It turns out that some PCI devices require extra delays when changing
power state from D3 to D0 (and the other way around). Although this
is against the PCI specification, we can handle it quite easily by
allowing drivers to define arbitrary D3 delays for devices known to
require extra time for switching power states.
Introduce additional field d3_delay in struct pci_dev and use it to
store the value of the device's D0->D3 delay, in miliseconds. Make
the PCI PM core code use the per-device d3_delay unless
pci_pm_d3_delay is greater (in which case the latter is used).
[This also allows the driver to specify d3_delay shorter than the
10 ms required by the PCI standard if the device is known to be able
to handle that.]
Make the sky2 driver set d3_delay to 150 for devices handled by it.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=14730 which is a
listed regression from 2.6.30.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit 8bf3d79bc401ca417ccf9fc076d3295d1a71dbf5 enabled EEPROM
checksum checks to avoid bogus bug reports but failed to address
updating the code to consider devices with custom EEPROM sizes.
Devices with custom sized EEPROMs have the upper limit size stuffed
in the EEPROM. Use this as the upper limit instead of the static
default size. In case of a checksum error also provide back the
max size and whether or not this was the default size or a custom
one. If the EEPROM is busted we add a failsafe check to ensure
we don't loop forever or try to read bogus areas of hardware.
This closes bug 14874
http://bugzilla.kernel.org/show_bug.cgi?id=14874
Cc: stable@kernel.org
Cc: David Quan <david.quan@atheros.com>
Cc: Stephen Beahm <stephenbeahm@comcast.net>
Reported-by: Joshua Covington <joshuacov@googlemail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If multicast parameter (as returned by zd_op_prepare_multicast) has
changed, no bit in changed_flags is set. To handle this situation, we do
not return if changed_flags is 0. If we do so, we will have some issue
with IPv6 which uses multicast for link layer address resolution.
Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tid is used as an array offset.
agg = &priv->stations[sta_id].tid[tid].agg;
iwl4965_tx_status_reply_tx(priv, agg, tx_resp, txq_id, index);
It should be limitted to MAX_TID_COUNT - 1;
struct iwl_tid_data tid[MAX_TID_COUNT];
regards,
dan carpenter
Signed-off-by: Dan Carpenter <error27@gmail.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If there was an error acquiring the firmware lock in
mwl8k_configure_filter(), we would end up leaking the multicast
command packet prepared by mwl8k_prepare_multicast().
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The unit of sizeof() is byte instead of bit, so fix it.
The patch can fix debug output of some dma_addr_t variables.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add missing DEBUG_FS dependency for ATH9K_DEBUGFS in ath9k's Kconfig.
Signed-off-by: Dominik D. Geyer <dominik.geyer@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
o Fix ethtool link test for NX3031 chip.
o Remove unused code from phy interrupt callback
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Dump registers such as tx ring and rx ring counter, firmware state,
niu regs, etc. which can be useful for debugging purpose.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tx_skbuff is define as:
struct sk_buff *tx_skbuff[TX_RING_ENTRIES];
EVT_RING_ENTRIES is 64 and TX_RING_ENTRIES is 32.
This function is in a error path so that's why it wasn't noticed.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If no break occurred, cnt reaches 0 after the loop.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With `while (--limit > 0)' i reaches 0 after the loop, so upon timeout the
error was not returned.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With `while (--i > 0)' i reaches 0 after the loop, so upon timeout the
error was not issued.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lp->rx_skb has type struct sk_buff **, not struct sk_buff *, so the
elements of the array should have pointer type, not structure type.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@disable sizeof_type_expr@
type T;
T **x;
@@
x =
<+...sizeof(
- T
+ *x
)...+>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should address the problems in version 1 (lazy) and version 2 (ugly).
Bump the stats on orig_dev not on the newly assigned NULL dev variable.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With `while (i++ < MII_TIMEOUT)' i reaches MII_TIMEOUT + 1 after the loop
This is probably unlikely a problem in practice.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test the just-allocated value for NULL rather than some other value.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,y;
statement S;
@@
x = \(kmalloc\|kcalloc\|kzalloc\)(...);
(
if ((x) == NULL) S
|
if (
- y
+ x
== NULL)
S
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
velocity_open() calls velocity_give_many_rx_descs(), which gives RX
descriptors to the NIC, before installing an interrupt handler or
calling velocity_init_registers(). I think this is very unsafe and it
appears to explain the bug report <http://bugs.debian.org/508527>.
On MTU change, velocity_give_many_rx_descs() is again called before
velocity_init_registers(). I'm not sure whether this is unsafe but
it does look wrong.
Therefore, move the calls to velocity_give_many_rx_descs() after
request_irq() and velocity_init_registers().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Jan Ceuleers <jan.ceuleers@computer.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use a rather complicated logic to support eTSEC and eTSEC2.0
registers maps in a single driver. Currently, the code tries to
unmap 'regs', but for non-eTSEC2.0 controllers 'regs' doesn't
point to a mapping start, and this might cause badness on probe
failure or module removal:
Freescale PowerQUICC MII Bus: probed
Trying to vfree() nonexistent vm area (e107f000)
------------[ cut here ]------------
Badness at c00a7754 [verbose debug info unavailable]
NIP: c00a7754 LR: c00a7754 CTR: c02231ec
[...]
NIP [c00a7754] __vunmap+0xec/0xf4
LR [c00a7754] __vunmap+0xec/0xf4
Call Trace:
[df827e50] [c00a7754] __vunmap+0xec/0xf4 (unreliable)
[df827e70] [c001519c] iounmap+0x44/0x54
[df827e80] [c028b924] fsl_pq_mdio_probe+0x1cc/0x2fc
[df827eb0] [c02fb9b4] of_platform_device_probe+0x5c/0x84
[df827ed0] [c0229928] really_probe+0x78/0x1a8
[df827ef0] [c0229b20] __driver_attach+0xa4/0xa8
Fix this by introducing a proper priv structure (finally!), which
now holds 'regs' and 'map' fields separately.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes ucc_geth fails to suspend with the following trace:
ucc_geth e0103000.ucc: suspend
ucc_geth e0102000.ucc: suspend
NETDEV WATCHDOG: eth0 (ucc_geth): transmit queue 0 timed out
------------[ cut here ]------------
Badness at net/sched/sch_generic.c:255
NIP: c021cb5c LR: c021cb5c CTR: c01ab4b4
[...]
NIP [c021cb5c] dev_watchdog+0x298/0x2a8
LR [c021cb5c] dev_watchdog+0x298/0x2a8
Call Trace:
[c0389da0] [c021cb5c] dev_watchdog+0x298/0x2a8 (unreliable)
[c0389e00] [c0031ed8] run_timer_softirq+0x16c/0x1dc
[c0389e50] [c002c638] __do_softirq+0xa4/0x11c
[...]
This patch fixes the issue by properly detaching the device on
suspend, and attaching it back on resume.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hibernation assumes power loss, we should fully reinitialize
PHYs (including platform fixups), as if PHYs were just attached.
This patch factors phy_init_hw() out of phy_attach_direct(), then
converts mdio_bus to dev_pm_ops and adds an appropriate restore()
callback.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes kernel hangs on resume with the following trace:
ucc_geth e0102000.ucc: resume
INFO: task bash:1764 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
bash D 0fecf43c 0 1764 1763 0x00000000
Call Trace:
[cf9a7c10] [c0012868] ret_from_except+0x0/0x14 (unreliable)
--- Exception: cf9a7ce0 at __switch_to+0x4c/0x6c
LR = 0xcf9a7cc0
[cf9a7cd0] [c0008c14] __switch_to+0x4c/0x6c (unreliable)
[cf9a7ce0] [c028bcfc] schedule+0x158/0x260
[cf9a7d10] [c028c720] __mutex_lock_slowpath+0x80/0xd8
[cf9a7d40] [c01cf388] phy_stop+0x20/0x70
[cf9a7d50] [c01d514c] ugeth_resume+0x6c/0x13c
[...]
Here is why.
