avr32: delete non generic board mimc200

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This commit is contained in:
Andreas Bießmann 2015-05-11 13:07:26 +02:00
parent e369307644
commit c62d2f8fc5
7 changed files with 0 additions and 407 deletions

View file

@ -29,15 +29,11 @@ config TARGET_ATSTK1006
config TARGET_GRASSHOPPER config TARGET_GRASSHOPPER
bool "Support grasshopper" bool "Support grasshopper"
config TARGET_MIMC200
bool "Support mimc200"
endchoice endchoice
source "board/atmel/atngw100/Kconfig" source "board/atmel/atngw100/Kconfig"
source "board/atmel/atngw100mkii/Kconfig" source "board/atmel/atngw100mkii/Kconfig"
source "board/atmel/atstk1000/Kconfig" source "board/atmel/atstk1000/Kconfig"
source "board/in-circuit/grasshopper/Kconfig" source "board/in-circuit/grasshopper/Kconfig"
source "board/mimc/mimc200/Kconfig"
endmenu endmenu

View file

@ -1,15 +0,0 @@
if TARGET_MIMC200
config SYS_BOARD
default "mimc200"
config SYS_VENDOR
default "mimc"
config SYS_SOC
default "at32ap700x"
config SYS_CONFIG_NAME
default "mimc200"
endif

View file

@ -1,6 +0,0 @@
MIMC200 BOARD
M: Mark Jackson <mpfj@mimc.co.uk>
S: Maintained
F: board/mimc/mimc200/
F: include/configs/mimc200.h
F: configs/mimc200_defconfig

View file

@ -1,6 +0,0 @@
#
# Copyright (C) 2005-2006 Atmel Corporation
#
# SPDX-License-Identifier: GPL-2.0+
obj-y := mimc200.o

