It can be useful for DSA and CPU ports to have a phy-mode property, in
particular to specify RGMII delays. Parse the property and set it in
the fixed-link phydev.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, DSA and CPU ports are configured to the maximum speed the
switch supports. However there can be use cases where the peer devices
port is slower. Allow a fixed-link property to be used with the DSA
and CPU port in the device tree, and use this information to configure
the port.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With more than two switches in a hierarchy, it becomes necessary to
describe multi-hop routes between switches. The current binding does
not allow this, although the older platform_data did. Extend the link
property to be a list rather than a single phandle to a remote switch.
It is then possible to express that a port should be used to reach
more than one switch and the switch maybe more than one hop away.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new functions in DSA drivers to access hardware VLAN entries through
SWITCHDEV_OBJ_PORT_VLAN objects:
- port_pvid_get() and vlan_getnext() to dump a VLAN
- port_vlan_del() to exclude a port from a VLAN
- port_pvid_set() and port_vlan_add() to join a port to a VLAN
The DSA infrastructure will ensure that each VLAN of the given range
does not already belong to another bridge. If it does, it will fallback
to software VLAN and won't program the hardware.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cavium/Kconfig
The cavium conflict was overlapping dependency
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we need to divert reads/writes using the slave MII bus, we may have
already fetched a valid PHY interface property from Device Tree, and that
mode is used by the PHY driver to make configuration decisions.
If we could not fetch the "phy-mode" property, we will assign p->phy_interface
to PHY_INTERFACE_MODE_NA, such that we can actually check for that condition as
to whether or not we should override the interface value.
Fixes: 19334920ea ("net: dsa: Set valid phy interface type")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the switchdev_port_obj_{add,del,dump} functions in DSA to
support the SWITCHDEV_OBJ_PORT_FDB objects.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the prototype of port_getnext to include a vid parameter.
This is necessary to introduce the support for VLAN.
Also rename the fdb_{add,del,getnext} function pointers to
port_fdb_{add,del,getnext} since they are specific to a given port.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using a cluster of switches, some topologies will have an MDIO
bus per switch, not one for the whole cluster. Allow this to be
represented in the device tree, by adding an optional mii-bus property
at the switch level. The old platform_device method of instantiation
supports this already, so only the device tree binding needs extending
with an additional optional phandle.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the fdb_{add,del,getnext} function pointer in favor of new
port_fdb_{add,del,getnext}.
Implement the switchdev_port_obj_{add,del,dump} functions in DSA to
support the SWITCHDEV_OBJ_PORT_FDB objects.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for using DSA slave network devices with netconsole, which
requires us to allocate and free custom netpoll instances and invoke the
parent network device poll controller callback.
In order for netconsole to work, we need to construct the DSA tag, but
not queue the skb for transmission on the master network device xmit
function.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All tagging protocols do the same thing: increment device statistics,
make room for the tag to be inserted, create the tag, invoke the parent
network device transmit function.
In order to prepare for adding netpoll support, which requires the tag
creation, but not using the parent network device transmit function, do
some little refactoring which eliminates duplication between the 4
tagging protocols supported.
We need to return a sk_buff pointer back to the caller because the tag
specific transmit function may have to reallocate the original skb (e.g:
tag_trailer.c) and this is the one we should be transmitting, not the
original sk_buff we were passed.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cd->sw_addr is used as a MDIO bus address, which cannot exceed
PHY_MAX_ADDR (32), our check was off-by-one.
Fixes: 5e95329b70 ("dsa: add device tree bindings to register DSA switches")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
port_index is used an index into an array, and this information comes
from Device Tree, make sure that port_index is not equal to the array
size before using it. Move the check against port_index earlier in the
loop.
Fixes: 5e95329b70: ("dsa: add device tree bindings to register DSA switches")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA master netdev promiscuity counter was not being properly
decremented on slave device open error path.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
CC: Gilad Ben-Yossef <giladb@ezchip.com>
CC: David S. Miller <davem@davemloft.net>
CC: Florian Fainelli <f.fainelli@gmail.com>
CC: Guenter Roeck <linux@roeck-us.net>
CC: Andrew Lunn <andrew@lunn.ch>
CC: Scott Feldman <sfeldma@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
While shuffling some code around, dsa_switch_setup_one() was introduced,
and it was modified to return either an error code using ERR_PTR() or a
NULL pointer when running out of memory or failing to setup a switch.