On suspend:
- PM core starts suspending devices, ucc_geth_suspend gets called;
- ucc_geth calls phy_stop() on suspend. Note that phy_stop() is
mostly asynchronous so it doesn't block ucc_geth's suspend routine,
it just sets PHY_HALTED state and disables PHY's interrupts;
- Suddenly the state machine gets scheduled, it grabs the phydev->lock
mutex and tries to process the PHY_HALTED state, so it calls
phydev->adjust_link(phydev->attached_dev). In ucc_geth case
adjust_link() calls msleep(), which reschedules the code flow back to
PM core, which now finishes suspend and so we end up sleeping with
phydev->lock mutex held.
On resume:
- PM core starts resuming devices (notice that nobody rescheduled
the state machine yet, so the mutex is still held), the core calls
ucc_geth's resume routine;
- ucc_geth_resume restarts the PHY with phy_stop()/phy_start()
sequence, and the phy_*() calls are trying to grab the phydev->lock
mutex. Here comes the deadlock.
This patch fixes the issue by stopping the state machine on suspend
and starting it again on resume.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (74 commits)
Revert "b43: Enforce DMA descriptor memory constraints"
iwmc3200wifi: fix array out-of-boundary access
wl1251: timeout one too soon in wl1251_boot_run_firmware()
mac80211: fix propagation of failed hardware reconfigurations
mac80211: fix race with suspend and dynamic_ps_disable_work
ath9k: fix missed error codes in the tx status check
ath9k: wake hardware during AMPDU TX actions
ath9k: wake hardware for interface IBSS/AP/Mesh removal
ath9k: fix suspend by waking device prior to stop
cfg80211: fix error path in cfg80211_wext_siwscan
wl1271_cmd.c: cleanup char => u8
iwlwifi: Storage class should be before const qualifier
ath9k: Storage class should be before const qualifier
cfg80211: fix race between deauth and assoc response
wireless: remove remaining qual code
rt2x00: Add USB ID for Linksys WUSB 600N rev 2.
ath5k: fix SWI calibration interrupt storm
mac80211: fix ibss join with fixed-bssid
libertas: Remove carrier signaling from the scan code
orinoco: fix GFP_KERNEL in orinoco_set_key with interrupts disabled
...
Allocate priv->rx_packets[IWM_RX_ID_HASH + 1] because the max array
index is IWM_RX_ID_HASH according to IWM_RX_ID_GET_HASH().
Cc: stable@kernel.org
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
`loop' reaches INIT_LOOP + 1 after the loop. so if ACX_INTR_INIT_COMPLETE
occurs in the last iteration the write occurs but also the error out as if a
timeout occurred. This is probably very unlikely to ever occur.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My previous change added in:
commit 815833e7ec
ath9k: fix tx status reporting
was not checking all possible tx error conditions. This could possibly
lead to throughput issues due to slow rate control adaption or missed
retransmissions of failed A-MPDU frames.
This patch adds a mask for all possible error conditions and uses it
in the xmit ok check.
Cc: stable@kernel.org
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AMDPDU actions poke hardware for TX operation, as such
we want to turn hardware on for these actions. AMDPU RX operations
do not require hardware on as nothing is done in hardware for
those actions. Without this we cannot guarantee hardware has
been programmed correctly for each AMPDU TX action.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we remove a IBSS/AP/Mesh interface we stop DMA
but to do this we should ensure hardware is on. Awaken
the device prior to these calls. This should ensure
DMA is stopped upon suspend and plain device removal.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure the device is awake prior to trying to tell hardware
to stop it. Impact of not doing this is we can likely leave
the device in an undefined state likely causing issues with
suspend and resume. This patch ensures harware is where it
should be prior to suspend.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is just a clean up and doesn't make a functional difference. It keeps the
lint checkers happy.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the remaining users of the rx status
'qual' field and the field itself.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a rt2870 based device.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The calibration period is now invoked by triggering a software
interrupt from within the ISR by ath5k_hw_calibration_poll()
instead of via a timer.
