We got the following use-after-free KASAN report:
BUG: KASAN: use-after-free in wiphy_resume+0x591/0x5a0 [cfg80211]
at addr ffff8803fc244090
Read of size 8 by task kworker/u16:24/2587
CPU: 6 PID: 2587 Comm: kworker/u16:24 Tainted: G B 4.9.13-debug+
Hardware name: Dell Inc. XPS 15 9550/0N7TVV, BIOS 1.2.19 12/22/2016
Workqueue: events_unbound async_run_entry_fn
ffff880425d4f9d8 ffffffffaeedb541 ffff88042b80ef00 ffff8803fc244088
ffff880425d4fa00 ffffffffae84d7a1 ffff880425d4fa98 ffff8803fc244080
ffff88042b80ef00 ffff880425d4fa88 ffffffffae84da3a ffffffffc141f7d9
Call Trace:
[<ffffffffaeedb541>] dump_stack+0x85/0xc4
[<ffffffffae84d7a1>] kasan_object_err+0x21/0x70
[<ffffffffae84da3a>] kasan_report_error+0x1fa/0x500
[<ffffffffc141f7d9>] ? cfg80211_bss_age+0x39/0xc0 [cfg80211]
[<ffffffffc141f83a>] ? cfg80211_bss_age+0x9a/0xc0 [cfg80211]
[<ffffffffae48d46d>] ? trace_hardirqs_on+0xd/0x10
[<ffffffffc13fb1c0>] ? wiphy_suspend+0xc70/0xc70 [cfg80211]
[<ffffffffae84def1>] __asan_report_load8_noabort+0x61/0x70
[<ffffffffc13fb100>] ? wiphy_suspend+0xbb0/0xc70 [cfg80211]
[<ffffffffc13fb751>] ? wiphy_resume+0x591/0x5a0 [cfg80211]
[<ffffffffc13fb751>] wiphy_resume+0x591/0x5a0 [cfg80211]
[<ffffffffc13fb1c0>] ? wiphy_suspend+0xc70/0xc70 [cfg80211]
[<ffffffffaf3b206e>] dpm_run_callback+0x6e/0x4f0
[<ffffffffaf3b31b2>] device_resume+0x1c2/0x670
[<ffffffffaf3b367d>] async_resume+0x1d/0x50
[<ffffffffae3ee84e>] async_run_entry_fn+0xfe/0x610
[<ffffffffae3d0666>] process_one_work+0x716/0x1a50
[<ffffffffae3d05c9>] ? process_one_work+0x679/0x1a50
[<ffffffffafdd7b6d>] ? _raw_spin_unlock_irq+0x3d/0x60
[<ffffffffae3cff50>] ? pwq_dec_nr_in_flight+0x2b0/0x2b0
[<ffffffffae3d1a80>] worker_thread+0xe0/0x1460
[<ffffffffae3d19a0>] ? process_one_work+0x1a50/0x1a50
[<ffffffffae3e54c2>] kthread+0x222/0x2e0
[<ffffffffae3e52a0>] ? kthread_park+0x80/0x80
[<ffffffffae3e52a0>] ? kthread_park+0x80/0x80
[<ffffffffae3e52a0>] ? kthread_park+0x80/0x80
[<ffffffffafdd86aa>] ret_from_fork+0x2a/0x40
Object at ffff8803fc244088, in cache kmalloc-1024 size: 1024
Allocated:
PID = 71
save_stack_trace+0x1b/0x20
save_stack+0x46/0xd0
kasan_kmalloc+0xad/0xe0
kasan_slab_alloc+0x12/0x20
__kmalloc_track_caller+0x134/0x360
kmemdup+0x20/0x50
brcmf_cfg80211_attach+0x10b/0x3a90 [brcmfmac]
brcmf_bus_start+0x19a/0x9a0 [brcmfmac]
brcmf_pcie_setup+0x1f1a/0x3680 [brcmfmac]
brcmf_fw_request_nvram_done+0x44c/0x11b0 [brcmfmac]
request_firmware_work_func+0x135/0x280
process_one_work+0x716/0x1a50
worker_thread+0xe0/0x1460
kthread+0x222/0x2e0
ret_from_fork+0x2a/0x40
Freed:
PID = 2568
save_stack_trace+0x1b/0x20
save_stack+0x46/0xd0
kasan_slab_free+0x71/0xb0
kfree+0xe8/0x2e0
brcmf_cfg80211_detach+0x62/0xf0 [brcmfmac]
brcmf_detach+0x14a/0x2b0 [brcmfmac]
brcmf_pcie_remove+0x140/0x5d0 [brcmfmac]
brcmf_pcie_pm_leave_D3+0x198/0x2e0 [brcmfmac]
pci_pm_resume+0x186/0x220
dpm_run_callback+0x6e/0x4f0
device_resume+0x1c2/0x670
async_resume+0x1d/0x50
async_run_entry_fn+0xfe/0x610
process_one_work+0x716/0x1a50
worker_thread+0xe0/0x1460
kthread+0x222/0x2e0
ret_from_fork+0x2a/0x40
Memory state around the buggy address:
ffff8803fc243f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8803fc244000: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff8803fc244080: fc fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8803fc244100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8803fc244180: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
What is happening is that brcmf_pcie_resume() detects a device that
is no longer responsive and it decides to unbind resulting in a
wiphy_unregister() and wiphy_free() call. Now the wiphy instance
remains allocated, because PM needs to call wiphy_resume() for it.
