diff --git a/README b/README
index 2fe3f08f4b..e2ca76e7ae 100644
--- a/README
+++ b/README
@@ -1954,6 +1954,19 @@ CBFS (Coreboot Filesystem) support
 		interface.
 
 		ported i2c driver to the new framework:
+		- drivers/i2c/soft_i2c.c:
+		  - activate first bus with CONFIG_SYS_I2C_SOFT define
+		    CONFIG_SYS_I2C_SOFT_SPEED and CONFIG_SYS_I2C_SOFT_SLAVE
+		    for defining speed and slave address
+		  - activate second bus with I2C_SOFT_DECLARATIONS2 define
+		    CONFIG_SYS_I2C_SOFT_SPEED_2 and CONFIG_SYS_I2C_SOFT_SLAVE_2
+		    for defining speed and slave address
+		  - activate third bus with I2C_SOFT_DECLARATIONS3 define
+		    CONFIG_SYS_I2C_SOFT_SPEED_3 and CONFIG_SYS_I2C_SOFT_SLAVE_3
+		    for defining speed and slave address
+		  - activate fourth bus with I2C_SOFT_DECLARATIONS4 define
+		    CONFIG_SYS_I2C_SOFT_SPEED_4 and CONFIG_SYS_I2C_SOFT_SLAVE_4
+		    for defining speed and slave address
 
 		additional defines:
 
@@ -1992,18 +2005,18 @@ CBFS (Coreboot Filesystem) support
 
 		which defines
 			bus 0 on adapter 0 without a mux
-			bus 1 on adapter 0 without a PCA9547 on address 0x70 port 1
-			bus 2 on adapter 0 without a PCA9547 on address 0x70 port 2
-			bus 3 on adapter 0 without a PCA9547 on address 0x70 port 3
-			bus 4 on adapter 0 without a PCA9547 on address 0x70 port 4
-			bus 5 on adapter 0 without a PCA9547 on address 0x70 port 5
+			bus 1 on adapter 0 with a PCA9547 on address 0x70 port 1
+			bus 2 on adapter 0 with a PCA9547 on address 0x70 port 2
+			bus 3 on adapter 0 with a PCA9547 on address 0x70 port 3
+			bus 4 on adapter 0 with a PCA9547 on address 0x70 port 4
+			bus 5 on adapter 0 with a PCA9547 on address 0x70 port 5
 			bus 6 on adapter 1 without a mux
-			bus 7 on adapter 1 without a PCA9544 on address 0x72 port 1
-			bus 8 on adapter 1 without a PCA9544 on address 0x72 port 2
+			bus 7 on adapter 1 with a PCA9544 on address 0x72 port 1
+			bus 8 on adapter 1 with a PCA9544 on address 0x72 port 2
 
 		If you do not have i2c muxes on your board, omit this define.
 
-- Legacy I2C Support:	CONFIG_HARD_I2C | CONFIG_SOFT_I2C
+- Legacy I2C Support:	CONFIG_HARD_I2C
 
 		NOTE: It is intended to move drivers to CONFIG_SYS_I2C which
 		provides the following compelling advantages:
@@ -2014,9 +2027,9 @@ CBFS (Coreboot Filesystem) support
 
 		** Please consider updating your I2C driver now. **
 
-		These enable legacy I2C serial bus commands. Defining either of
-		(but not both of) CONFIG_HARD_I2C or CONFIG_SOFT_I2C will
-		include the appropriate I2C driver for the selected CPU.
+		These enable legacy I2C serial bus commands. Defining
+		CONFIG_HARD_I2C will include the appropriate I2C driver
+		for the selected CPU.
 
 		This will allow you to use i2c commands at the u-boot
 		command line (as long as you set CONFIG_CMD_I2C in
@@ -2026,12 +2039,8 @@ CBFS (Coreboot Filesystem) support
 
 		CONFIG_HARD_I2C selects a hardware I2C controller.
 
-		CONFIG_SOFT_I2C configures u-boot to use a software (aka
-		bit-banging) driver instead of CPM or similar hardware
-		support for I2C.
-
 		There are several other quantities that must also be
-		defined when you define CONFIG_HARD_I2C or CONFIG_SOFT_I2C.
+		defined when you define CONFIG_HARD_I2C.
 
 		In both cases you will need to define CONFIG_SYS_I2C_SPEED
 		to be the frequency (in Hz) at which you wish your i2c bus
@@ -2053,7 +2062,7 @@ CBFS (Coreboot Filesystem) support
 
 		That's all that's required for CONFIG_HARD_I2C.
 
-		If you use the software i2c interface (CONFIG_SOFT_I2C)
+		If you use the software i2c interface (CONFIG_SYS_I2C_SOFT)
 		then the following macros need to be defined (examples are
 		from include/configs/lwmon.h):
 
@@ -3672,7 +3681,7 @@ to save the current settings.
 	  I2C muxes, you can define here, how to reach this
 	  EEPROM. For example:
 
-	  #define CONFIG_I2C_ENV_EEPROM_BUS	  "pca9547:70:d\0"
+	  #define CONFIG_I2C_ENV_EEPROM_BUS	  1
 
 	  EEPROM which holds the environment, is reached over
 	  a pca9547 i2c mux with address 0x70, channel 3.
diff --git a/arch/arm/include/asm/arch-kirkwood/config.h b/arch/arm/include/asm/arch-kirkwood/config.h
index a9499b70cd..f0e84e62b0 100644
--- a/arch/arm/include/asm/arch-kirkwood/config.h
+++ b/arch/arm/include/asm/arch-kirkwood/config.h
@@ -144,7 +144,7 @@
  * I2C related stuff
  */
 #ifdef CONFIG_CMD_I2C
-#ifndef CONFIG_SOFT_I2C
+#ifndef CONFIG_SYS_I2C_SOFT
 #define CONFIG_I2C_MVTWSI
 #endif
 #define CONFIG_SYS_I2C_SLAVE		0x0
diff --git a/arch/arm/lib/board.c b/arch/arm/lib/board.c
index 5302a1369c..5360883db7 100644
--- a/arch/arm/lib/board.c
+++ b/arch/arm/lib/board.c
@@ -69,7 +69,6 @@ extern void dataflash_print_info(void);
 #endif
 
 #if defined(CONFIG_HARD_I2C) || \
-	defined(CONFIG_SOFT_I2C) || \
 	defined(CONFIG_SYS_I2C)
 #include <i2c.h>
 #endif
@@ -166,7 +165,7 @@ static int display_dram_config(void)
 	return (0);
 }
 
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C)
 static int init_func_i2c(void)
 {
 	puts("I2C:   ");
@@ -273,7 +272,7 @@ init_fnc_t *init_sequence[] = {
 #if defined(CONFIG_DISPLAY_BOARDINFO)
 	checkboard,		/* display board info */
 #endif
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C)
 	init_func_i2c,
 #endif
 	dram_init,		/* configure available RAM banks */
diff --git a/arch/m68k/lib/board.c b/arch/m68k/lib/board.c
index 582f47b50e..2baafa5df3 100644
--- a/arch/m68k/lib/board.c
+++ b/arch/m68k/lib/board.c
@@ -56,7 +56,7 @@
 #include <version.h>
 
 #if defined(CONFIG_HARD_I2C) || \
-	defined(CONFIG_SOFT_I2C)
+	defined(CONFIG_SYS_I2C)
 #include <i2c.h>
 #endif
 
@@ -142,8 +142,7 @@ static int init_func_ram (void)
 
 /***********************************************************************/
 
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) || \
-		defined(CONFIG_SYS_I2C)
+#if defined(CONFIG_HARD_I2C) ||	defined(CONFIG_SYS_I2C)
 static int init_func_i2c (void)
 {
 	puts ("I2C:   ");
@@ -183,8 +182,7 @@ init_fnc_t *init_sequence[] = {
 	display_options,
 	checkcpu,
 	checkboard,
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) || \
-		defined(CONFIG_SYS_I2C)
+#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C)
 	init_func_i2c,
 #endif
 #if defined(CONFIG_HARD_SPI)
diff --git a/arch/powerpc/lib/board.c b/arch/powerpc/lib/board.c
index 0c2e008e00..bc7c362cf2 100644
--- a/arch/powerpc/lib/board.c
+++ b/arch/powerpc/lib/board.c
@@ -98,8 +98,7 @@ extern void sc3_read_eeprom(void);
 #if defined(CONFIG_CMD_DOC)
 void doc_init(void);
 #endif
-#if defined(CONFIG_HARD_I2C) || \
-	defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C)
 #include <i2c.h>
 #endif
 #include <spi.h>
@@ -214,8 +213,7 @@ static int init_func_ram(void)
 
 /***********************************************************************/
 
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) || \
-		defined(CONFIG_SYS_I2C)
+#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C)
 static int init_func_i2c(void)
 {
 	puts("I2C:   ");
@@ -312,8 +310,7 @@ static init_fnc_t *init_sequence[] = {
 	misc_init_f,
 #endif
 	INIT_FUNC_WATCHDOG_RESET
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) || \
-		defined(CONFIG_SYS_I2C)
+#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C)
 	init_func_i2c,
 #endif
 #if defined(CONFIG_HARD_SPI)
diff --git a/board/BuS/eb_cpux9k2/cpux9k2.c b/board/BuS/eb_cpux9k2/cpux9k2.c
index e98244b5ed..01b4382c61 100644
--- a/board/BuS/eb_cpux9k2/cpux9k2.c
+++ b/board/BuS/eb_cpux9k2/cpux9k2.c
@@ -288,7 +288,7 @@ int drv_video_init(void)
 }
 #endif
 
-#ifdef CONFIG_SOFT_I2C
+#ifdef CONFIG_SYS_I2C_SOFT
 
 void i2c_init_board(void)
 {
diff --git a/board/BuS/vl_ma2sc/vl_ma2sc.c b/board/BuS/vl_ma2sc/vl_ma2sc.c
index 84b2060aed..7e086eeab4 100644
--- a/board/BuS/vl_ma2sc/vl_ma2sc.c
+++ b/board/BuS/vl_ma2sc/vl_ma2sc.c
@@ -323,7 +323,7 @@ int board_eth_init(bd_t *bis)
 	return rc;
 }
 
-#ifdef CONFIG_SOFT_I2C
+#ifdef CONFIG_SYS_I2C_SOFT
 void i2c_init_board(void)
 {
 	u32 pin;
diff --git a/board/atc/atc.c b/board/atc/atc.c
index 936c031c67..c2b5a1f65c 100644
--- a/board/atc/atc.c
+++ b/board/atc/atc.c
@@ -170,7 +170,7 @@ const iop_conf_t iop_conf_tab[4][32] = {
 	/* PD18 */ {   0,   0,   0,   0,   0,   0   }, /* PD18 */
 	/* PD17 */ {   0,   0,   0,   0,   0,   0   }, /* PD17 */
 	/* PD16 */ {   0,   0,   0,   0,   0,   0   }, /* PD16 */
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
 	/* PD15 */ {   1,   0,   0,   1,   1,   1   }, /* I2C SDA */
 	/* PD14 */ {   1,   0,   0,   1,   1,   1   }, /* I2C SCL */
 #else
diff --git a/board/bluewater/snapper9260/snapper9260.c b/board/bluewater/snapper9260/snapper9260.c
index 60c55e9be8..b4378db18c 100644
--- a/board/bluewater/snapper9260/snapper9260.c
+++ b/board/bluewater/snapper9260/snapper9260.c
@@ -145,7 +145,7 @@ int board_init(void)
 
 	/* Initialise peripherals */
 	at91_seriald_hw_init();
-	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+	i2c_set_bus_num(0);
 	nand_hw_init();
 	macb_hw_init();
 
diff --git a/board/cm5200/cm5200.c b/board/cm5200/cm5200.c
index c0ea1c6229..ad50452b05 100644
--- a/board/cm5200/cm5200.c
+++ b/board/cm5200/cm5200.c
@@ -325,7 +325,7 @@ int board_early_init_r(void)
 #ifdef CONFIG_MISC_INIT_R
 int misc_init_r(void)
 {
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT)
 	uchar buf[6];
 	char str[18];
 	char hostname[MODULE_NAME_MAXLEN];
@@ -348,7 +348,7 @@ int misc_init_r(void)
 			" device at address %02X:%04X\n", CONFIG_SYS_I2C_EEPROM,
 			CONFIG_MAC_OFFSET);
 	}
-#endif /* defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) */
+#endif /* defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT) */
 	if (!getenv("ethaddr"))
 		printf(LOG_PREFIX "MAC address not set, networking is not "
 					"operational\n");
diff --git a/board/cpu86/cpu86.c b/board/cpu86/cpu86.c
index bc7ebfea18..1d4f90cdd1 100644
--- a/board/cpu86/cpu86.c
+++ b/board/cpu86/cpu86.c
@@ -161,7 +161,7 @@ const iop_conf_t iop_conf_tab[4][32] = {
 	/* PD18 */ {   0,   0,   0,   0,   0,   0   }, /* PD18 */
 	/* PD17 */ {   0,   0,   0,   0,   0,   0   }, /* PD17 */
 	/* PD16 */ {   0,   0,   0,   0,   0,   0   }, /* PD16 */
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
 	/* PD15 */ {   1,   0,   0,   1,   1,   1   }, /* I2C SDA */
 	/* PD14 */ {   1,   0,   0,   1,   1,   1   }, /* I2C SCL */
 #else
diff --git a/board/cpu87/cpu87.c b/board/cpu87/cpu87.c
index 057a34c2c3..7c591be870 100644
--- a/board/cpu87/cpu87.c
+++ b/board/cpu87/cpu87.c
@@ -163,7 +163,7 @@ const iop_conf_t iop_conf_tab[4][32] = {
 	/* PD18 */ {   0,   0,   0,   0,   0,   0   }, /* PD18 */
 	/* PD17 */ {   0,   0,   0,   0,   0,   0   }, /* PD17 */
 	/* PD16 */ {   0,   0,   0,   0,   0,   0   }, /* PD16 */
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
 	/* PD15 */ {   1,   0,   0,   1,   1,   1   }, /* I2C SDA */
 	/* PD14 */ {   1,   0,   0,   1,   1,   1   }, /* I2C SCL */
 #else
diff --git a/board/emk/top9000/top9000.c b/board/emk/top9000/top9000.c
index 86a8d0b566..c0609f0775 100644
--- a/board/emk/top9000/top9000.c
+++ b/board/emk/top9000/top9000.c
@@ -245,7 +245,7 @@ int board_eth_init(bd_t *bis)
  * However i2c_get_bus_num() cannot be called before
  * relocation.
  */
-#ifdef CONFIG_SOFT_I2C
+#ifdef CONFIG_SYS_I2C_SOFT
 void iic_init(void)
 {
 	/* ports are now initialized in board_early_init_f() */
@@ -253,7 +253,7 @@ void iic_init(void)
 
 int iic_read(void)
 {
-	switch ((gd->flags & GD_FLG_RELOC) ? i2c_get_bus_num() : 0) {
+	switch (I2C_ADAP_HWNR) {
 	case 0:
 		return at91_get_pio_value(I2C0_PORT, SDA0_PIN);
 	case 1:
@@ -264,7 +264,7 @@ int iic_read(void)
 
 void iic_sda(int bit)
 {
-	switch ((gd->flags & GD_FLG_RELOC) ? i2c_get_bus_num() : 0) {
+	switch (I2C_ADAP_HWNR) {
 	case 0:
 		at91_set_pio_value(I2C0_PORT, SDA0_PIN, bit);
 		break;
@@ -276,7 +276,7 @@ void iic_sda(int bit)
 
 void iic_scl(int bit)
 {
-	switch ((gd->flags & GD_FLG_RELOC) ? i2c_get_bus_num() : 0) {
+	switch (I2C_ADAP_HWNR) {
 	case 0:
 		at91_set_pio_value(I2C0_PORT, SCL0_PIN, bit);
 		break;
diff --git a/board/eukrea/cpuat91/cpuat91.c b/board/eukrea/cpuat91/cpuat91.c
index c74c3fc567..5dde2741ea 100644
--- a/board/eukrea/cpuat91/cpuat91.c
+++ b/board/eukrea/cpuat91/cpuat91.c
@@ -73,7 +73,7 @@ int board_eth_init(bd_t *bis)
 }
 #endif
 
-#ifdef CONFIG_SOFT_I2C
+#ifdef CONFIG_SYS_I2C_SOFT
 void i2c_init_board(void)
 {
 	u32 pin;
diff --git a/board/freescale/m52277evb/README b/board/freescale/m52277evb/README
index b6e955bcad..d5e7b05650 100644
--- a/board/freescale/m52277evb/README
+++ b/board/freescale/m52277evb/README
@@ -84,7 +84,7 @@ CONFIG_MCFPIT		-- define to use PIT timer
 
 CONFIG_FSL_I2C		-- define to use FSL common I2C driver
 CONFIG_HARD_I2C		-- define for I2C hardware support
-CONFIG_SOFT_I2C		-- define for I2C bit-banged
+CONFIG_SYS_I2C_SOFT	-- define for I2C bit-banged
 CONFIG_SYS_I2C_SPEED		-- define for I2C speed
 CONFIG_SYS_I2C_SLAVE		-- define for I2C slave address
 CONFIG_SYS_I2C_OFFSET		-- define for I2C base address offset
diff --git a/board/freescale/m53017evb/README b/board/freescale/m53017evb/README
index 64a3d42f0c..855bbd14e5 100644
--- a/board/freescale/m53017evb/README
+++ b/board/freescale/m53017evb/README
@@ -92,7 +92,7 @@ CONFIG_MCFPIT			-- define to use PIT timer
 
 CONFIG_FSL_I2C			-- define to use FSL common I2C driver
 CONFIG_HARD_I2C			-- define for I2C hardware support
-CONFIG_SOFT_I2C			-- define for I2C bit-banged
+CONFIG_SYS_I2C_SOFT		-- define for I2C bit-banged
 CONFIG_SYS_I2C_SPEED		-- define for I2C speed
 CONFIG_SYS_I2C_SLAVE		-- define for I2C slave address
 CONFIG_SYS_I2C_OFFSET		-- define for I2C base address offset
diff --git a/board/freescale/m5373evb/README b/board/freescale/m5373evb/README
index 419d4d6d1e..61e6d97b6d 100644
--- a/board/freescale/m5373evb/README
+++ b/board/freescale/m5373evb/README
@@ -91,7 +91,7 @@ CONFIG_MCFPIT		-- define to use PIT timer
 
