This is the latest release tag in the Xilinx repository, based on
U-Boot v2016.01 in the mainline. To sync with the Zedboard updates,
switch over to the Xilinx GitHub repository.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Matt Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This is the latest release tag in the Xilinx repository, based on
U-Boot v2016.01 in the mainline.
Commit 46d6a561be ("zedboard: Generate BOOT.BIN automatically")
switched from the Xilinx GitHub repository to the U-Boot mainline,
but this commit gets it back to the Xilinx GitHub repository for the
following reasons:
- This defconfig still relies on the Xilinx's local repository for
the kernel. The vendor does the best test for the combination of
U-Boot and the kernel with the same release tag (xilinx-v2016.2
in this case).
- At the time of commit 46d6a561be, the u-boot-xlnx still needed
manual copy of ps7_init(_gpl).c/h in order to build a working SPL
image. So, the mainline U-Boot had advantage in that point of
time. However, the improvement in the mainline U-Boot was merged
into the u-boot-xlnx at the xilinx-v2015.3 release. Now, the
mainline and the u-boot-xlnx are even in this point of view.
- The mainline U-Boot defaults to boot FIT, so something must be
done; either patch environments around with a local patch to
switch to uImage booting (current solution), or build an FIT
with a post build script (chromebook snow does this). On the
other hand, the Xilinx repository defaults to uImage booting,
so it is straightforward, and needs no addition care.
This commit does:
- Switch to the Xilinx custom git repository, and stick to the
xilinx-v2016.2 tag.
- Delete the local patch board/avnet/zedboard/uboot/0001...
since the Xilinx custom repository can boot uImage by default.
- Enable BR2_TARGET_UBOOT_FORMAT_IMG instead of ..._FORMAT_DTB_IMG
since all the Zynq boards in U-Boot enable CONFIG_OF_EMBED.
- Replace BR2_TARGET_UBOOT_ZYNQ_IMAGE with BR2_TARGET_UBOOT_SPL_NAME
since U-Boot can natively generate the Zynq boot image now. The
Zynq image support for mkimage tool was upstreamed at v2016.01
(so xilinx-v2016.1 as well), so no additional tool is needed
any more.
- Update readme.txt
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Matt Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Selecting the driver CONFIG_BRCMFMAC as built-in causes some probe issues
as we cannot guarantee that the brcmfmac driver will be probed after the
rootfs has been mounted. The brcmfmac driver retrieves the firmware and
nvram file from the rootfs, so the rootfs should be mounted first.
To avoid such issues let the CONFIG_BRCMFMAC be built as module, which is
the original option in imx_v6_v7_defconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Also bump the pc samples since they're tied to the (base) qemu config.
Results table:
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.7 2.6.0 YES OK (3)
arm_versatile 4.7 2.5.0 YES OK
arm_vexpress 4.7 2.5.0 YES OK
m68k_mcf5208 4.7 2.5.0 YES OK
m68k_q800 4.7 q800-v2.4.0 NO (2) OK
microblazebe 4.7 2.5.0 YES OK
microblazeel 4.7 2.5.0 YES OK
mips32r2el_malta 4.7 2.5.0 YES OK
mips32r2_malta 4.7 2.5.0 YES OK
mips32r6el_malta 4.7 2.6.0 YES OK (3)
mips32r6_malta 4.7 2.6.0 YES OK (3)
mips64el_malta 4.7 2.5.0 YES OK
mips64_malta 4.7 2.5.0 YES OK
mips64r6el_malta 4.7 2.6.0 YES OK (3)
mips64r6_malta 4.7 2.6.0 YES OK (3)
ppc_g3beige 4.7 2.5.0 YES OK
ppc_mpc8544ds 4.7 2.5.0 YES OK
ppc_virtex_ml507 4.7 2.5.0 NO OK
ppc64_pseries 4.7 2.5.0 YES OK
sh4 4.7 2.5.0 YES OK
sh4eb 4.7 2.5.0 NO (1) OK
sparc_ss10 4.7 2.5.0 YES OK
sparc64_sun4u 4.7 2.5.0 YES OK
sparc_sun4u 4.7 2.5.0 YES OK
x86 4.7 2.5.0 YES OK
x86_64 4.7 2.5.0 YES OK
xtensa_lx60 4.7 2.6.0 YES OK
xtensa_lx60_nommu 4.7 2.6.0 YES OK
(1) - Probably an endian issue with 8139 emulation/driver
(2) - There's a network interface, but enabling it in qemu fails
(3) - Known to fail with qemu versions lower than 2.6.0
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Currently warpboard uses a 4.0.5 kernel version from github.
Move to version 4.4.15, which is a long term supported kernel version.
With 4.4.15 we no longer need the extra two kernel patches as they have
already been upstreamed.
Use a linux fragment file, so that wireless can be functional by default.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Generate an sdcard.img image to make it easier the deployment of a
Buildroot image.
[Peter: drop unneeded exit statement in post-image script]
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add support for Technexion's i.MX6UL Pico board running U-boot 2016.07
and kernel 4.7.
For information about this board, please visit:
http://www.wandboard.org/images/hobbit/hobbitboard-imx6ul-reva1.pdf
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
With this config you can bootup a Linux kernel
in GDB simulator and test Blackfin kernel and
userland.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
As reported in bug #9091, the U-Boot environment we provide for the
Microzed and Zedboard platforms loads the ramdisk at 0x2000000 and the
DT at 0x3000000. This means that a large enough ramdisk overwrites the
DT. It makes more sense to load the DT at 0x2000000 and the ramdisk at
0x3000000.
Reported-by: Michael Monaghan <michaellmonaghan@gmail.com>
Tested-by: Michael Monaghan <michaellmonaghan@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The uCP1020 product family (ucp1020) is an Arcturus Networks Inc.
System on Modules product featuring a Freescale P1020 CPU,
optionally populated with 1 or 2 Gig-Ethernet PHYs,
DDR3, NOR Flash, eMMC NAND Flash and/or SPI Flash.
Signed-off-by: Oleksandr G Zhadan <oleks@arcturusnetworks.com>
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- fix disablehpd bug (thanks to Thomas for spotting it.)
- change default HDMI mode to 1080p60hz.
- add support for HDMI HotPlug Detection control.
- add support for mason timer.
