53f73c09d6
When roaming while we have active BA session, we can end up transmitting delBA frames to the old AP while we're already on the new AP's channel, which can cause warnings. Simply avoid sending those frames, but still tear down the internal session state, since they are not really necessary anyway as we will implicitly disassociate when sending the association to the new AP. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
115 lines
2.7 KiB
C
115 lines
2.7 KiB
C
#include <net/mac80211.h>
|
|
#include <net/rtnetlink.h>
|
|
|
|
#include "ieee80211_i.h"
|
|
#include "mesh.h"
|
|
#include "driver-ops.h"
|
|
#include "led.h"
|
|
|
|
int __ieee80211_suspend(struct ieee80211_hw *hw)
|
|
{
|
|
struct ieee80211_local *local = hw_to_local(hw);
|
|
struct ieee80211_sub_if_data *sdata;
|
|
struct sta_info *sta;
|
|
|
|
if (unlikely(test_bit(SCAN_SW_SCANNING, &local->scanning)))
|
|
ieee80211_scan_cancel(local);
|
|
|
|
ieee80211_stop_queues_by_reason(hw,
|
|
IEEE80211_QUEUE_STOP_REASON_SUSPEND);
|
|
|
|
/* flush out all packets */
|
|
synchronize_net();
|
|
|
|
local->quiescing = true;
|
|
/* make quiescing visible to timers everywhere */
|
|
mb();
|
|
|
|
flush_workqueue(local->workqueue);
|
|
|
|
/* Don't try to run timers while suspended. */
|
|
del_timer_sync(&local->sta_cleanup);
|
|
|
|
/*
|
|
* Note that this particular timer doesn't need to be
|
|
* restarted at resume.
|
|
*/
|
|
cancel_work_sync(&local->dynamic_ps_enable_work);
|
|
del_timer_sync(&local->dynamic_ps_timer);
|
|
|
|
/* disable keys */
|
|
list_for_each_entry(sdata, &local->interfaces, list)
|
|
ieee80211_disable_keys(sdata);
|
|
|
|
/* tear down aggregation sessions and remove STAs */
|
|
mutex_lock(&local->sta_mtx);
|
|
list_for_each_entry(sta, &local->sta_list, list) {
|
|
if (hw->flags & IEEE80211_HW_AMPDU_AGGREGATION) {
|
|
set_sta_flags(sta, WLAN_STA_BLOCK_BA);
|
|
ieee80211_sta_tear_down_BA_sessions(sta, true);
|
|
}
|
|
|
|
if (sta->uploaded) {
|
|
sdata = sta->sdata;
|
|
if (sdata->vif.type == NL80211_IFTYPE_AP_VLAN)
|
|
sdata = container_of(sdata->bss,
|
|
struct ieee80211_sub_if_data,
|
|
u.ap);
|
|
|
|
drv_sta_remove(local, sdata, &sta->sta);
|
|
}
|
|
|
|
mesh_plink_quiesce(sta);
|
|
}
|
|
mutex_unlock(&local->sta_mtx);
|
|
|
|
/* remove all interfaces */
|
|
list_for_each_entry(sdata, &local->interfaces, list) {
|
|
cancel_work_sync(&sdata->work);
|
|
|
|
switch(sdata->vif.type) {
|
|
case NL80211_IFTYPE_STATION:
|
|
ieee80211_sta_quiesce(sdata);
|
|
break;
|
|
case NL80211_IFTYPE_ADHOC:
|
|
ieee80211_ibss_quiesce(sdata);
|
|
break;
|
|
case NL80211_IFTYPE_MESH_POINT:
|
|
ieee80211_mesh_quiesce(sdata);
|
|
break;
|
|
case NL80211_IFTYPE_AP_VLAN:
|
|
case NL80211_IFTYPE_MONITOR:
|
|
/* don't tell driver about this */
|
|
continue;
|
|
default:
|
|
break;
|
|
}
|
|
|
|
if (!ieee80211_sdata_running(sdata))
|
|
continue;
|
|
|
|
/* disable beaconing */
|
|
ieee80211_bss_info_change_notify(sdata,
|
|
BSS_CHANGED_BEACON_ENABLED);
|
|
|
|
drv_remove_interface(local, &sdata->vif);
|
|
}
|
|
|
|
/* stop hardware - this must stop RX */
|
|
if (local->open_count)
|
|
ieee80211_stop_device(local);
|
|
|
|
local->suspended = true;
|
|
/* need suspended to be visible before quiescing is false */
|
|
barrier();
|
|
local->quiescing = false;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* __ieee80211_resume() is a static inline which just calls
|
|
* ieee80211_reconfig(), which is also needed for hardware
|
|
* hang/firmware failure/etc. recovery.
|
|
*/
|