View file

@ -1,197 +0,0 @@
/*
* Copyright (C) 2006 Atmel Corporation
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <netdev.h>
#include <asm/io.h>
#include <asm/sdram.h>
#include <asm/arch/clk.h>
#include <asm/arch/gpio.h>
#include <asm/arch/hmatrix.h>
#include <asm/arch/mmu.h>
#include <asm/arch/portmux.h>
#include <atmel_lcdc.h>
#include <lcd.h>
#include "../../../arch/avr32/cpu/hsmc3.h"
struct mmu_vm_range mmu_vmr_table[CONFIG_SYS_NR_VM_REGIONS] = {
{
.virt_pgno = CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT,
.nr_pages = CONFIG_SYS_FLASH_SIZE >> MMU_PAGE_SHIFT,
.phys = (CONFIG_SYS_FLASH_BASE >> MMU_PAGE_SHIFT)
| MMU_VMR_CACHE_NONE,
}, {
.virt_pgno = EBI_SRAM_CS2_BASE >> MMU_PAGE_SHIFT,
.nr_pages = EBI_SRAM_CS2_SIZE >> MMU_PAGE_SHIFT,
.phys = (EBI_SRAM_CS2_BASE >> MMU_PAGE_SHIFT)
| MMU_VMR_CACHE_NONE,
}, {
.virt_pgno = CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT,
.nr_pages = EBI_SDRAM_SIZE >> MMU_PAGE_SHIFT,
.phys = (CONFIG_SYS_SDRAM_BASE >> MMU_PAGE_SHIFT)
| MMU_VMR_CACHE_WRBACK,
},
};
#if defined(CONFIG_LCD)
/* 480x272x16 @ 72 Hz */
vidinfo_t panel_info = {
.vl_col = 480, /* Number of columns */
.vl_row = 272, /* Number of rows */
.vl_clk = 5000000, /* pixel clock in ps */
.vl_sync = ATMEL_LCDC_INVCLK_INVERTED |
ATMEL_LCDC_INVLINE_INVERTED |
ATMEL_LCDC_INVFRAME_INVERTED,
.vl_bpix = LCD_COLOR16, /* Bits per pixel, BPP = 2^n */
.vl_tft = 1, /* 0 = passive, 1 = TFT */
.vl_hsync_len = 42, /* Length of horizontal sync */
.vl_left_margin = 1, /* Time from sync to picture */
.vl_right_margin = 1, /* Time from picture to sync */
.vl_vsync_len = 1, /* Length of vertical sync */
.vl_upper_margin = 12, /* Time from sync to picture */
.vl_lower_margin = 1, /* Time from picture to sync */
.mmio = LCDC_BASE, /* Memory mapped registers */
};
void lcd_enable(void)
{
}
void lcd_disable(void)
{
}
#endif
DECLARE_GLOBAL_DATA_PTR;
static const struct sdram_config sdram_config = {
.data_bits = SDRAM_DATA_16BIT,
.row_bits = 13,
.col_bits = 9,
.bank_bits = 2,
.cas = 3,
.twr = 2,
.trc = 6,
.trp = 2,
.trcd = 2,
.tras = 6,
.txsr = 6,
/* 15.6 us */
.refresh_period = (156 * (SDRAMC_BUS_HZ / 1000)) / 10000,
};
int board_early_init_f(void)
{
/* Enable SDRAM in the EBI mux */
hmatrix_slave_write(EBI, SFR, HMATRIX_BIT(EBI_SDRAM_ENABLE));
/* Enable 26 address bits and NCS2 */
portmux_enable_ebi(16, 26, PORTMUX_EBI_CS(2), PORTMUX_DRIVE_HIGH);
sdram_init(uncached(EBI_SDRAM_BASE), &sdram_config);
portmux_enable_usart1(PORTMUX_DRIVE_MIN);
/* de-assert "force sys reset" pin */
portmux_select_gpio(PORTMUX_PORT_D, 1 << 15,
PORTMUX_DIR_OUTPUT | PORTMUX_INIT_HIGH);
/* init custom i/o */
/* cpu type inputs */
portmux_select_gpio(PORTMUX_PORT_E, (1 << 19) | (1 << 20) | (1 << 23),
PORTMUX_DIR_INPUT);
/* main board type inputs */
portmux_select_gpio(PORTMUX_PORT_B, (1 << 19) | (1 << 29),
PORTMUX_DIR_INPUT);
/* DEBUG input (use weak pullup) */
portmux_select_gpio(PORTMUX_PORT_E, 1 << 21,
PORTMUX_DIR_INPUT | PORTMUX_PULL_UP);
/* are we suppressing the console ? */
if (gpio_get_value(GPIO_PIN_PE(21)) == 1)
gd->flags |= (GD_FLG_SILENT | GD_FLG_DISABLE_CONSOLE);
/* reset phys */
portmux_select_gpio(PORTMUX_PORT_E, 1 << 24, PORTMUX_DIR_INPUT);
portmux_select_gpio(PORTMUX_PORT_C, 1 << 18,
PORTMUX_DIR_OUTPUT | PORTMUX_INIT_HIGH);
udelay(5000);
/* release phys reset */
gpio_set_value(GPIO_PIN_PC(18), 0); /* PHY RESET (Release) */
/* setup Data Flash chip select (NCS2) */
hsmc3_writel(MODE2, 0x20121003);
hsmc3_writel(CYCLE2, 0x000a0009);
hsmc3_writel(PULSE2, 0x0a060806);
hsmc3_writel(SETUP2, 0x00030102);
/* setup FRAM chip select (NCS3) */
hsmc3_writel(MODE3, 0x10120001);
hsmc3_writel(CYCLE3, 0x001e001d);
hsmc3_writel(PULSE3, 0x08040704);
hsmc3_writel(SETUP3, 0x02050204);
#if defined(CONFIG_MACB)
/* init macb0 pins */
portmux_enable_macb0(PORTMUX_MACB_MII, PORTMUX_DRIVE_HIGH);
portmux_enable_macb1(PORTMUX_MACB_MII, PORTMUX_DRIVE_HIGH);
#endif
#if defined(CONFIG_MMC)
portmux_enable_mmci(0, PORTMUX_MMCI_4BIT, PORTMUX_DRIVE_LOW);
#endif
#if defined(CONFIG_LCD)
portmux_enable_lcdc(1);
#endif
return 0;
}
int board_early_init_r(void)
{
gd->bd->bi_phy_id[0] = 0x01;
gd->bd->bi_phy_id[1] = 0x03;
return 0;
}
int board_postclk_init(void)
{
/* Use GCLK0 as 10MHz output */
gclk_enable_output(0, PORTMUX_DRIVE_LOW);
gclk_set_rate(0, GCLK_PARENT_OSC0, 10000000);
return 0;
}
/* SPI chip select control */
#ifdef CONFIG_ATMEL_SPI
#include <spi.h>
int spi_cs_is_valid(unsigned int bus, unsigned int cs)
{
return (bus == 0) && (cs == 0);
}
void spi_cs_activate(struct spi_slave *slave)
{
}
void spi_cs_deactivate(struct spi_slave *slave)
{
}
#endif /* CONFIG_ATMEL_SPI */
#ifdef CONFIG_CMD_NET
int board_eth_init(bd_t *bi)
{
macb_eth_initialize(0, (void *)ATMEL_BASE_MACB0, bi->bi_phy_id[0]);
macb_eth_initialize(1, (void *)ATMEL_BASE_MACB1, bi->bi_phy_id[1]);
return 0;
}
#endif

