The header 'linux/moduleparam.h' is included twice in
'sound/isa/sb/emu8000_patch.c'. Once is enough.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These aren't modules, but they do make use of these macros, so
they will need export.h to get that definition. Previously,
they got it via the implicit module.h inclusion.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Lots of sound drivers were getting module.h via the implicit presence
of it in <linux/device.h> but we are going to clean that up. So
fix up those users now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These files were getting access to these two via the implicit
presence of moduleparam.h everywhere. But that is being fixed, so
get these guys what they need in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The implicit presence of module.h lured several users into
incorrectly thinking that they only needed/used modparam.h
but once we clean up the module.h presence, these will show
up as build failures, so fix 'em now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The semantics of snd_mpu401_uart_new()'s interrupt parameters are
somewhat counterintuitive: To prevent the function from allocating its
own interrupt, either the irq number must be invalid, or the irq_flags
parameter must be zero. At the same time, the irq parameter being
invalid specifies that the mpu401 code has to work without an interrupt
allocated by the caller. This implies that, if there is an interrupt
and it is allocated by the caller, the irq parameter must be set to
a valid-looking number which then isn't actually used.
With the removal of IRQF_DISABLED, zero becomes a valid irq_flags value,
which forces us to handle the parameters differently.
This patch introduces a new flag MPU401_INFO_IRQ_HOOK for when the
device interrupt is handled by the caller, and makes the allocation of
the interrupt to depend only on the irq parameter. As suggested by
Takashi, the irq_flags parameter was dropped because, when used, it had
the constant value IRQF_DISABLED.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver doesn't probe the device properly because of left-over cfg[]
that isn't used at all for msnd-classic device. This is only for msnd-
pinnacle.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Its hardware is handled more fully by the new azt1605/azt2316 drivers.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a new driver for Aztech Sound Galaxy ISA soundcards based on the
AZT1605 and AZT2316 chipsets. It's constructed as two seperate drivers
for either chipset generated from the same source file, with (very)
minimal ifdeffery.
The drivers check the SB DSP version to decide if they are being loaded
for the right chip. AZT1605 returns 2.1 by default and AZT2316 3.1.
This isn't full-proof as the DSP version can actually be set through
software but it's close enough -- as far as I've been able to see, the
DSP version can not be stored in the EEPROM and the cards will therefore
startup with the defaults.
This distinction could (with the same success rate) also be used to
decide which chip we're looking at at runtime meaning a single, merged
driver is also an option but I feel it's actually nicer this way. A
merged driver would have to postpone translating the passed in resource
values to the card configuration until it knew which one it was looking
at and would need to postpone erring out on mpu_irq=10 for azt1605 and
mpu_irq=3 for azt2316.
The drivers have been tested on various cards. For snd-azt1605:
FCC-ID I38-MMSN811: Aztech Sound Galaxy Nova 16 Extra
FCC-ID I38-MMSN822: Aztech Sound Galaxy Pro 16 II
and for snd-azt2316:
FCC-ID I38-MMSN824: Aztech Sound Galaxy Pro 16 AB
FCC-ID I38-MMSN826: Trust Sound Expert DeLuxe Wave 32 (05201)
FCC-ID I38-MMSN830: Trust Sound Expert DeLuxe 16+ (05202)
FCC-ID I38-MMSN837: Packard Bell ISA Soundcard 030069
FCC-ID I38-MMSN846: Trust Sound Expert DeLuxe 16-3D (06300)
FCC-ID I38-MMSN847: Trust Sound Expert DeLuxe Wave 32-3D (06301)
FCC-ID I38-MMSN852: Aztech Sound Galaxy Waverider Pro 32-3D
826 and 846 were also marketed directly by Aztech and then known as:
FCC-ID I38-MMSN826: Aztech Sound Galaxy Waverider 32+
FCC-ID I38-MMSN846: Aztech Sound Galaxy Nova 16 Extra II-3D
Together, these cover the AZT1605 and AT2316A, AZT2316R and AZT2316-S
chipsets. All cards work fully -- full-duplex PCM, MIDI and FM. Full
duplex is a little flaky on some.
I38-MSN811 tends to not work in full-duplex but sometimes does with the
highest success rate being achieved when you first start the capture and
then a playback instead of the other way around (it's a CS4231-KL
codec).
The cards with an AD1845XP codec (my I38-MMSN826 and one of my
I38-MMSN830s) are also somewhat duplex-challenged. Sometimes full-duplex
works, sometimes not and this varies from try to try. This seems likely
to be a timing problem somewhere inside wss-lib.
I38-MMSN826 has an additional "ICS2115 WaveFront" wavetable synth
onboard that isn't supported yet. The wavetable synths on I38-MMSN847
and I38-MMSN852 are wired directly to the standard MPU-401 UART and the
AUX1 input on the codec and work without problem.
CD-ROM audio on the cards is routed to the codec "Line" input, Line-In
to its Aux input, and FM/Wavetable to its AUX1 input. I did not rename
the controls due to the capture source enumeration: I see that
capture-source overrides are hardcoded in wss-lib and this is just too
ugly to live.