- add support for headless boot
Signed-off-by: Dagg Stompler <daggs@gmx.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The TS-4800 is supported by mainline Linux as of 4.5 and by U-boot
as of v2016-07.
The package requires the custom ts4800-mbrboot routine.
A post-image script is provided to generate an image that can be
directly written to an SD card.
More details on the board here:
http://wiki.embeddedarm.com/wiki/TS-4800
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Patrick Keroulas <patrick.keroulas@savoirfairelinux.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Bump U-Boot version to 2016.07 and also remove the extra patch
as it is already part of U-Boot mainline now.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump U-Boot version to 2016.07 and also remove the extra patch
as it is already part of U-Boot mainline now.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Now that we've merged nodm, the autologin display manager, we can
get rid of xinit, and startx hack and use nodm to start X on boot.
While here, let's start xterm and glmark2, just as demos.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
No significant changes but 4.6.3 moved parts of the device tree
into a different file, so dts patch must be updated.
[Peter: explicitly configure kernel headers for 4.6]
Signed-off-by: Alex Suykov <alex.suykov@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Chromebook Snow (Samsung XE303C12) is an Exynos 5 board with
a keyboard, an 11 inch screen and a battery attached.
It is relatively developer-friendly and can run mainline Linux
kernels with little to no effort.
There is barely anything special about this target as far as toolchain
is concerned, but its bootloader only accepts signed kernel images
in a Chromium OS specific format, and is not controllable otherwise.
This config provides a script for building the proper kernel blobs,
and a short manual for booting Buildroot images on this device.
In-tree exynos_defconfig is used for the kernel, with a fragment
to change mwifiex into a module. When built statically, mwifiex
attempts to load its firmware before rootfs is mounted and fails.
[Peter: use BR2_KERNEL_HEADERS_AS_KERNEL=y, lock kernel version,
enable fit support in u-boot mkimage]
Signed-off-by: Alex Suykov <alex.suykov@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The console problem goes away with qemu 2.6.0 so it seems it's now a
requirement, update readme.txt accordingly.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
As described by http://linux-sunxi.org/Bootable_SD_card#SD_Card_Layout
The space betweem 544KB..1MB is reserved / used for the u-boot environment,
so mark it as such to make sure genimage doesn't put other partitions here.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
As described by http://linux-sunxi.org/Bootable_SD_card#SD_Card_Layout
The space betweem 544KB..1MB is reserved / used for the u-boot environment,
so mark it as such to make sure genimage doesn't put other partitions here.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
As described by http://linux-sunxi.org/Bootable_SD_card#SD_Card_Layout
The space betweem 544KB..1MB is reserved / used for the u-boot environment,
so mark it as such to make sure genimage doesn't put other partitions here.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
According to current "include/configs/sunxi-common.h"
U-Boot environment is stored on SD-card with offset 544 kB
and its size is limited as 128 kB.
Given memory layout of sunxi boards:
1. SPL
2. U-Boot
3. U-Boot environment
4. Partitions
(see http://linux-sunxi.org/Bootable_SD_card#SD_Card_Layout for details)
we need to make sure the first real partition starts at least
with 544+128 kB offset. Adding a small safety gap let's put
the first partition with offset 1MB from the beginning of SD-card.
Otherwise current setup gets broken as soon as one saves U-Boot
environment with "saveenv" which basically overwrites FAT partition with
zImage and board no longer boots into Linux kernel.
[Peter: extend description, add padding to u-boot partition instead]
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Erico Nunes <nunes.erico@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Peter Korsgaard <peter@korsgaard.com>
Cc: Carlos Quijano <carlos@crqgestion.es>
Cc: Andi Shyti <andi@etezian.org>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Following what's done in Raspberry Pi's defconfigs, let's
unify the consoles in Minnowboard Max defconfigs, providing
consoles on HDMI and serial port.
[Peter: use tty1 like on rpi]
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add a description of the development defconfig files.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add basic support for LinkSprite pcDuino board series
including pcDuino, pcDuino-Lite, pcDuino-Lite-WiFi.
Tested on pcDuino-Lite-WiFi.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add support for i.MX25 PDK board using U-boot 2016.05 and
kernel 4.6.1.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add a new configuration for NXP i.MX51 EVK based on U-boot 2016.05
and kernel 4.6.1.
U-boot 2016.05 needs the patch c510f2e436008 ("video: ipu_common: fix build
error") that is already in mainline to fix an IPU build error.
We can remove this patch in the future when we switch to U-boot 2016.07.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Also bump the pc samples since they're tied to the (base) qemu config.
Results table:
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.5.6 2.5.0 YES OK (4)
arm_versatile 4.6.1 2.5.0 YES OK
arm_vexpress 4.6.1 2.5.0 YES OK
m68k_mcf5208 4.6.1 2.5.0 YES OK
m68k_q800 4.6.1 q800-v2.4.0 NO (3) OK
microblazebe 4.6.1 2.5.0 YES OK
microblazeel 4.6.1 2.5.0 YES OK
mips64el_malta 4.6.1 2.5.0 YES OK
mips64_malta 4.6.1 2.5.0 YES OK
mipsel_malta 4.6.1 2.5.0 YES OK
mips_malta 4.6.1 2.5.0 YES OK
ppc_g3beige 4.6.1 2.5.0 YES OK
ppc_mpc8544ds 4.6.1 2.5.0 YES OK
ppc_virtex_ml507 4.6.1 2.5.0 NO OK
ppc64_pseries 4.6.1 2.5.0 YES OK
sh4 4.6.1 2.5.0 YES OK
sh4eb 4.6.1 2.5.0 NO (1) OK
sparc_ss10 4.6.1 2.5.0 YES OK
sparc64_sun4u 4.6.1 2.5.0 YES OK
sparc_sun4u 4.6.1 2.5.0 YES OK
x86 4.6.1 2.5.0 YES OK
x86_64 4.6.1 2.5.0 YES OK
xtensa_lx60 4.6.1 2.6.0 YES OK (2)
xtensa_lx60_nommu 4.6.1 2.6.0 YES OK (2)
(1) - Probably an endian issue with 8139 emulation/driver
(2) - Linux 4.5/4.6 doesn't work with older Qemu versions
(3) - There's a network interface, but enabling it in qemu fails
(4) - Console looks dead in 4.6
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Commit 7d0b7d3c27 ("configs/beaglebone: Use genimage
to produce the SD card image") introduce genimage usage,
but forgot to add the genimage config file. Fix it.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
[Thomas: added host dosfstools to the defconfig, needed to build a SD
card image with genimage when a FAT partition is listed in the
genimage configuration.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch adds CMA to the juno's default kernel config that is in
board/arm/juno. This is critical if the user decides to config video
resolution to 1920x1080.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add two new sample defconfigs oriented towards real PC targets.
It adds two variants for BIOS and EFI boot strategy.
On the build side we enable eudev to autoload relevant kernel
modules/support when necessary.
It adds a bunch of drivers and extra filesystem support which is by no
means extensive/complete, mostly geared towards the hardware i've got at
hand to test with.
This is accomplished by adding on top of the Qemu x86_64 kernel sample
config.
Build connman since by using eudev network interfaces get renamed on
boot thus complicating any form of automatic and friendly bringup.
It also makes Wi-Fi configuration/support easier.
In principle these base defconfigs should work just fine for other
storage media != pendrive like sata or ssd disk, however driver support
isn't there quite yet, and pendrive is mostly supported by usb storage
plus the usual usb host controller drivers.
Tested on old Lenovo laptop (BIOS) and Asus Zenbook (EFI).
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Update U-boot to the 2016.05 version and the kernel to 4.6.
U-boot 2016.05 needs the patch c510f2e436008 ("video: ipu_common: fix build
error") that is already in mainline to fix an IPU build error.
We can remove this patch in the future when we switch to U-boot 2016.07.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add basic support for the roseapple pi board, a SBC in a RPI form factor
with an Actions Semiconductor S500 SoC. For details, see:
http://roseapplepi.org/
The vendor kernel unfortunately needs a minor patch to build the XHCI
driver, so include it here.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Instead of hardcoding the genimage.cfg path, let's add a BOARD_DIR
variable to improve readability.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Since commit 2f37ef48e8 ("configs/imx6ulevk: Use ext4 as filesystem type")
the rootfs type is ext4, so update the readme.txt accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Enable kernel drivers for networking and add a simple
busybox config with basic network tools.
Add kernel patch from Linux git to fix hush segfaults while
using signal handler.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add support for the rpi-0, which is basically a rpi (model A+) in a
smaller form-factor.
This one does not have an ethernet port, so we just remove it from the
configuration (or we could use the existing rasbperrypi_defconfig and
suffer from a longer boot time because of the waiting for eth0).
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Extend the filesystem type to ext4.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Common readme.txt for all supported Armadeus boards.
Signed-off-by: Julien BOIBESSOT <julien.boibessot@armadeus.com>
[Thomas: minor tweaks in the readme.txt]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Results table:
Defconfig Kernel Qemu Network Status
------------------------------------------------------------------
aarch64_virt 4.5.3 2.5.0 YES OK
arm_versatile 4.5.3 2.5.0 YES OK
arm_vexpress 4.5.3 2.5.0 YES OK
m68k_mcf5208 4.5.3 2.5.0 NO SO-SO (3)
m68k_q800 4.5.3 q800-v2.4.0 NO (4) OK
microblazebe 4.5.3 2.5.0 YES OK
microblazeel 4.5.3 2.5.0 YES OK
mips64el_malta 4.5.3 2.5.0 YES OK
mips64_malta 4.5.3 2.5.0 YES OK
mipsel_malta 4.5.3 2.5.0 YES OK
mips_malta 4.5.3 2.5.0 YES OK
ppc_g3beige 4.5.3 2.5.0 YES OK
ppc_mpc8544ds 4.5.3 2.5.0 YES OK
ppc_virtex_ml507 4.5.3 2.5.0 NO OK
ppc64_pseries 4.5.3 2.5.0 YES OK
sh4 4.5.3 2.5.0 YES OK
sh4eb 4.5.3 2.5.0 NO (1) OK
sparc_ss10 4.5.3 2.5.0 YES OK
sparc64_sun4u 4.5.3 2.5.0 YES OK
sparc_sun4u 4.5.3 2.5.0 YES OK
x86 4.5.3 2.5.0 YES OK
x86_64 4.5.3 2.5.0 YES OK
xtensa_lx60 4.4.9 2.5.0 YES (2) OK
xtensa_lx60_nommu 4.4.9 2.5.0 YES (2) OK
(1) - Probably an endian issue with 8139 emulation/driver
(2) - xtensa ethernet broken in 4.5
(3) - It boots, you can login, but apps exit/crash often
(4) - There's a network interface, but enabling it in qemu fails
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Config can be used by other noMMU targets as qemu-system-m68k
with coldfire emulation.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Switch the invocation command to use virtio-blk and virtio-net for
better performance.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
It has better performance for block and net.
Enable virgl (DRM_VIRTIO_GPU) support for 3D acceleration.
And also DRM_BOCHS for better stdvga acceleration.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
It's exactly the same as the x86_64 variant so just create a symlink.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
So far identical to the rpi2 one except for the dts file as the SW runs in
32bit mode.
[Peter: extend commit message]
Signed-off-by: Ubaldo Porcheddu <ubaldo@eja.it>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The ODROID-C2 is a 64-bit quad-core single board computer(SBC) that is
one of the most cost-effective 64bit development boards available in the
ARM world.
http://www.hardkernel.com/main/products/prdt_info.php?g_code=G145457216438
[Peter: fix typos, drop neon/C++ settings, use git hash for Linux/U-Boot]
Signed-off-by: Brian Kim <brian.kim@hardkernel.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The defconfigs for the Raspberry Pi boards start a console on HDMI in
addition to the classic one on UART. Document this feature in the
readme.
Cc: Yann E. MORIN <yann.morin.1998@free.fr>
Cc: Arnout Vandecappelle <arnout@mind.be>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Acked-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This commit adds a new defconfig to build a X-based
graphical system for the Minnowboard MAX board.
* The 'openbox' windows manager is chosen because it's simple
and lightweigth.
* Basic X apps are enabled (such as xrandr, xterm), so we
can at least get a console and change video mode.
* ALSA default configuration is provided, so HDMI audio
works out-of-the-box.
* OpenGL is supported.
Tested on Minnoboard Turot (which is Minnowboard Max compatible).
[Peter: drop unneeded/specific toolchain config options]
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This commit enables support for:
* HDMI audio
* Support for user-provided EDID firmware
(useful to workaround broken monitors)
* Evdev interface
* System V IPC (required by ALSA)
The options make the system more useful.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Given Minnowboard and Minnowboard MAX boards are very similar,
it's desirable to unify the support for them.