However, the calibration interval isn't initialized before
interrupts are enabled, so we can have a situation where an
interrupt occurs before the interval is assigned, so the
interval is actually negative. As a result, the ISR will
arm a software interrupt to schedule the tasklet, and then
rearm it when the SWI is processed, and so on, leading to a
softlockup at modprobe time.
Move the initialization order around so the calibration interval
is set before interrupts are active. Another possible fix
is to schedule the tasklet directly from the poll routine,
but I think there are additional plans for the SWI.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no reason to signal a carrier off when doing a 802.11 scan.
Cc: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few lines earlier we assume that best->slave could be either null or non-null so
we should check it here as well.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f001fde5ea changed
net_device.dev_addr from a 32-byte array to a pointer.
I found 4 ethernet drivers which rely on sizeof(dev_addr), which are now
only copying 4 bytes of the address information on 32bit systems.
Fix them to use ETH_ALEN.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gfar_select_queue() function was used to set queue mapping
only for forwarding/bridging applications and the condition
for locally generated packets was completely ignored.
The solution is to remove the gfar_select_queue() function and
use skb_record_rx_queue to set queue mapping for
forwarding/bridging applications. This will ensure that in case of
forwarding/bridging applications txq = rxq will be selected and
skb_tx_hash will be used to pick up a txq for locally generated packets.
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using macro tun_sk is more clear and shorter. However tun.c has tun_sk,
but doesn't use it.
Signed-off-by: Vitaliy Gusev <vgusev@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If PHY doesn't have an IRQ, phylib would poll for link changes, and
would call adjust_link() every second. In that case we disable and
enable the controller every second.
Let's better check if there is actually anything changed, and, if so,
change the MAC settings.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 864fdf884e ("ucc_geth:
Fix hangs after switching from full to half duplex") ucc_geth driver
disables the controller during MAC configuration changes. Though,
disabling the controller might take quite awhile, and so the netdev
watchdog might get upset:
NETDEV WATCHDOG: eth2 (ucc_geth): transmit queue 0 timed out
------------[ cut here ]------------
Badness at c02729a8 [verbose debug info unavailable]
NIP: c02729a8 LR: c02729a8 CTR: c01b6088
REGS: c0451c40 TRAP: 0700 Not tainted (2.6.32-trunk-8360e)
[...]
NIP [c02729a8] dev_watchdog+0x280/0x290
LR [c02729a8] dev_watchdog+0x280/0x290
Call Trace:
[c0451cf0] [c02729a8] dev_watchdog+0x280/0x290 (unreliable)
[c0451d50] [c00377c4] run_timer_softirq+0x164/0x224
[c0451da0] [c0032a38] __do_softirq+0xb8/0x13c
[c0451df0] [c00065cc] do_softirq+0xa0/0xac
[c0451e00] [c003280c] irq_exit+0x7c/0x9c
[c0451e10] [c00640c4] __ipipe_sync_stage+0x248/0x24c
[...]
This patch fixes the issue by detaching the netdev during the
time we change the configuration.
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Cc: Stable <stable@vger.kernel.org> [2.6.32]
Signed-off-by: David S. Miller <davem@davemloft.net>
Following oops was seen with the ucc_geth driver:
Unable to handle kernel paging request for data at address 0x00000058
Faulting instruction address: 0xc024f2fc
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c024f2fc] skb_recycle_check+0x14/0x100
LR [e30aa0a4] ucc_geth_poll+0xd8/0x4e0 [ucc_geth_driver]
Call Trace:
[df857d50] [c000b03c] __ipipe_grab_irq+0x3c/0xa4 (unreliable)
[df857d60] [e30aa0a4] ucc_geth_poll+0xd8/0x4e0 [ucc_geth_driver]
[df857dd0] [c0258cf8] net_rx_action+0xf8/0x1b8
[df857e10] [c0032a38] __do_softirq+0xb8/0x13c
[df857e60] [c00065cc] do_softirq+0xa0/0xac
[...]
This is because ucc_geth_tx() tries to process an empty queue when
queues are logically stopped. Stopping the queues doesn't disable
polling, and since nowadays ucc_geth_tx() is actually called from
the polling routine, the oops above might pop up.