Versus the old snd-sgalaxy driver these drivers add support for the
models without a configuration EEPROM (which are common), full-duplex,
MPU-401 UART and OPL3. In the future they might grow support for that
ICS2115 WaveFront synth on 826 and an hwdep interface to write to the
EEPROM on the models that have one.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
get_user() may fail, if so return -EFAULT.
[Fixed one missing place by tiwai]
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Smatch complains that if (dev == SNDRV_CARDS) we're one past the end of
the array. That's unlikely to happen in real life, I suppose.
Also smatch complains about "strcpy(card->shortname, pcm->name);"
The "pcm->name" buffer is 80 characters and "card->shortname" is 32
characters. If you follow the call paths it turns out we never actually
use more than 16 characters so it's not a problem. But anyway, let's
make it easy for people auditing this in the future.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ESS ES968 chip is nothing more then a PnP companion
for a non-PnP audio chip. It was paired with non-PnP ESS' chips:
ES688 and ES1688. The ESS' audio chips are handled by the es1688
driver in native mode. The PnP cards are handled by the ES968
driver in SB compatible mode.
Move the ES968 chip handling to the es1688 driver so the driver
can handle both PnP and non-PnP cards. The es968 is removed.
Also, a new PnP id is added for the card I acquired (the change
was tested on this card).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allocate the snd_es1688 during the snd_card allocation.
This allows to remove the card pointer from the snd_es1688 structure.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is only one dma for the ESS ES968 based board.
Its index is 0 and not 1.
This make the es968 card working.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The llseek implementation is identical for existing driver implementations,
so let's merge to the common layer. The same code for the text proc file
can be used even for the binary proc file.
The driver can provide its own llseek method if needed. Then the common
code will be skipped.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check the validity of the file position in the common info layer before
calling read or write callbacks in assumption that entry->size is set up
properly to indicate the max file size.
Removed the redundant checks from the callbacks as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Fix 'else' placement in ifdef block so that build succeeds:
sound/isa/opti9xx/opti92x-ad1848.c:221: error: 'else' without a previous 'if'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While trying to compile jazz16 isa sound driver on alpha (2.6.33+git), I
found a compile failure in jazz16.c (udelay is unknown). Fix it by
including delay.h.
Signed-foo-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Master Control port (MC) is available as the last
PnP resource (OPT005). Use this value instead fo guessing.
Also, add some comments to the code.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The patch "sbawe: fix memory detection" fixed detection
for memoryless SB32 cards but broke detection of memory
above 512KB. This patch fixes the regression.
The patch has been tested on the SB32 card (CT3670) with
0MB, 2MB and 8MB memory installed.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Narrow the dma and irq selection after the DOS driver.
Add ALSA configuration description as well.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is one of Sound Blaster Pro compatible chipsets which is supported
by Linux OSS driver and was missing native supoort for ALSA.
The Jazz16 audio codec is Crystal CS4216 which is capable
of playback and recording up to 48 kHz stereo.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Memory amount is increased before a successful write-read
sequence is done. Thus, 512 kB of onboard memory is detected
on memoryless cards like SB32.
Move the increasing of memory counter after successful read
is done.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use kzalloc rather than kcalloc(1,...)
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert table of pointers to mixer controls into tables
of the mixer controls. It saves about 20% of the snd-sb-common
module size reported by lsmod.
The als4000 uses part of sb16's control table.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sizeof(share_id) is just the size of the pointer. On the other hand,
block->share_id is an array, so its size seems more appropriate.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
expression f;
type T;
@@
*f(...,(T)x,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Overwrite pin config on intel DG45ID board.
intelhdmi - dont power off HDA link
ALSA: hrtimer - Fix lock-up
ALSA: intelhdmi - add channel mapping for typical configurations
ALSA: intelhdmi - channel mapping applies to Pin
ALSA: intelhdmi - accept DisplayPort pin
ALSA: hda - show HBR(High Bit Rate) pin cap in procfs
ALSA: hda - Fix LED GPIO setup for HP laptops with IDT codecs
ASoC: Fix build of OMAP sound drivers
ALSA: opti93x: fix irq releasing if the irq cannot be allocated
Add dB scale for mixer controls. Fix dB scale for
Master Volume control.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move OPTi93x controls definitions to the opti93x driver
from the common wss-lib library module. These controls
are used only by the opti93x driver.
Also, fix capture source names. They are the same as
opl3sa2 names.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The als100 driver is so similar to the dt019x/als007 driver
that one driver's source can be used for both drivers with
only few changes. Merge the dt019x driver into the als100.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the chip->irq to check if the irq should be released so the irq is not released
if it has not been allocated.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PnP data on the OPTI931 and OPTI933 contains io port
range for the MC indirect registers. Use the PnP range
instead of hardwired value 0xE0E.