However, brcmfmac already does a kfree() for the struct
cfg80211_registered_device::ops field. Change the checks in
wiphy_resume() to only access the struct cfg80211_registered_device::ops
if the wiphy instance is still registered at this time.
Cc: stable@vger.kernel.org # 4.10.x, 4.9.x
Reported-by: Daniel J Blueman <daniel@quora.org>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sowmini pointed out Dmitry's RTNL deadlock report to me, and it turns out
to be perfectly accurate - there are various error paths that miss unlock
of the RTNL.
To fix those, change the locking a bit to not be conditional in all those
nl80211_prepare_*_dump() functions, but make those require the RTNL to
start with, and fix the buggy error paths. This also let me use sparse
(by appropriately overriding the rtnl_lock/rtnl_unlock functions) to
validate the changes.
Cc: stable@vger.kernel.org
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* use shash in mac80211 crypto code where applicable
* some documentation fixes
* pass RSSI levels up in change notifications
* remove unused rfkill-regulator
* various other cleanups
-----BEGIN PGP SIGNATURE-----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=sqkq
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Some more updates:
* use shash in mac80211 crypto code where applicable
* some documentation fixes
* pass RSSI levels up in change notifications
* remove unused rfkill-regulator
* various other cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The nl80211_nan_dual_band_conf enumeration doesn't make much sense.
The default value is assigned to a bit, which makes it weird if the
default bit and other bits are set at the same time.
To improve this, get rid of NL80211_NAN_BAND_DEFAULT and add a wiphy
configuration to let the drivers define which bands are supported.
This is exposed to the userspace, which then can make a decision on
which band(s) to use. Additionally, rename all "dual_band" elements
to "bands", to make things clearer.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update the drivers to pass the RSSI level as a cfg80211_cqm_rssi_notify
parameter and pass this value to userspace in a new nl80211 attribute.
This helps both userspace and also helps in the implementation of the
multiple RSSI thresholds CQM mechanism.
Note for marvell/mwifiex I pass 0 for the RSSI value because the new
RSSI value is not available to the driver at the time of the
cfg80211_cqm_rssi_notify call, but the driver queries the new value
immediately after that, so it is actually available just a moment later
if we wanted to defer caling cfg80211_cqm_rssi_notify until that moment.
Without this, the new cfg80211 code (patch 3) will call .get_station
which will send a duplicate HostCmd_CMD_RSSI_INFO command to the hardware.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For wowlan netdetect a separate limit is defined for the number of
matchsets. Currently, this limit is ignored and the regular limit
for scheduled scan matchsets, ie. struct wiphy::max_match_sets, is
used for the net-detect case as well.
Cc: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For the benefit of drivers that rebuild IEs in firmware, parse the
IEs for HT/VHT capabilities and the respective membership selector
in the (extended) supported rates. This avoids duplicating the same
code into all drivers that need this information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Avoid assigning rdev to NULL when we already have it and getting it
again from the wiphy index, by moving this code to relevant if block.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This fixes the checkpatch.pl warnings:
* Macros should not use a trailing semicolon.