 CONFIG_FSL_I2C		-- define to use FSL common I2C driver
 CONFIG_HARD_I2C		-- define for I2C hardware support
-CONFIG_SOFT_I2C		-- define for I2C bit-banged
+CONFIG_SYS_I2C_SOFT	-- define for I2C bit-banged
 CONFIG_SYS_I2C_SPEED		-- define for I2C speed
 CONFIG_SYS_I2C_SLAVE		-- define for I2C slave address
 CONFIG_SYS_I2C_OFFSET		-- define for I2C base address offset
diff --git a/board/freescale/m54455evb/README b/board/freescale/m54455evb/README
index 2bc6ce4bf3..2b25952398 100644
--- a/board/freescale/m54455evb/README
+++ b/board/freescale/m54455evb/README
@@ -114,7 +114,7 @@ CONFIG_MCFPIT		-- define to use PIT timer
 
 CONFIG_FSL_I2C		-- define to use FSL common I2C driver
 CONFIG_HARD_I2C		-- define for I2C hardware support
-CONFIG_SOFT_I2C		-- define for I2C bit-banged
+CONFIG_SYS_I2C_SOFT	-- define for I2C bit-banged
 CONFIG_SYS_I2C_SPEED		-- define for I2C speed
 CONFIG_SYS_I2C_SLAVE		-- define for I2C slave address
 CONFIG_SYS_I2C_OFFSET		-- define for I2C base address offset
diff --git a/board/freescale/m547xevb/README b/board/freescale/m547xevb/README
index d3aec20e4f..1a8cbce91d 100644
--- a/board/freescale/m547xevb/README
+++ b/board/freescale/m547xevb/README
@@ -99,7 +99,7 @@ CONFIG_SLTTMR		-- define to use SLT timer
 
 CONFIG_FSL_I2C		-- define to use FSL common I2C driver
 CONFIG_HARD_I2C		-- define for I2C hardware support
-CONFIG_SOFT_I2C		-- define for I2C bit-banged
+CONFIG_SYS_I2C_SOFT	-- define for I2C bit-banged
 CONFIG_SYS_I2C_SPEED		-- define for I2C speed
 CONFIG_SYS_I2C_SLAVE		-- define for I2C slave address
 CONFIG_SYS_I2C_OFFSET		-- define for I2C base address offset
diff --git a/board/ids8247/ids8247.c b/board/ids8247/ids8247.c
index 02db07f1db..541d7d65df 100644
--- a/board/ids8247/ids8247.c
+++ b/board/ids8247/ids8247.c
@@ -51,7 +51,7 @@ const iop_conf_t iop_conf_tab[4][32] = {
 	/* PA27 */ {   1,   1,	 1,   0,   0,	0   }, /* FCC1 RXDV */
 	/* PA26 */ {   1,   1,	 1,   0,   0,	0   }, /* FCC1 RXER */
 	/* PA25 */ {   0,   0,	 0,   0,   1,	0   }, /* 8247_P0 */
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
 	/* PA24 */ {   1,   0,	 0,   0,   1,	1   }, /* I2C_SDA2 */
 	/* PA23 */ {   1,   0,	 0,   1,   1,	1   }, /* I2C_SCL2 */
 #else /* normal I/O port pins */
diff --git a/board/keymile/common/ivm.c b/board/keymile/common/ivm.c
index 22d525602a..918a6ab639 100644
--- a/board/keymile/common/ivm.c
+++ b/board/keymile/common/ivm.c
@@ -318,10 +318,14 @@ int ivm_read_eeprom(void)
 	I2C_MUX_DEVICE *dev = NULL;
 #endif
 	uchar i2c_buffer[CONFIG_SYS_IVM_EEPROM_MAX_LEN];
-	uchar	*buf;
+	char	*buf;
 	unsigned long dev_addr = CONFIG_SYS_IVM_EEPROM_ADR;
 	int ret;
 
+#if defined(CONFIG_SYS_I2C)
+	buf = getenv("EEprom_ivm");
+	i2c_set_bus_num(buf ? (int)simple_strtol(buf, NULL, 10) : 0);
+#else
 #if defined(CONFIG_I2C_MUX)
 	/* First init the Bus, select the Bus */
 	buf = (unsigned char *) getenv("EEprom_ivm");
diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c
index b9448873c8..26551f8c44 100644
--- a/board/keymile/km_arm/km_arm.c
+++ b/board/keymile/km_arm/km_arm.c
@@ -63,7 +63,7 @@ static const u32 kwmpp_config[] = {
 	MPP5_NF_IO7,
 	MPP6_SYSRST_OUTn,
 	MPP7_PEX_RST_OUTn,
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
 	MPP8_GPIO,		/* SDA */
 	MPP9_GPIO,		/* SCL */
 #endif
@@ -234,7 +234,7 @@ int misc_init_r(void)
 
 int board_early_init_f(void)
 {
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
 	u32 tmp;
 
 	/* set the 2 bitbang i2c pins as output gpios */
@@ -260,7 +260,7 @@ int board_init(void)
 	kw_gpio_set_valid(KM_FLASH_GPIO_PIN, 1);
 	kw_gpio_direction_output(KM_FLASH_GPIO_PIN, 1);
 
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
 	/*
 	 * Reinit the GPIO for I2C Bitbang driver so that the now
 	 * available gpio framework is consistent. The calls to
@@ -440,7 +440,7 @@ int hush_init_var(void)
 }
 #endif
 
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
 void set_sda(int state)
 {
 	I2C_ACTIVE;
diff --git a/board/lwmon/lwmon.c b/board/lwmon/lwmon.c
index 34c6675fd8..85e09958bb 100644
--- a/board/lwmon/lwmon.c
+++ b/board/lwmon/lwmon.c
@@ -480,7 +480,7 @@ static void kbd_init (void)
 	uchar val, errcd;
 	int i;
 
-	i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+	i2c_set_bus_num(0);
 
 	gd->arch.kbd_status = 0;
 
diff --git a/board/lwmon/pcmcia.c b/board/lwmon/pcmcia.c
index acbb9d54d2..b9894cf011 100644
--- a/board/lwmon/pcmcia.c
+++ b/board/lwmon/pcmcia.c
@@ -104,7 +104,7 @@ int pcmcia_hardware_enable(int slot)
 
 	/*  switch VCC on */
 	val |= MAX1604_OP_SUS | MAX1604_VCCBON;
-	i2c_init  (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+	i2c_set_bus_num(0);
 	i2c_write (CONFIG_SYS_I2C_POWER_A_ADDR, 0, 0, &val, 1);
 
 	udelay(500000);
@@ -193,7 +193,7 @@ int pcmcia_voltage_set(int slot, int vcc, int vpp)
 	 */
 	debug ("PCMCIA power OFF\n");
 	val  = MAX1604_VCCBHIZ | MAX1604_VPPBHIZ;
-	i2c_init  (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+	i2c_set_bus_num(0);
 	i2c_write (CONFIG_SYS_I2C_POWER_A_ADDR, 0, 0, &val, 1);
 
 	val = 0;
diff --git a/board/pm826/pm826.c b/board/pm826/pm826.c
index 19e7a00028..17b4ac9ec7 100644
--- a/board/pm826/pm826.c
+++ b/board/pm826/pm826.c
@@ -169,7 +169,7 @@ const iop_conf_t iop_conf_tab[4][32] = {
 	/* PD18 */ {   0,   0,   0,   1,   0,   0   }, /* PD18 */
 	/* PD17 */ {   0,   1,   0,   0,   0,   0   }, /* PD17 */
 	/* PD16 */ {   0,   1,   0,   1,   0,   0   }, /* PD16 */
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
 	/* PD15 */ {   1,   0,   0,   1,   1,   1   }, /* I2C SDA */
 	/* PD14 */ {   1,   0,   0,   1,   1,   1   }, /* I2C SCL */
 #else
diff --git a/board/pm828/pm828.c b/board/pm828/pm828.c
index 4a3b2fd89b..5e68d4d39b 100644
--- a/board/pm828/pm828.c
+++ b/board/pm828/pm828.c
@@ -169,7 +169,7 @@ const iop_conf_t iop_conf_tab[4][32] = {
 	/* PD18 */ {   0,   0,   0,   1,   0,   0   }, /* PD18 */
 	/* PD17 */ {   0,   1,   0,   0,   0,   0   }, /* PD17 */
 	/* PD16 */ {   0,   1,   0,   1,   0,   0   }, /* PD16 */
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
 	/* PD15 */ {   1,   0,   0,   1,   1,   1   }, /* I2C SDA */
 	/* PD14 */ {   1,   0,   0,   1,   1,   1   }, /* I2C SCL */
 #else
diff --git a/board/sacsng/ioconfig.h b/board/sacsng/ioconfig.h
index be1ce7c835..ac8f152e1f 100644
--- a/board/sacsng/ioconfig.h
+++ b/board/sacsng/ioconfig.h
@@ -187,7 +187,7 @@ const iop_conf_t iop_conf_tab[4][32] = {
 	/* PD17 */ { CONF, SPEC,   1,  DOUT, ACTV,   0   }, /* SPI_MOSI       */
 	/* PD16 */ { CONF, SPEC,   1,  DIN,  ACTV,   0   }, /* SPI_MISO       */
 #endif
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
 	/* PD15 */ { CONF, GPIO,   0,  DOUT, OPEN,   1   }, /* I2C_SDA        */
 	/* PD14 */ { CONF, GPIO,   0,  DOUT, ACTV,   1   }, /* I2C_SCL        */
 #else
diff --git a/board/sandburst/karef/karef.c b/board/sandburst/karef/karef.c
index 6457f9b1f8..186998d1df 100644
--- a/board/sandburst/karef/karef.c
+++ b/board/sandburst/karef/karef.c
@@ -32,7 +32,6 @@
 #include <spd_sdram.h>
 #include <i2c.h>
 #include "../common/sb_common.h"
-#include "../common/ppc440gx_i2c.h"
 #if defined(CONFIG_HAS_ETH0) || defined(CONFIG_HAS_ETH1) || \
     defined(CONFIG_HAS_ETH2) || defined(CONFIG_HAS_ETH3)
 #include <net.h>
diff --git a/board/tqc/tqm8260/tqm8260.c b/board/tqc/tqm8260/tqm8260.c
index 65a3174ec6..867b9694e9 100644
--- a/board/tqc/tqm8260/tqm8260.c
+++ b/board/tqc/tqm8260/tqm8260.c
@@ -160,7 +160,7 @@ const iop_conf_t iop_conf_tab[4][32] = {
 	/* PD18 */ {   0,   0,   0,   1,   0,   0   }, /* PD19 */
 	/* PD17 */ {   0,   1,   0,   0,   0,   0   }, /* FCC1 ATMRXPRTY */
 	/* PD16 */ {   0,   1,   0,   1,   0,   0   }, /* FCC1 ATMTXPRTY */
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
 	/* PD15 */ {   1,   0,   0,   1,   1,   1   }, /* I2C SDA */
 	/* PD14 */ {   1,   0,   0,   1,   1,   1   }, /* I2C SCL */
 #else
diff --git a/board/tqc/tqm8272/tqm8272.c b/board/tqc/tqm8272/tqm8272.c
index 5aca227789..c874a7df8d 100644
--- a/board/tqc/tqm8272/tqm8272.c
+++ b/board/tqc/tqm8272/tqm8272.c
@@ -180,7 +180,7 @@ const iop_conf_t iop_conf_tab[4][32] = {
 	/* PD18 */ {   0,   0,	 0,   1,   0,	0   }, /* PD19 */
 	/* PD17 */ {   0,   1,	 0,   0,   0,	0   }, /* FCC1 ATMRXPRTY */
 	/* PD16 */ {   0,   1,	 0,   1,   0,	0   }, /* FCC1 ATMTXPRTY */
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
 	/* PD15 */ {   1,   0,	 0,   1,   1,	1   }, /* I2C SDA */
 	/* PD14 */ {   1,   0,	 0,   1,   1,	1   }, /* I2C SCL */
 #else
diff --git a/board/tqc/tqm8272/tqm8272.h b/board/tqc/tqm8272/tqm8272.h
index 6d558ec596..91b86c99d4 100644
--- a/board/tqc/tqm8272/tqm8272.h
+++ b/board/tqc/tqm8272/tqm8272.h
@@ -50,4 +50,4 @@ typedef struct{
 
 static HWIB_INFO	hwinf = {0, 0, 1, 0, 1, 0, 0, 0, 0, 8272, 0 ,0,
 			 0, 0, 0, 0, 0, 0};
-#endif
+#endif	/* __CONFIG_H */
diff --git a/common/board_f.c b/common/board_f.c
index ca9a7603ed..ddac2dfe09 100644
--- a/common/board_f.c
+++ b/common/board_f.c
@@ -261,8 +261,7 @@ void __dram_init_banksize(void)
 void dram_init_banksize(void)
 	__attribute__((weak, alias("__dram_init_banksize")));
 
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) || \
-	defined(CONFIG_SYS_I2C)
+#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C)
 static int init_func_i2c(void)
 {
 	puts("I2C:   ");
@@ -920,8 +919,7 @@ static init_fnc_t init_sequence_f[] = {
 	misc_init_f,
 #endif
 	INIT_FUNC_WATCHDOG_RESET
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) || \
-	defined(CONFIG_SYS_I2C)
+#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C)
 	init_func_i2c,
 #endif
 #if defined(CONFIG_HARD_SPI)
diff --git a/common/cmd_eeprom.c b/common/cmd_eeprom.c
index 4a43116e92..511d8b6022 100644
--- a/common/cmd_eeprom.c
+++ b/common/cmd_eeprom.c
@@ -406,8 +406,7 @@ void eeprom_init  (void)
 #if defined(CONFIG_SPI) && !defined(CONFIG_ENV_EEPROM_IS_ON_I2C)
 	spi_init_f ();
 #endif
-#if defined(CONFIG_HARD_I2C) || \
-    defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT)
 	i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
 #endif
 }
diff --git a/common/stdio.c b/common/stdio.c
index 2011880549..39eef5aa2e 100644
--- a/common/stdio.c
+++ b/common/stdio.c
@@ -34,8 +34,8 @@
 #ifdef CONFIG_LOGBUFFER
 #include <logbuff.h>
 #endif
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C) || \
-		defined(CONFIG_SYS_I2C_ADAPTERS)
+
+#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C)
 #include <i2c.h>
 #endif
 
@@ -216,11 +216,9 @@ int stdio_init (void)
 	drv_arm_dcc_init ();
 #endif
 #ifdef CONFIG_SYS_I2C
-#ifdef CONFIG_SYS_I2C_ADAPTERS
 	i2c_init_all();
-#endif
 #else
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_HARD_I2C)
 	i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
 #endif
 #endif
diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile
index 06b211d4a2..a885e26ce9 100644
--- a/drivers/i2c/Makefile
+++ b/drivers/i2c/Makefile
@@ -40,13 +40,13 @@ COBJS-$(CONFIG_PCA9564_I2C) += pca9564_i2c.o
 COBJS-$(CONFIG_PPC4XX_I2C) += ppc4xx_i2c.o
 COBJS-$(CONFIG_DRIVER_S3C24X0_I2C) += s3c24x0_i2c.o
 COBJS-$(CONFIG_S3C44B0_I2C) += s3c44b0_i2c.o
-COBJS-$(CONFIG_SOFT_I2C) += soft_i2c.o
 COBJS-$(CONFIG_TEGRA_I2C) += tegra_i2c.o
 COBJS-$(CONFIG_TSI108_I2C) += tsi108_i2c.o
 COBJS-$(CONFIG_U8500_I2C) += u8500_i2c.o
 COBJS-$(CONFIG_SH_I2C) += sh_i2c.o
 COBJS-$(CONFIG_SH_SH7734_I2C) += sh_sh7734_i2c.o
 COBJS-$(CONFIG_SYS_I2C) += i2c_core.o
+COBJS-$(CONFIG_SYS_I2C_SOFT) += soft_i2c.o
 COBJS-$(CONFIG_ZYNQ_I2C) += zynq_i2c.o
 
 COBJS	:= $(COBJS-y)
diff --git a/drivers/i2c/soft_i2c.c b/drivers/i2c/soft_i2c.c
index ae3c57392b..12693041d7 100644
--- a/drivers/i2c/soft_i2c.c
+++ b/drivers/i2c/soft_i2c.c
@@ -1,4 +1,8 @@
 /*
+ * (C) Copyright 2009
+ * Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ * Changes for multibus/multiadapter I2C support.
+ *
  * (C) Copyright 2001, 2002
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
@@ -103,14 +107,30 @@
 
 /* #define	DEBUG_I2C	*/
 
-#ifdef DEBUG_I2C
 DECLARE_GLOBAL_DATA_PTR;
+
+#ifndef	I2C_SOFT_DECLARATIONS
+# if defined(CONFIG_MPC8260)
+#  define I2C_SOFT_DECLARATIONS volatile ioport_t *iop = \
+		ioport_addr((immap_t *)CONFIG_SYS_IMMR, I2C_PORT);
+# elif defined(CONFIG_8xx)
+#  define I2C_SOFT_DECLARATIONS	volatile immap_t *immr = \
+		(immap_t *)CONFIG_SYS_IMMR;
+# else
+#  define I2C_SOFT_DECLARATIONS
+# endif
+#endif
+
+#if !defined(CONFIG_SYS_SOFT_I2C_SPEED)
+#define CONFIG_SYS_SOFT_I2C_SPEED CONFIG_SYS_I2C_SPEED
+#endif
+#if !defined(CONFIG_SYS_SOFT_I2C_SLAVE)
+#define CONFIG_SYS_SOFT_I2C_SLAVE CONFIG_SYS_I2C_SLAVE
 #endif
 
 /*-----------------------------------------------------------------------
  * Definitions
  */
-
 #define RETRIES		0
 
 #define I2C_ACK		0		/* PD_SDA level to ack a byte */
@@ -125,10 +145,6 @@ DECLARE_GLOBAL_DATA_PTR;
 #define PRINTD(fmt,args...)
 #endif
 
