diff --git a/board/sheldon/simpc8313/Makefile b/board/sheldon/simpc8313/Makefile deleted file mode 100644 index a824c41d9c..0000000000 --- a/board/sheldon/simpc8313/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# (C) Copyright 2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := simpc8313.o sdram.o diff --git a/board/sheldon/simpc8313/README.simpc8313 b/board/sheldon/simpc8313/README.simpc8313 deleted file mode 100644 index b362c6aeea..0000000000 --- a/board/sheldon/simpc8313/README.simpc8313 +++ /dev/null @@ -1,80 +0,0 @@ -Sheldon Instruments SIMPC8313 Board ------------------------------------------ - -1. Board Switches and Jumpers - - S2 is used to set CFG_RESET_SOURCE. - - To boot the image in Large page NAND flash, use these DIP - switch settings for S2: - - +----------+ ON - | * * **** | - | * * | - +----------+ - 12345678 - - To boot the image in Small page NAND flash, use these DIP - switch settings for S2: - - +----------+ ON - | *** **** | - | * | - +----------+ - 12345678 - (where the '*' indicates the position of the tab of the switch.) - -2. Memory Map - The memory map looks like this: - - 0x0000_0000 0x1fff_ffff DDR 512M - 0x8000_0000 0x8fff_ffff PCI MEM 256M - 0x9000_0000 0x9fff_ffff PCI_MMIO 256M - 0xe000_0000 0xe00f_ffff IMMR 1M - 0xe200_0000 0xe20f_ffff PCI IO 16M - 0xe280_0000 0xe280_7fff NAND FLASH (CS0) 32K - or - 0xe280_0000 0xe281_ffff NAND FLASH (CS0) 128K - 0xff00_0000 0xff00_7fff FPGA (CS1) 1M - -3. Compilation - - Assuming you're using BASH (or similar) as your shell: - - export CROSS_COMPILE=your-cross-compiler-prefix- - make distclean - make SIMPC8313_LP_config - (or make SIMPC8313_SP_config, depending on the page size - of your NAND flash) - make - -4. Downloading and Flashing Images - -4.1 Reflash U-boot Image using U-boot - - =>run update_uboot - - You may want to try - =>tftp $loadaddr $uboot - first, to make sure that the TFTP load will succeed before it - goes ahead and wipes out your current firmware. And of course, - if the new u-boot doesn't boot, you can plug the board into - your PCI slot and with the supplied driver and sample app - you can reburn a working u-boot. - -4.2 Downloading and Booting Linux Kernel - - Ensure that all networking-related environment variables are set - properly (including ipaddr, serverip, gatewayip (if needed), - netmask, ethaddr, eth1addr, fdtfile, and bootfile). - - =>tftp $loadaddr uImage - =>nand write $loadaddr kernel $filesize - =>tftp $loadaddr $fdtfile - =>nand write $loadaddr 7e0000 1800 - - =>boot - -5 Notes - - The console baudrate for SIMPC8313 is 115200bps. diff --git a/board/sheldon/simpc8313/sdram.c b/board/sheldon/simpc8313/sdram.c deleted file mode 100644 index 7c12fe851c..0000000000 --- a/board/sheldon/simpc8313/sdram.c +++ /dev/null @@ -1,177 +0,0 @@ -/* - * Copyright (C) Freescale Semiconductor, Inc. 2006-2007 - * Copyright (C) Sheldon Instruments, Inc. 2008 - * - * Author: Ron Madrid - * - * (C) Copyright 2006 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include -#include -#include - -DECLARE_GLOBAL_DATA_PTR; - -static long fixed_sdram(void); - -#if defined(CONFIG_NAND_SPL) -void si_wait_i2c(void) -{ - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; - - while (!(__raw_readb(&im->i2c[0].sr) & 0x02)) - ; - - __raw_writeb(0x00, &im->i2c[0].sr); - - sync(); - - return; -} - -void si_read_i2c(u32 lbyte, int count, u8 *buffer) -{ - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; - u32 i; - u8 chip = 0x50 << 1; /* boot sequencer I2C */ - u32 ubyte = (lbyte & 0xff00) >> 8; - - lbyte &= 0xff; - - /* - * Set up controller - */ - __raw_writeb(0x3f, &im->i2c[0].fdr); - __raw_writeb(0x00, &im->i2c[0].adr); - __raw_writeb(0x00, &im->i2c[0].sr); - __raw_writeb(0x00, &im->i2c[0].dr); - - while (__raw_readb(&im->i2c[0].sr) & 0x20) - ; - - /* - * Writing address to device - */ - __raw_writeb(0xb0, &im->i2c[0].cr); - sync(); - __raw_writeb(chip, &im->i2c[0].dr); - si_wait_i2c(); - - __raw_writeb(0xb0, &im->i2c[0].cr); - sync(); - __raw_writeb(ubyte, &im->i2c[0].dr); - si_wait_i2c(); - - __raw_writeb(lbyte, &im->i2c[0].dr); - si_wait_i2c(); - - __raw_writeb(0xb4, &im->i2c[0].cr); - sync(); - __raw_writeb(chip + 1, &im->i2c[0].dr); - si_wait_i2c(); - - __raw_writeb(0xa0, &im->i2c[0].cr); - sync(); - - /* - * Dummy read - */ - __raw_readb(&im->i2c[0].dr); - - si_wait_i2c(); - - /* - * Read actual data - */ - for (i = 0; i < count; i++) - { - if (i == (count - 2)) /* Reached next to last byte, No ACK */ - __raw_writeb(0xa8, &im->i2c[0].cr); - if (i == (count - 1)) /* Reached last byte, STOP */ - __raw_writeb(0x88, &im->i2c[0].cr); - - /* Read byte of data */ - buffer[i] = __raw_readb(&im->i2c[0].dr); - - if (i == (count - 1)) - break; - si_wait_i2c(); - } - - return; -} -#endif /* CONFIG_NAND_SPL */ - -phys_size_t initdram(int board_type) -{ - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; - volatile fsl_lbc_t *lbc = &im->im_lbc; - u32 msize; - - if ((__raw_readl(&im->sysconf.immrbar) & IMMRBAR_BASE_ADDR) != (u32) im) - return -1; - - /* DDR SDRAM - Main SODIMM */ - __raw_writel(CONFIG_SYS_DDR_BASE & LAWBAR_BAR, &im->sysconf.ddrlaw[0].bar); - - msize = fixed_sdram(); - - /* Local Bus setup lbcr and mrtpr */ - __raw_writel(CONFIG_SYS_LBC_LBCR, &lbc->lbcr); - __raw_writel(CONFIG_SYS_LBC_MRTPR, &lbc->mrtpr); - sync(); - - /* return total bus SDRAM size(bytes) -- DDR */ - return (msize * 1024 * 1024); -} - -/************************************************************************* - * fixed sdram init -- reads values from boot sequencer I2C - ************************************************************************/ -static long fixed_sdram(void) -{ - volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR; - u32 msizelog2, msize = 1; -#if defined(CONFIG_NAND_SPL) - u32 i; - const u8 bytecount = 135; - u8 buffer[bytecount]; - u32 addr, data; - - si_read_i2c(0, bytecount, buffer); - - for (i = 18; i < bytecount; i += 7){ - addr = (u32)buffer[i]; - addr <<= 8; - addr |= (u32)buffer[i + 1]; - addr <<= 2; - data = (u32)buffer[i + 2]; - data <<= 8; - data |= (u32)buffer[i + 3]; - data <<= 8; - data |= (u32)buffer[i + 4]; - data <<= 8; - data |= (u32)buffer[i + 5]; - - __raw_writel(data, (u32 *)(CONFIG_SYS_IMMR + addr)); - } - - sync(); - - /* enable DDR controller */ - __raw_writel((__raw_readl(&im->ddr.sdram_cfg) | SDRAM_CFG_MEM_EN), &im->ddr.sdram_cfg); -#endif /* (CONFIG_NAND_SPL) */ - - msizelog2 = ((__raw_readl(&im->sysconf.ddrlaw[0].ar) & LAWAR_SIZE) + 1); - msize <<= (msizelog2 - 20); - - return msize; -} diff --git a/board/sheldon/simpc8313/simpc8313.c b/board/sheldon/simpc8313/simpc8313.c deleted file mode 100644 index 31406fa66d..0000000000 --- a/board/sheldon/simpc8313/simpc8313.c +++ /dev/null @@ -1,150 +0,0 @@ -/* - * Copyright (C) Freescale Semiconductor, Inc. 2006-2007 - * Copyright (C) Sheldon Instruments, Inc. 2008 - * - * Author: Ron Madrid - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include -#include -#include - -DECLARE_GLOBAL_DATA_PTR; - -#ifndef CONFIG_NAND_SPL -int checkboard(void) -{ - puts("Board: Sheldon Instruments SIMPC8313\n"); - return 0; -} - -static struct pci_region pci_regions[] = { - { - bus_start: CONFIG_SYS_PCI1_MEM_BASE, - phys_start: CONFIG_SYS_PCI1_MEM_PHYS, - size: CONFIG_SYS_PCI1_MEM_SIZE, - flags: PCI_REGION_MEM | PCI_REGION_PREFETCH - }, - { - bus_start: CONFIG_SYS_PCI1_MMIO_BASE, - phys_start: CONFIG_SYS_PCI1_MMIO_PHYS, - size: CONFIG_SYS_PCI1_MMIO_SIZE, - flags: PCI_REGION_MEM - }, - { - bus_start: CONFIG_SYS_PCI1_IO_BASE, - phys_start: CONFIG_SYS_PCI1_IO_PHYS, - size: CONFIG_SYS_PCI1_IO_SIZE, - flags: PCI_REGION_IO - } -}; - -void pci_init_board(void) -{ - volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR; - volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk; - volatile law83xx_t *pci_law = immr->sysconf.pcilaw; - struct pci_region *reg[] = { pci_regions }; - - /* Enable all 3 PCI_CLK_OUTPUTs. */ - clk->occr |= 0xe0000000; - - /* - * Configure PCI Local Access Windows - */ - pci_law[0].bar = CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR; - pci_law[0].ar = LBLAWAR_EN | LBLAWAR_512MB; - - pci_law[1].bar = CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR; - pci_law[1].ar = LBLAWAR_EN | LBLAWAR_1MB; - - mpc83xx_pci_init(1, reg); -} - -/* - * Miscellaneous late-boot configurations - */ -int misc_init_r(void) -{ - int rc = 0; - immap_t *immap = (immap_t *) CONFIG_SYS_IMMR; - fsl_lbc_t *lbus = &immap->im_lbc; - u32 *mxmr = &lbus->mamr; /* Pointer to mamr */ - - /* UPM Table Configuration Code */ - static uint UPMATable[] = { - /* Read Single-Beat (RSS) */ - 0x0fff0c00, 0x0fffdc00, 0x0fff0c05, 0xfffffc00, - 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01, - /* Read Burst (RBS) */ - 0x0fff0c00, 0x0ffcdc00, 0x0ffc0c00, 0x0ffc0f0c, - 0x0ffccf0c, 0x0ffc0f0c, 0x0ffcce0c, 0x3ffc0c05, - 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, - 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01, - /* Write Single-Beat (WSS) */ - 0x0ffc0c00, 0x0ffcdc00, 0x0ffc0c05, 0xfffffc00, - 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01, - /* Write Burst (WBS) */ - 0x0ffc0c00, 0x0fffcc0c, 0x0fff0c00, 0x0fffcc00, - 0x0fff1c00, 0x0fffcf0c, 0x0fff0f0c, 0x0fffcf0c, - 0x0fff0c0c, 0x0fffcc0c, 0x0fff0c05, 0xfffffc00, - 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01, - /* Refresh Timer (RTS) */ - 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, - 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc00, - 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01, - /* Exception Condition (EXS) */ - 0xfffffc00, 0xfffffc00, 0xfffffc00, 0xfffffc01 - }; - - upmconfig(UPMA, UPMATable, sizeof(UPMATable) / sizeof(UPMATable[0])); - - /* Set LUPWAIT to be active low and enabled */ - out_be32(mxmr, MxMR_UWPL | MxMR_GPL_x4DIS); - - return rc; -} - -#if defined(CONFIG_OF_BOARD_SETUP) -void ft_board_setup(void *blob, bd_t *bd) -{ - ft_cpu_setup(blob, bd); -#ifdef CONFIG_PCI - ft_pci_setup(blob, bd); -#endif -} -#endif -#else /* CONFIG_NAND_SPL */ -void board_init_f(ulong bootflag) -{ - NS16550_init((NS16550_t)(CONFIG_SYS_IMMR + 0x4500), - CONFIG_SYS_NS16550_CLK / 16 / CONFIG_BAUDRATE); - puts("NAND boot... "); - init_timebase(); - initdram(0); - relocate_code(CONFIG_SYS_NAND_U_BOOT_RELOC_SP, (gd_t *)gd, - CONFIG_SYS_NAND_U_BOOT_RELOC); -} - -void board_init_r(gd_t *gd, ulong dest_addr) -{ - nand_boot(); -} - -void putc(char c) -{ - if (gd->flags & GD_FLG_SILENT) - return; - - if (c == '\n') - NS16550_putc((NS16550_t)(CONFIG_SYS_IMMR + 0x4500), '\r'); - - NS16550_putc((NS16550_t)(CONFIG_SYS_IMMR + 0x4500), c); -} -#endif diff --git a/boards.cfg b/boards.cfg index d8646c622a..a58efd6864 100644 --- a/boards.cfg +++ b/boards.cfg @@ -717,8 +717,6 @@ Active powerpc mpc83xx - keymile km83xx Active powerpc mpc83xx - keymile km83xx suvd3 suvd3:SUVD3 Holger Brunck Active powerpc mpc83xx - keymile km83xx tuge1 tuxx1:TUGE1 Holger Brunck Active powerpc mpc83xx - keymile km83xx tuxx1 tuxx1:TUXX1 Holger Brunck -Active powerpc mpc83xx - sheldon simpc8313 SIMPC8313_LP SIMPC8313:NAND_LP Ron Madrid -Active powerpc mpc83xx - sheldon simpc8313 SIMPC8313_SP SIMPC8313:NAND_SP Ron Madrid Active powerpc mpc83xx - tqc tqm834x TQM834x - - Active powerpc mpc85xx - - sbc8548 sbc8548 - Paul Gortmaker Active powerpc mpc85xx - - sbc8548 sbc8548_PCI_33 sbc8548:PCI,33 Paul Gortmaker diff --git a/doc/README.scrapyard b/doc/README.scrapyard index e2157e08be..6c6be68c5a 100644 --- a/doc/README.scrapyard +++ b/doc/README.scrapyard @@ -11,16 +11,17 @@ easily if here is something they might want to dig for... Board Arch CPU Commit Removed Last known maintainer/contact ================================================================================================= -hidden_dragon powerpc mpc824x - - Yusdi Santoso -debris powerpc mpc824x - - Sangmoon Kim -kvme080 powerpc mpc824x - - Sangmoon Kim -ep8248 powerpc mpc8260 - - Yuli Barcohen -ispan powerpc mpc8260 - - Yuli Barcohen -rattler powerpc mpc8260 - - Yuli Barcohen -zpc1900 powerpc mpc8260 - - Yuli Barcohen -mpc8260ads powerpc mpc8260 - - Yuli Barcohen -adder powerpc mpc8xx - - Yuli Barcohen -quad100hd powerpc ppc405ep - - Gary Jennejohn +simpc8313 powerpc mpc83xx - 2014-04-28 Ron Madrid +hidden_dragon powerpc mpc824x 3fe1a854 2014-05-30 Yusdi Santoso +debris powerpc mpc824x 7edb1f7b 2014-05-30 Sangmoon Kim +kvme080 powerpc mpc824x 2868f862 2014-05-30 Sangmoon Kim +ep8248 powerpc mpc8260 49ad566d 2014-05-30 Yuli Barcohen +ispan powerpc mpc8260 80bae39a 2014-05-30 Yuli Barcohen +rattler powerpc mpc8260 d0664db4 2014-05-30 Yuli Barcohen +zpc1900 powerpc mpc8260 6f80bb48 2014-05-30 Yuli Barcohen +mpc8260ads powerpc mpc8260 facb6725 2014-05-30 Yuli Barcohen +adder powerpc mpc8xx 373a9788 2014-05-30 Yuli Barcohen +quad100hd powerpc ppc405ep 3569571d 2014-05-30 Gary Jennejohn lubbock arm pxa 36bf57b 2014-04-18 Kyle Harris EVB64260 powerpc mpc824x bb3aef9 2014-04-18 MOUSSE powerpc mpc824x 03f2ecc 2014-04-18 diff --git a/include/configs/SIMPC8313.h b/include/configs/SIMPC8313.h deleted file mode 100644 index 46157ccc40..0000000000 --- a/include/configs/SIMPC8313.h +++ /dev/null @@ -1,580 +0,0 @@ -/* - * Copyright (C) Sheldon Instruments, Inc. 2008 - * - * SPDX-License-Identifier: GPL-2.0+ - */ -/* - * simpc8313 board configuration file - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_NAND_U_BOOT - -#define CONFIG_E300 1 -#define CONFIG_MPC831x 1 -#define CONFIG_MPC8313 1 - -#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) -#define CONFIG_SYS_NAND_U_BOOT_DST 0x00100000 -#define CONFIG_SYS_NAND_U_BOOT_START 0x00100100 -#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000 -#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_RELOC + 0x10000) - -#define CONFIG_SYS_TEXT_BASE 0x00100000 /* CONFIG_SYS_NAND_U_BOOT_DST */ -#define CONFIG_SYS_TEXT_BASE_SPL 0xfff00000 - -#ifdef CONFIG_NAND_SPL -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */ -#else -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ -#endif - -#define CONFIG_PCI -#define CONFIG_PCI_INDIRECT_BRIDGE -#define CONFIG_FSL_ELBC 1 - -#define CONFIG_MISC_INIT_R - -/* - * On-board devices - * - * TSEC1 is Marvell PHY 88E1118 - */ - -#define CONFIG_SYS_33MHZ - -#define CONFIG_83XX_CLKIN 33333333 /* in Hz */ - -#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN - -#define CONFIG_SYS_IMMR 0xE0000000 - -#if defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) -#define CONFIG_DEFAULT_IMMR CONFIG_SYS_IMMR -#endif - -#define CONFIG_SYS_MEMTEST_START 0x00001000 -#define CONFIG_SYS_MEMTEST_END 0x07f00000 - -#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */ -#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */ - -/* - * Device configurations - */ -#define CONFIG_TSEC1 - -/* - * DDR Setup - */ - /* DDR is system memory*/ -#define CONFIG_SYS_DDR_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE -#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE - -#define CONFIG_VERY_BIG_RAM -#define CONFIG_MAX_MEM_MAPPED (512 << 20) - -#define CONFIG_SYS_DDRCDR (DDRCDR_EN \ - | DDRCDR_PZ_NOMZ \ - | DDRCDR_NZ_NOMZ \ - | DDRCDR_M_ODR) - /* 0x73000002 TODO ODR & DRN ? */ - -/* - * FLASH on the Local Bus - */ -#define CONFIG_SYS_NO_FLASH - -#if !defined(CONFIG_NAND_SPL) -#define CONFIG_SYS_RAMBOOT -#endif - -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/ - -#define CONFIG_SYS_GBL_DATA_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ - -/* - * Local Bus LCRR and LBCR regs - */ -#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP -#define CONFIG_SYS_LCRR_EADC LCRR_EADC_1 -#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2 -#define CONFIG_SYS_LBC_LBCR (0x00040000 /* TODO */ \ - | (0xFF << LBCR_BMT_SHIFT) \ - | 0xF) /* 0x0004ff0f */ - - /* LB refresh timer prescal, 