* Spaces required around that '='.
* Symbolic permissions 'S_IRUGO' are not preferred.
Signed-off-by: Dmitriy Pichugin <smokeman85@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The conflict was an interaction between a bug fix in the
netvsc driver in 'net' and an optimization of the RX path
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous change to fix checks for NL80211_MESHCONF_HT_OPMODE
missed setting the flag when replacing FILL_IN_MESH_PARAM_IF_SET
with checking codes. This results in dropping the received HT
operation value when called by nl80211_update_mesh_config(). Fix
this by setting the flag properly.
Fixes: 9757235f45 ("nl80211: correct checks for NL80211_MESHCONF_HT_OPMODE value")
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
[rewrite commit message to use Fixes: line]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Slava Shwartsman reported a warning in skb_try_coalesce(), when we
detect skb->truesize is completely wrong.
In his case, issue came from IPv6 reassembly coping with malicious
datagrams, that forced various pskb_may_pull() to reallocate a bigger
skb->head than the one allocated by NIC driver before entering GRO
layer.
Current code does not change skb->truesize, leaving this burden to
callers if they care enough.
Blindly changing skb->truesize in pskb_expand_head() is not
easy, as some producers might track skb->truesize, for example
in xmit path for back pressure feedback (sk->sk_wmem_alloc)
We can detect the cases where it should be safe to change
skb->truesize :
1) skb is not attached to a socket.
2) If it is attached to a socket, destructor is sock_edemux()
My audit gave only two callers doing their own skb->truesize
manipulation.
I had to remove skb parameter in sock_edemux macro when
CONFIG_INET is not set to avoid a compile error.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Slava Shwartsman <slavash@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* socket owner support for connections, so when the wifi
manager (e.g. wpa_supplicant) is killed, connections are
torn down - wpa_supplicant is critical to managing certain
operations, and can opt in to this where applicable
* minstrel & minstrel_ht updates to be more efficient (time and space)
* set wifi_acked/wifi_acked_valid for skb->destructor use in the
kernel, which was already available to userspace
* don't indicate new mesh peers that might be used if there's no
room to add them
* multicast-to-unicast support in mac80211, for better medium usage
(since unicast frames can use *much* higher rates, by ~3 orders of
magnitude)
* add API to read channel (frequency) limitations from DT
* add infrastructure to allow randomizing public action frames for
MAC address privacy (still requires driver support)
* many cleanups and small improvements/fixes across the board
-----BEGIN PGP SIGNATURE-----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=UToW
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For 4.11, we seem to have more than in the past few releases:
* socket owner support for connections, so when the wifi
manager (e.g. wpa_supplicant) is killed, connections are
torn down - wpa_supplicant is critical to managing certain
operations, and can opt in to this where applicable
* minstrel & minstrel_ht updates to be more efficient (time and space)
* set wifi_acked/wifi_acked_valid for skb->destructor use in the
kernel, which was already available to userspace
* don't indicate new mesh peers that might be used if there's no
room to add them
* multicast-to-unicast support in mac80211, for better medium usage
(since unicast frames can use *much* higher rates, by ~3 orders of
magnitude)
* add API to read channel (frequency) limitations from DT
* add infrastructure to allow randomizing public action frames for
MAC address privacy (still requires driver support)
* many cleanups and small improvements/fixes across the board
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This enhances the connect timeout API to also carry the reason for the
timeout. These reason codes for the connect time out are represented by
enum nl80211_timeout_reason and are passed to user space through a new
attribute NL80211_ATTR_TIMEOUT_REASON (u32).
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[keep gfp_t argument last]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enhance sched scan to support option of finding a better BSS while in
connected state. Firmware scans the medium and reports when it finds a
known BSS which has better RSSI than the current connected BSS. New
attributes to specify the relative RSSI (compared to the current BSS)
are added to the sched scan to implement this.
Signed-off-by: vamsi krishna <vamsin@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support to use a random local address (Address 2 = TA in transmit
and the same address in receive functionality) for Public Action frames
in order to improve privacy of WLAN clients. Applications fill the
random transmit address in the frame buffer in the NL80211_CMD_FRAME
command. This can be used only with the drivers that indicate support
for random local address by setting the new
NL80211_EXT_FEATURE_MGMT_TX_RANDOM_TA and/or
NL80211_EXT_FEATURE_MGMT_TX_RANDOM_TA_CONNECTED in ext_features.
