1
0
Fork 0
alistair23-linux/drivers/i2c/busses/i2c-designware-core.h

329 lines
10 KiB
C
Raw Normal View History

/* SPDX-License-Identifier: GPL-2.0-or-later */
/*
* Synopsys DesignWare I2C adapter driver.
*
* Based on the TI DAVINCI I2C adapter driver.
*
* Copyright (C) 2006 Texas Instruments.
* Copyright (C) 2007 MontaVista Software Inc.
* Copyright (C) 2009 Provigent Ltd.
*/
#include <linux/i2c.h>
#define DW_IC_DEFAULT_FUNCTIONALITY (I2C_FUNC_I2C | \
I2C_FUNC_SMBUS_BYTE | \
I2C_FUNC_SMBUS_BYTE_DATA | \
I2C_FUNC_SMBUS_WORD_DATA | \
I2C_FUNC_SMBUS_BLOCK_DATA | \
I2C_FUNC_SMBUS_I2C_BLOCK)
#define DW_IC_CON_MASTER 0x1
#define DW_IC_CON_SPEED_STD 0x2
#define DW_IC_CON_SPEED_FAST 0x4
#define DW_IC_CON_SPEED_HIGH 0x6
#define DW_IC_CON_SPEED_MASK 0x6
#define DW_IC_CON_10BITADDR_SLAVE 0x8
#define DW_IC_CON_10BITADDR_MASTER 0x10
#define DW_IC_CON_RESTART_EN 0x20
#define DW_IC_CON_SLAVE_DISABLE 0x40
#define DW_IC_CON_STOP_DET_IFADDRESSED 0x80
#define DW_IC_CON_TX_EMPTY_CTRL 0x100
#define DW_IC_CON_RX_FIFO_FULL_HLD_CTRL 0x200
/*
* Registers offset
*/
#define DW_IC_CON 0x0
#define DW_IC_TAR 0x4
#define DW_IC_SAR 0x8
#define DW_IC_DATA_CMD 0x10
#define DW_IC_SS_SCL_HCNT 0x14
#define DW_IC_SS_SCL_LCNT 0x18
#define DW_IC_FS_SCL_HCNT 0x1c
#define DW_IC_FS_SCL_LCNT 0x20
#define DW_IC_HS_SCL_HCNT 0x24
#define DW_IC_HS_SCL_LCNT 0x28
#define DW_IC_INTR_STAT 0x2c
#define DW_IC_INTR_MASK 0x30
#define DW_IC_RAW_INTR_STAT 0x34
#define DW_IC_RX_TL 0x38
#define DW_IC_TX_TL 0x3c
#define DW_IC_CLR_INTR 0x40
#define DW_IC_CLR_RX_UNDER 0x44
#define DW_IC_CLR_RX_OVER 0x48
#define DW_IC_CLR_TX_OVER 0x4c
#define DW_IC_CLR_RD_REQ 0x50
#define DW_IC_CLR_TX_ABRT 0x54
#define DW_IC_CLR_RX_DONE 0x58
#define DW_IC_CLR_ACTIVITY 0x5c
#define DW_IC_CLR_STOP_DET 0x60
#define DW_IC_CLR_START_DET 0x64
#define DW_IC_CLR_GEN_CALL 0x68
#define DW_IC_ENABLE 0x6c
#define DW_IC_STATUS 0x70
#define DW_IC_TXFLR 0x74
#define DW_IC_RXFLR 0x78
#define DW_IC_SDA_HOLD 0x7c
#define DW_IC_TX_ABRT_SOURCE 0x80
#define DW_IC_ENABLE_STATUS 0x9c
#define DW_IC_CLR_RESTART_DET 0xa8
#define DW_IC_COMP_PARAM_1 0xf4
#define DW_IC_COMP_VERSION 0xf8
#define DW_IC_SDA_HOLD_MIN_VERS 0x3131312A
#define DW_IC_COMP_TYPE 0xfc
#define DW_IC_COMP_TYPE_VALUE 0x44570140
#define DW_IC_INTR_RX_UNDER 0x001
#define DW_IC_INTR_RX_OVER 0x002
#define DW_IC_INTR_RX_FULL 0x004
#define DW_IC_INTR_TX_OVER 0x008
#define DW_IC_INTR_TX_EMPTY 0x010
#define DW_IC_INTR_RD_REQ 0x020
#define DW_IC_INTR_TX_ABRT 0x040
#define DW_IC_INTR_RX_DONE 0x080
#define DW_IC_INTR_ACTIVITY 0x100
#define DW_IC_INTR_STOP_DET 0x200
#define DW_IC_INTR_START_DET 0x400
#define DW_IC_INTR_GEN_CALL 0x800
#define DW_IC_INTR_RESTART_DET 0x1000
#define DW_IC_INTR_DEFAULT_MASK (DW_IC_INTR_RX_FULL | \
DW_IC_INTR_TX_ABRT | \
DW_IC_INTR_STOP_DET)
#define DW_IC_INTR_MASTER_MASK (DW_IC_INTR_DEFAULT_MASK | \
DW_IC_INTR_TX_EMPTY)
#define DW_IC_INTR_SLAVE_MASK (DW_IC_INTR_DEFAULT_MASK | \
DW_IC_INTR_RX_DONE | \
DW_IC_INTR_RX_UNDER | \
DW_IC_INTR_RD_REQ)
