in keeping CONFIG_KEXEC anywhere.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use designated initializers for the irq class array in irq.c so
it's always guaranteed that the order of elements is equal to
their corresponding parts in irq.h.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Get rid of these:
arch/s390/kernel/smp.c:134:19: warning: ‘status’ may be used uninitialized in this function [-Wuninitialized]
arch/s390/mm/pgtable.c:641:10: warning: ‘table’ may be used uninitialized in this function [-Wuninitialized]
arch/s390/mm/pgtable.c:644:12: warning: ‘page’ may be used uninitialized in this function [-Wuninitialized]
drivers/s390/cio/cio.c:1037:14: warning: ‘schid’ may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move fill_cpu_elf_notes() prototype to header file.
This way we get compile errors if e.g. the number of function
parameters get changed.
Otherwise it's possible to change just the definition and everything
else still compiles fine, but the result is broken code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add appropriate header file:
arch/s390/kernel/process.c:327:15: warning: symbol 'arch_align_stack' was not declared.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
if (MACHINE_HAS_TE) translates to if (0) on !CONFIG_64BIT however the
compiler still warns about invalid shifts within non-reachable code.
So add an explicit ifdef to get rid of this warning:
arch/s390/kernel/ptrace.c: In function ‘update_per_regs’:
arch/s390/kernel/ptrace.c:63:4: warning: left shift count >= width of type [enabled by default]
arch/s390/kernel/ptrace.c:65:4: warning: left shift count >= width of type [enabled by default]
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The early kernel decrompressing code can't call into the kernel
in order to profile branches. Fixes this link error:
arch/s390/boot/compressed/misc.o: In function `decompress_kernel':
misc.c:(.text+0x9a6): undefined reference to `ftrace_likely_update'
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The whole hardware support is only available in zArch mode.
Fixes also this compile warning:
arch/s390/kernel/perf_cpum_cf.c: In function ‘cpumf_pmu_init’:
arch/s390/kernel/perf_cpum_cf.c:670:2: warning: left shift count >= width of type [enabled by default]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use for_each_set_bit() to simplify the code.
spatch with a semantic match is used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change return value of appldata_asm() to -EOPNOTSUPP in case of an
error. The return value was only used internally and not passed to
user space.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Returning -ENOSYS on kexec_load() is a bad idea since user space cannot
tell if the system call is not implmented or if it failed.
Use -EOPNOTSUPP in case somebody tries a kexec_load on a NSS image based
kernel instead.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change -ENOSYS to -EOPNOTSUPP. Return value is used only internally.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change return code handling of the stsi() function:
In case function code 0 was specified the return value is the
current configuration level (already shifted). That way all
the code that actually copied the stsi_0() function can go
away.
Otherwise the return value is 0 (success) or negative to
indicate an error (currently only -EOPNOTSUPP).
Also stsi() is no longer an inline function. The function is
not performance critical, but every caller would generate an
exception table entry for this function.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This is the s390 port of 70627654 "x86, extable: Switch to relative
exception table entries".
Reduces the size of our exception tables by 50% on 64 bit builds.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the spinlock from struct scm_device. drvdata and attributes
are guarded via device_lock.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The cpu polarization member is the only per cpu state that is not part
of the pcpu structure. So add it there and have everything in one place.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The maximum nesting of the cpu topology is evaluated when /proc/sysinfo
is the first time read. This happens without a lock and a concurrent
reader on a different cpu can see and use an invalid intermediate value.
Besides the fact that this race is quite unlikely the worst thing that
could happen is that /proc/sysinfo would contain bogus information about
the machine's cpu topology.
Nevertheless this should be fixed. So move the detection code to the
early machine detection code and since now the value is early available
use it in the topology code as well.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch introduces the __get_user_pages_fast() function on s390,
which will be needed with CONFIG_TRANSPARENT_HUGEPAGE and futex.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a couple of missing fields that were introduced with z196.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current proc implementation of the /proc/sysinfo file writes all
informations contained in all system information blocks to a single
page.
This is done by calling sprintf all the time in the expectation that
everything will fit into a single page. This however is not necessarily
true if the configuration of a machine is very large.
So convert /proc/sysinfo to avoid writing into random memory regions.
For readability reasons a couple of lines are longer than 80 characters.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Any change to sysinfo.h causes a whole kernel recompile since sysinfo.h is
included by topology.h, which again is used nearly everywhere.
So remove that include and add a forward declaration instead.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Shorten the code for addressing mode initialization. Also add missing
__init annotations, since this code is only used during kernel initialization.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Renaming the globally visible variable "user_mode" to "addressing_mode" in
order to fix a name clash was not a good idea. (Commit 37fe1d73 "s390/mm:
rename user_mode variable to addressing_mode")
Looking at the code after a couple of weeks one thinks: addressing mode of
what?
So rename the variable again. This time to s390_user_mode. Which hopefully
makes more sense.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change the default addressing mode so that user space runs in primary space
and the kernel runs in home space.
In addition remove the "switch_amode" kernel parameter so all users who
already specified they want the new default behaviour will stay in the
"switched" mode instead of in the opposite they intended.
If there is a need to switch addressing modes, this can be done with the
"user_mode" kernel parameter: user_mode=home
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When a sigp instruction is issued it may store a status. This status is
currently stored in a per cpu field of the target cpu.
If multiple cpus issue a sigp instruction with the same target cpu
and a status is stored the result is not necessarily as expected.
Currently this is not an issue:
- on cpu hotplug no sigps, except "restart" and "sense" are sent to the
target cpu.
- on external call we don't look at the status if it is stored
- on sense running the condition code "status stored" is sufficient to
tell if a cpu is running or not
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a line for each cpu cache to /proc/cpuinfo.
Since we only have information of private cpu caches in sysfs we
add a line for each cpu cache in /proc/cpuinfo which will also
contain information about shared caches.
For a z196 machine /proc/cpuinfo now looks like:
vendor_id : IBM/S390
bogomips per cpu: 14367.00
features : esan3 zarch stfle msa ldisp eimm dfp etf3eh highgprs
cache0 : level=1 type=Data scope=Private size=64K line_size=256 associativity=4
cache1 : level=1 type=Instruction scope=Private size=128K line_size=256 associativity=8
cache2 : level=2 type=Unified scope=Private size=1536K line_size=256 associativity=12
cache3 : level=3 type=Unified scope=Shared size=24576K line_size=256 associativity=12
cache4 : level=4 type=Unified scope=Shared size=196608K line_size=256 associativity=24
processor 0: version = FF, identification = 000123, machine = 2817
processor 1: version = FF, identification = 100123, machine = 2817
processor 2: version = FF, identification = 200123, machine = 2817
processor 3: version = FF, identification = 200123, machine = 2817
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Allow user-space processes to use transactional execution (TX).
If the TX facility is available user space programs can use
transactions for fine-grained serialization based on the data
objects that are referenced during a transaction. This is
useful for lockless data structures and speculative compiler
optimizations.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Allow user-space threads to use runtime instrumentation (RI). To enable RI
for a thread there is a new s390 specific system call, sys_s390_runtime_instr,
that takes as parameter a realtime signal number. If the RI facility is
available the system call sets up a control block for the calling thread with
the appropriate permissions for the thread to modify the control block.
The user-space thread can then use the store and modify RI instructions to
alter the control block and start/stop the instrumentation via RION/RIOFF.
If the user specified program buffer runs full RI triggers an external
interrupt. The external interrupt is translated to a real-time signal that
is delivered to the thread that enabled RI on that CPU. The number of
the real-time signal is the number specified in the RI system call. So,
user-space can select any available real-time signal number in case the
application itself uses real-time signals for other purposes.
The kernel saves the RI control blocks on task switch only if the running
thread was enabled for RI. Therefore, the performance impact on task switch
should be negligible if RI is not used.
RI is only enabled for user-space mode and is disabled for the supervisor
state.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for EADM interrupt statistics in /proc/interrupts.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This driver allows usage of EADM subchannels. EADM subchannels
act as a communication vehicle for SCM increments.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Detect an scm change notification in store event information.
Update affected scm devices and notify their drivers.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Bus driver to manage Storage Class Memory.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add structures to be used by the eadm subchannel driver.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add the eadm facility bits to the css characteristics and move
them to a new header.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
machine_crash_shutdown() was the only function in crash.c.
So move the function and delete one file.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Unify all our cpu hotplug notifiers to mask out the CPU_TASKS_FROZEN
bit, so we don't have to add all the *_FROZEN variant cases to the
notifiers.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For SMP and !SMP smp_find_processor_id() either takes a u16 or
an unsigned int argument. Fix this so both versions take a u16.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
CONFIG_S390_GUEST determines whether virtio guest drivers are built, and
the virtio console is not enforced as default.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Split the base menu into more descriptive categories like processor,
memory, etc. and move virtualization related entries to the
Virtualization menu.
Also select KEXEC unconditionally.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Expose cpu cache topology via sysfs.
The created sysfs directory structure is compatible to what x86, ia64
and powerpc have.
On s390 we expose only information about cpu caches which are private
to a cpu via sysfs . Caches which are shared between cpus do not have
a sysfs representation.
The reason for that is that the file "shared_cpu_map" is mandatory
and only if running under LPAR it is possible to tell which cpus
share which cache. Second level hypervisors however do not and cannot
expose that information to guests.
In order to have a consistent view we made the choice to always only
expose information about private cpu caches via sysfs.
Example for a z196 cpu (cpu1 in /sys/devices/cpu):
cpu1/cache/index0/size -- 64K
cpu1/cache/index0/type -- Data
cpu1/cache/index0/level -- 1
cpu1/cache/index0/number_of_sets -- 64
cpu1/cache/index0/shared_cpu_map -- 00000000,00000002
cpu1/cache/index0/shared_cpu_list -- 1
cpu1/cache/index0/coherency_line_size -- 256
cpu1/cache/index0/ways_of_associativity -- 4
cpu1/cache/index1/size -- 128K
cpu1/cache/index1/type -- Instruction
cpu1/cache/index1/level -- 1
cpu1/cache/index1/number_of_sets -- 64
cpu1/cache/index1/shared_cpu_map -- 00000000,00000002
cpu1/cache/index1/shared_cpu_list -- 1
cpu1/cache/index1/coherency_line_size -- 256
cpu1/cache/index1/ways_of_associativity -- 8
cpu1/cache/index2/size -- 1536K
cpu1/cache/index2/type -- Unified
cpu1/cache/index2/level -- 2
cpu1/cache/index2/number_of_sets -- 512
cpu1/cache/index2/shared_cpu_map -- 00000000,00000002
cpu1/cache/index2/shared_cpu_list -- 1
cpu1/cache/index2/coherency_line_size -- 256
cpu1/cache/index2/ways_of_associativity -- 12
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
So far, large page support was completely disabled with
CONFIG_DEBUG_PAGEALLOC, although it would be sufficient if only the
large page kernel mapping was disabled. This patch enables large page
support with CONFIG_DEBUG_PAGEALLOC, while it prevents the large kernel
mapping in that case.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Our memcpy and memcmp variants were implemented by calling the corresponding
gcc builtin variants.
However gcc is free to replace a call to __builtin_memcmp with a call to memcmp
which, when called, will result in an endless recursion within memcmp.
So let's provide asm variants and also fix the variants that are used for
uncompressing the kernel image.
In addition remove all other occurences of builtin function calls.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make use of new immediate instructions that came with the
extended immediate and general instruction extension facilities.
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The s390 implementation of the JIT compiler for packet filter speedup.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Create a new config option under the RCU menu that put
CPUs under RCU extended quiescent state (as in dynticks
idle mode) when they run in userspace. This require
some contribution from architectures to hook into kernel
and userspace boundaries.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Alessio Igor Bogani <abogani@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Avi Kivity <avi@redhat.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Gilad Ben Yossef <gilad@benyossef.com>
Cc: Hakan Akkan <hakanakkan@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Max Krasnyansky <maxk@qualcomm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sven-Thorsten Dietrich <thebigcorporation@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Cleanup the label maze in this function. Having a
seperate function to first handle the traps that don't
generate a signal makes it easier to convert into
more readable conditional paths.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1348577479-2564-1-git-send-email-fweisbec@gmail.com
[ Fixed 32-bit build failure. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
GAS in binutils(2.16.91) could not parse parentheses within
macro parameters unless fully parenthesized, and this is a
workaround to make old gas work without generating below errors:
arch/x86/kernel/entry_64.S: Assembler messages:
arch/x86/kernel/entry_64.S:387: Error: too many positional arguments
arch/x86/kernel/entry_64.S:389: Error: too many positional arguments
[...]
Signed-off-by: Tao Guo <glorioustao@gmail.com>
Reluctantly-Acked-by: Jan Beulich <jbeulich@novell.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1348648102-12653-1-git-send-email-glorioustao@gmail.com
[ Jan argues that these old GAS versions are fragile - which is so, but lets give them a chance. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 31d2092eb0 ("x86: move
mp_register_lapic_address to boot.c") renamed mp_register_lapic
to acpi_register_lapic. But mp_register_lapic remains in a
comment. So the patch rename it.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/50625239.3050403@jp.fujitsu.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add device nodes for the four instances of dw_mmc controllers in
EXYNOS5250 and enable instance 0 and 2 for the SMDK5250 board.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add entries if MSHC controllers in AUXDATA table for correct
device name initialization.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add clock instances for bic("bus interface unit clock") and ciu("card
interface unit clock") of the all four MSHC controller instances.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
With SMAP, the [f][x]rstor_checking() functions are no longer usable
for user-space pointers by applying a simple __force cast. Instead,
create new [f][x]rstor_user() functions which do the proper SMAP
magic.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1343171129-2747-3-git-send-email-suresh.b.siddha@intel.com
Pull more networking fixes from David Miller:
1) Eric Dumazet discovered and fixed what turned out to be a family of
bugs. These functions were using pskb_may_pull() which might need
to reallocate the linear SKB data buffer, but the callers were not
expecting this possibility. The callers have cached pointers to the
packet header areas, and would need to reload them if we were to
continue using pskb_may_pull().
So they could end up reading garbage.
It's easier to just change these RAW4/RAW6/MIP6 routines to use
skb_header_pointer() instead of pskb_may_pull(), which won't modify
the linear SKB data area.
2) Dave Jone's syscall spammer caught a case where a non-TCP socket can
call down into the TCP keepalive code. The case basically involves
creating a raw socket with sk_protocol == IPPROTO_TCP, then calling
setsockopt(sock_fd, SO_KEEPALIVE, ...)
Fixed by Eric Dumazet.
3) Bluetooth devices do not get configured properly while being powered
on, resulting in always using legacy pairing instead of SSP. Fix
from Andrzej Kaczmarek.
4) Bluetooth cancels delayed work erroneously, put stricter checks in
place. From Andrei Emeltchenko.
5) Fix deadlock between cfg80211_mutex and reg_regdb_search_mutex in
cfg80211, from Luis R. Rodriguez.
6) Fix interrupt double release in iwlwifi, from Emmanuel Grumbach.
7) Missing module license in bcm87xx driver, from Peter Huewe.
8) Team driver can lose port changed events when adding devices to a
team, fix from Jiri Pirko.
9) Fix endless loop when trying ot unregister PPPOE device in zombie
state, from Xiaodong Xu.
10) batman-adv layer needs to set MAC address of software device
earlier, otherwise we call tt_local_add with it uninitialized.