Fix this by removing 'netif_queue_stopped() == 0' check.
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Cc: Stable <stable@vger.kernel.org> [2.6.32]
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device is reset during MTU change, ring size change, or self
test, etc, the cnic status block needs to be properly initialized if
cnic is registered.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are BUGs "scheduling while atomic" triggered by the timer
rhine_tx_timeout(). They are caused by calling napi_disable() (with
msleep()). This patch fixes it by moving most of the timer content to
the workqueue function (similarly to other drivers, like tg3), with
spin_lock() changed to BH version.
Additionally, there is spin_lock_irq() moved in rhine_close() to
exclude napi_disable() etc., also tg3's way.
Reported-by: Andrey Rahmatullin <wrar@altlinux.org>
Tested-by: Andrey Rahmatullin <wrar@altlinux.org>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a pci_save_state() call in ixgbe_resume() after
pci_restore_state(). A similar change was made in ixgbe_io_slot_reset()
that accommodates pci_restore_state() new behavior. This change makes
pci_restore_state() clear the saved_state flag This is necessary due
to a resent kernel change to pci_restore_state() so that it now clears
the saved_state flag of the device right after the device.s standard
configuration registers have been poplulated with the previously saved
values.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to return correct values for transceiver and supported in
ethtool get_settings function.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIC controller has to be set to an appropriate mode before doing a loopback
test. Test will fail otherwise.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change ensures that loopback test command gives up after 4 seconds when
the hardware is not responsive. This could happen if the ports are connected
properly in loopback mode.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool code for enabling Wake on Lan was not correctly checking the
status register bits so as a result ports 0 and 2 were both being allowed
to set WOL to enabled even though it is only supported on the first port
for our adapters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The watermark values for the 82575 were not being set correctly. As a
result the high and low watermark values were set to the same value which
can lead to excess xon/xoff packets being generated.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change resolves an issue seen in some configurations where the link
may drop to 100Mb/s even though the link itself supports 1000Mb/s. The
issue was root caused to the fact that we were only trying the link once.
Now instead we will try up to 5 attempts on a faulty cable before
downshifting to 100Mb/s.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were forcing the PCS link up in error when we are in KX mode. We should
only be disabling autoneg, not forcing the link up.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This hardware watchdog can misfire, so it does more harm than good.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some cables have EEPROMs that conflict with the PHY's on-board EEPROM
so it cannot load firmware.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY's firmware very occasionally appears to lock up very early, but
with the heartbeat update still running. Rebooting the microcontroller
core seems to be sufficient to recover.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY boots in a mode which is not necessarily optimal. This change
switches it to self-configure mode (except when in loopback, which
won't work in that mode if an SFP+ module is not present) by rebooting
the PHY's microcontroller, and replicating the sequence of configuration
writes from the boot EEPROM with the appropriate changes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we see the PHY remaining stuck in a link-down state due to PCS being
down while PMA/PMD is up, we briefly switch to PMA/PMD loopback and back,
which usually unsticks it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need buffer->len to remain valid to work out the correct address to
be unmapped. We therefore need to clear buffer->len after the unmap
operation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The XGXS block may not get a link immediately in XGXS or XAUI loopback
modes, so we still need to check it. Split falcon_xaui_link_ok() into
falcon_xgxs_link_ok(), which checks only the Falcon XGXS block, and
falcon_xmac_link_ok(), which checks one or both sides of the link as
appropriate. Also rename falcon_check_xaui_link() to
falcon_xmac_link_ok_retry().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This prevents efx->link_advertising from being blatted during
a reset.
The phy_short_reach sysfs node is now destroyed later in the
port shutdown process, so check for STATE_RUNNING after
acquiring the rtnl_lock (just like in set_phy_flash_cfg).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the "ignoring return value of '...', declared with attribute
warn_unused_result" compiler warning in several users of the new kfifo
API.
It removes the __must_check attribute from kfifo_in() and
kfifo_in_locked() which must not necessary performed.
Fix the allocation bug in the nozomi driver file, by moving out the
kfifo_alloc from the interrupt handler into the probe function.
