diff --git a/board/ti/am335x/board.c b/board/ti/am335x/board.c
index 013ad881f0..e5ad76e9a0 100644
--- a/board/ti/am335x/board.c
+++ b/board/ti/am335x/board.c
@@ -68,6 +68,11 @@ static inline int board_is_evm_sk(void)
 	return !strncmp("A335X_SK", header.name, HDR_NAME_LEN);
 }
 
+static inline int board_is_idk(void)
+{
+	return !strncmp(header.config, "SKU#02", 6);
+}
+
 /*
  * Read header information from EEPROM into global structure.
  */
@@ -378,7 +383,7 @@ int board_eth_init(bd_t *bis)
 			return -1;
 	}
 
-	if (board_is_bone() || board_is_bone_lt()) {
+	if (board_is_bone() || board_is_bone_lt() || board_is_idk()) {
 		writel(MII_MODE_ENABLE, &cdev->miisel);
 		cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if =
 				PHY_INTERFACE_MODE_MII;
diff --git a/board/ti/am335x/mux.c b/board/ti/am335x/mux.c
index acb8ff3e5c..8437ef515a 100644
--- a/board/ti/am335x/mux.c
+++ b/board/ti/am335x/mux.c
@@ -69,6 +69,17 @@ static struct module_pin_mux mmc0_pin_mux[] = {
 	{-1},
 };
 
+static struct module_pin_mux mmc0_no_cd_pin_mux[] = {
+	{OFFSET(mmc0_dat3), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_DAT3 */
+	{OFFSET(mmc0_dat2), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_DAT2 */
+	{OFFSET(mmc0_dat1), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_DAT1 */
+	{OFFSET(mmc0_dat0), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_DAT0 */
+	{OFFSET(mmc0_clk), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_CLK */
+	{OFFSET(mmc0_cmd), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_CMD */
+	{OFFSET(mcasp0_aclkr), (MODE(4) | RXACTIVE)},		/* MMC0_WP */
+	{-1},
+};
+
 static struct module_pin_mux mmc0_pin_mux_sk_evm[] = {
 	{OFFSET(mmc0_dat3), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_DAT3 */
 	{OFFSET(mmc0_dat2), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_DAT2 */
@@ -250,6 +261,15 @@ void enable_board_pin_mux(struct am335x_baseboard_id *header)
 			configure_module_pin_mux(mmc1_pin_mux);
 			configure_module_pin_mux(spi0_pin_mux);
 		}
+	} else if (!strncmp(header->config, "SKU#02", 6)) {
+		/*
+		 * Industrial Motor Control (IDK)
+		 * note: IDK console is on UART3 by default.
+		 *       So u-boot mus be build with CONFIG_SERIAL4 and
+		 *       CONFIG_CONS_INDEX=4
+		 */
+		configure_module_pin_mux(mii1_pin_mux);
+		configure_module_pin_mux(mmc0_no_cd_pin_mux);
 	} else if (!strncmp(header->name, "A335X_SK", HDR_NAME_LEN)) {
 		/* Starter Kit EVM */
 		configure_module_pin_mux(i2c1_pin_mux);