# Bescor MP101 Libre

Notes on using the Bescor MP101 motorized pan head hardware
with libre software.

No proprietary applications, SDKs, or similar are used.

![Photo of Bescor MP101 motorized pan head.](img/bescor-mp101.jpg)


# Development Setup
The development setup is using a LattePanda 3. It is an Intel
based board with an Arduino Leonardo built on board.

This should be similar to using other Arduino devices plugged
into USB ports.


# Pins
Pins on the MP-101 cable.
Starting at "7PM", just after the key, going clockwise:

```
Use	Color	Pin	ArduinoPin		Raspberry Pi 4 B Pin
---	-----	---	--------		--------------------
Speed	Yellow	1	? PWM			12 GPIO18
Left	White	2	D0			 3 GPIO2 (Orange)
Down	Brown	3	D1			 5 GPIO3
5V	Green	4	5V, second from left.	 2 5V
Up	Blue	5	D2			 8 GPIO14
Right	Black	6	D3			10 GPIO15
GND	Red	7	GND under ICSP		 7 GND
```

The "ArduinoPin" column is how the Arduino pins on the Panda are labelled.

On the Raspberry Pi 4, with Raspbian installed running `pinout` will
majickally print the pinouts.

# Wire Harness
I made a quick and dirty wire harness that works.
My MP101 kit came with two extension cables.
I used one of those to use the male headed to plug
into the MP101, and the newly cut wires to connect
to pins to plug into the Panda Arduino.
I had short jumper wires with pin headers on each end.
For the Panda male/male wire with headers is needed.
If the board being used has pins not headers, a male/female
wire jumper will be needed.
In lieu of connecting the pins to the wires via soldering,
WAGO crimpers were used. They work great and easy++.


# Photos
![Photo of Bescor MP101 motorized pan head panel.](img/bescor-mp101-panel.jpg)
Photo of Bescor MP101 motorized pan head panel.

![Photo of Bescor MP101 motorized pan head batteries.](img/bescor-mp101-batteries.jpg)
Photo of Bescor MP101 motorized pan head battery compartment.

![Photo of Bescor MP101 motorized pan head degrees.](img/bescor-mp101-degrees.jpg)
Photo of Bescor MP101 motorized pan head rotation degrees readout.

![Photo of Bescor MP101 motorized pan head dc-6v-1a-input.](img/bescor-mp101-dc-6v-1a-input.jpg)
Photo of Bescor MP101 motorized pan head DC 6V 1A input.

![Photo of Bescor MP101 motorized pan head camera-mount.](img/bescor-mp101-camera-mount.jpg)
Photo of Bescor MP101 motorized pan head camera mount.

![Photo of Bescor MP101 motorized pan head tripod-mount.](img/bescor-mp101-tripod-mount.jpg)
Photo of Bescor MP101 motorized pan head tripod mount.

![Photo of Bescor MP101 motorized pan head remote-control.](img/bescor-mp101-remote-control.jpg)
Photo of Bescor MP101 motorized pan head remote control.

![Photo of Bescor MP101 motorized pan head cable-male.](img/bescor-mp101-cable-male.jpg)
Photo of Bescor MP101 motorized pan head male cable.

![Photo of Bescor MP101 motorized pan head cable-pins.](img/bescor-mp101-cable-pins.jpg)
Photo of Bescor MP101 motorized pan head cable pins.


# Misc
Notes.

* LattePanda3 docs say their Arduino Leonardo files are needed.

* The LattePanda3 Arduino Leonardo files are old.

* I can't get the LattePanda3 Arduino Leonardo files to work.

* The Arduino Leonardo files in Arduino 2.0.4 appear to work fine
with the LattePanda3 Leonardo. XXX


# Status
Early alpha. It moves in four directions, but doesn't stop or
have regular controls yet. Just mapped out the pins to
Arduino software.


# Disclaimer
I'm a computer sysadmin, not a video or camera expert.
This is just to explore how to use a free toolchain.


# Copyright
Unofficial project, not part of Bescor.
Upstream sources under their respective copyrights.

License: CC By SA 4.0 International and/or GPLv3+ at your discretion.

*Copyright © 2023, Jeff Moe.*