Also, request region of MC indirect registers so it is
marked as used to other drivers (this was missing previously).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove snd_opti9xx fields which are indirect arguments to
the snd_opti9xx_configure(). Pass these values as function
arguments.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM12 and PCM20 can be set into the ISA PnP mode. The PCM12 PnP
was sold as the PnP device.
Add code to handle detection of these cards using ISA PnP framework.
Tested on the PCM20 in PnP mode. The PCM12 PnP has the same MS Windows
INF file except for a card name displayed for user.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Separate common probing code in order to use it
for PnP probing.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If a hardware is not detected there is a kernel crash
due to not initialized snd_miro->aci pointer. This pointer
is initialized after detection of the opti (miro) chip.
This bug was introduced by patches to expose
ACI mikser outside the snd-miro driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ACI mixer is used to control the radio FM module
installed on the Miro PCM20 sound card. Expose ACI mixer
outside the sound card driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the miro.h header to the include/sound directory. It can
be used in the Miro PCM20 radio driver (v4l).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the snd_card pointer from the snd_miro structure and
do some small code improvements.
Also, move Opti chipset detection before detection of the
ACI mixer, so the mci_base value is set in one place only.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use db scale for all volume controls according to Crystal's datasheets.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the fm_port and mpu_port variables directly in a probe function.
This completely eliminates a need to copy the fm_port value to
the snd_miro structure.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Update control names to be more closer to their meaning.
Change the "Mono" name to the "Beep" as this line is usually
used to forward the PC beeper signal to sound card's output.
Update names for both cs423x and wss.
Clean up cs4235 controls according to the cs4235 doc. Rename
some of the cs4235 controls to be consistent with the cs4236's
ones.
Also, delete one misnamed cs4231 register define.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
1. Set the third argument of the snd_device_new to not NULL, so there is
no warning about bug during chip detection. The third argument is not
used in this driver. It was changed in my previous patch.
2. Remove the fm_port and mpu_port fields from the snd_es18xx structure.
They can be converted to function arguments.
3. Remove the dmaN_size fields from the snd_es18xx structure. These
values are used only in pointer functions and can be easily calculated.
4. Remove the ctrl_lock spinlock which is used only in one read function
which is called once during chip initialization. There are many
writes to the same register and they are not protected on purpose
(see the comment ina the snd_es18xx_config_write()).
5. Use the first part of the text5Sources string table as the text4Soruces
table (they are the same).
6. Merge the same cases for the ES1887 and ES1888 when setting chip's caps.
7. Move the snd_es18xx_reset() to __devinit section.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The cs4236 was two step detection with call to the snd_wss_free()
between two steps. The snd_wss_free() did not free a sound device
created in the snd_wss_create(). This caused an OOPS during module
removal as the same sound device was released twice. The same OOPS
happened if the cs4236 module loading failed.
Fix this by adapting the snd_cs4236_create() to correctly work with
chips less capable then cs4236. The snd_cs4236_create() behaves the
same as the snd_wss_create() if the chip is less capable than the cs4236.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To avoid confusion in control names for the standard analog PC Beep generator
using a small Internal PC Speaker, rename all related "PC Speaker" and "PC
Beep" controls to "Beep" only. This name is more universal and can be also
used on more platforms without confusion.
Introduce also "Internal Speaker" in ControlNames.txt for systems with
full-featured build-in internal speaker.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove intermediate snd_audiodrive structure between
snd_card structure and snd_es18xx. This reduces size of
source code and binary driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The snd_card pointer is redundant and code can be easily
changed to work without it.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The C4231 control set is a superset of the AD1848 control
set so reuse the CS4231 controls definitions for the AD1848.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert CS4231 mixer to dB scale after AD1848 mixer.
Also, add missing microphone boost control for the AD1848
and correct wrong bits for loopback volume on the AD1848.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix coding style errors in the driver.
Also, add missing argument for CMD_XXX_MIDI_VOL command.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Module parameters shouldn't be marked as __devinitdata since they can be
referred via sysfs even after probing.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Old Soundscape cards (pre PnP) work only with AD1848 codecs.
If the CS4231 codec is installed it must be used in AD1848
compatible mode.
Also, add gameport support and remove an unused mpu field.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no sense to limit open MIDI connections with limit
as high as ULONG_MAX.
Also, convert more messages to use the snd_printk.
Correct few old and misleading comments as well.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The conversion solves the problem that firmware size was set to 64KB
while non PnP cards have 128KB firmware files.
An additional firmware initialization code has been moved from the OSS
driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move code from the OSS sscape driver in order to support old Soundscape OEM models.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If spin_lock_irqsave is called twice in a row with the same second
argument, the interrupt state at the point of the second call overwrites
the value saved by the first call. Indeed, the second call does not need
to save the interrupt state, so it is changed to a simple spin_lock.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression lock1,lock2;
expression flags;
@@
*spin_lock_irqsave(lock1,flags)
... when != flags
*spin_lock_irqsave(lock2,flags)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adding MPU-401 support to cmi8330 driver could cause a regression (non-working
sound) on a system where there is no free IRQ for the MPU-401 device (which
is not very uncommon as this card requires two separate IRQs plus a third one
for MPU-401).