-#if defined(CONFIG_I2C_MULTI_BUS)
-static unsigned int i2c_bus_num __attribute__ ((section (".data"))) = 0;
-#endif /* CONFIG_I2C_MULTI_BUS */
-
 /*-----------------------------------------------------------------------
  * Local functions
  */
@@ -267,39 +283,6 @@ static int write_byte(uchar data)
 	return(nack);	/* not a nack is an ack */
 }
 
-#if defined(CONFIG_I2C_MULTI_BUS)
-/*
- * Functions for multiple I2C bus handling
- */
-unsigned int i2c_get_bus_num(void)
-{
-	return i2c_bus_num;
-}
-
-int i2c_set_bus_num(unsigned int bus)
-{
-#if defined(CONFIG_I2C_MUX)
-	if (bus < CONFIG_SYS_MAX_I2C_BUS) {
-		i2c_bus_num = bus;
-	} else {
-		int	ret;
-
-		ret = i2x_mux_select_mux(bus);
-		i2c_init_board();
-		if (ret == 0)
-			i2c_bus_num = bus;
-		else
-			return ret;
-	}
-#else
-	if (bus >= CONFIG_SYS_MAX_I2C_BUS)
-		return -1;
-	i2c_bus_num = bus;
-#endif
-	return 0;
-}
-#endif
-
 /*-----------------------------------------------------------------------
  * if ack == I2C_ACK, ACK the byte so can continue reading, else
  * send I2C_NOACK to end the read.
@@ -330,14 +313,10 @@ static uchar read_byte(int ack)
 	return(data);
 }
 
-/*=====================================================================*/
-/*                         Public Functions                            */
-/*=====================================================================*/
-
 /*-----------------------------------------------------------------------
  * Initialization
  */
-void i2c_init (int speed, int slaveaddr)
+static void soft_i2c_init(struct i2c_adapter *adap, int speed, int slaveaddr)
 {
 #if defined(CONFIG_SYS_I2C_INIT_BOARD)
 	/* call board specific i2c bus reset routine before accessing the   */
@@ -360,7 +339,7 @@ void i2c_init (int speed, int slaveaddr)
  * completion of EEPROM writes since the chip stops responding until
  * the write completes (typically 10mSec).
  */
-int i2c_probe(uchar addr)
+static int soft_i2c_probe(struct i2c_adapter *adap, uint8_t addr)
 {
 	int rc;
 
@@ -378,7 +357,8 @@ int i2c_probe(uchar addr)
 /*-----------------------------------------------------------------------
  * Read bytes
  */
-int  i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
+static int  soft_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr,
+			int alen, uchar *buffer, int len)
 {
 	int shift;
 	PRINTD("i2c_read: chip %02X addr %02X alen %d buffer %p len %d\n",
@@ -452,7 +432,8 @@ int  i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
 /*-----------------------------------------------------------------------
  * Write bytes
  */
-int  i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
+static int  soft_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr,
+			int alen, uchar *buffer, int len)
 {
 	int shift, failures = 0;
 
@@ -482,3 +463,32 @@ int  i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
 	send_stop();
 	return(failures);
 }
+
+/*
+ * Register soft i2c adapters
+ */
+U_BOOT_I2C_ADAP_COMPLETE(soft0, soft_i2c_init, soft_i2c_probe,
+			 soft_i2c_read, soft_i2c_write, NULL,
+			 CONFIG_SYS_I2C_SOFT_SPEED, CONFIG_SYS_I2C_SOFT_SLAVE,
+			 0)
+#if defined(I2C_SOFT_DECLARATIONS2)
+U_BOOT_I2C_ADAP_COMPLETE(soft1, soft_i2c_init, soft_i2c_probe,
+			 soft_i2c_read, soft_i2c_write, NULL,
+			 CONFIG_SYS_I2C_SOFT_SPEED_2,
+			 CONFIG_SYS_I2C_SOFT_SLAVE_2,
+			 1)
+#endif
+#if defined(I2C_SOFT_DECLARATIONS3)
+U_BOOT_I2C_ADAP_COMPLETE(soft2, soft_i2c_init, soft_i2c_probe,
+			 soft_i2c_read, soft_i2c_write, NULL,
+			 CONFIG_SYS_I2C_SOFT_SPEED_3,
+			 CONFIG_SYS_I2C_SOFT_SLAVE_3,
+			 2)
+#endif
+#if defined(I2C_SOFT_DECLARATIONS4)
+U_BOOT_I2C_ADAP_COMPLETE(soft3, soft_i2c_init, soft_i2c_probe,
+			 soft_i2c_read, soft_i2c_write, NULL,
+			 CONFIG_SYS_I2C_SOFT_SPEED_4,
+			 CONFIG_SYS_I2C_SOFT_SLAVE_4,
+			 3)
+#endif
diff --git a/include/configs/A3000.h b/include/configs/A3000.h
index d506a558c0..340c6851f9 100644
--- a/include/configs/A3000.h
+++ b/include/configs/A3000.h
@@ -86,8 +86,8 @@
  * PCI stuff
  *-----------------------------------------------------------------------
  */
-#define CONFIG_HARD_I2C		1		/* To enable I2C support	*/
-#undef	CONFIG_SOFT_I2C				/* I2C bit-banged		*/
+#define CONFIG_HARD_I2C		1		/* To enable I2C support */
+#undef	CONFIG_SYS_I2C_SOFT			/* I2C bit-banged */
 #define CONFIG_SYS_I2C_SPEED		400000		/* I2C speed and slave address	*/
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 
diff --git a/include/configs/BSC9131RDB.h b/include/configs/BSC9131RDB.h
index b5911c6945..a3f64408de 100644
--- a/include/configs/BSC9131RDB.h
+++ b/include/configs/BSC9131RDB.h
@@ -277,7 +277,6 @@ extern unsigned long get_sdram_size(void);
 
 #define CONFIG_FSL_I2C			/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C			/* I2C with hardware support */
-#undef CONFIG_SOFT_I2C			/* I2C bit-banged */
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_I2C_CMD_TREE
 #define CONFIG_SYS_I2C_SPEED		400000 /* I2C speed and slave address*/
diff --git a/include/configs/CANBT.h b/include/configs/CANBT.h
index be9238e520..fd3eff0c1f 100644
--- a/include/configs/CANBT.h
+++ b/include/configs/CANBT.h
@@ -180,6 +180,7 @@
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC08) for environment
  */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address	*/
 #define CONFIG_HARD_I2C			/* I2C with hardware support */
 #define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
diff --git a/include/configs/CPU86.h b/include/configs/CPU86.h
index 7ac182f0f0..43b07cf46b 100644
--- a/include/configs/CPU86.h
+++ b/include/configs/CPU86.h
@@ -129,10 +129,11 @@
 /*-----------------------------------------------------------------------
  * I2C/EEPROM/RTC configuration
  */
-#define	CONFIG_SOFT_I2C			/* Software I2C support enabled	*/
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT			/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 
-# define CONFIG_SYS_I2C_SPEED		50000
-# define CONFIG_SYS_I2C_SLAVE		0xFE
 /*
  * Software (bit-bang) I2C driver configuration
  */
diff --git a/include/configs/CPU87.h b/include/configs/CPU87.h
index 3e9c21cc9d..9c3b3d5b40 100644
--- a/include/configs/CPU87.h
+++ b/include/configs/CPU87.h
@@ -133,10 +133,11 @@
 /*-----------------------------------------------------------------------
  * I2C/EEPROM/RTC configuration
  */
-#define CONFIG_SOFT_I2C			/* Software I2C support enabled */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 
-# define CONFIG_SYS_I2C_SPEED		50000
-# define CONFIG_SYS_I2C_SLAVE		0xFE
 /*
  * Software (bit-bang) I2C driver configuration
  */
diff --git a/include/configs/DU440.h b/include/configs/DU440.h
index 4970ea657b..152821f567 100644
--- a/include/configs/DU440.h
+++ b/include/configs/DU440.h
@@ -171,7 +171,6 @@
  * I2C
  */
 #define CONFIG_HARD_I2C		1	/* I2C with hardware support    */
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged	        */
 #define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
 #define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed and slave address  */
 #define CONFIG_SYS_I2C_SLAVE		0x7F
diff --git a/include/configs/GEN860T.h b/include/configs/GEN860T.h
index 9a649ca125..cc03d397d3 100644
--- a/include/configs/GEN860T.h
+++ b/include/configs/GEN860T.h
@@ -158,26 +158,33 @@
 /*
  * Enable I2C and select the hardware/software driver
  */
-#define CONFIG_HARD_I2C		1				/* CPM based I2C			*/
-#undef	CONFIG_SOFT_I2C						/* Bit-banged I2C			*/
+#define CONFIG_HARD_I2C		1		/* CPM based I2C */
+#undef	CONFIG_SYS_I2C_SOFT			/* Bit-banged I2C */
 
 #ifdef CONFIG_HARD_I2C
-#define	CONFIG_SYS_I2C_SPEED		100000			/* clock speed in Hz		*/
-#define CONFIG_SYS_I2C_SLAVE		0xFE			/* I2C slave address		*/
+#define	CONFIG_SYS_I2C_SPEED		100000	/* clock speed in Hz */
+#define CONFIG_SYS_I2C_SLAVE		0xFE	/* I2C slave address */
 #endif
 
-#ifdef CONFIG_SOFT_I2C
-#define PB_SCL				0x00000020		/* PB 26					*/
-#define PB_SDA				0x00000010		/* PB 27					*/
-#define I2C_INIT			(immr->im_cpm.cp_pbdir |=  PB_SCL)
-#define I2C_ACTIVE			(immr->im_cpm.cp_pbdir |=  PB_SDA)
-#define I2C_TRISTATE		(immr->im_cpm.cp_pbdir &= ~PB_SDA)
-#define I2C_READ			((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
-#define I2C_SDA(bit)		if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
-								else    immr->im_cpm.cp_pbdat &= ~PB_SDA
-#define I2C_SCL(bit)		if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
-								else    immr->im_cpm.cp_pbdat &= ~PB_SCL
-#define I2C_DELAY			udelay(5)		/* 1/4 I2C clock duration	*/
+#ifdef CONFIG_SYS_I2C_SOFT
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
+#define PB_SCL		0x00000020		/* PB 26 */
+#define PB_SDA		0x00000010		/* PB 27 */
+#define I2C_INIT	(immr->im_cpm.cp_pbdir |=  PB_SCL)
+#define I2C_ACTIVE	(immr->im_cpm.cp_pbdir |=  PB_SDA)
+#define I2C_TRISTATE	(immr->im_cpm.cp_pbdir &= ~PB_SDA)
+#define I2C_READ	((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
+#define I2C_SDA(bit)	if (bit) \
+				immr->im_cpm.cp_pbdat |=  PB_SDA; \
+			else \
+				immr->im_cpm.cp_pbdat &= ~PB_SDA
+#define I2C_SCL(bit)	if (bit) \
+				immr->im_cpm.cp_pbdat |=  PB_SCL; \
+			else \
+				immr->im_cpm.cp_pbdat &= ~PB_SCL
+#define I2C_DELAY	udelay(5) /* 1/4 I2C clock duration */
 #endif
 
 /*
diff --git a/include/configs/HIDDEN_DRAGON.h b/include/configs/HIDDEN_DRAGON.h
index dbad1fd6af..071b4be737 100644
--- a/include/configs/HIDDEN_DRAGON.h
+++ b/include/configs/HIDDEN_DRAGON.h
@@ -169,12 +169,15 @@
  * configuration items that the driver uses to drive the port pins.
  */
 #define CONFIG_HARD_I2C		1		/* To enable I2C support	*/
-#undef	CONFIG_SOFT_I2C				/* I2C bit-banged		*/
+#undef	CONFIG_SYS_I2C_SOFT			/* I2C bit-banged */
 #define CONFIG_SYS_I2C_SPEED		400000		/* I2C speed and slave address	*/
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 
-#ifdef CONFIG_SOFT_I2C
+#ifdef CONFIG_SYS_I2C_SOFT
 #error "Soft I2C is not configured properly.  Please review!"
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 #define I2C_PORT		3		/* Port A=0, B=1, C=2, D=3 */
 #define I2C_ACTIVE		(iop->pdir |=  0x00010000)
 #define I2C_TRISTATE		(iop->pdir &= ~0x00010000)
@@ -184,7 +187,7 @@
 #define I2C_SCL(bit)		if(bit) iop->pdat |=  0x00020000; \
 				else	iop->pdat &= ~0x00020000
 #define I2C_DELAY		udelay(5)	/* 1/4 I2C clock duration */
-#endif /* CONFIG_SOFT_I2C */
+#endif /* CONFIG_SYS_I2C_SOFT */
 
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x57		/* EEPROM IS24C02		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1		/* Bytes of address		*/
diff --git a/include/configs/ICU862.h b/include/configs/ICU862.h
index b58b6f638c..ca8138bf05 100644
--- a/include/configs/ICU862.h
+++ b/include/configs/ICU862.h
@@ -106,12 +106,10 @@
 #define CONFIG_DOS_PARTITION
 
 /* enable I2C and select the hardware/software driver */
-#undef  CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
-# define CONFIG_SYS_I2C_SPEED		50000
-# define CONFIG_SYS_I2C_SLAVE		0xFE
-# define CONFIG_SYS_I2C_EEPROM_ADDR	0x50
-# define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 /*
  * Software (bit-bang) I2C driver configuration
  */
@@ -133,6 +131,9 @@
 
 #define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
 
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address */
+
 
 /*
  * Command line configuration.
diff --git a/include/configs/IDS8247.h b/include/configs/IDS8247.h
index 6d0937fb34..b5a8d37e71 100644
--- a/include/configs/IDS8247.h
+++ b/include/configs/IDS8247.h
@@ -73,11 +73,10 @@
 #define CONFIG_MISC_INIT_R	1
 
 /* enable I2C and select the hardware/software driver */
-#undef  CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	400000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0x7F
 /*
  * Software (bit-bang) I2C driver configuration
  */
diff --git a/include/configs/IP860.h b/include/configs/IP860.h
index 2379718565..e5cc4e389b 100644
--- a/include/configs/IP860.h
+++ b/include/configs/IP860.h
@@ -62,8 +62,10 @@
 
 
 /* enable I2C and select the hardware/software driver */
-#undef  CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 /*
  * Software (bit-bang) I2C driver configuration
  */
@@ -80,9 +82,6 @@
 			else    immr->im_cpm.cp_pbdat &= ~PB_SCL
 #define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
 
-
-# define CONFIG_SYS_I2C_SPEED		50000
-# define CONFIG_SYS_I2C_SLAVE		0xFE
 # define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM X24C16		*/
 # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* bytes of address		*/
 /* mask of address bits that overflow into the "EEPROM chip address"    */
diff --git a/include/configs/IPHASE4539.h b/include/configs/IPHASE4539.h
index 6dd98128d4..b1fec10b22 100644
--- a/include/configs/IPHASE4539.h
+++ b/include/configs/IPHASE4539.h
@@ -110,15 +110,13 @@
  * If the software driver is chosen, there are some additional
  * configuration items that the driver uses to drive the port pins.
  */
-#undef  CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	400000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0x7F
 /*
  * Software (bit-bang) I2C driver configuration
  */
-#ifdef CONFIG_SOFT_I2C
 #define I2C_PORT	3		/* Port A=0, B=1, C=2, D=3 */
 #define I2C_ACTIVE	(iop->pdir |=  0x00010000)
 #define I2C_TRISTATE	(iop->pdir &= ~0x00010000)
@@ -128,7 +126,6 @@
 #define I2C_SCL(bit)	if(bit) iop->pdat |=  0x00020000; \
 			else    iop->pdat &= ~0x00020000
 #define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
-#endif /* CONFIG_SOFT_I2C */
 
 
 /*
diff --git a/include/configs/JSE.h b/include/configs/JSE.h
index 6ce789d7fa..76509be048 100644
--- a/include/configs/JSE.h
+++ b/include/configs/JSE.h
@@ -211,7 +211,6 @@
 #define CONFIG_SYS_HZ		1000		/* decrementer freq: 1 ms ticks */
 
 #define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
 #define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
 #define CONFIG_SYS_I2C_SLAVE		0x7F
diff --git a/include/configs/KAREF.h b/include/configs/KAREF.h
index 8d5e8ff653..5736fcfa10 100644
--- a/include/configs/KAREF.h
+++ b/include/configs/KAREF.h
@@ -134,7 +134,6 @@
  * I2C
  *----------------------------------------------------------------------*/
 #define CONFIG_HARD_I2C	      1		     /* I2C hardware support	*/
-#undef	CONFIG_SOFT_I2C			     /* I2C !bit-banged		*/
 #define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
 #define CONFIG_SYS_I2C_SPEED	      400000	     /* I2C speed 400kHz	*/
 #define CONFIG_SYS_I2C_SLAVE	      0x7F	     /* I2C slave address	*/
diff --git a/include/configs/KUP4K.h b/include/configs/KUP4K.h
index dae9b8c079..d6f3a628ef 100644
--- a/include/configs/KUP4K.h
+++ b/include/configs/KUP4K.h
@@ -106,13 +106,11 @@
 /*
  * enable I2C and select the hardware/software driver
  */
-#undef	CONFIG_HARD_I2C		/* I2C with hardware support	*/
-#define	CONFIG_SOFT_I2C		/* I2C bit-banged		*/
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	93000	/* 93 kHz is supposed to work */
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 
-#define CONFIG_SYS_I2C_SPEED	93000	/* 93 kHz is supposed to work */
-#define CONFIG_SYS_I2C_SLAVE	0xFE
-
-#ifdef CONFIG_SOFT_I2C
 /*
  * Software (bit-bang) I2C driver configuration
  */
@@ -128,7 +126,6 @@
 #define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
 			else    immr->im_cpm.cp_pbdat &= ~PB_SCL
 #define I2C_DELAY	udelay(2)	/* 1/4 I2C clock duration */
-#endif	/* CONFIG_SOFT_I2C */
 
 /*-----------------------------------------------------------------------
  * I2C Configuration
diff --git a/include/configs/KUP4X.h b/include/configs/KUP4X.h
index cceee96742..247374922d 100644
--- a/include/configs/KUP4X.h
+++ b/include/configs/KUP4X.h
@@ -114,13 +114,13 @@
 /*
  * enable I2C and select the hardware/software driver
  */
-#undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define	CONFIG_SOFT_I2C         1	/* I2C bit-banged		*/
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
 