This commit does the following:
1) Remove Minnowboard MAX's genimage.cfg, post-build.sh
and post-image.sh. These are identical to Minnowboard's.
2) Move Minnowboard MAX's linux config, and rename it.
It would be lovely to have a single kernel config file.
The kernel size penalty involved in adding support for
all the peripherals on both boards is small enough to
justify this.
However, the original Minnowboard has some GPIO buttons
that need to be registered by the kernel. This is not
upstreamed, and hence we need to use the yocto v3.8 kernel
to have this support.
3) Rename each grub config to grub-{board}.cfg.
4) Modify (the now unique) post-build script to use
a different grub config, according to the board.
5) Update both defconfigs, as per the above changes.
6) Finally, update the readme.txt.
[Peter: mention MAX in readme title]
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Let's rework the board and config files to use genimage
to generate the SD card image directly.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Add noMMU configuration running on dc233c MMUv3 core with identity
memory map.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
dc232b is MMUv2 core, dc233c is very similar MMUv3 core. MMUv3 is the
latest full MMU for xtensa, which allows running both MMU and noMMU
linux variants.
Update configuration overlay and linux config file.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Tested-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current Buildroot defconfigs for Raspberry Pi and Raspberry Pi 2
instantiate a console on tty1, which appears on HDMI. Add a console on
the serial port (ttyAMA0) to be more consistent with other defconfigs
and provide a better out-of-the-box experience to users used to have a
serial console from Buildroot defconfigs.
This requires three changes:
1. have two 'console=' entries in the kernel command line: tty1,
then ttyAMA0;
2. change BR2_TARGET_GENERIC_GETTY_PORT to "console", so it starts
a getty on the last console= passed to the kernel, ttyAMA0;
3. add a new getty on tty1 to the generated inittab.
Step 2 is actually obtained by removing BR2_TARGET_GENERIC_GETTY_PORT
entirely from the defconfigs, since "console" is the default value.
Step 3 requires a post-build script since the Buildroot makefiles can
configure only one console.
Note: instead of simply adding a new getty on ttyAMA0 (which would
work) this patch actually changes BR2_TARGET_GENERIC_GETTY_PORT to
instantiate a console on UART, then adds back tty1 via
post-build.sh. This is done only to avoid the "GENERIC_SERIAL" comment
where we instantiate an HDMI console, then instantiate a really-serial
console on another line.
The result is these two inittab lines:
console::respawn:/sbin/getty -L console 0 vt100 # GENERIC_SERIAL
tty1::respawn:/sbin/getty -L tty1 0 vt100 # HDMI console
Cc: Yann E. MORIN <yann.morin.1998@free.fr>
Cc: Arnout Vandecappelle <arnout@mind.be>
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Similar to stm32f429_disco, this commit adds a configuration for the
Cortex-M4 based STM32F469 platform.
It requires a few kernel patches, which have already been submitted
upstream, as well as a small OpenOCD patch. Besides that, it re-uses
most of what has been added for the STM32F429 platform.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Thomas:
- squash multiple patches from Lee Jones into one
- improve the readme.txt file
- sync the defconfig with the adaptations made to the stm32f429
configuration.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This commit adds a defconfig for the STM32F429 platform, which is
based on a Cortex-M4 core from ST Microelectronics. It is therefore
the first noMMU ARM platform supported in Buildroot.
This commit includes some files that will be common to several STM32
platforms (hence in board/stmicroelectronics) and some files that are
specific to the STM32F429 (hence in
board/stmicroelectronics/stm32f429-disco). More specifically, this
commit adds:
- A minimal Busybox configuration, which is small enough to boot
without causing OOM on such small noMMU platforms. The resulting
Busybox, statically linked with uClibc-ng, weights around 220
KB. For now, this file is located in board/stmicroelectronics/, but
we might consider moving it to package/busybox/ in the future if
needed.
- A post-build script that removes the mounting of /dev/pts (not
enabled in the kernel and not very useful for a system that has no
network and no X), and removes the network related init script and
configuration files (no network support).
- A flash.sh script, to perform the right OpenOCD invocations to
reflash the board.
- One small kernel patch to adjust the kernel command line in the
Device Tree, since it's the only way to do so.
- The usual readme.txt file.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Thomas:
- squashed multiple patches from Lee Jones together
- added the minimal Busybox configuration
- added the post-build script
- improved the flashing script to not hardcode the location of the
output directory
- add the small kernel patch
- improve the readme.txt file
- test on HW the resulting image, after using the internal toolchain.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Henceforth, a sdcard.img file is automatically generated. It simplifies the
procedure to generate a bootable SD card for Atmel Xplained boards.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Use genimage to generate a sd card with a fat partition (at91bootstrap,
u-boot, kernel, dtbs) and an ext4 partition (rootfs).
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Use genimage to generate a sd card with a fat partition (at91bootstrap,
u-boot, kernel, dtbs) and an ext4 partition (rootfs).
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Use genimage to generate a sd card with a fat partition (at91bootstrap,
u-boot, kernel, dtbs) and an ext4 partition (rootfs).
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Let's rework the board and config files to use genimage
to generate the SD card image directly.
[Peter: add host-mtools for genimage vfat handling]
Signed-off-by: Ezequiel GarcÃa <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
These three are Zynq boards and the build procedure is almost the
same. Having the SoC name prefix "zynq_" would be more consistent.
Also, this is the way in which the Linux Device Trees and the U-Boot
configuration files do.
