1
0
Fork 0
remarkable-uboot/board/dnp5370
Bin Meng a187559e3d Use correct spelling of "U-Boot"
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2016-02-06 12:00:59 +01:00
..
Kconfig kconfig: remove redundant "string" type in arch and board Kconfigs 2014-09-13 16:43:55 -04:00
MAINTAINERS Add board MAINTAINERS files 2014-07-30 08:48:06 -04:00
Makefile Use correct spelling of "U-Boot" 2016-02-06 12:00:59 +01:00
README doc: cleanup - move board READMEs into respective board directories 2012-07-29 15:42:02 +02:00
dnp5370.c Use correct spelling of "U-Boot" 2016-02-06 12:00:59 +01:00

README

This document describes the board support for
Dil/NetPC DNP/5370 (http://www.dilnetpc.com/dnp0086.htm) module.
The distributor is SSV (http://www.ssv-embedded.de),

The module used to develop the support files contains:

*   Processor: Blackfin BF537 Rev 0.3 (600 MHz core / 120MHz RAM)

*   RAM: 32 MB SDRAM
    Hynix HY57V561620FTP-H 810EA
    Connected to Blackfin via "Expansion Bus"
    Address range 0x0000.0000 - 0x1fff.ffff

*   NOR flash: 32 MBit (4 MByte)
    Exel Semiconductor ES29LVS320EB
    Connected to Blackfin via "Expansion Bus",
    Chip Selects 0, 1 and 2, each is connected
    to a 1 MB memory bank at Blackfin, therefore
    only 3 MB accessible.
    Address range 0x2000.0000 - 0x202f.ffff
    CFI compatible

    Exel Semiconductor was bought by Rohm Semiconductor (www.rohm.com).

*   NAND flash: 64 MBit (8 MByte)
    Atmel 45DB642D-CNU
    Connected to Blackfin via SPI
    CFI compatible

*   Davicom DM9161EP Ethernet PHY

*   A SD card reader, connected via SPI

*   Hardware watchdog MAX823 or TPS3823

(other devices not listed here)

To run it, the module must be inserted in a 64 pin DIL socket
on another board, e.g. DNP/EVA13 (together: SSV SK28).

The Blackfin is booted from NOR flash. The NOR flash data begins
with the U-Boot code and is then followed by the Linux code.
Finally, the MAC is stored in the last sector.
You may need to adjust these settings to your needs.
The memory map used to develop the board support is:

Memory map:
0x00000000 .. 0x01ffffff SDRAM
0x20000000 .. 0x202fffff NOR flash

RAM use:
0x01f9bffc .. 0x01fbbffb U-Boot stack
0x01f9c000 .. 0x01f9ffff U-Boot global data
0x01fa0000 .. 0x01fbffff U-Boot malloc() RAM
0x01fc0000 .. 0x01ffffff U-Boot execution RAM

NOR flash use:
0x20000000 .. 0x0002ffff U-Boot
0x20004000 .. 0x20005fff U-Boot environment
0x20030000 .. 0x202effff Linux kernel image
0x202f0000 .. 0x202fffff MAC address sector

NOR flash is 0x00300000 (3145728) bytes large (3 MB).
Max space for compressed kernel in flash is 0x002c0000 (2883584) bytes (2.75 MB)
Max space for u-boot in flash is 0x00030000 (196608) bytes (192 KB)

The module is hardwired to BYPASS boot mode.