![Javier Martinez Canillas](/assets/img/avatar_default.png)
The tvp5150 video decoder has two operation modes to configure the video standard used. If auto-switch mode is enable, the device can sense the signal and detect which video standard the device is operating. Also the device can be forced to use a user defined video standard. Each operation mode uses a different register and the bitmask values to represent each standard is different. So we add video standard constants for both autoswitch and no-autoswitch mode. Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
140 lines
6.4 KiB
C
140 lines
6.4 KiB
C
/*
|
|
* tvp5150 - Texas Instruments TVP5150A/AM1 video decoder registers
|
|
*
|
|
* Copyright (c) 2005,2006 Mauro Carvalho Chehab (mchehab@infradead.org)
|
|
* This code is placed under the terms of the GNU General Public License v2
|
|
*/
|
|
|
|
#define TVP5150_VD_IN_SRC_SEL_1 0x00 /* Video input source selection #1 */
|
|
#define TVP5150_ANAL_CHL_CTL 0x01 /* Analog channel controls */
|
|
#define TVP5150_OP_MODE_CTL 0x02 /* Operation mode controls */
|
|
#define TVP5150_MISC_CTL 0x03 /* Miscellaneous controls */
|
|
#define TVP5150_AUTOSW_MSK 0x04 /* Autoswitch mask: TVP5150A / TVP5150AM */
|
|
|
|
/* Reserved 05h */
|
|
|
|
#define TVP5150_COLOR_KIL_THSH_CTL 0x06 /* Color killer threshold control */
|
|
#define TVP5150_LUMA_PROC_CTL_1 0x07 /* Luminance processing control #1 */
|
|
#define TVP5150_LUMA_PROC_CTL_2 0x08 /* Luminance processing control #2 */
|
|
#define TVP5150_BRIGHT_CTL 0x09 /* Brightness control */
|
|
#define TVP5150_SATURATION_CTL 0x0a /* Color saturation control */
|
|
#define TVP5150_HUE_CTL 0x0b /* Hue control */
|
|
#define TVP5150_CONTRAST_CTL 0x0c /* Contrast control */
|
|
#define TVP5150_DATA_RATE_SEL 0x0d /* Outputs and data rates select */
|
|
#define TVP5150_LUMA_PROC_CTL_3 0x0e /* Luminance processing control #3 */
|
|
#define TVP5150_CONF_SHARED_PIN 0x0f /* Configuration shared pins */
|
|
|
|
/* Reserved 10h */
|
|
|
|
#define TVP5150_ACT_VD_CROP_ST_MSB 0x11 /* Active video cropping start MSB */
|
|
#define TVP5150_ACT_VD_CROP_ST_LSB 0x12 /* Active video cropping start LSB */
|
|
#define TVP5150_ACT_VD_CROP_STP_MSB 0x13 /* Active video cropping stop MSB */
|
|
#define TVP5150_ACT_VD_CROP_STP_LSB 0x14 /* Active video cropping stop LSB */
|
|
#define TVP5150_GENLOCK 0x15 /* Genlock/RTC */
|
|
#define TVP5150_HORIZ_SYNC_START 0x16 /* Horizontal sync start */
|
|
|
|
/* Reserved 17h */
|
|
|
|
#define TVP5150_VERT_BLANKING_START 0x18 /* Vertical blanking start */
|
|
#define TVP5150_VERT_BLANKING_STOP 0x19 /* Vertical blanking stop */
|
|
#define TVP5150_CHROMA_PROC_CTL_1 0x1a /* Chrominance processing control #1 */
|
|
#define TVP5150_CHROMA_PROC_CTL_2 0x1b /* Chrominance processing control #2 */
|
|
#define TVP5150_INT_RESET_REG_B 0x1c /* Interrupt reset register B */
|
|
#define TVP5150_INT_ENABLE_REG_B 0x1d /* Interrupt enable register B */
|
|
#define TVP5150_INTT_CONFIG_REG_B 0x1e /* Interrupt configuration register B */
|
|
|
|
/* Reserved 1Fh-27h */
|
|
|
|
#define VIDEO_STD_MASK (0x07 >> 1)
|
|
#define TVP5150_VIDEO_STD 0x28 /* Video standard */
|
|
#define VIDEO_STD_AUTO_SWITCH_BIT 0x00
|
|
#define VIDEO_STD_NTSC_MJ_BIT 0x02
|
|
#define VIDEO_STD_PAL_BDGHIN_BIT 0x04
|
|
#define VIDEO_STD_PAL_M_BIT 0x06
|
|
#define VIDEO_STD_PAL_COMBINATION_N_BIT 0x08
|
|
#define VIDEO_STD_NTSC_4_43_BIT 0x0a
|
|
#define VIDEO_STD_SECAM_BIT 0x0c
|
|
|
|
#define VIDEO_STD_NTSC_MJ_BIT_AS 0x01
|
|
#define VIDEO_STD_PAL_BDGHIN_BIT_AS 0x03
|
|
#define VIDEO_STD_PAL_M_BIT_AS 0x05
|
|
