For secure boot, a header is used to identify key table, signature
and image address. A new header structure is added for lsch3.
Currently key extension (IE) feature is not supported. Single key
feature is not supported. Keys must be in table format. Hence, SRK
(key table) must be present. Max key number has increase from 4 to
8. The 8th key is irrevocable. A new barker Code is used.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add configs for various IPs used during secure boot. Add address
and endianness for SEC and Security Monitor. SRK are fuses in SFP
(fuses for public key's hash). These are stored in little endian
format.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In LS2080, SFP has version 3.4. It is in little endian. The base
address is 0x01e80200. SFP is used in Secure Boot to read fuses.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
NULL pointer should be checked before any dereference. This patch
move memest after the NULL pointer check.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reported-by: Jose Rivera <german.rivera@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Free dflt_dpio pointer after its usage during error handling
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reported-by: Jose Rivera <german.rivera@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The qspi_cfg register is set by PBI when booting from QSPI. No need
to changing it again.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Implement i2c_idle_bus in driver, then setup_i2c can
be dropped for boards which enable DM_I2C/DM_GPIO/PINCTRL.
The i2c_idle_bus force bus idle flow follows setup_i2c in
arch/arm/imx-common/i2c-mxv7.c
This patch is an implementation following linux kernel patch:
"
commit 1c4b6c3bcf30d0804db0d0647d8ebeb862c6f7e5
Author: Gao Pan <b54642@freescale.com>
Date: Fri Oct 23 20:28:54 2015 +0800
i2c: imx: implement bus recovery
Implement bus recovery methods for i2c-imx so we can recover from
situations where SCL/SDA are stuck low.
Once i2c bus SCL/SDA are stuck low during transfer, config the i2c
pinctrl to gpio mode by calling pinctrl sleep set function, and then
use GPIO to emulate the i2c protocol to send nine dummy clock to recover
i2c device. After recovery, set i2c pinctrl to default group setting.
"
See Documentation/devicetree/bindings/i2c/i2c-imx.txt for detailed
description.
1. Introuduce scl_gpio/sda_gpio/bus in mxc_i2c_bus.
2. Discard the __weak attribute for i2c_idle_bus and implement it,
since we have pinctrl driver/driver model gpio driver. We can
use device tree, but not let board code to do this.
3. gpio state for mxc_i2c is not a must, but it is recommended. If
there is no gpio state, driver will give tips, but not fail.
4. The i2c controller was first probed, default pinctrl state will
be used, so when need to use gpio function, need to do
"pinctrl_select_state(dev, "gpio")" and after force bus idle,
need to switch back "pinctrl_select_state(dev, "default")".
This is example about how to use the gpio force bus
idle function:
"
&i2c1 {
clock-frequency = <100000>;
pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1>;
pinctrl-1 = <&pinctrl_i2c1_gpio>;
scl-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
sda-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
status = "okay";
[....]
};
[.....]
pinctrl_i2c1_gpio: i2c1grp_gpio {
fsl,pins = <
MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x1b8b0
MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x1b8b0
>;
};
"
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: York Sun <york.sun@nxp.com>
fw_senten/fw_printenv can be compiled as a tools library,
excluding the fw_env_main object.
Reported-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
dma_addr_t holds any valid DMA address. If the DMA API only uses 32-bit
addresses, dma_addr_t need only be 32 bits wide. Bus addresses, e.g., PCI BARs,
may be wider than 32 bits, but drivers do memory-mapped I/O to ioremapped
kernel virtual addresses, so they don't care about the size of the actual
bus addresses.
Also 32 bit ARM systems with LPAE enabled can use 64bit address space, but
DMA still use 32bit address like in case of DRA7 and Keystone platforms.
This is inspired from the Linux kernel types implementation[1]
[1] https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/tree/include/linux/types.h#n142
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When switching between EFI context and U-Boot context we need to swap
the register that "gd" resides in.
Some functions slipped through here, with efi_allocate_pool / efi_free_pool
not doing the switch correctly and efi_return_handle switching too often.
Fix them all up to make sure we always have consistent register state.
Signed-off-by: Alexander Graf <agraf@suse.de>
Otherwise flash remains in read status mode and it's not possible
to access data on flash.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
SRAM is used for early stack, but kernel disables its clock on suspend.
Re-enable SRAM clock on startup, otherwise u-boot crashes on resume from suspend.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Check return value of strdup.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
The RPi3 typically uses the regular UART for high-speed communication with
the Bluetooth device, leaving us the mini UART to use for the serial
console. Add support for this UART so we can use it.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
The MAC addresses for the PRU Ethernet ports will be available in the
board EEPROM as an address range. Populate those MAC addresses (if valid)
into the u-boot environment so that they can be passed on to the
device tree during fdt_fixup_ethernet().
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some TI boards (e.g. IDK) have 4 to 6 ethernet ports and
this function is handy at board.c to configure the
MAC address of the ports.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since commit b391d74 "debug_uart: output CR along with LF", the
handling in puts() is duplicated, not to mention that it should
output carriage return before line feed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When DEBUG_RTL8169 is on, a build error occurs in function
'rtl_init': error: 'dev' undeclared. Fix this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
send_cmd response is valid only when no error happened. If an error
occured, let mmc_send_cmd() print the return value to aid debugging.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Minor change: chosen is written with one "o".
No code change here, only comment & printf.
Signed-off-by: Alexander Merkle <alexander.merkle@lauterbach.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fix typo "choosen" instead of "chosen" in pcm052.dts.
Not tested but should fix boot process and terminal output.
Signed-off-by: Alexander Merkle <alexander.merkle@lauterbach.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fix typo "choosen" instead of "chosen" in vf610-twr.dts.
Fixes boot process and terminal output for Vybrid series.
Signed-off-by: Alexander Merkle <alexander.merkle@lauterbach.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In rare circumstances two dhcp clients may generate the same
bootp ID. If this happens it is vital that the client also checks
the hw address in the received response to prevent IP address conflicts.
Signed-off-by: Anton Persson <don.juanton@gmail.com>
Fixes:
drivers/mmc/bcm2835_sdhci.c: In function ‘bcm2835_sdhci_init’:
drivers/mmc/bcm2835_sdhci.c:181:17: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Fixes:
arch/arm/mach-bcm283x/mbox.c: In function ‘bcm2835_mbox_call_prop’:
arch/arm/mach-bcm283x/mbox.c:118:48: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
arch/arm/mach-bcm283x/mbox.c:126:29: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently, CONFIG_BCM2835 is defined for all BCM283x builds and _BCM2836
is defined when building for that SoC. That means there isn't a single
define that means "exactly BCM2835". This will complicate future patches
where BCM2835-vs-anything-else needs to be determined simply.
Modify the code to define one or the other of CONFIG_BCM2835/BCM2836 so
future patches are simpler.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
It is possible to compile and run the sandbox target with clang
currently, so document that as well.
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
The bcm2835 frame buffer is in RAM, so we can easily map it as cached and gain
all the glorious performance boost that brings with it.
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Now that we have support for running with caches enabled in HYP mode,
opt in to that on the Raspberry Pi 2. This brings a significant performance
boost.
Signed-off-by: Alexander Graf <agraf@suse.de>
When compiling the code for 64bit, the lcd code emits warnings because it
tries to cast pointers to 32bit values. Fix it by casting them to longs
instead, actually properly aligning with the function prototype.
Signed-off-by: Alexander Graf <agraf@suse.de>
We currently always modify the SVC versions of registers and only support
the short descriptor PTE format.
Some boards however (like the RPi2) run in HYP mode. There, we need to modify
the HYP version of system registers and HYP mode only supports the long
descriptor PTE format.
So this patch introduces support for both long descriptor PTEs and HYP mode
registers.
Signed-off-by: Alexander Graf <agraf@suse.de>
We want to be able to reuse device drivers from 32bit code, so let's add
definitions for all the dcache options that 32bit code has.
While at it, fix up the DCACHE_OFF configuration. That was setting the bits
to declare a PTE a PTE and left the MAIR index bit at 0. Drop the useless
bits and make the index explicit.
Signed-off-by: Alexander Graf <agraf@suse.de>
Add the pinmux data for rev C evm. This is different from previous
revisions of the platform thanks to the deltas introduced both from
silicon side and from SoC side.
Based on J6EcoES2_EVM_Base_Config-20160309b and PCT-DRA72x-v1.3.0.7 for
SR2.0 silicon.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
do_set_iodelay can now be used from board files based on needs of the
platforms variation they have.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since many platforms may need different pad configuration required
depending on variation of the platform with minor deltas, it is
easier to maintain a sub step based approach to allow for pin mux
and iodelay configuration which may depend on the platform variations
and need to be done in IO isolation.
While we retain the older __recalibrate_iodelay function which provides
a ready sequencing, __recalibrate_iodelay_start and
__recalibrate_iodelay_end may be alternatively used now and the callers
will be responsible for the correct sequencing of operations.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
DDR configuration has changes from SR1.1 based Rev-A/B version of evm
to the SR2.0 based Rev C of the EVM. Rev C evm now uses the higher
density MT41K512M8RH-125-AAT:E (IT) which is of size 2GB.
Update the DDR configuration based on data from EMIF configuration
tool 1.1.1. NOTE: we use eeprom information (ram_size) to update the
configuration.
Tested-by: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Saksham Jain