#define DW_IC_STATUS_ACTIVITY 0x1
#define DW_IC_STATUS_TFE BIT(2)
#define DW_IC_STATUS_MASTER_ACTIVITY BIT(5)
#define DW_IC_STATUS_SLAVE_ACTIVITY BIT(6)
#define DW_IC_SDA_HOLD_RX_SHIFT 16
#define DW_IC_SDA_HOLD_RX_MASK GENMASK(23, DW_IC_SDA_HOLD_RX_SHIFT)
#define DW_IC_ERR_TX_ABRT 0x1
#define DW_IC_TAR_10BITADDR_MASTER BIT(12)
#define DW_IC_COMP_PARAM_1_SPEED_MODE_HIGH (BIT(2) | BIT(3))
#define DW_IC_COMP_PARAM_1_SPEED_MODE_MASK GENMASK(3, 2)
/*
* status codes
*/
#define STATUS_IDLE 0x0
#define STATUS_WRITE_IN_PROGRESS 0x1
#define STATUS_READ_IN_PROGRESS 0x2
#define TIMEOUT 20 /* ms */
/*
* operation modes
*/
#define DW_IC_MASTER 0
#define DW_IC_SLAVE 1
/*
* Hardware abort codes from the DW_IC_TX_ABRT_SOURCE register
*
* Only expected abort codes are listed here
* refer to the datasheet for the full list
*/
#define ABRT_7B_ADDR_NOACK 0
#define ABRT_10ADDR1_NOACK 1
#define ABRT_10ADDR2_NOACK 2
#define ABRT_TXDATA_NOACK 3
#define ABRT_GCALL_NOACK 4
#define ABRT_GCALL_READ 5
#define ABRT_SBYTE_ACKDET 7
#define ABRT_SBYTE_NORSTRT 9
#define ABRT_10B_RD_NORSTRT 10
#define ABRT_MASTER_DIS 11
#define ARB_LOST 12
#define ABRT_SLAVE_FLUSH_TXFIFO 13
#define ABRT_SLAVE_ARBLOST 14
#define ABRT_SLAVE_RD_INTX 15
#define DW_IC_TX_ABRT_7B_ADDR_NOACK (1UL << ABRT_7B_ADDR_NOACK)
#define DW_IC_TX_ABRT_10ADDR1_NOACK (1UL << ABRT_10ADDR1_NOACK)
#define DW_IC_TX_ABRT_10ADDR2_NOACK (1UL << ABRT_10ADDR2_NOACK)
#define DW_IC_TX_ABRT_TXDATA_NOACK (1UL << ABRT_TXDATA_NOACK)
#define DW_IC_TX_ABRT_GCALL_NOACK (1UL << ABRT_GCALL_NOACK)
#define DW_IC_TX_ABRT_GCALL_READ (1UL << ABRT_GCALL_READ)
#define DW_IC_TX_ABRT_SBYTE_ACKDET (1UL << ABRT_SBYTE_ACKDET)
#define DW_IC_TX_ABRT_SBYTE_NORSTRT (1UL << ABRT_SBYTE_NORSTRT)
#define DW_IC_TX_ABRT_10B_RD_NORSTRT (1UL << ABRT_10B_RD_NORSTRT)
#define DW_IC_TX_ABRT_MASTER_DIS (1UL << ABRT_MASTER_DIS)
#define DW_IC_TX_ARB_LOST (1UL << ARB_LOST)
#define DW_IC_RX_ABRT_SLAVE_RD_INTX (1UL << ABRT_SLAVE_RD_INTX)
#define DW_IC_RX_ABRT_SLAVE_ARBLOST (1UL << ABRT_SLAVE_ARBLOST)
#define DW_IC_RX_ABRT_SLAVE_FLUSH_TXFIFO (1UL << ABRT_SLAVE_FLUSH_TXFIFO)
#define DW_IC_TX_ABRT_NOACK (DW_IC_TX_ABRT_7B_ADDR_NOACK | \
DW_IC_TX_ABRT_10ADDR1_NOACK | \
DW_IC_TX_ABRT_10ADDR2_NOACK | \
DW_IC_TX_ABRT_TXDATA_NOACK | \
DW_IC_TX_ABRT_GCALL_NOACK)
/**
* struct dw_i2c_dev - private i2c-designware data
* @dev: driver model device node
* @base: IO registers pointer
* @cmd_complete: tx completion indicator
* @clk: input reference clock
* @pclk: clock required to access the registers
* @slave: represent an I2C slave device
* @cmd_err: run time hadware error code
* @msgs: points to an array of messages currently being transferred
* @msgs_num: the number of elements in msgs
* @msg_write_idx: the element index of the current tx message in the msgs
* array
* @tx_buf_len: the length of the current tx buffer
* @tx_buf: the current tx buffer
* @msg_read_idx: the element index of the current rx message in the msgs
* array
* @rx_buf_len: the length of the current rx buffer