266MHz/32 */ -#define CONFIG_SYS_LBC_MRTPR 0x20000000 - -/* drivers/mtd/nand/nand.c */ -#ifdef CONFIG_NAND_SPL -#define CONFIG_SYS_NAND_BASE 0xFFF00000 -#else -#define CONFIG_SYS_NAND_BASE 0xE2800000 -#endif -#define CONFIG_SYS_FPGA_BASE 0xFF000000 - -#define CONFIG_CMD_NAND -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_MTD_NAND_VERIFY_WRITE -#define CONFIG_NAND_FSL_ELBC 1 - -#define CONFIG_SYS_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE \ - | BR_DECC_CHK_GEN /* Use HW ECC */ \ - | BR_PS_8 /* 8 bit Port */ \ - | BR_MS_FCM /* MSEL = FCM */ \ - | BR_V) /* valid */ - -#ifdef CONFIG_NAND_SP -#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_32KB \ - | OR_FCM_CSCT \ - | OR_FCM_CST \ - | OR_FCM_CHT \ - | OR_FCM_SCY_1 \ - | OR_FCM_TRLX \ - | OR_FCM_EHTR) -#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) -#define CONFIG_SYS_NAND_PAGE_SIZE 512 /* NAND chip page size */ - /* NAND chip block size */ -#define CONFIG_SYS_NAND_BLOCK_SIZE (16 << 10) -#define NAND_CACHE_PAGES 32 -#elif defined(CONFIG_NAND_LP) -#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_256KB \ - | OR_FCM_PGS \ - | OR_FCM_CSCT \ - | OR_FCM_CST \ - | OR_FCM_CHT \ - | OR_FCM_SCY_1 \ - | OR_FCM_TRLX \ - | OR_FCM_EHTR) -#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_256KB) -#define CONFIG_SYS_NAND_PAGE_SIZE 2048 /* NAND chip page size */ - /* NAND chip block size */ -#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10) -#define NAND_CACHE_PAGES 64 -#else -#error Page size of NAND not defined. -#endif /* CONFIG_NAND_SP */ - -#define CONFIG_SYS_NAND_U_BOOT_OFFS CONFIG_SYS_NAND_BLOCK_SIZE - -#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM -#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM - -#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_NAND_BASE - -#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR0_PRELIM -#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR0_PRELIM - -#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FPGA_BASE \ - | BR_PS_16 \ - | BR_MS_UPMA \ - | BR_V) -#define CONFIG_SYS_OR1_PRELIM (OR_AM_2MB \ - | OR_UPM_BCTLD) - -#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_FPGA_BASE -#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_2MB) - -/* - * JFFS2 configuration - */ -#define CONFIG_JFFS2_NAND -#define CONFIG_JFFS2_DEV "nand0" - -/* mtdparts command line support */ -#define CONFIG_CMD_MTDPARTS -#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ -#define MTDIDS_DEFAULT "nand0=nand0" -#define MTDPARTS_DEFAULT "mtdparts=nand0:2M(u-boot),6M(kernel),-(jffs2)" - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 -#define CONFIG_OF_STDOUT_VIA_ALIAS 1 - -/* - * Serial Port - */ -#define CONFIG_CONS_INDEX 1 -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#ifdef CONFIG_NAND_SPL -#define CONFIG_NS16550_MIN_FUNCTIONS -#endif - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) - -/* Use the HUSH parser */ -#define CONFIG_SYS_HUSH_PARSER - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 400000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 -#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } - -/* - * General PCI - * Addresses are mapped 1-1. - */ -#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 -#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE -#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 -#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE -#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI1_IO_BASE 0x00000000 -#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000 -#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ - -#define CONFIG_PCI_PNP /* do pci plug-and-play */ -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ - -/* - * TSEC - */ -#define CONFIG_TSEC_ENET /* TSEC ethernet support */ - -#define CONFIG_GMII /* MII PHY management */ - -#ifdef CONFIG_TSEC1 -#define CONFIG_HAS_ETH0 -#define CONFIG_TSEC1_NAME "TSEC0" -#define CONFIG_SYS_TSEC1_OFFSET 