![Ben Hutchings](/assets/img/avatar_default.png)
This driver has been mostly rewritten since Michael Brown's initial work, so swap the order of the authors. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
753 lines
20 KiB
C
753 lines
20 KiB
C
/****************************************************************************
|
|
* Driver for Solarflare Solarstorm network controllers and boards
|
|
* Copyright 2007-2009 Solarflare Communications Inc.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify it
|
|
* under the terms of the GNU General Public License version 2 as published
|
|
* by the Free Software Foundation, incorporated herein by reference.
|
|
*/
|
|
|
|
#include <linux/rtnetlink.h>
|
|
|
|
#include "net_driver.h"
|
|
#include "phy.h"
|
|
#include "efx.h"
|
|
#include "nic.h"
|
|
#include "regs.h"
|
|
#include "io.h"
|
|
#include "workarounds.h"
|
|
|
|
/* Macros for unpacking the board revision */
|
|
/* The revision info is in host byte order. */
|
|
#define FALCON_BOARD_TYPE(_rev) (_rev >> 8)
|
|
#define FALCON_BOARD_MAJOR(_rev) ((_rev >> 4) & 0xf)
|
|
#define FALCON_BOARD_MINOR(_rev) (_rev & 0xf)
|
|
|
|
/* Board types */
|
|
#define FALCON_BOARD_SFE4001 0x01
|
|
#define FALCON_BOARD_SFE4002 0x02
|
|
#define FALCON_BOARD_SFN4111T 0x51
|
|
#define FALCON_BOARD_SFN4112F 0x52
|
|
|
|
/*****************************************************************************
|
|
* Support for LM87 sensor chip used on several boards
|
|
*/
|
|
#define LM87_REG_ALARMS1 0x41
|
|
#define LM87_REG_ALARMS2 0x42
|
|
#define LM87_IN_LIMITS(nr, _min, _max) \
|
|
0x2B + (nr) * 2, _max, 0x2C + (nr) * 2, _min
|
|
#define LM87_AIN_LIMITS(nr, _min, _max) \
|
|
0x3B + (nr), _max, 0x1A + (nr), _min
|
|
#define LM87_TEMP_INT_LIMITS(_min, _max) \
|
|
0x39, _max, 0x3A, _min
|
|
#define LM87_TEMP_EXT1_LIMITS(_min, _max) \
|
|
0x37, _max, 0x38, _min
|
|
|
|
#define LM87_ALARM_TEMP_INT 0x10
|
|
#define LM87_ALARM_TEMP_EXT1 0x20
|
|
|
|
#if defined(CONFIG_SENSORS_LM87) || defined(CONFIG_SENSORS_LM87_MODULE)
|
|
|
|
static int efx_init_lm87(struct efx_nic *efx, struct i2c_board_info *info,
|
|
const u8 *reg_values)
|
|
{
|
|
struct falcon_board *board = falcon_board(efx);
|
|
struct i2c_client *client = i2c_new_device(&board->i2c_adap, info);
|
|
int rc;
|
|
|
|
if (!client)
|
|
return -EIO;
|
|
|
|
while (*reg_values) {
|
|
u8 reg = *reg_values++;
|
|
u8 value = *reg_values++;
|
|
rc = i2c_smbus_write_byte_data(client, reg, value);
|
|
if (rc)
|
|
goto err;
|
|
}
|
|
|
|
board->hwmon_client = client;
|
|
return 0;
|
|
|
|
err:
|
|
i2c_unregister_device(client);
|
|
return rc;
|
|
}
|
|
|
|
static void efx_fini_lm87(struct efx_nic *efx)
|
|
{
|
|
i2c_unregister_device(falcon_board(efx)->hwmon_client);
|
|
}
|
|
|
|
static int efx_check_lm87(struct efx_nic *efx, unsigned mask)
|
|
{
|
|
struct i2c_client *client = falcon_board(efx)->hwmon_client;