The driver needs to configure receive behavior to accept frames to the
specified random address during the time the frame exchange is pending
and such frames need to be acknowledged similarly to frames sent to the
local permanent address when this random address functionality is not
used.
Signed-off-by: vamsi krishna <vamsin@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With 78, 111 and 85 bytes respectively (on x86-64), the
functions iwe_stream_add_event(), iwe_stream_add_point()
and iwe_stream_add_value() really shouldn't be inlines.
It appears that at least my compiler already decided
the same, and created a single instance of each one
of them for each file using it, but that's still a
number of instances in the system overall, which this
reduces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, this attribute is only fetched on station addition, but
not on station change. Since this info is only present in the assoc
request, with full station state support in the driver it cannot be
present when the station is added.
Thus, add support for changing the VHT opmode on station update if
done before (or while) the station is marked as associated. After
this, ignore it, since it used to be ignored.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is not a valid reason to attempt setting the monitor channel
while in managed mode. Since this code path only deals with this mode,
remove the code block.
Johannes: I'll note that the comment indicated it was for backward
compatibility, but the code wasn't functional since switching the
monitor channel isn't supported (any more?) when in managed mode, as
that mode owns the channel configuration. Additionally, since monitor
can't be done on a managed mode interface, this would only have had
any effect to start with if a separate monitor interface is present,
in which case it's better to change the channel through that anyway,
if even possible.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Disconnect or deauthenticate when the owning socket is closed if this
flag is supplied to CMD_CONNECT or CMD_ASSOCIATE. This may be used
to ensure userspace daemon doesn't leave an unmanaged connection behind.
In some situations it would be possible to account for that, to some
degree, in the deamon restart code or in the up/down scripts without
the use of this attribute. But there will be systems where the daemon
can go away for varying periods without a warning due to local resource
management.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ilan reported that sometimes nl80211 messages weren't working if
the frames being transported got very large, which was really a
problem for userspace-to-kernel messages, but prompted me to look
at the code.
Upon review, I found various places where variable-length data is
transported in an nl80211 message but the message isn't allocated
taking that into account. This shouldn't cause any problems since
the frames aren't really that long, apart in one place where two
(possibly very long frames) might not fit.
Fix all the places (that I found) that get variable length data
from the driver and put it into a message to take the length of
the variable data into account. The 100 there is just a safe
constant for the remaining message overhead (it's usually around
50 for most messages.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds a helper for reading that new property and applying
limitations of supported channels specified this way.
It is used with devices that normally support a wide wireless band but
in a given config are limited to some part of it (usually due to board
design). For example a dual-band chipset may be able to support one band
only because of used antennas.
It's also common that tri-band routers have separated radios for lower
and higher part of 5 GHz band and it may be impossible to say which is
which without a DT info.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
[add new function to documentation, fix link]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is needed for another cfg80211 helper that will be out of reg.c so
move it to common util.c file and make it non-static.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The supported band structure contains the band is applies to
so no need to pass it separately. Also added a default case
to the switch for completeness. The current code base does not
call this function with NUM_NL80211_BANDS but kept that case
statement although default case would cover that.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A single netlink socket might own multiple interfaces *and* a
scheduled scan request (which might belong to another interface),
so when it goes away both may need to be destroyed.
Remove the schedule_scan_stop indirection to fix this - it's only
needed for interface destruction because of the way this works
right now, with a single work taking care of all interfaces.
Cc: stable@vger.kernel.org
Fixes: 93a1e86ce1 ("nl80211: Stop scheduled scan if netlink client disappears")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of open-coding dev_name(), use the wiphy_name() inline
to make the code easier to understand. While at it, clean up
some coding style.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A couple of functions used with scan events were named with
term "send" although they were only preparing the the event
message so renamed those.
