We can simplify the code by caching the CPU DAI master/slave
information rather than reading previously set register bit.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch sets missing stream_name of capture part of the DAI driver
so we can define DAPM routing properly also for the capture stream.
While at it "Playback" suffix is added to the playback stream names
to clearly identify playback/capture.
Together with related dts patch this fixes NULL pointer dereference
when opening ALSA device for recording on Odroid XU3.
Fixes: 64aba9bca5 ("ASoC: samsung: i2s: Add widgets and routes for DPCM support")
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On some SoCs (e.g. Exynos5433) there are multiple "IIS multi audio
interfaces" and the driver will try to register there multiple times
same platform device for the secondary FIFO, which of course fails
miserably. To fix this we derive the secondary platform device name
from the primary device name. The secondary device name will now
be <primary_dev_name>-sec instead of fixed "samsung-i2s-sec".
The fixed platform_device_id table entry is removed as the secondary
device name is now dynamic and device/driver matching is done through
driver_override.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes unregistration of the secondary platform device so all
resources are properly released. Additionally the removal sequence
is corrected so it is in reverse order comparing to probe sequence.
The test against NULL priv->pdev_sec is removed as it is not necessary.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When np is NULL i2s_pdata could also be NULL but i2s_pdata is now being
dereferenced without proper check. Fix this and shorten the error message
so we don't exceed 80 characters limit.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Spelling error fixes, upper/lower case letter changes.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change indentation so this macro definition spans 2 rows and looks
more consistent with surrounding code.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the probe call is on the primary DAI we can use 'other' in place of
i2s->sec_dai, if the probe call is on the secondary DAI we can use 'i2s'
in place of other->sec_dai.
While at it fix one whitespace issue.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a part of conversion of Samsung platforms to use the custom DMA
config for specifying DMA channel names, in addition to passing custom
DMA device for the secondary CPU DAI's "PCM" component for some variants
of the I2S controller.
We also don't set the SND_DMAENGINE_PCM_FLAG_CUSTOM_CHANNEL_NAME any more
as setting it wouldn't allow to specify DMA channels through the custom
DMA config.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch makes the spinlock serializing access to the primary/secondary
PCM a per I2S controller lock, rather than a global one. There is no need
to have a global lock across multiple I2S controllers in the SoC.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The quirk flags are common for the primary and the secondary DAI
so move respective field from struct i2s_dai to common driver data
structure.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The IP variant data is another thing common for both DAIs, move it
to the driver's common data structure.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As we now have the 'priv' pointer in most of the places we can use
priv->lock directly, dropping extra indirection in the SFR region
spinlock access.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SFR region is common for both DAIs so move related data structure
field from struct i2s_dai to the common driver data structure.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to keep the PM suspend/resume register cache separate
for each DAI as those registers are common, move related i2s_dai data
structure to the driver's common data structure. This will allow us
to simplify the code a little eventually and to make it easier to follow.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The clock for generating I2S signals is also common for both CPU DAIs
so move it to the driver's common data structure.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The core clock is also common for both CPU DAIs so move it to
the driver's private data structure.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds DAPM widgets required to model the internal mixer
of the I2S controller merging audio streams from the primary and
from the secondary PCM interface.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Having the clocks provider data in struct samsung_i2s_priv, i.e. per the I2S
controller instance, rather than per CPU DAI better models the hardware and
simplifies the code a little. The clock provider is common for both DAIs.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch introduces again registration of additional platform device as
we still need it for registering the secondary dmaengine PCM component.
This patch in most part is a revert of changes done in commit
be2c92eb64 ("ASoC: samsung: i2s: Remove virtual device for secondary DAI")
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch includes minimal changes as a prerequisite for adding support
for the Exynos secondary I2S interface as second DAI of the I2S component.
Doing it that way allows to avoid problems as indicated in commmit
6b01e0365b1689 ("ASoC: samsung: i2s: disable secondary DAI until it gets fixed")
The samsung_i2s_get_pri_dai() helper added in this patch is temporary and
will be removed in one of subsequent patches.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The additional function argument will allow to select proper DMA device
for requesting DMA channel for the secondary CPU DAI.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure i2s->rclk_srcrate is properly initialized also during
playback through the secondary DAI.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1381093 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As the RCLK clock may be updated through the common clk API before each
snd_soc_dai_ops::trigger call, it is not enough to update i2s->rclk_srcrate
only once after it has been initially set to 0. To avoid wrong PSR values
we always get RCLK frequency from the CLK_I2S_RCLK_SRC clock, when that
clock is available.
Fixes: e1417fdf3011 "ASoC: samsung: i2s: Ensure the RCLK rate is properly determined"
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SAMSUNG_I2S_OPCLK is not currently used by any card driver thus we can
safely change semantics of 'dir' argument of the I2S set_sysclk() callback.