This commit renames as follows:
zedboard_defconfig -> zynq_zed_defconfig
microzed_defconfig -> zynq_microzed_defconfig
xilinx_zc706_defconfig -> zynq_zc706_defconfig
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
It's useful for demo configs which have more features, like
automatically loaded (module) drivers.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
There were two readme files (one for flashing on NAND and one to create a
SD card) in different places. Merge them and update the SD card
generation part since all Xplained boards are supported and the -u
option of sfdisk is obsolete on latest versions.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
[Thomas: adjust the explanations, move the SD card section after the
NAND flash section.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Ethernet is not working, but at least you get a shell and
can test applications for m68k.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
arm_versatile kernel defconfig updated to deal with multi-platform ARM
support and driver changes.
mips(el) 32-bits is back in working order for 4.5
Results table:
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.5 2.3.0 YES OK
arm_versatile 4.5 2.3.0 YES OK
arm_vexpress 4.5 2.3.0 YES OK
microblazebe 4.5 2.3.0 YES OK
microblazeel 4.5 2.3.0 YES OK
mips64el_malta 4.5 2.3.0 YES OK
mips64_malta 4.5 2.3.0 YES OK
mipsel_malta 4.5 2.3.0 YES OK
mips_malta 4.5 2.3.0 YES OK
ppc_g3beige 4.5 2.3.0 YES OK
ppc_mpc8544ds 4.5 2.3.0 YES OK
ppc_virtex_ml507 4.5 2.3.0 NO OK
ppc64_pseries 4.5 2.3.0 YES OK
sh4 4.5 2.3.0 YES OK
sh4eb 4.5 2.3.0 NO (1) OK
sparc_ss10 4.5 2.3.0 YES OK
sparc64_sun4u 4.5 2.3.0 YES OK
sparc_sun4u 4.5 2.3.0 YES OK
x86 4.5 2.3.0 YES OK
x86_64 4.5 2.3.0 YES OK
xtensa_lx60 4.4.5 2.3.0 YES (2) OK
(1) - Probably an endian issue with 8139 emulation/driver
(2) - xtensa ethernet broken in 4.5 so stick to 4.4.x
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
* add a post-image.sh script
* update defconfig for genimage
* update readme.txt
[Peter: also add host-dosfstools dependency for vfat partition]
Signed-off-by: Phil Eichinger <phil@zankapfel.net>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
We're not trying to be minimal here, and qemu can bridge/emulate certain
usb devices, so enable the different controllers and at least usb
storage.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
We're not trying to be minimal here, and qemu can bridge/emulate certain
usb devices, so enable the different controllers and at least usb
storage.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
mxs-bootlets broke somewhere in between toolchain version bumps, leading to
boot failure.
Directly boot u-boot, as this is supported now, but it requires updated
partitioning (see readme.txt)
Drop mxs-bootlets patches, they aren't needed anymore.
Kernel is built as an uImage because the u-boot defconfig expects an
uImage on the second partition.
Tested on iMX233-OLinuXino-MINI hardware.
[Peter: adjust readme/config as suggested by Arnout]
Signed-off-by: Phil Eichinger <phil@zankapfel.net>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
It didn't make sense to keep the U-Boot scripts and post build/image
scripts under the nitrogen6x folder since they apply for all our
platforms.
Also update the readme.txt to make it clearer which defconfig should
be used depending on the platform targeted.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Also remove useless tfp410 enablement since a basic kernel driver has
been added.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump to the latest kernel with DT path adjustment because Linux
commit ca5b34100c57 ("dts, arm64: Move dts files to vendor subdirs")
moved the DT file to the vendor sub-directory.
This commit was tested with the latest model (FVP v8 Foundation
Platform 9.5 build 41), so I updated the instruction in readme.txt
corresponding to it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
VFPv3 and NEON was enabled and a readme.txt file was added.
Fixes bug #7580.
Tested on Pandaboard ES.
[Peter: use EABIhf]
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Now that all the boards have been converted to use genimage, the old
instructions on how to partition and write an SD card are useless.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Commit b3fa8e24 (configs: remove calao_snowball_defconfig) dropped the
outdated snowball defconfig, but forgot to remove the board files.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This commit adds basic configuration files for the Firefly RK3288 board.
Both minimal and demo defconfigs are added. The latter enables Qt5 with
the required Mali T76X GPU user space components.
More info about the board:
http://en.t-firefly.com/en/firenow/firefly_rk3288/specifications/
[Peter: use same-as-kernel for kernel headers]
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch adds a minimal working configuration for
Acmesystems Arietta g25.
[Peter: fix whitespace, use same-as-kernel for kernel headers version]
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
As a followup to http://patchwork.ozlabs.org/patch/548550/ fully convert
the versatile defconfig to create the dtb and update the instructions.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This config has no prospect of going into the future (by using DTS), and
qemu doesn't do a good job at emulating it (networking problems), so
drop it.
All of the ARM SMP testing duties are now in the vexpress defconfig
which is better suited/supported.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
We can use the vexpress arm defconfig to test SMP features in Qemu.
So document the necessary invocation changes to account for this, in
preparation of the arm nuri defconfig removal.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Keep arm_nuri on 3.10.x for the usual reasons.
Keep mips & mipsel (32 bits) on 4.3.x because 4.4.x fails to boot
properly (kernel stuck after the CPU cache info).
Results table:
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.4.1 2.3.0 YES OK
arm_nuri 3.10.96 2.3.0 YES(1) OK most times(2)
arm_versatile 4.4.1 2.3.0 YES OK
arm_vexpress 4.4.1 2.3.0 YES OK
microblazebe 4.4.1 2.3.0 YES OK
microblazeel 4.4.1 2.3.0 YES OK
mips64el_malta 4.4.1 2.3.0 YES OK
mips64_malta 4.4.1 2.3.0 YES OK
mipsel_malta 4.3.5 2.3.0 YES OK (4)
mips_malta 4.3.5 2.3.0 YES OK (4)
ppc_g3beige 4.4.1 2.3.0 YES OK
ppc_mpc8544ds 4.4.1 2.3.0 YES OK
ppc_virtex_ml507 4.4.1 2.3.0 NO OK
ppc64_pseries 4.4.1 2.3.0 YES OK
sh4 4.4.1 2.3.0 YES OK
sh4eb 4.4.1 2.3.0 NO(3) OK
sparc_ss10 4.4.1 2.3.0 YES OK
sparc64_sun4u 4.4.1 2.3.0 YES OK
sparc_sun4u 4.4.1 2.3.0 YES OK
x86 4.4.1 2.3.0 YES OK
x86_64 4.4.1 2.3.0 YES OK
xtensa_lx60 4.4.1 2.3.0 YES OK
(1) - Supposed to work but broken, probably Qemu emulation issue
(2) - In like 1/3 starts it fails to work properly
(3) - Probably an endian issue with 8139 emulation/driver
(4) - Kernel stuck at cpu cache details from 4.4 - 4.4.1
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The file that is actually produced is called u-boot-spl.bin, not
uboot-spl.bin.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Acked-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The Juno ARM Development Platform (ADP) is a software development
platform for ARMv8-A, it includes the Juno Versatile Express board
and an ARMv8-A reference software port available through Linaro.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Also updating the documentation with the dd instruction to flash the
bootable media.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[Peter: use tarball for Linux kernel, use 4.4 kernel headers]
Signed-off-by: Eelco Chaudron <echaudron@xiot.nl>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This is the 21st century, so enable SMP for them.
