Current driver always performs a phy soft reset when connecting the phy
device, but soft reset is not always supported by a phy device, so
introduce a quirk PHY_FLAG_BROKEN_RESET to let such a phy device to skip
soft reset. This commit uses 'flags' of phy device structure to store the
quirk.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This new function will allow MAC drivers to override supported
capabilities of the phy. It is required when MAC cannot handle all
speeds supported by phy.
For example phy supports up-to 1Gb connections while MAC may only work
in modes up to 100 or even 10 Mbit/sec.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Breakdown the PHY_*_FEATURES into per speed defines such that we can
easily re-use them individually.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Code is taken from Linux kernel driver (v4.2).
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
commit 3c6928fd7b "net: phy: fix warnings with W=1" caused
some PHYs(e.g. CS4315/CS4340) not working. This patch fixes the
warning and make those special PHYs working as well.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
When driver model is used for Ethernet a few functions are passed a udevice
instead of an eth_device. Also add a function to find a PHY type given its
name. This will be used to decode the device tree node.
Finally, put a phy_interface field in struct eth_pdata since this is an
important part of the platform data for Ethernet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch supports AQ1202, AQ2104, AQR105 PHY.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support for Cortina CS4315/CS4340 10G PHY.
- This driver loads CS43xx firmware from NOR/NAND/SPI/SD device
to initialize Cortina PHY.
- Cortina PHY has non-standard offset of PHY ID registers, thus
we define own get_phy_id() to override default get_phy_id().
- To define macro CONFIG_PHY_CORTINA will enable this driver.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As auto-negotiation is not supported for 2.5G SGMII, we need
to add a new type PHY_INTERFACE_MODE_SGMII_2500 to differentiate
SGMII-1G and SGMII-2.5G with different setting for auto-negotiation.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Marvell MV78460 eval board DB-78460-BP seems to need a longer
PHY autonegotiation timeout than the "standard" 4 seconds. So lets
make this timeout configurable. If not defined in the board config
header the original 4000ms is used.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Messages to afleming@freescale.com now bounce, and should be
directed to my personal address at afleming@gmail.com
Signed-off-by: Andy Fleming <afleming@gmail.com>
Add a prototype for board_phy_config() to fix the following sparse warning:
wandboard.c:200:5: warning: symbol 'board_phy_config' was not declared. Should it be static?
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Some phys (Micrel) has extended registers that must be
accessed in a special way. Add pointers to the phy driver
structure to allow to use these functions with mdio command.
Signed-off-by: Stefano Babic <sbabic@denx.de>
fixed-link is used in kernel for PHY-less MAC, so introduce this
structure that U-boot can use it to fixup dtb dynamically.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
The VSC8574 is a quad-port Gigabit Ethernet transceiver with four SerDes
interfaces for quad-port dual media capability. This driver supports SGMII
and QSGMII MAC mode. For now SGMII mode is tested.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Adds an ET1011C PHY driver which is derived from the
Linux kernel PHY driver (drivers/net/phy/et1011c.c)
from the v3.9-rc2 tag. Note that an errata workaround
config option is implemented to allow for TX_CLK to be
enabled even when gigabit mode is negotiated. This
workaround is used on the PG1.0 TI814X EVM.
Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
It is useful to be able to try a range of
possible phy addresses to connect.
Also, an ethernet device is not required
to use phy_find_by_mask leading to better
separation of mii vs ethernet, as suggested
by Andy Fleming.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Add the gigabit phy KSZ9021.
Also, add function ksz9021_phy_extended_write
/_read for access to the phys extended registers.
The environment variable "disable_giga"
can be used to disable 1000baseTx.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
This trivial change removes a compilation warning:
----8<----
phy.c: In function 'phy_init':
phy.c:448:2: warning: implicit declaration of function 'phy_smsc_init'
----8<----
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
The work-around for P4080 erratum SERDES9 says that the SERDES receiver
lanes should be reset after the XAUI starts tranmitting alignment signals.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The tsec driver had a bunch of PHY drivers already written. This
converts them all into PHY Lib drivers, and serves as the first
set of PHY drivers for PHY Lib.
While doing that, cleaned up a number of magic numbers (though
not all of them, as PHY vendors like to keep their numbers as
magical as possible). Also, noticed that almost all of the
vitesse/cicada PHYs had the same config/parse/startup functions,
so those have been collapsed into one.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
Extends the mii_dev structure to participate in a full-blown MDIO and
PHY driver scheme. The mii_dev structure and miiphy calls are modified
in such a way to allow the original mii command and miiphy
infrastructure to work as before, but also to support a new set of APIs
which allow (among other things) sharing of PHY driver code and 10G support
The mii command will continue to support normal PHY management functions
(Clause 22 of 802.3), but will not be changed to support 10G
(Clause 45).
The basic design is similar to PHY Lib from Linux, but simplified for
U-Boot's network and driver infrastructure.
We now have MDIO drivers and PHY drivers
An MDIO driver provides:
read
write
reset
A PHY driver provides:
(optionally): probe
config - initial setup, starting of auto-negotiation
startup - waiting for AN, and reading link state
shutdown - any cleanup needed
The ethernet drivers interact with the PHY Lib using these functions:
phy_connect()
phy_config()
phy_startup()
phy_shutdown()
Each PHY driver can be configured separately, or all at once using
config_phylib_all_drivers.h (added in the patch which adds the drivers)
We also provide generic drivers for Clause 22 (10/100/1000), and
Clause 45 (10G) PHYs.
We also implement phy_reset(), and call it in phy_connect(). Because
phy_reset() is essentially the same as miiphy_reset, but:
a) must support 10G PHYs, and
b) should use the phylib primitives,
we implement miiphy_reset, using phy_reset(), but only when
CONFIG_PHYLIB is set. Otherwise, we just use the old version. In this
way, we save on compile size, even if we don't manage to save code size.
Pulled ethtool.h and mdio.h from:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
782d640afd15af7a1faf01cfe566ca4ac511319d
With many, many deletions so as to enable compilation under u-boot
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
Siva Durga Prasad Paladugu