View file

@ -1,3 +0,0 @@
CONFIG_AVR32=y
CONFIG_TARGET_MIMC200=y
CONFIG_CMD_NET=y

View file

@ -1,176 +0,0 @@
/*
* Copyright (C) 2006 Atmel Corporation
*
* Configuration settings for the AVR32 Network Gateway
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <asm/arch/hardware.h>
#define CONFIG_AT32AP
#define CONFIG_AT32AP7000
#define CONFIG_MIMC200
#define CONFIG_MIMC200_EXT_FLASH
/*
* Set up the PLL to run at 140 MHz, the CPU to run at the PLL
* frequency, the HSB and PBB busses to run at 1/2 the PLL frequency
* and the PBA bus to run at 1/4 the PLL frequency.
*/
#define CONFIG_PLL
#define CONFIG_SYS_POWER_MANAGER
#define CONFIG_SYS_OSC0_HZ 10000000
#define CONFIG_SYS_PLL0_DIV 1
#define CONFIG_SYS_PLL0_MUL 15
#define CONFIG_SYS_PLL0_SUPPRESS_CYCLES 16
#define CONFIG_SYS_CLKDIV_CPU 0
#define CONFIG_SYS_CLKDIV_HSB 1
#define CONFIG_SYS_CLKDIV_PBA 2
#define CONFIG_SYS_CLKDIV_PBB 1
/* Reserve VM regions for SDRAM, NOR flash and FRAM */
#define CONFIG_SYS_NR_VM_REGIONS 3
/*
* The PLLOPT register controls the PLL like this:
* icp = PLLOPT<2>
* ivco = PLLOPT<1:0>
*
* We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz).
*/
#define CONFIG_SYS_PLL0_OPT 0x04
#define CONFIG_USART_BASE ATMEL_BASE_USART1
#define CONFIG_USART_ID 1
#define CONFIG_MIMC200_DBGLINK 1
/* User serviceable stuff */
#define CONFIG_DOS_PARTITION
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_STACKSIZE (2048)
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTARGS \
"root=/dev/mtdblock1 rootfstype=jffs2 fbmem=512k console=ttyS1"
#define CONFIG_BOOTCOMMAND \
"fsload boot/uImage; bootm"
#define CONFIG_SILENT_CONSOLE /* enable silent startup */
#define CONFIG_DISABLE_CONSOLE /* disable console */
#define CONFIG_SYS_DEVICE_NULLDEV /* include nulldev device */
#define CONFIG_LCD 1
/*
* Only interrupt autoboot if <space> is pressed. Otherwise, garbage
* data on the serial line may interrupt the boot sequence.
*/
#define CONFIG_BOOTDELAY 0
#define CONFIG_ZERO_BOOTDELAY_CHECK
#define CONFIG_AUTOBOOT
/*
* After booting the board for the first time, new ethernet addresses
* should be generated and assigned to the environment variables
* "ethaddr" and "eth1addr". This is normally done during production.
*/
#define CONFIG_OVERWRITE_ETHADDR_ONCE
/*
* BOOTP/DHCP options
*/
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_MMC
#define CONFIG_ATMEL_USART
#define CONFIG_MACB
#define CONFIG_PORTMUX_PIO
#define CONFIG_SYS_NR_PIOS 5
#define CONFIG_SYS_HSDRAMC
#define CONFIG_MMC
#define CONFIG_GENERIC_ATMEL_MCI
#define CONFIG_GENERIC_MMC
#if defined(CONFIG_LCD)
#define CONFIG_CMD_BMP
#define CONFIG_ATMEL_LCD 1
#define LCD_BPP LCD_COLOR16
#define CONFIG_BMP_16BPP 1
#define CONFIG_FB_ADDR 0x10600000
#define CONFIG_WHITE_ON_BLACK 1
#define CONFIG_VIDEO_BMP_GZIP 1
#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE 262144
#define CONFIG_ATMEL_LCD_BGR555 1
#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
#define CONFIG_SPLASH_SCREEN 1
#endif
#define CONFIG_SYS_DCACHE_LINESZ 32
#define CONFIG_SYS_ICACHE_LINESZ 32
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_BASE 0x00000000
#define CONFIG_SYS_FLASH_SIZE 0x800000
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_MAX_FLASH_SECT 135
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_TEXT_BASE 0x00000000
#define CONFIG_SYS_INTRAM_BASE INTERNAL_SRAM_BASE
#define CONFIG_SYS_INTRAM_SIZE INTERNAL_SRAM_SIZE
#define CONFIG_SYS_SDRAM_BASE EBI_SDRAM_BASE
#define CONFIG_SYS_FRAM_BASE 0x08000000
#define CONFIG_SYS_FRAM_SIZE 0x20000
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_SIZE 65536
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE - CONFIG_ENV_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INTRAM_BASE + CONFIG_SYS_INTRAM_SIZE)
#define CONFIG_SYS_MALLOC_LEN (1024*1024)
/* Allow 4MB for the kernel run-time image */
#define CONFIG_SYS_LOAD_ADDR (EBI_SDRAM_BASE + 0x00400000)
#define CONFIG_SYS_BOOTPARAMS_LEN (16 * 1024)
/* Other configuration settings that shouldn't have to change all that often */
#define CONFIG_SYS_PROMPT "U-Boot> "
#define CONFIG_SYS_CBSIZE 256
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_LONGHELP
#define CONFIG_SYS_MEMTEST_START EBI_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x1f00000)
#define CONFIG_SYS_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 }
#endif /* __CONFIG_H */