This adds code to make it possible to use the cfg80211
connect() API with wireless extensions, and because the
previous patch added emulation of that API with auth()
and assoc(), by extension also supports wext on that.
At the same time, removes code from mac80211 for wext,
but doesn't yet clean up mac80211's mlme code more.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds code to cfg80211 so that drivers (mac80211 right
now) that don't implement connect but rather auth/assoc can
still be used with the nl80211 connect command. This will
also be necessary for the wext compat code.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces the cfg80211 connect/disconnect API.
The goal here is to run the AUTH and ASSOC steps in one call.
This is needed for some fullmac cards that run both steps
directly from the target, after the host driver sends a
connect command.
Additionally, all the new crypto parameters for connect()
are now also valid for associate() -- although associate
requires the IEs to be used, the information can be useful
for drivers and should be given.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We'll need these values for some drivers using connect API
and for wext compat code, so let's define them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This introduces a new NL80211_CMD_TESTMODE for testing
and calibration use with nl80211. There's no multiplexing
like like iwpriv had, and the command is not available by
default, it needs to be explicitly enabled in Kconfig and
shouldn't be enabled in most kernels.
The command requires a wiphy index or interface index to
identify the device to operate on, and the new TESTDATA
attribute. There also is API for sending replies to the
command, and testmode multicast messages (on a testmode
multicast group).
I've also updated mac80211 to be able to pass through the
command to the driver, since it itself doesn't implement
the testmode command.
Additionally, to give people an idea of how to use the
command, I've added a little code to hwsim that makes use
of the new command to set the powersave mode, this is
currently done via debugfs and should remain there, and
the testmode command only serves as an example of how to
use this best -- with nested netlink attributes in the
TESTDATA attribute. A hwsim testmode tool can be found at
http://git.sipsolutions.net/hwsim.git/. This tool is BSD
licensed so people can easily use it as a basis for their
own internal fabrication and validation tools.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is never changed by the function, so can be marked const.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This variable isn't necessary -- the wext code keeps
track of the BSSID itself, and otherwise we have
current_bss.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcoding GFP_ATOMIC everywhere, add a
new function parameter that gets the flags from the
caller. Obviously then I need to update all callers
(all of them in mac80211), and it turns out that now
it's ok to use GFP_KERNEL in almost all places.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Within mac80211, we often need to copy the rx status into
skb->cb. This is wasteful, as drivers could be building it
in there to start with. This patch changes the API so that
drivers are expected to pass the RX status in skb->cb, now
accessible as IEEE80211_SKB_RXCB(skb). It also updates all
drivers to pass the rx status in there, but only by making
them memcpy() it into place before the call to the receive
function (ieee80211_rx(_irqsafe)). Each driver can now be
optimised on its own schedule.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow minidriver to know that netdev has stopped. This is to let
wireless turn off radio when usbnet dev is stopped.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If there was a reason I'm passing the ifidx I cannot
remember it any more and don't see one now, so let's
just pass the pointer itself.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding smp_mb__after_lock define to be used as a smp_mb call after
a lock.
Making it nop for x86, since {read|write|spin}_lock() on x86 are
full memory barriers.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding memory barrier after the poll_wait function, paired with
receive callbacks. Adding fuctions sock_poll_wait and sk_has_sleeper
to wrap the memory barrier.
Without the memory barrier, following race can happen.
The race fires, when following code paths meet, and the tp->rcv_nxt
and __add_wait_queue updates stay in CPU caches.
CPU1 CPU2
sys_select receive packet
... ...
__add_wait_queue update tp->rcv_nxt
... ...
tp->rcv_nxt check sock_def_readable
... {
schedule ...
if (sk->sk_sleep && waitqueue_active(sk->sk_sleep))
wake_up_interruptible(sk->sk_sleep)
...
}
If there was no cache the code would work ok, since the wait_queue and
rcv_nxt are opposit to each other.
Meaning that once tp->rcv_nxt is updated by CPU2, the CPU1 either already
passed the tp->rcv_nxt check and sleeps, or will get the new value for
tp->rcv_nxt and will return with new data mask.
In both cases the process (CPU1) is being added to the wait queue, so the
waitqueue_active (CPU2) call cannot miss and will wake up CPU1.
The bad case is when the __add_wait_queue changes done by CPU1 stay in its
cache, and so does the tp->rcv_nxt update on CPU2 side. The CPU1 will then
endup calling schedule and sleep forever if there are no more data on the
socket.