[Peter: add note to readme.txt about how emulate a SMP system in QEMU]
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Update the raspberrypi and raspberrypi2 configs to use genimage directly
to build the image.
Update the documentation to reflect this, and drop the volatile rootfs
option since it doesn't make much sense and it's not easily integrated
with the genimage configurations.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch updates the Cubieboard2 board defconfig to use newer u-boot
and linux versions, along with a few other improvements.
The other improvements were mostly backported from the recent Orange Pi
defconfig inclusion and are related to image generation.
linux-sunxi.org was used as a reference for both linux and u-boot
defconfig names.
In detail:
- Update linux to vanilla upstream -- currently 4.3.3 is the most
up-to-date. Although it lacks some features present only in the
linux-sunxi 3.4 branch, upstream support appears to be relatively mature
and is already being deployed by default by distributions such as Arch
Linux ARM.
- Update u-boot to vanilla upstream 2015.10. According to
linux-sunxi.org, upstream fully supports major functions (except NAND)
since 2015.07.
- Change image format to zImage and drop custom image generation script
in favour of genimage, as pointed out by reviewers in the Orange Pi
defconfig submission.
This was tested in a Cubieboard2 board with boot from mmc and it boots
fine to login prompt.
This has not been tested in a Cubieboard (A10) as I don't own any; the
version bumps probably apply to it although there are some differences
(lack of VFPv4 support, Cortex-A8 instead of Cortex-A7), so I have kept
the current Cubieboard defconfig and its scripts. This one has been only
build-tested.
Signed-off-by: Erico Nunes <nunes.erico@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This commit adds a configuration for the Orange Pi PC board,
<http://www.orangepi.org/orangepipc/>.
Signed-off-by: Eelco Chaudron <echaudron@xiot.nl>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Documentation is referring to nandflash.txt which doesn't exist.
Instead, readme.txt provides the instructions to flash the NAND storage.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Specify that the drive image file format is raw to avoid warnings and
restrictions.
Also switch to -drive syntax for all configs.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The arm_foundationv8_defconfig currently doesn't build because it uses
an external AArch64 toolchain that has been updated (Linaro toolchain)
and is now based on gcc 5.x. Unfortunately, Linux 3.13 is too old to
be built with gcc 5.x.
As a minimal fix to make this defconfig build again, we switch to use
the internal toolchain backend. At the time this defconfig was
introduced, there was no support for AArch64 in the internal toolchain
backend, but now that it is available, there is no reason to not use
it. This makes the defconfig also more consistent with the other
defconfigs.
Obviously, the kernel headers used to build the toolchain are set to
the fixed version 3.13, so that they match the kernel being used.
While we're at it, the readme.txt file corresponding to this defconfig
is updated. Runtime testing has been performed with the latest version
of the ARM Foundation model.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Created a readme.txt for the Intel Galileo Gen 1/2 that describes,
* How to build for the Intel Galileo Gen 1/2
* How to access the console on the Intel Galileo Gen 1/2
Signed-off-by: Ray Kinsella <ray.kinsella@intel.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Board support package includes:
* Toplevel build root configuration
* Github based 3.8.7 Kernel
* Upstream 3.8.7
* Linux 3.8.7 Kernel Driver Patches
* Linux 3.8.7 configuration
* Grub configuration
* Init Script to load modules
* genimage config to create sdcard image.
[Thomas: simplify post-image script since there is now only one call
to genimage.]
Signed-off-by: Ray Kinsella <ray.kinsella@intel.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
It contained a typo that prevented the driver from being built.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Now that uclibc-ng was bumped to version 1.0.9 nothing prevents x86
from working correctly.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
By default, with the original patch bootcmd runs sdboot before loading uEnv.txt.
Consequently, if the user change modeboot, the user's defined content is updated
too late.
By loading uEnv.txt before 'run $modeboot' the correct boot mode is used instead
of default mode.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@trabucayre.com>
Acked-By: Jan Viktorin <viktorin@rehivetech.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
ppc-mpc8544ds: switch to custom kernel config since the new 4.3-shipped
mpc85xx_basic_defconfig doesn't work with Qemu.
Incidentally while cleaning it up it now seems to work fine with newer
qemu versions.
sparc64_sun4u: ditch ne2k driver since it's useless, and add the e1000
driver which works fine.
x86: stick to 4.2.x kernels since 4.3 doesn't work right with uclibc
(any variant) based toolchains.
Results table:
Defconfig Kernel Qemu Network Status
--------------------------------------------------------------
aarch64_virt 4.3 2.3.0 YES OK
arm_nuri 3.10.93 2.3.0 NO(1) OK(2)
arm_versatile 4.3 2.3.0 YES OK
arm_vexpress 4.3 2.3.0 YES OK
microblazebe 4.3 2.3.0 YES OK
microblazeel 4.3 2.3.0 YES OK
mips64el_malta 4.3 2.3.0 YES OK
mips64_malta 4.3 2.3.0 YES OK
mipsel_malta 4.3 2.3.0 YES OK
mips_malta 4.3 2.3.0 YES OK
ppc_g3beige 4.3 2.3.0 YES OK
ppc_mpc8544ds 4.3 2.3.0 YES OK
ppc_virtex_ml507 4.3 2.3.0 NO OK
ppc64_pseries 4.3 2.3.0 YES OK
sh4 4.3 2.3.0 YES OK
sh4eb 4.3 2.3.0 NO(1) OK
sparc_ss10 4.3 2.3.0 YES OK
sparc64_sun4u 4.3 2.3.0 YES OK
sparc_sun4u 4.3 2.3.0 YES OK
x86 4.2.6 2.3.0 YES OK(3)
x86_64 4.3 2.3.0 YES OK
xtensa_lx60 4.3 2.3.0 YES OK
(1) - Supposed to work but broken, probably Qemu emulation issue
(2) - In like 1/3 runs it fails to start properly
(3) - linux 4.3.0 doesn't like uclibc-based toolchains (net issues)
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The Virtualizer Development Kit (VDK) Family for ARM Cortex Products
consists of a set of virtual prototypes that provide a virtualizer for
the ARM core variants. The VDK is a standalone package that runs on an
host computer.