|
|
s32 alarms1, alarms2;
|
|
|
|
/* If link is up then do not monitor temperature */
|
|
if (EFX_WORKAROUND_7884(efx) && efx->link_state.up)
|
|
return 0;
|
|
|
|
alarms1 = i2c_smbus_read_byte_data(client, LM87_REG_ALARMS1);
|
|
alarms2 = i2c_smbus_read_byte_data(client, LM87_REG_ALARMS2);
|
|
if (alarms1 < 0)
|
|
return alarms1;
|
|
if (alarms2 < 0)
|
|
return alarms2;
|
|
alarms1 &= mask;
|
|
alarms2 &= mask >> 8;
|
|
if (alarms1 || alarms2) {
|
|
EFX_ERR(efx,
|
|
"LM87 detected a hardware failure (status %02x:%02x)"
|
|
"%s%s\n",
|
|
alarms1, alarms2,
|
|
(alarms1 & LM87_ALARM_TEMP_INT) ? " INTERNAL" : "",
|
|
(alarms1 & LM87_ALARM_TEMP_EXT1) ? " EXTERNAL" : "");
|
|
return -ERANGE;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
#else /* !CONFIG_SENSORS_LM87 */
|
|
|
|
static inline int
|
|
efx_init_lm87(struct efx_nic *efx, struct i2c_board_info *info,
|
|
const u8 *reg_values)
|
|
{
|
|
return 0;
|
|
}
|
|
static inline void efx_fini_lm87(struct efx_nic *efx)
|
|
{
|
|
}
|
|
static inline int efx_check_lm87(struct efx_nic *efx, unsigned mask)
|
|
{
|
|
return 0;
|
|
}
|
|
|
|
#endif /* CONFIG_SENSORS_LM87 */
|
|
|
|
/*****************************************************************************
|
|
* Support for the SFE4001 and SFN4111T NICs.
|
|
*
|
|
* The SFE4001 does not power-up fully at reset due to its high power
|
|
* consumption. We control its power via a PCA9539 I/O expander.
|
|
* Both boards have a MAX6647 temperature monitor which we expose to
|
|
* the lm90 driver.
|
|
*
|
|
* This also provides minimal support for reflashing the PHY, which is
|
|
* initiated by resetting it with the FLASH_CFG_1 pin pulled down.
|
|
* On SFE4001 rev A2 and later this is connected to the 3V3X output of
|
|
* the IO-expander; on the SFN4111T it is connected to Falcon's GPIO3.
|
|
* We represent reflash mode as PHY_MODE_SPECIAL and make it mutually
|
|
* exclusive with the network device being open.
|
|
*/
|
|
|
|
/**************************************************************************
|
|
* Support for I2C IO Expander device on SFE4001
|
|
*/
|
|
#define PCA9539 0x74
|
|
|
|
#define P0_IN 0x00
|
|
#define P0_OUT 0x02
|
|
#define P0_INVERT 0x04
|
|
#define P0_CONFIG 0x06
|
|
|
|
#define P0_EN_1V0X_LBN 0
|
|
#define P0_EN_1V0X_WIDTH 1
|
|
#define P0_EN_1V2_LBN 1
|
|
#define P0_EN_1V2_WIDTH 1
|
|
#define P0_EN_2V5_LBN 2
|
|
#define P0_EN_2V5_WIDTH 1
|
|
#define P0_EN_3V3X_LBN 3
|
|
#define P0_EN_3V3X_WIDTH 1
|
|
#define P0_EN_5V_LBN 4
|
|
#define P0_EN_5V_WIDTH 1
|
|
#define P0_SHORTEN_JTAG_LBN 5
|
|
#define P0_SHORTEN_JTAG_WIDTH 1
|
|
#define P0_X_TRST_LBN 6
|
|
#define P0_X_TRST_WIDTH 1
|
|
#define P0_DSP_RESET_LBN 7
|
|
#define P0_DSP_RESET_WIDTH 1
|
|
|
|
#define P1_IN 0x01
|
|
#define P1_OUT 0x03
|
|
#define P1_INVERT 0x05
|
|
#define P1_CONFIG 0x07
|
|
|
|