Also remove nl80211_send_sched_scan_results() in favor of
just calling nl80211_send_sched_scan() with the right value.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[mention nl80211_send_sched_scan_results() in the commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
That's the default now, no need for makefiles to set it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
There is no need to prevent toggling multicast_to_unicast while
interface is already up. This change simplifies reconfiguration
from hostapd.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The presence of the NL80211_ATTR_SCHED_SCAN_INTERVAL attribute was
checked in nl80211_parse_sched_scan() and
nl80211_parse_sched_scan_plans() which might be a bit redundant
so removing one.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The comment on the name indirection suggested an issue but turned out
to be untrue. Digging in older kernel version showed issue with ipw2x00
but that is no longer true so get rid on the name indirection.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* fix a logic bug introduced by a previous cleanup
* fix nl80211 attribute confusing (trying to use
a single attribute for two purposes)
* fix a long-standing BSS leak that happens when an
association attempt is abandoned
-----BEGIN PGP SIGNATURE-----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=HvKt
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-12-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Three fixes:
* fix a logic bug introduced by a previous cleanup
* fix nl80211 attribute confusing (trying to use
a single attribute for two purposes)
* fix a long-standing BSS leak that happens when an
association attempt is abandoned
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When mac80211 abandons an association attempt, it may free
all the data structures, but inform cfg80211 and userspace
about it only by sending the deauth frame it received, in
which case cfg80211 has no link to the BSS struct that was
used and will not cfg80211_unhold_bss() it.
Fix this by providing a way to inform cfg80211 of this with
the BSS entry passed, so that it can clean up properly, and
use this ability in the appropriate places in mac80211.
This isn't ideal: some code is more or less duplicated and
tracing is missing. However, it's a fairly small change and
it's thus easier to backport - cleanups can come later.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
NL80211_ATTR_MAC was used to set both the specific BSSID to be scanned
and the random MAC address to be used when privacy is enabled. When both
the features are enabled, both the BSSID and the local MAC address were
getting same value causing Probe Request frames to go with unintended
DA. Hence, this has been fixed by using a different NL80211_ATTR_BSSID
attribute to set the specific BSSID (which was the more recent addition
in cfg80211) for a scan.
Backwards compatibility with old userspace software is maintained to
some extent by allowing NL80211_ATTR_MAC to be used to set the specific
BSSID when scanning without enabling random MAC address use.
Scanning with random source MAC address was introduced by commit
ad2b26abc1 ("cfg80211: allow drivers to support random MAC addresses
for scan") and the issue was introduced with the addition of the second
user for the same attribute in commit 818965d391 ("cfg80211: Allow a
scan request for a specific BSSID").
Fixes: 818965d391 ("cfg80211: Allow a scan request for a specific BSSID")
Signed-off-by: Vamsi Krishna <vamsin@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arend inadvertently inverted the logic while converting to
wdev_running(), fix that.
Fixes: 73c7da3dae ("cfg80211: add generic helper to check interface is running")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYOAC4AAoJEG4XJFUm622bUYkH/3SSYp6moSdKpVnVPx7ST7yK
t9WHR9IMZFIhD6vq8AK6+8OQr1TgGjHfPu+WZj7CIl8nu53kcgPRi51gg1mndbNg
9N3RbVp06nGbM2VnW8ZIpg3OLIXatZ4c9g3LFvvtyobYvWGJ6W4D79JdlmTG1ELr
XAjInbxFsgon+CwqCMOaAJx8xYp42rBnPRZZvhOq9O33kRw8Umo9UQw0s1U2Vfgx
prxQ6d0GxNAPEe8QiDw/vtBcXWFMOhQeDl8sK70ZcojSn1FY730NsIh/Y86PcQTK
6TsvOL5gg+rd0ln8TZRAslnDrZBAhTEDqUzLQMRJ9VjEj5RFd8eLCSIzHfaroI8=
=4qCH
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-11-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible to make scanning consume almost arbitrary amounts
of memory, e.g. by sending beacon frames with random BSSIDs at
high rates while somebody is scanning.
Limit the number of BSS table entries we're willing to cache to
1000, limiting maximum memory usage to maybe 4-5MB, but lower
in practice - that would be the case for having both full-sized
beacon and probe response frames for each entry; this seems not
possible in practice, so a limit of 1000 entries will likely be
closer to 0.5 MB.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The hostap_80211_rx() function is supposed to set up the mac addresses
for four possible cases, based on two bits of input data. For
some reason, gcc decides that it's possible that none of the these
four cases apply and the addresses remain uninitialized:
drivers/net/wireless/intersil/hostap/hostap_80211_rx.c: In function ‘hostap_80211_rx’:
arch/x86/include/asm/string_32.h:77:14: warning: ‘src’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/net/wireless/intel/ipw2x00/libipw_rx.c: In function ‘libipw_rx’:
arch/x86/include/asm/string_32.h:77:14: error: ‘dst’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
arch/x86/include/asm/string_32.h:78:22: error: ‘*((void *)&dst+4)’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
This warning is clearly nonsense, but changing the last case into
'default' makes it obvious to the compiler too, which avoids the
warning and probably leads to better object code too.