-#define CONFIG_SYS_I2C_SPEED		93000	/* 93 kHz is supposed to work	*/
-#define CONFIG_SYS_I2C_SLAVE		0xFE
+#ifdef CONFIG_SYS_I2C_SOFT
+#define CONFIG_SYS_I2C_SOFT_SPEED	93000	/* 93 kHz is supposed to work */
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 
-#ifdef CONFIG_SOFT_I2C
 /*
  * Software (bit-bang) I2C driver configuration
  */
@@ -136,7 +136,7 @@
 #define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
 			else    immr->im_cpm.cp_pbdat &= ~PB_SCL
 #define I2C_DELAY	udelay(2)	/* 1/4 I2C clock duration */
-#endif	/* CONFIG_SOFT_I2C */
+#endif	/* CONFIG_SYS_I2C_SOFT */
 
 
 /*-----------------------------------------------------------------------
diff --git a/include/configs/M5208EVBE.h b/include/configs/M5208EVBE.h
index a1eaeff80e..209c1223f4 100644
--- a/include/configs/M5208EVBE.h
+++ b/include/configs/M5208EVBE.h
@@ -84,7 +84,6 @@
 /* I2C */
 #define CONFIG_FSL_I2C
 #define CONFIG_HARD_I2C			/* I2C with hw support */
-#undef CONFIG_SOFT_I2C			/* I2C bit-banged */
 #define CONFIG_SYS_I2C_SPEED		80000
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #define CONFIG_SYS_I2C_OFFSET		0x58000
diff --git a/include/configs/M52277EVB.h b/include/configs/M52277EVB.h
index e4dea05ea7..b1bdac2d7b 100644
--- a/include/configs/M52277EVB.h
+++ b/include/configs/M52277EVB.h
@@ -147,7 +147,6 @@
 /* I2c */
 #define CONFIG_FSL_I2C
 #define CONFIG_HARD_I2C		/* I2C with hardware support */
-#undef	CONFIG_SOFT_I2C		/* I2C bit-banged               */
 #define CONFIG_SYS_I2C_SPEED		80000	/* I2C speed and slave address  */
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #define CONFIG_SYS_I2C_OFFSET		0x58000
diff --git a/include/configs/M5235EVB.h b/include/configs/M5235EVB.h
index 733aece767..dfc2ddf35d 100644
--- a/include/configs/M5235EVB.h
+++ b/include/configs/M5235EVB.h
@@ -101,7 +101,6 @@
 /* I2C */
 #define CONFIG_FSL_I2C
 #define CONFIG_HARD_I2C		/* I2C with hw support */
-#undef CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_SYS_I2C_SPEED		80000
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #define CONFIG_SYS_I2C_OFFSET		0x00000300
diff --git a/include/configs/M5271EVB.h b/include/configs/M5271EVB.h
index a5913df2cb..e8a8998fcc 100644
--- a/include/configs/M5271EVB.h
+++ b/include/configs/M5271EVB.h
@@ -111,7 +111,6 @@
 /* I2C */
 #define CONFIG_FSL_I2C
 #define CONFIG_HARD_I2C		/* I2C with hw support */
-#undef CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_SYS_I2C_SPEED		80000
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #define CONFIG_SYS_I2C_OFFSET		0x00000300
diff --git a/include/configs/M5275EVB.h b/include/configs/M5275EVB.h
index 9c2a3bbb91..fbf0c9d9ac 100644
--- a/include/configs/M5275EVB.h
+++ b/include/configs/M5275EVB.h
@@ -111,7 +111,6 @@
 /* I2C */
 #define CONFIG_FSL_I2C
 #define CONFIG_HARD_I2C		/* I2C with hw support */
-#undef CONFIG_SOFT_I2C
 #define CONFIG_SYS_I2C_SPEED		80000
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #define CONFIG_SYS_I2C_OFFSET		0x00000300
diff --git a/include/configs/M53017EVB.h b/include/configs/M53017EVB.h
index 896d0d8536..bedba2b290 100644
--- a/include/configs/M53017EVB.h
+++ b/include/configs/M53017EVB.h
@@ -103,7 +103,6 @@
 /* I2C */
 #define CONFIG_FSL_I2C
 #define CONFIG_HARD_I2C			/* I2C with hw support */
-#undef CONFIG_SOFT_I2C			/* I2C bit-banged */
 #define CONFIG_SYS_I2C_SPEED		80000
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #define CONFIG_SYS_I2C_OFFSET		0x58000
diff --git a/include/configs/M5329EVB.h b/include/configs/M5329EVB.h
index 64f83026c4..06fa57cc02 100644
--- a/include/configs/M5329EVB.h
+++ b/include/configs/M5329EVB.h
@@ -97,7 +97,6 @@
 /* I2C */
 #define CONFIG_FSL_I2C
 #define CONFIG_HARD_I2C			/* I2C with hw support */
-#undef CONFIG_SOFT_I2C			/* I2C bit-banged */
 #define CONFIG_SYS_I2C_SPEED		80000
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #define CONFIG_SYS_I2C_OFFSET		0x58000
diff --git a/include/configs/M5373EVB.h b/include/configs/M5373EVB.h
index 4437bbae86..faa4f86e43 100644
--- a/include/configs/M5373EVB.h
+++ b/include/configs/M5373EVB.h
@@ -97,7 +97,6 @@
 /* I2C */
 #define CONFIG_FSL_I2C
 #define CONFIG_HARD_I2C		/* I2C with hw support */
-#undef CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_SYS_I2C_SPEED		80000
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #define CONFIG_SYS_I2C_OFFSET		0x58000
diff --git a/include/configs/M54418TWR.h b/include/configs/M54418TWR.h
index 3be2f8ef33..627c1ae005 100644
--- a/include/configs/M54418TWR.h
+++ b/include/configs/M54418TWR.h
@@ -215,7 +215,7 @@
 /* I2c */
 #undef CONFIG_FSL_I2C
 #undef CONFIG_HARD_I2C		/* I2C with hardware support */
-#undef	CONFIG_SOFT_I2C		/* I2C bit-banged */
+#undef	CONFIG_SYS_I2C_SOFT	/* I2C bit-banged */
 /* I2C speed and slave address  */
 #define CONFIG_SYS_I2C_SPEED		80000
 #define CONFIG_SYS_I2C_SLAVE		0x7F
diff --git a/include/configs/M54451EVB.h b/include/configs/M54451EVB.h
index 6552f69cc8..5dbe0b47c1 100644
--- a/include/configs/M54451EVB.h
+++ b/include/configs/M54451EVB.h
@@ -158,7 +158,6 @@
 /* I2c */
 #define CONFIG_FSL_I2C
 #define CONFIG_HARD_I2C		/* I2C with hardware support */
-#undef	CONFIG_SOFT_I2C		/* I2C bit-banged               */
 #define CONFIG_SYS_I2C_SPEED		80000	/* I2C speed and slave address  */
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #define CONFIG_SYS_I2C_OFFSET		0x58000
diff --git a/include/configs/M54455EVB.h b/include/configs/M54455EVB.h
index 536b7556fa..8246e68e46 100644
--- a/include/configs/M54455EVB.h
+++ b/include/configs/M54455EVB.h
@@ -191,7 +191,6 @@
 /* I2c */
 #define CONFIG_FSL_I2C
 #define CONFIG_HARD_I2C		/* I2C with hardware support */
-#undef	CONFIG_SOFT_I2C		/* I2C bit-banged               */
 #define CONFIG_SYS_I2C_SPEED		80000	/* I2C speed and slave address  */
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #define CONFIG_SYS_I2C_OFFSET		0x58000
diff --git a/include/configs/M5475EVB.h b/include/configs/M5475EVB.h
index 3bdb8673c6..6e9cba00a7 100644
--- a/include/configs/M5475EVB.h
+++ b/include/configs/M5475EVB.h
@@ -122,7 +122,6 @@
 /* I2C */
 #define CONFIG_FSL_I2C
 #define CONFIG_HARD_I2C		/* I2C with hw support */
-#undef CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_SYS_I2C_SPEED		80000
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #define CONFIG_SYS_I2C_OFFSET		0x00008F00
diff --git a/include/configs/M5485EVB.h b/include/configs/M5485EVB.h
index 3487e49a1c..24f28e0ff5 100644
--- a/include/configs/M5485EVB.h
+++ b/include/configs/M5485EVB.h
@@ -119,7 +119,6 @@
 /* I2C */
 #define CONFIG_FSL_I2C
 #define CONFIG_HARD_I2C		/* I2C with hw support */
-#undef CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_SYS_I2C_SPEED		80000
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #define CONFIG_SYS_I2C_OFFSET		0x00008F00
diff --git a/include/configs/METROBOX.h b/include/configs/METROBOX.h
index d1ef559cf4..66c4798b5f 100644
--- a/include/configs/METROBOX.h
+++ b/include/configs/METROBOX.h
@@ -196,7 +196,6 @@
  * I2C
  *----------------------------------------------------------------------*/
 #define CONFIG_HARD_I2C	      1		     /* I2C hardware support	*/
-#undef	CONFIG_SOFT_I2C			     /* I2C !bit-banged		*/
 #define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
 #define CONFIG_SYS_I2C_SPEED	      400000	     /* I2C speed 400kHz	*/
 #define CONFIG_SYS_I2C_SLAVE	      0x7F	     /* I2C slave address	*/
diff --git a/include/configs/MHPC.h b/include/configs/MHPC.h
index 3ff36ad2a6..fdd811d77f 100644
--- a/include/configs/MHPC.h
+++ b/include/configs/MHPC.h
@@ -73,8 +73,10 @@
 #undef	CONFIG_UCODE_PATCH
 
 /* enable I2C and select the hardware/software driver */
-#undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 /*
  * Software (bit-bang) I2C driver configuration
  */
@@ -91,8 +93,6 @@
 			else	immr->im_cpm.cp_pbdat &= ~PB_SCL
 #define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
 
-#define CONFIG_SYS_I2C_SPEED			50000
-#define CONFIG_SYS_I2C_SLAVE			0xFE
 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x50	/* EEPROM X24C04		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1	/* bytes of address		*/
 /* mask of address bits that overflow into the "EEPROM chip address"	*/
diff --git a/include/configs/MPC8323ERDB.h b/include/configs/MPC8323ERDB.h
index ac4c253968..d32b14a105 100644
--- a/include/configs/MPC8323ERDB.h
+++ b/include/configs/MPC8323ERDB.h
@@ -234,7 +234,6 @@
 
 /* I2C */
 #define CONFIG_HARD_I2C		/* I2C with hardware support */
-#undef CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_FSL_I2C
 #define CONFIG_SYS_I2C_SPEED	400000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_SLAVE	0x7F
diff --git a/include/configs/MPC832XEMDS.h b/include/configs/MPC832XEMDS.h
index 7c31f47953..a35c6b6d84 100644
--- a/include/configs/MPC832XEMDS.h
+++ b/include/configs/MPC832XEMDS.h
@@ -327,7 +327,6 @@
 
 /* I2C */
 #define CONFIG_HARD_I2C		/* I2C with hardware support */
-#undef CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_FSL_I2C
 #define CONFIG_SYS_I2C_SPEED	400000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_SLAVE	0x7F
diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h
index 212089c238..7c3f35c3af 100644
--- a/include/configs/MPC8349EMDS.h
+++ b/include/configs/MPC8349EMDS.h
@@ -355,7 +355,6 @@
 
 /* I2C */
 #define CONFIG_HARD_I2C		/* I2C with hardware support*/
-#undef CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_FSL_I2C
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_SYS_I2C_SPEED	400000	/* I2C speed and slave address */
diff --git a/include/configs/MPC8349ITX.h b/include/configs/MPC8349ITX.h
index 1130b59a21..c67ffdba0f 100644
--- a/include/configs/MPC8349ITX.h
+++ b/include/configs/MPC8349ITX.h
@@ -131,8 +131,6 @@
 #define I2C_8574_PCI66		0x20	/* 0=33MHz PCI, 1=66MHz PCI */
 #define I2C_8574_FLASHSIDE	0x40	/* 0=Reset vector from U4, 1=from U7*/
 
-#undef CONFIG_SOFT_I2C
-
 #endif
 
 /* Compact Flash */
diff --git a/include/configs/MPC8360EMDS.h b/include/configs/MPC8360EMDS.h
index a71ac2bd35..4d6486bb30 100644
--- a/include/configs/MPC8360EMDS.h
+++ b/include/configs/MPC8360EMDS.h
@@ -424,7 +424,6 @@
 
 /* I2C */
 #define CONFIG_HARD_I2C		/* I2C with hardware support */
-#undef	CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_FSL_I2C
 #define CONFIG_SYS_I2C_SPEED	400000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_SLAVE	0x7F
diff --git a/include/configs/MPC8360ERDK.h b/include/configs/MPC8360ERDK.h
index fcca5424e3..29e77195de 100644
--- a/include/configs/MPC8360ERDK.h
+++ b/include/configs/MPC8360ERDK.h
@@ -288,7 +288,6 @@
 
 /* I2C */
 #define CONFIG_HARD_I2C		/* I2C with hardware support */
-#undef	CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_FSL_I2C
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_SYS_I2C_SPEED	400000	/* I2C speed and slave address */
diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h
index 480468f2d7..91c8a34859 100644
--- a/include/configs/MPC837XEMDS.h
+++ b/include/configs/MPC837XEMDS.h
@@ -342,7 +342,6 @@
 
 /* I2C */
 #define CONFIG_HARD_I2C		/* I2C with hardware support */
-#undef CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_FSL_I2C
 #define CONFIG_SYS_I2C_SPEED	400000 /* I2C speed and slave address */
 #define CONFIG_SYS_I2C_SLAVE	0x7F
diff --git a/include/configs/MPC837XERDB.h b/include/configs/MPC837XERDB.h
index d5c9d059eb..3279e3cf6f 100644
--- a/include/configs/MPC837XERDB.h
+++ b/include/configs/MPC837XERDB.h
@@ -368,7 +368,6 @@
 
 /* I2C */
 #define CONFIG_HARD_I2C		/* I2C with hardware support */
-#undef	CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_FSL_I2C
 #define CONFIG_SYS_I2C_SPEED	400000 /* I2C speed and slave address */
 #define CONFIG_SYS_I2C_SLAVE	0x7F
diff --git a/include/configs/MPC8536DS.h b/include/configs/MPC8536DS.h
index cc2b7c332b..f560b56d46 100644
--- a/include/configs/MPC8536DS.h
+++ b/include/configs/MPC8536DS.h
@@ -436,7 +436,6 @@
  */
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C		/* I2C with hardware support */
-#undef	CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_SLAVE		0x7F
diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h
index 6cb00ee664..a42dec4ed8 100644
--- a/include/configs/MPC8540ADS.h
+++ b/include/configs/MPC8540ADS.h
@@ -262,7 +262,6 @@
  */
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C		/* I2C with hardware support*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #define CONFIG_SYS_I2C_NOPROBES        {0x69}	/* Don't probe these addrs */
diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h
index d0e6ca65bf..13011b5a87 100644
--- a/include/configs/MPC8541CDS.h
+++ b/include/configs/MPC8541CDS.h
@@ -285,7 +285,6 @@ extern unsigned long get_clock_freq(void);
  */
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C		/* I2C with hardware support*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #define CONFIG_SYS_I2C_NOPROBES        {0x69}	/* Don't probe these addrs */
diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h
index 09d0835c61..b00468eb8b 100644
--- a/include/configs/MPC8544DS.h
+++ b/include/configs/MPC8544DS.h
@@ -234,7 +234,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /* I2C */
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C		/* I2C with hardware support */
-#undef	CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x57
 #define CONFIG_SYS_I2C_SLAVE		0x7F
diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h
index d070f6adc3..50e318c5d6 100644
--- a/include/configs/MPC8548CDS.h
+++ b/include/configs/MPC8548CDS.h
@@ -360,8 +360,7 @@ extern unsigned long get_clock_freq(void);
  */
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C		/* I2C with hardware support*/
-#undef	CONFIG_SOFT_I2C		/* I2C bit-banged */
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SPEED		400000
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #define CONFIG_SYS_I2C_NOPROBES	{0x69}	/* Don't probe these addrs */
 #define CONFIG_SYS_I2C_OFFSET		0x3000
diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h
index 483556b31b..388ba9ba1e 100644
--- a/include/configs/MPC8555CDS.h
+++ b/include/configs/MPC8555CDS.h
@@ -283,7 +283,6 @@ extern unsigned long get_clock_freq(void);
  */
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C		/* I2C with hardware support*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #define CONFIG_SYS_I2C_NOPROBES        {0x69}	/* Don't probe these addrs */
diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index 525e88fa1b..04f6a656e6 100644
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -256,7 +256,6 @@
  */
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C		/* I2C with hardware support*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #define CONFIG_SYS_I2C_NOPROBES        {0x69}	/* Don't probe these addrs */
diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
index f1bfdcbd2c..05a69af6ae 100644
--- a/include/configs/MPC8568MDS.h
+++ b/include/configs/MPC8568MDS.h
@@ -268,7 +268,6 @@ extern unsigned long get_clock_freq(void);
  */
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C		/* I2C with hardware support*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x52
diff --git a/include/configs/MPC8569MDS.h b/include/configs/MPC8569MDS.h
index c54755fab8..23bd90880a 100644
--- a/include/configs/MPC8569MDS.h
+++ b/include/configs/MPC8569MDS.h
@@ -304,7 +304,6 @@ extern unsigned long get_clock_freq(void);
  */
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C		/* I2C with hardware support*/
-#undef	CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_SYS_I2C_SPEED	400000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_SLAVE	0x7F
diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h
index 25303c4f65..45abcf61de 100644
--- a/include/configs/MPC8572DS.h
+++ b/include/configs/MPC8572DS.h
@@ -433,7 +433,6 @@
 /* I2C */
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C		/* I2C with hardware support */
-#undef	CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x57
diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h
index f791e7682e..0a2e39b118 100644
--- a/include/configs/MPC8610HPCD.h
+++ b/include/configs/MPC8610HPCD.h
@@ -254,7 +254,6 @@
  */
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C		/* I2C with hardware support*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #define CONFIG_SYS_I2C_NOPROBES	{0x69}	/* Don't probe these addrs */
diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h
index 4a3ca017e8..3ac5b2beb1 100644
--- a/include/configs/MPC8641HPCN.h
+++ b/include/configs/MPC8641HPCN.h
@@ -300,7 +300,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  */
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C		/* I2C with hardware support*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #define CONFIG_SYS_I2C_NOPROBES	{0x69}	/* Don't probe these addrs */
diff --git a/include/configs/P1010RDB.h b/include/configs/P1010RDB.h
index 7b28a27bc0..ed1a42916d 100644
--- a/include/configs/P1010RDB.h
+++ b/include/configs/P1010RDB.h
@@ -491,7 +491,6 @@ extern unsigned long get_sdram_size(void);
 
