Add module author, description and license to support module build.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
The audio PLL debug interface should be only registered when
the CONFIG_DEBUG_FS is enabled.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Anson Huang <anson.huang@nxp.com>
The audio pll debug interface only available on i.MX8MM,
so only register this debug interface on i.MX8MM.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Anson Huang <anson.huang@nxp.com>
for userspace monitor control of the K-divider dynamically,
we provide two interfaces to userspace: delta_k & pll_parameter
1): delta_k is used to adjust the K divider in PLL based on small
steps;
2): the pll_parameter interface is used for get PLL's current
M-divider, P-divider, S-divider & K-divider setting in PLL register
example for the usage of these two interfaces:
A): Get the current PLL setting of dividers:
root@imx8mmevk:~# cat /sys/kernel/debug/audio_pll_monitor/audio_pll1/pll_parameter
Mdiv: 0x106; Pdiv: 0x2; Sdiv: 0x3; Kdiv: 0x24dd
B): if want to adjust the K-divider by a delta_k '1', then
echo 0x1 > /sys/kernel/debug/audio_pll_monitor/audio_pll1/delta_k;
root@imx8mmevk:~# cat /sys/kernel/debug/audio_pll_monitor/audio_pll1/pll_parameter
Mdiv: 0x106; Pdiv: 0x2; Sdiv: 0x3; Kdiv: 0x24de
C): if want to adjust the K-divider by a delta_k '-1', then
echo -1 > /sys/kernel/debug/audio_pll_monitor/audio_pll1/delta_k;
root@imx8mmevk:~# cat /sys/kernel/debug/audio_pll_monitor/audio_pll1/pll_parameter
Mdiv: 0x106; Pdiv: 0x2; Sdiv: 0x3; Kdiv: 0x24dc
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
A53 CCM clk root only accepts input up to 1GHz, however
the A53 core could run above 1GHz which voliates the CCM limitation.
There is a CORE_SEL slice before A53 core, we need configure the
CORE_SEL slice source from ARM PLL, not A53 CCM clk root.
The A53 CCM clk root should only be used when need to change ARM PLL
frequency.
Add arm_a53_core clk that could source from arm_a53_div and arm_pll_out.
Configure a53 ccm root sources from 800MHz sys pll
Configure a53 core sources from arm_pll_out
Enable arm_pll_out to avoid disable the clock when set a53 core parent.
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When doing DRAM frequency change, the DRAM PLL config will
be changed in ATF side, so add 'CLK_GET_RATE_NOCACHE' flag
to make sure each time we get the DRAM PLL frequency through
'clk_get_rate' API, we can get the correct frequency.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Anson Huang <anson.huang@nxp.com>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
The 'nand_usdhc_bus' clock is only need to be enabled when usdhc
or nand module is active, so change it to non-critical clock type.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
When we need to support dual linux with jailhouse, there is no clock
controller in 2nd inmate linux cell, it relys on the first linux to
configure the clock ready and on. So we add those clocks required for
the 2nd linux in dts to make them prepare enabled, and pass
clk_ignore_unused to the 1st linux, then the 1st linux will not gated
off the clocks. So the 2nd linux could use IPs without touching clocks.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Remove the earlycon uart clocks that are hard cord in platforms
clock driver, instead of parsing the earlycon uart port from dt
and enable these clocks from clock property in dt node.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
During cpu frequency switching the main "CLK_ARM" is reparented to an
intermediate "step" clock. On imx8mm and imx8mn the 24M oscillator is
used for this purpose but it is extremely slow, increasing wakeup
latencies to the point that i2c transactions can timeout and system
becomes unresponsive.
Fix by switching the "step" clk to SYS_PLL1_800M, matching the behavior
of imx8m cpufreq drivers in imx vendor tree.
This bug was not immediately apparent because upstream arm64 defconfig
uses the "performance" governor by default so no cpufreq transitions
happen.
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Fixes: 96d6392b54 ("clk: imx: Add support for i.MX8MN clock driver")
Cc: stable@vger.kernel.org
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lkml.kernel.org/r/f5d2b9c53f1ed5ccb1dd3c6624f56759d92e1689.1571771777.git.leonard.crestez@nxp.com
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
pll BYPASS bit should be kept inside pll driver for glitchless freq
setting following spec. If exposing the bit, that means pll driver and
clk driver has two paths to touch this bit, which is wrong.
So use EXT_BYPASS bit here.
And drop uneeded set parent, because EXT_BYPASS default is 0.
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Suggested-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lkml.kernel.org/r/1568043491-20680-4-git-send-email-peng.fan@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* There is no video_pll2 on imx8mm, replace with dummy
* Replace reference to sys_pll3_clk with sys_pll3_out
* qspi parent[2] is sys_pll2_333m not sys_pll1_800m
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When of_clk_add_provider failed, all clks should be unregistered.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no strong reason for this to use CLK_OF_DECLARE instead
of being a platform driver. Plus, this will now be aligned with the
other i.MX8M clock drivers which are platform drivers.