11) Fix handling of KSZ8021 PHYs, it's matched currently by KS8051 but
that doesn't program the device properly. From Marek Vasut.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
ipv6: mip6: fix mip6_mh_filter()
ipv6: raw: fix icmpv6_filter()
net: guard tcp_set_keepalive() to tcp sockets
phy/micrel: Add missing header to micrel_phy.h
phy/micrel: Rename KS80xx to KSZ80xx
phy/micrel: Implement support for KSZ8021
batman-adv: Fix symmetry check / route flapping in multi interface setups
batman-adv: Fix change mac address of soft iface.
pppoe: drop PPPOX_ZOMBIEs in pppoe_release
team: send port changed when added
ipv4: raw: fix icmp_filter()
net/phy/bcm87xx: Add MODULE_LICENSE("GPL") to GPL driver
iwlwifi: don't double free the interrupt in failure path
cfg80211: fix possible circular lock on reg_regdb_search()
Bluetooth: Fix not removing power_off delayed work
Bluetooth: Fix freeing uninitialized delayed works
Bluetooth: mgmt: Fix enabling LE while powered off
Bluetooth: mgmt: Fix enabling SSP while powered off
There is no known reason for this option to be unavailable on other
archs than x86. They just need to call enable_sched_clock_irqtime()
if they have a sufficiently finegrained clock to make it working.
Move it to the general option and let the user choose between
it and pure tick based or virtual cputime accounting.
Note that virtual cputime accounting already performs a finegrained
irqtime accounting. CONFIG_IRQ_TIME_ACCOUNTING is a kind of middle ground
between tick and virtual based accounting. So CONFIG_IRQ_TIME_ACCOUNTING
and CONFIG_VIRT_CPU_ACCOUNTING are mutually exclusive choices.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Factorize the code that accounts user time into a
single function to avoid code duplication.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Move the code that finds out to which context we account the
cputime into generic layer.
Archs that consider the whole time spent in the idle task as idle
time (ia64, powerpc) can rely on the generic vtime_account()
and implement vtime_account_system() and vtime_account_idle(),
letting the generic code to decide when to call which API.
Archs that have their own meaning of idle time, such as s390
that only considers the time spent in CPU low power mode as idle
time, can just override vtime_account().
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Use a naming based on vtime as a prefix for virtual based
cputime accounting APIs:
- account_system_vtime() -> vtime_account()
- account_switch_vtime() -> vtime_task_switch()
It makes it easier to allow for further declension such
as vtime_account_system(), vtime_account_idle(), ... if we
want to find out the context we account to from generic code.
This also make it better to know on which subsystem these APIs
refer to.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
spi-pl022 got a further update to its devicetree support, completing properties
such that no platform data is necessary anymore. This patch adjusts phy3250.c
accordingly: The supplied platform data is deleted. However, OF_DEV_AUXDATA()
are still necessary due to device naming ("dev:ssp0").
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This patch adjusts the PHY3250 board file to the actual LED configuration
(active high, default-state and trigger configuration).
Signed-off-by: Roland Stigge <stigge@antcom.de>
bigrt.2012.09.23a contains additional commits to reduce scheduling latency
from RCU on huge systems (many hundrends or thousands of CPUs).
doctorture.2012.09.23a contains documentation changes and rcutorture fixes.
fixes.2012.09.23a contains miscellaneous fixes.
hotplug.2012.09.23a contains CPU-hotplug-related changes.
idle.2012.09.23a fixes architectures for which RCU no longer considered
the idle loop to be a quiescent state due to earlier
adaptive-dynticks changes. Affected architectures are alpha,
cris, frv, h8300, m32r, m68k, mn10300, parisc, score, xtensa,
and ia64.
Pull tile gxio ABI fix from Chris Metcalf:
"This fixes a last-minute change in the Tilera hypervisor ABI for TRIO
(PCI root complex) support. We've locked in this ABI going forward
and will make sure no further ABI changes like this occur."
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: gxio iorpc numbering change for TRIO interface
and it can cause bootup crashes on certain AMD machines.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQYGDkAAoJEFjIrFwIi8fJrR0H/2iRt3nH3KeG6S2l2UaSvJuH
BqtUSFFtMxKwAc9WC8gx9lc6y9HFig1SThzWuWJulNpF50QnBp38+OuMzEespoUN
JLJtIp/jlYFZL5w2K7soXq7e0elbWTainPWvz5qJE7RifcnclAOGGrf/0LEVf/FQ
xCjn9MLDq5WzbkwuA7TPMDb9RSD3ZJThMShj82kziwpTaniJCpl4YY0lVYUfknXo
t2NTV6Ze6mkzU5QvxSA2ZJt89vsFXQNpsvUK0WzZfLmzugXqnqQHstaVti64ovZc
e64PW61PIRhaZMCDuieclMXWbXFjkp4AsEQJLv3K/kojG20xJ/X08nmolnl64vw=
=t4AN
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.6-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull a Xen fix from Konrad Rzeszutek Wilk:
"It is a bug-fix when we run the initial PV guest on a AMD K8 machine
and have CONFIG_AMD_NUMA enabled and detect the NUMA topology from the
Northbridge.
We end up in the situation where the initial domain gets too much
information and gets confused and crashes - the fix is to restrict the
domain to get the information - and we do it by just disabling NUMA on
the PV guest (the hypervisor is still able to do its proper NUMA
allocations of guests).
It is OK to disable the PV guest from accessing NUMA data as right now
we do not inject any NUMA node information to the PV guests. When we
do get to that point, then this patch will have to be reverted."
* Disable PV NUMA support as we do not do anything with it (yet) and it
can cause bootup crashes on certain AMD machines.
* tag 'stable/for-linus-3.6-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/boot: Disable NUMA for PV guests.
This patch is a follow-up for patch "filter: add XOR instruction for use
with X/K" that implements BPF x86 JIT parts for the BPF XOR operation.
Signed-off-by: Daniel Borkmann <daniel.borkmann@tik.ee.ethz.ch>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no such part as KS8001, KS8041 or KS8051. There are only
KSZ8001, KSZ8041 and KSZ8051. Rename these parts as such to match
the Micrel naming.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David J. Choi <david.choi@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Linux ARM kernel <linux-arm-kernel@lists.infradead.org>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
An ABI numbering change was made in the hypervisor for Tilera's 4.1
MDE release (just shipped). It's incompatible with the previous 4.0
release ABI numbering, so we track the new numbering going forward.
We plan to avoid modifying ABI numbering for these interfaces again.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
. Convert the trace builtins to use the growing evsel/evlist
tracepoint infrastructure, removing several open coded constructs
like switch like series of strcmp to dispatch events, etc.
Basically what had already been showcased in 'perf sched'.
. Add evsel constructor for tracepoints, that uses libtraceevent
just to parse the /format events file, use it in a new 'perf test'
to make sure the libtraceevent format parsing regressions can
be more readily caught.
. Some strange errors were happening in some builds, but not on the
next, reported by several people, problem was some parser related
files, generated during the build, didn't had proper make deps,
fix from Eric Sandeen.
. Fix some compiling errors on 32-bit, from Feng Tang.
. Don't use sscanf extension %as, not available on bionic, reimplementation
by Irina Tirdea.
. Fix bfd.h/libbfd detection with recent binutils, from Markus Trippelsdorf.
. Introduce struct and cache information about the environment where a
perf.data file was captured, from Namhyung Kim.
. Fix several error paths in libtraceevent, from Namhyung Kim.
Print event causing perf_event_open() to fail in 'perf record',
from Stephane Eranian.
. New 'kvm' analysis tool, from Xiao Guangrong.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=FgCY
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
* Convert the trace builtins to use the growing evsel/evlist
tracepoint infrastructure, removing several open coded constructs
like switch like series of strcmp to dispatch events, etc.