Calls to poll_wait in following modules were ommited:
net/bluetooth/af_bluetooth.c
net/irda/af_irda.c
net/irda/irnet/irnet_ppp.c
net/mac80211/rc80211_pid_debugfs.c
net/phonet/socket.c
net/rds/af_rds.c
net/rfkill/core.c
net/sunrpc/cache.c
net/sunrpc/rpc_pipe.c
net/tipc/socket.c
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix the following 'make includecheck' warning:
include/linux/rfkill.h: linux/types.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case if kernel was compiled without ebtables support
there is no need to keep ebt_table pointers in netns_xt
structure.
Make it config dependent.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows a TIPC application to determine the number of messages
currently waiting in a socket's receive queue (TIPC_SOCK_RECVQ_DEPTH) or
in all TIPC socket receive queues (TIPC_NODE_RECVQ_DEPTH).
Signed-off-by: Oscar Medina <oscar.medina@motorola.com>
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes an unused member (seq) scm_cookie; besides initialized
to 0 in the header file, it is not used.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
almost no users in the tree; and the few that use them treat them
like NET_RX_DROP.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
kbuild: finally remove the obsolete variable $TOPDIR
gitignore: ignore scripts/ihex2fw
Kbuild: Disable the -Wformat-security gcc flag
gitignore: ignore gcov output files
kbuild: deb-pkg ship changelog
Add new __init_task_data macro to be used in arch init_task.c files.
asm-generic/vmlinux.lds.h: shuffle INIT_TASK* macro names in vmlinux.lds.h
Add new macros for page-aligned data and bss sections.
asm-generic/vmlinux.lds.h: Fix up RW_DATA_SECTION definition.
This patch adds ETH_P_1588 protocol ID define.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: invalidation reverse calls
fuse: allow umask processing in userspace
fuse: fix bad return value in fuse_file_poll()
fuse: fix return value of fuse_dev_write()
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cfq-iosched: remove redundant check for NULL cfqq in cfq_set_request()
blocK: Restore barrier support for md and probably other virtual devices.
block: get rid of queue-private command filter
block: Create bip slabs with embedded integrity vectors
cfq-iosched: get rid of the need for __GFP_NOFAIL in cfq_find_alloc_queue()
cfq-iosched: move cfqq initialization out of cfq_find_alloc_queue()
Trivial typo fixes in Documentation/block/data-integrity.txt.
The initial patches to support this through sysfs export were broken
and have been if 0'ed out in any release. So lets just kill the code
and reclaim some space in struct request_queue, if anyone would later
like to fixup the sysfs bits, the git history can easily restore
the removed bits.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch restores stacking ability to the block layer integrity
infrastructure by creating a set of dedicated bip slabs. Each bip slab
has an embedded bio_vec array at the end. This cuts down on memory
allocations and also simplifies the code compared to the original bvec
version. Only the largest bip slab is backed by a mempool. The pool is
contained in the bio_set so stacking drivers can ensure forward
progress.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@carl.(none)>
Now that nothing uses the private stats structure we can remove it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (47 commits)
perf report: Add --symbols parameter
perf report: Add --comms parameter
perf report: Add --dsos parameter
perf_counter tools: Adjust only prelinked symbol's addresses
perf_counter: Provide a way to enable counters on exec
perf_counter tools: Reduce perf stat measurement overhead/skew
perf stat: Use percentages for scaling output
perf_counter, x86: Update x86_pmu after WARN()
perf stat: Micro-optimize the code: memcpy is only required if no event is selected and !null_run
perf stat: Improve output
perf stat: Fix multi-run stats
perf stat: Add -n/--null option to run without counters
perf_counter tools: Remove dead code
perf_counter: Complete counter swap
perf report: Print sorted callchains per histogram entries
perf_counter tools: Prepare a small callchain framework
perf record: Fix unhandled io return value
perf_counter tools: Add alias for 'l1d' and 'l1i'
perf-report: Add bare minimum PERF_EVENT_READ parsing
perf-report: Add modes for inherited stats and no-samples
...
Add a mutex to avoid a circular locking problem between the mm layer
semaphore and fbdev ioctl mutex through the fb_mmap() call.
Also, add mutex to all places where smem_start and smem_len fields change
so the mutex inside the fb_mmap() is actually used. Changing of these
fields before calling the framebuffer_register() are not mutexed.
This is 2.6.31 material. It removes one lockdep (fb_mmap() and
register_framebuffer()) but there is still another one (fb_release() and
register_framebuffer()). It also cleans up handling of the smem_start and
smem_len fields used by mutexed section of the fb_mmap().