Now an enumeration is exported instead of directly using register bit field
values.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It seems both PCLK_I2S1 and SCLK_I2S1 clocks need to be enabled before
I2S1 control registers can be accessed on exynos5433. If SCLK clock
is disabled an exception is triggered. To fix this parent clock of
the RCLK_SRC clock is assigned to pri_dai->op_clk so required gate
clock is handled by the runtime PM ops.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to support multiple instances of the I2S IP block the platform
device name is prepended to each clock registered by the driver.
The clock-output-names property is now not used, this should not cause
any issues as, for example, CDCLK clock is referenced through DT 'clocks'
property, not by name.
This change allows to have both I2S0 and I2S1 enabled simultaneously
on exynos5433 and working properly when #clock-cells property is specified
in respective DT nodes.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the RCLK mux clock configuration is specified in DT and no set_sysclk()
callback is used in the sound card driver the sclk_srcrate field will remain
set to 0, leading to an incorrect PSR divider setting.
To fix this the frequency value is retrieved from the CLK_I2S_RCLK_SRC clock,
so the actual RCLK mux selection is taken into account.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Secondary DAI in Exynos I2S driver is not used by any of the currently
supported boards and it causes problems due to some limitations in the
ASoC code. Disable it until it gets proper support both by board-specific
and ASoC core code. Also disable IDMA support, which relies on secondary
DAI presence.
This patch fixes following kernel warning:
samsung-i2s 3830000.i2s: ASoC: Failed to create component debugfs directory
samsung-i2s 3830000.i2s: ASoC: Failed to create component debugfs directory
------------[ cut here ]------------
WARNING: CPU: 3 PID: 82 at fs/proc/generic.c:330 proc_register+0xec/0x10c
proc_dir_entry 'sub0/prealloc' already registered
Modules linked in:
CPU: 3 PID: 82 Comm: kworker/3:1 Not tainted 4.14.0-rc5-next-20171017 #3089
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events deferred_probe_work_func
[<c0110114>] (unwind_backtrace) from [<c010c900>] (show_stack+0x10/0x14)
[<c010c900>] (show_stack) from [<c083e664>] (dump_stack+0x90/0xc8)
[<c083e664>] (dump_stack) from [<c011d2b8>] (__warn+0xd4/0x100)
[<c011d2b8>] (__warn) from [<c011d384>] (warn_slowpath_fmt+0x38/0x48)
[<c011d384>] (warn_slowpath_fmt) from [<c0271268>] (proc_register+0xec/0x10c)
[<c0271268>] (proc_register) from [<c027130c>] (proc_create_data+0x84/0xc8)
[<c027130c>] (proc_create_data) from [<c061afbc>] (snd_info_register+0x64/0xcc)
[<c061afbc>] (snd_info_register) from [<c062a6e0>] (snd_pcm_lib_preallocate_pages1+0x78/0x1a0)
[<c062a6e0>] (snd_pcm_lib_preallocate_pages1) from [<c063eef4>] (dmaengine_pcm_new+0xa0/0x1ec)
[<c063eef4>] (dmaengine_pcm_new) from [<c062b9f8>] (snd_soc_platform_drv_pcm_new+0x1c/0x28)
[<c062b9f8>] (snd_soc_platform_drv_pcm_new) from [<c063d54c>] (soc_new_pcm+0x2f4/0x4f4)
[<c063d54c>] (soc_new_pcm) from [<c063107c>] (snd_soc_register_card+0xc4c/0xdc4)
[<c063107c>] (snd_soc_register_card) from [<c063db30>] (devm_snd_soc_register_card+0x34/0x70)
[<c063db30>] (devm_snd_soc_register_card) from [<c064af60>] (asoc_simple_card_probe+0x230/0x47c)
[<c064af60>] (asoc_simple_card_probe) from [<c047f8fc>] (platform_drv_probe+0x50/0xb0)
[<c047f8fc>] (platform_drv_probe) from [<c047dee0>] (driver_probe_device+0x2a0/0x46c)
[<c047dee0>] (driver_probe_device) from [<c047c0bc>] (bus_for_each_drv+0x44/0x8c)
[<c047c0bc>] (bus_for_each_drv) from [<c047db50>] (__device_attach+0xa0/0x134)
[<c047db50>] (__device_attach) from [<c047cf7c>] (bus_probe_device+0x88/0x90)
[<c047cf7c>] (bus_probe_device) from [<c047d484>] (deferred_probe_work_func+0x3c/0x168)
[<c047d484>] (deferred_probe_work_func) from [<c01371f8>] (process_one_work+0x188/0x41c)
[<c01371f8>] (process_one_work) from [<c01374b4>] (process_scheduled_works+0x28/0x38)
[<c01374b4>] (process_scheduled_works) from [<c01376d4>] (worker_thread+0x210/0x4dc)
[<c01376d4>] (worker_thread) from [<c013d9cc>] (kthread+0x128/0x164)
[<c013d9cc>] (kthread) from [<c0108848>] (ret_from_fork+0x14/0x2c)
---[ end trace bad8db6ee771d094 ]--
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add specific dais name when components are registered. Component and dai
name will follow their parent dev name, if the name isn't described. In
case of this driver, each dais will have same name like '11440000.i2s0' by
fmt_single_name function.