#define P1_AFE_PWD_LBN 0
|
|
#define P1_AFE_PWD_WIDTH 1
|
|
#define P1_DSP_PWD25_LBN 1
|
|
#define P1_DSP_PWD25_WIDTH 1
|
|
#define P1_RESERVED_LBN 2
|
|
#define P1_RESERVED_WIDTH 2
|
|
#define P1_SPARE_LBN 4
|
|
#define P1_SPARE_WIDTH 4
|
|
|
|
/* Temperature Sensor */
|
|
#define MAX664X_REG_RSL 0x02
|
|
#define MAX664X_REG_WLHO 0x0B
|
|
|
|
static void sfe4001_poweroff(struct efx_nic *efx)
|
|
{
|
|
struct i2c_client *ioexp_client = falcon_board(efx)->ioexp_client;
|
|
struct i2c_client *hwmon_client = falcon_board(efx)->hwmon_client;
|
|
|
|
/* Turn off all power rails and disable outputs */
|
|
i2c_smbus_write_byte_data(ioexp_client, P0_OUT, 0xff);
|
|
i2c_smbus_write_byte_data(ioexp_client, P1_CONFIG, 0xff);
|
|
i2c_smbus_write_byte_data(ioexp_client, P0_CONFIG, 0xff);
|
|
|
|
/* Clear any over-temperature alert */
|
|
i2c_smbus_read_byte_data(hwmon_client, MAX664X_REG_RSL);
|
|
}
|
|
|
|
static int sfe4001_poweron(struct efx_nic *efx)
|
|
{
|
|
struct i2c_client *ioexp_client = falcon_board(efx)->ioexp_client;
|
|
struct i2c_client *hwmon_client = falcon_board(efx)->hwmon_client;
|
|
unsigned int i, j;
|
|
int rc;
|
|
u8 out;
|
|
|
|
/* Clear any previous over-temperature alert */
|
|
rc = i2c_smbus_read_byte_data(hwmon_client, MAX664X_REG_RSL);
|
|
if (rc < 0)
|
|
return rc;
|
|
|
|
/* Enable port 0 and port 1 outputs on IO expander */
|
|
rc = i2c_smbus_write_byte_data(ioexp_client, P0_CONFIG, 0x00);
|
|
if (rc)
|
|
return rc;
|
|
rc = i2c_smbus_write_byte_data(ioexp_client, P1_CONFIG,
|
|
0xff & ~(1 << P1_SPARE_LBN));
|
|
if (rc)
|
|
goto fail_on;
|
|
|
|
/* If PHY power is on, turn it all off and wait 1 second to
|
|
* ensure a full reset.
|
|
*/
|
|
rc = i2c_smbus_read_byte_data(ioexp_client, P0_OUT);
|
|
if (rc < 0)
|
|
goto fail_on;
|
|
out = 0xff & ~((0 << P0_EN_1V2_LBN) | (0 << P0_EN_2V5_LBN) |
|
|
(0 << P0_EN_3V3X_LBN) | (0 << P0_EN_5V_LBN) |
|
|
(0 << P0_EN_1V0X_LBN));
|
|
if (rc != out) {
|
|
EFX_INFO(efx, "power-cycling PHY\n");
|
|
rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out);
|
|
if (rc)
|
|
goto fail_on;
|
|
schedule_timeout_uninterruptible(HZ);
|
|
}
|
|
|
|
for (i = 0; i < 20; ++i) {
|
|
/* Turn on 1.2V, 2.5V, 3.3V and 5V power rails */
|
|
out = 0xff & ~((1 << P0_EN_1V2_LBN) | (1 << P0_EN_2V5_LBN) |
|
|
(1 << P0_EN_3V3X_LBN) | (1 << P0_EN_5V_LBN) |
|
|
(1 << P0_X_TRST_LBN));
|
|
if (efx->phy_mode & PHY_MODE_SPECIAL)
|
|
out |= 1 << P0_EN_3V3X_LBN;
|
|
|
|
rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out);
|
|
if (rc)
|
|
goto fail_on;
|
|
msleep(10);
|
|
|
|
/* Turn on 1V power rail */
|
|
out &= ~(1 << P0_EN_1V0X_LBN);
|
|
rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out);
|
|
if (rc)
|
|
goto fail_on;
|
|
|
|
EFX_INFO(efx, "waiting for DSP boot (attempt %d)...\n", i);
|
|
|
|
/* In flash config mode, DSP does not turn on AFE, so
|
|
* just wait 1 second.