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new spi_master.flags word listing constraints relevant to that
controller. Define the first constraint bit: a half duplex restriction.
Include that constraint in the OMAP1 MicroWire controller driver.
Have the mmc_spi host be the first customer of this flag. Its coding
relies heavily on full duplex transfers, so it must fail when the
underlying controller driver won't perform them.
(The spi_write_then_read routine could use it too: use the
temporarily-withdrawn full-duplex speedup unless this flag is set, in
which case the existing code applies. Similarly, any spi_master
implementing only SPI_3WIRE should set the flag.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add two new spi_device.mode bits to accomodate more protocol options, and
pass them through to usermode drivers:
* SPI_NO_CS ... a second 3-wire variant, where the chipselect
line is removed instead of a data line; transfers are still
full duplex.
This obviously has STRONG protocol implications since the
chipselect transitions can't be used to synchronize state
transitions with the SPI master.
* SPI_READY ... defines open drain signal that's pulled low
to pause the clock. This defines a 5-wire variant (normal
4-wire SPI plus READY) and two 4-wire variants (READY plus
each of the 3-wire flavors).
Such hardware flow control can be a big win. There are ADC
converters and flash chips that expose READY signals, but not
many host controllers support it today.
The spi_bitbang code should be changed to use SPI_NO_CS instead of its
current nonportable hack. That's a mode most hardware can easily support
(unlike SPI_READY).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: "Paulraj, Sandeep" <s-paulraj@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With ELF, at generating coredump, some more headers other than used
vmas are added.
When max_map_count == 65536, a core generated by following kinds of
code can be unreadable because the number of ELF's program header is
written in 16bit in Ehdr (please see elf.h) and the number overflows.
==
... = mmap(); (munmap, mprotect, etc...)
if (failed)
abort();
==
This can happen in mmap/munmap/mprotect/etc...which calls split_vma().
I think 65536 is not safe as _default_ and reduce it to 65530 is good
for avoiding unexpected corrupted core.
Anyway, max_map_count can be enlarged by sysctl if a user is brave..
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Jakub Jelinek <jakub@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alpha percpu access requires custom SHIFT_PERCPU_PTR() definition for
modules to work around addressing range limitation. This is done via
generating inline assembly using C preprocessing which forces the
assembler to generate external reference. This happens behind the
compiler's back and makes the compiler think that static percpu variables
in modules are unused.
This used to be worked around by using __unused attribute for percpu
variables which prevent the compiler from omitting the variable; however,
recent declare/definition attribute unification change broke this as
__used can't be used for declaration. Also, in the process,
PER_CPU_ATTRIBUTES definition in alpha percpu.h got broken.
This patch adds PER_CPU_DEF_ATTRIBUTES which is only used for definitions
and make alpha use it to add __used for percpu variables in modules. This
also fixes the PER_CPU_ATTRIBUTES double definition bug.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: maximilian attems <max@stro.at>
Acked-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ctors section for each object file is eight byte aligned (on 64 bit).
However the __ctors_start symbol starts at an arbitrary address dependent
on the size of the previous sections.
Therefore the linker may add some zeroes after __ctors_start to make sure
the ctors contents are properly aligned. However the extra zeroes at the
beginning aren't expected by the code. When walking the functions
pointers contained in there and extra zeroes are added this may result in
random jumps. So make sure that the __ctors_start symbol is always
aligned as well.
Fixes this crash on an allyesconfig on s390:
[ 0.582482] Kernel BUG at 0000000000000012 [verbose debug info unavailable]
[ 0.582489] illegal operation: 0001 [#1] SMP DEBUG_PAGEALLOC
[ 0.582496] Modules linked in:
[ 0.582501] CPU: 0 Tainted: G W 2.6.31-rc1-dirty #273
[ 0.582506] Process swapper (pid: 1, task: 000000003f218000, ksp: 000000003f2238e8)
[ 0.582510] Krnl PSW : 0704200180000000 0000000000000012 (0x12)
[ 0.582518] R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:0 CC:2 PM:0 EA:3
[ 0.582524] Krnl GPRS: 0000000000036727 0000000000000010 0000000000000001 0000000000000001
[ 0.582529] 00000000001dfefa 0000000000000000 0000000000000000 0000000000000040
[ 0.582534] 0000000001fff0f0 0000000001790628 0000000002296048 0000000002296048
[ 0.582540] 00000000020c438e 0000000001786000 0000000002014a66 000000003f223e60
[ 0.582553] Krnl Code:>0000000000000012: 0000 unknown
[ 0.582559] 0000000000000014: 0000 unknown
[ 0.582564] 0000000000000016: 0000 unknown
[ 0.582570] 0000000000000018: 0000 unknown
[ 0.582575] 000000000000001a: 0000 unknown
[ 0.582580] 000000000000001c: 0000 unknown
[ 0.582585] 000000000000001e: 0000 unknown
[ 0.582591] 0000000000000020: 0000 unknown
[ 0.582596] Call Trace:
[ 0.582599] ([<0000000002014a46>] kernel_init+0x622/0x7a0)
[ 0.582607] [<0000000000113e22>] kernel_thread_starter+0x6/0xc
[ 0.582615] [<0000000000113e1c>] kernel_thread_starter+0x0/0xc
[ 0.582621] INFO: lockdep is turned off.