This is a problem for its caler: dsa_switch_setup() which uses IS_ERR()
and expects to find an error code, not a NULL pointer, so we still try
to proceed with dsa_switch_setup() and operate on invalid memory
addresses. This can be easily reproduced by having e.g: the bcm_sf2
driver built-in, but having no such switch, such that drv->setup will
fail.
Fix this by using PTR_ERR() consistently which is both more informative
and avoids for the caller to use IS_ERR_OR_NULL().
Fixes: df197195a5 ("net: dsa: split dsa_switch_setup into two functions")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older gcc versions (e.g. gcc version 4.4.6) don't like anonymous unions
which was causing build issues on the newly added switchdev attr/obj
structs. Fix this by using named union on structs.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
STP update is just a settable port attribute, so convert
switchdev_port_stp_update to an attr set.
For DSA, the prepare phase is skipped and STP updates are only done in the
commit phase. This is because currently the DSA drivers don't need to
allocate any memory for STP updates and the STP update will not fail to HW
(unless something horrible goes wrong on the MDIO bus, in which case the
prepare phase wouldn't have been able to predict anyway).
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch ID is just a gettable port attribute. Convert switchdev op
switchdev_parent_id_get to a switchdev attr.
Note: for sysfs and netlink interfaces, SWITCHDEV_ATTR_PORT_PARENT_ID is
called with SWITCHDEV_F_NO_RECUSE to limit switch ID user-visiblity to only
port netdevs. So when a port is stacked under bond/bridge, the user can
only query switch id via the switch ports, but not via the upper devices
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turned out that "switchdev" sticks. So just unify all related terms to use
this prefix.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA stacks an Ethernet device on top of an Ethernet device. This can
cause false positive lockdep splats for the transmit queue:
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
=============================================
[ INFO: possible recursive locking detected ]
4.0.0-rc7-01838-g70621a215fc7 #386 Not tainted
---------------------------------------------
kworker/0:0/4 is trying to acquire lock:
(_xmit_ETHER#2){+.-...}, at: [<c040e95c>] sch_direct_xmit+0xa8/0x1fc
but task is already holding lock:
(_xmit_ETHER#2){+.-...}, at: [<c03f4208>] __dev_queue_xmit+0x4d4/0x56c
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(_xmit_ETHER#2);
lock(_xmit_ETHER#2);
To avoid this, walk the tq queues of the dsa slaves and set a lockdep
class.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
eeprom-length is a switch property, not a dsa property, and thus
needs to be attached to the switch node, not to the dsa node.
Reported-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 6793abb4e8 ("net: dsa: Add support for switch EEPROM access")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit da4759c (sysfs: Use only return value from is_visible for
the file mode), it is possible to reduce the permissions of a file.
So declare temp1_max with the DEVICE_ATTR_RW macro and remove the write
permission in dsa_hwmon_attrs_visible if set_temp_limit isn't provided.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mellanox/mlx4/cmd.c
net/core/fib_rules.c
net/ipv4/fib_frontend.c
The fib_rules.c and fib_frontend.c conflicts were locking adjustments
in 'net' overlapping addition and removal of code in 'net-next'.
The mlx4 conflict was a bug fix in 'net' happening in the same
place a constant was being replaced with a more suitable macro.
Signed-off-by: David S. Miller <davem@davemloft.net>
According to description in 'include/net/dsa.h', in cascade switches
configurations where there are more than one interconnected devices,
'rtable' array in 'dsa_chip_data' structure is used to indicate which
port on this switch should be used to send packets to that are destined
for corresponding switch.
However, dsa_of_setup_routing_table() fills 'rtable' with port numbers
of the _target_ switch, but not current one.
