With stmfx_pinctrl_gpio_init_valid_mask callback, gpio_valid_mask was used
to initialize gpiochip valid_mask for gpiolib. But gpio_valid_mask was not
yet initialized. gpio_valid_mask required gpio-ranges to be registered,
this is the case after gpiochip_add_data call. But init_valid_mask
callback is also called under gpiochip_add_data. gpio_valid_mask
initialization cannot be moved before gpiochip_add_data because
gpio-ranges are not registered.
So, it is not possible to use init_valid_mask callback.
To avoid this issue, get rid of valid_mask and rely on ranges.
Fixes: da9b142ab2 ("pinctrl: stmfx: Use the callback to populate valid_mask")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20191104100908.10880-1-amelie.delaunay@st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
dev_get_platdata(&pdev->dev) returns a pointer on struct stmfx_pinctrl,
not on struct stmfx (platform_set_drvdata(pdev, pctl); in probe).
Pointer on struct stmfx is stored in driver data of pdev parent (in probe:
struct stmfx *stmfx = dev_get_drvdata(pdev->dev.parent);).
Fixes: 1490d9f841 ("pinctrl: Add STMFX GPIO expander Pinctrl/GPIO driver")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20191004122342.22018-1-amelie.delaunay@st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to
the Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver.
-----BEGIN PGP SIGNATURE-----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=2nNz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.4 kernel cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to the
Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver"
* tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (112 commits)
pinctrl: meson-gxbb: Fix wrong pinning definition for uart_c
pinctrl: sh-pfc: Unlock on error in sh_pfc_func_set_mux()
pinctrl: bcm: remove redundant assignment to pointer log
pinctrl: iproc: Add 'get_direction' support
pinctrl: iproc-gpio: Handle interrupts for multiple instances
pinctrl: iproc-gpio: Fix incorrect pinconf configurations
pinctrl: intel: mark intel_pin_to_gpio __maybe_unused
pinctrl: qcom: sdm845: Fix UFS_RESET pin
pinctrl: mvebu: add additional variant for standalone CP115
pinctrl: mvebu: Add CP110 missing pin functionality
dt-bindings: cp110: document the new CP115 pinctrl compatible
pinctrl: bcm2835: Pass irqchip when adding gpiochip
pinctrl: meson: meson: Add of_node_put() before return
pinctrl/gpio: Take MUX usage into account
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150l support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150b support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150 support
pinctrl: amd: disable spurious-firing GPIO IRQs
pinctrl: rza2: Include the appropriate headers
pinctrl: rza2: Drop driver use of consumer flags
...
After we switched the two drivers that have .need_valid_mask
set to use the callback for setting up the .valid_mask,
we can just use the presence of the .init_valid_mask()
callback (or the OF reserved ranges, nota bene) to determine
whether to allocate the mask or not and we can drop the
.need_valid_mask field altogether.
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190819093058.10863-1-linus.walleij@linaro.org
This makes use of the existing callback to populate the
valid mask instead of iteratively setting it up during
probe.
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190819091140.622-1-linus.walleij@linaro.org
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-34-swboyd@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to the following tab (coming from STMFX datasheet), updates
have to done in stmfx_pinconf_set function:
-"type" has to be set when "bias" is configured as "pull-up or pull-down"
-PIN_CONFIG_DRIVE_PUSH_PULL should only be used when gpio is configured as
output. There is so no need to check direction.
DIR | TYPE | PUPD | MFX GPIO configuration
----|------|------|---------------------------------------------------
1 | 1 | 1 | OUTPUT open drain with internal pull-up resistor
----|------|------|---------------------------------------------------
1 | 1 | 0 | OUTPUT open drain with internal pull-down resistor
----|------|------|---------------------------------------------------
1 | 0 | 0/1 | OUTPUT push pull no pull
----|------|------|---------------------------------------------------
0 | 1 | 1 | INPUT with internal pull-up resistor
----|------|------|---------------------------------------------------
0 | 1 | 0 | INPUT with internal pull-down resistor
----|------|------|---------------------------------------------------
0 | 0 | 1 | INPUT floating
----|------|------|---------------------------------------------------
0 | 0 | 0 | analog (GPIO not used, default setting)
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/1564053416-32192-1-git-send-email-amelie.delaunay@st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Set create_link to inform pinctrl core that stmfx wants to create
link with its consumers.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
drivers/pinctrl/pinctrl-stmfx.c:441 stmfx_pinctrl_irq_set_type() warn: bitwise AND condition is false here
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
smatch warnings:
drivers/pinctrl/pinctrl-stmfx.c:225 stmfx_pinconf_get() warn: unsigned 'dir' is never less than zero.
drivers/pinctrl/pinctrl-stmfx.c:228 stmfx_pinconf_get() warn: unsigned 'type' is never less than zero.
drivers/pinctrl/pinctrl-stmfx.c:231 stmfx_pinconf_get() warn: unsigned 'pupd' is never less than zero.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds pinctrl/GPIO driver for STMicroelectronics
Multi-Function eXpander (STMFX) GPIO expander.
STMFX is an I2C slave controller, offering up to 24 GPIOs.
The driver relies on generic pin config interface to configure the GPIOs.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Amelie Delaunay