It is useful be able to configure port policers on a switch to accept
frames of various sizes:
- Increase the MTU for better throughput from the default of 1500 if it
is known that there is no 10/100 Mbps device in the network.
- Decrease the MTU to limit the latency of high-priority frames under
congestion, or work around various network segments that add extra
headers to packets which can't be fragmented.
For DSA slave ports, this is mostly a pass-through callback, called
through the regular ndo ops and at probe time (to ensure consistency
across all supported switches).
The CPU port is called with an MTU equal to the largest configured MTU
of the slave ports. The assumption is that the user might want to
sustain a bidirectional conversation with a partner over any switch
port.
The DSA master is configured the same as the CPU port, plus the tagger
overhead. Since the MTU is by definition L2 payload (sans Ethernet
header), it is up to each individual driver to figure out if it needs to
do anything special for its frame tags on the CPU port (it shouldn't
except in special cases). So the MTU does not contain the tagger
overhead on the CPU port.
However the MTU of the DSA master, minus the tagger overhead, is used as
a proxy for the MTU of the CPU port, which does not have a net device.
This is to avoid uselessly calling the .change_mtu function on the CPU
port when nothing should change.
So it is safe to assume that the DSA master and the CPU port MTUs are
apart by exactly the tagger's overhead in bytes.
Some changes were made around dsa_master_set_mtu(), function which was
now removed, for 2 reasons:
- dev_set_mtu() already calls dev_validate_mtu(), so it's redundant to
do the same thing in DSA
- __dev_set_mtu() returns 0 if ops->ndo_change_mtu is an absent method
That is to say, there's no need for this function in DSA, we can safely
call dev_set_mtu() directly, take the rtnl lock when necessary, and just
propagate whatever errors get reported (since the user probably wants to
be informed).
Some inspiration (mainly in the MTU DSA notifier) was taken from a
vaguely similar patch from Murali and Florian, who are credited as
co-developers down below.
Co-developed-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Co-developed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping header include additions in macsec.c
A bug fix in 'net' overlapping with the removal of 'version'
string in ena_netdev.c
Overlapping test additions in selftests Makefile
Overlapping PCI ID table adjustments in iwlwifi driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Not only did this wheel did not need reinventing, but there is also
an issue with it: It doesn't remove the VLAN header in a way that
preserves the L2 payload checksum when that is being provided by the DSA
master hw. It should recalculate checksum both for the push, before
removing the header, and for the pull afterwards. But the current
implementation is quite dizzying, with pulls followed immediately
afterwards by pushes, the memmove is done before the push, etc. This
makes a DSA master with RX checksumming offload to print stack traces
with the infamous 'hw csum failure' message.
So remove the dsa_8021q_remove_header function and replace it with
something that actually works with inet checksumming.
Fixes: d461933638 ("net: dsa: tag_8021q: Create helper function for removing VLAN header")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a flow_dissect callback which returns the network offset and
where to find the skb protocol, given the tags structure a common
function works for both tagging formats that are supported.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When both the switch and the bridge are learning about new addresses,
switch ports attached to the bridge would see duplicate ARP frames
because both entities would attempt to send them.
Fixes: 5037d532b8 ("net: dsa: add Broadcom tag RX/TX handler")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flow_action_hw_stats_types_check() helper takes one of the
FLOW_ACTION_HW_STATS_*_BIT values as input. If we align
the arguments to the opening bracket of the helper there
is no way to call this helper and stay under 80 characters.
Remove the "types" part from the new flow_action helpers
and enum values.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue a warning to the kernel log if phylink_mac_link_state() returns
an error. This should not occur, but let's make it visible.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, DSA drivers should configure CPU and DSA ports to their
maximum speed. In many configurations this is sufficient to make the
link work.
In some cases it is necessary to configure the link to run slower,
e.g. because of limitations of the SoC it is connected to. Or back to
back PHYs are used and the PHY needs to be driven in order to
establish link. In this case, phylink is used.
Only instantiate phylink if it is required. If there is no PHY, or no
fixed link properties, phylink can upset a link which works in the
default configuration.
Fixes: 0e27921816 ("net: dsa: Use PHYLINK for the CPU/DSA ports")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce flow_action_basic_hw_stats_types_check() helper and use it
in drivers. That sanitizes the drivers which do not have support
for action HW stats types.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ocelot has the concept of a CPU port. The CPU port is represented in the
forwarding and the queueing system, but it is not a physical device. The
CPU port can either be accessed via register-based injection/extraction
(which is the case of Ocelot), via Frame-DMA (similar to the first one),
or "connected" to a physical Ethernet port (called NPI in the datasheet)
which is the case of the Felix DSA switch.
In Ocelot the CPU port is at index 11.
In Felix the CPU port is at index 6.
The CPU bit is treated special in the forwarding, as it is never cleared
from the forwarding port mask (once added to it). Other than that, it is
treated the same as a normal front port.
Both Felix and Ocelot should use the CPU port in the same way. This
means that Felix should not use the NPI port directly when forwarding to
the CPU, but instead use the CPU port.
This patch is fixing this such that Felix will use port 6 as its CPU
port, and just use the NPI port to carry the traffic.
Therefore, eliminate the "ocelot->cpu" variable which was holding the
index of the NPI port for Felix, and the index of the CPU port module
for Ocelot, so the variable was actually configuring different things
for different drivers and causing at least part of the confusion.
Also remove the "ocelot->num_cpu_ports" variable, which is the result of
another confusion. The 2 CPU ports mentioned in the datasheet are
because there are two frame extraction channels (register based or DMA
based). This is of no relevance to the driver at the moment, and
invisible to the analyzer module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Suggested-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the immense variety of classification keys and actions available
for tc-flower, as well as due to potentially very different DSA switch
capabilities, it doesn't make a lot of sense for the DSA mid layer to
even attempt to interpret these. So just pass them on to the underlying
switch driver.
DSA implements just the standard boilerplate for binding and unbinding
flow blocks to ports, since nobody wants to deal with that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Place phylink_start()/phylink_stop() inside dsa_port_enable() and
dsa_port_disable(), which ensures that we call phylink_stop() before
tearing down phylink - which is a documented requirement. Failure
to do so can cause use-after-free bugs.
Fixes: 0e27921816 ("net: dsa: Use PHYLINK for the CPU/DSA ports")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate the resolved link configuration down via DSA's
phylink_mac_link_up() operation to allow split PCS/MAC to work.
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate the resolved link parameters via the mac_link_up() call for
MACs that do not automatically track their PCS state. We propagate the
link parameters via function arguments so that inappropriate members
of struct phylink_link_state can't be accessed, and creating a new
structure just for this adds needless complexity to the API.
Tested-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Passing tag size to skb_cow_head will make sure
there is enough headroom for the tag data.
This change does not introduce any overhead in case there
is already available headroom for tag.
Signed-off-by: Per Forlin <perfn@axis.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Passing tag size to skb_cow_head will make sure
there is enough headroom for the tag data.
This change does not introduce any overhead in case there
is already available headroom for tag.
Signed-off-by: Per Forlin <perfn@axis.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA sets up a switch tree little by little. Every switch of the N
members of the tree calls dsa_register_switch, and (N - 1) will just
touch the dst->ports list with their ports and quickly exit. Only the
last switch that calls dsa_register_switch will find all DSA links
complete in dsa_tree_setup_routing_table, and not return zero as a
result but instead go ahead and set up the entire DSA switch tree
(practically on behalf of the other switches too).
The trouble is that the (N - 1) switches don't clean up after themselves
after they get an error such as EPROBE_DEFER. Their footprint left in
dst->ports by dsa_switch_touch_ports is still there. And switch N, the
one responsible with actually setting up the tree, is going to work with
those stale dp, dp->ds and dp->ds->dev pointers. In particular ds and
ds->dev might get freed by the device driver.
Be there a 2-switch tree and the following calling order:
- Switch 1 calls dsa_register_switch
- Calls dsa_switch_touch_ports, populates dst->ports
- Calls dsa_port_parse_cpu, gets -EPROBE_DEFER, exits.
- Switch 2 calls dsa_register_switch
- Calls dsa_switch_touch_ports, populates dst->ports
- Probe doesn't get deferred, so it goes ahead.
- Calls dsa_tree_setup_routing_table, which returns "complete == true"
due to Switch 1 having called dsa_switch_touch_ports before.
- Because the DSA links are complete, it calls dsa_tree_setup_switches
now.
- dsa_tree_setup_switches iterates through dst->ports, initializing
the Switch 1 ds structure (invalid) and the Switch 2 ds structure
(valid).
- Undefined behavior (use after free, sometimes NULL pointers, etc).