When MPU-401 PnP configuration fails (mostly because of unavailable IRQ), just
ignore MPU-401 and continue without it.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
My CMI8329 had OPL3 port specified in SB16 resources. But now I found out that
it was my modification of the card's PnP EEPROM a couple of years ago (can be
done using C9SETROM.EXE utility). I did it because the OPL3 port was
completely missing from PnP data. It seems to be hardwired to 0x388 on
CMI8329.
Find OPL3 port automatically by searching in WSS and SB16 resources. If not
found, assume that it's hardwired to 0x388.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add basic support for CMI8329 cards. Makes PCM and OPL3 work.
Does not break CMI8330 (tested).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In ALSA 1.0.20, the comments were changed to say CMI8330 instead of AD1848.
The CMI8330 chip includes two codecs - AD1848 and SB16, so the comments were
correct and are misleading now. Revert them back.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
3 ISA sound drivers lack their __devexit_p() markers, which would
cause build failures when the kernel is built without hotplug support.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of mangling the CONFIG_* variables in the makefiles over and
over, set a few helper variables in Kconfig.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add module parameter to enable or disable
joystick port (gameport) on the SC6600 and
later cards.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added SNDRV_PCM_INFO_BATCH flag to PCM info field of some drivers that
really don't give the precise pointer value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The last patch to handle newer cards like SC7000
broke initialization of the SC6000. Fix this.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* topic/memdup_user:
ALSA: sound/pci: use memdup_user()
ALSA: sound/usb: use memdup_user()
ALSA: sound/isa: use memdup_user()
ALSA: sound/core: use memdup_user()
Add support for later cards based on CompuMedia ASC-9408 chipsets.
These cards were produced by Gallant.
This patch make the OSS aedsp16 driver redundant.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Always use request_firmware() for loading yss225_registers image.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add ZV port control switch.
This patch is done after solution
given in the ALSA bug #2872 report.
The patch resolves the issue.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the OOPS during a opl3sa2 card suspend
and resume if the driver is loaded but the card
is not found.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Two simple fixes:
1. Use the same pointer for the free_irq() and
the request_irq() calls.
2. A short name of card is appended with '2' or '3'
character depending on a detected chip. Remove
the '2' character from the short name.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since cs4232 and cs4236 drivers are merged, there is no reason to keep
snd-cs4236-lib module separately. Let's merge it into the main driver
as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
cs4232 and cs4236 driver merge to solve PnP BIOS detection.
Also, the patch adds recognition if the chip is cs4236b+
or earlier part. This unifies drivers for both cs4232
and cs4236+ chips. It allows to use the PnP BIOS
detection for the cs4236+ chips. Previously, only
the snd-cs4232 could be detected by the PnP BIOS.
The cs4232+ cards reports two separate PnP BIOS ids.
The patch adds search for the second id to find out
resources assigned to a control port.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The wss_base is disuised parameter for one function.
It is converted to function parameter.
The code_type is only set but never read.
It is removed.
The midi_vol is set only to 0 so it does not work
as detection of change in midi volume. It is fixed.
The xport variable is alias to the port[dev]. Use
the port[dev] directly to increase readability.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The missing module license generates warning
during module loading.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ess1688 driver uses the same port
for PCM audio (SB compatible) and OPL3
synthesis. It is not always right so allow to
choose a different port for OPL3 synthesis.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is driver for Turtle Beach Multisound cards:
Classic, Fiji and Pinnacle.
Tested pcm playback and recording and MIDI playback
on Multisound Pinnacle.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Most cards have OPL3 FM synthetiser but
they do not have OPL3 interrupt wired to
a sound chip or CPU.
Do not create OPL3 timers for such cards
as the timers are useless witthout interrupt.
This patch removes OPL3 timers for following
alsa drivers: snd-ad1816a, snd-opti93x,
snd-opti92x, snd-sc6000, snd-cmi8330.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add OPL3 handling to the driver
and volume control for FM synthesis.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A WSS codec is autocalibrated each time before
playing sound. Do only one calibration during
codec initialization.
Complete snd_wss_calibrate_mute to mute loopback
volume as well.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A comment states that one should wait up to 5 secs
while a waiting loop waits only 5 system ticks.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some drivers in sound/isa/* don't handle the error code properly
from snd_card_create(). This patch fixes these places.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is required to allow the sscape driver
to autodetect installed codec.
Also, do not create a timer if detected codec
has no hardware timer (e.g. AD1848).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Rene Herman
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixed a compile warning below:
sound/isa/sb/sb8.c: In function ‘snd_sb8_probe’:
sound/isa/sb/sb8.c:104: warning: ‘err’ may be used uninitialized in this function
by setting the return value correctly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Removed the direct accesses of dev->bus_id in sound/isa/* by replacement
with dev_err() or dev_warn() functions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Empty files remained likely due to wrong patching.
