The current 'mount_ubifs()' implementation does not initialize the LPT until the
the master node is marked dirty. Move the LPT initialization to before marking
the master node dirty. This is a preparation for the next patch which will move
the free-space-fixup check to before marking the master node dirty, because we
have to fix-up the free space before doing any writes.
Artem: massaged the patch and commit message.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Matthew L. Creech <mlcreech@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The current free space fixup can result in some writing to the UBI volume
when the space_fixup flag is set.
To catch instances where UBIFS is writing to the NAND while the space_fixup
flag is set, add an assert to ubifs_write_node().
Artem: tweaked the patch, added similar assertion to the write buffer
write path.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Matthew L. Creech <mlcreech@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
UBIFS maintains per-filesystem and global clean znode counters
('c->clean_zn_cnt' and 'ubifs_clean_zn_cnt'). It is important to maintain
correct values there since the shrinker relies on 'ubifs_clean_zn_cnt'.
However, in case of failures during commit the counters were corrupted. E.g.,
if a failure happens in the middle of 'write_index()', then some nodes in the
commit list ('c->cnext') are marked as clean, and some are marked as dirty. And
the 'ubifs_destroy_tnc_subtree()' frees does not retrun correct count, and we
end up with non-zero 'c->clean_zn_cnt' when unmounting. This means that if we
have 2 file-sytem and one of them fails, and we unmount it,
'ubifs_clean_zn_cnt' stays incorrect and confuses the shrinker.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
UBIFS leaks memory on error path in 'ubifs_jnl_update()' in case of write
failure because it forgets to free the 'struct ubifs_dent_node *dent' object.
Although the object is small, the alignment can make it large - e.g., 2KiB
if the min. I/O unit is 2KiB.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: stable@kernel.org
Sometimes VM asks the shrinker to return amount of objects it can shrink,
and we return the ubifs_clean_zn_cnt in that case. However, it is possible
that this counter is negative for a short period of time, due to the way
UBIFS TNC code updates it. And I can observe the following warnings sometimes:
shrink_slab: ubifs_shrinker+0x0/0x2b7 [ubifs] negative objects to delete nr=-8541616642706119788
This patch makes sure UBIFS never returns negative count of objects.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: stable@kernel.org
The jump to 4f will cause the NUL padding loop to run at least one time,
so if string length is zero just jump to the end. Otherwise we wrongly
write one NUL byte when size==0.
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Mandatory arguments need to be present in the argument name list, as
well as optional arguments, otherwise python barfs:
# ./python/twatch.py
Traceback (most recent call last):
File "./python/twatch.py", line 41, in <module>
main()
File "./python/twatch.py", line 32, in main
event = evlist.read_on_cpu(cpu)
RuntimeError: more argument specifiers than keyword list entries
Hence, add cpu to the name list.
Cc: David Ahern <daahern@cisco.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
Link: http://lkml.kernel.org/r/1301588863-20210-1-git-send-email-fweisbec@gmail.com
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Fixes two more cases where the python binding would not load:
. Not finding die(), which it shouldn't anyway, not good to just stop the
world because some particular perf.data file is invalid, just propagate
the error to the caller.
. Not finding perf_sample_size: fix it by moving it from event.c to evsel,
where it belongs, as most cases are moving to operate on an evsel object.o
One of the fixed problems:
[root@emilia ~]# python
>>> import perf
Traceback (most recent call last):
File "<stdin>", line 1, in <module>
ImportError: /home/acme/git/build/perf/python/perf.so: undefined symbol: perf_sample_size
>>>
[root@emilia ~]#
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-1hkj7b2cvgbfnoizsekjb6c9@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
We were using pr_debug to tell the user about not being able to parse a sample
where we should really use the python way of reporting errors: exceptions.
Fixes this problem:
[root@emilia ~]# python
>>> import perf
Traceback (most recent call last):
File "<stdin>", line 1, in <module>
ImportError: /home/acme/git/build/perf/python/perf.so: undefined symbol: eprintf
>>>
[root@emilia ~]
As we want to keep the objects linked in the python binding (and in the future
in a shared library) minimal.
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-m9dba9kaluas0kq8r58z191c@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
So far we avoided having to link debug.o in the python binding, keep it
that way by not using ui__warning() in evlist.c.
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-4wtew8hd3g7ejnlehtspys2t@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
There is an optimization which does not update the timer if the timer
was pending and the expiration time was unchanged.
Since commit 3bbb9ec9 ("timers: Introduce the concept of timer slack
for legacy timers") this optimization is no longer applied for timers
where the expiration time got extended due to the slack value. So we
need to check again after the expiration time might have been updated.
[ tglx: Made it a single check by applying slack first and sorting
out the slack = 0 value (all timeouts < 256 jiffies) early ]
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Link: http://lkml.kernel.org/r/20110521105828.GA29442@Chamillionaire.breakpoint.cc
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When irq_alloc_descs() is called with no base IRQ specified then it will
search for a range of IRQs starting from a specified base address. In the
case where an IRQ is specified it still does this search in order to ensure
that none of the requested range is already allocated and it still uses the
from parameter to specify the base for the search. This means that in the
case where a base is specified but from is zero (which is reasonable as
any IRQ number is in the range specified by a zero from) the function will
get confused and try to allocate the first suitably sized block of free IRQs
it finds.
