arm: Remove tk71 board
This board has not been converted to generic board by the deadline. Remove it. Signed-off-by: Simon Glass <sjg@chromium.org>
This commit is contained in:
parent
7650beb7ca
commit
f73db66d62
|
@ -25,9 +25,6 @@ config TARGET_DNS325
|
|||
config TARGET_ICONNECT
|
||||
bool "iconnect Board"
|
||||
|
||||
config TARGET_TK71
|
||||
bool "TK71 Board"
|
||||
|
||||
config TARGET_KM_KIRKWOOD
|
||||
bool "KM_KIRKWOOD Board"
|
||||
|
||||
|
@ -64,7 +61,6 @@ source "board/buffalo/lsxl/Kconfig"
|
|||
source "board/cloudengines/pogo_e02/Kconfig"
|
||||
source "board/d-link/dns325/Kconfig"
|
||||
source "board/iomega/iconnect/Kconfig"
|
||||
source "board/karo/tk71/Kconfig"
|
||||
source "board/keymile/km_arm/Kconfig"
|
||||
source "board/LaCie/net2big_v2/Kconfig"
|
||||
source "board/LaCie/netspace_v2/Kconfig"
|
||||
|
|
|
@ -1,12 +0,0 @@
|
|||
if TARGET_TK71
|
||||
|
||||
config SYS_BOARD
|
||||
default "tk71"
|
||||
|
||||
config SYS_VENDOR
|
||||
default "karo"
|
||||
|
||||
config SYS_CONFIG_NAME
|
||||
default "tk71"
|
||||
|
||||
endif
|
|
@ -1,6 +0,0 @@
|
|||
TK71 BOARD
|
||||
#M: -
|
||||
S: Maintained
|
||||
F: board/karo/tk71/
|
||||
F: include/configs/tk71.h
|
||||
F: configs/tk71_defconfig
|
|
@ -1,9 +0,0 @@
|
|||
#
|
||||
# Copyright (C) 2012 Marek Vasut <marex@denx.de>
|
||||
# on behalf of DENX Software Engineering GmbH
|
||||
#
|
||||
#
|
||||
# SPDX-License-Identifier: GPL-2.0+
|
||||
#
|
||||
|
||||
obj-y := tk71.o
|
|
@ -1,158 +0,0 @@
|
|||
#
|
||||
# (C) Copyright 2009
|
||||
# Marvell Semiconductor <www.marvell.com>
|
||||
# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
|
||||
#
|
||||
# adopted to TK71 by
|
||||
# Nils Faerber <nils.faerber@kernelconcepts.de>
|
||||
#
|
||||
# SPDX-License-Identifier: GPL-2.0+
|
||||
#
|
||||
# Refer doc/README.kwbimage for more details about how-to configure
|
||||
# and create kirkwood boot image
|
||||
#
|
||||
|
||||
# Boot Media configurations
|
||||
BOOT_FROM nand
|
||||
NAND_ECC_MODE default
|
||||
NAND_PAGE_SIZE 0x0800
|
||||
|
||||
# SOC registers configuration using bootrom header extension
|
||||
# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
|
||||
|
||||
# Configure RGMII-0 interface pad voltage to 1.8V
|
||||
DATA 0xFFD100e0 0x1b1b1b9b
|
||||
|
||||
#Dram initalization for SINGLE x16 CL=5 @ 400MHz
|
||||
DATA 0xFFD01400 0x43000c30 # DDR Configuration register
|
||||
# bit13-0: 0xc30 (3120 DDR2 clks refresh rate)
|
||||
# bit23-14: zero
|
||||
# bit24: 1= enable exit self refresh mode on DDR access
|
||||
# bit25: 1 required
|
||||
# bit29-26: zero
|
||||
# bit31-30: 01
|
||||
|
||||
DATA 0xFFD01404 0x36543000 # DDR Controller Control Low
|
||||
# bit 4: 0=addr/cmd in smame cycle
|
||||
# bit 5: 0=clk is driven during self refresh, we don't care for APX
|
||||
# bit 6: 0=use recommended falling edge of clk for addr/cmd
|
||||
# bit14: 0=input buffer always powered up
|
||||
# bit18: 1=cpu lock transaction enabled
|
||||
# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
|
||||
# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
|
||||
# bit30-28: 3 required
|
||||
# bit31: 0=no additional STARTBURST delay
|
||||
|
||||
DATA 0xFFD01408 0x1101355b # DDR Timing (Low) (active cycles value +1)
|
||||
# bit3-0: TRAS lsbs
|
||||
# bit7-4: TRCD
|
||||
# bit11- 8: TRP
|
||||
# bit15-12: TWR
|
||||
# bit19-16: TWTR
|
||||
# bit20: TRAS msb
|
||||
# bit23-21: 0x0
|
||||
# bit27-24: TRRD
|
||||
# bit31-28: TRTP
|
||||
|
||||
DATA 0xFFD0140C 0x00000034 # DDR Timing (High)
|
||||
# bit6-0: TRFC
|
||||
# bit8-7: TR2R
|
||||
# bit10-9: TR2W
|
||||
# bit12-11: TW2W
|
||||
# bit31-13: zero required
|
||||
|
||||
DATA 0xFFD01410 0x00000000 # DDR Address Control
|
||||
# bit1-0: 01, Cs0width=x16
|
||||
# bit3-2: 10, Cs0size=512Mb
|
||||
# bit5-4: 01, Cs1width=x16
|
||||
# bit7-6: 10, Cs1size=512Mb
|
||||
# bit9-8: 00, Cs2width=nonexistent
|
||||
# bit11-10: 00, Cs2size =nonexistent
|
||||
# bit13-12: 00, Cs3width=nonexistent
|
||||
# bit15-14: 00, Cs3size =nonexistent
|
||||
# bit16: 0, Cs0AddrSel
|
||||
# bit17: 0, Cs1AddrSel
|
||||
# bit18: 0, Cs2AddrSel
|
||||
# bit19: 0, Cs3AddrSel
|
||||
# bit31-20: 0 required
|
||||
|
||||
DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
|
||||
# bit0: 0, OpenPage enabled
|
||||
# bit31-1: 0 required
|
||||
|
||||
DATA 0xFFD01418 0x00000000 # DDR Operation
|
||||
# bit3-0: 0x0, DDR cmd
|
||||
# bit31-4: 0 required
|
||||
|
||||
DATA 0xFFD0141C 0x00000652 # DDR Mode
|
||||
# bit2-0: 2, BurstLen=2 required
|
||||
# bit3: 0, BurstType=0 required
|
||||
# bit6-4: 4, CL=5
|
||||
# bit7: 0, TestMode=0 normal
|
||||
# bit8: 0, DLL reset=0 normal
|
||||
# bit11-9: 6, auto-precharge write recovery ????????????
|
||||
# bit12: 0, PD must be zero
|
||||
# bit31-13: 0 required
|
||||
|
||||
DATA 0xFFD01420 0x00000042 # DDR Extended Mode
|
||||
# bit0: 0, DDR DLL enabled
|
||||
# bit1: 0, DDR drive strenght normal
|
||||
# bit2: 0, DDR ODT control lsd (disabled)
|
||||
# bit5-3: 000, required
|
||||
# bit6: 1, DDR ODT control msb, (disabled)
|
||||
# bit9-7: 000, required
|
||||
# bit10: 0, differential DQS enabled
|
||||
# bit11: 0, required
|
||||
# bit12: 0, DDR output buffer enabled
|
||||
# bit31-13: 0 required
|
||||
|
||||
DATA 0xFFD01424 0x0000F17F # DDR Controller Control High
|
||||
# bit2-0: 111, required
|
||||
# bit3 : 1 , MBUS Burst Chop disabled
|
||||
# bit6-4: 111, required
|
||||
# bit7 : 0
|
||||
# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz
|
||||
# bit9 : 0 , no half clock cycle addition to dataout
|
||||
# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals
|
||||
# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh
|
||||
# bit15-12: 1111 required
|
||||
# bit31-16: 0 required
|
||||
|
||||
DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values)
|
||||
DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values)
|
||||
|
||||
DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
|
||||
DATA 0xFFD01504 0x1FFFFFF1 # CS[0]n Size
|
||||
# bit0: 1, Window enabled
|
||||
# bit1: 0, Write Protect disabled
|
||||
# bit3-2: 00, CS0 hit selected
|
||||
# bit23-4: ones, required
|
||||
# bit31-24: 0x0F, Size (i.e. 256MB)
|
||||
|
||||
DATA 0xFFD01508 0x00000000 # CS[1]n Base address to 256Mb
|
||||
DATA 0xFFD0150C 0x00000000 # CS[1]n Size 256Mb Window enabled for CS1
|
||||
|
||||
DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
|
||||
DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
|
||||
|
||||
DATA 0xFFD01494 0x00110000 # DDR ODT Control (Low)
|
||||
# bit3-0: 0010, (read) M_ODT[0] is asserted during read from DRAM CS1
|
||||
# bit7-4: 0001, (read) M_ODT[1] is asserted during read from DRAM CS0
|
||||
# bit19-16: 0010, (write) M_ODT[0] is asserted during write to DRAM CS1.
|
||||
# bit23-20: 0001, (write) M_ODT[1] is asserted during write to DRAM CS0.
|
||||
DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
|
||||
# bit1-0: 00, ODT0 controlled by ODT Control (low) register above
|
||||
# bit3-2: 01, ODT1 active NEVER!
|
||||
# bit31-4: zero, required
|
||||
|
||||
DATA 0xFFD0149C 0x0000F80F # CPU ODT Control
|
||||
# bit3-0: 1111, internal ODT is asserted during read from DRAM bank 0-3
|
||||
# bit11-10: 01, M_DQ, M_DM, and M_DQS I/O buffer ODT Select: 150 ohm
|
||||
# bit13-12: 10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm
|
||||
# bit14: 1, M_STARTBURST_IN ODT: Enabled
|
||||
# bit15: 1, DDR IO ODT Unit: Use ODT block
|
||||
DATA 0xFFD01480 0x00000001 # DDR Initialization Control
|
||||
#bit0=1, enable DDR init upon this register write
|
||||
|
||||
# End of Header extension
|
||||
DATA 0x0 0x0
|
|
@ -1,150 +0,0 @@
|
|||
/*
|
||||
* Copyright (C) 2012 Marek Vasut <marex@denx.de>
|
||||
* on behalf of DENX Software Engineering GmbH
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <miiphy.h>
|
||||
#include <asm/arch/cpu.h>
|
||||
#include <asm/arch/soc.h>
|
||||
#include <asm/arch/mpp.h>
|
||||
#include <asm/io.h>
|
||||
|
||||
DECLARE_GLOBAL_DATA_PTR;
|
||||
|
||||
#define TK71_OE_LOW (~0)
|
||||
#define TK71_OE_HIGH (~0)
|
||||
#define TK71_OE_VAL_LOW (0)
|
||||
#define TK71_OE_VAL_HIGH (0)
|
||||
|
||||
int board_early_init_f(void)
|
||||
{
|
||||
/*
|
||||
* default gpio configuration
|
||||
* There are maximum 64 gpios controlled through 2 sets of registers
|
||||
* the below configuration configures mainly initial LED status
|
||||
*/
|
||||
mvebu_config_gpio(TK71_OE_VAL_LOW,
|
||||
TK71_OE_VAL_HIGH,
|
||||
TK71_OE_LOW, TK71_OE_HIGH);
|
||||
|
||||
/* Multi-Purpose Pins Functionality configuration */
|
||||
static const u32 kwmpp_config[] = {
|
||||
MPP0_NF_IO2,
|
||||
MPP1_NF_IO3,
|
||||
MPP2_NF_IO4,
|
||||
MPP3_NF_IO5,
|
||||
MPP4_NF_IO6,
|
||||
MPP5_NF_IO7,
|
||||
MPP6_SYSRST_OUTn,
|
||||
MPP7_GPO,
|
||||
MPP8_TW_SDA,
|
||||
MPP9_TW_SCK,
|
||||
MPP10_UART0_TXD,
|
||||
MPP11_UART0_RXD,
|
||||
MPP12_SD_CLK,
|
||||
MPP13_SD_CMD,
|
||||
MPP14_SD_D0,
|
||||
MPP15_SD_D1,
|
||||
MPP16_SD_D2,
|
||||
MPP17_SD_D3,
|
||||
MPP18_NF_IO0,
|
||||
MPP19_NF_IO1,
|
||||
MPP20_GE1_0,
|
||||
MPP21_GE1_1,
|
||||
MPP22_GE1_2,
|
||||
MPP23_GE1_3,
|
||||
MPP24_GE1_4,
|
||||
MPP25_GE1_5,
|
||||
MPP26_GE1_6,
|
||||
MPP27_GE1_7,
|
||||
MPP28_GPIO,
|
||||
MPP29_GPIO,
|
||||
MPP30_GE1_10,
|
||||
MPP31_GE1_11,
|
||||
MPP32_GE1_12,
|
||||
MPP33_GE1_13,
|
||||
MPP34_GPIO,
|
||||
MPP35_GPIO,
|
||||
MPP36_GPIO,
|
||||
MPP37_GPIO,
|
||||
MPP38_GPIO,
|
||||
MPP39_GPIO,
|
||||
MPP40_GPIO,
|
||||
MPP41_GPIO,
|
||||
MPP42_GPIO,
|
||||
MPP43_GPIO,
|
||||
MPP44_GPIO,
|
||||
MPP45_GPIO,
|
||||
MPP46_GPIO,
|
||||
MPP47_GPIO,
|
||||
MPP48_GPIO,
|
||||
MPP49_GPIO,
|
||||
0
|
||||
};
|
||||
kirkwood_mpp_conf(kwmpp_config, NULL);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
int board_init(void)
|
||||
{
|
||||
/*
|
||||
* arch number of board
|
||||
*/
|
||||
gd->bd->bi_arch_number = CONFIG_MACH_TYPE;
|
||||
|
||||
/* adress of boot parameters */
|
||||
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
#ifdef CONFIG_CMD_NET
|
||||
|
||||
#define MV88E1116_MAC_CTRL2_REG 21
|
||||
#define MV88E1116_PGADR_REG 22
|
||||
#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
|
||||
#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
|
||||
|
||||
static void mv_phy_88e1118_init(char *name)
|
||||
{
|
||||
u16 reg;
|
||||
u16 devadr;
|
||||
|
||||
if (miiphy_set_current_dev(name))
|
||||
return;
|
||||
|
||||
/* command to read PHY dev address */
|
||||
if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
|
||||
printf("Err..%s could not read PHY dev address\n",
|
||||
__func__);
|
||||
return;
|
||||
}
|
||||
|
||||
/*
|
||||
* Enable RGMII delay on Tx and Rx for CPU port
|
||||
* Ref: sec 4.7.2 of chip datasheet
|
||||
*/
|
||||
miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
|
||||
miiphy_read(name, devadr, MV88E1116_MAC_CTRL2_REG, ®);
|
||||
reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
|
||||
miiphy_write(name, devadr, MV88E1116_MAC_CTRL2_REG, reg);
|
||||
miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
|
||||
|
||||
/* reset the phy */
|
||||
miiphy_reset(name, devadr);
|
||||
|
||||
printf("88E1118 Initialized on %s\n", name);
|
||||
}
|
||||
|
||||
/* Configure and enable Switch and PHY */
|
||||
void reset_phy(void)
|
||||
{
|
||||
/* configure and initialize PHY */
|
||||
mv_phy_88e1118_init("egiga0");
|
||||
|
||||
}
|
||||
#endif
|
|
@ -1,6 +0,0 @@
|
|||
CONFIG_ARM=y
|
||||
CONFIG_KIRKWOOD=y
|
||||
CONFIG_TARGET_TK71=y
|
||||
# CONFIG_CMD_IMLS is not set
|
||||
# CONFIG_CMD_FLASH is not set
|
||||
# CONFIG_CMD_SETEXPR is not set
|
|
@ -1,112 +0,0 @@
|
|||
/*
|
||||
* Copyright (C) 2012 Marek Vasut <marex@denx.de>
|
||||
* on behalf of DENX Software Engineering GmbH
|
||||
*
|
||||
* SPDX-License-Identifier: GPL-2.0+
|
||||
*/
|
||||
|
||||
#ifndef __CONFIG_TK71_H__
|
||||
#define __CONFIG_TK71_H__
|
||||
|
||||
/*
|
||||
* Version number information
|
||||
*/
|
||||
#define CONFIG_IDENT_STRING "\nKa-Ro TK71"
|
||||
|
||||
/*
|
||||
* High Level Configuration Options (easy to change)
|
||||
*/
|
||||
#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
|
||||
#define CONFIG_KW88F6281 1 /* SOC Name */
|
||||
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
|
||||
#define CONFIG_NR_DRAM_BANKS 1
|
||||
|
||||
#define MACH_TYPE_TK71 2399
|
||||
#define CONFIG_MACH_TYPE MACH_TYPE_TK71
|
||||
|
||||
/*
|
||||
* Commands configuration
|
||||
*/
|
||||
#define CONFIG_SYS_HUSH_PARSER
|
||||
|
||||
#define CONFIG_SYS_NO_FLASH
|
||||
#define CONFIG_DOS_PARTITION
|
||||
#define CONFIG_SUPPORT_VFAT
|
||||
|
||||
#define CONFIG_CMD_DHCP
|
||||
#define CONFIG_CMD_ENV
|
||||
#define CONFIG_CMD_EXT2
|
||||
#define CONFIG_CMD_FAT
|
||||
#define CONFIG_CMD_MTDPARTS
|
||||
#define CONFIG_CMD_NAND
|
||||
#define CONFIG_CMD_PING
|
||||
#define CONFIG_CMD_USB
|
||||
|
||||
/*
|
||||
* mv-common.h should be defined after CMD configs since it used them
|
||||
* to enable certain macros
|
||||
*/
|
||||
#include "mv-common.h"
|
||||
|
||||
/*
|
||||
* NAND flash
|
||||
*/
|
||||
#ifdef CONFIG_CMD_NAND
|
||||
#define CONFIG_MTD_DEVICE
|
||||
#define CONFIG_MTD_PARTITIONS
|
||||
#define CONFIG_JFFS2_NAND
|
||||
#define CONFIG_JFFS2_DEV "nand0,3"
|
||||
#endif
|
||||
|
||||
/*
|
||||
* Ethernet Driver configuration
|
||||
*/
|
||||
#ifdef CONFIG_CMD_NET
|
||||
#define CONFIG_MVGBE_PORTS {1, 0}
|
||||
#define CONFIG_PHY_BASE_ADR 0x08
|
||||
#endif
|
||||
|
||||
/*
|
||||
* USB/EHCI
|
||||
*/
|
||||
#ifdef CONFIG_CMD_USB
|
||||
#define CONFIG_USB_EHCI
|
||||
#define CONFIG_USB_EHCI_KIRKWOOD
|
||||
#define CONFIG_EHCI_IS_TDI
|
||||
#define CONFIG_USB_STORAGE
|
||||
#endif
|
||||
|
||||
/*
|
||||
* Environment variables configurations
|
||||
*/
|
||||
#ifdef CONFIG_CMD_NAND
|
||||
#define CONFIG_ENV_IS_IN_NAND
|
||||
#define CONFIG_ENV_SECT_SIZE 0x20000
|
||||
#else
|
||||
#define CONFIG_ENV_IS_NOWHERE
|
||||
#endif
|
||||
|
||||
#define CONFIG_ENV_SIZE 0x20000
|
||||
#define CONFIG_ENV_ADDR 0x80000
|
||||
#define CONFIG_ENV_OFFSET 0x80000
|
||||
|
||||
/*
|
||||
* Default environment variables
|
||||
*/
|
||||
#define CONFIG_BOOTCOMMAND "nand read 0x800000 kernel 0x300000; bootm;"
|
||||
#define CONFIG_MTDPARTS "512K(u-boot),512K(u-boot-env),3M(kernel),-(root)"
|
||||
#define CONFIG_EXTRA_ENV_SETTINGS \
|
||||
"update_uboot=dhcp u-boot.kwb; nand erase.part u-boot; nand write ${fileaddr} u-boot ${filesize}\0" \
|
||||
"update_kernel=dhcp uImage-tk71; nand erase.part kernel; nand write ${fileaddr} kernel ${filesize} \0" \
|
||||
"update_rootfs=dhcp rootfs-tk71; nand erase.part root; nand write ${fileaddr} root ${filesize}\0" \
|
||||
"update_all=run update_uboot; run update_kernel; run update_rootfs; reset\0" \
|
||||
"mtdids=nand0=orion_nand\0" \
|
||||
"mtdparts=mtdparts=orion_nand:"CONFIG_MTDPARTS"\0" \
|
||||
"bootargs=console=ttyS0,115200 mtdparts=orion_nand:"CONFIG_MTDPARTS" rootfstype=jffs2 root=/dev/mtdblock3 rw\0"
|
||||
#define MTDIDS_DEFAULT "nand0=orion_nand"
|
||||
#define MTDPARTS_DEFAULT "mtdparts=orion_nand:"CONFIG_MTDPARTS
|
||||
|
||||
#define PHYS_SDRAM_1 0x00000000 /* Base address */
|
||||
#define PHYS_SDRAM_1_SIZE 0x20000000 /* Max 512 MB RAM */
|
||||
|
||||
#endif /* __CONFIG_TK71_H__ */
|
Loading…
Reference in a new issue