Basically what had already been showcased in 'perf sched'.
* Add evsel constructor for tracepoints, that uses libtraceevent
just to parse the /format events file, use it in a new 'perf test'
to make sure the libtraceevent format parsing regressions can
be more readily caught.
* Some strange errors were happening in some builds, but not on the
next, reported by several people, problem was some parser related
files, generated during the build, didn't had proper make deps,
fix from Eric Sandeen.
* Fix some compiling errors on 32-bit, from Feng Tang.
* Don't use sscanf extension %as, not available on bionic, reimplementation
by Irina Tirdea.
* Fix bfd.h/libbfd detection with recent binutils, from Markus Trippelsdorf.
* Introduce struct and cache information about the environment where a
perf.data file was captured, from Namhyung Kim.
* Fix several error paths in libtraceevent, from Namhyung Kim.
Print event causing perf_event_open() to fail in 'perf record',
from Stephane Eranian.
* New 'kvm' analysis tool, from Xiao Guangrong.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
A recent patch in the linux-next tree caused a build failure on
C6X because C6X didn't define a read_barrier_depends() macro. C6X
does not support SMP and the architecture doesn't provide any
special memory ordering instructions, so it makes sense to just
use the generic barrier.h rather than patching the existing c6x
specific header.
Signed-off-by: Mark Salter <msalter@redhat.com>
Extends the maximum number of UART ports to 6 from 4 because AM335X
device have six UART ports.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP4 the i2c1 bus is dedicated for the PMIC and audio related devices.
Manufacturers can opt to use different codec than twl6040 and also can add
audio related IC to the bus (external amplifier for example on SDP4430).
Make it possible to add different set of additional devices to i2c1 bus on
OMAP4 boards.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated for removal of irqs.h]
Signed-off-by: Tony Lindgren <tony@atomide.com>
If such bit exists on a given CPU, it must be set by the firmware or
boot-loader prior to starting the kernel (see
Documentation/arm64/booting.txt).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In order to add xen EFI frambebuffer video support, it is required to add
xen-efi's new video type (XEN_VGATYPE_EFI_LFB) case and handle it in the
function xen_init_vga and set the video type to VIDEO_TYPE_EFI to enable
efi video mode.
The original patch from which this was broken out from:
http://marc.info/?i=4E099AA6020000780004A4C6@nat28.tlf.novell.com
Signed-off-by: Jan Beulich <JBeulich@novell.com>
Signed-off-by: Tang Liang <liang.tang@oracle.com>
[v2: The original author is Jan Beulich and Liang Tang ported it to upstream]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The xen c/s 25873 allows the hypervisor to retrieve the NUMLOCK flag.
With this patch, the Linux kernel can get the state according to the
data in the BIOS.
Acked-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The hypervisor is in charge of allocating the proper "NUMA" memory
and dealing with the CPU scheduler to keep them bound to the proper
NUMA node. The PV guests (and PVHVM) have no inkling of where they
run and do not need to know that right now. In the future we will
need to inject NUMA configuration data (if a guest spans two or more
NUMA nodes) so that the kernel can make the right choices. But those
patches are not yet present.
In the meantime, disable the NUMA capability in the PV guest, which
also fixes a bootup issue. Andre says:
"we see Dom0 crashes due to the kernel detecting the NUMA topology not
by ACPI, but directly from the northbridge (CONFIG_AMD_NUMA).
This will detect the actual NUMA config of the physical machine, but
will crash about the mismatch with Dom0's virtual memory. Variation of
the theme: Dom0 sees what it's not supposed to see.
This happens with the said config option enabled and on a machine where
this scanning is still enabled (K8 and Fam10h, not Bulldozer class)
We have this dump then:
NUMA: Warning: node ids are out of bound, from=-1 to=-1 distance=10
Scanning NUMA topology in Northbridge 24
Number of physical nodes 4
Node 0 MemBase 0000000000000000 Limit 0000000040000000
Node 1 MemBase 0000000040000000 Limit 0000000138000000
Node 2 MemBase 0000000138000000 Limit 00000001f8000000
Node 3 MemBase 00000001f8000000 Limit 0000000238000000
Initmem setup node 0 0000000000000000-0000000040000000
NODE_DATA [000000003ffd9000 - 000000003fffffff]
Initmem setup node 1 0000000040000000-0000000138000000
NODE_DATA [0000000137fd9000 - 0000000137ffffff]
Initmem setup node 2 0000000138000000-00000001f8000000
NODE_DATA [00000001f095e000 - 00000001f0984fff]
Initmem setup node 3 00000001f8000000-0000000238000000
Cannot find 159744 bytes in node 3
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff81d220e6>] __alloc_bootmem_node+0x43/0x96
Pid: 0, comm: swapper Not tainted 3.3.6 #1 AMD Dinar/Dinar
RIP: e030:[<ffffffff81d220e6>] [<ffffffff81d220e6>] __alloc_bootmem_node+0x43/0x96
.. snip..
[<ffffffff81d23024>] sparse_early_usemaps_alloc_node+0x64/0x178
[<ffffffff81d23348>] sparse_init+0xe4/0x25a
[<ffffffff81d16840>] paging_init+0x13/0x22
[<ffffffff81d07fbb>] setup_arch+0x9c6/0xa9b
[<ffffffff81683954>] ? printk+0x3c/0x3e
[<ffffffff81d01a38>] start_kernel+0xe5/0x468
[<ffffffff81d012cf>] x86_64_start_reservations+0xba/0xc1
[<ffffffff81007153>] ? xen_setup_runstate_info+0x2c/0x36
[<ffffffff81d050ee>] xen_start_kernel+0x565/0x56c
"
so we just disable NUMA scanning by setting numa_off=1.
CC: stable@vger.kernel.org
Reported-and-Tested-by: Andre Przywara <andre.przywara@amd.com>
Acked-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
When either of __alloc_from_contiguous or __alloc_remap_buffer fails
to provide a valid pointer, allocated memory is freed up and an error
is returned. 'pages' was however not freed before returning error.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
remove existing non-dt code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQXBatAAoJEAKiPfwuf9N/VZoIAI7PKNwakjM/KDiVzytwqZ+U
h9kkjYW4ra8MH+jpjFQqvSyIJ3U+t016xqW3ZbqRuZBDgH0I7Gax7QoAZ/ljPlpG
RAKl2l9WVPiBSwCESTpvR5lafBLklk6fL0Z267qIxDGld6YBiWHvTKIh1zDmeCWW
hgDeWtcb1M61VlPrj9nPnCze66h2dUk+QSxaCodv7co5kzb0Q4S7U64BCs0hGe01
kkdoUwnBjdeK0cUhDAJAP1vRyk04N16+H7yp4npmKhv/blKVc3MIRjg1iBV78ncd
Kke/G1B9TJRpNTXdySYnsDQpaCWNSAryKXKkdxP0gh6MW8CMKYc1mdKYcEP3Tk8=
=xG1+
-----END PGP SIGNATURE-----
Merge tag 'vt8500-for-next' of git://git.code.sf.net/p/linuxwmt/code into next/dt
From Tony Prisk:
Update arch-vt8500 and drivers to device tree and
remove existing non-dt code.
* tag 'vt8500-for-next' of git://git.code.sf.net/p/linuxwmt/code:
arm: vt8500: Update arch-vt8500 to devicetree support.
arm: vt8500: gpio: Devicetree support for arch-vt8500
arm: vt8500: doc: Add device tree bindings for arch-vt8500 devices
arm: vt8500: clk: Add Common Clock Framework support
video: vt8500: Add devicetree support for vt8500-fb and wm8505-fb
serial: vt8500: Add devicetree support for vt8500-serial
rtc: vt8500: Add devicetree support for vt8500-rtc
arm: vt8500: Add device tree files for VIA/Wondermedia SoC's
Resolved add/change conflict in drivers/clk/Makefile.