* @rx_buf: the current rx buffer
* @msg_err: error status of the current transfer
* @status: i2c master status, one of STATUS_*
* @abort_source: copy of the TX_ABRT_SOURCE register
* @irq: interrupt number for the i2c master
* @adapter: i2c subsystem adapter node
* @slave_cfg: configuration for the slave device
* @tx_fifo_depth: depth of the hardware tx fifo
* @rx_fifo_depth: depth of the hardware rx fifo
* @rx_outstanding: current master-rx elements in tx fifo
* @timings: bus clock frequency, SDA hold and other timings
* @sda_hold_time: SDA hold value
* @ss_hcnt: standard speed HCNT value
* @ss_lcnt: standard speed LCNT value
* @fs_hcnt: fast speed HCNT value
* @fs_lcnt: fast speed LCNT value
* @fp_hcnt: fast plus HCNT value
* @fp_lcnt: fast plus LCNT value
* @hs_hcnt: high speed HCNT value
* @hs_lcnt: high speed LCNT value
* @acquire_lock: function to acquire a hardware lock on the bus
* @release_lock: function to release a hardware lock on the bus
* @shared_with_punit: true if this bus is shared with the SoCs PUNIT
* @disable: function to disable the controller
* @disable_int: function to disable all interrupts
* @init: function to initialize the I2C hardware
* @mode: operation mode - DW_IC_MASTER or DW_IC_SLAVE
i2c: designware: Do not allow i2c_dw_xfer() calls while suspended On most Intel Bay- and Cherry-Trail systems the PMIC is connected over I2C and the PMIC is accessed through various means by the _PS0 and _PS3 ACPI methods (power on / off methods) of various devices. This leads to suspend/resume ordering problems where a device may be resumed and get its _PS0 method executed before the I2C controller is resumed. On Cherry Trail this leads to errors like these: i2c_designware 808622C1:06: controller timed out ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion] ACPI Error: Method parse/execution failed \_SB.P18W._ON, AE_ERROR video LNXVIDEO:00: Failed to change power state to D0 But on Bay Trail this caused I2C reads to seem to succeed, but they end up returning wrong data, which ends up getting written back by the typical read-modify-write cycle done to turn on various power-resources. Debugging the problems caused by this silent data corruption is quite nasty. This commit adds a check which disallows i2c_dw_xfer() calls to happen until the controller's resume method has completed. Which turns the silent data corruption into getting these errors in dmesg instead: i2c_designware 80860F41:04: Error i2c_dw_xfer call while suspended ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion] ACPI Error: Method parse/execution failed \_SB.PCI0.GFX0._PS0, AE_ERROR Which is much better. Note the above errors are an example of issues which this patch will help to debug, the actual fix requires fixing the suspend order and this has been fixed by a different commit. Note the setting / clearing of the suspended flag in the suspend / resume methods is NOT protected by i2c_lock_bus(). This is intentional as these methods get called from i2c_dw_xfer() (through pm_runtime_get/put) a nd i2c_dw_xfer() is called with the i2c_bus_lock held, so otherwise we would deadlock. This means that there is a theoretical race between a non runtime suspend and the suspended check in i2c_dw_xfer(), this is not a problem since normally we should not hit the race and this check is primarily a debugging tool so hitting the check if there are suspend/resume ordering problems does not need to be 100% reliable. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-02-22 06:08:40 -07:00
* @suspended: set to true if the controller is suspended
*
* HCNT and LCNT parameters can be used if the platform knows more accurate
* values than the one computed based only on the input clock frequency.
* Leave them to be %0 if not used.
*/
struct dw_i2c_dev {
struct device *dev;
void __iomem *base;
void __iomem *ext;
struct completion cmd_complete;
struct clk *clk;
struct clk *pclk;
struct reset_control *rst;
struct i2c_client *slave;
u32 (*get_clk_rate_khz) (struct dw_i2c_dev *dev);
struct dw_pci_controller *controller;
int cmd_err;
struct i2c_msg *msgs;
int msgs_num;
int msg_write_idx;
u32 tx_buf_len;
u8 *tx_buf;
int msg_read_idx;
u32 rx_buf_len;
u8 *rx_buf;
int msg_err;
unsigned int status;
u32 abort_source;
int irq;
u32 flags;
struct i2c_adapter adapter;
u32 functionality;
u32 master_cfg;
u32 slave_cfg;
unsigned int tx_fifo_depth;
unsigned int rx_fifo_depth;
int rx_outstanding;
struct i2c_timings timings;
u32 sda_hold_time;
u16 ss_hcnt;
u16 ss_lcnt;
u16 fs_hcnt;
u16 fs_lcnt;
u16 fp_hcnt;
u16 fp_lcnt;
u16 hs_hcnt;
u16 hs_lcnt;
int (*acquire_lock)(void);
void (*release_lock)(void);
bool shared_with_punit;
void (*disable)(struct dw_i2c_dev *dev);
void (*disable_int)(struct dw_i2c_dev *dev);
int (*init)(struct dw_i2c_dev *dev);
int (*set_sda_hold_time)(struct dw_i2c_dev *dev);
int mode;
struct i2c_bus_recovery_info rinfo;
i2c: designware: Do not allow i2c_dw_xfer() calls while suspended On most Intel Bay- and Cherry-Trail systems the PMIC is connected over I2C and the PMIC is accessed through various means by the _PS0 and _PS3 ACPI methods (power on / off methods) of various devices. This leads to suspend/resume ordering problems where a device may be resumed and get its _PS0 method executed before the I2C controller is resumed. On Cherry Trail this leads to errors like these: i2c_designware 808622C1:06: controller timed out ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion] ACPI Error: Method parse/execution failed \_SB.P18W._ON, AE_ERROR video LNXVIDEO:00: Failed to change power state to D0 But on Bay Trail this caused I2C reads to seem to succeed, but they end up returning wrong data, which ends up getting written back by the typical read-modify-write cycle done to turn on various power-resources. Debugging the problems caused by this silent data corruption is quite nasty. This commit adds a check which disallows i2c_dw_xfer() calls to happen until the controller's resume method has completed. Which turns the