The problem having same name is that TM2 machine driver can't detect
capture devices correctly. Machine driver doesn't know which one is proper
to use for cpu dai. The driver just selects to use 'samsung-i2c-sec' that
doesn't have capture functionality because the component of
samsung-i2s-sec is located in the first of the component_list.
I add dai name like 'samsung-i2s', 'samsung-i2s-sec' for each dais. The
reason why adding dai id to 1 is that it doesn't allow to use particular
dai name in case of when I use 0 for dai id.
Signed-off-by: Jaechul Lee <jcsing.lee@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If 'clk_prepare_enable()' fails, we must 'put' the corresponding clock.
Othewise, there is a resource leak.
Fixes: f5c97c7b04 ("ASoC: samsung: i2s: Handle return value of clk_prepare_enable.")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
If (quirks & QUIRK_SEC_DAI == 0) then samsung_i2s_probe() doesn't allocate
sec_dai and pri_dai->sec_dai remains Null, but samsung_i2s_remove()
performs pri_dai->sec_dai dereference in any case.
The patch removes useless reinitialization of sec_dai at
samsung_i2s_remove(), because resources are under devm control.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver can support more frequencies over 96KHz. There are no reasons
to limit the frequency range below 96KHz. If codecs/amps or something else
can't support higher resolution rates, the constraints would be set rates
properly because each drivers have its own limits.
I added the 'pcm_rates' field to the dai_data to be set rates by the
compatibilities. As a result, rates will be set each devices respectively.
For example of exynos5433, rates will be set from 8KHz to 192KHz.
Signed-off-by: Jaechul Lee <jcsing.lee@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit cdaf9af1ea
which breaks I2S support on the non-DT Samsung SoC platforms,
since the default "tx", "rx" DMA channel names for playback
and capture streams or custom channel names in struct
snd_dmaengine_pcm_config are supported in the ASoC dmaengine
module only for devicetree booting case.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds pointer to I2S device to clk_register_* functions.
This in the future allow clock framework to ensure proper runtime state
of the I2S device during all operations on the clocks provided by I2S
module.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds handling of parent operational clock to runtime PM
callbacks. This way it is ensured that when I2S module is in runtime
suspended state, all its parent clocks are disabled and unprepared.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch moves saving and restoring I2S registers to runtime PM
operations, what prepares the driver to operate with audio power domain.
When support for audio power domain is enabled and the domain is being
turned off, the I2S module will loose its context (registers), so runtime
callbacks have to handle it. System sleep suspend/resume operation are
implemented on top of runtime PM operations with generic
pm_runtime_force_suspend/resume helpers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds calls to pm_runtime_get/put to ensure that any access to
I2S registers is done with proper (active) runtime PM state of I2S device.
Till now the driver enabled runtime PM, but didn't manage the state during
driver operation. The driver worked fine only because the runtime PM
callbacks managed device clock, which was enabled all the time because of
the additional enable call in the driver's probe function.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For some unknown (maybe historical?) reasons support for secondary I2S DAI
was implemented by adding additional virtual platform device, which was
then probed again with the main I2S driver. This pattern is really hard
to follow and provides no benefits, so lets remove this hack and register
both DAIs during linear probe of Exynos I2S controller driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver was checking for non-NULL address of struct's members:
- s3c_audio_pdata->type (union),
- s3c_audio_pdata->type.i2s (embedded struct).
This is pointless as these will be always non-NULL. The 's3c_audio_pdata'
is always initialized in static memory so it will be zeroed.
Additionally the 'type' member was an union with only one member.
It is safe to reorganize the structures to get rid of useless union and
checks for addresses to fix the coccinelle warning:
>> sound/soc/samsung/i2s.c:1270:2-4: ERROR: test of a variable/field address
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC Samsung sub-drivers tried to get access to their DMA engine
controllers as a last step in driver probe. If a DMA engine was not
available yet, samsung_asoc_dma_platform_register() function ended in
-EPROBE_DEFER, but the driver already registered its component to ASoC
core. This patch moves samsung_asoc_dma_platform_register() call before
registering any components, to the common place, where driver was gathering
all needed resources.
In case of Samsung Exynos i2s driver the issue was even worse. The driver
managed already to register its secondary DAI platform device before
even getting the DMA engine access. That together with -EPROBE_DEFER error
code from samsung_i2s_probe() immediately triggered another round of
deferred probe retry and in turn endless loop of driver probing.
This patch fixes broken boot on Odroid XU3 and other Exynos5422-based
boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sylwester Nawrocki