 #define CONFIG_FSL_I2C			/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C			/* I2C with hardware support */
-#undef CONFIG_SOFT_I2C			/* I2C bit-banged */
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_I2C_CMD_TREE
 #define CONFIG_SYS_I2C_SPEED		400000 /* I2C speed and slave address*/
diff --git a/include/configs/P1023RDS.h b/include/configs/P1023RDS.h
index 4943d7c8fe..f6ee2515a3 100644
--- a/include/configs/P1023RDS.h
+++ b/include/configs/P1023RDS.h
@@ -315,7 +315,6 @@ extern unsigned long get_clock_freq(void);
 /* I2C */
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C		/* I2C with hardware support */
-#undef	CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_SYS_I2C_SPEED	400000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x51
diff --git a/include/configs/P1_P2_RDB.h b/include/configs/P1_P2_RDB.h
index 6ce4cbef9c..699e9ebcda 100644
--- a/include/configs/P1_P2_RDB.h
+++ b/include/configs/P1_P2_RDB.h
@@ -369,7 +369,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /* I2C */
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C		/* I2C with hardware support */
-#undef	CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_I2C_CMD_TREE
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address*/
diff --git a/include/configs/P2020COME.h b/include/configs/P2020COME.h
index 05a75d8a76..c8f5a85ded 100644
--- a/include/configs/P2020COME.h
+++ b/include/configs/P2020COME.h
@@ -227,7 +227,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /* I2C */
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C		/* I2C with hardware support */
-#undef  CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_I2C_CMD_TREE
 #define CONFIG_SYS_I2C_SPEED		400000  /* I2C speed and slave address*/
diff --git a/include/configs/PM826.h b/include/configs/PM826.h
index faadfe43c1..5508313cec 100644
--- a/include/configs/PM826.h
+++ b/include/configs/PM826.h
@@ -57,10 +57,10 @@
 	"bootm"
 
 /* enable I2C and select the hardware/software driver */
-#undef  CONFIG_HARD_I2C
-#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
-# define CONFIG_SYS_I2C_SPEED		50000
-# define CONFIG_SYS_I2C_SLAVE		0xFE
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 /*
  * Software (bit-bang) I2C driver configuration
  */
diff --git a/include/configs/PM828.h b/include/configs/PM828.h
index f563fbe335..3842f57c0e 100644
--- a/include/configs/PM828.h
+++ b/include/configs/PM828.h
@@ -57,10 +57,10 @@
 	"bootm"
 
 /* enable I2C and select the hardware/software driver */
-#undef	CONFIG_HARD_I2C
-#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
-# define CONFIG_SYS_I2C_SPEED		50000
-# define CONFIG_SYS_I2C_SLAVE		0xFE
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 /*
  * Software (bit-bang) I2C driver configuration
  */
diff --git a/include/configs/PMC440.h b/include/configs/PMC440.h
index 40c18274f9..4b531828f5 100644
--- a/include/configs/PMC440.h
+++ b/include/configs/PMC440.h
@@ -226,7 +226,6 @@
  * I2C
  *----------------------------------------------------------------------*/
 #define CONFIG_HARD_I2C		1	/* I2C with hardware support    */
-#undef	CONFIG_SOFT_I2C		/* I2C bit-banged               */
 #define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address  */
 #define CONFIG_SYS_I2C_SLAVE		0x7F
diff --git a/include/configs/R360MPI.h b/include/configs/R360MPI.h
index 60cccffc45..df16598e3c 100644
--- a/include/configs/R360MPI.h
+++ b/include/configs/R360MPI.h
@@ -97,10 +97,13 @@
 #define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
 
 #define CONFIG_HARD_I2C		1	/* To I2C with hardware support */
-#undef CONFIG_SORT_I2C			/* To I2C with software support */
+#undef CONFIG_SYS_I2C_SOFT		/* To I2C with software support */
 #define CONFIG_SYS_I2C_SPEED		4700	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 
+#if defined(CONFIG_SYS_I2C_SOFT)
+#define CONFIG_SYS_SYS_I2C_SOFT_SPEED	4700 /* I2C speed and slave address */
+#define CONFIG_SYS_SYS_I2C_SOFT_SLAVE	0x7F
 /*
  * Software (bit-bang) I2C driver configuration
  */
@@ -116,6 +119,7 @@
 #define I2C_SCL(bit)		if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
 				else    immr->im_cpm.cp_pbdat &= ~PB_SCL
 #define I2C_DELAY		udelay(50)
+#endif /* #define(CONFIG_SYS_I2C_SOFT) */
 
 #define CONFIG_SYS_I2C_LCD_ADDR	0x8	/* LCD Control */
 #define CONFIG_SYS_I2C_KEY_ADDR	0x9	/* Keyboard coprocessor */
diff --git a/include/configs/RPXClassic.h b/include/configs/RPXClassic.h
index 3595200c45..8130ee6e0a 100644
--- a/include/configs/RPXClassic.h
+++ b/include/configs/RPXClassic.h
@@ -148,14 +148,16 @@
  * I2C Configuration
  *-----------------------------------------------------------------------------
  */
-#define CONFIG_I2C              1
-#define CONFIG_SYS_I2C_SPEED           50000
-#define CONFIG_SYS_I2C_SLAVE           0x34
+#define CONFIG_SYS_I2C_SPEED		50000
+#define CONFIG_SYS_I2C_SLAVE		0x34
 
 
 /* enable I2C and select the hardware/software driver */
 #define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#undef  CONFIG_SOFT_I2C			/* I2C bit-banged		*/
+#undef  CONFIG_SYS_I2C_SOFT		/* I2C bit-banged		*/
+
+#if defined(CONFIG_SYS_I2C_SOFT)
+#define CONFIG_SYS_I2C			1
 /*
  * Software (bit-bang) I2C driver configuration
  */
@@ -170,8 +172,10 @@
 #define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
 
 
-# define CONFIG_SYS_I2C_SPEED		50000
-# define CONFIG_SYS_I2C_SLAVE		0x34
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0x34
+#endif
+
 # define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM X24C16		*/
 # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* bytes of address		*/
 /* mask of address bits that overflow into the "EEPROM chip address"    */
diff --git a/include/configs/RPXlite.h b/include/configs/RPXlite.h
index 563abea95e..9a385a48b6 100644
--- a/include/configs/RPXlite.h
+++ b/include/configs/RPXlite.h
@@ -62,6 +62,36 @@
 #undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
 
 #define CONFIG_BZIP2		/* Include support for bzip2 compressed images  */
+
+/* enable I2C and select the hardware/software driver */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	40000	/* 40 kHz is supposed to work */
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
+/* Software (bit-bang) I2C driver configuration */
+#define PB_SCL		0x00000020	/* PB 26 */
+#define PB_SDA		0x00000010	/* PB 27 */
+
+#define I2C_INIT	(immr->im_cpm.cp_pbdir |=  PB_SCL)
+#define I2C_ACTIVE	(immr->im_cpm.cp_pbdir |=  PB_SDA)
+#define I2C_TRISTATE	(immr->im_cpm.cp_pbdir &= ~PB_SDA)
+#define I2C_READ	((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
+#define I2C_SDA(bit)	if (bit) \
+				immr->im_cpm.cp_pbdat |=  PB_SDA; \
+			else \
+				immr->im_cpm.cp_pbdat &= ~PB_SDA
+#define I2C_SCL(bit)	if (bit) \
+				immr->im_cpm.cp_pbdat |=  PB_SCL; \
+			else \
+				immr->im_cpm.cp_pbdat &= ~PB_SCL
+#define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
+
+/* M41T11 Serial Access Timekeeper(R) SRAM */
+#define CONFIG_RTC_M41T11 1
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+/* play along with the linux driver */
+#define CONFIG_SYS_M41T11_BASE_YEAR 1900
+
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
 /*
diff --git a/include/configs/RRvision.h b/include/configs/RRvision.h
index e2ea016387..b14136df13 100644
--- a/include/configs/RRvision.h
+++ b/include/configs/RRvision.h
@@ -122,13 +122,10 @@
 #endif
 
 /* enable I2C and select the hardware/software driver */
-#undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
-
-# define CONFIG_SYS_I2C_SPEED		50000	/* 50 kHz is supposed to work	*/
-# define CONFIG_SYS_I2C_SLAVE		0xFE
-
-#ifdef CONFIG_SOFT_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 /*
  * Software (bit-bang) I2C driver configuration
  */
@@ -144,7 +141,6 @@
 #define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
 			else    immr->im_cpm.cp_pbdat &= ~PB_SCL
 #define I2C_DELAY	udelay(1)	/* 1/4 I2C clock duration */
-#endif	/* CONFIG_SOFT_I2C */
 
 
 /*
diff --git a/include/configs/SXNI855T.h b/include/configs/SXNI855T.h
index b7fbe5e153..f0ce2828c2 100644
--- a/include/configs/SXNI855T.h
+++ b/include/configs/SXNI855T.h
@@ -121,7 +121,10 @@
 
 #define	CONFIG_RTC_DS1306		/* Dallas 1306 real time clock	*/
 
-#define	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 /*
  * Software (bit-bang) I2C driver configuration
  */
@@ -138,8 +141,6 @@
 			else    immr->im_cpm.cp_pbdat &= ~PB_SCL
 #define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
 
-# define CONFIG_SYS_I2C_SPEED		50000
-# define CONFIG_SYS_I2C_SLAVE		0xFE
 # define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* Atmel 24C64			*/
 # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2	/* two byte address		*/
 
diff --git a/include/configs/Sandpoint8240.h b/include/configs/Sandpoint8240.h
index fa456ed79f..65ca4259d8 100644
--- a/include/configs/Sandpoint8240.h
+++ b/include/configs/Sandpoint8240.h
@@ -202,13 +202,16 @@
  * If the software driver is chosen, there are some additional
  * configuration items that the driver uses to drive the port pins.
  */
-#define CONFIG_HARD_I2C		1		/* To enable I2C support	*/
-#undef  CONFIG_SOFT_I2C				/* I2C bit-banged		*/
-#define CONFIG_SYS_I2C_SPEED		400000		/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_HARD_I2C		1		/* To enable I2C support */
+#undef  CONFIG_SYS_I2C_SOFT
+#define CONFIG_SYS_I2C_SLAVE	0x7F
+#define CONFIG_SYS_I2C_SPEED	400000
 
-#ifdef CONFIG_SOFT_I2C
+#ifdef CONFIG_SYS_I2C_SOFT
 #error "Soft I2C is not configured properly.  Please review!"
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 #define I2C_PORT		3               /* Port A=0, B=1, C=2, D=3 */
 #define I2C_ACTIVE		(iop->pdir |=  0x00010000)
 #define I2C_TRISTATE		(iop->pdir &= ~0x00010000)
@@ -218,7 +221,7 @@
 #define I2C_SCL(bit)		if(bit) iop->pdat |=  0x00020000; \
 				else    iop->pdat &= ~0x00020000
 #define I2C_DELAY		udelay(5)	/* 1/4 I2C clock duration */
-#endif /* CONFIG_SOFT_I2C */
+#endif /* CONFIG_SYS_I2C_SOFT */
 
 
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x57		/* EEPROM IS24C02		*/
diff --git a/include/configs/Sandpoint8245.h b/include/configs/Sandpoint8245.h
index cdc51a5016..9a69374221 100644
--- a/include/configs/Sandpoint8245.h
+++ b/include/configs/Sandpoint8245.h
@@ -172,13 +172,16 @@
  * If the software driver is chosen, there are some additional
  * configuration items that the driver uses to drive the port pins.
  */
-#define CONFIG_HARD_I2C		1		/* To enable I2C support	*/
-#undef  CONFIG_SOFT_I2C				/* I2C bit-banged		*/
-#define CONFIG_SYS_I2C_SPEED		400000		/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_HARD_I2C		1		/* To enable I2C support */
+#undef  CONFIG_SYS_I2C_SOFT
+#define CONFIG_SYS_I2C_SPEED	400000
+#define CONFIG_SYS_I2C_SLAVE	0x7F
 
-#ifdef CONFIG_SOFT_I2C
+#ifdef CONFIG_SYS_I2C_SOFT
 #error "Soft I2C is not configured properly.  Please review!"
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 #define I2C_PORT		3               /* Port A=0, B=1, C=2, D=3 */
 #define I2C_ACTIVE		(iop->pdir |=  0x00010000)
 #define I2C_TRISTATE		(iop->pdir &= ~0x00010000)
@@ -188,7 +191,7 @@
 #define I2C_SCL(bit)		if(bit) iop->pdat |=  0x00020000; \
 				else    iop->pdat &= ~0x00020000
 #define I2C_DELAY		udelay(5)	/* 1/4 I2C clock duration */
-#endif /* CONFIG_SOFT_I2C */
+#endif /* CONFIG_SYS_I2C_SOFT */
 
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x57		/* EEPROM IS24C02		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1		/* Bytes of address		*/
diff --git a/include/configs/TASREG.h b/include/configs/TASREG.h
index d95a22611d..059fb362f8 100644
--- a/include/configs/TASREG.h
+++ b/include/configs/TASREG.h
@@ -136,19 +136,11 @@
 /*-----------------------------------------------------------------------
  * I2C
  */
-#define	CONFIG_SOFT_I2C
-#define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC32		*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2	/* Bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"	*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x01
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5	/* The Catalyst CAT24WC32 has	*/
-					/* 32 byte page write mode using*/
-					/* last 5 bits of the address	*/
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	100000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0x7F
 
-#if defined (CONFIG_SOFT_I2C)
 #if 0 /* push-pull */
 #define	SDA	        0x00800000
 #define	SCL	        0x00000008
@@ -182,7 +174,17 @@
 #define	I2C_ACTIVE	{DIR1|=SDA;}
 #define	I2C_TRISTATE    {DIR1&=~SDA;}
 #endif
-#endif
+
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC32	*/
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2	/* Bytes of address	*/
+/* mask of address bits that overflow into the "EEPROM chip address"	*/
+#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x01
+/*
+ * The Catalyst CAT24WC32 has 32 byte page write mode using
+ * last 5 bits of the address
+ */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
 
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
diff --git a/include/configs/TK885D.h b/include/configs/TK885D.h
index 623cb6636b..af8877373d 100644
--- a/include/configs/TK885D.h
+++ b/include/configs/TK885D.h
@@ -104,13 +104,10 @@
 #undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
 
 /* enable I2C and select the hardware/software driver */
-#undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
-
-#define CONFIG_SYS_I2C_SPEED		93000	/* 93 kHz is supposed to work	*/
-#define CONFIG_SYS_I2C_SLAVE		0xFE
-
-#ifdef CONFIG_SOFT_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT			/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	93000	/* 93 kHz is supposed to work */
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 /*
  * Software (bit-bang) I2C driver configuration
  */
@@ -126,7 +123,6 @@
 #define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
 			else	immr->im_cpm.cp_pbdat &= ~PB_SCL
 #define I2C_DELAY	udelay(2)	/* 1/4 I2C clock duration */
-#endif	/* CONFIG_SOFT_I2C */
 
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x50		/* EEPROM AT24C??	*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2		/* two byte address	*/
diff --git a/include/configs/TOP5200.h b/include/configs/TOP5200.h
index 2267d59d75..e9dcefc789 100644
--- a/include/configs/TOP5200.h
+++ b/include/configs/TOP5200.h
@@ -200,10 +200,13 @@
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_MISC_INIT_R
 
-#undef	CONFIG_HARD_I2C			/* I2C with hardware support */
-#define	CONFIG_SOFT_I2C		1	/* I2C with softwate support */
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
 
-#if defined (CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
+#  define CONFIG_SYS_I2C
+#  define CONFIG_SYS_I2C_SOFT_SPEED	100000
+#  define CONFIG_SYS_I2C_SOFT_SLAVE	0x7F
+/**/
 #  define SDA0			0x40
 #  define SCL0			0x80
 #  define GPIOE0		*((volatile uchar*)(CONFIG_SYS_MBAR+0x0c00))
@@ -218,8 +221,7 @@
 #  define I2C_DELAY		{udelay(5);}
 #  define I2C_ACTIVE	{DDR0|=SDA0;}
 #  define I2C_TRISTATE	{DDR0&=~SDA0;}
-#  define CONFIG_SYS_I2C_SPEED		100000
-#  define CONFIG_SYS_I2C_SLAVE		0x7F
+
 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
 #define CONFIG_SYS_I2C_FACT_ADDR	0x57
 #endif
diff --git a/include/configs/TOP860.h b/include/configs/TOP860.h
index 4849f94c99..1f728e3d4a 100644
--- a/include/configs/TOP860.h
+++ b/include/configs/TOP860.h
@@ -159,7 +159,6 @@
  * Environment handler
  * only the first 6k in EEPROM are available for user. Of that we use 256b
  */
-#define	CONFIG_SOFT_I2C
 #define CONFIG_ENV_IS_IN_EEPROM	1	/* turn on EEPROM env feature */
 #define CONFIG_ENV_OFFSET		0x1000
 #define CONFIG_ENV_SIZE		0x0700
@@ -170,13 +169,15 @@
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
 #define CONFIG_SYS_EEPROM_SIZE 0x2000
-#define	CONFIG_SYS_I2C_SPEED	100000
-#define	CONFIG_SYS_I2C_SLAVE	0xFE
 #define	CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 12
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_MISC_INIT_R
 
-#if defined (CONFIG_SOFT_I2C)
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	100000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
+/**/
 #define	SDA	0x00010
 #define	SCL	0x00020
 #define __I2C_DIR	immr->im_cpm.cp_pbdir
@@ -193,7 +194,6 @@
 #define	I2C_DELAY	{ udelay(5); }
 #define	I2C_ACTIVE	{ __I2C_DIR |= SDA; }
 #define	I2C_TRISTATE	{ __I2C_DIR &= ~SDA; }
-#endif
 
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
 
diff --git a/include/configs/TQM8260.h b/include/configs/TQM8260.h
index 7e24131796..5fbfd1c970 100644
--- a/include/configs/TQM8260.h
+++ b/include/configs/TQM8260.h
@@ -89,10 +89,10 @@
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
 /* enable I2C and select the hardware/software driver */
-#undef  CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	400000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0x7F
 
 /*
  * Software (bit-bang) I2C driver configuration
diff --git a/include/configs/TQM8272.h b/include/configs/TQM8272.h
index 3b3f9e6302..c27e4ef1d0 100644
--- a/include/configs/TQM8272.h
+++ b/include/configs/TQM8272.h
@@ -97,11 +97,10 @@
 
 #if CONFIG_I2C
 /* enable I2C and select the hardware/software driver */
-#undef  CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	400000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0x7F
 /*
  * Software (bit-bang) I2C driver configuration
  */
@@ -135,8 +134,9 @@
 #define CONFIG_SYS_DTT_HYSTERESIS	3
 
 #else
+#undef CONFIG_SYS_I2C
 #undef CONFIG_HARD_I2C
-#undef CONFIG_SOFT_I2C
+#undef CONFIG_SYS_I2C_SOFT
 #endif
 
 /*
diff --git a/include/configs/TQM834x.h b/include/configs/TQM834x.h
index 966a6e3da9..f22eb35c2f 100644
--- a/include/configs/TQM834x.h
+++ b/include/configs/TQM834x.h
@@ -188,7 +188,6 @@
  * I2C
  */
 #define CONFIG_HARD_I2C			/* I2C with hardware support */
-#undef CONFIG_SOFT_I2C			/* I2C bit-banged */
 #define CONFIG_FSL_I2C
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed: 400KHz */
 #define CONFIG_SYS_I2C_SLAVE		0x7F	/* slave address */
diff --git a/include/configs/TQM855M.h b/include/configs/TQM855M.h
index e7fd2db28e..1b558fc4d3 100644
--- a/include/configs/TQM855M.h
+++ b/include/configs/TQM855M.h
@@ -93,13 +93,10 @@
 #undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
 
 /* enable I2C and select the hardware/software driver */
-#undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define	CONFIG_SOFT_I2C         1	/* I2C bit-banged		*/
-
-#define CONFIG_SYS_I2C_SPEED		93000	/* 93 kHz is supposed to work	*/
-#define CONFIG_SYS_I2C_SLAVE		0xFE
-
-#ifdef CONFIG_SOFT_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	93000	/* 93 kHz is supposed to work */
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 /*
  * Software (bit-bang) I2C driver configuration
  */
@@ -115,7 +112,6 @@
 #define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
 			else    immr->im_cpm.cp_pbdat &= ~PB_SCL
 #define I2C_DELAY	udelay(2)	/* 1/4 I2C clock duration */
-#endif	/* CONFIG_SOFT_I2C */
 
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x50		/* EEPROM AT24C64	*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2		/* two byte address	*/
diff --git a/include/configs/TQM866M.h b/include/configs/TQM866M.h
index 7d0ae99cb1..910497126f 100644
--- a/include/configs/TQM866M.h
+++ b/include/configs/TQM866M.h
@@ -107,13 +107,11 @@
 #undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
 
 /* enable I2C and select the hardware/software driver */
-#undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT			/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	93000	/* 93 kHz is supposed to work */
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 
-#define CONFIG_SYS_I2C_SPEED		93000	/* 93 kHz is supposed to work	*/
-#define CONFIG_SYS_I2C_SLAVE		0xFE
-
-#ifdef CONFIG_SOFT_I2C
 /*
  * Software (bit-bang) I2C driver configuration
  */
@@ -129,7 +127,6 @@
 #define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
 			else	immr->im_cpm.cp_pbdat &= ~PB_SCL
 #define I2C_DELAY	udelay(2)	/* 1/4 I2C clock duration */
-#endif	/* CONFIG_SOFT_I2C */
 
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x50		/* EEPROM AT24C256	*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2		/* two byte address	*/
diff --git a/include/configs/TQM885D.h b/include/configs/TQM885D.h
index 7941631b51..65d7c58189 100644
--- a/include/configs/TQM885D.h
+++ b/include/configs/TQM885D.h
@@ -101,13 +101,10 @@
 #undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
 
 /* enable I2C and select the hardware/software driver */
-#undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
-
-#define CONFIG_SYS_I2C_SPEED		93000	/* 93 kHz is supposed to work	*/
-#define CONFIG_SYS_I2C_SLAVE		0xFE
-
-#ifdef CONFIG_SOFT_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT			/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	93000	/* 93 kHz is supposed to work */
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 /*
  * Software (bit-bang) I2C driver configuration
  */
@@ -123,7 +120,6 @@
 #define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
 			else	immr->im_cpm.cp_pbdat &= ~PB_SCL
 #define I2C_DELAY	udelay(2)	/* 1/4 I2C clock duration */
-#endif	/* CONFIG_SOFT_I2C */
 
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x50		/* EEPROM AT24C??	*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2		/* two byte address	*/
diff --git a/include/configs/alpr.h b/include/configs/alpr.h
index d93d5e204f..9f32a608c0 100644
--- a/include/configs/alpr.h
+++ b/include/configs/alpr.h
@@ -122,7 +122,6 @@
  * I2C
  *----------------------------------------------------------------------*/
 #define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
 #define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
 #define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed and slave address	*/
 #define CONFIG_SYS_I2C_SLAVE		0x7F
diff --git a/include/configs/aria.h b/include/configs/aria.h
index bd81053875..261dc695c6 100644
--- a/include/configs/aria.h
+++ b/include/configs/aria.h
@@ -371,7 +371,6 @@
 
 /* I2C */
 #define CONFIG_HARD_I2C			/* I2C with hardware support */
-#undef CONFIG_SOFT_I2C			/* so disable bit-banged I2C */
 #define CONFIG_I2C_MULTI_BUS
 
 /* I2C speed and slave address */
diff --git a/include/configs/astro_mcf5373l.h b/include/configs/astro_mcf5373l.h
index a0ed8f18f5..6dabe57e7c 100644
--- a/include/configs/astro_mcf5373l.h
+++ b/include/configs/astro_mcf5373l.h
@@ -118,7 +118,6 @@
 /* I2C */
 #define CONFIG_FSL_I2C
 #define CONFIG_HARD_I2C			/* I2C with hw support */
-#undef CONFIG_SOFT_I2C			/* I2C bit-banged */
 #define CONFIG_SYS_I2C_SPEED		80000
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #define CONFIG_SYS_I2C_OFFSET		0x58000
diff --git a/include/configs/bf533-ezkit.h b/include/configs/bf533-ezkit.h
index c1a5ecda7e..beab1271a4 100644
--- a/include/configs/bf533-ezkit.h
+++ b/include/configs/bf533-ezkit.h
@@ -94,10 +94,15 @@
 /*
  * I2C Settings
  */
-#define CONFIG_SOFT_I2C
+#define CONFIG_SYS_I2C_SOFT
+#ifdef CONFIG_SYS_I2C_SOFT
+#define CONFIG_SYS_I2C
 #define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF0
 #define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF1
-
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0
+#define I2C_DELAY              udelay(5)       /* 1/4 I2C clock duration */
+#endif
 
 /*
  * Misc Settings
diff --git a/include/configs/bf533-stamp.h b/include/configs/bf533-stamp.h
index e3344e9e85..7144c6319f 100644
--- a/include/configs/bf533-stamp.h
+++ b/include/configs/bf533-stamp.h
@@ -14,7 +14,6 @@
 #define CONFIG_BFIN_CPU             bf533-0.3
 #define CONFIG_BFIN_BOOT_MODE       BFIN_BOOT_BYPASS
 
-
 /*
  * Clock Settings
  *	CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
@@ -38,7 +37,6 @@
 /* Values can range from 1-15						*/
 #define CONFIG_SCLK_DIV			6 /* note: 1.2 boards can go faster */
 
-
 /*
  * Memory Settings
  */
@@ -74,6 +72,42 @@
 /* #define CONFIG_ETHADDR	02:80:ad:20:31:b8 */
 
 
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define PF_SCL			PF3
+#define PF_SDA			PF2
+#define I2C_INIT		(*pFIO_DIR |=  PF_SCL); asm("ssync;")
+#define I2C_ACTIVE		(*pFIO_DIR |=  PF_SDA); \
+				*pFIO_INEN &= ~PF_SDA; asm("ssync;")
+#define I2C_TRISTATE		(*pFIO_DIR &= ~PF_SDA); \
+				*pFIO_INEN |= PF_SDA; asm("ssync;")
+#define I2C_READ		((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); \
+				asm("ssync;")
+#define I2C_SDA(bit)	if (bit) { \
+				*pFIO_FLAG_S = PF_SDA; \
+				asm("ssync;"); \
+				} \
+			else	{ \
+				*pFIO_FLAG_C = PF_SDA; \
+				asm("ssync;"); \
+				}
+#define I2C_SCL(bit)	if (bit) { \
+				*pFIO_FLAG_S = PF_SCL; \
+				asm("ssync;"); \
+				} \
+			else	{ \
+				*pFIO_FLAG_C = PF_SCL; \
+				asm("ssync;"); \
+				}
+#define I2C_DELAY		udelay(5)	/* 1/4 I2C clock duration */
+
+
 /*
  * Flash Settings
  */
@@ -84,7 +118,6 @@
 #define CONFIG_SYS_MAX_FLASH_BANKS	1
 #define CONFIG_SYS_MAX_FLASH_SECT	67
 
-
 /*
  * SPI Settings
  */
@@ -132,10 +165,15 @@
 /*
  * I2C Settings
  */
-#define CONFIG_SOFT_I2C
+#define CONFIG_SYS_I2C_SOFT
+#ifdef CONFIG_SYS_I2C_SOFT
+#define CONFIG_SYS_I2C
 #define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF3
 #define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF2
-
+#define I2C_DELAY		udelay(5)	/* 1/4 I2C clock duration */
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0
+#endif
 
 /*
  * Compact Flash / IDE / ATA Settings
diff --git a/include/configs/bf561-ezkit.h b/include/configs/bf561-ezkit.h
index 6ee1e4c869..404039ac23 100644
--- a/include/configs/bf561-ezkit.h
+++ b/include/configs/bf561-ezkit.h
@@ -88,10 +88,14 @@
 /*
  * I2C Settings
  */
-#define CONFIG_SOFT_I2C
+#define CONFIG_SYS_I2C_SOFT
+#ifdef CONFIG_SYS_I2C_SOFT
 #define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF0
 #define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF1
-
+#define I2C_DELAY		udelay(5)	/* 1/4 I2C clock duration */
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0
+#endif
 
 /*
  * Misc Settings
diff --git a/include/configs/bfin_adi_common.h b/include/configs/bfin_adi_common.h
index e1a6fe3056..08ccce0b9a 100644
--- a/include/configs/bfin_adi_common.h
+++ b/include/configs/bfin_adi_common.h
@@ -71,7 +71,7 @@
 # ifdef CONFIG_SPI_FLASH
 #  define CONFIG_CMD_SF
 # endif
-# if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C)
+# if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT)
 #  define CONFIG_CMD_I2C
 #  define CONFIG_SOFT_I2C_READ_REPEATED_START
 # endif
@@ -299,7 +299,7 @@
 /*
  * I2C Settings
  */
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT)
 # ifndef CONFIG_SYS_I2C_SPEED
 #  define CONFIG_SYS_I2C_SPEED 50000
 # endif
diff --git a/include/configs/blackstamp.h b/include/configs/blackstamp.h
index 83ad659cdf..7d8227503a 100644
--- a/include/configs/blackstamp.h
+++ b/include/configs/blackstamp.h
@@ -40,7 +40,6 @@
 #define SHARED_RESOURCES	1
 
 /* Is I2C bit-banged? */
-#undef CONFIG_SOFT_I2
 
 /*
  * Clock Settings
@@ -115,7 +114,7 @@
 # undef CONFIG_CMD_NET
 #endif
 
-#ifdef CONFIG_SOFT_I2C
+#ifdef CONFIG_SYS_I2C_SOFT
 # define CONFIG_CMD_I2C
 #endif
 
@@ -204,11 +203,11 @@
  * Note these pins are arbitrarily chosen because we aren't using
  * them yet. You can (and probably should) change these values!
  */
-#ifdef CONFIG_SOFT_I2C
+#ifdef CONFIG_SYS_I2C_SOFT
 #define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF9
 #define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF8
-#define CONFIG_SYS_I2C_SPEED		50000
-#define CONFIG_SYS_I2C_SLAVE		0xFE
+#define CONFIG_SYS_SOFT_I2C_SPEED	50000
+#define CONFIG_SYS_SOFT_I2C_SLAVE	0xFE
 #endif
 
 /*
diff --git a/include/configs/blackvme.h b/include/configs/blackvme.h
index 523c4e409a..cd37f9adb9 100644
--- a/include/configs/blackvme.h
+++ b/include/configs/blackvme.h
@@ -224,7 +224,7 @@
  * Soft I2C settings (BF561 does not have hard I2C)
  * PF12,13 on SPI connector 0.
  */
-#ifdef CONFIG_SOFT_I2C
+#ifdef CONFIG_SYS_I2C_SOFT
 # define CONFIG_CMD_I2C
 # define CONFIG_SOFT_I2C_GPIO_SCL	GPIO_PF12
 # define CONFIG_SOFT_I2C_GPIO_SDA	GPIO_PF13
diff --git a/include/configs/cpuat91.h b/include/configs/cpuat91.h
index 15d56c346d..d9b006ab7b 100644
--- a/include/configs/cpuat91.h
+++ b/include/configs/cpuat91.h
@@ -92,7 +92,6 @@
 #define CONFIG_USART_ID		0/* ignored in arm */
 
 #undef CONFIG_HARD_I2C
-#undef CONFIG_SOFT_I2C
 #define AT91_PIN_SDA			(1<<25)
 #define AT91_PIN_SCL			(1<<26)
 
@@ -139,7 +138,7 @@
 #undef CONFIG_CMD_NFS
 #undef CONFIG_CMD_DHCP
 
-#ifdef CONFIG_SOFT_I2C
+#ifdef CONFIG_SYS_I2C_SOFT
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_I2C
 #endif
diff --git a/include/configs/debris.h b/include/configs/debris.h
index c40fbd9f8d..0d3a4fa290 100644
--- a/include/configs/debris.h
+++ b/include/configs/debris.h
@@ -273,12 +273,15 @@
  * configuration items that the driver uses to drive the port pins.
  */
 #define CONFIG_HARD_I2C		1		/* To enable I2C support	*/
-#undef  CONFIG_SOFT_I2C				/* I2C bit-banged		*/
+#undef  CONFIG_SYS_I2C_SOFT			/* I2C bit-banged */
 #define CONFIG_SYS_I2C_SPEED		400000		/* I2C speed and slave address	*/
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 
-#ifdef CONFIG_SOFT_I2C
+#ifdef CONFIG_SYS_I2C_SOFT
 #error "Soft I2C is not configured properly.  Please review!"
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0x7F
 #define I2C_PORT		3               /* Port A=0, B=1, C=2, D=3 */
 #define I2C_ACTIVE		(iop->pdir |=  0x00010000)
 #define I2C_TRISTATE		(iop->pdir &= ~0x00010000)
@@ -288,7 +291,7 @@
 #define I2C_SCL(bit)		if(bit) iop->pdat |=  0x00020000; \
 				else    iop->pdat &= ~0x00020000
 #define I2C_DELAY		udelay(5)	/* 1/4 I2C clock duration */
-#endif /* CONFIG_SOFT_I2C */
+#endif /* CONFIG_SYS_I2C_SOFT */
 
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x57		/* EEPROM IS24C02		*/
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1		/* Bytes of address		*/
diff --git a/include/configs/eXalion.h b/include/configs/eXalion.h
index a6a0f8bb58..b80ab3fcf0 100644
--- a/include/configs/eXalion.h
+++ b/include/configs/eXalion.h
@@ -224,7 +224,7 @@
  * configuration items that the driver uses to drive the port pins.
  */
 #define CONFIG_HARD_I2C		1	/* To enable I2C support	*/
-#undef	CONFIG_SOFT_I2C		/* I2C bit-banged		*/
+#undef	CONFIG_SYS_I2C_SOFT		/* I2C bit-banged		*/
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 
diff --git a/include/configs/eb_cpux9k2.h b/include/configs/eb_cpux9k2.h
index 3be4929fc2..efb50e3778 100644
--- a/include/configs/eb_cpux9k2.h
+++ b/include/configs/eb_cpux9k2.h
@@ -223,11 +223,10 @@
  * I2C-Bus
  */
 
-#define CONFIG_SYS_I2C_SPEED		50000
-#define CONFIG_SYS_I2C_SLAVE		0 		/* not used */
-
-#ifndef CONFIG_HARD_I2C
-#define CONFIG_SOFT_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0
 
 /* Software  I2C driver configuration */
 
@@ -251,9 +250,7 @@
 	else							\
 		writel(ATMEL_PMX_AA_TWCK, &pio->pioa.codr);
 
-#define I2C_DELAY	udelay(2500000/CONFIG_SYS_I2C_SPEED)
-
-#endif	/* CONFIG_HARD_I2C */
+#define I2C_DELAY	udelay(2500000/CONFIG_SYS_I2C_SOFT_SPEED)
 
 /* I2C-RTC */
 
diff --git a/include/configs/ep8260.h b/include/configs/ep8260.h
index 5a87cc5d3d..2e675bce61 100644
--- a/include/configs/ep8260.h
+++ b/include/configs/ep8260.h
@@ -227,15 +227,18 @@
  * If the software driver is chosen, there are some additional
  * configuration items that the driver uses to drive the port pins.
  */
-#undef  CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_SLAVE		0x7F	/* This is for HARD, must go */
 
