1640f28f6b
Newer WiFi chip use ARM CR4 core to achieve higher performance. Add necessary code for host driver in order to support CR4 core. Reviewed-by: Arend van Spriel <arend@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Franky Lin <frankyl@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
95 lines
4.7 KiB
C
95 lines
4.7 KiB
C
#ifndef LINUX_BCMA_REGS_H_
|
|
#define LINUX_BCMA_REGS_H_
|
|
|
|
/* Some single registers are shared between many cores */
|
|
/* BCMA_CLKCTLST: ChipCommon (rev >= 20), PCIe, 80211 */
|
|
#define BCMA_CLKCTLST 0x01E0 /* Clock control and status */
|
|
#define BCMA_CLKCTLST_FORCEALP 0x00000001 /* Force ALP request */
|
|
#define BCMA_CLKCTLST_FORCEHT 0x00000002 /* Force HT request */
|
|
#define BCMA_CLKCTLST_FORCEILP 0x00000004 /* Force ILP request */
|
|
#define BCMA_CLKCTLST_HAVEALPREQ 0x00000008 /* ALP available request */
|
|
#define BCMA_CLKCTLST_HAVEHTREQ 0x00000010 /* HT available request */
|
|
#define BCMA_CLKCTLST_HWCROFF 0x00000020 /* Force HW clock request off */
|
|
#define BCMA_CLKCTLST_EXTRESREQ 0x00000700 /* Mask of external resource requests */
|
|
#define BCMA_CLKCTLST_EXTRESREQ_SHIFT 8
|
|
#define BCMA_CLKCTLST_HAVEALP 0x00010000 /* ALP available */
|
|
#define BCMA_CLKCTLST_HAVEHT 0x00020000 /* HT available */
|
|
#define BCMA_CLKCTLST_BP_ON_ALP 0x00040000 /* RO: running on ALP clock */
|
|
#define BCMA_CLKCTLST_BP_ON_HT 0x00080000 /* RO: running on HT clock */
|
|
#define BCMA_CLKCTLST_EXTRESST 0x07000000 /* Mask of external resource status */
|
|
#define BCMA_CLKCTLST_EXTRESST_SHIFT 24
|
|
/* Is there any BCM4328 on BCMA bus? */
|
|
#define BCMA_CLKCTLST_4328A0_HAVEHT 0x00010000 /* 4328a0 has reversed bits */
|
|
#define BCMA_CLKCTLST_4328A0_HAVEALP 0x00020000 /* 4328a0 has reversed bits */
|
|
|
|
/* Agent registers (common for every core) */
|
|
#define BCMA_IOCTL 0x0408 /* IO control */
|
|
#define BCMA_IOCTL_CLK 0x0001
|
|
#define BCMA_IOCTL_FGC 0x0002
|
|
#define BCMA_IOCTL_CORE_BITS 0x3FFC
|
|
#define BCMA_IOCTL_PME_EN 0x4000
|
|
#define BCMA_IOCTL_BIST_EN 0x8000
|
|
#define BCMA_IOST 0x0500 /* IO status */
|
|
#define BCMA_IOST_CORE_BITS 0x0FFF
|
|
#define BCMA_IOST_DMA64 0x1000
|
|
#define BCMA_IOST_GATED_CLK 0x2000
|
|
#define BCMA_IOST_BIST_ERROR 0x4000
|
|
#define BCMA_IOST_BIST_DONE 0x8000
|
|
#define BCMA_RESET_CTL 0x0800
|
|
#define BCMA_RESET_CTL_RESET 0x0001
|
|
#define BCMA_RESET_ST 0x0804
|
|
|
|
/* BCMA PCI config space registers. */
|
|
#define BCMA_PCI_PMCSR 0x44
|
|
#define BCMA_PCI_PE 0x100
|
|
#define BCMA_PCI_BAR0_WIN 0x80 /* Backplane address space 0 */
|
|
#define BCMA_PCI_BAR1_WIN 0x84 /* Backplane address space 1 */
|
|
#define BCMA_PCI_SPROMCTL 0x88 /* SPROM control */