Fix the kfifo_out() and kfifo_out_locked() users to handle a unexpected
end of fifo.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rename kfifo_put... into kfifo_in... to prevent miss use of old non in
kernel-tree drivers
ditto for kfifo_get... -> kfifo_out...
Improve the prototypes of kfifo_in and kfifo_out to make the kerneldoc
annotations more readable.
Add mini "howto porting to the new API" in kfifo.h
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the pointer to the spinlock out of struct kfifo. Most users in
tree do not actually use a spinlock, so the few exceptions now have to
call kfifo_{get,put}_locked, which takes an extra argument to a
spinlock.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a new generic kernel FIFO implementation.
The current kernel fifo API is not very widely used, because it has to
many constrains. Only 17 files in the current 2.6.31-rc5 used it.
FIFO's are like list's a very basic thing and a kfifo API which handles
the most use case would save a lot of development time and memory
resources.
I think this are the reasons why kfifo is not in use:
- The API is to simple, important functions are missing
- A fifo can be only allocated dynamically
- There is a requirement of a spinlock whether you need it or not
- There is no support for data records inside a fifo
So I decided to extend the kfifo in a more generic way without blowing up
the API to much. The new API has the following benefits:
- Generic usage: For kernel internal use and/or device driver.
- Provide an API for the most use case.
- Slim API: The whole API provides 25 functions.
- Linux style habit.
- DECLARE_KFIFO, DEFINE_KFIFO and INIT_KFIFO Macros
- Direct copy_to_user from the fifo and copy_from_user into the fifo.
- The kfifo itself is an in place member of the using data structure, this save an
indirection access and does not waste the kernel allocator.
- Lockless access: if only one reader and one writer is active on the fifo,
which is the common use case, no additional locking is necessary.
- Remove spinlock - give the user the freedom of choice what kind of locking to use if
one is required.
- Ability to handle records. Three type of records are supported:
- Variable length records between 0-255 bytes, with a record size
field of 1 bytes.
- Variable length records between 0-65535 bytes, with a record size
field of 2 bytes.
- Fixed size records, which no record size field.
- Preserve memory resource.
- Performance!
- Easy to use!
This patch:
Since most users want to have the kfifo as part of another object,
reorganize the code to allow including struct kfifo in another data
structure. This requires changing the kfifo_alloc and kfifo_init
prototypes so that we pass an existing kfifo pointer into them. This
patch changes the implementation and all existing users.
[akpm@linux-foundation.org: fix warning]
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
bnx2: Fix bnx2_netif_stop() merge error.
gianfar: Fix bit definitions of IMASK_GRSC and IMASK_GTSC
gianfar: Fix stats support
gianfar: Fix a filer bug
bnx2: fixing a timout error due not refreshing TX timers correctly
can/at91: don't check platform_get_irq's return value against zero
mISDN: use DECLARE_COMPLETION_ONSTACK for non-constant completion
bnx2: reset_task is crashing the kernel. Fixing it.
ipv6: fix an oops when force unload ipv6 module
TI DaVinci EMAC: Fix MDIO bus frequency configuration
e100: Fix broken cbs accounting due to missing memset.
broadcom: bcm54xx_shadow_read() errors ignored in bcm54xx_adjust_rxrefclk()
e1000e: LED settings in EEPROM ignored on 82571 and 82572
netxen: use module parameter correctly
netns: fix net.ipv6.route.gc_min_interval_ms in netns
Bluetooth: Prevent ill-timed autosuspend in USB driver
Bluetooth: Fix L2CAP locking scheme regression
Bluetooth: Ack L2CAP I-frames before retransmit missing packet
Bluetooth: Fix unset of RemoteBusy flag for L2CAP
Bluetooth: Fix PTR_ERR return of wrong pointer in hidp_setup_hid()
The option to support the old style PSK interface in the PS3
GELIC wireless drivers requires CONFIG_WEXT_PRIV to be set
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I noticed yesterday, because Jeff had noticed
a speed regression, cf. bug
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2138
that the SM PS settings for peers were wrong.