Remove them now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use the wss_dout function which does not mess
shadowed register values during chip probing.
Otherwise, user ends up with stupid mixer settings
after driver loading.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Replace snd_opl3sa2_info_xxx() with snd_wss_info_xxx().
Drop check of card->private_data which cannot be NULL
if card is not NULL (spotted by Rene Herman).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Mute sound by setting mute bit without
setting volume to 0. It makes both source code
and binary shorter.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Remove card pointer from the snd_opl3sa2
structure and break circular reference
snd_card->snd_opl3sa2->snd_card.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Kill snd_assert() in sound/isa/*, either removed or replaced with
if () with snd_BUG_ON().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Make snd_ad1848_probe() easier to follow. With an exception for only
trying once as soon as the codec is out of init (which should be all
that's needed) the detection logic should be unchanged.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
After the transition from cs4321_lib to wss_lib, azt2320 probe visits
snd_ad1848_probe during detection. It expects register 0 (LEFT_INPUT)
to be able to retain the value 0xaa during detection but AZT2320 does
not support MIC gain meaning it reads back as 0x8a instead.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Remove initializations of spinlock and mutexes which
are done earlier in snd_wss_new(). The snd_wss_new()
is called from snd_wss_create().
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
snd-opti92x-ad1848 mistakingly passes WSS_HW_OPTI93X currently. This
fixes it as tested with a OPTi 82C929A/AD1848 card.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Limit opti93x cards capture formats to only linear ones.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use the wss detection code and kill the ad1848 library.
The library is fully assimilated into the new wss library.
This required reworking of the AD1848 family code
so the code is changed to correctly detect chips from
the AD1848 and CS4231 families.
I have tested it on following cards:
Gallant SC-6600 (codec: AD1848, driver: snd-sc6600)
SoundScape VIVO/90 (codec: AD1845, driver: snd-sscape)
SG Waverider (codec: CS4231A, driver: Rene Herman's snd-galaxy)
Opti930 (codec: built-in - CS4231 compatible, driver: snd-opti93x)
Opti931 (codec: built-in - CS4231 compatible, driver: snd-opti93x)
Gallant SC-70P (chip/codec: CS4237B, driver: snd-cs4236)
Audio Plus 3D (chip/codec: CMI8330A, driver: snd-cmi8330)
Dell Latitude CP (chip/codec: cs4236, driver snd-cs4232)
Sound playback and recording works on all these cards.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use the wss pcm code and kill the ad1848 pcm code.
The AD1848 chip is much slower than CS4231 chips
so the waiting loop was increased 100x (10x is not
enough).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use the wss mixer code and kill the ad1848 mixer code.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use CS4231P instead of AD1848P (kill the AD1848P).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use the wss macros instead of ad1848 ones.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use wss constants for mode.
Move ad1848 hardware constants to the wss.h.
Move mixer tlv macros into the ad1848_lib.c from the ad1848.h.
Drop the MODE_RUNNING spurious IRQ guard on AD1848 as it doesn not seem
to be needed.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The snd_wss is superset of the snd_ad1848 so kill
the latter and replace it with the snd_wss.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Rename functions and structures from the former
cs4321_lib to names more corresponding with the
new name: wss_lib.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Rename file include/sound/cs4231.h
into include/sound/wss.h
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Move the file sound/isa/cs423x/cs4231_lib.c
into sound/isa/cs423x/wss_lib.c
This is the first step toward merging all libraries
for Windows Sound System compatible chips
into a single library.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reviewed-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The acard->wss pointer is uninitialized in this function
which leads to crash during chip PNP detection.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Probing non-existing device causes Oops with snd-opti93x driver
due to NULL access in the destructor of the error path.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Rene Herman <rene.herman@gmail.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Tested-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Ingo Molnar <mingo@elte.hu>
snd_assert() in save_mixer() and restore_mixer() in sb_mixer.c is
just wrong. The debug code wasn't tested at all, obviously...
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch converts the Opti93x driver to use
the cs4231 library instead of duplicating the code.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Tested-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds support for WSS compatible Opti93x
codec to the cs4231-lib.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Tested-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch fixes silenced output from the Opti930.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
After the removal of the sequencer instrument layer SND_GUS_SYNTH was
no longer used.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix a wrong version check that would cause an invalid command to be sent
to SB 1.0 chips.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_opti93x_mixer() is only called by __devinit snd_opti93x_probe(),
so the former can also be __devinit.
snd_miro_mixer() is only called by __devinit snd_miro_probe(),
so the former can also be __devinit.