[Thomas: drop the following options, which as noted by Arnout, are not
needed:
- BR2_LINUX_KERNEL_IMAGE_TARGET_CUSTOM=y
- BR2_LINUX_KERNEL_IMAGE_TARGET_NAME="Image"
- BR2_PACKAGE_BUSYBOX_SHOW_OTHERS=y.]
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Reviewed-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Also revamp the kernel config a bit to make it more featured, enabling
SATA ports and storage.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Enable the generic hda (sound) codec, necessary for qemu audio to work.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Enable the generic hda (sound) codec, necessary for qemu audio to work.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Changes:
* Update Kernel and U-Boot to the latest 2.0.6 BSP release from the
official sources.
* Add genimage config to create bootable SD card image
Signed-off-by: Gergely Imreh <imrehg@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
"/usr/bin/env bash" is used everywhere else in host tools. These are the
only remaining offenders.
Signed-off-by: Bjørn Forsman <bjorn.forsman@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Bump U-boot version to 2015.07 from the mainline repository. Since there
is SPL support for the wandboard in the U-boot 2015.07, it is now
possible to boot the same U-boot image for all wandboard variants
(solo/dual/quad).
Bump kernel version to 3.14.28_1.0.0 from the wandboard git repository.
Tested on Wandboard Solo, Wandboard Dual and Wandboard Quad.
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The Barebox, AT91Bootstrap and Linux patches for the Calao QIL A9260
board are all located in the same directory, board/calao/qil-a9260/,
with only a prefix to indicate to which component they apply.
Unfortunately, since commit 0eba4759fa
("packages: apply custom patches using *.patch instead of
<pkg>-*.patch"), the logic to apply custom patches in Barebox and
AT91Bootstrap has been changed from applying <package>-*.patch to
applying *.patch (in order to be consistent with what we do for all
packages in Buildroot).
However, this had the effect of trying to apply both the AT91Bootstrap
and Barebox patches on both packages, which obviously cannot work.
This commit fixes that by moving patches around, and switching to use
BR2_GLOBAL_PATCH_DIR for all of Barebox, AT91Bootstrap and Linux
patches.
In addition, the defconfig was not specifying explicitly which Barebox
version to use, so right now it's trying to use Barebox 2015.09, on
which the board-specific patch does not apply. So we've forced to use
Barebox 2012.08, which was the lastest release available at the time
the defconfig was initially contributed.
Cc: Gregory Hermant <gregory.hermant@calao-systems.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Both the Barebox and AT91Bootstrap patches for the Calao USB A9G20
board are located in the same directory, board/calao/usb-a9g20-lpw/,
with only a prefix making a difference between whether they apply to
Barebox or AT91Bootstrap.
Unfortunately, since commit 0eba4759fa
("packages: apply custom patches using *.patch instead of
<pkg>-*.patch"), the logic to apply custom patches in Barebox and
AT91Bootstrap has been changed from applying <package>-*.patch to
applying *.patch (in order to be consistent with what we do for all
packages in Buildroot).
However, this had the effect of trying to apply both the AT91Bootstrap
and Barebox patches on both packages, which obviously cannot work.
This commit fixes that by moving patches around, and switching to use
BR2_GLOBAL_PATCH_DIR.
Cc: Gregory Hermant <gregory.hermant@calao-systems.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This defconfig tries to fetch its kernel source code and U-Boot source
code from gitorious.org, which is not longer available. Therefore,
this defconfig has been failing to build since quite some time. Since
there's no obvious other place to grab the kernel and u-boot source
code, and the defconfig was not updated since a long time, let's
simply get rid of it.
[Peter: also drop README]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
It is based on olimex_a20_olinuxino_lime configuration. Tested on the mainline
kernel 4.1.4. It boots and the Ethernet is working at speed 1 Gbps.
[Thomas: remove ccache and optimize 2 options.]
Signed-off-by: Jan Viktorin <viktorin@rehivetech.com>
Acked-by: Francois Perrad <francois.perrad@gadz.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Linux kernel 4.2 was finally released, so bumping from 4.2-rc5 to
final release.
Updating Linux headers to 4.2 branch since they are introduced in
Buildroot as well already.
Also adding 1 back-ported patch that makes SD/MMC cards usable on AXS
boards. This patch will be a part of 4.3 (already in linux-next) and
hopefully will make its way in 4.2.1.
Once that patch appears in 4.2.x it can be removed from here.
Cc: Peter Korsgaard <peter@korsgaard.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Those scripts will support coming platforms such as iMX6SoloX or
iMX6QuadPlus.
One important change is that the bootscript now relies on U-Boot to
make the display detection in order to simplify the script.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Changes are based on Zedboard: Xilinx does not provide a specific DTS
for Microzed in the kernel tree. It is suggested [1] to use the
zynq-zed.dts and change the RAM size
[1] https://forums.xilinx.com/t5/Embedded-Linux/Microzed-default-device-tree-dts/td-p/432856
[Thomas:
- extend readme.txt to indicate why the same DTB is used for Microzed
and the Zedboard.
- add a description + Signed-off-by line in the
0001-zynq-Create-microzed-specific-U-Boot-environment.patch, by
re-using the description of the same patch for the Zedboard.]
Signed-off-by: Davide Viti <d.viti@infosolution.it>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The AXS10x Platform consists of a DesignWare AXC001 CPU
Card (with ARC 770D core) in case of AXS101 or AXC003 CPU Card
(typically with ARC HS38 core) in case of AXS103 mounted on an
ARC Software Development Platform Mainboard with DesignWare peripherals:
* SD/MMC contoller
* Gigabit network contoller
* Serial ports (8250-compatible)
* USB 2.0
* SPI
* I2C
It also houses HDMI output for external monitor connection.
For stand-alone usage of the board (with only keyboard, mouse and montor
attached) kernel console and getty made available on tty0 as well as on
serial port (ttyS3).
Note there're 2 prerequisites:
[1] u-boot: 2015.07 - fix creation of .config
http://patchwork.ozlabs.org/patch/502558/
[2] binutils: fix buildng of Linux kernel for ARCv2 ISA
http://patchwork.ozlabs.org/patch/503550/
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The U-Boot v2015.07 is required for successful out-of-the-box
build for common Xilinx Zynq boards (including Zedboard).