Real example below (debugging prints added by me, as well as guards
against NULL pointers):
[ 5.477947] dsa_tree_setup_switches: Setting up port 0 of switch ffffff803df0b980 (dev ffffff803f775c00)
[ 6.313002] dsa_tree_setup_switches: Setting up port 1 of switch ffffff803df0b980 (dev ffffff803f775c00)
[ 6.319932] dsa_tree_setup_switches: Setting up port 2 of switch ffffff803df0b980 (dev ffffff803f775c00)
[ 6.329693] dsa_tree_setup_switches: Setting up port 3 of switch ffffff803df0b980 (dev ffffff803f775c00)
[ 6.339458] dsa_tree_setup_switches: Setting up port 4 of switch ffffff803df0b980 (dev ffffff803f775c00)
[ 6.349226] dsa_tree_setup_switches: Setting up port 5 of switch ffffff803df0b980 (dev ffffff803f775c00)
[ 6.358991] dsa_tree_setup_switches: Setting up port 6 of switch ffffff803df0b980 (dev ffffff803f775c00)
[ 6.368758] dsa_tree_setup_switches: Setting up port 7 of switch ffffff803df0b980 (dev ffffff803f775c00)
[ 6.378524] dsa_tree_setup_switches: Setting up port 8 of switch ffffff803df0b980 (dev ffffff803f775c00)
[ 6.388291] dsa_tree_setup_switches: Setting up port 9 of switch ffffff803df0b980 (dev ffffff803f775c00)
[ 6.398057] dsa_tree_setup_switches: Setting up port 10 of switch ffffff803df0b980 (dev ffffff803f775c00)
[ 6.407912] dsa_tree_setup_switches: Setting up port 0 of switch ffffff803da02f80 (dev 0000000000000000)
[ 6.417682] dsa_tree_setup_switches: Setting up port 1 of switch ffffff803da02f80 (dev 0000000000000000)
[ 6.427446] dsa_tree_setup_switches: Setting up port 2 of switch ffffff803da02f80 (dev 0000000000000000)
[ 6.437212] dsa_tree_setup_switches: Setting up port 3 of switch ffffff803da02f80 (dev 0000000000000000)
[ 6.446979] dsa_tree_setup_switches: Setting up port 4 of switch ffffff803da02f80 (dev 0000000000000000)
[ 6.456744] dsa_tree_setup_switches: Setting up port 5 of switch ffffff803da02f80 (dev 0000000000000000)
[ 6.466512] dsa_tree_setup_switches: Setting up port 6 of switch ffffff803da02f80 (dev 0000000000000000)
[ 6.476277] dsa_tree_setup_switches: Setting up port 7 of switch ffffff803da02f80 (dev 0000000000000000)
[ 6.486043] dsa_tree_setup_switches: Setting up port 8 of switch ffffff803da02f80 (dev 0000000000000000)
[ 6.495810] dsa_tree_setup_switches: Setting up port 9 of switch ffffff803da02f80 (dev 0000000000000000)
[ 6.505577] dsa_tree_setup_switches: Setting up port 10 of switch ffffff803da02f80 (dev 0000000000000000)
[ 6.515433] dsa_tree_setup_switches: Setting up port 0 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[ 7.354120] dsa_tree_setup_switches: Setting up port 1 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[ 7.361045] dsa_tree_setup_switches: Setting up port 2 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[ 7.370805] dsa_tree_setup_switches: Setting up port 3 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[ 7.380571] dsa_tree_setup_switches: Setting up port 4 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[ 7.390337] dsa_tree_setup_switches: Setting up port 5 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[ 7.400104] dsa_tree_setup_switches: Setting up port 6 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[ 7.409872] dsa_tree_setup_switches: Setting up port 7 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[ 7.419637] dsa_tree_setup_switches: Setting up port 8 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[ 7.429403] dsa_tree_setup_switches: Setting up port 9 of switch ffffff803db15b80 (dev ffffff803d8e4800)
[ 7.439169] dsa_tree_setup_switches: Setting up port 10 of switch ffffff803db15b80 (dev ffffff803d8e4800)
The solution is to recognize that the functions that call
dsa_switch_touch_ports (dsa_switch_parse_of, dsa_switch_parse) have side
effects, and therefore one should clean up their side effects on error
path. The cleanup of dst->ports was taken from dsa_switch_remove and
moved into a dedicated dsa_switch_release_ports function, which should
really be per-switch (free only the members of dst->ports that are also
members of ds, instead of all switch ports).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA subsystem takes care of netdev statistics since commit 4ed70ce9f0
("net: dsa: Refactor transmit path to eliminate duplication"), so
any accounting inside tagger callbacks is redundant and can lead to
messing up the stats.
This bug is present in Qualcomm tagger since day 0.
Fixes: cafdc45c94 ("net-next: dsa: add Qualcomm tag RX/TX handler")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct name is GSWIP (Gigabit Switch IP). Typo was introduced in
875138f81d ("dsa: Move tagger name into its ops structure") while
moving tagger names to their structures.
Fixes: 875138f81d ("dsa: Move tagger name into its ops structure")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to stack multiple DSA switches in a way that they are not
part of the tree (disjoint) but the DSA master of a switch is a DSA
slave of another. When that happens switch drivers may have to know this
is the case so as to determine whether their tagging protocol has a
remove chance of working.
This is useful for specific switch drivers such as b53 where devices
have been known to be stacked in the wild without the Broadcom tag
protocol supporting that feature. This allows b53 to continue supporting
those devices by forcing the disabling of Broadcom tags on the outermost
switches if necessary.
The get_tag_protocol() function is therefore updated to gain an
additional enum dsa_tag_protocol argument which denotes the current
tagging protocol used by the DSA master we are attached to, else
DSA_TAG_PROTO_NONE for the top of the dsa_switch_tree.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA drivers that implement .phylink_mac_link_state should normally
register an interrupt for the PCS, from which they should call
phylink_mac_change(). However not all switches implement this, and those
who don't should set this flag in dsa_switch in the .setup callback, so
that PHYLINK will poll for a few ms until the in-band AN link timer
expires and the PCS state settles.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic patch that makes the dp, tx_vid, queue_mapping and
pcp local variable definitions a bit closer in length, so they don't
look like an eyesore as much.
The 'ds' variable is not used otherwise, except for ds->dp.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 3 things that are wrong with the DSA deferred xmit mechanism:
1. Its introduction has made the DSA hotpath ever so slightly more
inefficient for everybody, since DSA_SKB_CB(skb)->deferred_xmit needs
to be initialized to false for every transmitted frame, in order to
figure out whether the driver requested deferral or not (a very rare
occasion, rare even for the only driver that does use this mechanism:
sja1105). That was necessary to avoid kfree_skb from freeing the skb.
2. Because L2 PTP is a link-local protocol like STP, it requires
management routes and deferred xmit with this switch. But as opposed
to STP, the deferred work mechanism needs to schedule the packet
rather quickly for the TX timstamp to be collected in time and sent
to user space. But there is no provision for controlling the
scheduling priority of this deferred xmit workqueue. Too bad this is
a rather specific requirement for a feature that nobody else uses
(more below).
3. Perhaps most importantly, it makes the DSA core adhere a bit too
much to the NXP company-wide policy "Innovate Where It Doesn't
Matter". The sja1105 is probably the only DSA switch that requires
some frames sent from the CPU to be routed to the slave port via an
out-of-band configuration (register write) rather than in-band (DSA
tag). And there are indeed very good reasons to not want to do that:
if that out-of-band register is at the other end of a slow bus such
as SPI, then you limit that Ethernet flow's throughput to effectively
the throughput of the SPI bus. So hardware vendors should definitely
not be encouraged to design this way. We do _not_ want more
widespread use of this mechanism.
Luckily we have a solution for each of the 3 issues:
For 1, we can just remove that variable in the skb->cb and counteract
the effect of kfree_skb with skb_get, much to the same effect. The
advantage, of course, being that anybody who doesn't use deferred xmit
doesn't need to do any extra operation in the hotpath.
For 2, we can create a kernel thread for each port's deferred xmit work.
If the user switch ports are named swp0, swp1, swp2, the kernel threads
will be named swp0_xmit, swp1_xmit, swp2_xmit (there appears to be a 15
character length limit on kernel thread names). With this, the user can
change the scheduling priority with chrt $(pidof swp2_xmit).
For 3, we can actually move the entire implementation to the sja1105
driver.
So this patch deletes the generic implementation from the DSA core and
adds a new one, more adequate to the requirements of PTP TX
timestamping, in sja1105_main.c.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to kill PTP on a DSA switch completely and absolutely,
until a reboot, with a simple command:
tcpdump -i eth2 -j adapter_unsynced
where eth2 is the switch's DSA master.
Why? Well, in short, the PTP API in place today is a bit rudimentary and
relies on applications to retrieve the TX timestamps by polling the
error queue and looking at the cmsg structure. But there is no timestamp
identification of any sorts (except whether it's HW or SW), you don't
know how many more timestamps are there to come, which one is this one,
from whom it is, etc. In other words, the SO_TIMESTAMPING API is
fundamentally limited in that you can get a single HW timestamp from the
stack.
And the "-j adapter_unsynced" flag of tcpdump enables hardware
timestamping.
So let's imagine what happens when the DSA master decides it wants to
deliver TX timestamps to the skb's socket too:
- The timestamp that the user space sees is taken by the DSA master.
Whereas the RX timestamp will eventually be overwritten by the DSA
switch. So the RX and TX timestamps will be in different time bases
(aka garbage).
- The user space applications have no way to deal with the second (real)
TX timestamp finally delivered by the DSA switch, or even to know to
wait for it.
Take ptp4l from the linuxptp project, for example. This is its behavior
after running tcpdump, before the patch:
ptp4l[172]: [6469.594] Unexpected data on socket err queue:
ptp4l[172]: [6469.693] rms 8 max 16 freq -21257 +/- 11 delay 748 +/- 0
ptp4l[172]: [6469.711] Unexpected data on socket err queue:
ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 03 aa 05 00 fd
ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: [6469.721] Unexpected data on socket err queue:
ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 10 02
ptp4l[172]: 0010 00 2c 00 00 02 00 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 01 c6 b1 00 fd
ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: [6469.838] Unexpected data on socket err queue:
ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 10 02
ptp4l[172]: 0010 00 2c 00 00 02 00 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 03 aa 06 00 fd
ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: [6469.848] Unexpected data on socket err queue:
ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 13 02
ptp4l[172]: 0010 00 36 00 00 02 00 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 04 1a 45 05 7f
ptp4l[172]: 0030 00 00 5e 05 41 32 27 c2 1a 68 00 04 9f ff fe 05
ptp4l[172]: 0040 de 06 00 01
ptp4l[172]: [6469.855] Unexpected data on socket err queue:
ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 10 02
ptp4l[172]: 0010 00 2c 00 00 02 00 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 01 c6 b2 00 fd
ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: [6469.974] Unexpected data on socket err queue:
ptp4l[172]: 0000 01 80 c2 00 00 0e 00 1f 7b 63 02 48 88 f7 10 02
ptp4l[172]: 0010 00 2c 00 00 02 00 00 00 00 00 00 00 00 00 00 00
ptp4l[172]: 0020 00 00 00 1f 7b ff fe 63 02 48 00 03 aa 07 00 fd
ptp4l[172]: 0030 00 00 00 00 00 00 00 00 00 00
The ptp4l program itself is heavily patched to show this (more details
here [0]). Otherwise, by default it just hangs.
On the other hand, with the DSA patch to disallow HW timestamping
applied:
tcpdump -i eth2 -j adapter_unsynced
tcpdump: SIOCSHWTSTAMP failed: Device or resource busy
So it is a fact of life that PTP timestamping on the DSA master is
incompatible with timestamping on the switch MAC, at least with the
current API. And if the switch supports PTP, taking the timestamps from
the switch MAC is highly preferable anyway, due to the fact that those
don't contain the queuing latencies of the switch. So just disallow PTP
on the DSA master if there is any PTP-capable switch attached.