sound/isa/opti9xx/opti92x-ad1848.c:
WARNING: vmlinux.o(.text+0xf91cd7): Section mismatch: reference to .init.data:snd_opti93x_controls (between 'snd_opti93x_mixer' and 'snd_card_opti9xx_free')
WARNING: vmlinux.o(.text+0xf91d66): Section mismatch: reference to .init.data:snd_miro_controls (between 'snd_opti93x_mixer' and 'snd_card_opti9xx_free')
opti9xx/miro.c:
WARNING: vmlinux.o(.text+0xf926c2): Section mismatch: reference to .init.data:snd_miro_controls (between 'snd_miro_mixer' and 'snd_legacy_find_free_ioport')
WARNING: vmlinux.o(.text+0xf926e5): Section mismatch: reference to .init.data:snd_miro_eq_controls (between 'snd_miro_mixer' and 'snd_legacy_find_free_ioport')
WARNING: vmlinux.o(.text+0xf926f9): Section mismatch: reference to .init.data:snd_miro_line_control (between 'snd_miro_mixer' and 'snd_legacy_find_free_ioport')
WARNING: vmlinux.o(.text+0xf92716): Section mismatch: reference to .init.data:snd_miro_amp_control (between 'snd_miro_mixer' and 'snd_legacy_find_free_ioport')
WARNING: vmlinux.o(.text+0xf9273e): Section mismatch: reference to .init.data:snd_miro_preamp_control (between 'snd_miro_mixer' and 'snd_legacy_find_free_ioport')
WARNING: vmlinux.o(.text+0xf92764): Section mismatch: reference to .init.data:snd_miro_capture_control (between 'snd_miro_mixer' and 'snd_legacy_find_free_ioport')
WARNING: vmlinux.o(.text+0xf92783): Section mismatch: reference to .init.data:snd_miro_radio_control (between 'snd_miro_mixer' and 'snd_legacy_find_free_ioport')
WARNING: vmlinux.o(.text+0xf9279a): Section mismatch: reference to .init.data:snd_miro_eq_controls (between 'snd_miro_mixer' and 'snd_legacy_find_free_ioport')
WARNING: vmlinux.o(.text+0xf927b9): Section mismatch: reference to .init.data:snd_miro_radio_control (between 'snd_miro_mixer' and 'snd_legacy_find_free_ioport')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This busy_wait is not needed after latest changes
to the cs4231-lib
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This header file exists only for some hacks to adapt alsa-driver
tree. It's useless for building in the kernel. Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it. This should be really killed in
future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch enables wavetable chips ES689/ES69X connected to
ESS ES18xx chips. The wavetable chip uses FM DAC if the clock signal
from the wavetable is active.
It has no effect if there is no ESS wavetable chip present.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
sound/isa/sb/sb16_csp.c: In function ‘snd_sb_csp_new’:
sound/isa/sb/sb16_csp.c:121: warning: ‘version’ may be used uninitialized in this function
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This removes the pnp_resource_change use from the ALSA ISAPnP drivers. In
2.4 these were useful in providing an easy path to setting the resources,
but in 2.6 they retain function as a layering violation only.
This makes for a nice cleanup (-550 lines) of ALSA but moreover, ALSA is the
only remaining user of pnp_init_resource_table(), pnp_resource_change() and
pnp_manual_config_dev() (and, in fact, of 'struct pnp_resource_table') in
the tree outide of drivers/pnp itself meaning it makes for more cleanup
potential inside the PnP layer.
Thomas Renninger acked their removal from that side, you did from the ALSA
side (CC list just copied from that thread).
Against current alsa-kernel HG. Many more potential cleanups in there, but
this _only_ removes the pnp_resource_change code. Compile tested against
current alsa-kernel HG and compile- and use-tested against 2.6.23.x (few
offsets).
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Check the value ranges in ctl put callbacks properly (in the rest drivers).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Remove sequencer instrument layer from the tree.
This mechanism hasn't been used much with the actual devices. The only
reasonable user was OPL3 loader, and now it was rewritten to use hwdep
instead. So, let's remove the rest of rotten codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fixed the print format for debug message.
Spotted by Matthew Wilcox.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
The last patches to replace with schedule_timeout() don't work as expected.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
the BTC 1817DW board.
The QS1000 is connected through the digital input
to the Opti931 chip.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
open and close operations are called only from pcm layer
and mutexed there with pcm->open_mutex.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The polling loop to check for ACI to go down was more convoluted than it
needed to be. New loop should be more efficient and it is a lot simpler. The
old loop checked for a timeout before checking for ACI down, which could
result in an erroneous timeout. It's only a failure if the timeout expires
_and_ ACI is still high. There is nothing wrong with the timeout expiring
while the task is sleeping if ACI went low.
A polling loop to check for the device to leaving INIT mode is removed. The
device must have already left init for the previous ACI loop to have finished.
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix schedule_timeout() use in alsa-kernel. Mostly just
schedule_timeout(1) --> schedule_timeout_uninterruptible(1)
The wavefront_synth one fixes the surrounding loop as well. In ymfpci_main,
delete a superfluous set_current_state() and in soc/soc-dapm.c replace an
_interruptible with _uninterruptible in some debug code; it's not waiting
for signals.