|
|
*/
|
|
if (efx->phy_mode & PHY_MODE_SPECIAL) {
|
|
schedule_timeout_uninterruptible(HZ);
|
|
return 0;
|
|
}
|
|
|
|
for (j = 0; j < 10; ++j) {
|
|
msleep(100);
|
|
|
|
/* Check DSP has asserted AFE power line */
|
|
rc = i2c_smbus_read_byte_data(ioexp_client, P1_IN);
|
|
if (rc < 0)
|
|
goto fail_on;
|
|
if (rc & (1 << P1_AFE_PWD_LBN))
|
|
return 0;
|
|
}
|
|
}
|
|
|
|
EFX_INFO(efx, "timed out waiting for DSP boot\n");
|
|
rc = -ETIMEDOUT;
|
|
fail_on:
|
|
sfe4001_poweroff(efx);
|
|
return rc;
|
|
}
|
|
|
|
static int sfn4111t_reset(struct efx_nic *efx)
|
|
{
|
|
struct falcon_board *board = falcon_board(efx);
|
|
efx_oword_t reg;
|
|
|
|
/* GPIO 3 and the GPIO register are shared with I2C, so block that */
|
|
i2c_lock_adapter(&board->i2c_adap);
|
|
|
|
/* Pull RST_N (GPIO 2) low then let it up again, setting the
|
|
* FLASH_CFG_1 strap (GPIO 3) appropriately. Only change the
|
|
* output enables; the output levels should always be 0 (low)
|
|
* and we rely on external pull-ups. */
|
|
efx_reado(efx, ®, FR_AB_GPIO_CTL);
|
|
EFX_SET_OWORD_FIELD(reg, FRF_AB_GPIO2_OEN, true);
|
|
efx_writeo(efx, ®, FR_AB_GPIO_CTL);
|
|
msleep(1000);
|
|
EFX_SET_OWORD_FIELD(reg, FRF_AB_GPIO2_OEN, false);
|
|
EFX_SET_OWORD_FIELD(reg, FRF_AB_GPIO3_OEN,
|
|
!!(efx->phy_mode & PHY_MODE_SPECIAL));
|
|
efx_writeo(efx, ®, FR_AB_GPIO_CTL);
|
|
msleep(1);
|
|
|
|
i2c_unlock_adapter(&board->i2c_adap);
|
|
|
|
ssleep(1);
|
|
return 0;
|
|
}
|
|
|
|
static ssize_t show_phy_flash_cfg(struct device *dev,
|
|
struct device_attribute *attr, char *buf)
|
|
{
|
|
struct efx_nic *efx = pci_get_drvdata(to_pci_dev(dev));
|
|
return sprintf(buf, "%d\n", !!(efx->phy_mode & PHY_MODE_SPECIAL));
|
|
}
|
|
|
|
static ssize_t set_phy_flash_cfg(struct device *dev,
|
|
struct device_attribute *attr,
|
|
const char *buf, size_t count)
|
|
{
|
|
struct efx_nic *efx = pci_get_drvdata(to_pci_dev(dev));
|
|
enum efx_phy_mode old_mode, new_mode;
|
|
int err;
|
|
|
|
rtnl_lock();
|
|
old_mode = efx->phy_mode;
|
|
if (count == 0 || *buf == '0')
|
|
new_mode = old_mode & ~PHY_MODE_SPECIAL;
|
|
else
|
|
new_mode = PHY_MODE_SPECIAL;
|
|
if (old_mode == new_mode) {
|
|
err = 0;
|
|
} else if (efx->state != STATE_RUNNING || netif_running(efx->net_dev)) {
|
|
err = -EBUSY;
|
|
} else {
|
|
/* Reset the PHY, reconfigure the MAC and enable/disable
|
|
* MAC stats accordingly. */
|
|
efx->phy_mode = new_mode;
|
|
if (new_mode & PHY_MODE_SPECIAL)
|
|
falcon_stop_nic_stats(efx);
|
|
if (falcon_board(efx)->type->id == FALCON_BOARD_SFE4001)
|
|
err = sfe4001_poweron(efx);
|
|
else
|
|
err = sfn4111t_reset(efx);
|
|
if (!err)
|
|
err = efx_reconfigure_port(efx);
|
|
if (!(new_mode & PHY_MODE_SPECIAL))
|
|
falcon_start_nic_stats(efx);
|
|
}
|
|
rtnl_unlock();
|
|
|
|
return err ? err : count;
|
|
}
|
|
|
|
static DEVICE_ATTR(phy_flash_cfg, 0644, show_phy_flash_cfg, set_phy_flash_cfg);
|
|
|
|
static void sfe4001_fini(struct efx_nic *efx)
|
|
{
|
|
struct falcon_board *board = falcon_board(efx);
|
|
|
|
EFX_INFO(efx, "%s\n", __func__);
|
|
|
|
device_remove_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg);
|
|
sfe4001_poweroff(efx);
|
|
i2c_unregister_device(board->ioexp_client);
|
|
i2c_unregister_device(board->hwmon_client);
|
|
}
|
|
|
|
static int sfe4001_check_hw(struct efx_nic *efx)
|
|
{
|
|
s32 status;
|
|
|
|
/* If XAUI link is up then do not monitor */
|
|
if (EFX_WORKAROUND_7884(efx) && !efx->xmac_poll_required)
|
|
return 0;
|
|
|
|
/* Check the powered status of the PHY. Lack of power implies that
|
|
* the MAX6647 has shut down power to it, probably due to a temp.