[0]: https://sourceforge.net/p/linuxptp/mailman/message/36880648/
Fixes: 0336369d3a ("net: dsa: forward hardware timestamping ioctls to switch driver")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove special taglen define KSZ8795_INGRESS_TAG_LEN
and use generic KSZ_INGRESS_TAG_LEN instead.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for tag format used in Atheros AR9331 built-in switch.
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_link_touch() is not exported, or defined outside of the
file it is in so make it static to avoid the following warning:
net/dsa/dsa2.c:127:17: warning: symbol 'dsa_link_touch' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 77373d49de ("net: dsa: Move the phylink driver calls into
port.c") moved and exported a bunch of symbols, but they are not used
outside of net/dsa/port.c at the moment, so no reason to export them.
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the mac_link_state() method to mac_pcs_get_state() to make it
clear that it should be returning the MACs PCS current state, which
is used for inband negotiation rather than just reading back what the
MAC has been configured for. Update the documentation to explicitly
mention that this is for inband.
We drop the return value as well; most of phylink doesn't check the
return value and it is not clear what it should do on error - instead
arrange for state->link to be false.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch is to reuse ocelot functions as possible to enable PTP
clock and to support hardware timestamping on Felix.
On TX path, timestamping works on packet which requires timestamp.
The injection header will be configured accordingly, and skb clone
requires timestamp will be added into a list. The TX timestamp
is final handled in threaded interrupt handler when PTP timestamp
FIFO is ready.
On RX path, timestamping is always working. The RX timestamp could
be got from extraction header.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This sequence of operations:
ip link set dev br0 type bridge vlan_filtering 1
bridge vlan del dev swp2 vid 1
ip link set dev br0 type bridge vlan_filtering 1
ip link set dev br0 type bridge vlan_filtering 0
apparently fails with the message:
[ 31.305716] sja1105 spi0.1: Reset switch and programmed static config. Reason: VLAN filtering
[ 31.322161] sja1105 spi0.1: Couldn't determine PVID attributes (pvid 0)
[ 31.328939] sja1105 spi0.1: Failed to setup VLAN tagging for port 1: -2
[ 31.335599] ------------[ cut here ]------------
[ 31.340215] WARNING: CPU: 1 PID: 194 at net/switchdev/switchdev.c:157 switchdev_port_attr_set_now+0x9c/0xa4
[ 31.349981] br0: Commit of attribute (id=6) failed.
[ 31.354890] Modules linked in:
[ 31.357942] CPU: 1 PID: 194 Comm: ip Not tainted 5.4.0-rc6-01792-gf4f632e07665-dirty #2062
[ 31.366167] Hardware name: Freescale LS1021A
[ 31.370437] [<c03144dc>] (unwind_backtrace) from [<c030e184>] (show_stack+0x10/0x14)
[ 31.378153] [<c030e184>] (show_stack) from [<c11d1c1c>] (dump_stack+0xe0/0x10c)
[ 31.385437] [<c11d1c1c>] (dump_stack) from [<c034c730>] (__warn+0xf4/0x10c)
[ 31.392373] [<c034c730>] (__warn) from [<c034c7bc>] (warn_slowpath_fmt+0x74/0xb8)
[ 31.399827] [<c034c7bc>] (warn_slowpath_fmt) from [<c11ca204>] (switchdev_port_attr_set_now+0x9c/0xa4)
[ 31.409097] [<c11ca204>] (switchdev_port_attr_set_now) from [<c117036c>] (__br_vlan_filter_toggle+0x6c/0x118)
[ 31.418971] [<c117036c>] (__br_vlan_filter_toggle) from [<c115d010>] (br_changelink+0xf8/0x518)
[ 31.427637] [<c115d010>] (br_changelink) from [<c0f8e9ec>] (__rtnl_newlink+0x3f4/0x76c)
[ 31.435613] [<c0f8e9ec>] (__rtnl_newlink) from [<c0f8eda8>] (rtnl_newlink+0x44/0x60)
[ 31.443329] [<c0f8eda8>] (rtnl_newlink) from [<c0f89f20>] (rtnetlink_rcv_msg+0x2cc/0x51c)
[ 31.451477] [<c0f89f20>] (rtnetlink_rcv_msg) from [<c1008df8>] (netlink_rcv_skb+0xb8/0x110)
[ 31.459796] [<c1008df8>] (netlink_rcv_skb) from [<c1008648>] (netlink_unicast+0x17c/0x1f8)
[ 31.468026] [<c1008648>] (netlink_unicast) from [<c1008980>] (netlink_sendmsg+0x2bc/0x3b4)
[ 31.476261] [<c1008980>] (netlink_sendmsg) from [<c0f43858>] (___sys_sendmsg+0x230/0x250)
[ 31.484408] [<c0f43858>] (___sys_sendmsg) from [<c0f44c84>] (__sys_sendmsg+0x50/0x8c)
[ 31.492209] [<c0f44c84>] (__sys_sendmsg) from [<c0301000>] (ret_fast_syscall+0x0/0x28)
[ 31.500090] Exception stack(0xedf47fa8 to 0xedf47ff0)
[ 31.505122] 7fa0: 00000002 b6f2e060 00000003 beabd6a4 00000000 00000000
[ 31.513265] 7fc0: 00000002 b6f2e060 5d6e3213 00000128 00000000 00000001 00000006 000619c4
[ 31.521405] 7fe0: 00086078 beabd658 0005edbc b6e7ce68
The reason is the implementation of br_get_pvid:
static inline u16 br_get_pvid(const struct net_bridge_vlan_group *vg)
{
if (!vg)
return 0;
smp_rmb();
return vg->pvid;
}
Since VID 0 is an invalid pvid from the bridge's point of view, let's
add this check in dsa_8021q_restore_pvid to avoid restoring a pvid that
doesn't really exist.
Fixes: 5f33183b7f ("net: dsa: tag_8021q: Restore bridge VLANs when enabling vlan_filtering")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
While it is entirely possible that this tagger format is in fact more
generic than just these 2 switch families, I don't have that knowledge.
The Seville switch in NXP T1040 has a similar frame format, but there
are enough differences (e.g. DEST field starts at bit 57 instead of 56)
that calling this file tag_vitesse.c is a bit of a stretch at the
moment. The frame format has been listed in a comment so that people who
add support for further Vitesse switches can rework this tagger while
keeping compatibility with Felix.
The "ocelot" name was chosen instead of "felix" because even the Ocelot
switch can act as a DSA device when it is used in NPI mode, and the Felix
tagger format is almost identical. Currently it is only used for the
Felix switch embedded in the NXP LS1028A chip.
The ABI for this tagger should be considered "not stable" at the moment.
The DSA tag is always placed before the Ethernet header and therefore,
we are using the long prefix for RX tags to avoid putting the DSA master
port in promiscuous mode. Once there will be an API in DSA for drivers
to request DSA masters to be in promiscuous mode unconditionally, we
will switch to the "no prefix" extraction frame header, which will save
16 padding bytes for each RX frame.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for a switch driver to use NET_DSA_TAG_8021Q as a valid
DSA tagging protocol since it registers itself as such, unfortunately
since there are not xmit or rcv functions provided, the lack of a xmit()
function will lead to a NPD in dsa_slave_xmit() to start with.
net/dsa/tag_8021q.c is only comprised of a set of helper functions at
the moment, but is not a fully autonomous or functional tagging "driver"
(though it could become later on). We do not have any users of
NET_DSA_TAG_8021Q so now is a good time to make sure there are not
issues being encountered by making this file strictly a place holder for
helper functions.
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wrappers around the devlink resource API, so that DSA drivers can
register and unregister devlink resources.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The order in which the ports are deleted from the list and freed and the
call to dsa_switch_remove() is done is reversed, which leads to an
use after free condition. Reverse the two: first tear down the ports and
switch from the fabric, then free the ports associated with that switch
fabric.
Fixes: 05f294a852 ("net: dsa: allocate ports on touch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there's no restriction from the DSA core side regarding
the switch IDs and port numbers, only tag_8021q which is currently
reserving 3 bits for the switch ID and 4 bits for the port number, has
limitation for these values. Update their descriptions to reflect that.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because there is no static array describing the links between switches
anymore, we have no reason to force a limitation of the index value
set by the device tree.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA fabric setup code has been simplified a lot so get rid of
the dsa_tree_remove_switch, dsa_tree_add_switch and dsa_switch_add
helpers, and keep the code simple with only the dsa_switch_probe and
dsa_switch_remove functions.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the DSA ports are listed in the switch fabric, there is
no need to store the dsa_switch structures from the drivers in the
fabric anymore. So get rid of the dst->ds static array.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_switch structure has no routing table specific data to setup,
so the switch fabric can directly walk its ports and initialize its
routing table from them.
This allows us to remove the dsa_switch_setup_routing_table function.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers do not use the ds->rtable static arrays anymore, get rid of it.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a new list of DSA links in the switch fabric itself, to
provide an alterative to the ds->rtable static arrays.
At the same time, provide a new dsa_routing_port() helper to abstract
the usage of ds->rtable in drivers. If there's no port to reach a
given device, return the first invalid port, ds->num_ports. This avoids
potential signedness errors or the need to define special values.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds glue logic to make pause settings per port
configurable vie ethtool.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add plumbing to allow DSA drivers to register parameters with devlink.
To keep with the abstraction, the DSA drivers pass the ds structure to
these helpers, and the DSA core then translates that to the devlink
structure associated to the device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ds->dev is dereferenced on the assignments of pdata and
np before ds->dev is null checked, hence there is a potential null
pointer dereference on ds->dev. Fix this by assigning pdata and
np after the ds->dev null pointer sanity check.
Addresses-Coverity: ("Dereference before null check")
Fixes: 7e99e34701 ("net: dsa: remove dsa_switch_alloc helper")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some interface types could be nested.
(VLAN, BONDING, TEAM, MACSEC, MACVLAN, IPVLAN, VIRT_WIFI, VXLAN, etc..)
These interface types should set lockdep class because, without lockdep
class key, lockdep always warn about unexisting circular locking.
In the current code, these interfaces have their own lockdep class keys and
these manage itself. So that there are so many duplicate code around the
/driver/net and /net/.
This patch adds new generic lockdep keys and some helper functions for it.
This patch does below changes.
a) Add lockdep class keys in struct net_device
- qdisc_running, xmit, addr_list, qdisc_busylock
- these keys are used as dynamic lockdep key.
b) When net_device is being allocated, lockdep keys are registered.
- alloc_netdev_mqs()
c) When net_device is being free'd llockdep keys are unregistered.
- free_netdev()
d) Add generic lockdep key helper function
- netdev_register_lockdep_key()
- netdev_unregister_lockdep_key()
- netdev_update_lockdep_key()
e) Remove unnecessary generic lockdep macro and functions
f) Remove unnecessary lockdep code of each interfaces.
After this patch, each interface modules don't need to maintain
their lockdep keys.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that ports are dynamically listed in the fabric, there is no need
to provide a special helper to allocate the dsa_switch structure. This
will give more flexibility to drivers to embed this structure as they
wish in their private structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Allocate the struct dsa_port the first time it is accessed with
dsa_port_touch, and remove the static dsa_port array from the
dsa_switch structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Use the new ports list instead of iterating over switches and their
ports when setting up the default CPU port. Unassign it on teardown.
Now that we can iterate over multiple CPU ports, remove dst->cpu_dp.
At the same time, provide a better error message for CPU-less tree.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Use the new ports list instead of iterating over switches and their
ports when looking up the first CPU port in the tree.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Now that we have a potential list of CPU ports, make use of it instead
of only configuring the master device of an unique CPU port.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Use the new ports list instead of iterating over switches and their
ports to find a port from a given node.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Use the new ports list instead of accessing the dsa_switch array
of ports when iterating over DSA ports of a switch to set up the
routing table.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Use the new ports list instead of iterating over switches and their
ports when setting up the switches and their ports.
At the same time, provide setup states and messages for ports and
switches as it is done for the trees.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Use the new ports list instead of iterating over switches and their
ports when looking for a slave device from a given master interface.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Add a list of switch ports within the switch fabric. This will help the
lookup of a port inside the whole fabric, and it is the first step
towards supporting multiple CPU ports, before deprecating the usage of
the unique dst->cpu_dp pointer.
In preparation for a future allocation of the dsa_port structures,
return -ENOMEM in case no structure is returned, even though this
error cannot be reached yet.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Do not let the drivers access the ds->ports static array directly
while there is a dsa_to_port helper for this purpose.
At the same time, un-const this helper since the SJA1105 driver
assigns the priv member of the returned dsa_port structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
If there are multiple switch trees on the device, only the last one
will be listed, because the arguments of list_add_tail are swapped.
Fixes: 83c0afaec7 ("net: dsa: Add new binding implementation")
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently this stack trace can be seen with CONFIG_DEBUG_ATOMIC_SLEEP=y:
[ 41.568348] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:909
[ 41.576757] in_atomic(): 1, irqs_disabled(): 0, pid: 208, name: ptp4l
[ 41.583212] INFO: lockdep is turned off.
[ 41.587123] CPU: 1 PID: 208 Comm: ptp4l Not tainted 5.3.0-rc6-01445-ge950f2d4bc7f-dirty #1827
[ 41.599873] [<c0313d7c>] (unwind_backtrace) from [<c030e13c>] (show_stack+0x10/0x14)
[ 41.607584] [<c030e13c>] (show_stack) from [<c1212d50>] (dump_stack+0xd4/0x100)
[ 41.614863] [<c1212d50>] (dump_stack) from [<c037dfc8>] (___might_sleep+0x1c8/0x2b4)
[ 41.622574] [<c037dfc8>] (___might_sleep) from [<c122ea90>] (__mutex_lock+0x48/0xab8)
[ 41.630368] [<c122ea90>] (__mutex_lock) from [<c122f51c>] (mutex_lock_nested+0x1c/0x24)
[ 41.638340] [<c122f51c>] (mutex_lock_nested) from [<c0c6fe08>] (sja1105_static_config_reload+0x30/0x27c)
[ 41.647779] [<c0c6fe08>] (sja1105_static_config_reload) from [<c0c7015c>] (sja1105_hwtstamp_set+0x108/0x1cc)
[ 41.657562] [<c0c7015c>] (sja1105_hwtstamp_set) from [<c0feb650>] (dev_ifsioc+0x18c/0x330)
[ 41.665788] [<c0feb650>] (dev_ifsioc) from [<c0febbd8>] (dev_ioctl+0x320/0x6e8)
[ 41.673064] [<c0febbd8>] (dev_ioctl) from [<c0f8b1f4>] (sock_ioctl+0x334/0x5e8)
[ 41.680340] [<c0f8b1f4>] (sock_ioctl) from [<c05404a8>] (do_vfs_ioctl+0xb0/0xa10)
[ 41.687789] [<c05404a8>] (do_vfs_ioctl) from [<c0540e3c>] (ksys_ioctl+0x34/0x58)
[ 41.695151] [<c0540e3c>] (ksys_ioctl) from [<c0301000>] (ret_fast_syscall+0x0/0x28)
[ 41.702768] Exception stack(0xe8495fa8 to 0xe8495ff0)
[ 41.707796] 5fa0: beff4a8c 00000001 00000011 000089b0 beff4a8c beff4a80
[ 41.715933] 5fc0: beff4a8c 00000001 0000000c 00000036 b6fa98c8 004e19c1 00000001 00000000
[ 41.724069] 5fe0: 004dcedc beff4a6c 004c0738 b6e7af4c
[ 41.729860] BUG: scheduling while atomic: ptp4l/208/0x00000002
[ 41.735682] INFO: lockdep is turned off.
Enabling RX timestamping will logically disturb the fastpath (processing
of meta frames). Replace bool hwts_rx_en with a bit that is checked
atomically from the fastpath and temporarily unset from the sleepable
context during a change of the RX timestamping process (a destructive
operation anyways, requires switch reset).
If found unset, the fastpath (net/dsa/tag_sja1105.c) will just drop any
received meta frame and not take the meta_lock at all.
Fixes: a602afd200 ("net: dsa: sja1105: Expose PTP timestamping ioctls to userspace")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a preparation patch for the tc-taprio offload (and potentially
for other future offloads such as tc-mqprio).
Instead of looking directly at skb->priority during xmit, let's get the
netdev queue and the queue-to-traffic-class mapping, and put the
resulting traffic class into the dsa_8021q PCP field. The switch is
configured with a 1-to-1 PCP-to-ingress-queue-to-egress-queue mapping
(see vlan_pmap in sja1105_main.c), so the effect is that we can inject
into a front-panel's egress traffic class through VLAN tagging from
Linux, completely transparently.
Unfortunately the switch doesn't look at the VLAN PCP in the case of
management traffic to/from the CPU (link-local frames at
01-80-C2-xx-xx-xx or 01-1B-19-xx-xx-xx) so we can't alter the
transmission queue of this type of traffic on a frame-by-frame basis. It
is only selected through the "hostprio" setting which ATM is harcoded in
the driver to 7.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA currently handles shared block filters (for the classifier-action
qdisc) in the core due to what I believe are simply pragmatic reasons -
hiding the complexity from drivers and offerring a simple API for port
mirroring.
Extend the dsa_slave_setup_tc function by passing all other qdisc
offloads to the driver layer, where the driver may choose what it
implements and how. DSA is simply a pass-through in this case.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA core, DSA taggers and DSA drivers all make use of
module_init(). Hence they get initialised at device_initcall() time.
The ordering is non-deterministic. It can be a DSA driver is bound to
a device before the needed tag driver has been initialised, resulting
in the message:
No tagger for this switch
Rather than have this be fatal, return -EPROBE_DEFER so that it is
tried again later once all the needed drivers have been loaded.
Fixes: d3b8c04988 ("dsa: Add boilerplate helper to register DSA tag driver modules")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the superfluous NET_DSA_TAG_KSZ_COMMON and just use the existing
NET_DSA_TAG_KSZ. Update the description to mention the three switch
families it supports. No functional change.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a function such as dsa_slave_create fails, currently the following
stack trace can be seen:
[ 2.038342] sja1105 spi0.1: Probed switch chip: SJA1105T
[ 2.054556] sja1105 spi0.1: Reset switch and programmed static config
[ 2.063837] sja1105 spi0.1: Enabled switch tagging
[ 2.068706] fsl-gianfar soc:ethernet@2d90000 eth2: error -19 setting up slave phy
[ 2.076371] ------------[ cut here ]------------
[ 2.080973] WARNING: CPU: 1 PID: 21 at net/core/devlink.c:6184 devlink_free+0x1b4/0x1c0
[ 2.088954] Modules linked in:
[ 2.092005] CPU: 1 PID: 21 Comm: kworker/1:1 Not tainted 5.3.0-rc6-01360-g41b52e38d2b6-dirty #1746
[ 2.100912] Hardware name: Freescale LS1021A
[ 2.105162] Workqueue: events deferred_probe_work_func
[ 2.110287] [<c03133a4>] (unwind_backtrace) from [<c030d8cc>] (show_stack+0x10/0x14)
[ 2.117992] [<c030d8cc>] (show_stack) from [<c10b08d8>] (dump_stack+0xb4/0xc8)
[ 2.125180] [<c10b08d8>] (dump_stack) from [<c0349d04>] (__warn+0xe0/0xf8)
[ 2.132018] [<c0349d04>] (__warn) from [<c0349e34>] (warn_slowpath_null+0x40/0x48)
[ 2.139549] [<c0349e34>] (warn_slowpath_null) from [<c0f19d74>] (devlink_free+0x1b4/0x1c0)
[ 2.147772] [<c0f19d74>] (devlink_free) from [<c1064fc0>] (dsa_switch_teardown+0x60/0x6c)
[ 2.155907] [<c1064fc0>] (dsa_switch_teardown) from [<c1065950>] (dsa_register_switch+0x8e4/0xaa8)
[ 2.164821] [<c1065950>] (dsa_register_switch) from [<c0ba7fe4>] (sja1105_probe+0x21c/0x2ec)
[ 2.173216] [<c0ba7fe4>] (sja1105_probe) from [<c0b35948>] (spi_drv_probe+0x80/0xa4)
[ 2.180920] [<c0b35948>] (spi_drv_probe) from [<c0a4c1cc>] (really_probe+0x108/0x400)
[ 2.188711] [<c0a4c1cc>] (really_probe) from [<c0a4c694>] (driver_probe_device+0x78/0x1bc)
[ 2.196933] [<c0a4c694>] (driver_probe_device) from [<c0a4a3dc>] (bus_for_each_drv+0x58/0xb8)
[ 2.205414] [<c0a4a3dc>] (bus_for_each_drv) from [<c0a4c024>] (__device_attach+0xd0/0x168)
[ 2.213637] [<c0a4c024>] (__device_attach) from [<c0a4b1d0>] (bus_probe_device+0x84/0x8c)
[ 2.221772] [<c0a4b1d0>] (bus_probe_device) from [<c0a4b72c>] (deferred_probe_work_func+0x84/0xc4)
[ 2.230686] [<c0a4b72c>] (deferred_probe_work_func) from [<c03650a4>] (process_one_work+0x218/0x510)
[ 2.239772] [<c03650a4>] (process_one_work) from [<c03660d8>] (worker_thread+0x2a8/0x5c0)
[ 2.247908] [<c03660d8>] (worker_thread) from [<c036b348>] (kthread+0x148/0x150)
[ 2.255265] [<c036b348>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
[ 2.262444] Exception stack(0xea965fb0 to 0xea965ff8)
[ 2.267466] 5fa0: 00000000 00000000 00000000 00000000
[ 2.275598] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 2.283729] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 2.290333] ---[ end trace ca5d506728a0581a ]---
devlink_free is complaining right here:
WARN_ON(!list_empty(&devlink->port_list));
This happens because devlink_port_unregister is no longer done right
away in dsa_port_setup when a DSA_PORT_TYPE_USER has failed.