|
|
#define BCMA_PCI_SPROMCTL_WE 0x10 /* SPROM write enable */
|
|
#define BCMA_PCI_BAR1_CONTROL 0x8c /* Address space 1 burst control */
|
|
#define BCMA_PCI_IRQS 0x90 /* PCI interrupts */
|
|
#define BCMA_PCI_IRQMASK 0x94 /* PCI IRQ control and mask (pcirev >= 6 only) */
|
|
#define BCMA_PCI_BACKPLANE_IRQS 0x98 /* Backplane Interrupts */
|
|
#define BCMA_PCI_BAR0_WIN2 0xAC
|
|
#define BCMA_PCI_GPIO_IN 0xB0 /* GPIO Input (pcirev >= 3 only) */
|
|
#define BCMA_PCI_GPIO_OUT 0xB4 /* GPIO Output (pcirev >= 3 only) */
|
|
#define BCMA_PCI_GPIO_OUT_ENABLE 0xB8 /* GPIO Output Enable/Disable (pcirev >= 3 only) */
|
|
#define BCMA_PCI_GPIO_SCS 0x10 /* PCI config space bit 4 for 4306c0 slow clock source */
|
|
#define BCMA_PCI_GPIO_HWRAD 0x20 /* PCI config space GPIO 13 for hw radio disable */
|
|
#define BCMA_PCI_GPIO_XTAL 0x40 /* PCI config space GPIO 14 for Xtal powerup */
|
|
#define BCMA_PCI_GPIO_PLL 0x80 /* PCI config space GPIO 15 for PLL powerdown */
|
|
|
|
/* SiliconBackplane Address Map.
|
|
* All regions may not exist on all chips.
|
|
*/
|
|
#define BCMA_SOC_SDRAM_BASE 0x00000000U /* Physical SDRAM */
|
|
#define BCMA_SOC_PCI_MEM 0x08000000U /* Host Mode sb2pcitranslation0 (64 MB) */
|
|
#define BCMA_SOC_PCI_MEM_SZ (64 * 1024 * 1024)
|
|
#define BCMA_SOC_PCI_CFG 0x0c000000U /* Host Mode sb2pcitranslation1 (64 MB) */
|
|
#define BCMA_SOC_SDRAM_SWAPPED 0x10000000U /* Byteswapped Physical SDRAM */
|
|
#define BCMA_SOC_SDRAM_R2 0x80000000U /* Region 2 for sdram (512 MB) */
|
|
|
|
|
|
#define BCMA_SOC_PCI_DMA 0x40000000U /* Client Mode sb2pcitranslation2 (1 GB) */
|
|
#define BCMA_SOC_PCI_DMA2 0x80000000U /* Client Mode sb2pcitranslation2 (1 GB) */
|
|
#define BCMA_SOC_PCI_DMA_SZ 0x40000000U /* Client Mode sb2pcitranslation2 size in bytes */
|
|
#define BCMA_SOC_PCIE_DMA_L32 0x00000000U /* PCIE Client Mode sb2pcitranslation2
|
|
* (2 ZettaBytes), low 32 bits
|
|
*/
|
|
#define BCMA_SOC_PCIE_DMA_H32 0x80000000U /* PCIE Client Mode sb2pcitranslation2
|
|
* (2 ZettaBytes), high 32 bits
|
|
*/
|
|
|
|
#define BCMA_SOC_PCI1_MEM 0x40000000U /* Host Mode sb2pcitranslation0 (64 MB) */
|
|
#define BCMA_SOC_PCI1_CFG 0x44000000U /* Host Mode sb2pcitranslation1 (64 MB) */
|
|
#define BCMA_SOC_PCIE1_DMA_H32 0xc0000000U /* PCIE Client Mode sb2pcitranslation2
|
|
* (2 ZettaBytes), high 32 bits
|
|
*/
|
|
|
|
#define BCMA_SOC_FLASH1 0x1fc00000 /* MIPS Flash Region 1 */
|
|
#define BCMA_SOC_FLASH1_SZ 0x00400000 /* MIPS Size of Flash Region 1 */
|
|
#define BCMA_SOC_FLASH2 0x1c000000 /* Flash Region 2 (region 1 shadowed here) */
|
|
#define BCMA_SOC_FLASH2_SZ 0x02000000 /* Size of Flash Region 2 */
|
|
|
|
#endif /* LINUX_BCMA_REGS_H_ */
|