Add module author, description and license to support module build.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Add sai7_ipg_clk clock settings, fixes use of SAI7
interface on imx8mn SoC.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Adrian Alonso <adrian.alonso@nxp.com>
Fix the following warning:
drivers/clk/imx/clk-imx8mn.c: In function 'imx8mn_clocks_probe':
drivers/clk/imx/clk-imx8mn.c:609:29: warning: assignment from incompatible pointer type
clks[IMX8MN_CLK_SNVS_ROOT] = imx_clk_hw_gate4("snvs_root_clk", "ipg_root", base + 0x4470, 0);
^
Fixes: d6f385583c ("clk: imx8mn: add SNVS clock to clock tree")
Reported-by: Anthony Toubeau <anthony.toubeau@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
i.mx8mn has support for clock gating the snvs module.
Add it into clock tree so that rtc-snvs driver could use it.
Note this will also be required in the snvs_pwrkey driver,
once support for clock management will be added.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
(cherry picked from commit 16e71d4da7)
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
A53 CCM clk root only accepts input up to 1GHz, however
the A53 core could run above 1GHz which voliates the CCM limitation.
There is a CORE_SEL slice before A53 core, we need configure the
CORE_SEL slice source from ARM PLL, not A53 CCM clk root.
The A53 CCM clk root should only be used when need to change ARM PLL
frequency.
Add arm_a53_core clk that could source from arm_a53_div and arm_pll_out.
Configure a53 ccm root sources from 800MHz sys pll
Configure a53 core sources from arm_pll_out
Enable arm_pll_out to avoid disable the clock when set a53 core parent.
Fixes: 96d6392b54 ("clk: imx: Add support for i.MX8MN clock driver")
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When doing DRAM frequency change, the DRAM PLL config will
be changed in ATF side, so add 'CLK_GET_RATE_NOCACHE' flag
to make sure each time we get the DRAM PLL frequency through
'clk_get_rate' API, we can get the correct frequency.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Anson Huang <anson.huang@nxp.com>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Per latest imx8mn datasheet of CCM, the parent of usb1_ctrl_root_clk
should be usb_bus.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Check if M4 is enabled to make sure the root
clocks used by M4 are on by default.
Reviewed-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
When we need to support dual linux with jailhouse, there is no clock
controller in 2nd inmate linux cell, it relys on the first linux to
configure the clock ready and on. So we add those clocks required for
the 2nd linux in dts to make them prepare enabled, and pass
clk_ignore_unused to the 1st linux, then the 1st linux will not gated
off the clocks. So the 2nd linux could use IPs without touching clocks.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Remove the earlycon uart clocks that are hard cord in platforms
clock driver, instead of parsing the earlycon uart port from dt
and enable these clocks from clock property in dt node.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
During cpu frequency switching the main "CLK_ARM" is reparented to an
intermediate "step" clock. On imx8mm and imx8mn the 24M oscillator is
used for this purpose but it is extremely slow, increasing wakeup
latencies to the point that i2c transactions can timeout and system
becomes unresponsive.
Fix by switching the "step" clk to SYS_PLL1_800M, matching the behavior
of imx8m cpufreq drivers in imx vendor tree.
This bug was not immediately apparent because upstream arm64 defconfig
uses the "performance" governor by default so no cpufreq transitions
happen.
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Fixes: 96d6392b54 ("clk: imx: Add support for i.MX8MN clock driver")
Cc: stable@vger.kernel.org
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lkml.kernel.org/r/f5d2b9c53f1ed5ccb1dd3c6624f56759d92e1689.1571771777.git.leonard.crestez@nxp.com
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
pll BYPASS bit should be kept inside pll driver for glitchless freq
setting following spec. If exposing the bit, that means pll driver and
clk driver has two paths to touch this bit, which is wrong.
So use EXT_BYPASS bit here.
And drop uneeded set parent, because EXT_BYPASS default is 0.
Suggested-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lkml.kernel.org/r/1568043491-20680-5-git-send-email-peng.fan@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The AUDIO PLL max support 650M, so the original clk settings violate
spec. This patch makes the output 786432000 -> 393216000,
and 722534400 -> 361267200 to aligned with NXP vendor kernel without any
impact on audio functionality and go within 650MHz PLL limit.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MN supports CPU running at 1.5GHz/1.4GHz/1.2GHz, add missing
frequency for ARM PLL table.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add .rate_count assignment which is necessary for searching required
PLL rate from the each PLL table.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To Frac pll, the gate shift is 13, however to Int PLL the gate shift
is 11.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is enabled by default but if it's not explicitly defined and marked
as critical then its parent might get turned off.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
* Replace to audio_pll2_clk with audio_pll2_out
* Replace sys3_pll2_out with sys_pll3_out
* Replace sys1_pll_40m with sys_pll1_40m
* qspi parent[2] is sys_pll2_333m not sys_pll1_800m
Fixes: 96d6392b54 ("clk: imx: Add support for i.MX8MN clock driver")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Call imx_register_uart_clocks() API to keep uart clocks enabled
when earlyprintk or earlycon is active.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang