This ensures that only ath9k_hw_set_desc_link needs to recalculate the tx
descriptor checksum on AR9380+
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Makes it easier to clean up the ath9k_hw descriptor API
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During a reset, rx buffers are flushed after rx has been disabled. To avoid
race conditions, rx needs to stay disabled during the reset, so avoid any
calls to ath9k_hw_rxena in that case.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When starting the AP beacon timer, it assumes that the TSF has recently
been cleared. Set the SC_OP_TSF_RESET flag to ensure that this is always
the case.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interrupt handler increases the interrupt disable refcount, so the
tasklet needs to always call ath9k_hw_enable_interrupts.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
in ath_pci_resume it seems we are not enabling LED properly, in addition
we have a PS wrapper fix for this
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
now the LED starts working for AR946/8x chipsets
Cc: "Balasubramanian, senthilkumar" <senthilb@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9003 seems to have issues sometimes with fast channel change
in 5GHz and this case is handled specifically for AR9280 by doing
a full reset. Let's do a full reset for 5GHz channles of AR9380
& for all channels of AR9280 pci chips.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the register macros to appropriate header files to be in
sync with other register definitions and also a single place
to refer everything.
Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for AR946/8x chipets.
Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split tx/rx gain table initval hanlding part so readability
is better and easy to manage the code.
Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add initvals and register modifications required to support AR946/8x chipsets.
Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch reverts commit 9b76883284 which
was introduced in 2.6.38-rc1. It works around a problem where the iwlagn
driver stimulates a bug crashing (requiring power cycle to recover) some
APs under heavy traffic.
CC: stable@kernel.org #2.6.39, #3.0.0 #3.1.0
Signed-off-by: Don Fry <donald.h.fry@intel.com>
SIgned-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The scan request received from cfg80211_connect do not
have proper rate mast. So the probe request sent on each
channel do not have proper the supported rates ie.
Cc: stable@kernel.org
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The eeprom data is stored in little-endian order in the rt2x00 library.
As it was converted to cpu order in the read routines, the data need to
be converted to LE on a big-endian platform.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using gcc 4.4.5 on a Powerbook G4 with a PPC cpu, a complicated
if statement results in incorrect flow, whereas the equivalent switch
statement works correctly.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fix regression introduced by:
commit: ecb4433550
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Fri Aug 12 14:00:59 2011 +0200
mac80211: fix suspend/resume races with unregister hw
Above commit add rtnl_lock() into wiphy_register(), what cause deadlock
when initializing ipw2x00 driver, which itself call wiphy_register()
from register_netdev() internal callback with rtnl mutex taken.
To fix move wiphy_register() outside register_netdev(). This solution
have side effect of not creating /sys/class/net/wlanX/phy80211 link,
but that's a minor issue we can live with.
Bisected-by: Witold Baryluk <baryluk@smp.if.uj.edu.pl>
Bisected-by: Michael Witten <mfwitten@gmail.com>
Tested-by: Witold Baryluk <baryluk@smp.if.uj.edu.pl>
Tested-by: Michael Witten <mfwitten@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During the association, the regulatory is updated by country IE
that reaps the previously found beacons. The impact is that
after a STA disconnects *or* when for any reason a regulatory
domain change happens the beacon hint flag is not cleared
therefore preventing future beacon hints to be learned.
This is important as a regulatory domain change or a restore
of regulatory settings would set back the passive scan and no-ibss
flags on the channel. This is the right place to do this given that
it covers any regulatory domain change.
Cc: stable@kernel.org
Reviewed-by: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The checks for HCI_INQUIRY and HCI_MGMT were in the wrong order,
so that second scans always failed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Normally, the v9 firmware will be loaded if it's available. However, on
OLPC XO-1 machines, the olpc-specific firmware supports extra functionality.
This makes the libertas driver attempt to load the custom firmware first
if the machine is an OLPC machine; if that fails (or it's not an OLPC
machine), fall back to attempting to load the other firmwares.
usb8388_olpc.bin is currently found in the linux-firmware repository.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix kernel-doc warning in net/cfg80211.h:
Warning(include/net/cfg80211.h:1884): No description found for parameter 'registered'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use rt2800_config_wcid and rt2800_delete_wcid_attr to initialize the
WCID table instead of writing to the registers directly.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a STA is not known by the hw (i.e. has no WCID assigned) don't allow
aggregation since this might mess up tx status reports and we won't be
able to distinguish the reports of multiple WCID-less STAs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows us to assign a WCID to each STA even for STAs without
crypto key.
To achieve this search for an unused WCID in the HW WCID table and
assign it to the according STA. When configuring a pairwise key for this
STA we don't need to write the MAC address and BSSIDX anymore but just
update the crypto related fields in the WCID_ATTR table.
This has two advantages:
1) Setting a new key for an already available STA (PTK rekeying) is
slightly less expensive and should improve performance in situations
where a lot of rekeying happens (e.g. a huge number of stations and/or
a small rekeying interval)
2) The TXWI now gets a WCID assigned for unencrypted frames which will
be reflected in the corresponding tx status report. This should make tx
status reports in unencrypted AP mode more reliable as we can
distinguish between multiple key-less STAs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sending an unencrypted frame to a STA the driver might want to pass
a suitable WCID since we don't have a key index to allow tx status
reports to get properly assigned to the correct STA.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a WCID was already assigned to a STA the key configuration
functions need to use the same WCID for configuring the keys. Hence, add
the WCID to the crypo configuration structure.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements a basic sta_add and sta_remove callback. Introduce a new
structure rt2x00_sta and ask mac80211 to allocate it as private part of
its ieee80211_sta. rt2x00_sta only contains the WCID for now.
The sta_add callback allows the driver to assign a WCID to a station
that is currently being added. The same wcid is also passed to the
sta_remove callback one mac80211 removes this STA.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be used by a later patch. No functional changes.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hw.conf.channel value is not updated properly for drivers that
support HW channel switch. Since the switch is done entirely by the
driver and we don't call ieee80211_hw_config(), this value remains
untouched. This patch fixes that by setting the new channel directly in
ieee80211_chswitch_work().
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Per sec 7.1.3.5 of draft 12.0 of 802.11s, mesh frames indicate the
presence of the mesh control header in their QoS header.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to support QoS in mesh, we need to assign queue mapping only
after the next hop has been resolved, both for forwarded and locally
originated frames. Also, now that this is fixed, remove the XXX comment
in ieee80211_select_queue().
Also, V-Shy Ho reported that the queue mapping was not being applied to
the forwarded frame (fwd_skb instead of skb). Fixed that as well.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reading the TX desciptor words from coherent memory is always uncached
and potentially slow. Hence, don't read the TX descriptor prior to
writing it since we update all fields anyway.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800 devices are not capable of configuring arbitrary LED on/off
periods. The LED_CFG register fields ON_PERIOD and OFF_PERIOD are only
used by the hw when the LED mode is set to "blink upon TX".
Hence, remove the blink callback. This will result in software emulation
for LED blinking.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can save an indirect function call + some instructions for fetching
the actual function pointer by passing the driver specific txwi pointer
directly from rt2800pci/rt2800usb to rt2800lib instead of using the
rt2800_drv_get_txwi callback.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The format is intended to be like the subfields
in the QoS Info field, verify that is the case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trivial fixes to allow compilation without warnings when debug
compilation flag isn't set.
Also fix the compilation when debugfs flag isn't set.
Fix a warning: unused priv pointer on the way.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Few lines for program bt_ch_announce being place in the wrong place. Remove those.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When driver detect queue stuck, display current read/write pointer before
perform frimware reload.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reaches encapsulation for this file. In order to reach this:
* move priv->valid_context to iwl_shared
* move the last_rejected initialization to the upper layer
* define a wrapper iwl_nic_config in the upper layer that calls to
cfg->lib->ops->nic_config
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The traffic log debugfs handlers were mistakenly moved to the
transport layer because they print the pointers of the Tx / Rx
queues. The pointers of the queues can be fetched by another debugfs
handler.
So bring the traffic log back to the upper layer and remove the part
that reads the Tx / Rx queues' pointers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move a few declarations needed by the transport layer to iwl-shared.h
Move iwl_cmd_meta, iwl_tx_queue and friends to the internal transport
header file.
Move iwl_device_cmd iwl_host_cmd and friends to iwl-trans.h since
these structs are used in the API to the transport layer.
Move get_cmd_string to the upper layer with a declaration in
iwl-shared.h.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Another round of clean up on the transport layer.
Define a wrapper around wiphy_rfkill_set_hw_state to prevent the
transport layer from accessing priv->hw.
Also move wait_command_queue to the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