This commit removes redundant devicetree parsing and adds needed port
number as a function argument. So dsa_of_setup_routing_table() now just
looks for target switch number by parsing parent of 'link' device node.
To remove possible misunderstandings with the way of determining target
switch number, a corresponding comment was added to the source code and
to the DSA device tree bindings documentation file.
This was tested on a custom board with two Marvell 88E6095 switches with
following corresponding routing tables: { -1, 10 } and { 8, -1 }.
Signed-off-by: Pavel Nakonechny <pavel.nakonechny@skitlab.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't use dev->iflink anymore.
CC: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide callbacks for ndo_fdb_add, ndo_fdb_del, and ndo_fdb_dump.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Master change notifications may occur other than when joining or
leaving a bridge, for example when being added to or removed from
a bond or Open vSwitch. In that case, do nothing instead of asking
the switch driver to remove a port from a bridge that it didn't join.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change bd76a11670 made all DSA drivers
depend on NET_DSA rather than selecting them. However, as the only way
to select this option was to actually select a driver, it made DSA
impossible to enable at all.
This patch adds an explicit entry which the user will have to enable
prior selecting a driver.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This would fix randconfig compile error:
net/built-in.o: In function `netdev_switch_fib_ipv4_abort':
(.text+0xf7811): undefined reference to `fib_flush_external'
Also it fixes following warnings:
warning: (NET_DSA) selects NET_SWITCHDEV which has unmet direct dependencies (NET && INET)
warning: (NET_DSA_MV88E6060 && NET_DSA_MV88E6131 && NET_DSA_MV88E6123_61_65 && NET_DSA_MV88E6171 && NET_DSA_MV88E6352 && NET_DSA_BCM_SF2) selects NET_DSA which has unmet direct dependencies (NET && HAVE_NET_DSA && NET_SWITCHDEV)
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move swdev wrappers over to new swdev ops (from previous ndo ops). No
functional changes to the implementation.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
rocker: move to new swdev ops
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
dsa: move to new swdev ops
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit cd28a1a9ba ("net: dsa: fully divert PHY reads/writes if
requested") introduced a check for particular PHYs that need to be
accessed using the slave MII bus created by DSA, but this check was too
inclusive. This would prevent fixed PHYs from being successfully
registered because those should not go through the slave MII bus created
by DSA.
Make sure we check that the PHY is not a fixed PHY to prevent that from
happening.
Fixes: cd28a1a9ba ("net: dsa: fully divert PHY reads/writes if requested")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case a PHY is found via Device Tree, and is also flagged by the
switch driver as needing indirect reads/writes using the switch driver
implemented MDIO bus, make sure that we bind this PHY to the slave MII
bus in order for this to happen.
Without this, we would succeed in having the PHY driver probe()'s
function to use slave MII bus read/write functions, because this is done
during dsa_slave_mii_init(), but past that point, the PHY driver would
not go through these diverted reads and writes.
Fixes: 0d8bcdd383 ("net: dsa: allow for more complex PHY setups")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for dealing with indirect reads and writes towards
certain PHY devices, move the code which deals with binding the PHY
device to the slave MII bus created by DSA to its own function:
dsa_slave_phy_connect().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using of_find_device_by_node() restricts the search to platform_device that
match the specified device_node pointer. This is not even remotely true for
network devices backed by a pci_device for instance.
of_find_net_device_by_node() allows us to do a more thorough lookup to find the
struct net_device corresponding to a particular device_node pointer.
For symetry with the non-OF code path, we hold the net_device pointer in
dsa_probe() just like what dev_to_net_dev() does when we call this
function.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the core logic that setups a 'struct dsa_switch_tree' and
removes it, update dsa_probe() and dsa_remove() to use the two helper
functions. This will be useful to allow for other callers to setup
this structure differently.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support the new DSA device driver model, a dsa_switch should
be able to advertise the type of tagging protocol supported by the
underlying switch device. This also removes constraints on how tagging
can be stacked to each other.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the part of dsa_switch_setup() which is responsible for allocating
and initializing a 'struct dsa_switch' and the part which is doing a
given switch device setup and slave network device creation.