[ 0.582624] Last Breaking-Event-Address:
[ 0.582627] [<0000000002014a64>] kernel_init+0x640/0x7a0
Cc: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the eventfd interface to de-couple the eventfd memory context, from
the file pointer instance.
Without such change, there is no clean way to racely free handle the
POLLHUP event sent when the last instance of the file* goes away. Also,
now the internal eventfd APIs are using the eventfd context instead of the
file*.
This patch is required by KVM's IRQfd code, which is still under
development.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Gregory Haskins <ghaskins@novell.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Avi Kivity <avi@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add notification messages that allow the filesystem to invalidate VFS
caches.
Two notifications are added:
1) inode invalidation
- invalidate cached attributes
- invalidate a range of pages in the page cache (this is optional)
2) dentry invalidation
- try to invalidate a subtree in the dentry cache
Care must be taken while accessing the 'struct super_block' for the
mount, as it can go away while an invalidation is in progress. To
prevent this, introduce a rw-semaphore, that is taken for read during
the invalidation and taken for write in the ->kill_sb callback.
Cc: Csaba Henk <csaba@gluster.com>
Cc: Anand Avati <avati@zresearch.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
This provides a way to mark a counter to be enabled on the next
exec. This is useful for measuring the total activity of a
program without including overhead from the process that
launches it.
This also changes the perf stat command to use this new
facility.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <19017.43927.838745.689203@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-2.6:
ide: memory overrun in ide_get_identity_ioctl() on big endian machines using ioctl HDIO_OBSOLETE_IDENTITY
ide: fix resume for CONFIG_BLK_DEV_IDEACPI=y
ide-cd: handle fragmented packet commands gracefully
ide: always kill the whole request on error
ide: fix ide_kill_rq() for special ide-{floppy,tape} driver requests
commit 2f0d0fd2a6 ("ide-acpi: cleanup
do_drive_get_GTF()") didn't account for the lack of hwif->acpidata
check in generic_ide_suspend() [ indirect user of do_drive_get_GTF()
through ide_acpi_exec_tfs() ] resulting in broken resume when ACPI
support is enabled but ACPI data is unavailable.
Fix it by adding ide_port_acpi() helper for checking if port needs
ACPI handling and cleaning generic_ide_{suspend,resume}() to use it
instead of hiding hwif->acpidata and ide_noacpi checks in IDE ACPI
helpers (this should help in preventing similar bugs in the future).
While at it:
- kill superfluous debugging printks in ide_acpi_{get,push}_timing()
Reported-and-tested-by: Etienne Basset <etienne.basset@numericable.fr>
Also-reported-and-tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new fsnotify infrastructure (starting at 90586523) causes an oops in
spufs, where we populate a directory with files before instantiating the
directory itself. The new changes seem to have introduced an assumption
that a dentry's parent will be positive when instantiating.
This change makes it once again possible to d_instantiate a dentry
with a negative parent, and brings __fsnotify_d_instantiate() into
line with inotify_d_instantiate(), which already has this NULL check.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Eric Paris <eparis@redhat.com>
As reported by Philip, the UNTRACKED state bit does not fit within
the 8-bit state_mask member. Enlarge state_mask and give status_mask
a few more bits too.
Reported-by: Philip Craig <philipc@snapgear.com>
References: http://markmail.org/thread/b7eg6aovfh4agyz7
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
fix the following 'make headers_check' warnings:
usr/include/linux/netfilter/xt_osf.h:40: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
When NAT helpers change the TCP packet size, the highest seen sequence
number needs to be corrected. This is currently only done upwards, when
the packet size is reduced the sequence number is unchanged. This causes
TCP conntrack to falsely detect unacknowledged data and decrease the
timeout.
Fix by updating the highest seen sequence number in both directions after
packet mangling.
Tested-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