|
|
* alarm. Reading the power status rather than the MAX6647 status
|
|
* directly because the later is read-to-clear and would thus
|
|
* start to power up the PHY again when polled, causing us to blip
|
|
* the power undesirably.
|
|
* We know we can read from the IO expander because we did
|
|
* it during power-on. Assume failure now is bad news. */
|
|
status = i2c_smbus_read_byte_data(falcon_board(efx)->ioexp_client, P1_IN);
|
|
if (status >= 0 &&
|
|
(status & ((1 << P1_AFE_PWD_LBN) | (1 << P1_DSP_PWD25_LBN))) != 0)
|
|
return 0;
|
|
|
|
/* Use board power control, not PHY power control */
|
|
sfe4001_poweroff(efx);
|
|
efx->phy_mode = PHY_MODE_OFF;
|
|
|
|
return (status < 0) ? -EIO : -ERANGE;
|
|
}
|
|
|
|
static struct i2c_board_info sfe4001_hwmon_info = {
|
|
I2C_BOARD_INFO("max6647", 0x4e),
|
|
};
|
|
|
|
/* This board uses an I2C expander to provider power to the PHY, which needs to
|
|
* be turned on before the PHY can be used.
|
|
* Context: Process context, rtnl lock held
|
|
*/
|
|
static int sfe4001_init(struct efx_nic *efx)
|
|
{
|
|
struct falcon_board *board = falcon_board(efx);
|
|
int rc;
|
|
|
|
#if defined(CONFIG_SENSORS_LM90) || defined(CONFIG_SENSORS_LM90_MODULE)
|
|
board->hwmon_client =
|
|
i2c_new_device(&board->i2c_adap, &sfe4001_hwmon_info);
|
|
#else
|
|
board->hwmon_client =
|
|
i2c_new_dummy(&board->i2c_adap, sfe4001_hwmon_info.addr);
|
|
#endif
|
|
if (!board->hwmon_client)
|
|
return -EIO;
|
|
|
|
/* Raise board/PHY high limit from 85 to 90 degrees Celsius */
|
|
rc = i2c_smbus_write_byte_data(board->hwmon_client,
|
|
MAX664X_REG_WLHO, 90);
|
|
if (rc)
|
|
goto fail_hwmon;
|
|
|
|
board->ioexp_client = i2c_new_dummy(&board->i2c_adap, PCA9539);
|
|
if (!board->ioexp_client) {
|
|
rc = -EIO;
|
|
goto fail_hwmon;
|
|
}
|
|
|
|
if (efx->phy_mode & PHY_MODE_SPECIAL) {
|
|
/* PHY won't generate a 156.25 MHz clock and MAC stats fetch
|
|
* will fail. */
|
|
falcon_stop_nic_stats(efx);
|
|
}
|
|
rc = sfe4001_poweron(efx);
|
|
if (rc)
|
|
goto fail_ioexp;
|
|
|
|
rc = device_create_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg);
|
|
if (rc)
|
|
goto fail_on;
|
|
|
|
EFX_INFO(efx, "PHY is powered on\n");
|
|
return 0;
|
|
|
|
fail_on:
|
|
sfe4001_poweroff(efx);
|
|
fail_ioexp:
|
|
i2c_unregister_device(board->ioexp_client);
|
|
fail_hwmon:
|
|
i2c_unregister_device(board->hwmon_client);
|
|
return rc;
|
|
}
|
|
|
|
static int sfn4111t_check_hw(struct efx_nic *efx)
|
|
{
|
|
s32 status;
|
|
|
|
/* If XAUI link is up then do not monitor */
|
|
if (EFX_WORKAROUND_7884(efx) && !efx->xmac_poll_required)
|
|
return 0;
|
|
|
|
/* Test LHIGH, RHIGH, FAULT, EOT and IOT alarms */
|
|
status = i2c_smbus_read_byte_data(falcon_board(efx)->hwmon_client,
|
|
MAX664X_REG_RSL);
|
|
if (status < 0)
|
|
return -EIO;
|
|
if (status & 0x57)
|
|