This is a preliminary change to allow a separate caller of
dsa_switch_setup_one() which may have externally initialized the
dsa_switch structure, outside of dsa_switch_setup().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing a different model to register DSA switches,
update dsa_of_probe() and dsa_probe() to return -EPROBE_DEFER where
appropriate.
Failure to find a phandle or Device Tree property is still fatal, but
looking up the internal device structure associated with a Device Tree
node is something that might need to be delayed based on driver probe
ordering.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing a different mechanism to register DSA switch
devices and driver, update dsa_of_probe and dsa_of_remove to take a
struct device pointer since neither of these two functions uses the
struct platform_device pointer.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid race conditions when using the ds->ports[] array,
we need to check if the accessed port has been initialized.
Introduce and use helper function dsa_is_port_initialized
for that purpose and use it where needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support bridging offloads in DSA switch drivers, select
NET_SWITCHDEV to get access to the port_stp_update and parent_get_id
NDOs that we are required to implement.
To facilitate the integratation at the DSA driver level, we implement 3
types of operations:
- port_join_bridge
- port_leave_bridge
- port_stp_update
DSA will resolve which switch ports that are currently bridge port
members as some Switch hardware/drivers need to know about that to limit
the register programming to just the relevant registers (especially for
slow MDIO buses).
We also take care of setting the correct STP state when slave network
devices are brought up/down while being bridge members.
Finally, when a port is leaving the bridge, we make sure we set in
BR_STATE_FORWARDING state, otherwise the bridge layer would leave it
disabled as a result of having left the bridge.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A network device notifier can be called for one or more of the created
slave devices before all slave devices have been registered. This can
result in a mismatch between ds->phys_port_mask and the registered devices
by the time the call is made, and it can result in a slave device being
added to a bridge before its entry in ds->ports[] has been initialized.
Rework the initialization code to initialize entries in ds->ports[] in
dsa_slave_create. With this change, dsa_slave_create no longer needs
to return slave_dev but can return an error code instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the phy interface mode is not found in devicetree, or if devicetree
is not configured, of_get_phy_mode returns -ENODEV. The current code
sets the phy interface mode to the return value from of_get_phy_mode
without checking if it is valid.
This invalid phy interface mode is passed as parameter to of_phy_connect
or to phy_connect_direct. This sets the phy interface mode to the invalid
value, which in turn causes problems for any code using phydev->interface.
Fixes: b31f65fb43 ("net: dsa: slave: Fix autoneg for phys on switch MDIO bus")
Fixes: 0d8bcdd383 ("net: dsa: allow for more complex PHY setups")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_slave_phy_setup() finds the phy for the port via device tree and
using of_phy_connect(), or it uses the fall back of taking a phy from
the switch internal mdio bus and calling phy_connect_direct(). Either
way, if a phy is found, phy_attach_direct() is called to attach the
phy to the slave device.
In dsa_slave_create(), a second call to phy_attach() is made. This
results in the warning "PHY already attached". Remove this second,
redundant attaching of the phy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of connected switches was sourced from the number of
children to the DSA node, change it to the number of available
children, skipping any disabled switches.
Fixes: 5e95329b70 ("dsa: add device tree bindings to register DSA switches")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When registering a mdio bus, Linux assumes than every port has a PHY and tries
to scan it. If a switch port has no PHY registered, DSA will fail to register
the slave MII bus. To fix this, set the slave MII bus PHY mask to the switch
PHYs mask.
As an example, if we use a Marvell MV88E6352 (which is a 7-port switch with no
registered PHYs for port 5 and port 6), with the following declared names:
static struct dsa_chip_data switch_cdata = {
[...]
.port_names[0] = "sw0",
.port_names[1] = "sw1",
.port_names[2] = "sw2",
.port_names[3] = "sw3",
.port_names[4] = "sw4",
.port_names[5] = "cpu",
};
DSA will fail to create the switch instance. With the PHY mask set for the
slave MII bus, only the PHY for ports 0-4 will be scanned and the instance will
be successfully created.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
