remarkable-linux/drivers/Makefile
Srinivas Kandagatla eace75cfdc nvmem: Add a simple NVMEM framework for nvmem providers
This patch adds just providers part of the framework just to enable easy
review.

Up until now, NVMEM drivers like eeprom were stored in drivers/misc,
where they all had to duplicate pretty much the same code to register
a sysfs file, allow in-kernel users to access the content of the devices
they were driving, etc.

This was also a problem as far as other in-kernel users were involved,
since the solutions used were pretty much different from on driver to
another, there was a rather big abstraction leak.

This introduction of this framework aims at solving this. It also
introduces DT representation for consumer devices to go get the data
they require (MAC Addresses, SoC/Revision ID, part numbers, and so on)
from the nvmems.

Having regmap interface to this framework would give much better
abstraction for nvmems on different buses.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[Maxime Ripard: intial version of eeprom framework]
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-08-05 13:43:12 -07:00

169 lines
4.7 KiB
Makefile

#
# Makefile for the Linux kernel device drivers.
#
# 15 Sep 2000, Christoph Hellwig <hch@infradead.org>
# Rewritten to use lists instead of if-statements.
#
obj-y += irqchip/
obj-y += bus/
obj-$(CONFIG_GENERIC_PHY) += phy/
# GPIO must come after pinctrl as gpios may need to mux pins etc
obj-y += pinctrl/
obj-y += gpio/
obj-y += pwm/
obj-$(CONFIG_PCI) += pci/
obj-$(CONFIG_PARISC) += parisc/
obj-$(CONFIG_RAPIDIO) += rapidio/
obj-y += video/
obj-y += idle/
# IPMI must come before ACPI in order to provide IPMI opregion support
obj-$(CONFIG_IPMI_HANDLER) += char/ipmi/
obj-$(CONFIG_ACPI) += acpi/
obj-$(CONFIG_SFI) += sfi/
# PnP must come after ACPI since it will eventually need to check if acpi
# was used and do nothing if so
obj-$(CONFIG_PNP) += pnp/
obj-y += amba/
# Many drivers will want to use DMA so this has to be made available
# really early.
obj-$(CONFIG_DMADEVICES) += dma/
# SOC specific infrastructure drivers.
obj-y += soc/
obj-$(CONFIG_VIRTIO) += virtio/
obj-$(CONFIG_XEN) += xen/
# regulators early, since some subsystems rely on them to initialize
obj-$(CONFIG_REGULATOR) += regulator/
# reset controllers early, since gpu drivers might rely on them to initialize
obj-$(CONFIG_RESET_CONTROLLER) += reset/
# tty/ comes before char/ so that the VT console is the boot-time
# default.
obj-y += tty/
obj-y += char/
# iommu/ comes before gpu as gpu are using iommu controllers
obj-$(CONFIG_IOMMU_SUPPORT) += iommu/
# gpu/ comes after char for AGP vs DRM startup and after iommu
obj-y += gpu/
obj-$(CONFIG_CONNECTOR) += connector/
# i810fb and intelfb depend on char/agp/
obj-$(CONFIG_FB_I810) += video/fbdev/i810/
obj-$(CONFIG_FB_INTEL) += video/fbdev/intelfb/
obj-$(CONFIG_PARPORT) += parport/