return -ERANGE;
|
|
return 0;
|
|
}
|
|
|
|
static void sfn4111t_fini(struct efx_nic *efx)
|
|
{
|
|
EFX_INFO(efx, "%s\n", __func__);
|
|
|
|
device_remove_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg);
|
|
i2c_unregister_device(falcon_board(efx)->hwmon_client);
|
|
}
|
|
|
|
static struct i2c_board_info sfn4111t_a0_hwmon_info = {
|
|
I2C_BOARD_INFO("max6647", 0x4e),
|
|
};
|
|
|
|
static struct i2c_board_info sfn4111t_r5_hwmon_info = {
|
|
I2C_BOARD_INFO("max6646", 0x4d),
|
|
};
|
|
|
|
static void sfn4111t_init_phy(struct efx_nic *efx)
|
|
{
|
|
if (!(efx->phy_mode & PHY_MODE_SPECIAL)) {
|
|
if (sft9001_wait_boot(efx) != -EINVAL)
|
|
return;
|
|
|
|
efx->phy_mode = PHY_MODE_SPECIAL;
|
|
falcon_stop_nic_stats(efx);
|
|
}
|
|
|
|
sfn4111t_reset(efx);
|
|
sft9001_wait_boot(efx);
|
|
}
|
|
|
|
static int sfn4111t_init(struct efx_nic *efx)
|
|
{
|
|
struct falcon_board *board = falcon_board(efx);
|
|
int rc;
|
|
|
|
board->hwmon_client =
|
|
i2c_new_device(&board->i2c_adap,
|
|
(board->minor < 5) ?
|
|
&sfn4111t_a0_hwmon_info :
|
|
&sfn4111t_r5_hwmon_info);
|
|
if (!board->hwmon_client)
|
|
return -EIO;
|
|
|
|
rc = device_create_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg);
|
|
if (rc)
|
|
goto fail_hwmon;
|
|
|
|
if (efx->phy_mode & PHY_MODE_SPECIAL)
|
|
/* PHY may not generate a 156.25 MHz clock and MAC
|
|
* stats fetch will fail. */
|
|
falcon_stop_nic_stats(efx);
|
|
|
|
return 0;
|
|
|
|
fail_hwmon:
|
|
i2c_unregister_device(board->hwmon_client);
|
|
return rc;
|
|
}
|
|
|
|
/*****************************************************************************
|
|
* Support for the SFE4002
|
|
*
|
|
*/
|
|
static u8 sfe4002_lm87_channel = 0x03; /* use AIN not FAN inputs */
|
|
|
|
static const u8 sfe4002_lm87_regs[] = {
|
|
LM87_IN_LIMITS(0, 0x83, 0x91), /* 2.5V: 1.8V +/- 5% */
|
|
LM87_IN_LIMITS(1, 0x51, 0x5a), /* Vccp1: 1.2V +/- 5% */
|
|
LM87_IN_LIMITS(2, 0xb6, 0xca), /* 3.3V: 3.3V +/- 5% */
|
|
LM87_IN_LIMITS(3, 0xb0, 0xc9), /* 5V: 4.6-5.2V */
|
|
LM87_IN_LIMITS(4, 0xb0, 0xe0), /* 12V: 11-14V */
|
|
LM87_IN_LIMITS(5, 0x44, 0x4b), /* Vccp2: 1.0V +/- 5% */
|
|
LM87_AIN_LIMITS(0, 0xa0, 0xb2), /* AIN1: 1.66V +/- 5% */
|
|
LM87_AIN_LIMITS(1, 0x91, 0xa1), /* AIN2: 1.5V +/- 5% */
|
|
LM87_TEMP_INT_LIMITS(10, 60), /* board */
|
|
LM87_TEMP_EXT1_LIMITS(10, 70), /* Falcon */
|
|
0
|
|
};
|
|
|
|
static struct i2c_board_info sfe4002_hwmon_info = {
|
|
I2C_BOARD_INFO("lm87", 0x2e),
|
|
.platform_data = &sfe4002_lm87_channel,
|
|
};
|
|
|
|
/****************************************************************************/
|
|
/* LED allocations. Note that on rev A0 boards the schematic and the reality
|
|
* differ: red and green are swapped. Below is the fixed (A1) layout (there
|
|
* are only 3 A0 boards in existence, so no real reason to make this
|
|
* conditional).