Vivien said about this change that:
Also no need to call devlink_port_unregister from within dsa_port_setup
as this step is inconditionally handled by dsa_port_teardown on error.
which is not really true. The devlink_port_unregister function _is_
being called unconditionally from within dsa_port_setup, but not for
this port that just failed, just for the previous ones which were set
up.
ports_teardown:
for (i = 0; i < port; i++)
dsa_port_teardown(&ds->ports[i]);
Initially I was tempted to fix this by extending the "for" loop to also
cover the port that failed during setup. But this could have potentially
unforeseen consequences unrelated to devlink_port or even other types of
ports than user ports, which I can't really test for. For example, if
for some reason devlink_port_register itself would fail, then
unconditionally unregistering it in dsa_port_teardown would not be a
smart idea. The list might go on.
So just make dsa_port_setup undo the setup it had done upon failure, and
let the for loop undo the work of setting up the previous ports, which
are guaranteed to be brought up to a consistent state.
Fixes: 955222ca52 ("net: dsa: use a single switch statement for port setup")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge core assumes that enabling/disabling vlan_filtering will
translate into the simple toggling of a flag for switchdev drivers.
That is clearly not the case for sja1105, which alters the VLAN table
and the pvids in order to obtain port separation in standalone mode.
There are 2 parts to the issue.
First, tag_8021q changes the pvid to a unique per-port rx_vid for frame
identification. But we need to disable tag_8021q when vlan_filtering
kicks in, and at that point, the VLAN configured as pvid will have to be
removed from the filtering table of the ports. With an invalid pvid, the
ports will drop all traffic. Since the bridge will not call any vlan
operation through switchdev after enabling vlan_filtering, we need to
ensure we're in a functional state ourselves. Hence read the pvid that
the bridge is aware of, and program that into our ports.
Secondly, tag_8021q uses the 1024-3071 range privately in
vlan_filtering=0 mode. Had the user installed one of these VLANs during
a previous vlan_filtering=1 session, then upon the next tag_8021q
cleanup for vlan_filtering to kick in again, VLANs in that range will
get deleted unconditionally, hence breaking user expectation. So when
deleting the VLANs, check if the bridge had knowledge about them, and if
it did, re-apply the settings. Wrap this logic inside a
dsa_8021q_vid_apply helper function to reduce code duplication.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding a VLAN sub-interface on a DSA slave port, the 8021q core
checks NETIF_F_HW_VLAN_CTAG_FILTER and, if the netdev is capable of
filtering, calls .ndo_vlan_rx_add_vid or .ndo_vlan_rx_kill_vid to
configure the VLAN offloading.
DSA sets this up counter-intuitively: it always advertises this netdev
feature, but the underlying driver may not actually support VLAN table
manipulation. In that case, the DSA core is forced to ignore the error,
because not being able to offload the VLAN is still fine - and should
result in the creation of a non-accelerated VLAN sub-interface.
Change this so that the netdev feature is only advertised for switch
drivers that support VLAN manipulation, instead of checking for
-EOPNOTSUPP at runtime.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After witnessing the discussion in https://lkml.org/lkml/2019/8/14/151
w.r.t. ioctl extensibility, it became clear that such an issue might
prevent that the 3 RSV bits inside the DSA 802.1Q tag might also suffer
the same fate and be useless for further extension.
So clearly specify that the reserved bits should currently be
transmitted as zero and ignored on receive. The DSA tagger already does
this (and has always did), and is the only known user so far (no
Wireshark dissection plugin, etc). So there should be no incompatibility
to speak of.
Fixes: 0471dd429c ("net: dsa: tag_8021q: Create a stable binary format")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the bridge offloads a VLAN on a slave port, we also need to
program its dedicated CPU port as a member of the VLAN.
Drivers may handle the CPU port's membership as they want. For example,
Marvell as a special "Unmodified" mode to pass frames as is through
such ports.
Even though DSA expects the drivers to handle the CPU port membership,
it does not make sense to program user VLANs as PVID on the CPU port.
This patch clears this flag before programming the CPU port.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA currently programs a VLAN on the CPU port implicitly after the
related notifier is received by a switch.
While we still need to do this transparent programmation of the DSA
links in the fabric, programming the CPU port this way may cause
problems in some corners such as the tag_8021q driver.
Because the dedicated CPU port is specific to a slave, make their
programmation explicit a few layers up, in the slave code.
Note that technically, DSA links have a dedicated CPU port as well,
but since they are only used as conduit between interconnected switches
of a fabric, programming them transparently this way is what we want.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge VLANs are not offloaded by dsa_port_vlan_* if the port is
not bridged or if its bridge is not VLAN aware.
This is a good thing but other corners of DSA, such as the tag_8021q
driver, may need to program VLANs regardless the bridge state.
And also because bridge_dev is specific to user ports anyway, move
these checks were it belongs, one layer up in the slave code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dsa_slave_vlan_add and dsa_slave_vlan_del helpers to handle
SWITCHDEV_OBJ_ID_PORT_VLAN switchdev objects. Also copy the
switchdev_obj_port_vlan structure on add since we will modify it in
future patches.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently dsa_port_vid_add returns 0 if the switch returns -EOPNOTSUPP.
This function is used in the tag_8021q.c code to offload the PVID of
ports, which would simply not work if .port_vlan_add is not supported
by the underlying switch.
Do not skip -EOPNOTSUPP in dsa_port_vid_add but only when necessary,
that is to say in dsa_slave_vlan_rx_add_vid.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bitmap operations were introduced to simplify the switch drivers
in the future, since most of them could implement the common VLAN and
MDB operations (add, del, dump) with simple functions taking all target
ports at once, and thus limiting the number of hardware accesses.
Programming an MDB or VLAN this way in a single operation would clearly
simplify the drivers a lot but would require a new get-set interface
in DSA. The usage of such bitmap from the stack also raised concerned
in the past, leading to the dynamic allocation of a new ds->_bitmap
member in the dsa_switch structure. So let's get rid of them for now.
This commit nicely wraps the ds->ops->port_{mdb,vlan}_{prepare,add}
switch operations into new dsa_switch_{mdb,vlan}_{prepare,add}
variants not using any bitmap argument anymore.
New dsa_switch_{mdb,vlan}_match helpers have been introduced to make
clear which local port of a switch must be programmed with the target
object. While the targeted user port is an obvious candidate, the
DSA links must also be programmed, as well as the CPU port for VLANs.
While at it, also remove local variables that are only used once.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call the .port_enable and .port_disable functions for all ports,
not only the user ports, so that drivers may optimize the power
consumption of all ports after a successful setup.
Unused ports are now disabled on setup. CPU and DSA ports are now
enabled on setup and disabled on teardown. User ports were already
enabled at slave creation and disabled at slave destruction.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is currently difficult to read the different steps involved in the
setup and teardown of ports in the DSA code. Keep it simple with a
single switch statement for each port type: UNUSED, CPU, DSA, or USER.
Also no need to call devlink_port_unregister from within dsa_port_setup
as this step is inconditionally handled by dsa_port_teardown on error.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supported PHY features are either auto-detected or explicitly set.
In both cases calling genphy_config_init isn't needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RX timestamping is enabled and two link-local (non-meta) frames are
received in a row, this constitutes an error.
The tagger is always caching the last link-local frame, in an attempt to
merge it with the meta follow-up frame when that arrives. To recover
from the above error condition, the initial cached link-local frame is
dropped and the second frame in a row is cached (in expectance of the
second meta frame).
However, when dropping the initial link-local frame, its backing memory
was being leaked.
Fixes: f3097be21b ("net: dsa: sja1105: Add a state machine for RX timestamping")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a meta frame is received, it is associated with the cached
sp->data->stampable_skb from the DSA tagger private structure.
Cached means its refcount is incremented with skb_get() in order for
dsa_switch_rcv() to not free it when the tagger .rcv returns NULL.
The mistake is that skb_unref() is not the correct function to use. It
will correctly decrement the refcount (which will go back to zero) but
the skb memory will not be freed. That is the job of kfree_skb(), which
also calls skb_unref().
But it turns out that freeing the cached stampable_skb is in fact not
necessary. It is still a perfectly valid skb, and now it is even
annotated with the partial RX timestamp. So remove the skb_copy()
altogether and simply pass the stampable_skb with a refcount of 1
(incremented by us, decremented by dsa_switch_rcv) up the stack.
Fixes: f3097be21b ("net: dsa: sja1105: Add a state machine for RX timestamping")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the CPU port registers dump into the master interface registers
dump through ethtool, by nesting the ethtool_drvinfo and ethtool_regs
structures of the CPU port into the dump.
drvinfo->regdump_len will contain the full data length, while regs->len
will contain only the master interface registers dump length.
This allows for example to dump the CPU port registers on a ZII Dev
C board like this:
# ethtool -d eth1
0x004: 0x00000000
0x008: 0x0a8000aa
0x010: 0x01000000
0x014: 0x00000000
0x024: 0xf0000102
0x040: 0x6d82c800
0x044: 0x00000020
0x064: 0x40000000
0x084: RCR (Receive Control Register) 0x47c00104
MAX_FL (Maximum frame length) 1984
FCE (Flow control enable) 0
BC_REJ (Broadcast frame reject) 0
PROM (Promiscuous mode) 0
DRT (Disable receive on transmit) 0
LOOP (Internal loopback) 0
0x0c4: TCR (Transmit Control Register) 0x00000004
RFC_PAUSE (Receive frame control pause) 0
TFC_PAUSE (Transmit frame control pause) 0
FDEN (Full duplex enable) 1
HBC (Heartbeat control) 0
GTS (Graceful transmit stop) 0
0x0e4: 0x76735d6d
0x0e8: 0x7e9e8808
0x0ec: 0x00010000
.
.
.
88E6352 Switch Port Registers
------------------------------
00: Port Status 0x4d04
Pause Enabled 0
My Pause 1
802.3 PHY Detected 0
Link Status Up
Duplex Full
Speed 100 or 200 Mbps
EEE Enabled 0
Transmitter Paused 0
Flow Control 0
Config Mode 0x4
01: Physical Control 0x003d
RGMII Receive Timing Control Default
RGMII Transmit Timing Control Default
200 BASE Mode 100
Flow Control's Forced value 0
Force Flow Control 0
Link's Forced value Up
Force Link 1
Duplex's Forced value Full
Force Duplex 1
Force Speed 100 or 200 Mbps
.
.
.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This Kconfig option is unused, drop it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DSA tag code for Microchip KSZ8795 switch. The switch is simpler
and the tag is only 1 byte, instead of 2 as is the case with KSZ9477.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This object stores the flow block callbacks that are attached to this
block. Update flow_block_cb_lookup() to take this new object.
This patch restores the block sharing feature.
Fixes: da3eeb904f ("net: flow_offload: add list handling functions")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename this type definition and adapt users.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to annotate the netns on the flow block callback object,
flow_block_cb_is_busy() already checks for used blocks.
Fixes: d63db30c85 ("net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing unlock before return from function sk_buff()
in the error handling case.
Fixes: f3097be21b ("net: dsa: sja1105: Add a state machine for RX timestamping")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for enabling or disabling the flooding of
unknown multicast traffic on the CPU ports, depending on the value
of the switchdev SWITCHDEV_ATTR_ID_BRIDGE_MROUTER attribute.
The current behavior is kept unchanged but a user can now prevent
the CPU conduit to be flooded with a lot of unregistered traffic that
the network stack needs to filter in software with e.g.:
echo 0 > /sys/class/net/br0/multicast_router
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a function to check if flow block callback is already in
use. Call this new function from flow_block_cb_setup_simple() and from
drivers.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates flow_block_cb_setup_simple() to use the flow block API.
Several drivers are also adjusted to use it.
This patch introduces the per-driver list of flow blocks to account for
blocks that are already in use.
Remove tc_block_offload alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename from TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_* and
remove temporary tcf_block_binder_type alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename from TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND and remove
temporary tc_block_command alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the dsa_slave_switchdev_port_{attr_set,obj}_event functions
in favor of the switchdev_handle_port_{attr_set,obj_add,obj_del}
helpers which recurse into the lower devices of the target interface.
This has the benefit of being aware of the operations made on the
bridge device itself, where orig_dev is the bridge, and dev is the
slave. This can be used later to configure the hardware switches.
Only VLAN and (port) MDB objects not directly targeting the slave
device are unsupported at the moment, so skip this case in their
respective case statements.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switchdev handle helpers make use of a device checking helper
requiring a const net_device. Make dsa_slave_dev_check compliant
to this.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current DSA code handling switchdev objects does not recurse into
the lower devices thus is never called with an orig_dev member being
a bridge device, hence remove this useless check.
At the same time, remove the comments about the callers, which is
unlikely to be updated if the code changes and thus will be confusing.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packing facility is needed to decode Ethernet meta frames containing
source port and RX timestamping information.
The DSA driver selects CONFIG_PACKING, but the tagger did not, and since
taggers can be now compiled as modules independently from the drivers
themselves, this is an issue now, as CONFIG_PACKING is disabled by
default on all architectures.
Fixes: e53e18a6fe ("net: dsa: sja1105: Receive and decode meta frames")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to specifically deal with phylink_of_phy_connect() returning
-ENODEV, because this can happen when a CPU/DSA port does connect
neither to a PHY, nor has a fixed-link property. This is a valid use
case that is permitted by the binding and indicates to the switch:
auto-configure port with maximum capabilities.
Fixes: 0e27921816 ("net: dsa: Use PHYLINK for the CPU/DSA ports")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Meta frame reception relies on the hardware keeping its promise that it
will send no other traffic towards the CPU port between a link-local
frame and a meta frame. Otherwise there is no other way to associate
the meta frame with the link-local frame it's holding a timestamp of.
The receive function is made stateful, and buffers a timestampable frame
until its meta frame arrives, then merges the two, drops the meta and
releases the link-local frame up the stack.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support in the tagger for understanding the source port and
switch id of meta frames. Their timestamp is also extracted but not
used yet - this needs to be done in a state machine that modifies the
previously received timestampable frame - will be added in a follow-up
patch.
Also take the opportunity to:
- Remove a comment in sja1105_filter made obsolete by e8d67fa569
("net: dsa: sja1105: Don't store frame type in skb->cb")
- Reorder the checks in sja1105_filter to optimize for the most likely
scenario first: regular traffic.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although meta frames are configured to be sent at SJA1105_META_DMAC
(01-80-C2-00-00-0E) which is a multicast MAC address that would also be
trapped by the switch to the CPU, were it to receive it on a front-panel
port, meta frames are conceptually not link-local frames, they only
carry their RX timestamps.
The choice of sending meta frames at a multicast DMAC is a pragmatic
one, to avoid installing an extra entry to the DSA master port's
multicast MAC filter.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Meta frames are sent on the CPU port by the switch if RX timestamping is
enabled. They contain a partial timestamp of the previous frame.
They are Ethernet frames with the Ethernet header constructed out of:
- SJA1105_META_DMAC
- SJA1105_META_SMAC
- ETH_P_SJA1105_META
The Ethernet payload will be decoded in a follow-up patch.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The incl_srcpt setting makes the switch mangle the destination MACs of
multicast frames trapped to the CPU - a primitive tagging mechanism that
works even when we cannot use the 802.1Q software features.
The downside is that the two multicast MAC addresses that the switch
traps for L2 PTP (01-80-C2-00-00-0E and 01-1B-19-00-00-00) quickly turn
into a lot more, as the switch encodes the source port and switch id
into bytes 3 and 4 of the MAC. The resulting range of MAC addresses
would need to be installed manually into the DSA master port's multicast
MAC filter, and even then, most devices might not have a large enough
MAC filtering table.
As a result, only limit use of incl_srcpt to when it's strictly
necessary: when under a VLAN filtering bridge. This fixes PTP in
non-bridged mode (standalone ports). Otherwise, PTP frames, as well as
metadata follow-up frames holding RX timestamps won't be received
because they will be blocked by the master port's MAC filter.
Linuxptp doesn't help, because it only requests the addition of the
unmodified PTP MACs to the multicast filter.
This issue is not seen in bridged mode because the master port is put in
promiscuous mode when the slave ports are enslaved to a bridge.
Therefore, there is no downside to having the incl_srcpt mechanism
active there.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes the existing implementation from tag_sja1105, which was
partially incorrect (it was not changing the MAC header offset, thereby
leaving it to point 4 bytes earlier than it should have).
This overwrites the VLAN tag by moving the Ethernet source and
destination MACs 4 bytes to the right. Then skb->data (assumed to be
pointing immediately after the EtherType) is temporarily pushed to the
beginning of the new Ethernet header, the new Ethernet header offset and
length are recorded, then skb->data is moved back to where it was.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is helpful for e.g. draining per-driver (not per-port) tagger
queues.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For drivers that use deferred_xmit for PTP frames (such as sja1105),
there is no need to perform matching between PTP frames and their egress
timestamps, since the sending process can be serialized.
In that case, it makes sense to have the pointer to the skb clone that
DSA made directly in the skb->cb. It will be used for pushing the egress
timestamp back in the application socket's error queue.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Free AF_PACKET po->rollover properly, from Willem de Bruijn.
2) Read SFP eeprom in max 16 byte increments to avoid problems with
some SFP modules, from Russell King.
3) Fix UDP socket lookup wrt. VRF, from Tim Beale.
4) Handle route invalidation properly in s390 qeth driver, from Julian
Wiedmann.
5) Memory leak on unload in RDS, from Zhu Yanjun.
6) sctp_process_init leak, from Neil HOrman.
7) Fix fib_rules rule insertion semantic change that broke Android,
from Hangbin Liu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
pktgen: do not sleep with the thread lock held.
net: mvpp2: Use strscpy to handle stat strings
net: rds: fix memory leak in rds_ib_flush_mr_pool
ipv6: fix EFAULT on sendto with icmpv6 and hdrincl
ipv6: use READ_ONCE() for inet->hdrincl as in ipv4
Revert "fib_rules: return 0 directly if an exactly same rule exists when NLM_F_EXCL not supplied"
net: aquantia: fix wol configuration not applied sometimes
ethtool: fix potential userspace buffer overflow
Fix memory leak in sctp_process_init
net: rds: fix memory leak when unload rds_rdma
ipv6: fix the check before getting the cookie in rt6_get_cookie
ipv4: not do cache for local delivery if bc_forwarding is enabled
s390/qeth: handle error when updating TX queue count
s390/qeth: fix VLAN attribute in bridge_hostnotify udev event
s390/qeth: check dst entry before use
s390/qeth: handle limited IPv4 broadcast in L3 TX path
net: fix indirect calls helpers for ptype list hooks.
net: ipvlan: Fix ipvlan device tso disabled while NETIF_F_IP_CSUM is set
udp: only choose unbound UDP socket for multicast when not in a VRF
net/tls: replace the sleeping lock around RX resync with a bit lock
...