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch moves the sht15.h header from include/linux to
include/linux/platform_data, and update existing support (stargate2
platform) accordingly.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull kbuild fixes from Michal Marek:
"There are two more kbuild fixes for 3.6.
One fixes a race between x86's archscripts target and the rule
(re)building scripts/basic/fixdep. The second is a fix for the
previous attempt at fixing make firmware_install with make 3.82.
This new solution should work with any version of GNU make"
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
x86/kbuild: archscripts depends on scripts_basic
firmware: fix directory creation rule matching with make 3.80
Traditionally, the entire idle task served as an RCU quiescent state.
But when RCU read side critical sections started appearing within the
idle loop, this traditional strategy became untenable. The fix was to
create new RCU APIs named rcu_idle_enter() and rcu_idle_exit(), which
must be called by each architecture's idle loop so that RCU can tell
when it is safe to ignore a given idle CPU.
Unfortunately, this fix was never applied to ia64, a shortcoming remedied
by this commit.
Reported by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Cc: <stable@vger.kernel.org> # 3.3+
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
In the old times, the whole idle task was considered
as an RCU quiescent state. But as RCU became more and
more successful overtime, some RCU read side critical
section have been added even in the code of some
architectures idle tasks, for tracing for example.
So nowadays, rcu_idle_enter() and rcu_idle_exit() must
be called by the architecture to tell RCU about the part
in the idle loop that doesn't make use of rcu read side
critical sections, typically the part that puts the CPU
in low power mode.
This is necessary for RCU to find the quiescent states in
idle in order to complete grace periods.
Add this missing pair of calls in the xtensa's idle loop.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: <stable@vger.kernel.org> # 3.3+
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
In the old times, the whole idle task was considered
as an RCU quiescent state. But as RCU became more and
more successful overtime, some RCU read side critical
section have been added even in the code of some
architectures idle tasks, for tracing for example.
So nowadays, rcu_idle_enter() and rcu_idle_exit() must
be called by the architecture to tell RCU about the part
in the idle loop that doesn't make use of rcu read side
critical sections, typically the part that puts the CPU
in low power mode.
This is necessary for RCU to find the quiescent states in
idle in order to complete grace periods.
Add this missing pair of calls in scores's idle loop.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: <stable@vger.kernel.org> # 3.3+
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
In the old times, the whole idle task was considered
as an RCU quiescent state. But as RCU became more and
more successful overtime, some RCU read side critical
section have been added even in the code of some
architectures idle tasks, for tracing for example.
So nowadays, rcu_idle_enter() and rcu_idle_exit() must
be called by the architecture to tell RCU about the part
in the idle loop that doesn't make use of rcu read side
critical sections, typically the part that puts the CPU
in low power mode.
This is necessary for RCU to find the quiescent states in
idle in order to complete grace periods.
Add this missing pair of calls in the parisc's idle loop.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Parisc <linux-parisc@vger.kernel.org>
Cc: <stable@vger.kernel.org> # 3.3+
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
In the old times, the whole idle task was considered
as an RCU quiescent state. But as RCU became more and
more successful overtime, some RCU read side critical
section have been added even in the code of some
architectures idle tasks, for tracing for example.
So nowadays, rcu_idle_enter() and rcu_idle_exit() must
be called by the architecture to tell RCU about the part
in the idle loop that doesn't make use of rcu read side
critical sections, typically the part that puts the CPU
in low power mode.
This is necessary for RCU to find the quiescent states in
idle in order to complete grace periods.
Add this missing pair of calls in the mn10300's idle loop.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: <stable@vger.kernel.org> # 3.3+
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: David Howells <dhowells@redhat.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
In the old times, the whole idle task was considered
as an RCU quiescent state. But as RCU became more and
more successful overtime, some RCU read side critical
section have been added even in the code of some
architectures idle tasks, for tracing for example.
So nowadays, rcu_idle_enter() and rcu_idle_exit() must
be called by the architecture to tell RCU about the part
in the idle loop that doesn't make use of rcu read side
critical sections, typically the part that puts the CPU
in low power mode.
This is necessary for RCU to find the quiescent states in
idle in order to complete grace periods.
Add this missing pair of calls in the m68k's idle loop.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: m68k <linux-m68k@lists.linux-m68k.org>
Cc: <stable@vger.kernel.org> # 3.3+
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
In the old times, the whole idle task was considered
as an RCU quiescent state. But as RCU became more and
more successful overtime, some RCU read side critical
section have been added even in the code of some
architectures idle tasks, for tracing for example.
So nowadays, rcu_idle_enter() and rcu_idle_exit() must
be called by the architecture to tell RCU about the part
in the idle loop that doesn't make use of rcu read side
critical sections, typically the part that puts the CPU
in low power mode.
This is necessary for RCU to find the quiescent states in
idle in order to complete grace periods.
Add this missing pair of calls in the m32r's idle loop.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: <stable@vger.kernel.org> # 3.3+
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
In the old times, the whole idle task was considered
as an RCU quiescent state. But as RCU became more and
more successful overtime, some RCU read side critical
section have been added even in the code of some
architectures idle tasks, for tracing for example.
So nowadays, rcu_idle_enter() and rcu_idle_exit() must
be called by the architecture to tell RCU about the part
in the idle loop that doesn't make use of rcu read side
critical sections, typically the part that puts the CPU
in low power mode.
This is necessary for RCU to find the quiescent states in
idle in order to complete grace periods.
Add this missing pair of calls in the h8300's idle loop.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: <stable@vger.kernel.org> # 3.3+
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
In the old times, the whole idle task was considered
as an RCU quiescent state. But as RCU became more and
more successful overtime, some RCU read side critical
section have been added even in the code of some
architectures idle tasks, for tracing for example.
So nowadays, rcu_idle_enter() and rcu_idle_exit() must
be called by the architecture to tell RCU about the part
in the idle loop that doesn't make use of rcu read side
critical sections, typically the part that puts the CPU
in low power mode.
This is necessary for RCU to find the quiescent states in
idle in order to complete grace periods.
Add this missing pair of calls in the Frv's idle loop.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: <stable@vger.kernel.org> # 3.3+
Acked-by: David Howells <dhowells@redhat.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
In the old times, the whole idle task was considered
as an RCU quiescent state. But as RCU became more and
more successful overtime, some RCU read side critical
section have been added even in the code of some
architectures idle tasks, for tracing for example.
So nowadays, rcu_idle_enter() and rcu_idle_exit() must
be called by the architecture to tell RCU about the part
in the idle loop that doesn't make use of rcu read side
critical sections, typically the part that puts the CPU
in low power mode.
This is necessary for RCU to find the quiescent states in
idle in order to complete grace periods.
Add this missing pair of calls in the Cris's idle loop.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Cris <linux-cris-kernel@axis.com>
Cc: <stable@vger.kernel.org> # 3.3+
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
In the old times, the whole idle task was considered
as an RCU quiescent state. But as RCU became more and
more successful overtime, some RCU read side critical
section have been added even in the code of some
architectures idle tasks, for tracing for example.
So nowadays, rcu_idle_enter() and rcu_idle_exit() must
be called by the architecture to tell RCU about the part
in the idle loop that doesn't make use of rcu read side
critical sections, typically the part that puts the CPU
in low power mode.
This is necessary for RCU to find the quiescent states in
idle in order to complete grace periods.
Add this missing pair of calls in the Alpha's idle loop.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Tested-by: Michael Cree <mcree@orcon.net.nz>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: alpha <linux-alpha@vger.kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org> # 3.3+
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
cpu_idle() is called on the boot CPU by the init code with
preemption disabled. But the cpu_idle() function in alpha
doesn't handle this when it calls schedule() directly.