 /*
  * Software (bit-bang) I2C driver configuration
  */
-#ifdef CONFIG_SOFT_I2C
+#ifdef CONFIG_SYS_I2C_SOFT
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 #define I2C_PORT	3		/* Port A=0, B=1, C=2, D=3 */
 #define I2C_ACTIVE	(iop->pdir |=  0x00010000)
 #define I2C_TRISTATE	(iop->pdir &= ~0x00010000)
@@ -245,7 +248,7 @@
 #define I2C_SCL(bit)	if(bit) iop->pdat |=  0x00020000; \
 			else    iop->pdat &= ~0x00020000
 #define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
-#endif /* CONFIG_SOFT_I2C */
+#endif /* CONFIG_SYS_I2C_SOFT */
 
 /* #define CONFIG_RTC_DS174x */
 
diff --git a/include/configs/ethernut5.h b/include/configs/ethernut5.h
index 14a0f02c5e..5bf8c22498 100644
--- a/include/configs/ethernut5.h
+++ b/include/configs/ethernut5.h
@@ -210,10 +210,12 @@
 
 /* I2C */
 #define CONFIG_SYS_MAX_I2C_BUS	1
-#define CONFIG_SYS_I2C_SLAVE	0
-#define CONFIG_SYS_I2C_SPEED	100000
 
-#define CONFIG_SOFT_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT			/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	100000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0
+
 #define I2C_SOFT_DECLARATIONS
 
 #define GPIO_I2C_SCL		AT91_PIO_PORTA, 24
diff --git a/include/configs/ibf-dsp561.h b/include/configs/ibf-dsp561.h
index 294af735d6..5291755121 100644
--- a/include/configs/ibf-dsp561.h
+++ b/include/configs/ibf-dsp561.h
@@ -105,11 +105,11 @@
 /*
  * I2C Settings
  */
-#define CONFIG_SOFT_I2C		1
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
 #define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF0
 #define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF1
 
-
 /*
  * Misc Settings
  */
diff --git a/include/configs/iocon.h b/include/configs/iocon.h
index 7f8825bed1..695aa5c85a 100644
--- a/include/configs/iocon.h
+++ b/include/configs/iocon.h
@@ -110,11 +110,11 @@
 /*
  * I2C stuff
  */
-#define CONFIG_SYS_I2C_SPEED		400000
-
-/* enable I2C and select the hardware/software driver */
-#undef  CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
+#undef CONFIG_HARD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	400000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 
 /*
  * Software (bit-bang) I2C driver configuration
diff --git a/include/configs/km/keymile-common.h b/include/configs/km/keymile-common.h
index 3b15c4e691..6182e81a68 100644
--- a/include/configs/km/keymile-common.h
+++ b/include/configs/km/keymile-common.h
@@ -78,10 +78,7 @@
 #define CONFIG_LOADS_ECHO
 #define CONFIG_SYS_LOADS_BAUD_CHANGE
 
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_MAX_I2C_BUS		1
 #define CONFIG_SYS_I2C_INIT_BOARD
-#define CONFIG_I2C_MUX
 
 /* Support the IVM EEprom */
 #define	CONFIG_SYS_IVM_EEPROM_ADR	0x50
diff --git a/include/configs/km/km83xx-common.h b/include/configs/km/km83xx-common.h
index eb0e5b6f32..5a430edbc3 100644
--- a/include/configs/km/km83xx-common.h
+++ b/include/configs/km/km83xx-common.h
@@ -209,6 +209,9 @@
 #define CONFIG_SYS_I2C_SPEED	200000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_SLAVE	0x7F
 #define CONFIG_SYS_I2C_OFFSET	0x3000
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_MAX_I2C_BUS		1
+#define CONFIG_I2C_MUX
 
 /* I2C SYSMON (LM75, AD7414 is almost compatible) */
 #define CONFIG_DTT_LM75		/* ON Semi's LM75 */
diff --git a/include/configs/km/km_arm.h b/include/configs/km/km_arm.h
index 766d76e188..c2c67c1582 100644
--- a/include/configs/km/km_arm.h
+++ b/include/configs/km/km_arm.h
@@ -58,7 +58,6 @@
 
 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_SF
-#define CONFIG_SOFT_I2C		/* I2C bit-banged	*/
 
 /* SPI NOR Flash default params, used by sf commands */
 #define CONFIG_SF_DEFAULT_SPEED		8100000
@@ -187,8 +186,23 @@
 /*
  * I2C related stuff
  */
+#undef CONFIG_I2C_MVTWSI
+#define CONFIG_SYS_I2C
+#define	CONFIG_SYS_I2C_SOFT	/* I2C bit-banged	*/
+
 #define	CONFIG_KIRKWOOD_GPIO		/* Enable GPIO Support */
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
+
+#define CONFIG_SYS_NUM_I2C_BUSES	6
+#define CONFIG_SYS_I2C_MAX_HOPS		1
+#define CONFIG_SYS_I2C_BUSES	{	{0, {I2C_NULL_HOP} }, \
+					{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
+					{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
+					{0, {{I2C_MUX_PCA9547, 0x70, 3} } }, \
+					{0, {{I2C_MUX_PCA9547, 0x70, 4} } }, \
+					{0, {{I2C_MUX_PCA9547, 0x70, 5} } }, \
+				}
+
 #ifndef __ASSEMBLY__
 #include <asm/arch-kirkwood/gpio.h>
 extern void __set_direction(unsigned pin, int high);
@@ -211,6 +225,8 @@ int get_scl(void);
 #define I2C_DELAY	udelay(1)
 #define I2C_SOFT_DECLARATIONS
 
+#define	CONFIG_SYS_I2C_SOFT_SLAVE	0x0
+#define	CONFIG_SYS_I2C_SOFT_SPEED	100000
 #endif
 
 /* EEprom support 24C128, 24C256 valid for environment eeprom */
@@ -240,7 +256,7 @@ int get_scl(void);
 #define CONFIG_SYS_EEPROM_WREN
 #define CONFIG_ENV_OFFSET		0x0 /* no bracets! */
 #define CONFIG_ENV_SIZE			(0x2000 - CONFIG_ENV_OFFSET)
-#define CONFIG_I2C_ENV_EEPROM_BUS	KM_ENV_BUS "\0"
+#define CONFIG_I2C_ENV_EEPROM_BUS	KM_ENV_BUS
 #define CONFIG_ENV_OFFSET_REDUND	0x2000 /* no bracets! */
 #define CONFIG_ENV_SIZE_REDUND		(CONFIG_ENV_SIZE)
 #endif
@@ -293,7 +309,7 @@ int get_scl(void);
 	CONFIG_KM_DEF_ENV						\
 	CONFIG_KM_NEW_ENV						\
 	"arch=arm\0"							\
-	"EEprom_ivm=" KM_IVM_BUS "\0"					\
+	"EEprom_ivm=" __stringify(KM_IVM_BUS) "\0"			\
 	""
 
 #if defined(CONFIG_SYS_NO_FLASH)
diff --git a/include/configs/km82xx.h b/include/configs/km82xx.h
index 3c2117fc39..54041f3574 100644
--- a/include/configs/km82xx.h
+++ b/include/configs/km82xx.h
@@ -212,7 +212,7 @@
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
 	CONFIG_KM_BOARD_EXTRA_ENV					\
 	CONFIG_KM_DEF_ENV						\
-	"EEprom_ivm=pca9544a:70:4 \0"					\
+	"EEprom_ivm=1\0"						\
 	"unlock=yes\0"							\
 	"newenv="							\
 		"prot off 0xFE0C0000 +0x40000 && "			\
@@ -242,10 +242,16 @@
 #endif /* CONFIG_ENV_IS_IN_FLASH */
 
 /* enable I2C and select the hardware/software driver */
-#undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
-#define CONFIG_SYS_I2C_SPEED		50000	/* I2C speed */
-#define CONFIG_SYS_I2C_SLAVE		0x7F	/* I2C slave address */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_NUM_I2C_BUSES	3
+#define CONFIG_SYS_I2C_MAX_HOPS		1
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SPEED		CONFIG_SYS_I2C_SOFT_SPEED
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0x7F
+#define CONFIG_SYS_I2C_BUSES	{{0, {I2C_NULL_HOP} }, \
+			{0, {{I2C_MUX_PCA9542, 0x70, 0} } }, \
+			{0, {{I2C_MUX_PCA9542, 0x70, 1} } } }
 
 /*
  * Software (bit-bang) I2C driver configuration
@@ -282,7 +288,7 @@ int get_scl(void);
 #define CONFIG_SYS_DTT_MAX_TEMP	70
 #define CONFIG_SYS_DTT_LOW_TEMP	-30
 #define CONFIG_SYS_DTT_HYSTERESIS	3
-#define CONFIG_SYS_DTT_BUS_NUM		(CONFIG_SYS_MAX_I2C_BUS)
+#define CONFIG_SYS_DTT_BUS_NUM		2
 
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
 
diff --git a/include/configs/km_kirkwood.h b/include/configs/km_kirkwood.h
index 83bb7aad3d..a0ad47e73a 100644
--- a/include/configs/km_kirkwood.h
+++ b/include/configs/km_kirkwood.h
@@ -42,18 +42,18 @@
 #define CONFIG_IDENT_STRING		"\nKeymile Kirkwood"
 #define CONFIG_HOSTNAME			km_kirkwood
 #define CONFIG_KM_DISABLE_PCIE
-#define KM_IVM_BUS			"pca9544a:70:9"	/* I2C2 (Mux-Port 1)*/
+#define KM_IVM_BUS			1	/* I2C2 (Mux-Port 1)*/
 
 /* KM_KIRKWOOD_PCI */
 #elif defined(CONFIG_KM_KIRKWOOD_PCI)
 #define CONFIG_IDENT_STRING		"\nKeymile Kirkwood PCI"
 #define CONFIG_HOSTNAME			km_kirkwood_pci
-#define KM_IVM_BUS			"pca9544a:70:9"	/* I2C2 (Mux-Port 1)*/
+#define KM_IVM_BUS			1	/* I2C2 (Mux-Port 1)*/
 #define CONFIG_KM_FPGA_CONFIG
 
 /* KM_NUSA */
 #elif defined(CONFIG_KM_NUSA)
-#define KM_IVM_BUS			"pca9547:70:9"	/* I2C2 (Mux-Port 1)*/
+#define KM_IVM_BUS			1	/* I2C2 (Mux-Port 1)*/
 #define CONFIG_IDENT_STRING		"\nKeymile NUSA"
 #define CONFIG_HOSTNAME			kmnusa
 #undef CONFIG_SYS_KWD_CONFIG
@@ -69,7 +69,7 @@
 #elif defined(CONFIG_KM_MGCOGE3UN)
 #define CONFIG_IDENT_STRING		"\nKeymile COGE3UN"
 #define CONFIG_HOSTNAME			mgcoge3un
-#define KM_IVM_BUS			"pca9547:70:9" /* I2C2 (Mux-Port 1)*/
+#define KM_IVM_BUS			1	/* I2C2 (Mux-Port 1)*/
 #undef CONFIG_SYS_KWD_CONFIG
 #define CONFIG_SYS_KWD_CONFIG \
 		$(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage-memphis.cfg
@@ -81,7 +81,7 @@
 /* KMCOGE5UN */
 #elif defined(CONFIG_KM_COGE5UN)
 #define CONFIG_IDENT_STRING		"\nKeymile COGE5UN"
-#define KM_IVM_BUS			"pca9547:70:9"	/* I2C2 (Mux-Port 1)*/
+#define KM_IVM_BUS			1	/* I2C2 (Mux-Port 1)*/
 #undef	CONFIG_SYS_KWD_CONFIG
 #define CONFIG_SYS_KWD_CONFIG \
 		$(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage_256M8_1.cfg
@@ -95,12 +95,12 @@
 #elif defined(CONFIG_KM_PORTL2)
 #define CONFIG_IDENT_STRING		"\nKeymile Port-L2"
 #define CONFIG_HOSTNAME			portl2
-#define KM_IVM_BUS			"pca9544a:70:9" /* I2C2 (Mux-Port 1)*/
+#define KM_IVM_BUS			1	/* I2C2 (Mux-Port 1)*/
 #define CONFIG_KM_PIGGY4_88E6061
 
 /* KM_SUV31 */
 #elif defined(CONFIG_KM_SUV31)
-#define KM_IVM_BUS			"pca9547:70:9"	/* I2C2 (Mux-Port 1)*/
+#define CONFIG_KM_IVM_BUS		1	/* I2C2 (Mux-Port 1)*/
 #define CONFIG_IDENT_STRING		"\nKeymile SUV31"
 #define CONFIG_HOSTNAME			kmsuv31
 #define CONFIG_KM_ENV_IS_IN_SPI_NOR
@@ -114,7 +114,7 @@
 #include "km/km_arm.h"
 
 #ifndef CONFIG_KM_ENV_IS_IN_SPI_NOR
-#define KM_ENV_BUS	"pca9544a:70:d"	/* I2C2 (Mux-Port 5)*/
+#define KM_ENV_BUS	5	/* I2C2 (Mux-Port 5)*/
 #endif
 
 #if defined(CONFIG_KM_PIGGY4_88E6352)
diff --git a/include/configs/korat.h b/include/configs/korat.h
index d7c1f8508b..eea8c98b6a 100644
--- a/include/configs/korat.h
+++ b/include/configs/korat.h
@@ -156,7 +156,6 @@
  * I2C
  */
 #define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
 #define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
 #define CONFIG_SYS_I2C_SLAVE		0x7F
diff --git a/include/configs/lwmon.h b/include/configs/lwmon.h
index 3c02b73d8b..dc0bd33e8d 100644
--- a/include/configs/lwmon.h
+++ b/include/configs/lwmon.h
@@ -146,13 +146,10 @@
 #undef	CONFIG_STATUS_LED		/* Status LED disabled		*/
 
 /* enable I2C and select the hardware/software driver */
-#undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define	CONFIG_SOFT_I2C         1	/* I2C bit-banged		*/
-
-#define CONFIG_SYS_I2C_SPEED		93000	/* 93 kHz is supposed to work	*/
-#define CONFIG_SYS_I2C_SLAVE		0xFE
-
-#ifdef CONFIG_SOFT_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	93000	/* 93 kHz is supposed to work */
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 /*
  * Software (bit-bang) I2C driver configuration
  */
@@ -168,7 +165,6 @@
 #define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
 			else    immr->im_cpm.cp_pbdat &= ~PB_SCL
 #define I2C_DELAY	udelay(2)	/* 1/4 I2C clock duration */
-#endif	/* CONFIG_SOFT_I2C */
 
 
 #define CONFIG_RTC_PCF8563		/* use Philips PCF8563 RTC	*/
diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h
index ba613e33ce..4dcb25a966 100644
--- a/include/configs/lwmon5.h
+++ b/include/configs/lwmon5.h
@@ -299,7 +299,6 @@
  * I2C
  */
 #define CONFIG_HARD_I2C				/* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C				/* I2C bit-banged		*/
 #define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
 #define CONFIG_SYS_I2C_SPEED		100000		/* I2C speed and slave address	*/
 #define CONFIG_SYS_I2C_SLAVE		0x7F
diff --git a/include/configs/mecp5123.h b/include/configs/mecp5123.h
index c4f245b985..6f73e5d949 100644
--- a/include/configs/mecp5123.h
+++ b/include/configs/mecp5123.h
@@ -267,7 +267,6 @@
 
 /* I2C */
 #define CONFIG_HARD_I2C			/* I2C with hardware support */
-#undef CONFIG_SOFT_I2C			/* so disable bit-banged I2C */
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed */
 #define CONFIG_SYS_I2C_SLAVE		0x7F	/* slave address */
diff --git a/include/configs/mpc5121ads.h b/include/configs/mpc5121ads.h
index 6f003aa03f..65ca62fa31 100644
--- a/include/configs/mpc5121ads.h
+++ b/include/configs/mpc5121ads.h
@@ -360,7 +360,6 @@
 
 /* I2C */
 #define CONFIG_HARD_I2C			/* I2C with hardware support */
-#undef CONFIG_SOFT_I2C			/* so disable bit-banged I2C */
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_SLAVE		0x7F
diff --git a/include/configs/nhk8815.h b/include/configs/nhk8815.h
index d438efdae6..09073e9489 100644
--- a/include/configs/nhk8815.h
+++ b/include/configs/nhk8815.h
@@ -109,8 +109,11 @@
 #ifndef __ASSEMBLY__
 #include <asm/arch/gpio.h>
 #define CONFIG_CMD_I2C
-#define CONFIG_SOFT_I2C
-#define CONFIG_SYS_I2C_SPEED	400000
+#define CONFIG_SYS_I2C
+#define	CONFIG_SYS_I2C_SOFT	1	/* I2C bit-banged	*/
+#define I2C_SOFT_DEFS
+#define CONFIG_SYS_I2C_SOFT_SPEED	400000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0x7F
 #define __SDA			63
 #define __SCL			62
 #define I2C_SDA(x)		nmk_gpio_set(__SDA, x)
diff --git a/include/configs/otc570.h b/include/configs/otc570.h
index fe4f3c0fa3..010e1b9405 100644
--- a/include/configs/otc570.h
+++ b/include/configs/otc570.h
@@ -115,14 +115,13 @@
 /* RTC and I2C stuff */
 #define CONFIG_RTC_DS1338
 #define CONFIG_SYS_I2C_RTC_ADDR		0x68
-#undef CONFIG_HARD_I2C
-#define CONFIG_SOFT_I2C
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		0x7F
 
-#ifdef CONFIG_SOFT_I2C
-# define CONFIG_I2C_CMD_TREE
-# define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C
+#define	CONFIG_SYS_I2C_SOFT	/* I2C bit-banged	*/
+#ifdef CONFIG_SYS_I2C_SOFT
+#define CONFIG_SYS_I2C_SOFT_SPEED	100000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0x7F
+
 /* Configure data and clock pins for pio */
 # define I2C_INIT { \
 	at91_set_pio_output(AT91_PIO_PORTB, 4, 0); \
@@ -140,7 +139,7 @@
 /* Set clock pin */
 # define I2C_SCL(bit)		at91_set_pio_value(AT91_PIO_PORTB, 5, bit)
 # define I2C_DELAY		udelay(2) /* 1/4 I2C clock duration */
-#endif /* CONFIG_SOFT_I2C */
+#endif /* CONFIG_SYS_I2C_SOFT */
 