Signed-off-by: Rene Herman <rene.herman>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds support for audio part of the Ensoniq
SoundScape VIVO cards. The MIDI part is not supported.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The OPTi ISA-PnP chips advertise their OPL4 base at 0x380 (to 0x3f0) through
pnp and put their on-chip OPL3 at +8. The driver assumes the provided
value is the ALBase (OPL3 address) though and checks for an OPL4 at -8,
which means that simply adding 8 to the pnp provides value works to fix
detection of both OPL3 and OPL4.
Problem spotted on 931 and 933 by Krzysztof Helt and confirmed on 924 and
925 (together all OPTi ISA-PnP chips) by me.
Signed-off-by; Rene Herman <rene.herman@gmail.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds second DMA channel and WSS port settings
to the sscape driver. Also, it adds internal card type setting.
The Ensoniq SoundScape VIVO PnP id is added but not handled
yet.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch zeroes buffer for the card name and
fixes incorrect jump in the probe function.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch fixes ad1848_lib waiting loops to be the same as in the cs4231_lib.
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
sound/isa/sc6000.c: In function 'sc6000_dsp_reset':
sound/isa/sc6000.c:270: error: implicit declaration of function 'udelay' sound/isa/sc6000.c: In function 'sc6000_init_mss':
sound/isa/sc6000.c:327: error: implicit declaration of function 'msleep'
{standard input}: Assembler messages:
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This is port of the Gallant SC-6000 driver from the OSS aedsp16 driver.
This card was also sold as AudioExcel DSP 16 and Zoltrix AV302 (Audio
Plus True 16).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch replaces long msleeps in waiting loops
with schedule_timeout() calls.
Signed-off-by: Krzysztof Helt <krzysztof.h1 at wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
While I'm at it another 'while I'm there' -- replace commented out debug
code with snd-printd{,d}.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
If I'm not mistaken, any (new) use of HZ these days is considered a bug so
while I'm there...
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
When the ad1848/cs2431 is first being initialized, auto-calibration may not
be set causing a timeout waiting for it in snd_ad1848/cs4231_mce_down().
This has no dire consequences other than an alarming printk, but since what
we need to wait for is for the calibration to _finish_, let's just check for
that instead.
The early chips need a slight delay (as commented -- 5 sample periods) to be
sure that _if_ calibration is going to happen, it has started when we check
While the CS4231A datasheet implies it'll happen immediately on downing MCE,
some testing is showing that there's a window there as well, so just do the
delay everywhere.
Thanks to Krysztof Helt for pinpointing this problem.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch replaces a common delay loop by a function.
It also uses ARRAY_SIZE macro for the rates table.
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch replaces a common delay loop by a function.
It also uses ARRAY_SIZE macro for the rates table.
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
CS5530 is a PCI device and often shares the IRQ although the SB common
routine tries to allocate it exclusively. This patch allows shared IRQ
for CS5530.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Use the standard firmware loader for loading ICS2115 OS firmware file.
This is the last old bad guy that is still using sys_open() and sys_read()
calls, and now all should be gone.
The patch also adds the missing description of module options related
with wavefront_synth.c.
Due to this rewrite, user will have to copy or make symlink the firmware
file appropriately to the standard firmware path such as /lib/firmware.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Set the SNDRV_PCM_INFO_SYNC_START flag and the substream's sync ID
(only) if the substream actually can be linked to another one.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch uses the Kconfig parameters SND_AD1848_LIB and
SND_CS4231_LIB instead of mentioning each driver that requires
the ad1848-lib or cs4231-lib separately in the Makefiles.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
As reported by Troy Heidner, the 'Gateway Solo 5150' laptop (for one) has an
onboard ESS1879 that identifies itself through PNPBIOS as just that. He also
confirmed that other than not knowing about it, snd-es18xx drives the chip
fine, so this adds the ID to the driver.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The mode change / recalibration doesn't work always with opl3sa2 devices,
e.g. the first time it's played back. The patch fixes the problem.
Signed-off-by: Paul Vojta <vojta@math.berkeley.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Clean up codes using the new common snd_ctl_boolean_*_info() callbacks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch fixes the following compile error with
CONFIG_SND_CS5530=y, CONFIG_ISA=n:
<-- snip -->
...
LD .tmp_vmlinux1
sound/built-in.o: In function 'snd_sb16_capture_trigger':
sb16_main.c:(.text+0x212ad): undefined reference to 'snd_sbdsp_command'
sb16_main.c:(.text+0x212cc): undefined reference to 'snd_sbdsp_command'
sb16_main.c:(.text+0x212f7): undefined reference to 'snd_sbdsp_command'
sound/built-in.o: In function 'snd_sb16_playback_trigger':
sb16_main.c:(.text+0x2136d): undefined reference to 'snd_sbdsp_command'
sb16_main.c:(.text+0x2138c): undefined reference to 'snd_sbdsp_command'
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Add Neomagic MagicWave 3D to list of supported devices for opl3sa2
driver.