#define VIDEO_STD_PAL_COMBINATION_N_BIT_AS 0x07
|
|
#define VIDEO_STD_NTSC_4_43_BIT_AS 0x09
|
|
#define VIDEO_STD_SECAM_BIT_AS 0x0b
|
|
|
|
/* Reserved 29h-2bh */
|
|
|
|
#define TVP5150_CB_GAIN_FACT 0x2c /* Cb gain factor */
|
|
#define TVP5150_CR_GAIN_FACTOR 0x2d /* Cr gain factor */
|
|
#define TVP5150_MACROVISION_ON_CTR 0x2e /* Macrovision on counter */
|
|
#define TVP5150_MACROVISION_OFF_CTR 0x2f /* Macrovision off counter */
|
|
#define TVP5150_REV_SELECT 0x30 /* revision select (TVP5150AM1 only) */
|
|
|
|
/* Reserved 31h-7Fh */
|
|
|
|
#define TVP5150_MSB_DEV_ID 0x80 /* MSB of device ID */
|
|
#define TVP5150_LSB_DEV_ID 0x81 /* LSB of device ID */
|
|
#define TVP5150_ROM_MAJOR_VER 0x82 /* ROM major version */
|
|
#define TVP5150_ROM_MINOR_VER 0x83 /* ROM minor version */
|
|
#define TVP5150_VERT_LN_COUNT_MSB 0x84 /* Vertical line count MSB */
|
|
#define TVP5150_VERT_LN_COUNT_LSB 0x85 /* Vertical line count LSB */
|
|
#define TVP5150_INT_STATUS_REG_B 0x86 /* Interrupt status register B */
|
|
#define TVP5150_INT_ACTIVE_REG_B 0x87 /* Interrupt active register B */
|
|
#define TVP5150_STATUS_REG_1 0x88 /* Status register #1 */
|
|
#define TVP5150_STATUS_REG_2 0x89 /* Status register #2 */
|
|
#define TVP5150_STATUS_REG_3 0x8a /* Status register #3 */
|
|
#define TVP5150_STATUS_REG_4 0x8b /* Status register #4 */
|
|
#define TVP5150_STATUS_REG_5 0x8c /* Status register #5 */
|
|
/* Reserved 8Dh-8Fh */
|
|
/* Closed caption data registers */
|
|
#define TVP5150_CC_DATA_INI 0x90
|
|
#define TVP5150_CC_DATA_END 0x93
|
|
|
|
/* WSS data registers */
|
|
#define TVP5150_WSS_DATA_INI 0x94
|
|
#define TVP5150_WSS_DATA_END 0x99
|
|
|
|
/* VPS data registers */
|
|
#define TVP5150_VPS_DATA_INI 0x9a
|
|
#define TVP5150_VPS_DATA_END 0xa6
|
|
|
|
/* VITC data registers */
|
|
#define TVP5150_VITC_DATA_INI 0xa7
|
|
#define TVP5150_VITC_DATA_END 0xaf
|
|
|
|
#define TVP5150_VBI_FIFO_READ_DATA 0xb0 /* VBI FIFO read data */
|
|
|
|
/* Teletext filter 1 */
|
|
#define TVP5150_TELETEXT_FIL1_INI 0xb1
|
|
#define TVP5150_TELETEXT_FIL1_END 0xb5
|
|
|
|
/* Teletext filter 2 */
|
|
#define TVP5150_TELETEXT_FIL2_INI 0xb6
|
|
#define TVP5150_TELETEXT_FIL2_END 0xba
|
|
|
|
#define TVP5150_TELETEXT_FIL_ENA 0xbb /* Teletext filter enable */
|
|
/* Reserved BCh-BFh */
|
|
#define TVP5150_INT_STATUS_REG_A 0xc0 /* Interrupt status register A */
|
|
#define TVP5150_INT_ENABLE_REG_A 0xc1 /* Interrupt enable register A */
|
|
#define TVP5150_INT_CONF 0xc2 /* Interrupt configuration */
|
|
#define TVP5150_VDP_CONF_RAM_DATA 0xc3 /* VDP configuration RAM data */
|
|
#define TVP5150_CONF_RAM_ADDR_LOW 0xc4 /* Configuration RAM address low byte */
|
|
#define TVP5150_CONF_RAM_ADDR_HIGH 0xc5 /* Configuration RAM address high byte */
|
|
#define TVP5150_VDP_STATUS_REG 0xc6 /* VDP status register */
|
|
#define TVP5150_FIFO_WORD_COUNT 0xc7 /* FIFO word count */
|
|
#define TVP5150_FIFO_INT_THRESHOLD 0xc8 /* FIFO interrupt threshold */
|
|
#define TVP5150_FIFO_RESET 0xc9 /* FIFO reset */
|
|
#define TVP5150_LINE_NUMBER_INT 0xca /* Line number interrupt */
|
|
#define TVP5150_PIX_ALIGN_REG_LOW 0xcb /* Pixel alignment register low byte */
|
|
#define TVP5150_PIX_ALIGN_REG_HIGH 0xcc /* Pixel alignment register high byte */
|
|
#define TVP5150_FIFO_OUT_CTRL 0xcd /* FIFO output control */
|
|
/* Reserved CEh */
|
|
#define TVP5150_FULL_FIELD_ENA 0xcf /* Full field enable 1 */
|
|
|
|
/* Line mode registers */
|
|
#define TVP5150_LINE_MODE_INI 0xd0
|
|
#define TVP5150_LINE_MODE_END 0xfb
|
|
|
|
#define TVP5150_FULL_FIELD_MODE_REG 0xfc /* Full field mode register */
|
|
/* Reserved FDh-FFh */
|