In order to make the clock provider a platform driver
all the data and code needs to be outside of .init section.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The AUDIO PLL max support 650M, so the original clk settings violate
spec. This patch makes the output 786432000 -> 393216000,
and 722534400 -> 361267200 to aligned with NXP vendor kernel without any
impact on audio functionality and go within 650MHz PLL limit.
Cc: <stable@vger.kernel.org>
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MM has no sys3_pll2_out clock, PWM3 clock's mux option #4
should be sys_pll3_out, sys3_pll2_out is a typo, fix it.
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rename 'share_count_dcss' to 'share_count_disp', since the
DCSS module does not exist on imx8mm platform. So rename it
to avoid any unnecessary confusion.
Signed-off-by: Fancy Fang <chen.fang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per latest imx8mm datasheet of CCM, the parent of usb1_ctrl_root_clk
should be usb_bus.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
1416X/1443X PLL are used on i.MX8MM and i.MX8MN and maybe
other i.MX8M series SoC later, the macro definitions of
these PLLs' initialization should be common for usage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
side. The two main highlights in the core framework are the addition of an bulk
clk_get API that handles optional clks and an extra debugfs file that tells the
developer about the current parent of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is mostly
because that SoC has started converting to the clk_hw style of clk
registration. The next big update is in the Amlogic meson clk driver that
gained some support for audio, cpu, and temperature clks while fixing some PLL
issues. Finally, the biggest thing that stands out is the conversion of a large
part of the Allwinner sunxi-ng driver to the new clk parent scheme that uses
less strings and more pointer comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks here and
there to clk data along with the normal addition of a handful of new drivers
and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1
-----BEGIN PGP SIGNATURE-----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=mK0C
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This round of clk driver and framework updates is heavy on the driver
update side. The two main highlights in the core framework are the
addition of an bulk clk_get API that handles optional clks and an
extra debugfs file that tells the developer about the current parent
of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is
mostly because that SoC has started converting to the clk_hw style of
clk registration. The next big update is in the Amlogic meson clk
driver that gained some support for audio, cpu, and temperature clks
while fixing some PLL issues. Finally, the biggest thing that stands
out is the conversion of a large part of the Allwinner sunxi-ng driver
to the new clk parent scheme that uses less strings and more pointer
comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks
here and there to clk data along with the normal addition of a handful
of new drivers and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (190 commits)
clk: consoldiate the __clk_get_hw() declarations
clk: sprd: Add check for return value of sprd_clk_regmap_init()
clk: lochnagar: Update DT binding doc to include the primary SPDIF MCLK
clk: Add Si5341/Si5340 driver
dt-bindings: clock: Add silabs,si5341
clk: clk-si544: Implement small frequency change support
clk: add BCM63XX gated clock controller driver
devicetree: document the BCM63XX gated clock bindings
clk: at91: sckc: use dedicated functions to unregister clock
clk: at91: sckc: improve error path for sama5d4 sck registration
clk: at91: sckc: remove unnecessary line
clk: at91: sckc: improve error path for sam9x5 sck register
clk: at91: sckc: add support to free slow clock osclillator
clk: at91: sckc: add support to free slow rc oscillator
clk: at91: sckc: add support to free slow oscillator
clk: rockchip: export HDMIPHY clock on rk3228
clk: rockchip: add watchdog pclk on rk3328
clk: rockchip: add clock id for hdmi_phy special clock on rk3228
clk: rockchip: add clock id for watchdog pclk on rk3328
clk: at91: sckc: add support for SAM9X60
...
There is no audio_pll2_clk registered, it should be audio_pll2_out.
Cc: <stable@vger.kernel.org>
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This clock is used for dram operations inside TF-A and must be kept
enabled for features such as suspend/resume dram retention and busfreq
to work.
This is required for imx8mm suspend to work with NXP branch of TF-A.
There is an equivalent clk on imx8mq and it's always been marked as
critical in upstream.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is documented in the reference manuals as GIC_CLK_ROOT.
In some out-of-tree DVFS scenarios the gic clock can end up as the only
user of sys_pll2 so if we don't define the gic clk explicitly it might
be turned off.
This applies to both 8mq and 8mm: same clk register but diffferent
parents.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MM has clock gate for SNVS module, add it into clock tree
for SNVS RTC driver to manage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To Frac pll, the gate shift is 13, however to Int PLL the gate shift
is 11.
Cc: <stable@vger.kernel.org>
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX8MM has clock gate for each GPIO bank, add them
into clock tree for GPIO driver to manage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It calls another __init marked function and thus causes a section
mismatch if we don't mark it this way.
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Anson Huang