Signed-off-by: Paul Vojta <vojta@math.berkeley.edu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fixed the invalid use of schedule_timeout_interruptible() without
checking pending signals. Simply replaced with schedule_timeout().
Suggestions thanks to Jeff Garzik.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
A few PCI drivers like ALS4000 and CS5530 require the SB16-codes.
This patch fixes / improves the dependency between SB modules and
PCI drivers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Add support for Cyrix/NatSemi Geode SC5530 (VSA1).
The driver is snd-cs5530.
Signed-off-by Ash Willis <ashwillis@programmer.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
- Added the missing pnp_unregister_card_driver() in the case ISA PnP
isn't found, which caused an error at kobject_add with -EEXIST
Jun 11 09:07:31 rain kernel: kobject_add failed for opti9xx with -EEXIST, don't try to register things with the same name in the same directory.
Jun 11 09:07:31 rain kernel: [<c01c18fa>] kobject_shadow_add+0x12a/0x1c0
Jun 11 09:07:31 rain kernel: [<c01c1a81>] kobject_register+0x21/0x50
Jun 11 09:07:31 rain kernel: [<c01f09a2>] bus_add_driver+0x72/0x1b0
Jun 11 09:07:31 rain kernel: [<c01d3dff>] pnp_register_card_driver+0x4f/0xc0
Jun 11 09:07:31 rain kernel: [<c89bc00a>] alsa_card_opti9xx_init+0xa/0x25 [snd_opti92x_ad1848]
Jun 11 09:07:31 rain kernel: [<c0136947>] sys_init_module+0x157/0x1610
Jun 11 09:07:31 rain kernel: [<c01029b4>] syscall_call+0x7/0xb
- Fixed the probe behavior when no PnP is set up. Now it behaves
like the former version.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
isa_register_driver() returns an error if no device is found
and it's no fatal error for the drivers with pnp support.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
From: David Rientjes <rientjes@google.com>
isapnp[] is only used for CONFIG_PNP. If this configuration option is
not set, do not declare the array.
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Since request_firmware() is no longer used when the internal firmware
images are used, it is no longer necessary to depend on FW_LOADER in
this case.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Don't use request_firmware() if the internal firmwares are defined
via Kconfig. Otherwise it results in a significant delay at loading
time (minutes).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The ad1816a driver fails if the mpu401 driver has been loaded first. This
patch against linux 2.6.20 fixes it by just ignoring the MPU-401 device in
that case, so that the rest of the sound card can be used. The ad1816a
driver already handles the MPU-401 device being unavailable due to lack of
resources in the same way.
Signed-off-by: Rask Ingemann Lambertsen <rask@sygehus.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The external firmware files are not in the alsa-plugins but in the
alsa-firmware package.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Move the FW_LOADER dependencies out of the *_FIRMWARE_IN_KERNEL entries
because these drivers use the firmware loader regardless of whether
there is an in-kernel firmware image.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Some drivers are already ifdefs for enabling external firmwares
but not defined in Kconfig. Now they appear as the kernel configs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added a new macro snd_pcm_group_for_each_entry() just for code cleanup.
Old macros, snd_pcm_group_for_each() and snd_pcm_group_substream_entry(),
are removed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Port the rest of ALSA ISA drivers to use isa_driver framework
instead of platform_driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The gusextreme driver neglects to set the gus->codec_flag meaning
snd_gf1_pcm_new() allocates a second 'PCM Playback Volume' control,
which makes the driver fail to load.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
gusextreme: port to isa_bus infrastructure
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
gusclassic: port to isa_bus infrastructure
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Seperate out the legacy probing into its own function, improving
readability.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
es1688: port to isa_bus infrastructure. very slight reorganization of
the auto-probe code to be a bit easier on the eye (if not the senses).
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
cs4231: port to isa_bus infrastructure.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
adlib: port to isa_bus infrastructure.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
ad1848: port to isa_bus infrastructure
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix __devinit and __devexit issues with sound drivers.
Resolves MODPOST warnings similar to:
WARNING: sound/drivers/snd-dummy.o - Section mismatch: reference to .init.text:snd_dummy_probe from .data.rel.local between 'snd_dummy_driver' (at offset 0x0) and 'snd_dummy_controls'
WARNING: sound/drivers/snd-mtpav.o - Section mismatch: reference to .init.text:snd_mtpav_probe from .data.rel.local between 'snd_mtpav_driver' (at offset 0x0) and 'snd_mtpav_input'
WARNING: sound/drivers/snd-virmidi.o - Section mismatch: reference to .init.text:snd_virmidi_probe from .data.rel.local after 'snd_virmidi_driver' (at offset 0x0)
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Mark TLV data as 'const'
Signed-of-by: Philipp Matthias Hahn <pmhahn@pmhahn.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Load the YSS225 register initialization data using request_firmware(),
if possible, instead of using the built-in data blob.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Instead of using a somewhat algorithmic approach of initializing the
YSS225's registers, just use a simple series of port/value pairs.
This makes it easier to later replace or entirely remove the register
data blob.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Jesper Juhl