Signed-off-by: Jan Viktorin <viktorin@rehivetech.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This is a Xilinx Zynq (xc7z045) development board, based on Xilinx Zynq
(xc7z045).
This support is based on Avnet Zedboard defconfig/readme.
[Thomas:
- minor fixes in the readme.txt
- rename defconfig from zc706_defconfig to xilinx_zc706_defconfig.]
Signed-off-by: Jordi Montagne <jordi.montagne66@gmail.com>
Tested-by: Jean Burgat <jeanburgat33@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch changes the U-Boot's default environment to
boot Zedboard out-of-the-box from SD card.
The sdboot procedure tries to load a file system.bit into
the Zynq's PL (only if it exists). It is also possible to
alter the booting by an uEnv.txt file located on your SD card.
The uEnv.txt is a plain text file with <key>=<value> pairs
one per line.
Signed-off-by: Jan Viktorin <viktorin@rehivetech.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This patch adds a genimage config file and a post-image script for the
Wandboard, to generate a medium image "sdcard.img", ready to be booted.
The image contains the layout explained in the board readme.txt file:
U-Boot, its environment, and an Ext2 rootfs partition.
The defconfig has been slightly changed to enable this feature. Also
lighten the readme file since the config file is documented and simpler.
Tested on a Wandboard Solo.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
[Arnout: change the name of the tmp dir, and remove it before using
it.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This is largely the same as altera_sockit_defconfig.
It uses a fresher Linux and u-boot than SocKit. It also speeds the
serial port up to 115200.
The post-image script is generalized by adding
BR2_ROOTFS_POST_SCRIPT_ARGS and moving it up the altera directory.
Similarly, the readme is moved up and made more generic.
Signed-off-by: Charles Manning <cdhmanning@gmail.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Those scripts are executed by u-boot in order to detect the hardware
configuration (board, displays etc...), configure the bootargs and
device tree accordingly or update the bootloader located in NOR flash.
This update is necessary due to the kernel bump to version 3.10.53.
The rework consists of replacing the binaries by their text file
equivalent and generate the binaries from the post-build.sh script.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Allows for nicer framebuffer emulation under Qemu with the QXL xorg
driver.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This is a set of patch to add support for warpboard
(Freescale board based on imx6sl)
The patch contains :
- defconfig for warpboard
- linux patches from Fabio Estevam to fix device tree due to last change on
warpboard schematics (rev 1.12) and to fix kernel imx_v6_v7 defconfig which
use incorrect hci protocol
- specific firmware file for warpboard bluetooth
nvram : brcmfmac4330-sdio.txt
Origin of nvram config file for wifi :
https://github.com/Freescale/meta-fsl-arm-extra
[Thomas: misc rewording/improvements in the README file.]
Signed-off-by: Arthur LAMBERT <arthur@dreem.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add a defconfig for the Olimex A20-OLinuXino-Micro board, reusing most
of the A20-OLinuXino-Lime files.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The files in board/olimex/a20_olinuxino_lime/ work with minimal or no
modifications for the Olimex A20-OLinuXino-Micro board, whose support is
going to be added in a later commit.
Rename the directory to clarify it's not restricted to the Lime anymore.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Explicitly state where this information comes from.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Provide a flashing helper to properly select the sam-ba configuration
and reuse the sam-ba tcl script provided by Atmel with minimal
modifications.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
For consistency, rename atmel_xplained_defconfig to
atmel_sama5d3_xplained_mmc_defconfig as this configuration supports
booting the sama5d3 Xplained with an MMC card (as opposed to the NAND
flash).
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Now that we have a sanitised set of defconfig files, and we no longer
support non-DT setups, update and simplify the board readme file.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Floris Bos <bos@je-eigen-domein.nl>
Cc: Pascal de Bruijn <pmjdebruijn@pcode.nl>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Update to the latest stable kernel version; build an in-tree DTB; use
a in-tree defconfig; enable C++ (to match what we have in the non-DT
variant); do not install DTB overlays (this minimalist config does not
make use of them).
Generate the DTBs for both the "original" variant (A and B) and the
"Plus" variant (A+ and B+).
Drop our custom linux defconfig file now we use an in-tree one.
Signed-off-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Cc: Floris Bos <bos@je-eigen-domein.nl>
Cc: Pascal de Bruijn <pmjdebruijn@pcode.nl>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This commit adds a new defconfig for the Olimex A20 OLinuxino Lime
board, based on the 3.4.x vendor specific kernel, which allows to use
the Mali 3D acceleration for OpenGL support.
Reviewed-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Francois Perrad <francois.perrad@gadz.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This commit adds a new defconfig for the Olimex A20 OLinuxino Lime
board, based on the 4.x mainline kernel.
Reviewed-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Francois Perrad <francois.perrad@gadz.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Update most of the configs to the latest kernel version (4.1) except for
arm-nuri which is stuck.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Enable USB UHCI to be able to use usb mouse emulation for graphic
application tests.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The VIA VAB-820 board (and the AMOS-820 system built around it) is
based on Freescale i.MX6 for embedded and industrial computing.
Signed-off-by: Gergely Imreh <imrehg@gmail.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Switch to kernel 4.0.
Enable evdev for extra X testing.
Drop bloat/redundant options.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Switch to kernel 4.0.
Enable evdev for extra X testing.
Drop bloat/redundant options.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Switch to kernel 4.0.
Use a custom kernel config to avoid the caveat of a huge debug-enabled
one.
And also reduce defconfig options to avoid bloat.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Switch to kernel 4.0.
Switch kernel config to ext4, simplify to reduce bloat.
Adjust invocation to keep the framebuffer window for graphics testing.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Switch to kernel 4.0.
Switch to DTB (mandatory).
And adjust invocation to use dtb and add a little more RAM for testing.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Switch to kernel 4.0.
Remove redudant/pointless kernel options to reduce bloat.
Switch from smc9111 to rtl8139 for networking because of issues.
Enable evdev support for better x11 testing.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[Thomas: fix issues noticed by Arnout:
- Rewrap the linux/Config.in paragraph
- Revert the "is a toolchain dependency" -> "has a toolchain
dependency" change from pkg-generic.mk, as the original was
correct.]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