Instead of overwriting the SM PS settings with
the local bits, we need to keep the remote bits.
The bug was part of the original HT code from
over two years ago, but unfortunately nobody
noticed that it makes no sense -- we shouldn't
be overwriting the peer's setting with our own
but rather keep it intact when masking the peer
capabilities with our own.
While fixing that, I noticed that the masking of
capabilities is completely useless for most of
the bits, so also fix those other bits.
Finally, I also noticed that PSMP_SUPPORT no
longer exists in the final 802.11n version, so
also remove that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
`queue' was unsigned so the test did not work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Reviewed-by: Pavel Roskin <proski@gnu.org>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The libertas driver copies the SSID buffer back to the wireless core and
appends a trailing NULL character for termination. This is
a) unnecessary because the buffer is allocated with kzalloc and is hence
already NULLed when this function is called, and
b) for priv->curbssparams.ssid_len == 32, it writes back one byte too
much which causes memory corruptions.
Fix this by removing the extra write.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Maithili Hinge <maithili@marvell.com>
Cc: Kiran Divekar <dkiran@marvell.com>
Cc: Michael Hirsch <m.hirsch@raumfeld.com>
Cc: netdev@vger.kernel.org
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@lists.infradead.org
Cc: stable@kernel.org
Acked-by: Holger Schurig <holgerschurig@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/iwlwifi/iwl-tx.c: In function `iwl_hw_txq_ctx_free':
drivers/net/wireless/iwlwifi/iwl-tx.c:410: warning: suggest explicit braces to avoid ambiguous `else'
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MIB counters are disabled when doing a chip reset.
Since ANI depends on the MIB registers for its operation, relying
on the contents of said registers during HW reset results in sub-optimal
performance.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When TX DMA termination has failed, the HW has to be reset
completely. Doing a fast channel change in this case is insufficient.
Also, change the debug level of a couple of messages to FATAL.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The internal, driver-specific maintenance of sequence
numbers is applicable only for HT frames.
Also, remove comments that are not relevant anymore.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix typo. The index should be multiplied by the entry size, not 'and'-ed.
Found via code-inspection.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices have 40MHz operation disabled entirely. Ensure that driver do
not enable 40MHz operation if a channel does not allow this.
This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2135
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent powersaving work resulted in power management ops being called
during EEPROM initialization. The lock used by these functions is not
initialized at this time. Ensure lock is initialized before it is used.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we see from http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2125
that power saving does not work well on 3945. Since then power saving has
also been connected with association problems where an AP deathenticates a
3945 after it is unable to transmit data to it - this happens when 3945
enters power savings mode.
Disable power save support until issues are resolved.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I've also for a long time had a problem with the
temperature calculation code, which I had fixed
by byte-swapping the values, and now it turns out
that was the correct fix after all.
Also, any use of iwl_eeprom_query_addr() that is
for more than a u8 must be cast to little endian,
and some structs as well.
Fix all this. Again, no real impact on platforms
that already are little endian.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The construct "le16_to_cpu((__force __le16)(r >> 16))" has
always bothered me when looking through the iwlwifi code,
it shouldn't be necessary to __force anything, and before
this code, "r" was obtained with an ioread32, which swaps
each of the two u16 values in it properly when swapping the
entire u32 value. I've had arguments about this code with
people before, but always conceded they were right because
removing it only made things not work at all on big endian
platforms.
However, analysing a failure of the OTP reading code, I now
finally figured out what is going on, and why my intuition
about that code being wrong was right all along.
It turns out that the 'priv->eeprom' u8 array really wants
to have the data in it in little endian. So the force code
above and all really converts *to* little endian, not from
it. Cf., for instance, the function iwl_eeprom_query16() --
it reads two u8 values and combines them into a u16, in a
little-endian way. And considering it more, it makes sense
to have the eeprom array as on the device, after all not
all values really are 16-bit values, the MAC address for
instance is not.
Now, what this really means is that all the annotations are
completely wrong. The eeprom reading code should fill the
priv->eeprom array as a __le16 array, with __le16 values.