Fix it by converting it into schedule_preempt_disabled().
Also disable preemption before calling cpu_idle() from
secondary CPU entry code to stay consistent with this
state.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Tested-by: Michael Cree <mcree@orcon.net.nz>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: alpha <linux-alpha@vger.kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
If arch/x86/kernel/cpuid.c is a module, a CPU might offline or online
between the for_each_online_cpu() loop and the call to
register_hotcpu_notifier in cpuid_init or the call to
unregister_hotcpu_notifier in cpuid_exit. The potential races can
lead to leaks/duplicates, attempts to destroy non-existant devices, or
random pointer dereferences.
For example, in cpuid_exit if:
for_each_online_cpu(cpu)
cpuid_device_destroy(cpu);
class_destroy(cpuid_class);
__unregister_chrdev(CPUID_MAJOR, 0, NR_CPUS, "cpu/cpuid");
<----- CPU onlines
unregister_hotcpu_notifier(&cpuid_class_cpu_notifier);
the hotcpu notifier will attempt to create a device for the
cpuid_class, which the module already destroyed.
This fix surrounds for_each_online_cpu and register_hotcpu_notifier or
unregister_hotcpu_notifier with get_online_cpus+put_online_cpus.
Tested on a VM.
Signed-off-by: Silas Boyd-Wickizer <sbw@mit.edu>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
If arch/x86/kernel/msr.c is a module, a CPU might offline or online
between the for_each_online_cpu(i) loop and the call to
register_hotcpu_notifier in msr_init or the call to
unregister_hotcpu_notifier in msr_exit. The potential races can lead
to leaks/duplicates, attempts to destroy non-existant devices, or
random pointer dereferences.
For example, in msr_init if:
for_each_online_cpu(i) {
err = msr_device_create(i);
if (err != 0)
goto out_class;
}
<----- CPU offlines
register_hotcpu_notifier(&msr_class_cpu_notifier);
and the CPU never onlines before msr_exit, then the module will never
call msr_device_destroy for the associated CPU.
This fix surrounds for_each_online_cpu and register_hotcpu_notifier or
unregister_hotcpu_notifier with get_online_cpus+put_online_cpus.
Tested on a VM.
Signed-off-by: Silas Boyd-Wickizer <sbw@mit.edu>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
If we reset a vcpu on INIT, we so far overwrote dr7 as provided by
KVM_SET_GUEST_DEBUG, and we also cleared switch_db_regs unconditionally.
Fix this by saving the dr7 used for guest debugging and calculating the
effective register value as well as switch_db_regs on any potential
change. This will change to focus of the set_guest_debug vendor op to
update_dp_bp_intercept.
Found while trying to stop on start_secondary.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
To emulate level triggered interrupts, add a resample option to
KVM_IRQFD. When specified, a new resamplefd is provided that notifies
the user when the irqchip has been resampled by the VM. This may, for
instance, indicate an EOI. Also in this mode, posting of an interrupt
through an irqfd only asserts the interrupt. On resampling, the
interrupt is automatically de-asserted prior to user notification.
This enables level triggered interrupts to be posted and re-enabled
from vfio with no userspace intervention.
All resampling irqfds can make use of a single irq source ID, so we
reserve a new one for this interface.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
* 'for-arm-soc-next' of git://git.linaro.org/people/ljones/linux-3.0-ux500:
ARM: ux500: Fix SSP register address format
ARM: ux500: Apply tc3589x's GPIO/IRQ properties to HREF's DT
ARM: ux500: Remove redundant #gpio-cell properties from Snowball DT
ARM: ux500: Add all encompassing sound node to the HREF Device Tree
ARM: ux500: Add nodes for the MSP into the HREF Device Tree
ARM: ux500: Add all known I2C sub-device nodes to the HREF DT
ARM: ux500: Stop registering I2C sub-devices for HREF when DT is enabled
ARM: ux500: Stop registering Audio devices for HREF when DT is enabled
ARM: ux500: Add all encompassing sound node to the Snowball Device Tree
ARM: ux500: Add nodes for the MSP into Device Tree
ARM: ux500: Rename MSP board file to something more meaningful
ARM: ux500: Remove platform registration of MSP devices
ARM: ux500: Stop registering the MOP500 Audio driver from platform code
ARM: ux500: Pass MSP DMA platform data though AUXDATA
ARM: ux500: Fork MSP platform registration for step-by-step DT enablement
ARM: ux500: Add AB8500 CODEC node to DB8500 Device Tree
ARM: ux500: Clean-up MSP platform code
ARM: ux500: Pass SDI DMA information though AUX_DATA to MMCI
ARM: ux500: Add UART support to the HREF Device Tree
ARM: ux500: Add skeleton Device Tree for the HREF reference board
...
+ sync to v3.6-rc6
* stable/late-swiotlb.v3.3:
xen/swiotlb: Fix compile warnings when using plain integer instead of NULL pointer.
xen/swiotlb: Remove functions not needed anymore.
xen/pcifront: Use Xen-SWIOTLB when initting if required.
xen/swiotlb: For early initialization, return zero on success.
xen/swiotlb: Use the swiotlb_late_init_with_tbl to init Xen-SWIOTLB late when PV PCI is used.
xen/swiotlb: Move the error strings to its own function.
xen/swiotlb: Move the nr_tbl determination in its own function.
swiotlb: add the late swiotlb initialization function with iotlb memory
xen/swiotlb: With more than 4GB on 64-bit, disable the native SWIOTLB.
xen/swiotlb: Simplify the logic.
Conflicts:
arch/x86/xen/pci-swiotlb-xen.c
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Pull MIPS fixes from Ralf Baechle:
"Random fixes across arch/mips, essentially.
One fix for an issue in get_user_pages_fast() which previously was
discovered on x86, a miscalculation in the support for the MIPS MT
hardware multithreading support, the RTC support for the Malta and a
fix for a spurious interrupt issue that seems to bite only very
special Malta configurations."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Malta: Don't crash on spurious interrupt.
MIPS: Malta: Remove RTC Data Mode bootstrap breakage
MIPS: mm: Add compound tail page _mapcount when mapped
MIPS: CMP/SMTC: Fix tc_id calculation
Pull ARM and clkdev fixes from Russell King:
"Two patches for clkdev which resolve the long standing issue that the
devm_* versions were dependent on clkdev, which they shouldn't have
been. Instead, they're dependent on HAVE_CLK instead, which implies
that you're providing clk_get() and clk_put().
A small fix to the ARM decompressor to ensure that the page tables are
properly interpreted by the CPU, and reserve syscall 378 for kcmp (the
checksyscalls.sh script is unfortunately currently broken so arch
maintainers aren't getting notified of new syscalls...)
Lastly, a larger fix for an issue between the common clk subsystem and
smp_twd which causes warnings to be spat out."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: reserve syscall 378 for kcmp
ARM: 7535/1: Reprogram smp_twd based on new common clk framework notifiers
ARM: 7537/1: clk: Fix release in devm_clk_put()
ARM: 7532/1: decompressor: reset SCTLR.TRE for VMSA ARMv7 cores
ARM: 7534/1: clk: Make the managed clk functions generically available
__iomem annotation cleanup branch from Arnd.
* cleanup/__iomem: (21 commits)
net: seeq: use __iomem pointers for MMIO
video: da8xx-fb: use __iomem pointers for MMIO
scsi: eesox: use __iomem pointers for MMIO
serial: ks8695: use __iomem pointers for MMIO
input: rpcmouse: use __iomem pointers for MMIO
ARM: samsung: use __iomem pointers for MMIO
ARM: spear13xx: use __iomem pointers for MMIO
ARM: sa1100: use __iomem pointers for MMIO
ARM: prima2: use __iomem pointers for MMIO
ARM: nomadik: use __iomem pointers for MMIO
ARM: msm: use __iomem pointers for MMIO
ARM: lpc32xx: use __iomem pointers for MMIO
ARM: ks8695: use __iomem pointers for MMIO
ARM: ixp4xx: use __iomem pointers for MMIO
ARM: iop32x: use __iomem pointers for MMIO
ARM: iop13xx: use __iomem pointers for MMIO
ARM: integrator: use __iomem pointers for MMIO
ARM: imx: use __iomem pointers for MMIO
ARM: ebsa110: use __iomem pointers for MMIO
ARM: at91: use __iomem pointers for MMIO
...