Instead use a specified IRQ as the base address for the search, and insist
that any from that is specified can support that IRQ.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Link: http://lkml.kernel.org/r/1307037313-15733-1-git-send-email-broonie@opensource.wolfsonmicro.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The genirq changes are initializing descriptors for sparse IRQs quite
differently from how non-sparse (stacked?) IRQs are initialized, with
the effect that on my platform all IRQs are default-disabled on sparse
IRQs and default-enabled if non-sparse IRQs are used, crashing some
GPIO driver.
Fix this by refactoring the non-sparse IRQs to use the same descriptor
init function as the sparse IRQs.
Signed-off: Linus Walleij <linus.walleij@linaro.org>
Link: http://lkml.kernel.org/r/1306858479-16622-1-git-send-email-linus.walleij@stericsson.com
Cc: stable@kernel.org # 2.6.39
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The detection of spurios interrupts is currently limited to first level
handler. In force-threaded mode we never notice if the threaded irq does
not feel responsible.
This patch catches the return value of the threaded handler and forwards
it to the spurious detector. If the primary handler returns only
IRQ_WAKE_THREAD then the spourious detector ignores it because it gets
called again from the threaded handler.
[ tglx: Report the erroneous return value early and bail out ]
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Link: http://lkml.kernel.org/r/1306824972-27067-2-git-send-email-sebastian@breakpoint.cc
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In forced threaded mode (or with an explicit threaded handler) we only
see the primary handler, but not the threaded handler.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Link: http://lkml.kernel.org/r/1306824972-27067-1-git-send-email-sebastian@breakpoint.cc
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
For UP it's stupid to request an initialized cpumask for the clock
event devices. Though we need the mask set even on UP to avoid a
horrible ifdeffery especially in the broadcast code.
For SMP we can at least try to survive with a warning and set the
cpumask of the cpu we're running on. That gives a decent chance to
bring the machine up and retrieve the debug info.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Walleij <linus.walleij@linaro.org
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Stephen Boyd <sboyd@codeaurora.org>
In the original code if auto detect failed and tea575x_tuner == 4
then we copy bogus information to chip->tea.card. I've changed the
autodetect code to cleanup and return -ENODEV on error instead.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In ad198x_power_eapd(), wrong pin NIDs are used for controlling EAPD for
HP and Front outputs of AD1988/AD1989. These are actually same with the
ones for AD1984 & co, port-A is 0x11 and port-D 0x12.
Reported-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This function attempts to free one fragment beyond the number of
fragments that were actually mapped. This patch brings back the limit
to the correct spot.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Fresco Logic hosts, including those found in the AUAU N533V laptop,
advertise MSI, but fail to actually generate MSI interrupts. Add a new
xHCI quirk to skip MSI enabling for the Fresco Logic host controllers.
Fresco Logic confirms that all chips with PCI vendor ID 0x1b73 and device
ID 0x1000, regardless of PCI revision ID, do not support MSI.
This should be backported to stable kernels as far back as 2.6.36, which
was the first kernel to support MSI on xHCI hosts.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Sergey Galanov <sergey.e.galanov@gmail.com>
Cc: stable@kernel.org
xHCI controllers respond to a Reset Device command when the Slot is in the
Enabled/Disabled state by returning an error. This is fine on other host
controllers, but the Etron xHCI host controller returns a vendor-specific
error code that the xHCI driver doesn't understand. The xHCI driver then
gives up on device enumeration.
Instead of issuing a command that will fail, just return. This fixes the
issue with the xhci driver not working on ASRock P67 Pro/Extreme boards.
This should be backported to stable kernels as far back as 2.6.34.
Signed-off-by: Maarten Lankhorst <m.b.lankhorst@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
This needs to be added to the stable trees back to 2.6.34 to support an
upcoming bug fix.
Signed-off-by: Maarten Lankhorst <m.b.lankhorst@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Commit 834cb0fc47 "xhci: Fix memory leak
bug when dropping endpoints" added a small endian bug. This patch fixes
xhci_check_bandwidth() to read add/drop_flags LE.
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Because there is a possibility that skb is kfree_skb()ed and zero cleared
after ndo_start_xmit, we should not see the contents of skb like skb->len and
skb->dev->name after ndo_start_xmit. But trace_net_dev_xmit does that
and causes panic by NULL pointer dereference.
This patch fixes trace_net_dev_xmit not to see the contents of skb directly.
If you want to reproduce this panic,
1. Get tracepoint of net_dev_xmit on
2. Create 2 guests on KVM
2. Make 2 guests use virtio_net
4. Execute netperf from one to another for a long time as a network burden
5. host will panic(It takes about 30 minutes)
Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the error paths in
sound/usb/6fire/firmware.c::usb6fire_fw_ezusb_upload() neglects to free
the memory allocated for the firmware before returning, thus leaking the
memory.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
By ignoring the unset values of the minconfig in deciding
what to test in the config_bisect can cause the problem
config from being tested too.
Just do not test the configs that are set in the minconfig.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The command that is called that reboots the kernel may fail
but the return code is not passed back to the ktest.pl script.
This is because a ';' is used between the two commands and
if the second command fails, only the first command's return
code is returned. Using a '&&' between the two commands fixes
this.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Because in perl the array size returned by $#arr, is the last
index and not the actually size of the array, we end the config
bisect early, thinking there is only one config left when there
are in fact two. Thus the result has a 50% chance of picking
the correct config that caused the problem.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
list_entry() and hlist_entry() are both simply aliases for
container_of(), but since io_context.cic_list.first is an hlist_node one
should at least use the correct alias.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
queue_fail can only be reached if cic is NULL, so its check for cic must
be bogus.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
In certain circumstances, we can get an oops from a torn down device.
Most notably this is from CD roms trying to call scsi_ioctl. The root
cause of the problem is the fact that after scsi_remove_device() has
been called, the queue is fully torn down. This is actually wrong
since the queue can be used until the sdev release function is called.
Therefore, we add an extra reference to the queue which is released in
sdev->release, so the queue always exists.
Reported-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Both were buggy: bind would happily scribble over a real graphics
device and unbind wouldn't destroy the framebuffer. Hotplugging
efifb makes no sense anyway, so just disable it.
As an added benefit, we save some runtime memory.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Running fbcon on an uncached framebuffer is remarkably slow. So try
to enable write combining in efifb.
Without this patch, it takes 5.8 seconds from efifb probe to i915
probe (default options; no plymouth or quiet mode). With this patch,
it only takes 1.7 seconds. That means we wasted over 4 seconds just
writing to UC memory.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a label for error-handling code in the case where only clk_get has
succeeded. Rename the label failed to be consistent with the rest.
A simplified version of the semantic match that finds the missing clk_put
is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression e1,e2;
statement S;
@@
e1 = clk_get@p1(...);
... when != e1 = e2
when != clk_put(e1)
when any
if (...) { ... when != clk_put(e1)
when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
} else S
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Reorder the labels at the end of the function to correspond to the order in
which the resources are allocated.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression e1,e2;
statement S;
@@
e1 = clk_get@p1(...);
... when != e1 = e2
when != clk_put(e1)
when any
if (...) { ... when != clk_put(e1)
when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
} else S
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Seems this new field was missed, probably due to this driver being merged
around the time this new backlight field was being added. At any rate,
initial the type field to avoid ugly WARN() dumps.
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If there is no EDID but an LCD panel is detected, generate a CVT
mode from the panel resolution (at 60 Hz), and use this as a
default mode instead of the hardcoded 800x600x8 mode.
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The LCDC driver does no longer compile:
CC drivers/video/sh_mobile_meram.o
CC drivers/video/sh_mobile_lcdcfb.o
drivers/video/sh_mobile_lcdcfb.c: In function 'sh_mobile_lcdc_start':
drivers/video/sh_mobile_lcdcfb.c:640:4: error: 'ret' undeclared (first use in this function)
drivers/video/sh_mobile_lcdcfb.c:640:4: note: each undeclared identifier is reported only once for each function it appears in
make[2]: *** [drivers/video/sh_mobile_lcdcfb.o] Error 1
make[1]: *** [drivers/video] Error 2
make: *** [drivers] Error 2
Reported-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The failed_get label is used after the call to clk_get has succeeded, so it
should be moved up above the call to clk_put.
The failed_req labels doesn't do anything different than failed_get, so
delete it.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression e1,e2;
statement S;
@@
e1 = clk_get@p1(...);
... when != e1 = e2
when != clk_put(e1)
when any
if (...) { ... when != clk_put(e1)
when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
} else S
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
These definitions are needed to let the runtime PM subsystem turn off
DMAC clocks, when it is suspended by the driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
A recent patch has introduced a regression, where repeating a memcpy
DMA test with shdma module unloading between them skips the DMA channel
configuration. Fix this regression by always configuring the channel
during its allocation.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently the DM9000 driver requests the primary interrupt before it
resets the chip and puts it into a known good state. This means that if
the chip is asserting interrupt for some reason we can end up with a
screaming IRQ that the interrupt handler is unable to deal with. Avoid
this by only requesting the interrupt after we've reset the chip so we
know what state it's in.
This started manifesting itself on one of my boards in the past month or
so, I suspect as a result of some core infrastructure changes removing
some form of mitigation against bad behaviour here, even when things boot
it seems that the new code brings the interface up more quickly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Go to existing error handling code at the end of the function that calls
clk_put.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression e1,e2;
statement S;
@@
e1 = clk_get@p1(...);
... when != e1 = e2
when != clk_put(e1)
when any
if (...) { ... when != clk_put(e1)
when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
} else S
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, user-space cannot determine if a 0 tcp_vlan_tci
means there is no VLAN tag or the VLAN ID was zero.
Add flag to make this explicit. User-space can check for
TP_STATUS_VLAN_VALID || tp_vlan_tci > 0, which will be backwards
compatible. Older could would have just checked for tp_vlan_tci,
so it will work no worse than before.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
