411 lines
13 KiB
C
411 lines
13 KiB
C
/*
|
|
* (C) Copyright 2007 DENX Software Engineering
|
|
*
|
|
* See file CREDITS for list of people who contributed to this
|
|
* project.
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License as
|
|
* published by the Free Software Foundation; either version 2 of
|
|
* the License, or (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
|
|
* MA 02111-1307 USA
|
|
*/
|
|
|
|
/*
|
|
* ADS5121 board configuration file
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
#define DEBUG
|
|
#undef DEBUG
|
|
|
|
/*
|
|
* Memory map for the ADS5121 board:
|
|
*
|
|
* 0x0000_0000 - 0x0FFF_FFFF DDR RAM (256 MB)
|
|
* 0x3000_0000 - 0x3001_FFFF SRAM (128 KB)
|
|
* 0x8000_0000 - 0x803F_FFFF IMMR (4 MB)
|
|
* 0x8200_0000 - 0x8200_001F CPLD (32 B)
|
|
* 0xFC00_0000 - 0xFFFF_FFFF NOR Boot FLASH (64 MB)
|
|
*/
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
*/
|
|
#define CONFIG_E300 1 /* E300 Family */
|
|
#define CONFIG_MPC512X 1 /* MPC512X family */
|
|
|
|
#undef CONFIG_PCI
|
|
|
|
#define CFG_MPC512X_CLKIN 66000000 /* in Hz */
|
|
|
|
#define CONFIG_BOARD_EARLY_INIT_F /* call board_early_init_f() */
|
|
|
|
#define CFG_IMMR 0x80000000
|
|
|
|
#define CFG_MEMTEST_START 0x00200000 /* memtest region */
|
|
#define CFG_MEMTEST_END 0x00400000
|
|
|
|
/*
|
|
* DDR Setup - manually set all parameters as there's no SPD etc.
|
|
*/
|
|
#define CFG_DDR_SIZE 256 /* MB */
|
|
#define CFG_DDR_BASE 0x00000000 /* DDR is system memory*/
|
|
#define CFG_SDRAM_BASE CFG_DDR_BASE
|
|
|
|
/* DDR Controller Configuration
|
|
|
|
SYS_CFG:
|
|
[31:31] MDDRC Soft Reset: Diabled
|
|
[30:30] DRAM CKE pin: Enabled
|
|
[29:29] DRAM CLK: Enabled
|
|
[28:28] Command Mode: Enabled (For initialization only)
|
|
[27:25] DRAM Row Select: dram_row[15:0] = magenta_address[25:10]
|
|
[24:21] DRAM Bank Select: dram_bank[1:0] = magenta_address[11:10]
|
|
[20:19] Read Test: DON'T USE
|
|
[18:18] Self Refresh: Enabled
|
|
[17:17] 16bit Mode: Disabled
|
|
[16:13] Ready Delay: 2
|
|
[12:12] Half DQS Delay: Disabled
|
|
[11:11] Quarter DQS Delay: Disabled
|
|
[10:08] Write Delay: 2
|
|
[07:07] Early ODT: Disabled
|
|
[06:06] On DIE Termination: Disabled
|
|
[05:05] FIFO Overflow Clear: DON'T USE here
|
|
[04:04] FIFO Underflow Clear: DON'T USE here
|
|
[03:03] FIFO Overflow Pending: DON'T USE here
|
|
[02:02] FIFO Underlfow Pending: DON'T USE here
|
|
[01:01] FIFO Overlfow Enabled: Enabled
|
|
[00:00] FIFO Underflow Enabled: Enabled
|
|
TIME_CFG0
|
|
[31:16] DRAM Refresh Time: 0 CSB clocks
|
|
[15:8] DRAM Command Time: 0 CSB clocks
|
|
[07:00] DRAM Precharge Time: 0 CSB clocks
|
|
TIME_CFG1
|
|
[31:26] DRAM tRFC:
|
|
[25:21] DRAM tWR1:
|
|
[20:17] DRAM tWRT1:
|
|
[16:11] DRAM tDRR:
|
|
[10:05] DRAM tRC:
|
|
[04:00] DRAM tRAS:
|
|
TIME_CFG2
|
|
[31:28] DRAM tRCD:
|
|
[27:23] DRAM tFAW:
|
|
[22:19] DRAM tRTW1:
|
|
[18:15] DRAM tCCD:
|
|
[14:10] DRAM tRTP:
|
|
[09:05] DRAM tRP:
|
|
[04:00] DRAM tRPA */
|
|
|
|
#define CFG_MDDRC_SYS_CFG 0xF8604200
|
|
#define CFG_MDDRC_SYS_CFG_RUN 0xE8604200
|
|
#define CFG_MDDRC_SYS_CFG_EN 0x30000000
|
|
#define CFG_MDDRC_TIME_CFG0 0x0000281E
|
|
#define CFG_MDDRC_TIME_CFG0_RUN 0x01F4281E
|
|
#define CFG_MDDRC_TIME_CFG1 0x54EC1168
|
|
#define CFG_MDDRC_TIME_CFG2 0x35210864
|
|
|
|
#define CFG_MICRON_NOP 0x01380000
|
|
#define CFG_MICRON_PCHG_ALL 0x01100400
|
|
#define CFG_MICRON_MR 0x01000022
|
|
#define CFG_MICRON_EM2 0x01020000
|
|
#define CFG_MICRON_EM3 0x01030000
|
|
#define CFG_MICRON_EN_DLL 0x01010000
|
|
#define CFG_MICRON_RST_DLL 0x01000932
|
|
#define CFG_MICRON_RFSH 0x01080000
|
|
#define CFG_MICRON_INIT_DEV_OP 0x01000832
|
|
#define CFG_MICRON_OCD_DEFAULT 0x01010780
|
|
#define CFG_MICRON_OCD_EXIT 0x01010400
|
|
|
|
/* DDR Priority Manager Configuration */
|
|
#define CFG_MDDRCGRP_PM_CFG1 0x000777AA
|
|
#define CFG_MDDRCGRP_PM_CFG2 0x00000055
|
|
#define CFG_MDDRCGRP_HIPRIO_CFG 0x00000000
|
|
#define CFG_MDDRCGRP_LUT0_MU 0x11111117
|
|
#define CFG_MDDRCGRP_LUT0_ML 0x7777777A
|
|
#define CFG_MDDRCGRP_LUT1_MU 0x4444EEEE
|
|
#define CFG_MDDRCGRP_LUT1_ML 0xEEEEEEEE
|
|
#define CFG_MDDRCGRP_LUT2_MU 0x44444444
|
|
#define CFG_MDDRCGRP_LUT2_ML 0x44444444
|
|
#define CFG_MDDRCGRP_LUT3_MU 0x55555555
|
|
#define CFG_MDDRCGRP_LUT3_ML 0x55555558
|
|
#define CFG_MDDRCGRP_LUT4_MU 0x11111111
|
|
#define CFG_MDDRCGRP_LUT4_ML 0x1111117C
|
|
#define CFG_MDDRCGRP_LUT0_AU 0x33333377
|
|
#define CFG_MDDRCGRP_LUT0_AL 0x7777EEEE
|
|
#define CFG_MDDRCGRP_LUT1_AU 0x11111111
|
|
#define CFG_MDDRCGRP_LUT1_AL 0x11111111
|
|
#define CFG_MDDRCGRP_LUT2_AU 0x11111111
|
|
#define CFG_MDDRCGRP_LUT2_AL 0x11111111
|
|
#define CFG_MDDRCGRP_LUT3_AU 0x11111111
|
|
#define CFG_MDDRCGRP_LUT3_AL 0x11111111
|
|
#define CFG_MDDRCGRP_LUT4_AU 0x11111111
|
|
#define CFG_MDDRCGRP_LUT4_AL 0x11111111
|
|
|
|
/*
|
|
* NOR FLASH on the Local Bus
|
|
*/
|
|
#define CFG_FLASH_CFI /* use the Common Flash Interface */
|
|
#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
|
|
#define CFG_FLASH_BASE 0xFC000000 /* start of FLASH */
|
|
#define CFG_FLASH_SIZE 0x04000000 /* max flash size in bytes */
|
|
#define CFG_FLASH_USE_BUFFER_WRITE
|
|
|
|
#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
|
|
#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE}
|
|
#define CFG_MAX_FLASH_SECT 256 /* max sectors per device */
|
|
|
|
#undef CFG_FLASH_CHECKSUM
|
|
|
|
/*
|
|
* CPLD registers area is really only 32 bytes in size, but the smallest possible LP
|
|
* window is 64KB
|
|
*/
|
|
#define CFG_CPLD_BASE 0x82000000
|
|
#define CFG_CPLD_SIZE 0x00010000 /* 64 KB */
|
|
|
|
#define CFG_SRAM_BASE 0x30000000
|
|
#define CFG_SRAM_SIZE 0x00020000 /* 128 KB */
|
|
|
|
#define CFG_CS0_CFG 0x05059310 /* ALE active low, data size 4bytes */
|
|
#define CFG_CS2_CFG 0x05059010 /* ALE active low, data size 1byte */
|
|
|
|
/* Use SRAM for initial stack */
|
|
#define CFG_INIT_RAM_ADDR CFG_SRAM_BASE /* Initial RAM address */
|
|
#define CFG_INIT_RAM_END CFG_SRAM_SIZE /* End of used area in RAM */
|
|
|
|
#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */
|
|
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
|
|
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
|
|
|
|
#define CFG_MONITOR_BASE TEXT_BASE /* Start of monitor */
|
|
#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
|
|
#define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
|
|
|
|
/*
|
|
* Serial Port
|
|
*/
|
|
#define CONFIG_CONS_INDEX 1
|
|
#undef CONFIG_SERIAL_SOFTWARE_FIFO
|
|
|
|
/*
|
|
* Serial console configuration
|
|
*/
|
|
#define CONFIG_PSC_CONSOLE 3 /* console is on PSC3 */
|
|
#if CONFIG_PSC_CONSOLE != 3
|
|
#error CONFIG_PSC_CONSOLE must be 3
|
|
#endif
|
|
#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
|
|
#define CFG_BAUDRATE_TABLE \
|
|
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
|
|
|
|
#define CONSOLE_FIFO_TX_SIZE FIFOC_PSC3_TX_SIZE
|
|
#define CONSOLE_FIFO_TX_ADDR FIFOC_PSC3_TX_ADDR
|
|
#define CONSOLE_FIFO_RX_SIZE FIFOC_PSC3_RX_SIZE
|
|
#define CONSOLE_FIFO_RX_ADDR FIFOC_PSC3_RX_ADDR
|
|
|
|
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
|
|
/* Use the HUSH parser */
|
|
#define CFG_HUSH_PARSER
|
|
#ifdef CFG_HUSH_PARSER
|
|
#define CFG_PROMPT_HUSH_PS2 "> "
|
|
#endif
|
|
|
|
/* I2C */
|
|
#define CONFIG_HARD_I2C /* I2C with hardware support */
|
|
#undef CONFIG_SOFT_I2C /* so disable bit-banged I2C */
|
|
#define CONFIG_I2C_MULTI_BUS
|
|
#define CONFIG_I2C_CMD_TREE
|
|
#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */
|
|
#define CFG_I2C_SLAVE 0x7F
|
|
#if 0
|
|
#define CFG_I2C_NOPROBES {{0,0x69}} * Don't probe these addrs */
|
|
#endif
|
|
|
|
/*
|
|
* Ethernet configuration
|
|
*/
|
|
#define CONFIG_MPC512x_FEC 1
|
|
#define CONFIG_NET_MULTI
|
|
#define CONFIG_PHY_ADDR 0x1
|
|
#define CONFIG_MII 1 /* MII PHY management */
|
|
#define CONFIG_ETHADDR 00:e0:5e:00:e5:14
|
|
|
|
#if 0
|
|
/*
|
|
* Configure on-board RTC
|
|
*/
|
|
#define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */
|
|
#define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */
|
|
#endif
|
|
|
|
/*
|
|
* Environment
|
|
*/
|
|
#define CFG_ENV_IS_IN_FLASH 1
|
|
/* This has to be a multiple of the Flash sector size */
|
|
#define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
|
|
#define CFG_ENV_SIZE 0x2000
|
|
#define CFG_ENV_SECT_SIZE 0x40000 /* one sector (256K) for env */
|
|
|
|
/* Address and size of Redundant Environment Sector */
|
|
#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE)
|
|
#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
|
|
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
|
|
|
|
#if defined(CONFIG_PCI)
|
|
#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
|
|
| CFG_CMD_PCI \
|
|
| CFG_CMD_NET \
|
|
| CFG_CMD_PING \
|
|
)
|
|
#else
|
|
#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
|
|
| CFG_CMD_NET \
|
|
| CFG_CMD_PING \
|
|
| CFG_CMD_MII \
|
|
| CFG_CMD_I2C)
|
|
#endif
|
|
|
|
#include <cmd_confdefs.h>
|
|
|
|
/*
|
|
* Watchdog timeout = CFG_WATCHDOG_VALUE * 65536 / IPS clock.
|
|
* For example, when IPS is set to 66MHz and CFG_WATCHDOG_VALUE is set
|
|
* to 0xFFFF, watchdog timeouts after about 64s. For details refer
|
|
* to chapter 36 of the MPC5121e Reference Manual.
|
|
*/
|
|
#define CONFIG_WATCHDOG /* enable watchdog */
|
|
#define CFG_WATCHDOG_VALUE 0xFFFF
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#define CFG_LONGHELP /* undef to save memory */
|
|
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
|
|
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
|
|
|
|
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
|
|
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
|
|
|
|
#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) /* Print Buffer Size */
|
|
#define CFG_MAXARGS 16 /* max number of command args */
|
|
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
|
|
#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
|
|
|
|
/* Cache Configuration */
|
|
#define CFG_DCACHE_SIZE 32768
|
|
#define CFG_CACHELINE_SIZE 32
|
|
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
|
|
#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
|
|
#endif
|
|
|
|
#define CFG_HID0_INIT 0x000000000
|
|
#define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK
|
|
#define CFG_HID2 HID2_HBE
|
|
|
|
/*
|
|
* Internal Definitions
|
|
*
|
|
* Boot Flags
|
|
*/
|
|
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
|
|
#define BOOTFLAG_WARM 0x02 /* Software reboot */
|
|
|
|
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
|
|
#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
|
|
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
|
|
#endif
|
|
|
|
/*
|
|
* Environment Configuration
|
|
*/
|
|
#define CONFIG_ENV_OVERWRITE
|
|
|
|
#define CONFIG_HOSTNAME ads5121
|
|
#define CONFIG_ROOTPATH /nfsroot/rootfs
|
|
#define CONFIG_BOOTFILE uImage
|
|
|
|
#define CONFIG_IPADDR 192.168.160.77
|
|
#define CONFIG_SERVERIP 192.168.1.1
|
|
#define CONFIG_GATEWAYIP 192.168.1.1
|
|
#define CONFIG_NETMASK 255.255.0.0
|
|
|
|
#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
|
|
|
|
//#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
|
|
#define CONFIG_BOOTDELAY -1
|
|
#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
|
|
|
|
#define CONFIG_BAUDRATE 115200
|
|
|
|
#define CONFIG_PREBOOT "echo;" \
|
|
"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
|
|
"echo"
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"netdev=eth0\0" \
|
|
"nfsargs=setenv bootargs root=/dev/nfs rw " \
|
|
"nfsroot=${serverip}:${rootpath}\0" \
|
|
"ramargs=setenv bootargs root=/dev/ram rw\0" \
|
|
"addip=setenv bootargs ${bootargs} " \
|
|
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
|
|
":${hostname}:${netdev}:off panic=1\0" \
|
|
"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
|
|
"flash_nfs=run nfsargs addip addtty;" \
|
|
"bootm ${kernel_addr}\0" \
|
|
"flash_self=run ramargs addip addtty;" \
|
|
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
|
|
"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
|
|
"bootm\0" \
|
|
"load=tftp 100000 /tftpboot/ads5121/u-boot.bin\0" \
|
|
"update=protect off fff00000 fff3ffff; " \
|
|
"era fff00000 fff3ffff; cp.b 100000 fff00000 ${filesize}\0" \
|
|
"upd=run load;run update\0" \
|
|
""
|
|
|
|
#define CONFIG_NFSBOOTCOMMAND \
|
|
"setenv bootargs root=/dev/nfs rw " \
|
|
"nfsroot=$serverip:$rootpath " \
|
|
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
|
|
"console=$consoledev,$baudrate $othbootargs;" \
|
|
"tftp $loadaddr $bootfile;" \
|
|
"tftp $fdtaddr $fdtfile;" \
|
|
"bootm $loadaddr - $fdtaddr"
|
|
|
|
#define CONFIG_RAMBOOTCOMMAND \
|
|
"setenv bootargs root=/dev/ram rw " \
|
|
"console=$consoledev,$baudrate $othbootargs;" \
|
|
"tftp $ramdiskaddr $ramdiskfile;" \
|
|
"tftp $loadaddr $bootfile;" \
|
|
"tftp $fdtaddr $fdtfile;" \
|
|
"bootm $loadaddr $ramdiskaddr $fdtaddr"
|
|
|
|
#define CONFIG_BOOTCOMMAND "run flash_self"
|
|
|
|
#endif /* __CONFIG_H */
|