silent data corruption into getting these errors in dmesg instead: i2c_designware 80860F41:04: Error i2c_dw_xfer call while suspended ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion] ACPI Error: Method parse/execution failed \_SB.PCI0.GFX0._PS0, AE_ERROR Which is much better. Note the above errors are an example of issues which this patch will help to debug, the actual fix requires fixing the suspend order and this has been fixed by a different commit. Note the setting / clearing of the suspended flag in the suspend / resume methods is NOT protected by i2c_lock_bus(). This is intentional as these methods get called from i2c_dw_xfer() (through pm_runtime_get/put) a nd i2c_dw_xfer() is called with the i2c_bus_lock held, so otherwise we would deadlock. This means that there is a theoretical race between a non runtime suspend and the suspended check in i2c_dw_xfer(), this is not a problem since normally we should not hit the race and this check is primarily a debugging tool so hitting the check if there are suspend/resume ordering problems does not need to be 100% reliable. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-02-22 06:08:40 -07:00
bool suspended;
};
#define ACCESS_SWAP 0x00000001
#define ACCESS_16BIT 0x00000002
#define ACCESS_INTR_MASK 0x00000004
#define ACCESS_NO_IRQ_SUSPEND 0x00000008
#define MODEL_CHERRYTRAIL 0x00000100
#define MODEL_MSCC_OCELOT 0x00000200
#define MODEL_MASK 0x00000f00
u32 dw_readl(struct dw_i2c_dev *dev, int offset);
void dw_writel(struct dw_i2c_dev *dev, u32 b, int offset);
int i2c_dw_set_reg_access(struct dw_i2c_dev *dev);
u32 i2c_dw_scl_hcnt(u32 ic_clk, u32 tSYMBOL, u32 tf, int cond, int offset);
u32 i2c_dw_scl_lcnt(u32 ic_clk, u32 tLOW, u32 tf, int offset);
int i2c_dw_set_sda_hold(struct dw_i2c_dev *dev);
unsigned long i2c_dw_clk_rate(struct dw_i2c_dev *dev);
int i2c_dw_prepare_clk(struct dw_i2c_dev *dev, bool prepare);
int i2c_dw_acquire_lock(struct dw_i2c_dev *dev);
void i2c_dw_release_lock(struct dw_i2c_dev *dev);
int i2c_dw_wait_bus_not_busy(struct dw_i2c_dev *dev);
int i2c_dw_handle_tx_abort(struct dw_i2c_dev *dev);
u32 i2c_dw_func(struct i2c_adapter *adap);
void i2c_dw_disable(struct dw_i2c_dev *dev);
void i2c_dw_disable_int(struct dw_i2c_dev *dev);
static inline void __i2c_dw_enable(struct dw_i2c_dev *dev)
{
dw_writel(dev, 1, DW_IC_ENABLE);
}
static inline void __i2c_dw_disable_nowait(struct dw_i2c_dev *dev)
{
dw_writel(dev, 0, DW_IC_ENABLE);
}
void __i2c_dw_disable(struct dw_i2c_dev *dev);
extern u32 i2c_dw_read_comp_param(struct dw_i2c_dev *dev);
extern int i2c_dw_probe(struct dw_i2c_dev *dev);
#if IS_ENABLED(CONFIG_I2C_DESIGNWARE_SLAVE)
extern int i2c_dw_probe_slave(struct dw_i2c_dev *dev);
#else
static inline int i2c_dw_probe_slave(struct dw_i2c_dev *dev) { return -EINVAL; }
#endif
#if IS_ENABLED(CONFIG_I2C_DESIGNWARE_BAYTRAIL)
extern int i2c_dw_probe_lock_support(struct dw_i2c_dev *dev);
#else
static inline int i2c_dw_probe_lock_support(struct dw_i2c_dev *dev) { return 0; }
#endif