Due to a confusion I thought that eth_type_trans() was called by the
network stack whereas it can actually be called by network drivers to
figure out the skb protocol and next packet_type handlers.
In light of the above, it is not safe to store the frame type from the
DSA tagger's .filter callback (first entry point on RX path), since GRO
is yet to be invoked on the received traffic. Hence it is very likely
that the skb->cb will actually get overwritten between eth_type_trans()
and the actual DSA packet_type handler.
Of course, what this patch fixes is the actual overwriting of the
SJA1105_SKB_CB(skb)->type field from the GRO layer, which made all
frames be seen as SJA1105_FRAME_TYPE_NORMAL (0).
Fixes: 227d07a07e ("net: dsa: sja1105: Add support for traffic through standalone ports")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is another set of reviewed patches that adds SPDX tags to different
kernel files, based on a set of rules that are being used to parse the
comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review and
analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPCHLg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykxyACgql6ktH+Tv8Ho1747kKPiFca1Jq0AoK5HORXI
yB0DSTXYNjMtH41ypnsZ
=x2f8
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
In case a call to dsa_tree_setup() fails, an attempt to cleanup is made
by calling dsa_tree_remove_switch(), which should take care of
removing/unregistering any resources previously allocated. This does not
happen because it is conditioned by dst->setup being true, which is set
only after _all_ setup steps were performed successfully.
This is especially interesting when the internal MDIO bus is registered
but afterwards, a port setup fails and the mdiobus_unregister() is never
called. This leads to a BUG_ON() complaining about the fact that it's
trying to free an MDIO bus that's still registered.
Add proper error handling in all functions branching from
dsa_tree_setup().
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reported-by: kernel test robot <rong.a.chen@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tools like tcpdump need to be able to decode the significance of fake
VLAN headers that DSA uses to separate switch ports.
But currently these have no global significance - they are simply an
ordered list of DSA_MAX_SWITCHES x DSA_MAX_PORTS numbers ending at 4095.
The reason why this is submitted as a fix is that the existing mapping
of VIDs should not enter into a stable kernel, so we can pretend that
only the new format exists. This way tcpdump won't need to try to make
something out of the VLAN tags on 5.2 kernels.
Fixes: f9bbe4477c ("net: dsa: Optional VLAN-based port separation for switches without tagging")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 802.1Q tagging performs an unbalanced setup in terms of RX VIDs on
the CPU port. For the ingress path of a 802.1Q switch to work, the RX
VID of a port needs to be seen as tagged egress on the CPU port.
While configuring the other front-panel ports to be part of this VID,
for bridge scenarios, the untagged flag is applied even on the CPU port
in dsa_switch_vlan_add. This happens because DSA applies the same flags
on the CPU port as on the (bridge-controlled) slave ports, and the
effect in this case is that the CPU port tagged settings get deleted.
Instead of fixing DSA by introducing a way to control VLAN flags on the
CPU port (and hence stop inheriting from the slave ports) - a hard,
perhaps intractable problem - avoid this situation by moving the setup
part of the RX VID on the CPU port after all the other front-panel ports
have been added to the VID.
Fixes: f9bbe4477c ("net: dsa: Optional VLAN-based port separation for switches without tagging")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For DSA switches that do not have an .adjust_link callback, aka those
who transitioned totally to the PHYLINK-compliant API, use PHYLINK to
drive the CPU/DSA ports.
The PHYLIB usage and .adjust_link are kept but deprecated, and users are
asked to transition from it. The reason why we can't do anything for
them is because PHYLINK does not wrap the fixed-link state behind a
phydev object, so we cannot wrap .phylink_mac_config into .adjust_link
unless we fabricate a phy_device structure.
For these ports, the newly introduced PHYLINK_DEV operation type is
used and the dsa_switch device structure is passed to PHYLINK for
printing purposes. The handling of the PHYLINK_NETDEV and PHYLINK_DEV
PHYLINK instances is common from the perspective of the driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to have a common handling of PHYLINK for the slave and non-user
ports, the DSA core glue logic (between PHYLINK and the driver) must use
an API that does not rely on a struct net_device.
These will also be called by the CPU-port-handling code in a further
patch.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylink_config structure will encapsulate a pointer to a struct
device and the operation type requested for this instance of PHYLINK.
This patch does not make any functional changes, it just transitions the
PHYLINK internals and all its users to the new API.
A pointer to a phylink_config structure will be passed to
phylink_create() instead of the net_device directly. Also, the same
phylink_config pointer will be passed back to all phylink_mac_ops
callbacks instead of the net_device. Using this mechanism, a PHYLINK
user can get the original net_device using a structure such as
'to_net_dev(config->dev)' or directly the structure containing the
phylink_config using a container_of call.
At the moment, only the PHYLINK_NETDEV is defined as a valid operation
type for PHYLINK. In this mode, a valid reference to a struct device
linked to the original net_device should be passed to PHYLINK through
the phylink_config structure.
This API changes is mainly driven by the necessity of adding a new
operation type in PHYLINK that disconnects the phy_device from the
net_device and also works when the net_device is lacking.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sk_buff control block can have any contents on xmit put there by the
stack, so initialization is mandatory, since we are checking its value
after the actual DSA xmit (the tagger may have changed it).
The DSA_SKB_ZERO() macro could have been used for this purpose, but:
- Zeroizing a 48-byte memory region in the hotpath is best avoided.
- It would have triggered a warning with newer compilers since
__dsa_skb_cb contains a structure within a structure, and the {0}
initializer was incorrect for that purpose.
So simply remove the DSA_SKB_ZERO() macro and initialize the
deferred_xmit variable by hand (which should be done for all further
dsa_skb_cb variables which need initialization - currently none - to
avoid the performance penalty).
Fixes: 97a69a0dea ("net: dsa: Add support for deferred xmit")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix gcc build error:
net/dsa/tag_brcm.c:211:16: error: brcm_prepend_netdev_ops undeclared here (not in a function); did you mean brcm_netdev_ops?
DSA_TAG_DRIVER(brcm_prepend_netdev_ops);
^
./include/net/dsa.h:708:10: note: in definition of macro DSA_TAG_DRIVER
.ops = &__ops, \
^~~~~
./include/net/dsa.h:701:36: warning: dsa_tag_driver_brcm_prepend_netdev_ops defined but not used [-Wunused-variable]
#define DSA_TAG_DRIVER_NAME(__ops) dsa_tag_driver ## _ ## __ops
^
./include/net/dsa.h:707:30: note: in expansion of macro DSA_TAG_DRIVER_NAME
static struct dsa_tag_driver DSA_TAG_DRIVER_NAME(__ops) = { \
^~~~~~~~~~~~~~~~~~~
net/dsa/tag_brcm.c:211:1: note: in expansion of macro DSA_TAG_DRIVER
DSA_TAG_DRIVER(brcm_prepend_netdev_ops);
Like the CONFIG_NET_DSA_TAG_BRCM case,
brcm_prepend_netdev_ops and DSA_TAG_PROTO_BRCM_PREPEND
should be wrappeed by CONFIG_NET_DSA_TAG_BRCM_PREPEND.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: b74b70c449 ("net: dsa: Support prepended Broadcom tag")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was NVMEM support added to of_get_mac_address, so it could now
return ERR_PTR encoded error values, so we need to adjust all current
users of of_get_mac_address to this new fact.
While at it, remove superfluous is_valid_ether_addr as the MAC address
returned from of_get_mac_address is always valid and checked by
is_valid_ether_addr anyway.
Fixes: d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support this, we are creating a make-shift switch tag out of
a VLAN trunk configured on the CPU port. Termination of normal traffic
on switch ports only works when not under a vlan_filtering bridge.
Termination of management (PTP, BPDU) traffic works under all
circumstances because it uses a different tagging mechanism
(incl_srcpt). We are making use of the generic CONFIG_NET_DSA_TAG_8021Q
code and leveraging it from our own CONFIG_NET_DSA_TAG_SJA1105.
There are two types of traffic: regular and link-local.
The link-local traffic received on the CPU port is trapped from the
switch's regular forwarding decisions because it matched one of the two
DMAC filters for management traffic.
On transmission, the switch requires special massaging for these
link-local frames. Due to a weird implementation of the switching IP, by
default it drops link-local frames that originate on the CPU port.
It needs to be told where to forward them to, through an SPI command
("management route") that is valid for only a single frame.
So when we're sending link-local traffic, we are using the
dsa_defer_xmit mechanism.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some hardware needs to take work to get convinced to receive frames on
the CPU port (such as the sja1105 which takes temporary L2 forwarding
rules over SPI that last for a single frame). Such work needs a
sleepable context, and because the regular .ndo_start_xmit is atomic,
this cannot be done in the tagger. So introduce a generic DSA mechanism
that sets up a transmit skb queue and a workqueue for deferred
transmission.
The new driver callback (.port_deferred_xmit) is in dsa_switch and not
in the tagger because the operations that require sleeping typically
also involve interacting with the hardware, and not simply skb
manipulations. Therefore having it there simplifies the structure a bit
and makes it unnecessary to export functions from the driver to the
tagger.
The driver is responsible of calling dsa_enqueue_skb which transfers it
to the master netdevice. This is so that it has a chance of performing
some more work afterwards, such as cleanup or TX timestamping.
To tell DSA that skb xmit deferral is required, I have thought about
changing the return type of the tagger .xmit from struct sk_buff * into
a enum dsa_tx_t that could potentially encode a DSA_XMIT_DEFER value.
But the trailer tagger is reallocating every skb on xmit and therefore
making a valid use of the pointer return value. So instead of reworking
the API in complicated ways, right now a boolean property in the newly
introduced DSA_SKB_CB is set.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frames get processed by DSA and redirected to switch port net devices
based on the ETH_P_XDSA multiplexed packet_type handler found by the
network stack when calling eth_type_trans().