The same code is duplicated several times in the kernel, so this
patch uses the same workaround for all copies. The exact configuration
was hit only very rarely in randconfig builds and I only saw it
in three drivers, but I assume that all of them are potentially
affected, and it's better to keep the code consistent.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some drivers (ath10k) report MCS 9 @ 20MHz, which
technically isn't defined. To get more meaningful value
than 0 out of this however, just extrapolate a bitrate
from ratio of MCS 7 and 9 in channels where it is allowed.
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
[add a comment about it in the code]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
* client FILS authentication support in mac80211 (Jouni)
* AP/VLAN multicast improvements (Michael Braun)
* config/advertising support for differing beacon intervals on
multiple virtual interfaces (Purushottam Kushwaha, myself)
* deprecate the old WDS mode for cfg80211-based drivers, the
mode is hardly usable since it doesn't support any "modern"
features like WPA encryption (2003), HT (2009) or VHT (2014),
I'm not even sure WEP (introduced in 1997) could be done.
-----BEGIN PGP SIGNATURE-----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=SjfQ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-10-28' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Among various cleanups and improvements, we have the following:
* client FILS authentication support in mac80211 (Jouni)
* AP/VLAN multicast improvements (Michael Braun)
* config/advertising support for differing beacon intervals on
multiple virtual interfaces (Purushottam Kushwaha, myself)
* deprecate the old WDS mode for cfg80211-based drivers, the
mode is hardly usable since it doesn't support any "modern"
features like WPA encryption (2003), HT (2009) or VHT (2014),
I'm not even sure WEP (introduced in 1997) could be done.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrap several common instances of:
kmemdup(nla_data(attr), nla_len(attr), GFP_KERNEL);
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now genl_register_family() is the only thing (other than the
users themselves, perhaps, but I didn't find any doing that)
writing to the family struct.
In all families that I found, genl_register_family() is only
called from __init functions (some indirectly, in which case
I've add __init annotations to clarifly things), so all can
actually be marked __ro_after_init.
This protects the data structure from accidental corruption.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of providing macros/inline functions to initialize
the families, make all users initialize them statically and
get rid of the macros.
This reduces the kernel code size by about 1.6k on x86-64
(with allyesconfig).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Static family IDs have never really been used, the only
use case was the workaround I introduced for those users
that assumed their family ID was also their multicast
group ID.
Additionally, because static family IDs would never be
reserved by the generic netlink code, using a relatively
low ID would only work for built-in families that can be
registered immediately after generic netlink is started,
which is basically only the control family (apart from
the workaround code, which I also had to add code for so
it would reserve those IDs)
Thus, anything other than GENL_ID_GENERATE is flawed and
luckily not used except in the cases I mentioned. Move
those workarounds into a few lines of code, and then get
rid of GENL_ID_GENERATE entirely, making it more robust.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This helper function allows family implementations to access
their family's attrbuf. This gets rid of the attrbuf usage
in families, and also adds locking validation, since it's not
valid to use the attrbuf with parallel_ops or outside of the
dumpit callback.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functionality to update the connection parameters when in connected
state, so that driver/firmware uses the updated parameters for
subsequent roaming. This is for drivers that support internal BSS
selection and roaming. The new command does not change the current
association state, i.e., it can be used to update IE contents for future
(re)associations without causing an immediate disassociation or
reassociation with the current BSS.
This commit implements the required functionality for updating IEs for
(Re)Association Request frame only. Other parameters can be added in
future when required.
Signed-off-by: vamsi krishna <vamsin@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The IEs "output" can sometimes combine IEs coming from userspace
with IEs generated in the kernel - in particular mac80211 does
this for association frames.
Add support in this code for the 802.11 IE fragmentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arend Van Spriel