Signed-off-by: Olof Johansson <olof@lixom.net>
No real need to have a separate core.h from the common.h file. Fold
these two prototypes into the common header file.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Misc SoC-related fixes/cleanups for Samsung platforms
* 'next/devel-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: Add check for NULL in clock interface
ARM: EXYNOS: Put PCM, Slimbus, Spdif clocks to off state
ARM: EXYNOS: Add bus clock for FIMD
ARM: SAMSUNG: Fix HDMI related warnings
ARM: S3C24XX: Add .get_rate callback for "camif-upll" clock
ARM: EXYNOS: Fix incorrect help text
ARM: EXYNOS: Turn off clocks for NAND, OneNAND and TSI controllers
+ sync to 3.6-rc6
Reason for merge:
x86/fpu changed the structure of some of the code that x86/smap
changes; mostly fpu-internal.h but also minor changes to the
signal code.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Resolved Conflicts:
arch/x86/ia32/ia32_signal.c
arch/x86/include/asm/fpu-internal.h
arch/x86/kernel/signal.c
Preemption is disabled between kernel_fpu_begin/end() and as such
it is not a good idea to use these routines in kvm_load/put_guest_fpu()
which can be very far apart.
kvm_load/put_guest_fpu() routines are already called with
preemption disabled and KVM already uses the preempt notifier to save
the guest fpu state using kvm_put_guest_fpu().
So introduce __kernel_fpu_begin/end() routines which don't touch
preemption and use them instead of kernel_fpu_begin/end()
for KVM's use model of saving/restoring guest FPU state.
Also with this change (and with eagerFPU model), fix the host cr0.TS vm-exit
state in the case of VMX. For eagerFPU case, host cr0.TS is always clear.
So no need to worry about it. For the traditional lazyFPU restore case,
change the cr0.TS bit for the host state during vm-exit to be always clear
and cr0.TS bit is set in the __vmx_load_host_state() when the FPU
(guest FPU or the host task's FPU) state is not active. This ensures
that the host/guest FPU state is properly saved, restored
during context-switch and with interrupts (using irq_fpu_usable()) not
stomping on the active FPU state.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1348164109.26695.338.camel@sbsiddha-desk.sc.intel.com
Cc: Avi Kivity <avi@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Pull sparc updates from David Miller:
1) Debugging builds on 32-bit sparc need to handle the R_SPARC_DISP32
relocation, not just 64-bit sparc. From Andreas Larsson.
2) Wei Yongjun noticed that module_alloc() on sparc can return an
error pointer, but that's not allowed. module_alloc() should
return only a valid pointer, or NULL.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: fix the return value of module_alloc()
sparc32: Enable the relocation target R_SPARC_DISP32 for sparc32
Pull x86 fixes from Ingo Molnar:
"Small fixlets"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/init.c: Fix devmem_is_allowed() off by one
x86/kconfig: Remove outdated reference to Intel CPUs in CONFIG_SWIOTLB
The changes to entry_32.S got missed in checkin:
63bcff2a x86, smap: Add STAC and CLAC instructions to control user space access
The resulting kernel was largely functional but SMAP protection could
have been bypassed.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1348256595-29119-9-git-send-email-hpa@linux.intel.com
Use kzalloc() so the struct resource doesn't contain garbage in
fields we don't initialize.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: linux-ia64@vger.kernel.org
Use kzalloc() so the struct resource doesn't contain garbage in
fields we don't initialize.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: x86@kernel.org
Signal handling contains a bunch of accesses to individual user space
items, which causes an excessive number of STAC and CLAC
instructions. Instead, let get/put_user_try ... get/put_user_catch()
contain the STAC and CLAC instructions.
This means that get/put_user_try no longer nests, and furthermore that
it is no longer legal to use user space access functions other than
__get/put_user_ex() inside those blocks. However, these macros are
x86-specific anyway and are only used in the signal-handling paths; a
simple reordering of moving the larger subroutine calls out of the
try...catch blocks resolves that problem.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1348256595-29119-12-git-send-email-hpa@linux.intel.com
When Supervisor Mode Access Prevention (SMAP) is enabled, access to
userspace from the kernel is controlled by the AC flag. To make the
performance of manipulating that flag acceptable, there are two new
instructions, STAC and CLAC, to set and clear it.
This patch adds those instructions, via alternative(), when the SMAP
feature is enabled. It also adds X86_EFLAGS_AC unconditionally to the
SYSCALL entry mask; there is simply no reason to make that one
conditional.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1348256595-29119-9-git-send-email-hpa@linux.intel.com
The STAC/CLAC instructions are only available with SMAP, but on the
other hand they aren't needed if SMAP is not available, or before we
start to run userspace, so construct them as alternatives which start
out as noops and are enabled by the alternatives mechanism.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1348256595-29119-7-git-send-email-hpa@linux.intel.com
A couple of samsung clock locking fixes, at91 device tree gpio
configuration fix and a couple more for shmobile and i.MX.
All small targeted fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=nNwT
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc bug fixes from Olof Johansson:
"A couple of samsung clock locking fixes, at91 device tree gpio
configuration fix and a couple more for shmobile and i.MX.
All small targeted fixes."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM i.MX25: Make timer irq work again
ARM: imx: armadillo5x0: Fix illegal register access
ARM: shmobile: kzm9g: bugfix: correct mmcif interrupt settings
ARM: SAMSUNG: Use spin_lock_{irqsave,irqrestore} in clk_set_rate
ARM: at91: fix missing #interrupt-cells on gpio-controller
ARM: SAMSUNG: use spin_lock_irqsave() in clk_set_parent
In case of error, function module_alloc() in other platform never
returns ERR_PTR(), and all of the user only check for NULL, so
we'd better return NULL instead of ERR_PTR().
dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
GNU Binutils 2.20.1 generates .eh_frame sections that uses R_SPARC_DISP32.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull s390 fixes from Martin Schwidefsky:
"Bug fixes for 3.6-rc7, including some important patches for large page
related memory management issues."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/dasd: fix read unit address configuration loop
s390/dasd: fix pathgroup race
s390/mm: fix user access page-table walk code
s390/hwcaps: do not report high gprs for 31 bit kernel
s390/cio: invalidate cdev pointer before deregistration
s390/cio: fix IO subchannel event race
s390/dasd: move wake_up call
s390/hugetlb: use direct TLB flushing for hugetlbfs pages
s390/mm: fix deadlock in unmap_hugepage_range()
removes unnecessary semicolon
Found by Coccinelle: http://coccinelle.lip6.fr/
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Fix M2P batching re-using the incorrect structure field.
* Disable BIOS SMP MP table search.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQXGfdAAoJEFjIrFwIi8fJbWcH/0FI2d/VyB+ZU0ng3R0Oa7mt
iR/x+Z+mfFdp2dXS6gs6DgJIZVA7i2K9pX4rOXjpDGGGyUeo1xoqjlQfsFWQGjZ/
p49RrDrM93c2GdRXk3iMSWfboQI7BXBs5rnyYZQL7kMxUSR75MxbeONvhPrMSO9I
3EBidWH08qjrn2HVF44F6xh5ONjpclo5AvGIzJ0eU4X0D0eqMnhvlAw8/UYJU2HV
heRvuxWF9l2jNpLhKhZy1730D1X/vKA5qKAcBW8rCOpEijyPpmtKbqapeUJg/9pH
NVquuwGutP5ozrSi7a/23+L+ezvQBmCPm5ZRG44PccBoZ/HVs8haT8UypSWSDzo=
=TwvM
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.6-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
- Fix M2P batching re-using the incorrect structure field.