This also means that iwl_read_otp_word() should really have
a __le16 pointer as the data argument, since it should be
filling that in a format suitable for priv->eeprom.
Propagating these changes throughout, iwl_find_otp_image()
is found to be, now obviously visible, defective -- it uses
the data returned by iwl_read_otp_word() directly as if it
was CPU endianness. Fixing that, which is this hunk of the
patch:
- next_link_addr = link_value * sizeof(u16);
+ next_link_addr = le16_to_cpu(link_value) * sizeof(u16);
is the only real change of this patch. Everything else is
just fixing the sparse annotations.
Also, the bug only shows up on big endian platforms with a
1000 series card. 5000 and previous series do not use OTP,
and 6000 series has shadow RAM support which means we don't
ever use the defective code on any cards but 1000.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've had many reports of rt61pci failures with powersaving enabled.
Therefore, as a stop-gap measure, disable powersaving of the rt61pci
until we have found a proper solution.
Also disable powersaving on rt2800pci as it most probably will show
the same problem.
Cc: stable@kernel.org
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sizeof(iv16) and sizeof(iv32) are the sizes of pointers. Change them to
the size of the copied data.
Furthermore, iveiv_entry is a local structure that has just been
initialized and is not visible outside this function. Thus, there would
seem to be no point to copy data into it. The order of the arguments is
thus changed to copy the data into the parameters, which are provided as
pointers, suggesting in this case that they should be used to return values.
A simplified version of the semantic patch that finds the first problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
expression f;
type T;
@@
*f(...,(T)x,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
First, we copy/paste the padding stuff from ath9k_tx to ath_tx_cabq since it
needs to same kind of padding, but for internally generated beacons.
Next, software padding done on TX needs to be removed before calling
ieee80211_tx_status. The code was already there in ath_tx_complete but it
was wrong. Fix it by using ath9k_cmn_padpos. This later code has been
tested by sending packets to a monitor interface and reading packets from the
same interface.
Signed-off-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When trigger event log dumping from debugfs, the entire event log
should be dumped and the size should match the number of events being
dump.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent commits "iwlwifi: remove power-wasting calls to apm_ops.init()" and
"iwlagn: power up device before initializing EEPROM" had the goal of
reducing device power consumption from the time the module is loaded until
the interface is brought up and the device's power saving mechanisms kick
in. The idea is that once the module is loaded there is no need for the
device to consume power until the interface is brought up.
With the current solution the device is only powered up during EEPROM read,
and then so also only if the EEPROM type is OTP. We have found that on
certain platforms even non-OTP devices require power to be up during EEPROM
read. On these platforms the driver never loads and the system log contains
the following:
iwlagn 0000:03:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0x080403D8
We thus now power up all devices during EEPROM read.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In iwlwifi, priv->alloc_rxb_page is used to keep track of the Rx
pages allocated by the driver. This cleans up the page free routines
by introducing __iwl_free_pages/iwl_free_pages so that the accounting
is more accurate and less error prone. This also fixes two instances where
the counter was not updated.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The error was introduced while merging:
commit 4529819c45
bnx2: reset_task is crashing the kernel. Fixing it.
Signed-off-by: Michael Chan <mchan@broadcom.com>k
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the per rx/tx queue stats.
To update the per rx queue stats a new structure has been
introduced rx_q_stats.
The per tx queue stats are updated via the netdev_queue
structure itself.
Note that we update only the tx_packtes, tx_bytes, rx_packets,
rx_bytes and rx_dropped stats on a per queue basis.
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to enable filer whenever we need to use multiple RX
queues. Also, need to program RIR0 register with the required
distribution we require, if using RX filer hashing support for
packet distribution to multiple queues.
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running the following script on an active bnx2 interface:
while(true); do ifconfig ethX mtu 9000; ifconfig ethX mtu 1500; done
A timeout error appears and dumps the following stack:
NETDEV WATCHDOG: eth4 (bnx2): transmit queue 0 timed out
------------[ cut here ]------------
Badness at net/sched/sch_generic.c:261
<snip>
This patch just fixes the way that ->trans_start is refreshed.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