obj-y += base/ block/ misc/ mfd/ nfc/
obj-$(CONFIG_LIBNVDIMM) += nvdimm/
obj-$(CONFIG_DMA_SHARED_BUFFER) += dma-buf/
obj-$(CONFIG_NUBUS) += nubus/
obj-y += macintosh/
obj-$(CONFIG_IDE) += ide/
obj-$(CONFIG_SCSI) += scsi/
obj-$(CONFIG_ATA) += ata/
obj-$(CONFIG_TARGET_CORE) += target/
obj-$(CONFIG_MTD) += mtd/
obj-$(CONFIG_SPI) += spi/
obj-$(CONFIG_SPMI) += spmi/
obj-y += hsi/
obj-y += net/
obj-$(CONFIG_ATM) += atm/
obj-$(CONFIG_FUSION) += message/
obj-y += firewire/
obj-$(CONFIG_UIO) += uio/
obj-$(CONFIG_VFIO) += vfio/
obj-y += cdrom/
obj-y += auxdisplay/
obj-$(CONFIG_PCCARD) += pcmcia/
obj-$(CONFIG_DIO) += dio/
obj-$(CONFIG_SBUS) += sbus/
obj-$(CONFIG_ZORRO) += zorro/
obj-$(CONFIG_ATA_OVER_ETH) += block/aoe/
obj-$(CONFIG_PARIDE) += block/paride/
obj-$(CONFIG_TC) += tc/
obj-$(CONFIG_UWB) += uwb/
obj-$(CONFIG_USB_PHY) += usb/
obj-$(CONFIG_USB) += usb/
obj-$(CONFIG_PCI) += usb/
obj-$(CONFIG_USB_GADGET) += usb/
obj-$(CONFIG_SERIO) += input/serio/
obj-$(CONFIG_GAMEPORT) += input/gameport/
obj-$(CONFIG_INPUT) += input/
obj-$(CONFIG_RTC_LIB) += rtc/
obj-y += i2c/ media/
obj-$(CONFIG_PPS) += pps/
obj-$(CONFIG_PTP_1588_CLOCK) += ptp/
obj-$(CONFIG_W1) += w1/
obj-$(CONFIG_POWER_SUPPLY) += power/
obj-$(CONFIG_HWMON) += hwmon/
obj-$(CONFIG_THERMAL) += thermal/
obj-$(CONFIG_WATCHDOG) += watchdog/
obj-$(CONFIG_MD) += md/
obj-$(CONFIG_BT) += bluetooth/
obj-$(CONFIG_ACCESSIBILITY) += accessibility/
obj-$(CONFIG_ISDN) += isdn/
obj-$(CONFIG_EDAC) += edac/
obj-$(CONFIG_EISA) += eisa/
obj-y += lguest/
obj-$(CONFIG_CPU_FREQ) += cpufreq/
obj-$(CONFIG_CPU_IDLE) += cpuidle/
obj-y += mmc/
obj-$(CONFIG_MEMSTICK) += memstick/
obj-y += leds/
obj-$(CONFIG_INFINIBAND) += infiniband/
obj-$(CONFIG_SGI_SN) += sn/
obj-y += firmware/
obj-$(CONFIG_CRYPTO) += crypto/
obj-$(CONFIG_SUPERH) += sh/
obj-$(CONFIG_ARCH_SHMOBILE) += sh/
ifndef CONFIG_ARCH_USES_GETTIMEOFFSET
obj-y += clocksource/
endif
obj-$(CONFIG_DCA) += dca/
obj-$(CONFIG_HID) += hid/
obj-$(CONFIG_PPC_PS3) += ps3/
obj-$(CONFIG_OF) += of/
obj-$(CONFIG_SSB) += ssb/
obj-$(CONFIG_BCMA) += bcma/
obj-$(CONFIG_VHOST_RING) += vhost/
obj-$(CONFIG_VLYNQ) += vlynq/
obj-$(CONFIG_STAGING) += staging/
obj-y += platform/
#common clk code
obj-y += clk/
obj-$(CONFIG_MAILBOX) += mailbox/
obj-$(CONFIG_HWSPINLOCK) += hwspinlock/
obj-$(CONFIG_REMOTEPROC) += remoteproc/
obj-$(CONFIG_RPMSG) += rpmsg/
# Virtualization drivers
obj-$(CONFIG_VIRT_DRIVERS) += virt/
obj-$(CONFIG_HYPERV) += hv/
obj-$(CONFIG_PM_DEVFREQ) += devfreq/
obj-$(CONFIG_EXTCON) += extcon/
obj-$(CONFIG_MEMORY) += memory/
obj-$(CONFIG_IIO) += iio/
obj-$(CONFIG_VME_BUS) += vme/
obj-$(CONFIG_IPACK_BUS) += ipack/
obj-$(CONFIG_NTB) += ntb/
obj-$(CONFIG_FMC) += fmc/
obj-$(CONFIG_POWERCAP) += powercap/
obj-$(CONFIG_MCB) += mcb/
obj-$(CONFIG_RAS) += ras/
obj-$(CONFIG_THUNDERBOLT) += thunderbolt/
obj-$(CONFIG_CORESIGHT) += hwtracing/coresight/
obj-$(CONFIG_ANDROID) += android/
obj-$(CONFIG_NVMEM) += nvmem/