In v3.5 we added batching for M2P override (Machine Frame Number ->
Physical Frame Number), but the original MFN was saved in an
incorrect structure - and we would oops/restore when restoring with
the old MFN.
- Disable BIOS SMP MP table search.
A bootup issue that we had ignored until we found that on DL380 G6 it
was needed.
* tag 'stable/for-linus-3.6-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/boot: Disable BIOS SMP MP table search.
xen/m2p: do not reuse kmap_op->dev_bus_addr
kcmp has appeared on x86, but has not been noticed because
checksyscalls.sh is broken at the moment. Reserve ARM syscall 378
for this should we ever need it, and add an __IGNORE entry for this
unimplemented syscall.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Exporting KVM exit information to userspace to be consumed by perf.
Signed-off-by: Dong Hao <haodong@linux.vnet.ibm.com>
[ Dong Hao <haodong@linux.vnet.ibm.com>: rebase it on acme's git tree ]
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: kvm@vger.kernel.org
Cc: Runzhen Wang <runzhen@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/1347870675-31495-2-git-send-email-haodong@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
While building the SUSE kernel packages, which build the scripts,
make clean, and then build everything, we have been running into spurious
build failures. We tracked them down to a simple dependency issue:
$ make mrproper
CLEAN arch/x86/tools
CLEAN scripts/basic
$ cp patches/config/x86_64/desktop .config
$ make archscripts
HOSTCC arch/x86/tools/relocs
/bin/sh: scripts/basic/fixdep: No such file or directory
make[3]: *** [arch/x86/tools/relocs] Error 1
make[2]: *** [archscripts] Error 2
make[1]: *** [sub-make] Error 2
make: *** [all] Error 2
This was introduced by commit
6520fe55 (x86, realmode: 16-bit real-mode code support for relocs),
which added the archscripts dependency to archprepare.
This patch adds the scripts_basic dependency to the x86 archscripts.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Silencing build errors and potentially allowing people to use osf
system calls in from processes running in a non-default user namespace.
It seems this stat call was missed in my first round of converting the
stat system calls, bother.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
These ia64 uses of current_uid and current_gid slipped through the
cracks when I was converting everything to kuids and kgids convert
them now.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Convert getresuid, getresgid, getuid, geteuid, getgid, getegid
Convert struct cred kuids and kgids into userspace uids and gids when
returning them.
These s390 system calls slipped through the cracks in my first
round of converstions :(
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Using for_each_set_bit() to simplify the code.
spatch with a semantic match is used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Merged existing board files to a single dt-capable file.
Converted irq and timer code to devicetree.
Removed existing device files that are no longer required with
devicetree support.
All existing platform devices are converted to devicetree nodes
except PWM.
Removed restart.c and moved code into vt8500.c to remove
duplicate PMC code.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Being a module_init call, highbank_pm_init will cause problem with
multi-platform build running on other platforms. Call it from
.init_machine instead.
Reported-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Since the dtb targets have moved to arch/arm/boot/dts/Makefile, sweep
the platforms that have had new targets added recently and move them over.
While I was at it, I also made the dtb generation more generic, i.e. if
the platform is enabled then all dtbs for that platform will be created.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brown <davidb@codeaurora.com>
Cc: Barry Song <Baohua.Song@csr.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
socfpga, picoxcell, and vexpress.
Multi-platform support is dependent on mach/gpio.h removal and
restructuring of DEBUG_LL and dtb build rules included in this branch.
This has been built for all defconfigs, and booted on highbank with
all 5 platforms enabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQU4miAAoJEMhvYp4jgsXi1vMH/A4JJXe24cyo31rHJspZDSFg
nnCbnGKfDEOIHwLA8C3OeJuhswMlP/vWlGC512QXL8903XpZ2VJe63f2CLo1mN7Z
hg3JPWrp2VXZ/bqdMnUcw2CtlylrhyG9MUPapkcp+5Agjz2lwaJtRNL6LRRQX4Ei
cWjsJtaFpRj1QraFna0hpTQNO640je6s1rAIJl6eNOuX08l12ZAGDUA+IUUsa1cA
0OGeOAjH6gmkpMI89j1VPPKVRLHIdP4QcxmAZCHJ2LtvylyrlmYskctpAYibobvt
JPLnZgzMFAegnWtJhOYodhBJlfyypEeh2fsZVyDPowqRz9vaAWRjs6u/I4GYaME=
=HR3H
-----END PGP SIGNATURE-----
Merge tag 'multi-platform-for-3.7' of git://sources.calxeda.com/kernel/linux into next/multiplatform
Enable initial ARM multi-platform support for highbank, mvebu,
socfpga, picoxcell, and vexpress.
Multi-platform support is dependent on mach/gpio.h removal and
restructuring of DEBUG_LL and dtb build rules included in this branch.
This has been built for all defconfigs, and booted on highbank with
all 5 platforms enabled.
By Rob Herring (18) and Arnd Bergmann (1)
via Rob Herring
* tag 'multi-platform-for-3.7' of git://sources.calxeda.com/kernel/linux:
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
ARM: orion: move custom gpio functions to orion-gpio.h
ARM: shmobile: move custom gpio functions to sh-gpio.h
ARM: pxa: use gpio_to_irq for sharppm_sl
net: pxaficp_ir: add irq resources
usb: pxa27x_udc: remove IRQ_USB define
staging: ste_rmi4: remove gpio.h include
Conflicts due to addition of bcm2835 and removal of pnx4008 in:
arch/arm/Kconfig
arch/arm/Makefile
Conflicts due to new dtb targets, moved to arch/arm/boot/dts/Makefile in:
arch/arm/mach-imx/Makefile.boot
arch/arm/mach-mxs/Makefile.boot
arch/arm/mach-tegra/Makefile.boot
Signed-off-by: Olof Johansson <olof@lixom.net>
* next/soc: (50 commits)
ARM: OMAP: AM33xx hwmod: fixup SPI after platform_data move
MAINTAINERS: add an entry for the BCM2835 ARM sub-architecture
ARM: bcm2835: instantiate console UART
ARM: bcm2835: add stub clock driver
ARM: bcm2835: add system timer
ARM: bcm2835: add interrupt controller driver
ARM: add infra-structure for BCM2835 and Raspberry Pi
ARM: tegra20: add CPU hotplug support
ARM: tegra30: add CPU hotplug support
ARM: tegra: clean up the common assembly macros into sleep.h
ARM: tegra: replace the CPU CAR access code by tegra_cpu_car_ops
ARM: tegra: introduce tegra_cpu_car_ops structures
ARM: Tegra: Add smp_twd clock for Tegra20
ARM: AM33XX: clock: Add dcan clock aliases for device-tree
ARM: OMAP2+: dpll: Add missing soc_is_am33xx() check for common functions
ARM: OMAP: omap_device: idle devices with no driver bound
ARM: OMAP: omap_device: don't attempt late suspend if no driver bound
ARM: OMAP: omap_device: keep track of driver bound status
ARM: OMAP3+: hwmod: Add AM33XX HWMOD data
ARM: OMAP2+: hwmod: Hook-up am33xx support in omap_hwmod framework
...
Change/remove conflict in arch/arm/mach-ux500/clock.c resolved.
Signed-off-by: Olof Johansson <olof@lixom.net>
removes unnecessary semicolon
Found by Coccinelle: http://coccinelle.lip6.fr/
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Delete successive assignments to the same location.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression i;
@@
*i = ...;
i = ...;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