|
|
*/
|
|
#define SFE4002_FAULT_LED (2) /* Red */
|
|
#define SFE4002_RX_LED (0) /* Green */
|
|
#define SFE4002_TX_LED (1) /* Amber */
|
|
|
|
static void sfe4002_init_phy(struct efx_nic *efx)
|
|
{
|
|
/* Set the TX and RX LEDs to reflect status and activity, and the
|
|
* fault LED off */
|
|
falcon_qt202x_set_led(efx, SFE4002_TX_LED,
|
|
QUAKE_LED_TXLINK | QUAKE_LED_LINK_ACTSTAT);
|
|
falcon_qt202x_set_led(efx, SFE4002_RX_LED,
|
|
QUAKE_LED_RXLINK | QUAKE_LED_LINK_ACTSTAT);
|
|
falcon_qt202x_set_led(efx, SFE4002_FAULT_LED, QUAKE_LED_OFF);
|
|
}
|
|
|
|
static void sfe4002_set_id_led(struct efx_nic *efx, enum efx_led_mode mode)
|
|
{
|
|
falcon_qt202x_set_led(
|
|
efx, SFE4002_FAULT_LED,
|
|
(mode == EFX_LED_ON) ? QUAKE_LED_ON : QUAKE_LED_OFF);
|
|
}
|
|
|
|
static int sfe4002_check_hw(struct efx_nic *efx)
|
|
{
|
|
struct falcon_board *board = falcon_board(efx);
|
|
|
|
/* A0 board rev. 4002s report a temperature fault the whole time
|
|
* (bad sensor) so we mask it out. */
|
|
unsigned alarm_mask =
|
|
(board->major == 0 && board->minor == 0) ?
|
|
~LM87_ALARM_TEMP_EXT1 : ~0;
|
|
|
|
return efx_check_lm87(efx, alarm_mask);
|
|
}
|
|
|
|
static int sfe4002_init(struct efx_nic *efx)
|
|
{
|
|
return efx_init_lm87(efx, &sfe4002_hwmon_info, sfe4002_lm87_regs);
|
|
}
|
|
|
|
/*****************************************************************************
|
|
* Support for the SFN4112F
|
|
*
|
|
*/
|
|
static u8 sfn4112f_lm87_channel = 0x03; /* use AIN not FAN inputs */
|
|
|
|
static const u8 sfn4112f_lm87_regs[] = {
|
|
LM87_IN_LIMITS(0, 0x83, 0x91), /* 2.5V: 1.8V +/- 5% */
|
|
LM87_IN_LIMITS(1, 0x51, 0x5a), /* Vccp1: 1.2V +/- 5% */
|
|
LM87_IN_LIMITS(2, 0xb6, 0xca), /* 3.3V: 3.3V +/- 5% */
|
|
LM87_IN_LIMITS(4, 0xb0, 0xe0), /* 12V: 11-14V */
|
|
LM87_IN_LIMITS(5, 0x44, 0x4b), /* Vccp2: 1.0V +/- 5% */
|
|
LM87_AIN_LIMITS(1, 0x91, 0xa1), /* AIN2: 1.5V +/- 5% */
|
|
LM87_TEMP_INT_LIMITS(10, 60), /* board */
|
|
LM87_TEMP_EXT1_LIMITS(10, 70), /* Falcon */
|
|
0
|
|
};
|
|
|
|
static struct i2c_board_info sfn4112f_hwmon_info = {
|
|
I2C_BOARD_INFO("lm87", 0x2e),
|
|
.platform_data = &sfn4112f_lm87_channel,
|
|
};
|
|
|
|
#define SFN4112F_ACT_LED 0
|
|
#define SFN4112F_LINK_LED 1
|
|
|
|
static void sfn4112f_init_phy(struct efx_nic *efx)
|
|
{
|
|
falcon_qt202x_set_led(efx, SFN4112F_ACT_LED,
|
|
QUAKE_LED_RXLINK | QUAKE_LED_LINK_ACT);
|
|
falcon_qt202x_set_led(efx, SFN4112F_LINK_LED,
|
|
QUAKE_LED_RXLINK | QUAKE_LED_LINK_STAT);
|
|
}
|
|
|
|
static void sfn4112f_set_id_led(struct efx_nic *efx, enum efx_led_mode mode)
|
|
{
|
|
int reg;
|
|
|
|
switch (mode) {
|
|
case EFX_LED_OFF:
|
|
reg = QUAKE_LED_OFF;
|
|
break;
|
|
case EFX_LED_ON:
|
|
reg = QUAKE_LED_ON;
|
|
break;
|
|
default:
|
|
reg = QUAKE_LED_RXLINK | QUAKE_LED_LINK_STAT;
|
|
break;
|
|
}
|
|
|
|
falcon_qt202x_set_led(efx, SFN4112F_LINK_LED, reg);
|
|
}
|
|
|
|
static int sfn4112f_check_hw(struct efx_nic *efx)
|
|
{
|
|
/* Mask out unused sensors */
|
|
return efx_check_lm87(efx, ~0x48);
|
|
}
|
|
|
|
static int sfn4112f_init(struct efx_nic *efx)
|
|
{
|
|
return efx_init_lm87(efx, &sfn4112f_hwmon_info, sfn4112f_lm87_regs);
|
|
}
|
|
|
|
static const struct falcon_board_type board_types[] = {
|
|
{
|
|
.id = FALCON_BOARD_SFE4001,
|
|
.ref_model = "SFE4001",
|
|
.gen_type = "10GBASE-T adapter",
|
|
.init = sfe4001_init,
|
|
.init_phy = efx_port_dummy_op_void,
|
|
.fini = sfe4001_fini,
|
|
.set_id_led = tenxpress_set_id_led,
|
|
.monitor = sfe4001_check_hw,
|
|
},
|
|
{
|
|
.id = FALCON_BOARD_SFE4002,
|
|
.ref_model = "SFE4002",
|
|
.gen_type = "XFP adapter",
|
|
.init = sfe4002_init,
|
|
.init_phy = sfe4002_init_phy,
|
|
.fini = efx_fini_lm87,
|
|
.set_id_led = sfe4002_set_id_led,
|
|
.monitor = sfe4002_check_hw,
|
|
},
|
|
{
|
|
.id = FALCON_BOARD_SFN4111T,
|
|
.ref_model = "SFN4111T",
|
|
.gen_type = "100/1000/10GBASE-T adapter",
|
|
.init = sfn4111t_init,
|
|
.init_phy = sfn4111t_init_phy,
|
|
.fini = sfn4111t_fini,
|
|
.set_id_led = tenxpress_set_id_led,
|
|
.monitor = sfn4111t_check_hw,
|
|
},
|
|
{
|
|
.id = FALCON_BOARD_SFN4112F,
|
|
.ref_model = "SFN4112F",
|
|
.gen_type = "SFP+ adapter",
|
|
.init = sfn4112f_init,
|
|
.init_phy = sfn4112f_init_phy,
|
|
.fini = efx_fini_lm87,
|
|
.set_id_led = sfn4112f_set_id_led,
|
|
.monitor = sfn4112f_check_hw,
|
|
},
|
|
};
|
|
|
|
static const struct falcon_board_type falcon_dummy_board = {
|
|
.init = efx_port_dummy_op_int,
|
|
.init_phy = efx_port_dummy_op_void,
|
|
.fini = efx_port_dummy_op_void,
|
|
.set_id_led = efx_port_dummy_op_set_id_led,
|
|
.monitor = efx_port_dummy_op_int,
|
|
};
|
|
|
|
void falcon_probe_board(struct efx_nic *efx, u16 revision_info)
|
|
{
|
|
struct falcon_board *board = falcon_board(efx);
|
|
u8 type_id = FALCON_BOARD_TYPE(revision_info);
|
|
int i;
|
|
|
|
board->major = FALCON_BOARD_MAJOR(revision_info);
|
|
board->minor = FALCON_BOARD_MINOR(revision_info);
|
|
|
|
for (i = 0; i < ARRAY_SIZE(board_types); i++)
|
|
if (board_types[i].id == type_id)
|
|
board->type = &board_types[i];
|
|
|
|
if (board->type) {
|
|
EFX_INFO(efx, "board is %s rev %c%d\n",
|
|
(efx->pci_dev->subsystem_vendor == EFX_VENDID_SFC)
|
|
? board->type->ref_model : board->type->gen_type,
|
|
'A' + board->major, board->minor);
|
|
} else {
|
|
EFX_ERR(efx, "unknown board type %d\n", type_id);
|
|
board->type = &falcon_dummy_board;
|
|
}
|
|
}
|