0x24000 -#define TSEC1_PHY_ADDR 0x0 -#define TSEC1_FLAGS TSEC_GIGABIT -#define TSEC1_PHYIDX 0 -#endif - -#ifdef CONFIG_TSEC2 -#define CONFIG_HAS_ETH1 -#define CONFIG_TSEC2_NAME "TSEC1" -#define CONFIG_SYS_TSEC2_OFFSET 0x25000 -#define TSEC2_PHY_ADDR 4 -#define TSEC2_FLAGS TSEC_GIGABIT -#define TSEC2_PHYIDX 0 -#endif - - -/* Options are: TSEC[0-1] */ -#define CONFIG_ETHPRIME "TSEC1" - -/* - * Configure on-board RTC - */ -#define CONFIG_RTC_DS1337 -#define CONFIG_SYS_I2C_RTC_ADDR 0x68 - -/* - * Environment - */ -#if defined(CONFIG_NAND_U_BOOT) - #define CONFIG_ENV_IS_IN_NAND 1 - #define CONFIG_ENV_OFFSET (768 * 1024) - #define CONFIG_ENV_SECT_SIZE CONFIG_SYS_NAND_BLOCK_SIZE - #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE - #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE - #define CONFIG_ENV_RANGE (CONFIG_ENV_SECT_SIZE * 4) - #define CONFIG_ENV_OFFSET_REDUND \ - (CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE) -#elif !defined(CONFIG_SYS_RAMBOOT) - #define CONFIG_ENV_IS_IN_FLASH 1 - #define CONFIG_ENV_ADDR \ - (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) - #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ - #define CONFIG_ENV_SIZE 0x2000 - -/* Address and size of Redundant Environment Sector */ -#else - #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ - #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) - #define CONFIG_ENV_SIZE 0x2000 -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include -#undef CONFIG_CMD_IMLS -#undef CONFIG_CMD_FLASH - -#define CONFIG_CMD_PING -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_I2C -#define CONFIG_CMD_MII -#define CONFIG_CMD_DATE -#define CONFIG_CMD_PCI -#define CONFIG_CMD_JFFS2 - -#if defined(CONFIG_SYS_RAMBOOT) && !defined(CONFIG_NAND_U_BOOT) - #undef CONFIG_CMD_SAVEENV - #undef CONFIG_CMD_LOADS -#endif - -#define CONFIG_CMDLINE_EDITING 1 -#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ - -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ - + sizeof(CONFIG_SYS_PROMPT) \ - + 16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ - /* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -/* - * For booting Linux, the board info and command line data - * have to be in the first 256 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ - /* Initial Memory map for Linux*/ -#define CONFIG_SYS_BOOTMAPSZ (256 << 20) - -#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */ - -#define CONFIG_SYS_HRCW_LOW (HRCWL_LCL_BUS_TO_SCB_CLK_1X1 \ - | 0x20000000 /* reserved */ \ - | HRCWL_DDR_TO_SCB_CLK_2X1 \ - | HRCWL_CSB_TO_CLKIN_4X1 \ - | HRCWL_CORE_TO_CSB_2_5X1) - -#define CONFIG_SYS_NS16550_CLK (CONFIG_83XX_CLKIN * 4) - -#define CONFIG_SYS_HRCW_HIGH_BASE (HRCWH_PCI_HOST \ - | HRCWH_PCI1_ARBITER_ENABLE \ - | HRCWH_CORE_ENABLE \ - | HRCWH_BOOTSEQ_DISABLE \ - | HRCWH_SW_WATCHDOG_DISABLE \ - | HRCWH_TSEC1M_IN_RGMII \ - | HRCWH_TSEC2M_IN_RGMII \ - | HRCWH_BIG_ENDIAN \ - | HRCWH_LALE_NORMAL) - -#ifdef CONFIG_NAND_LP -#define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE \ - | HRCWH_FROM_0XFFF00100 \ - | HRCWH_ROM_LOC_NAND_LP_8BIT \ - | HRCWH_RL_EXT_NAND) -#else -#define CONFIG_SYS_HRCW_HIGH (CONFIG_SYS_HRCW_HIGH_BASE \ - | HRCWH_FROM_0XFFF00100 \ - | HRCWH_ROM_LOC_NAND_SP_8BIT \ - | HRCWH_RL_EXT_NAND) -#endif - -/* System IO Config */ -#define CONFIG_SYS_SICRH (SICRH_ETSEC2_B \ - | SICRH_ETSEC2_C \ - | SICRH_ETSEC2_D \ - | SICRH_ETSEC2_E \ - | SICRH_ETSEC2_F \ - | SICRH_ETSEC2_G \ - | SICRH_TSOBI1 \ - | SICRH_TSOBI2) -#define CONFIG_SYS_SICRL (SICRL_LBC \ - | SICRL_USBDR_10 \ - | SICRL_ETSEC2_A) - -#define CONFIG_SYS_HID0_INIT 0x000000000 -#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK \ - | HID0_ENABLE_INSTRUCTION_CACHE \ - | HID0_ENABLE_DYNAMIC_POWER_MANAGMENT) - -#define CONFIG_SYS_HID2 HID2_HBE - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -/* DDR @ 0x00000000 */ -#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW) -#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \ - | BATU_BL_256M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_IBAT1L ((CONFIG_SYS_SDRAM_BASE + 0x10000000) \ - | BATL_PP_RW) -#define CONFIG_SYS_IBAT1U ((CONFIG_SYS_SDRAM_BASE + 0x10000000) \ - | BATU_BL_256M \ - | BATU_VS \ - | BATU_VP) - -/* PCI @ 0x80000000 */ -#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_RW) -#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MEM_BASE \ - | BATU_BL_256M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI1_MMIO_BASE \ - | BATL_PP_RW \ - | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI1_MMIO_BASE \ - | BATU_BL_256M \ - | BATU_VS \ - | BATU_VP) - -/* PCI2 not supported on 8313 */ -#define CONFIG_SYS_IBAT4L (0) -#define CONFIG_SYS_IBAT4U (0) - -/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 */ -#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \ - | BATL_PP_RW \ - | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \ - | BATU_BL_256M \ - | BATU_VS \ - | BATU_VP) - -/* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */ -#define CONFIG_SYS_IBAT6L (0xF0000000 \ - | BATL_PP_RW \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT6U (0xF0000000 \ - | BATU_BL_256M \ - | BATU_VS \ - | BATU_VP) - -#define CONFIG_SYS_IBAT7L (0) -#define CONFIG_SYS_IBAT7U (0) - -#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L -#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U -#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U -#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L -#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U -#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L -#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U -#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L -#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U -#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L -#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U -#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L -#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U -#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L -#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U - -/* - * Environment Configuration - */ -#define CONFIG_ENV_OVERWRITE - -#define CONFIG_NETDEV "eth1" - -#define CONFIG_HOSTNAME simpc8313 -#define CONFIG_ROOTPATH "/tftpboot/" -#define CONFIG_BOOTFILE "/tftpboot/uImage" - /* U-Boot image on TFTP server */ -#define CONFIG_UBOOTPATH "u-boot-nand.bin" -#define CONFIG_FDTFILE "simpc8313.dtb" - - /* default location for tftp and bootm */ -#define CONFIG_LOADADDR 500000 -#define CONFIG_BOOTDELAY 5 /* 5 second delay */ -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_BOOTCOMMAND "nand read $loadaddr kernel 600000;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=" CONFIG_NETDEV "\0" \ - "ethprime=TSEC1\0" \ - "uboot=" CONFIG_UBOOTPATH "\0" \ - "tftpflash=tftpboot $loadaddr $uboot; " \ - "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ - " $filesize; " \ - "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ - " +$filesize; " \ - "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ - " $filesize\0" \ - "fdtaddr=ae0000\0" \ - "fdtfile=" CONFIG_FDTFILE "\0" \ - "console=ttyS0\0" \ - "setbootargs=setenv bootargs " \ - "root=$rootdev rw console=$console,$baudrate $othbootargs\0" \ - "setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \ - "$netdev:off " \ - "root=$rootdev rw console=$console,$baudrate $othbootargs\0" \ - "load_uboot=tftp 100000 u-boot-nand.bin\0" \ - "burn_uboot=nand erase u-boot 80000; " \ - "nand write 100000 u-boot $filesize\0" \ - "update_uboot=run load_uboot;run burn_uboot\0" \ - "mtdids=nand0=nand0\0" \ - "mtdparts=mtdparts=nand0:2M(u-boot),6M(kernel),-(jffs2)\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \ - "bootargs=root=/dev/mtdblock2 rootfstype=jffs2 rw " \ - "console=ttyS0,115200\0" \ - "" - -#define CONFIG_NFSBOOTCOMMAND \ - "setenv rootdev /dev/nfs;" \ - "run setbootargs;" \ - "run setipargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" - -#define CONFIG_RAMBOOTCOMMAND \ - "setenv rootdev /dev/ram;" \ - "run setbootargs;" \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" - -#endif /* __CONFIG_H */ diff --git a/nand_spl/board/sheldon/simpc8313/Makefile b/nand_spl/board/sheldon/simpc8313/Makefile deleted file mode 100644 index 657f65fd22..0000000000 --- a/nand_spl/board/sheldon/simpc8313/Makefile +++ /dev/null @@ -1,81 +0,0 @@ -# -# (C) Copyright 2007 -# Stefan Roese, DENX Software Engineering, sr@denx.de. -# (C) Copyright 2008 Freescale Semiconductor -# (C) Copyright Sheldon Instruments, Inc. 2008 -# -# SPDX-License-Identifier: GPL-2.0+ -# - -include $(srctree)/$(src)/config.mk - -nandobj := $(objtree)/nand_spl/ - -LDSCRIPT= $(srctree)/nand_spl/board/$(BOARDDIR)/u-boot.lds -LDFLAGS := -T $(nandobj)u-boot.lds -Ttext $(CONFIG_SYS_TEXT_BASE_SPL) \ - $(LDFLAGS) $(LDFLAGS_FINAL) -asflags-y += -DCONFIG_NAND_SPL -ccflags-y += -DCONFIG_NAND_SPL - -SOBJS = start.o ticks.o -COBJS = nand_boot_fsl_elbc.o $(BOARD).o sdram.o ns16550.o spl_minimal.o \ - time.o cache.o - -OBJS := $(addprefix $(obj)/,$(SOBJS) $(COBJS)) -__OBJS := $(SOBJS) $(COBJS) -LNDIR := $(nandobj)board/$(BOARDDIR) - -targets += $(__OBJS) - -all: $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin - -$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl - $(OBJCOPY) $(OBJCOPYFLAGS) --pad-to=$(PAD_TO) -O binary $< $@ - -$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl - $(OBJCOPY) $(OBJCOPYFLAGS) -O binary $< $@ - -$(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot.lds - cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) $(PLATFORM_LIBS) \ - -Map $(nandobj)u-boot-spl.map -o $@ - -$(nandobj)u-boot.lds: $(LDSCRIPT) - $(CPP) $(cpp_flags) $(LDPPFLAGS) -ansi -D__ASSEMBLY__ -P - <$^ >$@ - -# create symbolic links for common files - -$(obj)/start.S: - @rm -f $@ - ln -s $(srctree)/arch/powerpc/cpu/mpc83xx/start.S $@ - -$(obj)/nand_boot_fsl_elbc.c: - @rm -f $@ - ln -s $(srctree)/nand_spl/nand_boot_fsl_elbc.c $@ - -$(obj)/sdram.c: - @rm -f $@ - ln -s $(srctree)/board/$(BOARDDIR)/sdram.c $@ - -$(obj)/$(BOARD).c: - @rm -f $@ - ln -s $(srctree)/board/$(BOARDDIR)/$(BOARD).c $@ - -$(obj)/ns16550.c: - @rm -f $@ - ln -s $(srctree)/drivers/serial/ns16550.c $@ - -$(obj)/spl_minimal.c: - @rm -f $@ - ln -s $(srctree)/arch/powerpc/cpu/mpc83xx/spl_minimal.c $@ - -$(obj)/cache.c: - @rm -f $@ - ln -s $(srctree)/arch/powerpc/lib/cache.c $@ - -$(obj)/time.c: - @rm -f $@ - ln -s $(srctree)/arch/powerpc/lib/time.c $@ - -$(obj)/ticks.S: - @rm -f $@ - ln -s $(srctree)/arch/powerpc/lib/ticks.S $@ diff --git a/nand_spl/board/sheldon/simpc8313/config.mk b/nand_spl/board/sheldon/simpc8313/config.mk deleted file mode 100644 index d1b4e2eeb6..0000000000 --- a/nand_spl/board/sheldon/simpc8313/config.mk +++ /dev/null @@ -1,5 +0,0 @@ -ifdef CONFIG_NAND_LP -PAD_TO = 0xFFF20000 -else -PAD_TO = 0xFFF04000 -endif diff --git a/nand_spl/board/sheldon/simpc8313/u-boot.lds b/nand_spl/board/sheldon/simpc8313/u-boot.lds deleted file mode 100644 index 4e4d511f9b..0000000000 --- a/nand_spl/board/sheldon/simpc8313/u-boot.lds +++ /dev/null @@ -1,38 +0,0 @@ -/* - * (C) Copyright 2006 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * Copyright 2008 Freescale Semiconductor, Inc. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_ARCH(powerpc) -SECTIONS -{ - . = 0xfff00000; - .text : { - *(.text*) - . = ALIGN(16); - *(.eh_frame) - *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*))) - } - - . = ALIGN(8); - .data : { - *(.data*) - *(.sdata*) - _GOT2_TABLE_ = .; - *(.got2) - KEEP(*(.got)) - PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4); - } - __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1; - - . = ALIGN(8); - __bss_start = .; - .bss (NOLOAD) : { *(.*bss) } - __bss_end = .; -} -ENTRY(_start) -ASSERT(__bss_end <= 0xfff01000, "NAND bootstrap too big");