 /*
  * BOOTP options
diff --git a/include/configs/p1_p2_rdb_pc.h b/include/configs/p1_p2_rdb_pc.h
index 2fa537291b..d0a6b1757f 100644
--- a/include/configs/p1_p2_rdb_pc.h
+++ b/include/configs/p1_p2_rdb_pc.h
@@ -536,7 +536,6 @@
 /* I2C */
 #define CONFIG_FSL_I2C			/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C			/* I2C with hardware support */
-#undef CONFIG_SOFT_I2C			/* I2C bit-banged */
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_I2C_CMD_TREE
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C spd and slave address */
diff --git a/include/configs/p3p440.h b/include/configs/p3p440.h
index a19de079b6..3c33da73bb 100644
--- a/include/configs/p3p440.h
+++ b/include/configs/p3p440.h
@@ -98,7 +98,6 @@
  * I2C
  *----------------------------------------------------------------------*/
 #define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
 #define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
 #define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed and slave address	*/
 #define CONFIG_SYS_I2C_SLAVE		0x7F
diff --git a/include/configs/pcs440ep.h b/include/configs/pcs440ep.h
index 1897619058..6358104c1a 100644
--- a/include/configs/pcs440ep.h
+++ b/include/configs/pcs440ep.h
@@ -140,7 +140,6 @@
  * I2C
  *----------------------------------------------------------------------*/
 #define CONFIG_HARD_I2C		1	    /* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			    /* I2C bit-banged		*/
 #define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
 #define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed and slave address	*/
 #define CONFIG_SYS_I2C_SLAVE		0x7F
diff --git a/include/configs/pdnb3.h b/include/configs/pdnb3.h
index 1e073177ed..9aa112a261 100644
--- a/include/configs/pdnb3.h
+++ b/include/configs/pdnb3.h
@@ -281,12 +281,10 @@
  */
 
 /* enable I2C and select the hardware/software driver */
-#undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define	CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
-
-#define CONFIG_SYS_I2C_SPEED		83000	/* 83 kHz is supposed to work	*/
-#define CONFIG_SYS_I2C_SLAVE		0xFE
-
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	83000	/* 83 kHz is supposed to work */
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 /*
  * Software (bit-bang) I2C driver configuration
  */
diff --git a/include/configs/quad100hd.h b/include/configs/quad100hd.h
index 5f1bb581ff..30a8c5519f 100644
--- a/include/configs/quad100hd.h
+++ b/include/configs/quad100hd.h
@@ -153,7 +153,6 @@
  * I2C
  *----------------------------------------------------------------------*/
 #define CONFIG_HARD_I2C		1		/* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C				/* I2C bit-banged		*/
 #define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
 #define CONFIG_SYS_I2C_SPEED		400000		/* I2C speed and slave address	*/
 #define CONFIG_SYS_I2C_SLAVE		0x7F
diff --git a/include/configs/s5p_goni.h b/include/configs/s5p_goni.h
index 56e83478f8..89ae32b215 100644
--- a/include/configs/s5p_goni.h
+++ b/include/configs/s5p_goni.h
@@ -226,8 +226,10 @@
 #define CONFIG_SOFT_I2C_GPIO_SCL s5pc110_gpio_get_nr(j4, 3)
 #define CONFIG_SOFT_I2C_GPIO_SDA s5pc110_gpio_get_nr(j4, 0)
 
-#define CONFIG_SOFT_I2C	1
-#define CONFIG_SYS_I2C_SPEED	50000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0x7F
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_SYS_MAX_I2C_BUS	7
 #define CONFIG_USB_GADGET
diff --git a/include/configs/s5pc210_universal.h b/include/configs/s5pc210_universal.h
index eb13bb3a67..f7266aa3a1 100644
--- a/include/configs/s5pc210_universal.h
+++ b/include/configs/s5pc210_universal.h
@@ -250,9 +250,11 @@
 #define CONFIG_SOFT_I2C_GPIO_SCL exynos4_gpio_part1_get_nr(b, 7)
 #define CONFIG_SOFT_I2C_GPIO_SDA exynos4_gpio_part1_get_nr(b, 6)
 
-#define CONFIG_SOFT_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0
 #define CONFIG_SOFT_I2C_READ_REPEATED_START
-#define CONFIG_SYS_I2C_SPEED	50000
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_SYS_MAX_I2C_BUS	7
 
diff --git a/include/configs/sacsng.h b/include/configs/sacsng.h
index 54d55a0a1e..efbf6b69f0 100644
--- a/include/configs/sacsng.h
+++ b/include/configs/sacsng.h
@@ -296,15 +296,13 @@
  * If the software driver is chosen, there are some additional
  * configuration items that the driver uses to drive the port pins.
  */
-#undef  CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
-#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	400000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0x7F
 /*
  * Software (bit-bang) I2C driver configuration
  */
-#ifdef CONFIG_SOFT_I2C
 #define I2C_PORT	3		/* Port A=0, B=1, C=2, D=3 */
 #define I2C_ACTIVE	(iop->pdir |=  0x00010000)
 #define I2C_TRISTATE	(iop->pdir &= ~0x00010000)
@@ -314,7 +312,6 @@
 #define I2C_SCL(bit)	if(bit) iop->pdat |=  0x00020000; \
 			else    iop->pdat &= ~0x00020000
 #define I2C_DELAY	udelay(20)	/* 1/4 I2C clock duration */
-#endif /* CONFIG_SOFT_I2C */
 
 /* Define this to reserve an entire FLASH sector for
  * environment variables. Otherwise, the environment will be
diff --git a/include/configs/sbc405.h b/include/configs/sbc405.h
index 6e53bc2ee2..4120cf4d2a 100644
--- a/include/configs/sbc405.h
+++ b/include/configs/sbc405.h
@@ -169,7 +169,6 @@
 #define CONFIG_SYS_RX_ETH_BUFFER	16	/* use 16 rx buffer on 405 emac */
 
 #define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#undef  CONFIG_SOFT_I2C			/* I2C bit-banged		*/
 #define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
 #define CONFIG_SYS_I2C_SLAVE		0x7F
diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h
index fdc1b95e23..7a79e8c212 100644
--- a/include/configs/sbc8349.h
+++ b/include/configs/sbc8349.h
@@ -305,7 +305,6 @@
 
 /* I2C */
 #define CONFIG_HARD_I2C			/* I2C with hardware support*/
-#undef CONFIG_SOFT_I2C			/* I2C bit-banged */
 #define CONFIG_FSL_I2C
 #define CONFIG_SYS_I2C_SPEED	400000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_SLAVE	0x7F
diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h
index 148ade3568..354691a364 100644
--- a/include/configs/sbc8548.h
+++ b/include/configs/sbc8548.h
@@ -446,7 +446,6 @@
  */
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C		/* I2C with hardware support*/
-#undef	CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x50
 #define CONFIG_SYS_I2C_SLAVE		0x7F
diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h
index 0e2d17deb5..147e0ae83a 100644
--- a/include/configs/sbc8641d.h
+++ b/include/configs/sbc8641d.h
@@ -291,7 +291,6 @@
  */
 #define	CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define	CONFIG_HARD_I2C		/* I2C with hardware support*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #define CONFIG_SYS_I2C_NOPROBES        {0x69}	/* Don't probe these addrs */
diff --git a/include/configs/sc3.h b/include/configs/sc3.h
index 9dec21de6e..59636f7f77 100644
--- a/include/configs/sc3.h
+++ b/include/configs/sc3.h
@@ -247,7 +247,6 @@
  *-----------------------------------------------------------------------
  */
 #define  CONFIG_HARD_I2C		/* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
 #define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
 
 #define I2C_INIT
diff --git a/include/configs/snapper9260.h b/include/configs/snapper9260.h
index 218ca546bb..c683fab004 100644
--- a/include/configs/snapper9260.h
+++ b/include/configs/snapper9260.h
@@ -106,11 +106,11 @@
 #define CONFIG_SYS_PROMPT		"Snapper> "
 
 /* I2C - Bit-bashed */
-#define CONFIG_SOFT_I2C
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	100000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0x7F
 #define CONFIG_SOFT_I2C_READ_REPEATED_START
-#define CONFIG_I2C_MULTI_BUS
 #define I2C_INIT do {							\
 		at91_set_gpio_output(AT91_PIN_PA23, 1);			\
 		at91_set_gpio_output(AT91_PIN_PA24, 1);			\
diff --git a/include/configs/socrates.h b/include/configs/socrates.h
index 7a0b481931..19869e613a 100644
--- a/include/configs/socrates.h
+++ b/include/configs/socrates.h
@@ -237,7 +237,6 @@
  */
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
 #define CONFIG_SYS_I2C_SPEED		102124	/* I2C speed and slave address	*/
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #define CONFIG_SYS_I2C_OFFSET		0x3000
diff --git a/include/configs/spc1920.h b/include/configs/spc1920.h
index 87878d50c3..2a9b00c4ec 100644
--- a/include/configs/spc1920.h
+++ b/include/configs/spc1920.h
@@ -207,13 +207,10 @@
  */
 #if defined(CONFIG_CMD_I2C)
 /* enable I2C and select the hardware/software driver */
-#undef CONFIG_HARD_I2C                 /* I2C with hardware support    */
-#define CONFIG_SOFT_I2C                1       /* I2C bit-banged               */
-
-#define CONFIG_SYS_I2C_SPEED          93000   /* 93 kHz is supposed to work   */
-#define CONFIG_SYS_I2C_SLAVE          0xFE
-
-#ifdef CONFIG_SOFT_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	93000	/* 93 kHz is supposed to work */
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 /*
  * Software (bit-bang) I2C driver configuration
  */
@@ -229,7 +226,6 @@
 #define I2C_SCL(bit)   if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
 		       else    immr->im_cpm.cp_pbdat &= ~PB_SCL
 #define I2C_DELAY      udelay(2)       /* 1/4 I2C clock duration */
-#endif /* CONFIG_SOFT_I2C */
 #endif
 
 /*-----------------------------------------------------------------------
diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h
index 939a964e7f..b688b457d6 100644
--- a/include/configs/stxgp3.h
+++ b/include/configs/stxgp3.h
@@ -180,7 +180,6 @@
  */
 #define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
 #define CONFIG_HARD_I2C		/* I2C with hardware support*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #if 0
diff --git a/include/configs/stxssa.h b/include/configs/stxssa.h
index 96d7128d0a..4c3c08622a 100644
--- a/include/configs/stxssa.h
+++ b/include/configs/stxssa.h
@@ -200,7 +200,6 @@
  */
 #define CONFIG_FSL_I2C			/* Use FSL common I2C driver */
 #define  CONFIG_HARD_I2C		/* I2C with hardware support*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
 #define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #undef CONFIG_SYS_I2C_NOPROBES
diff --git a/include/configs/top9000.h b/include/configs/top9000.h
index 7cc65773b4..884670da25 100644
--- a/include/configs/top9000.h
+++ b/include/configs/top9000.h
@@ -201,11 +201,12 @@
 #define CONFIG_CMD_USB
 
 /* I2C support must always be enabled */
-#define CONFIG_SOFT_I2C
 #define CONFIG_CMD_I2C
-#define CONFIG_SYS_I2C_SPEED		400000
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	400000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0x7F
+
 #define I2C0_PORT			AT91_PIO_PORTA
 #define SDA0_PIN			23
 #define SCL0_PIN			24
diff --git a/include/configs/trats.h b/include/configs/trats.h
index 356d87bcab..926b209c04 100644
--- a/include/configs/trats.h
+++ b/include/configs/trats.h
@@ -275,10 +275,12 @@
 #define CONFIG_SYS_INIT_SP_ADDR	(CONFIG_SYS_LOAD_ADDR - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_CACHELINE_SIZE       32
 
-#define CONFIG_SOFT_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	50000
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 #define CONFIG_SOFT_I2C_READ_REPEATED_START
 #define CONFIG_SYS_I2C_INIT_BOARD
-#define CONFIG_SYS_I2C_SPEED	50000
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_SOFT_I2C_MULTI_BUS
 #define CONFIG_SYS_MAX_I2C_BUS	15
diff --git a/include/configs/u8500_href.h b/include/configs/u8500_href.h
index 1bb612826e..218feeb232 100644
--- a/include/configs/u8500_href.h
+++ b/include/configs/u8500_href.h
@@ -166,7 +166,6 @@
  */
 #define CONFIG_U8500_I2C
 #undef	CONFIG_HARD_I2C			/* I2C with hardware support */
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged */
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_SYS_I2C_SPEED		100000
 #define CONFIG_SYS_I2C_SLAVE		0	/* slave addr of controller */
diff --git a/include/configs/uc100.h b/include/configs/uc100.h
index 450c98bd3a..ce122b46ec 100644
--- a/include/configs/uc100.h
+++ b/include/configs/uc100.h
@@ -464,13 +464,10 @@
  */
 
 /* enable I2C and select the hardware/software driver */
-#undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define	CONFIG_SOFT_I2C         1	/* I2C bit-banged		*/
-
-#define CONFIG_SYS_I2C_SPEED		93000	/* 93 kHz is supposed to work	*/
-#define CONFIG_SYS_I2C_SLAVE		0xFE
-
-#ifdef CONFIG_SOFT_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	93000 /* 93 kHz is supposed to work */
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0xFE
 /*
  * Software (bit-bang) I2C driver configuration
  */
@@ -486,7 +483,6 @@
 #define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
 			else    immr->im_cpm.cp_pbdat &= ~PB_SCL
 #define I2C_DELAY	udelay(2)	/* 1/4 I2C clock duration */
-#endif	/* CONFIG_SOFT_I2C */
 
 /*-----------------------------------------------------------------------
  * I2C EEPROM (24C164)
diff --git a/include/configs/utx8245.h b/include/configs/utx8245.h
index 60d1503bc3..4815664ab9 100644
--- a/include/configs/utx8245.h
+++ b/include/configs/utx8245.h
@@ -235,8 +235,7 @@ protect on ${u-boot_startaddr} ${u-boot_endaddr}"
  *------------------------------------------------------------------*/
 #if 1
 #define CONFIG_HARD_I2C		1		/* To enable I2C support	*/
-#undef  CONFIG_SOFT_I2C				/* I2C bit-banged		*/
-#define CONFIG_SYS_I2C_SPEED		400000		/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_SPEED		400000
 #define CONFIG_SYS_I2C_SLAVE		0x7F
 #endif
 
diff --git a/include/configs/vct.h b/include/configs/vct.h
index 7aeb66801e..fbdb728498 100644
--- a/include/configs/vct.h
+++ b/include/configs/vct.h
@@ -245,11 +245,10 @@
 /*
  * I2C/EEPROM
  */
-#undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
-
-#define CONFIG_SYS_I2C_SPEED		83000	/* 83 kHz is supposed to work	*/
-#define CONFIG_SYS_I2C_SLAVE		0x7f
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	83000	/* 83 kHz is supposed to work */
+#define CONFIG_SYS_I2C_SOFT_SLAVE	0x7f
 
 /*
  * Software (bit-bang) I2C driver configuration
@@ -337,7 +336,7 @@ int vct_gpio_get(int pin);
 #undef CONFIG_CMD_USB
 
 #undef CONFIG_SMC911X
-#undef CONFIG_SOFT_I2C
+#undef CONFIG_SYS_I2C_SOFT
 #undef CONFIG_SOURCE
 #undef CONFIG_SYS_LONGHELP
 #undef CONFIG_TIMESTAMP
diff --git a/include/configs/vl_ma2sc.h b/include/configs/vl_ma2sc.h
index e2cf4f005e..5c43c1bea3 100644
--- a/include/configs/vl_ma2sc.h
+++ b/include/configs/vl_ma2sc.h
@@ -147,10 +147,12 @@
 #define CONFIG_SYS_I2C_SLAVE			0		/* not used */
 
 #ifndef CONFIG_HARD_I2C
-#define CONFIG_SOFT_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SOFT			/* I2C bit-banged */
+#define CONFIG_SYS_I2C_SOFT_SPEED	CONFIG_SYS_I2C_SPEED
+#define CONFIG_SYS_I2C_SOFT_SLAVE	CONFIG_SYS_I2C_SLAVE
 
 /* Software  I2C driver configuration */
-
 #define I2C_DELAY	udelay(2500000/CONFIG_SYS_I2C_SPEED)
 
 #define AT91_PIN_SDA	(1<<4)		/* AT91C_PIO_PB4 */
diff --git a/include/configs/vme8349.h b/include/configs/vme8349.h
index f97de5490b..54fbe8bdad 100644
--- a/include/configs/vme8349.h
+++ b/include/configs/vme8349.h
@@ -239,7 +239,6 @@
 /* I2C */
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_HARD_I2C		/* I2C with hardware support*/
-#undef CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_FSL_I2C
 #define CONFIG_I2C_CMD_TREE
 #define CONFIG_SYS_I2C_SPEED	400000	/* I2C speed and slave address */
diff --git a/include/configs/zeus.h b/include/configs/zeus.h
index b0c3bd5f9b..75195bc742 100644
--- a/include/configs/zeus.h
+++ b/include/configs/zeus.h
@@ -169,7 +169,6 @@
  * I2C
  *----------------------------------------------------------------------*/
 #define CONFIG_HARD_I2C		1		/* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C				/* I2C bit-banged		*/
 #define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
 #define CONFIG_SYS_I2C_SPEED		400000		/* I2C speed and slave address	*/
 #define CONFIG_SYS_I2C_SLAVE		0x7F
diff --git a/include/i2c.h b/include/i2c.h
index 3e09af9141..f532a14431 100644
--- a/include/i2c.h
+++ b/include/i2c.h
@@ -305,6 +305,15 @@ unsigned int i2c_get_bus_speed(void);
  * Adjusts I2C pointers after U-Boot is relocated to DRAM
  */
 void i2c_reloc_fixup(void);
+#if defined(CONFIG_SYS_I2C_SOFT)
+void i2c_soft_init(void);
+void i2c_soft_active(void);
+void i2c_soft_tristate(void);
+int i2c_soft_read(void);
+void i2c_soft_sda(int bit);
+void i2c_soft_scl(int bit);
+void i2c_soft_delay(void);
+#endif
 #else
 
 /*