The running assumption is that once the DSA .rcv function is called, DSA
is always able to decode the switch tag in order to change the skb->dev
from its master.
However there are tagging protocols (such as the new DSA_TAG_PROTO_SJA1105,
user of DSA_TAG_PROTO_8021Q) where this assumption is not completely
true, since switch tagging piggybacks on the absence of a vlan_filtering
bridge. Moreover, management traffic (BPDU, PTP) for this switch doesn't
rely on switch tagging, but on a different mechanism. So it would make
sense to at least be able to terminate that.
Having DSA receive traffic it can't decode would put it in an impossible
situation: the eth_type_trans() function would invoke the DSA .rcv(),
which could not change skb->dev, then eth_type_trans() would be invoked
again, which again would call the DSA .rcv, and the packet would never
be able to exit the DSA filter and would spiral in a loop until the
whole system dies.
This happens because eth_type_trans() doesn't actually look at the skb
(so as to identify a potential tag) when it deems it as being
ETH_P_XDSA. It just checks whether skb->dev has a DSA private pointer
installed (therefore it's a DSA master) and that there exists a .rcv
callback (everybody except DSA_TAG_PROTO_NONE has that). This is
understandable as there are many switch tags out there, and exhaustively
checking for all of them is far from ideal.
The solution lies in introducing a filtering function for each tagging
protocol. In the absence of a filtering function, all traffic is passed
to the .rcv DSA callback. The tagging protocol should see the filtering
function as a pre-validation that it can decode the incoming skb. The
traffic that doesn't match the filter will bypass the DSA .rcv callback
and be left on the master netdevice, which wasn't previously possible.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides generic DSA code for using VLAN (802.1Q) tags for
the same purpose as a dedicated switch tag for injection/extraction.
It is based on the discussions and interest that has been so far
expressed in https://www.spinics.net/lists/netdev/msg556125.html.
Unlike all other DSA-supported tagging protocols, CONFIG_NET_DSA_TAG_8021Q
does not offer a complete solution for drivers (nor can it). Instead, it
provides generic code that driver can opt into calling:
- dsa_8021q_xmit: Inserts a VLAN header with the specified contents.
Can be called from another tagging protocol's xmit function.
Currently the LAN9303 driver is inserting headers that are simply
802.1Q with custom fields, so this is an opportunity for code reuse.
- dsa_8021q_rcv: Retrieves the TPID and TCI from a VLAN-tagged skb.
Removing the VLAN header is left as a decision for the caller to make.
- dsa_port_setup_8021q_tagging: For each user port, installs an Rx VID
and a Tx VID, for proper untagged traffic identification on ingress
and steering on egress. Also sets up the VLAN trunk on the upstream
(CPU or DSA) port. Drivers are intentionally left to call this
function explicitly, depending on the context and hardware support.
The expected switch behavior and VLAN semantics should not be violated
under any conditions. That is, after calling
dsa_port_setup_8021q_tagging, the hardware should still pass all
ingress traffic, be it tagged or untagged.
For uniformity with the other tagging protocols, a module for the
dsa_8021q_netdev_ops structure is registered, but the typical usage is
to set up another tagging protocol which selects CONFIG_NET_DSA_TAG_8021Q,
and calls the API from tag_8021q.h. Null function definitions are also
provided so that a "depends on" is not forced in the Kconfig.
This tagging protocol only works when switch ports are standalone, or
when they are added to a VLAN-unaware bridge. It will probably remain
this way for the reasons below.
When added to a bridge that has vlan_filtering 1, the bridge core will
install its own VLANs and reset the pvids through switchdev. For the
bridge core, switchdev is a write-only pipe. All VLAN-related state is
kept in the bridge core and nothing is read from DSA/switchdev or from
the driver. So the bridge core will break this port separation because
it will install the vlan_default_pvid into all switchdev ports.
Even if we could teach the bridge driver about switchdev preference of a
certain vlan_default_pvid (task difficult in itself since the current
setting is per-bridge but we would need it per-port), there would still
exist many other challenges.
Firstly, in the DSA rcv callback, a driver would have to perform an
iterative reverse lookup to find the correct switch port. That is
because the port is a bridge slave, so its Rx VID (port PVID) is subject
to user configuration. How would we ensure that the user doesn't reset
the pvid to a different value (which would make an O(1) translation
impossible), or to a non-unique value within this DSA switch tree (which
would make any translation impossible)?
Finally, not all switch ports are equal in DSA, and that makes it
difficult for the bridge to be completely aware of this anyway.
The CPU port needs to transmit tagged packets (VLAN trunk) in order for
the DSA rcv code to be able to decode source information.
But the bridge code has absolutely no idea which switch port is the CPU
port, if nothing else then just because there is no netdevice registered
by DSA for the CPU port.
Also DSA does not currently allow the user to specify that they want the
CPU port to do VLAN trunking anyway. VLANs are added to the CPU port
using the same flags as they were added on the user port.
So the VLANs installed by dsa_port_setup_8021q_tagging per driver
request should remain private from the bridge's and user's perspective,
and should not alter the VLAN semantics observed by the user.
In the current implementation a VLAN range ending at 4095 (VLAN_N_VID)
is reserved for this purpose. Each port receives a unique Rx VLAN and a
unique Tx VLAN. Separate VLANs are needed for Rx and Tx because they
serve different purposes: on Rx the switch must process traffic as
untagged and process it with a port-based VLAN, but with care not to
hinder bridging. On the other hand, the Tx VLAN is where the
reachability restrictions are imposed, since by tagging frames in the
xmit callback we are telling the switch onto which port to steer the
frame.
Some general guidance on how this support might be employed for
real-life hardware (some comments made by Florian Fainelli):
- If the hardware supports VLAN tag stacking, it should somehow back
up its private VLAN settings when the bridge tries to override them.
Then the driver could re-apply them as outer tags. Dedicating an outer
tag per bridge device would allow identical inner tag VID numbers to
co-exist, yet preserve broadcast domain isolation.
- If the switch cannot handle VLAN tag stacking, it should disable this
port separation when added as slave to a vlan_filtering bridge, in
that case having reduced functionality.
- Drivers for old switches that don't support the entire VLAN_N_VID
range will need to rework the current range selection mechanism.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed so that the newly introduced tag_8021q may access these
core DSA functions when built as a module.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows the driver to perform some manipulations of its own during
setup, using generic switchdev calls. Having the notifiers registered at
setup time is important because otherwise any switchdev transaction
emitted during this time would be ignored (dispatched to an empty call
chain).
One current usage scenario is for the driver to request DSA to set up
802.1Q based switch tagging for its ports.
There is no danger for the driver setup code to start racing now with
switchdev events emitted from the network stack (such as bridge core)
even if the notifier is registered earlier. This is because the network
stack needs a net_device as a vehicle to perform switchdev operations,
and the slave net_devices are registered later than the core driver
setup anyway (ds->ops->setup in dsa_switch_setup vs dsa_port_setup).
Luckily DSA doesn't need a net_device to carry out switchdev callbacks,
and therefore drivers shouldn't assume either that net_devices are
available at the time their switchdev callbacks get invoked.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>-
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates dsa hardware switch handling infrastructure to use the newer
intermediate representation for flow actions in matchall offloads.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all drivers can be probed using more traditional methods,
remove the legacy probe code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This hides the need to perform a two-phase transaction and construct a
switchdev_obj_port_vlan struct.
Call graph (including a function that will be introduced in a follow-up
patch) looks like this now (same for the *_vlan_del function):
dsa_slave_vlan_rx_add_vid dsa_port_setup_8021q_tagging
| |
| |
| +-------------+
| |
v v
dsa_port_vid_add dsa_slave_port_obj_add
| |
+-------+ +-------+
| |
v v
dsa_port_vlan_add
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if VLAN filtering is global, DSA will call this callback once per
each port. Drivers should not have to compare the global state with the
requested change. So let DSA do it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current behavior is not as obvious as one would assume (which is
that, if the driver set vlan_filtering_is_global = 1, then checking any
dp->vlan_filtering would yield the same result). Only the ports which
are actively enslaved into a bridge would have vlan_filtering set.
This makes it tricky for drivers to check what the global state is.
So fix this and make the struct dsa_switch hold this global setting.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ports are standalone (after they left the bridge), they should have
no VLAN filtering semantics (they should pass all traffic to the CPU).
Currently this is not true for switchdev drivers, because the bridge
"forgets" to unset that.
Normally one would think that doing this at the bridge layer would be a
better idea, i.e. call br_vlan_filter_toggle() from br_del_if(), similar
to how nbp_vlan_init() is called from br_add_if().
However what complicates that approach, and makes this one preferable,
is the fact that for the bridge core, vlan_filtering is a per-bridge
setting, whereas for switchdev/DSA it is per-port. Also there are
switches where the setting is per the entire device, and unsetting
vlan_filtering one by one, for each leaving port, would not be possible
from the bridge core without a certain level of awareness. So do this in
DSA and let drivers be unaware of it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some switches, the action of whether to parse VLAN frame headers and use
that information for ingress admission is configurable, but not per
port. Such is the case for the Broadcom BCM53xx and the NXP SJA1105
families, for example. In that case, DSA can prevent the bridge core
from trying to apply different VLAN filtering settings on net devices
that belong to the same switch.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows drivers to query the VLAN setting imposed by the bridge
driver directly from DSA, instead of keeping their own state based on
the .port_vlan_filtering callback.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the CONFIG symbols tristate and add help text.
The broadcom and Microchip KSZ tag drivers support two different
tagging protocols in one driver. Add a configuration option for the
drivers, and then options to select the protocol.
Create a submenu for the tagging drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
tab/space cleanup
Help text wording
NET_DSA_TAG_BRCM_COMMON and NET_DSA_TAG_KZS_COMMON hidden
v3:
More tabification
Punctuation
v4:
trailler->trailer
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that the driver is compiled with both
CONFIG_NET_DSA_TAG_BRCM and CONFIG_NET_DSA_TAG_BRCM_PREPEND disabled.
This results in warnings about unused symbols. Add some conditional
compilation to avoid this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2
Reorder patch to before tag drivers can be modules
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that tag drivers dynamically register, we don't need the static
table. Remove it. This also means the tag driver structures can be
made static.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean