Rename from TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND and remove
temporary tc_block_command alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the dsa_slave_switchdev_port_{attr_set,obj}_event functions
in favor of the switchdev_handle_port_{attr_set,obj_add,obj_del}
helpers which recurse into the lower devices of the target interface.
This has the benefit of being aware of the operations made on the
bridge device itself, where orig_dev is the bridge, and dev is the
slave. This can be used later to configure the hardware switches.
Only VLAN and (port) MDB objects not directly targeting the slave
device are unsupported at the moment, so skip this case in their
respective case statements.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switchdev handle helpers make use of a device checking helper
requiring a const net_device. Make dsa_slave_dev_check compliant
to this.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current DSA code handling switchdev objects does not recurse into
the lower devices thus is never called with an orig_dev member being
a bridge device, hence remove this useless check.
At the same time, remove the comments about the callers, which is
unlikely to be updated if the code changes and thus will be confusing.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packing facility is needed to decode Ethernet meta frames containing
source port and RX timestamping information.
The DSA driver selects CONFIG_PACKING, but the tagger did not, and since
taggers can be now compiled as modules independently from the drivers
themselves, this is an issue now, as CONFIG_PACKING is disabled by
default on all architectures.
Fixes: e53e18a6fe ("net: dsa: sja1105: Receive and decode meta frames")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to specifically deal with phylink_of_phy_connect() returning
-ENODEV, because this can happen when a CPU/DSA port does connect
neither to a PHY, nor has a fixed-link property. This is a valid use
case that is permitted by the binding and indicates to the switch:
auto-configure port with maximum capabilities.
Fixes: 0e27921816 ("net: dsa: Use PHYLINK for the CPU/DSA ports")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Meta frame reception relies on the hardware keeping its promise that it
will send no other traffic towards the CPU port between a link-local
frame and a meta frame. Otherwise there is no other way to associate
the meta frame with the link-local frame it's holding a timestamp of.
The receive function is made stateful, and buffers a timestampable frame
until its meta frame arrives, then merges the two, drops the meta and
releases the link-local frame up the stack.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support in the tagger for understanding the source port and
switch id of meta frames. Their timestamp is also extracted but not
used yet - this needs to be done in a state machine that modifies the
previously received timestampable frame - will be added in a follow-up
patch.
Also take the opportunity to:
- Remove a comment in sja1105_filter made obsolete by e8d67fa569
("net: dsa: sja1105: Don't store frame type in skb->cb")
- Reorder the checks in sja1105_filter to optimize for the most likely
scenario first: regular traffic.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although meta frames are configured to be sent at SJA1105_META_DMAC
(01-80-C2-00-00-0E) which is a multicast MAC address that would also be
trapped by the switch to the CPU, were it to receive it on a front-panel
port, meta frames are conceptually not link-local frames, they only
carry their RX timestamps.
The choice of sending meta frames at a multicast DMAC is a pragmatic
one, to avoid installing an extra entry to the DSA master port's
multicast MAC filter.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Meta frames are sent on the CPU port by the switch if RX timestamping is
enabled. They contain a partial timestamp of the previous frame.
They are Ethernet frames with the Ethernet header constructed out of:
- SJA1105_META_DMAC
- SJA1105_META_SMAC
- ETH_P_SJA1105_META
The Ethernet payload will be decoded in a follow-up patch.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The incl_srcpt setting makes the switch mangle the destination MACs of
multicast frames trapped to the CPU - a primitive tagging mechanism that
works even when we cannot use the 802.1Q software features.
The downside is that the two multicast MAC addresses that the switch
traps for L2 PTP (01-80-C2-00-00-0E and 01-1B-19-00-00-00) quickly turn
into a lot more, as the switch encodes the source port and switch id
into bytes 3 and 4 of the MAC. The resulting range of MAC addresses
would need to be installed manually into the DSA master port's multicast
MAC filter, and even then, most devices might not have a large enough
MAC filtering table.
As a result, only limit use of incl_srcpt to when it's strictly
necessary: when under a VLAN filtering bridge. This fixes PTP in
non-bridged mode (standalone ports). Otherwise, PTP frames, as well as
metadata follow-up frames holding RX timestamps won't be received
because they will be blocked by the master port's MAC filter.
Linuxptp doesn't help, because it only requests the addition of the
unmodified PTP MACs to the multicast filter.
This issue is not seen in bridged mode because the master port is put in
promiscuous mode when the slave ports are enslaved to a bridge.
Therefore, there is no downside to having the incl_srcpt mechanism
active there.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes the existing implementation from tag_sja1105, which was
partially incorrect (it was not changing the MAC header offset, thereby
leaving it to point 4 bytes earlier than it should have).
This overwrites the VLAN tag by moving the Ethernet source and
destination MACs 4 bytes to the right. Then skb->data (assumed to be
pointing immediately after the EtherType) is temporarily pushed to the
beginning of the new Ethernet header, the new Ethernet header offset and
length are recorded, then skb->data is moved back to where it was.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is helpful for e.g. draining per-driver (not per-port) tagger
queues.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For drivers that use deferred_xmit for PTP frames (such as sja1105),
there is no need to perform matching between PTP frames and their egress
timestamps, since the sending process can be serialized.
In that case, it makes sense to have the pointer to the skb clone that
DSA made directly in the skb->cb. It will be used for pushing the egress
timestamp back in the application socket's error queue.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Free AF_PACKET po->rollover properly, from Willem de Bruijn.
2) Read SFP eeprom in max 16 byte increments to avoid problems with
some SFP modules, from Russell King.
3) Fix UDP socket lookup wrt. VRF, from Tim Beale.
4) Handle route invalidation properly in s390 qeth driver, from Julian
Wiedmann.
5) Memory leak on unload in RDS, from Zhu Yanjun.
6) sctp_process_init leak, from Neil HOrman.
7) Fix fib_rules rule insertion semantic change that broke Android,
from Hangbin Liu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
pktgen: do not sleep with the thread lock held.
net: mvpp2: Use strscpy to handle stat strings
net: rds: fix memory leak in rds_ib_flush_mr_pool
ipv6: fix EFAULT on sendto with icmpv6 and hdrincl
ipv6: use READ_ONCE() for inet->hdrincl as in ipv4
Revert "fib_rules: return 0 directly if an exactly same rule exists when NLM_F_EXCL not supplied"
net: aquantia: fix wol configuration not applied sometimes
ethtool: fix potential userspace buffer overflow
Fix memory leak in sctp_process_init
net: rds: fix memory leak when unload rds_rdma
ipv6: fix the check before getting the cookie in rt6_get_cookie
ipv4: not do cache for local delivery if bc_forwarding is enabled
s390/qeth: handle error when updating TX queue count
s390/qeth: fix VLAN attribute in bridge_hostnotify udev event
s390/qeth: check dst entry before use
s390/qeth: handle limited IPv4 broadcast in L3 TX path
net: fix indirect calls helpers for ptype list hooks.
net: ipvlan: Fix ipvlan device tso disabled while NETIF_F_IP_CSUM is set
udp: only choose unbound UDP socket for multicast when not in a VRF
net/tls: replace the sleeping lock around RX resync with a bit lock
...
Due to a confusion I thought that eth_type_trans() was called by the
network stack whereas it can actually be called by network drivers to
figure out the skb protocol and next packet_type handlers.
In light of the above, it is not safe to store the frame type from the
DSA tagger's .filter callback (first entry point on RX path), since GRO
is yet to be invoked on the received traffic. Hence it is very likely
that the skb->cb will actually get overwritten between eth_type_trans()
and the actual DSA packet_type handler.
Of course, what this patch fixes is the actual overwriting of the
SJA1105_SKB_CB(skb)->type field from the GRO layer, which made all
frames be seen as SJA1105_FRAME_TYPE_NORMAL (0).
Fixes: 227d07a07e ("net: dsa: sja1105: Add support for traffic through standalone ports")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is another set of reviewed patches that adds SPDX tags to different
kernel files, based on a set of rules that are being used to parse the
comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review and
analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPCHLg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykxyACgql6ktH+Tv8Ho1747kKPiFca1Jq0AoK5HORXI
yB0DSTXYNjMtH41ypnsZ
=x2f8
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
In case a call to dsa_tree_setup() fails, an attempt to cleanup is made
by calling dsa_tree_remove_switch(), which should take care of
removing/unregistering any resources previously allocated. This does not
happen because it is conditioned by dst->setup being true, which is set
only after _all_ setup steps were performed successfully.
This is especially interesting when the internal MDIO bus is registered
but afterwards, a port setup fails and the mdiobus_unregister() is never
called. This leads to a BUG_ON() complaining about the fact that it's
trying to free an MDIO bus that's still registered.
Add proper error handling in all functions branching from
dsa_tree_setup().
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reported-by: kernel test robot <rong.a.chen@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tools like tcpdump need to be able to decode the significance of fake
VLAN headers that DSA uses to separate switch ports.
But currently these have no global significance - they are simply an
ordered list of DSA_MAX_SWITCHES x DSA_MAX_PORTS numbers ending at 4095.
The reason why this is submitted as a fix is that the existing mapping
of VIDs should not enter into a stable kernel, so we can pretend that
only the new format exists. This way tcpdump won't need to try to make
something out of the VLAN tags on 5.2 kernels.
Fixes: f9bbe4477c ("net: dsa: Optional VLAN-based port separation for switches without tagging")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 802.1Q tagging performs an unbalanced setup in terms of RX VIDs on
the CPU port. For the ingress path of a 802.1Q switch to work, the RX
VID of a port needs to be seen as tagged egress on the CPU port.
While configuring the other front-panel ports to be part of this VID,
for bridge scenarios, the untagged flag is applied even on the CPU port
in dsa_switch_vlan_add. This happens because DSA applies the same flags
on the CPU port as on the (bridge-controlled) slave ports, and the
effect in this case is that the CPU port tagged settings get deleted.
Instead of fixing DSA by introducing a way to control VLAN flags on the
CPU port (and hence stop inheriting from the slave ports) - a hard,
perhaps intractable problem - avoid this situation by moving the setup
part of the RX VID on the CPU port after all the other front-panel ports
have been added to the VID.
Fixes: f9bbe4477c ("net: dsa: Optional VLAN-based port separation for switches without tagging")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For DSA switches that do not have an .adjust_link callback, aka those
who transitioned totally to the PHYLINK-compliant API, use PHYLINK to
drive the CPU/DSA ports.
The PHYLIB usage and .adjust_link are kept but deprecated, and users are
asked to transition from it. The reason why we can't do anything for
them is because PHYLINK does not wrap the fixed-link state behind a
phydev object, so we cannot wrap .phylink_mac_config into .adjust_link
unless we fabricate a phy_device structure.
For these ports, the newly introduced PHYLINK_DEV operation type is
used and the dsa_switch device structure is passed to PHYLINK for
printing purposes. The handling of the PHYLINK_NETDEV and PHYLINK_DEV
PHYLINK instances is common from the perspective of the driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to have a common handling of PHYLINK for the slave and non-user
ports, the DSA core glue logic (between PHYLINK and the driver) must use
an API that does not rely on a struct net_device.
These will also be called by the CPU-port-handling code in a further
patch.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylink_config structure will encapsulate a pointer to a struct
device and the operation type requested for this instance of PHYLINK.
This patch does not make any functional changes, it just transitions the
PHYLINK internals and all its users to the new API.
A pointer to a phylink_config structure will be passed to
phylink_create() instead of the net_device directly. Also, the same
phylink_config pointer will be passed back to all phylink_mac_ops
callbacks instead of the net_device. Using this mechanism, a PHYLINK
user can get the original net_device using a structure such as
'to_net_dev(config->dev)' or directly the structure containing the
phylink_config using a container_of call.
At the moment, only the PHYLINK_NETDEV is defined as a valid operation
type for PHYLINK. In this mode, a valid reference to a struct device
linked to the original net_device should be passed to PHYLINK through
the phylink_config structure.
This API changes is mainly driven by the necessity of adding a new
operation type in PHYLINK that disconnects the phy_device from the
net_device and also works when the net_device is lacking.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sk_buff control block can have any contents on xmit put there by the
stack, so initialization is mandatory, since we are checking its value
after the actual DSA xmit (the tagger may have changed it).
The DSA_SKB_ZERO() macro could have been used for this purpose, but:
- Zeroizing a 48-byte memory region in the hotpath is best avoided.
- It would have triggered a warning with newer compilers since
__dsa_skb_cb contains a structure within a structure, and the {0}
initializer was incorrect for that purpose.
So simply remove the DSA_SKB_ZERO() macro and initialize the
deferred_xmit variable by hand (which should be done for all further
dsa_skb_cb variables which need initialization - currently none - to
avoid the performance penalty).
Fixes: 97a69a0dea ("net: dsa: Add support for deferred xmit")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix gcc build error:
net/dsa/tag_brcm.c:211:16: error: brcm_prepend_netdev_ops undeclared here (not in a function); did you mean brcm_netdev_ops?
DSA_TAG_DRIVER(brcm_prepend_netdev_ops);
^
./include/net/dsa.h:708:10: note: in definition of macro DSA_TAG_DRIVER
.ops = &__ops, \
^~~~~
./include/net/dsa.h:701:36: warning: dsa_tag_driver_brcm_prepend_netdev_ops defined but not used [-Wunused-variable]
#define DSA_TAG_DRIVER_NAME(__ops) dsa_tag_driver ## _ ## __ops
^
./include/net/dsa.h:707:30: note: in expansion of macro DSA_TAG_DRIVER_NAME
static struct dsa_tag_driver DSA_TAG_DRIVER_NAME(__ops) = { \
^~~~~~~~~~~~~~~~~~~
net/dsa/tag_brcm.c:211:1: note: in expansion of macro DSA_TAG_DRIVER
DSA_TAG_DRIVER(brcm_prepend_netdev_ops);
Like the CONFIG_NET_DSA_TAG_BRCM case,
brcm_prepend_netdev_ops and DSA_TAG_PROTO_BRCM_PREPEND
should be wrappeed by CONFIG_NET_DSA_TAG_BRCM_PREPEND.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: b74b70c449 ("net: dsa: Support prepended Broadcom tag")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was NVMEM support added to of_get_mac_address, so it could now
return ERR_PTR encoded error values, so we need to adjust all current
users of of_get_mac_address to this new fact.
While at it, remove superfluous is_valid_ether_addr as the MAC address
returned from of_get_mac_address is always valid and checked by
is_valid_ether_addr anyway.
Fixes: d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support this, we are creating a make-shift switch tag out of
a VLAN trunk configured on the CPU port. Termination of normal traffic
on switch ports only works when not under a vlan_filtering bridge.
Termination of management (PTP, BPDU) traffic works under all
circumstances because it uses a different tagging mechanism
(incl_srcpt). We are making use of the generic CONFIG_NET_DSA_TAG_8021Q
code and leveraging it from our own CONFIG_NET_DSA_TAG_SJA1105.
There are two types of traffic: regular and link-local.
The link-local traffic received on the CPU port is trapped from the
switch's regular forwarding decisions because it matched one of the two
DMAC filters for management traffic.
On transmission, the switch requires special massaging for these
link-local frames. Due to a weird implementation of the switching IP, by
default it drops link-local frames that originate on the CPU port.
It needs to be told where to forward them to, through an SPI command
("management route") that is valid for only a single frame.
So when we're sending link-local traffic, we are using the
dsa_defer_xmit mechanism.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some hardware needs to take work to get convinced to receive frames on
the CPU port (such as the sja1105 which takes temporary L2 forwarding
rules over SPI that last for a single frame). Such work needs a
sleepable context, and because the regular .ndo_start_xmit is atomic,
this cannot be done in the tagger. So introduce a generic DSA mechanism
that sets up a transmit skb queue and a workqueue for deferred
transmission.
The new driver callback (.port_deferred_xmit) is in dsa_switch and not
in the tagger because the operations that require sleeping typically
also involve interacting with the hardware, and not simply skb
manipulations. Therefore having it there simplifies the structure a bit
and makes it unnecessary to export functions from the driver to the
tagger.
The driver is responsible of calling dsa_enqueue_skb which transfers it
to the master netdevice. This is so that it has a chance of performing
some more work afterwards, such as cleanup or TX timestamping.
To tell DSA that skb xmit deferral is required, I have thought about
changing the return type of the tagger .xmit from struct sk_buff * into
a enum dsa_tx_t that could potentially encode a DSA_XMIT_DEFER value.
But the trailer tagger is reallocating every skb on xmit and therefore
making a valid use of the pointer return value. So instead of reworking
the API in complicated ways, right now a boolean property in the newly
introduced DSA_SKB_CB is set.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frames get processed by DSA and redirected to switch port net devices
based on the ETH_P_XDSA multiplexed packet_type handler found by the
network stack when calling eth_type_trans().
The running assumption is that once the DSA .rcv function is called, DSA
is always able to decode the switch tag in order to change the skb->dev
from its master.
However there are tagging protocols (such as the new DSA_TAG_PROTO_SJA1105,
user of DSA_TAG_PROTO_8021Q) where this assumption is not completely
true, since switch tagging piggybacks on the absence of a vlan_filtering
bridge. Moreover, management traffic (BPDU, PTP) for this switch doesn't
rely on switch tagging, but on a different mechanism. So it would make
sense to at least be able to terminate that.
Having DSA receive traffic it can't decode would put it in an impossible
situation: the eth_type_trans() function would invoke the DSA .rcv(),
which could not change skb->dev, then eth_type_trans() would be invoked
again, which again would call the DSA .rcv, and the packet would never
be able to exit the DSA filter and would spiral in a loop until the
whole system dies.
This happens because eth_type_trans() doesn't actually look at the skb
(so as to identify a potential tag) when it deems it as being
ETH_P_XDSA. It just checks whether skb->dev has a DSA private pointer
installed (therefore it's a DSA master) and that there exists a .rcv
callback (everybody except DSA_TAG_PROTO_NONE has that). This is
understandable as there are many switch tags out there, and exhaustively
checking for all of them is far from ideal.
The solution lies in introducing a filtering function for each tagging
protocol. In the absence of a filtering function, all traffic is passed
to the .rcv DSA callback. The tagging protocol should see the filtering
function as a pre-validation that it can decode the incoming skb. The
traffic that doesn't match the filter will bypass the DSA .rcv callback
and be left on the master netdevice, which wasn't previously possible.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides generic DSA code for using VLAN (802.1Q) tags for
the same purpose as a dedicated switch tag for injection/extraction.
It is based on the discussions and interest that has been so far
expressed in https://www.spinics.net/lists/netdev/msg556125.html.
Unlike all other DSA-supported tagging protocols, CONFIG_NET_DSA_TAG_8021Q
does not offer a complete solution for drivers (nor can it). Instead, it
provides generic code that driver can opt into calling:
- dsa_8021q_xmit: Inserts a VLAN header with the specified contents.
Can be called from another tagging protocol's xmit function.
Currently the LAN9303 driver is inserting headers that are simply
802.1Q with custom fields, so this is an opportunity for code reuse.
- dsa_8021q_rcv: Retrieves the TPID and TCI from a VLAN-tagged skb.
Removing the VLAN header is left as a decision for the caller to make.
- dsa_port_setup_8021q_tagging: For each user port, installs an Rx VID
and a Tx VID, for proper untagged traffic identification on ingress
and steering on egress. Also sets up the VLAN trunk on the upstream
(CPU or DSA) port. Drivers are intentionally left to call this
function explicitly, depending on the context and hardware support.
The expected switch behavior and VLAN semantics should not be violated
under any conditions. That is, after calling
dsa_port_setup_8021q_tagging, the hardware should still pass all
ingress traffic, be it tagged or untagged.
For uniformity with the other tagging protocols, a module for the
dsa_8021q_netdev_ops structure is registered, but the typical usage is
to set up another tagging protocol which selects CONFIG_NET_DSA_TAG_8021Q,
and calls the API from tag_8021q.h. Null function definitions are also
provided so that a "depends on" is not forced in the Kconfig.
This tagging protocol only works when switch ports are standalone, or
when they are added to a VLAN-unaware bridge. It will probably remain
this way for the reasons below.
When added to a bridge that has vlan_filtering 1, the bridge core will
install its own VLANs and reset the pvids through switchdev. For the
bridge core, switchdev is a write-only pipe. All VLAN-related state is
kept in the bridge core and nothing is read from DSA/switchdev or from
the driver. So the bridge core will break this port separation because
it will install the vlan_default_pvid into all switchdev ports.
Even if we could teach the bridge driver about switchdev preference of a
certain vlan_default_pvid (task difficult in itself since the current
setting is per-bridge but we would need it per-port), there would still
exist many other challenges.
Firstly, in the DSA rcv callback, a driver would have to perform an
iterative reverse lookup to find the correct switch port. That is
because the port is a bridge slave, so its Rx VID (port PVID) is subject
to user configuration. How would we ensure that the user doesn't reset
the pvid to a different value (which would make an O(1) translation
impossible), or to a non-unique value within this DSA switch tree (which
would make any translation impossible)?
Finally, not all switch ports are equal in DSA, and that makes it
difficult for the bridge to be completely aware of this anyway.
The CPU port needs to transmit tagged packets (VLAN trunk) in order for
the DSA rcv code to be able to decode source information.
But the bridge code has absolutely no idea which switch port is the CPU
port, if nothing else then just because there is no netdevice registered
by DSA for the CPU port.
Also DSA does not currently allow the user to specify that they want the
CPU port to do VLAN trunking anyway. VLANs are added to the CPU port
using the same flags as they were added on the user port.
So the VLANs installed by dsa_port_setup_8021q_tagging per driver
request should remain private from the bridge's and user's perspective,
and should not alter the VLAN semantics observed by the user.
In the current implementation a VLAN range ending at 4095 (VLAN_N_VID)
is reserved for this purpose. Each port receives a unique Rx VLAN and a
unique Tx VLAN. Separate VLANs are needed for Rx and Tx because they
serve different purposes: on Rx the switch must process traffic as
untagged and process it with a port-based VLAN, but with care not to
hinder bridging. On the other hand, the Tx VLAN is where the
reachability restrictions are imposed, since by tagging frames in the
xmit callback we are telling the switch onto which port to steer the
frame.
Some general guidance on how this support might be employed for
real-life hardware (some comments made by Florian Fainelli):
- If the hardware supports VLAN tag stacking, it should somehow back
up its private VLAN settings when the bridge tries to override them.
Then the driver could re-apply them as outer tags. Dedicating an outer
tag per bridge device would allow identical inner tag VID numbers to
co-exist, yet preserve broadcast domain isolation.
- If the switch cannot handle VLAN tag stacking, it should disable this
port separation when added as slave to a vlan_filtering bridge, in
that case having reduced functionality.
- Drivers for old switches that don't support the entire VLAN_N_VID
range will need to rework the current range selection mechanism.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed so that the newly introduced tag_8021q may access these
core DSA functions when built as a module.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows the driver to perform some manipulations of its own during
setup, using generic switchdev calls. Having the notifiers registered at
setup time is important because otherwise any switchdev transaction
emitted during this time would be ignored (dispatched to an empty call
chain).
One current usage scenario is for the driver to request DSA to set up
802.1Q based switch tagging for its ports.
There is no danger for the driver setup code to start racing now with
switchdev events emitted from the network stack (such as bridge core)
even if the notifier is registered earlier. This is because the network
stack needs a net_device as a vehicle to perform switchdev operations,
and the slave net_devices are registered later than the core driver
setup anyway (ds->ops->setup in dsa_switch_setup vs dsa_port_setup).
Luckily DSA doesn't need a net_device to carry out switchdev callbacks,
and therefore drivers shouldn't assume either that net_devices are
available at the time their switchdev callbacks get invoked.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>-
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates dsa hardware switch handling infrastructure to use the newer
intermediate representation for flow actions in matchall offloads.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all drivers can be probed using more traditional methods,
remove the legacy probe code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This hides the need to perform a two-phase transaction and construct a
switchdev_obj_port_vlan struct.
Call graph (including a function that will be introduced in a follow-up
patch) looks like this now (same for the *_vlan_del function):
dsa_slave_vlan_rx_add_vid dsa_port_setup_8021q_tagging
| |
| |
| +-------------+
| |
v v
dsa_port_vid_add dsa_slave_port_obj_add
| |
+-------+ +-------+
| |
v v
dsa_port_vlan_add
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if VLAN filtering is global, DSA will call this callback once per
each port. Drivers should not have to compare the global state with the
requested change. So let DSA do it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current behavior is not as obvious as one would assume (which is
that, if the driver set vlan_filtering_is_global = 1, then checking any
dp->vlan_filtering would yield the same result). Only the ports which
are actively enslaved into a bridge would have vlan_filtering set.
This makes it tricky for drivers to check what the global state is.
So fix this and make the struct dsa_switch hold this global setting.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ports are standalone (after they left the bridge), they should have
no VLAN filtering semantics (they should pass all traffic to the CPU).
Currently this is not true for switchdev drivers, because the bridge
"forgets" to unset that.
Normally one would think that doing this at the bridge layer would be a
better idea, i.e. call br_vlan_filter_toggle() from br_del_if(), similar
to how nbp_vlan_init() is called from br_add_if().
However what complicates that approach, and makes this one preferable,
is the fact that for the bridge core, vlan_filtering is a per-bridge
setting, whereas for switchdev/DSA it is per-port. Also there are
switches where the setting is per the entire device, and unsetting
vlan_filtering one by one, for each leaving port, would not be possible
from the bridge core without a certain level of awareness. So do this in
DSA and let drivers be unaware of it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some switches, the action of whether to parse VLAN frame headers and use
that information for ingress admission is configurable, but not per
port. Such is the case for the Broadcom BCM53xx and the NXP SJA1105
families, for example. In that case, DSA can prevent the bridge core
from trying to apply different VLAN filtering settings on net devices
that belong to the same switch.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows drivers to query the VLAN setting imposed by the bridge
driver directly from DSA, instead of keeping their own state based on
the .port_vlan_filtering callback.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the CONFIG symbols tristate and add help text.
The broadcom and Microchip KSZ tag drivers support two different
tagging protocols in one driver. Add a configuration option for the
drivers, and then options to select the protocol.
Create a submenu for the tagging drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
tab/space cleanup
Help text wording
NET_DSA_TAG_BRCM_COMMON and NET_DSA_TAG_KZS_COMMON hidden
v3:
More tabification
Punctuation
v4:
trailler->trailer
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that the driver is compiled with both
CONFIG_NET_DSA_TAG_BRCM and CONFIG_NET_DSA_TAG_BRCM_PREPEND disabled.
This results in warnings about unused symbols. Add some conditional
compilation to avoid this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2
Reorder patch to before tag drivers can be modules
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that tag drivers dynamically register, we don't need the static
table. Remove it. This also means the tag driver structures can be
made static.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the _get and _put functions to make use of the list of tag
drivers. Also, trigger the loading of the module, based on the alias
information. The _get function takes a reference on the tag driver, so
it cannot be unloaded, and the _put function releases the reference.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2:
Make tag_driver_register void
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DSA switch driver is unloaded, the lock on the tag driver
should be released so the module can be unloaded. Add the needed calls,
but leave the actual release code as a stub.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_resolve_tag_protocol() is used to find the tagging driver needed
by a switch driver. When the tagging drivers become modules, it will
be necassary to take a reference on the module to prevent it being
unloaded. So rename this function to _get() to indicate it has some
locking properties.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The none tagger is special in that it does not live in a tag_*.c file,
but is within the core. Register/unregister when DSA is
loaded/unloaded.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let the tag drivers register themselves with the DSA core, keeping
them in a linked list.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2
Signed-off-by: David S. Miller <davem@davemloft.net>
A DSA tag driver module will need to register the tag protocols it
implements with the DSA core. Add macros containing this boiler plate.
The registration/unregistration code is currently just a stub. A Later
patch will add the real implementation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2
Fix indent of #endif
Rewrite to move list pointer into a new structure
v3
Move kdoc next to macro
Fix THIS_MODULE indentation
Signed-off-by: David S. Miller <davem@davemloft.net>
In order that we can match the tagging protocol a switch driver
request to the tagger, we need to know what protocol the tagger
supports. Add this information to the ops structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2
More tag protocol to end of structure to keep hot members at the beginning.
Signed-off-by: David S. Miller <davem@davemloft.net>
All the tag drivers are some variant of GPL. Add a MODULE_LICENSE()
indicating this, so the drivers can later be compiled as modules.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the tag drivers become modules, we will need to dynamically load
them based on what the switch drivers need. Add aliases to map between
the TAG protocol and the driver.
In order to do this, we need the tag protocol number as something
which the C pre-processor can stringinfy. Only the compiler knows the
value of an enum, CPP cannot use them. So add #defines.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than keep a list to map a tagger ops to a name, place the name
into the ops structure. This removes the hard coded list, a step
towards making the taggers more dynamic.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2:
Move name to end of structure, keeping the hot entries at the beginning.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an SPDX header, and remove the license boilerplate text.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor comment merge conflict in mlx5.
Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the switch ID down the to devlink through devlink_port_attrs_set()
so it can be used by devlink_compat_switch_id_get(). Leave
ndo_get_port_parent_id implementation only for legacy.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend devlink_port_attrs_set() to pass switch ID for ports which are
part of switch and store it in port attrs. For other ports, this is
NULL.
Note that this allows the driver to group devlink ports into one or more
switches according to the actual topology.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before creating a slave netdevice, get the mac address from DTS and
apply in case it is valid.
Signed-off-by: Xiaofei Shen <xiaofeis@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flow_dissect for qca tagged packet to get the right hash.
Signed-off-by: Xiaofei Shen <xiaofeis@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since each non-legacy slave has its own devlink port instance
correctly set, rely on devlink core to generate correct phys port name.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for devlink compat functions to work, implement
ndo_get_devlink_port. Legacy slaves does not have devlink port instances
created for themselves.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When phylink_of_phy_connect fails, dsa_slave_phy_setup tries to save the
day by connecting to an alternative PHY, none other than a PHY on the
switch's internal MDIO bus, at an address equal to the port's index.
However this does not take into consideration the scenario when the
switch that failed to probe an external PHY does not have an internal
MDIO bus at all.
Fixes: aab9c4067d ("net: dsa: Plug in PHYLINK support")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers are becoming more dependent on NET_DEVLINK being selected
in configuration. With upcoming compat functions, the behavior would be
wrong in case devlink was not compiled in. So make the drivers select
NET_DEVLINK and rely on the functions being there, not just stubs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since attrs are static during the existence of devlink port, set the
before registration of the port.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
devlink functions are in use, so include the related header file.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were skipping the prepare phase which causes some problems with at
least a couple of drivers:
- mv88e6xxx chooses to skip programming VID = 0 with -EOPNOTSUPP in
the prepare phase, but we would still try to force this VID since we
would only call the commit phase and so we would get the driver to
return -EINVAL instead
- qca8k does not currently have a port_vlan_add() callback implemented,
yet we would try to call that unconditionally leading to a NPD
Fix both issues by conforming to the current model doing a
prepare/commit phase, this makes us consistent throughout the code and
assumptions.
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: Michal Vokáč <michal.vokac@ysoft.com>
Fixes: 061f6a505a ("net: dsa: Add ndo_vlan_rx_{add, kill}_vid implementation")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ9893 switch is similar to KSZ9477 switch except the ingress tail tag
has 1 byte instead of 2 bytes. The size of the portmap is smaller and
so the override and lookup bits are also moved.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have converted all possible callers to using a switchdev
notifier for attributes we do not have a need for implementing
switchdev_ops anymore, and this can be removed from all drivers the
net_device structure.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patches will change the way we communicate setting a port's
attribute and use notifiers towards that goal.
Prepare DSA to support receiving notifier events targeting
SWITCHDEV_PORT_ATTR_SET from both atomic and process context and use a
small helper to translate the event notifier into something that
dsa_slave_port_attr_set() can process.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Being able to build devlink as a module causes growing pains.
First all drivers had to add a meta dependency to make sure
they are not built in when devlink is built as a module. Now
we are struggling to invoke ethtool compat code reliably.
Make devlink code built-in, users can still not build it at
all but the dynamically loadable module option is removed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./net/dsa/port.c:294:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 284, but without a corresponding object release within this function.
./net/dsa/dsa2.c:627:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:630:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:636:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:639:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
No current DSA driver makes use of the phydev parameter passed to the
disable_port call. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to properly support VLAN filtering being enabled/disabled on a
bridge, while having other ports being non bridge port members, we need
to support the ndo_vlan_rx_{add,kill}_vid callbacks in order to make
sure the non-bridge ports can continue receiving VLAN tags, even when
the switch is globally configured to do ingress/egress VID checking.
Since we can call dsa_port_vlan_{add,del} with a bridge_dev pointer
NULL, we now need to check that in these two functions.
We specifically deal with two possibly problematic cases:
- creating a bridge VLAN entry while there is an existing VLAN device
claiming that same VID
- creating a VLAN device while there is an existing bridge VLAN entry
with that VID
Those are both resolved with returning -EBUSY back to user-space.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN devices on top of a DSA network device which is already part of a
bridge and with said bridge being VLAN aware should not be allowed to be
enslaved into that bridge. For one, this duplicates functionality
offered by the VLAN aware bridge which supports tagged and untagged VLAN
frames processing and it would make things needlessly complex to e.g.:
propagate FDB/MDB accordingly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the bridge no longer calling switchdev_port_attr_get() to obtain
the supported bridge port flags from a driver but instead trying to set
the bridge port flags directly and relying on driver to reject
unsupported configurations, we can effectively get rid of
switchdev_port_attr_get() entirely since this was the only place where
it was called.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have converted the bridge code and the drivers to check for
bridge port(s) flags at the time we try to set them, there is no need
for a get() -> set() sequence anymore and
SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS_SUPPORT therefore becomes unused.
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for removing SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS_SUPPORT,
add support for a function that processes the
SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS and
SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS attributes and returns not
supported for any flag set, since DSA does not currently support
toggling those bridge port attributes (yet).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switches work by learning the MAC address for each attached station by
monitoring traffic from each station. When a station sends a packet,
the switch records which port the MAC address is connected to.
With IPv4 networking, before communication commences with a neighbour,
an ARP packet is broadcasted to all stations asking for the MAC address
corresponding with the IPv4. The desired station responds with an ARP
reply, and the ARP reply causes the switch to learn which port the
station is connected to.
With IPv6 networking, the situation is rather different. Rather than
broadcasting ARP packets, a "neighbour solicitation" is multicasted
rather than broadcasted. This multicast needs to reach the intended
station in order for the neighbour to be discovered.
Once a neighbour has been discovered, and entered into the sending
stations neighbour cache, communication can restart at a point later
without sending a new neighbour solicitation, even if the entry in
the neighbour cache is marked as stale. This can be after the MAC
address has expired from the forwarding cache of the DSA switch -
when that occurs, there is a long pause in communication.
Our DSA implementation for mv88e6xxx switches disables flooding of
multicast and unicast frames for bridged ports. As per the above
description, this is fine for IPv4 networking, since the broadcasted
ARP queries will be sent to and received by all stations on the same
network. However, this breaks IPv6 very badly - blocking neighbour
solicitations and later causing connections to stall.
The defaults that the Linux bridge code expect from bridges are for
unknown unicast and unknown multicast frames to be flooded to all ports
on the bridge, which is at odds to the defaults adopted by our DSA
implementation for mv88e6xxx switches.
This commit enables by default flooding of both unknown unicast and
unknown multicast frames whenever a port is added to a bridge, and
disables the flooding when a port leaves the bridge. This means that
mv88e6xxx DSA switches now behave as per the bridge(8) man page, and
IPv6 works flawlessly through such a switch.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux bridge implementation allows various properties of the bridge
to be controlled, such as flooding unknown unicast and multicast frames.
This patch adds the necessary DSA infrastructure to allow the Linux
bridge support to control these properties for DSA switches.
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[florian: Add missing dp and ds variables declaration to fix build]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DSA port is added to a bridge and brought up, the resulting STP
state programmed into the hardware depends on the order that these
operations are performed. However, the Linux bridge code believes that
the port is in disabled mode.
If the DSA port is first added to a bridge and then brought up, it will
be in blocking mode. If it is brought up and then added to the bridge,
it will be in disabled mode.
This difference is caused by DSA always setting the STP mode in
dsa_port_enable() whether or not this port is part of a bridge. Since
bridge always sets the STP state when the port is added, brought up or
taken down, it is unnecessary for us to manipulate the STP state.
Apparently, this code was copied from Rocker, and the very next day a
similar fix for Rocker was merged but was not propagated to DSA. See
e47172ab7e ("rocker: put port in FORWADING state after leaving bridge")
Fixes: b73adef677 ("net: dsa: integrate with SWITCHDEV for HW bridging")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RPS not work for DSA devices since the 'skb_get_hash'
will always get the invalid hash for dsa tagged packets.
"[PATCH] tag_mtk: add flow_dissect callback to the ops struct"
introduced the flow_dissect callback to get the right hash for
MTK tagged packet. Tag_dsa and tag_edsa also need to implement
the callback.
Signed-off-by: Rundong Ge <rdong.ge@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag offload_fwd_mark is set as the switch can forward frames by
itself.
This can be considered a fix to a problem introduced in commit
c2e866911e where the port membership are not set in sync. The flag
offload_fwd_mark just needs to be set in tag_ksz.c to prevent the software
bridge from forwarding duplicate multicast frames.
Fixes: c2e866911e ("microchip: break KSZ9477 DSA driver into two files")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = alloc(struct_size(instance, entry, count), GFP_KERNEL)
Notice that, in this case, variable size is not necessary, hence it is
removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA implements SWITCHDEV_ATTR_ID_PORT_PARENT_ID and we want to get rid
of switchdev_ops eventually, ease that migration by implementing a
ndo_get_port_parent_id() function which returns what
switchdev_port_attr_get() would do.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function can't succeed if dp->pl is NULL. It will Oops inside the
call to return phylink_ethtool_get_eee(dp->pl, e);
Fixes: 1be52e97ed ("dsa: slave: eee: Allow ports to use phylink")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The unbalance of master's promiscuity or allmulti will happen after ifdown
and ifup a slave interface which is in a bridge.
When we ifdown a slave interface , both the 'dsa_slave_close' and
'dsa_slave_change_rx_flags' will clear the master's flags. The flags
of master will be decrease twice.
In the other hand, if we ifup the slave interface again, since the
slave's flags were cleared the 'dsa_slave_open' won't set the master's
flag, only 'dsa_slave_change_rx_flags' that triggered by 'br_add_if'
will set the master's flags. The flags of master is increase once.
Only propagating flag changes when a slave interface is up makes
sure this does not happen. The 'vlan_dev_change_rx_flags' had the
same problem and was fixed, and changes here follows that fix.
Fixes: 91da11f870 ("net: Distributed Switch Architecture protocol support")
Signed-off-by: Rundong Ge <rdong.ge@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-up patch will enable vetoing of FDB entries. Make it possible
to communicate details of why an FDB entry is not acceptable back to the
user.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers may not be able to support certain FDB entries, and an error
code is insufficient to give clear hints as to the reasons of rejection.
In order to make it possible to communicate the rejection reason, extend
ndo_fdb_add() with an extack argument. Adapt the existing
implementations of ndo_fdb_add() to take the parameter (and ignore it).
Pass the extack parameter when invoking ndo_fdb_add() from rtnl_fdb_add().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is not currently way to infer the port number through sysfs that
is being used as the CPU port number. Overlay a ndo_get_phys_port_name()
operation onto the DSA master network device in order to retrieve that
information.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the destination address is link local, add override bit into the
switch tag to let such a packet through the switch even if the port is
blocked.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out common code from the tag_ksz , so that the code can be used
with other KSZ family switches which use differenly sized tags.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the tag Kconfig option and related macros in preparation for
addition of new KSZ family switches with different tag formats.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts, seemingly all over the place.
I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.
The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.
The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.
cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.
__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy. Or at least I think it was :-)
Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.
The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous change tries to set the MTU on the master device to take
into account the DSA overheads. This patch tries to reset the master
device back to the default MTU.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA tagging of frames sent over the master interface to the switch
increases the size of the frame. Such frames can then be bigger than
the normal MTU of the master interface, and it may drop them. Use the
overhead information from the tagger to set the MTU of the master
device to include this overhead.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each DSA tag protocol needs to add additional headers to the Ethernet
frame in order to direct it towards a specific switch egress port. It
must also remove the head from a frame received from a
switch. Indicate the maximum size of these headers in the tag protocol
ops structure, so the core can take these overheads into account.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
While introducing the DSA tagging protocol attribute, it was added to the DSA
slave network devices, but those actually see untagged traffic (that is their
whole purpose). Correct this mistake by putting the tagging sysfs attribute
under the DSA master network device where this is the information that we need.
While at it, also correct the sysfs documentation mistake that missed the
"dsa/" directory component of the attribute.
Fixes: 98cdb48071 ("net: dsa: Expose tagging protocol to user-space")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to an explicit check in rocker_world_port_obj_vlan_add(),
dsa_slave_switchdev_event() resp. port_switchdev_event(), VLAN objects
that are added to a device that is not a front-panel port device are
ignored. Therefore this check is immaterial.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop switchdev_ops.switchdev_port_obj_add and _del. Drop the uses of
this field from all clients, which were migrated to use switchdev
notification in the previous patches.
Add a new function switchdev_port_obj_notify() that sends the switchdev
notifications SWITCHDEV_PORT_OBJ_ADD and _DEL.
Update switchdev_port_obj_del_now() to dispatch to this new function.
Drop __switchdev_port_obj_add() and update switchdev_port_obj_add()
likewise.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patches will change the way of distributing port object
changes from a switchdev operation to a switchdev notifier. The
switchdev code currently recursively descends through layers of lower
devices, eventually calling the op on a front-panel port device. The
notifier will instead be sent referencing the bridge port device, which
may be a stacking device that's one of front-panel ports uppers, or a
completely unrelated device.
DSA currently doesn't support any other uppers than bridge.
SWITCHDEV_OBJ_ID_HOST_MDB and _PORT_MDB objects are always notified on
the bridge port device. Thus the only case that a stacked device could
be validly referenced by port object notifications are bridge
notifications for VLAN objects added to the bridge itself. But the
driver explicitly rejects such notifications in dsa_port_vlan_add(). It
is therefore safe to assume that the only interesting case is that the
notification is on a front-panel port netdevice. Therefore keep the
filtering by dsa_slave_dev_check() in place.
To handle SWITCHDEV_PORT_OBJ_ADD and _DEL, subscribe to the blocking
notifier chain. Dispatch to rocker_port_obj_add() resp. _del() to
maintain the behavior that the switchdev operation based code currently
has.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a problem introduced by:
commit 2cde6acd49 ("netpoll: Fix __netpoll_rcu_free so that it can hold the rtnl lock")
When using netconsole on a bond, __netpoll_cleanup can asynchronously
recurse multiple times, each __netpoll_free_async call can result in
more __netpoll_free_async's. This means there is now a race between
cleanup_work queues on multiple netpoll_info's on multiple devices and
the configuration of a new netpoll. For example if a netconsole is set
to enable 0, reconfigured, and enable 1 immediately, this netconsole
will likely not work.
Given the reason for __netpoll_free_async is it can be called when rtnl
is not locked, if it is locked, we should be able to execute
synchronously. It appears to be locked everywhere it's called from.
Generalize the design pattern from the teaming driver for current
callers of __netpoll_free_async.
CC: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, an FDB entry only ceases being offloaded when it is deleted.
This changes with VxLAN encapsulation.
Devices capable of performing VxLAN encapsulation usually have only one
FDB table, unlike the software data path which has two - one in the
bridge driver and another in the VxLAN driver.
Therefore, bridge FDB entries pointing to a VxLAN device are only
offloaded if there is a corresponding entry in the VxLAN FDB.
Allow clearing the offload indication in case the corresponding entry
was deleted from the VxLAN FDB.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
put_device has taken the null pinter check into account. So it is
safe to remove the duplicated check before put_device.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gswip tag was missing in the dsa_tag_protocol_to_str() function, add it.
Fixes: 7969119293 ("net: dsa: Add Lantiq / Intel GSWIP tag support")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This handles the tag added by the PMAC on the VRX200 SoC line.
The GSWIP uses internally a GSWIP special tag which is located after the
Ethernet header. The PMAC which connects the GSWIP to the CPU converts
this special tag used by the GSWIP into the PMAC special tag which is
added in front of the Ethernet header.
This was tested with GSWIP 2.1 found in the VRX200 SoCs, other GSWIP
versions use slightly different PMAC special tags.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no way for user-space to know what a given DSA network device's
tagging protocol is. Expose this information through a dsa/tagging
attribute which reflects the tagging protocol currently in use.
This is helpful for configuration (e.g: none behaves dramatically
different wrt. bridges) as well as for packet capture tools when there
is not a proper Ethernet type available.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 52638f71fc ("dsa: Move gpio reset into switch driver")
moved the GPIO handling into the switch drivers but forgot
to remove the GPIO header includes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 90b73b77d0, list_head is no longer needed.
Now we just need to convert the list iteration to array
iteration for drivers.
Fixes: 90b73b77d0 ("net: sched: change action API to use array of pointers to actions")
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For a port to be able to use EEE, both the MAC and the PHY must
support EEE. A phy can be provided by both a phydev or phylink. Verify
at least one of these exist, not just phydev.
Fixes: aab9c4067d ("net: dsa: Plug in PHYLINK support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
If a DSA slave network device was previously disabled, there is no need
to suspend or resume it.
Fixes: 2446254915 ("net: dsa: allow switch drivers to implement suspend/resume hooks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We avoid 2 VLAs by using a pre-allocated field in dsa_switch. We also
try to avoid dynamic allocation whenever possible (when using fewer than
bits-per-long ports, which is the common case).
Link: http://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Link: http://lkml.kernel.org/r/20180505185145.GB32630@lunn.ch
Signed-off-by: Salvatore Mesoraca <s.mesoraca16@gmail.com>
[kees: tweak commit subject and message slightly]
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the extact struct from a tc qdisc add to the block bind function and,
in turn, to the setup_tc ndo of binding device via the tc_block_offload
struct. Pass this back to any block callback registrations to allow
netlink logging of fails in the bind process.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When pskb_trim_rcsum fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling pskb_trim_rcsum.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-up patch enables emitting VLAN notifications for the bridge CPU
port in addition to the existing slave port notifications. These
notifications have orig_dev set to the bridge in question.
Because there's no specific support for these VLANs, just ignore the
notifications to maintain the current behavior.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.
TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.
The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.
Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the attrs and allow to expose port flavour to user via devlink.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if commit 1d27732f41 ("net: dsa: setup and teardown ports") indicated
that registering a devlink instance for unused ports is not a problem, and this
is true, this can be confusing nonetheless, so let's not do it.
Fixes: 1d27732f41 ("net: dsa: setup and teardown ports")
Reported-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for PHYLINK within the DSA subsystem in order to support more
complex devices such as pluggable (SFP) and non-pluggable (SFF) modules, 10G
PHYs, and traditional PHYs. Using PHYLINK allows us to drop some amount of
complexity we had while probing fixed and non-fixed PHYs using Device Tree.
Because PHYLINK separates the Ethernet MAC/port configuration into different
stages, we let switch drivers implement those, and for now, we maintain
functionality by calling dsa_slave_adjust_link() during
phylink_mac_link_{up,down} which provides semantically equivalent steps.
Drivers willing to take advantage of PHYLINK should implement the phylink_mac_*
operations that DSA wraps.
We cannot quite remove the adjust_link() callback just yet, because a number of
drivers rely on that for configuring their "CPU" and "DSA" ports, this is done
dsa_port_setup_phy_of() and dsa_port_fixed_link_register_of() still.
Drivers that utilize fixed links for user-facing ports (e.g: bcm_sf2) will need
to implement phylink_mac_ops from now on to preserve functionality, since PHYLINK
*does not* create a phy_device instance for fixed links.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we use PHYLIB to manage the per-port link indication, this will
also be reflected correctly in the network device's carrier state, so we
can use ethtool_op_get_link() instead.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding support for PHYLINK within DSA, define a number of
operations that we will need and that switch drivers can start implementing.
Proper integration with PHYLINK will follow in subsequent patches.
We start selecting PHYLINK (which implies PHYLIB) in net/dsa/Kconfig
such that drivers can be guaranteed that this dependency is properly
taken care of and can start referencing PHYLINK helper functions without
requiring stubs or anything.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch enables sending notifications also for events on FDB
entries that weren't added by the user. Give the drivers the information
necessary to distinguish between the two origins of FDB entries.
To maintain the current behavior, have switchdev-implementing drivers
bail out on notifications about non-user-added FDB entries. In case of
mlxsw driver, allow a call to mlxsw_sp_span_respin() so that SPAN over
bridge catches up with the changed FDB.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the same type of ethtool diversion that we have for
ETH_SS_STATS and make it work with ETH_SS_PHY_STATS. This allows
providing PHY level statistics for CPU ports that are directly
connecting to a PHY device.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for having more call sites attempting to obtain a
reference against a PHY device corresponding to a particular port,
introduce a helper function for that purpose.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we largely assumed that we were interested in ETH_SS_STATS
type of strings for all ethtool operations, this is about to change with
the introduction of additional string sets, e.g: ETH_SS_PHY_STATS.
Update all functions to take an appropriate stringset argument and act
on it when it is different than ETH_SS_STATS for now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is completely redundant with what netdev_set_default_ethtool_ops()
does, we are always guaranteed to have a valid dev->ethtool_ops pointer,
however, within that structure, not all function calls may be populated,
so we still have to check them individually.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell switches under some conditions will pass a frame to the
host with the port being the CPU port. Such frames are invalid, and
should be dropped. Not dropping them can result in a crash when
incrementing the receive statistics for an invalid port.
Reported-by: Chris Healy <cphealy@gmail.com>
Fixes: 91da11f870 ("net: Distributed Switch Architecture protocol support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
During the conversion to dsa_is_user_port(), a condition ended up being
reversed, which would prevent the creation of any user port when using
the legacy binding and/or platform data, fix that.
Fixes: 4a5b85ffe2 ("net: dsa: use dsa_is_user_port everywhere")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By passing the port, we allow different ports to have different
statistics. This is useful since some ports have SERDES interfaces
with their own statistic counters.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forward the rx/tx timestamp machinery from the dsa infrastructure to the
switch driver.
On the rx side, defer delivery of skbs until we have an rx timestamp.
This mimicks the behavior of skb_defer_rx_timestamp.
On the tx side, identify PTP packets, clone them, and pass them to the
underlying switch driver before we transmit. This mimicks the behavior
of skb_tx_timestamp.
Adjusted txstamp API to keep the allocation and freeing of the clone
in the same central function by Richard Cochran
Signed-off-by: Brandon Streiff <brandon.streiff@ni.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to the dsa slave network device so that
switch drivers can implement the SIOC[GS]HWTSTAMP ioctls and the
ethtool timestamp-info interface.
Signed-off-by: Brandon Streiff <brandon.streiff@ni.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for enabling the internal PHY for a 'cpu' port.
It has been tested on GE B850v3, B650v3 and B450v3, which have a
built-in MV88E6240 switch hardwired to a PCIe based network card.
On these machines the internal PHY of the i210 network card and
the Marvell switch are connected to each other and must be enabled
for properly using the switch. While the i210 PHY will be enabled
when the network interface is enabled, the switch's port is not
exposed as network interface. Additionally the mv88e6xxx driver
resets the chip during probe, so the PHY is disabled without this
patch.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having the different master network device drivers
potentially used by DSA/Broadcom tags, move the padding necessary for
the switches to accept short packets where it makes most sense: within
tag_brcm.c. This avoids multiplying the number of similar commits to
e.g: bgmac, bcmsysport, etc.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to make the dsa_legacy_register() stub return 0 in order for
dsa_init_module() to successfully register and continue registering the
ETH_P_XDSA packet handler.
Fixes: 2a93c1a365 ("net: dsa: Allow compiling out legacy support")
Reported-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three sets of overlapping changes, two in the packet scheduler
and one in the meson-gxl PHY driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to let MT7530 switch can recognize well those egress packets
having both special tag and VLAN tag, the information about the special
tag should be carried on the existing VLAN tag. On the other hand, it's
unnecessary for extra handling for ingress packets when VLAN tag is
present since it is able to put the VLAN tag after the special tag and
then follow the existing way to parse.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a configuration option: CONFIG_NET_DSA_LEGACY allowing to compile out
support for the old platform device and Device Tree binding registration.
Support for these configurations is scheduled to be removed in 4.17.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcfm_dev always points to the correct netdev and we already
hold a refcnt, so no need to use tcfm_ifindex to lookup again.
If we would support moving target netdev across netns, using
pointer would be better than ifindex.
This also fixes dumping obsolete ifindex, now after the
target device is gone we just dump 0 as ifindex.
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA ports also need to have a dedicated CPU port assigned to them,
because they need to know where to egress frames targeting the CPU,
e.g. To_Cpu frames received on a Marvell Tag port.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a MAC address is added to or removed from a switch port in the
fabric, the target switch must program its port and adjacent switches
must program their local DSA port used to reach the target switch.
For this purpose, use the dsa_towards_port() helper to identify the
local switch port which must be programmed.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch brings no functional changes.
It moves out the MDB code iterating on a multicast group into new
dsa_switch_mdb_{prepare,add}_bitmap() functions.
This gives us a better isolation of the two switchdev phases.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch brings no functional changes.
It moves out the VLAN code iterating on a list of VLAN members into new
dsa_switch_vlan_{prepare,add}_bitmap() functions.
This gives us a better isolation of the two switchdev phases.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA switch MDB ops pass the switchdev_trans structure down to the
drivers, but no one is using them and they aren't supposed to anyway.
Remove the trans argument from MDB prepare and add operations.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA switch VLAN ops pass the switchdev_trans structure down to the
drivers, but no one is using them and they aren't supposed to anyway.
Remove the trans argument from VLAN prepare and add operations.
At the same time, fix the following checkpatch warning:
WARNING: line over 80 characters
#74: FILE: drivers/net/dsa/dsa_loop.c:177:
+ const struct switchdev_obj_port_vlan *vlan)
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting the refcount to 0 when allocating a tree to match the number of
switch devices it holds may cause an 'increment on 0; use-after-free',
if CONFIG_REFCOUNT_FULL is enabled.
To fix this, do not decrement the refcount of a newly allocated tree,
increment it when an already allocated tree is found, and decrement it
after the probing of a switch, as done with the previous behavior.
At the same time, make dsa_tree_get and dsa_tree_put accept a NULL
argument to simplify callers, and return the tree after incrementation,
as most kref users like of_node_get and of_node_put do.
Fixes: 8e5bf9759a ("net: dsa: simplify tree reference counting")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lan9303 set bits in the host CPU tag indicating if a ingress frame
is a trapped IGMP or STP frame. Use these bits to calculate
skb->offload_fwd_mark more efficiently.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA now uses one of the symbols exported by the bridge,
br_vlan_enabled(). This has a stub, if the bridge is not
enabled. However, if the bridge is enabled, we cannot have DSA built
in and the bridge as a module, otherwise we get undefined symbols at
link time:
net/dsa/port.o: In function `dsa_port_vlan_add':
net/dsa/port.c:255: undefined reference to `br_vlan_enabled'
net/dsa/port.o: In function `dsa_port_vlan_del':
net/dsa/port.c:270: undefined reference to `br_vlan_enabled'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new type: DSA_TAG_PROTO_PREPEND which allows us to support for the
4-bytes Broadcom tag that we already support, but in a format where it
is pre-pended to the packet instead of located between the MAC SA and
the Ethertyper (DSA_TAG_PROTO_BRCM).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting the same Broadcom tag format, but instead
of inserted between the MAC SA and EtherType, prepended to the Ethernet
frame, restructure the code a little bit to make that possible and take
an offset parameter.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of drivers want to check whether the configured CPU port is a
possible configuration for enabling tagging, pass down the CPU port
number so they verify that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that IGMP packets no longer is flooded in HW, we want the SW bridge to
forward packets based on bridge configuration. To make that happen,
IGMP packets must have skb->offload_fwd_mark = 0.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The software bridge needs to know if a packet has already been bridged
by hardware offload to ports in the same hardware offload, in order
that it does not re-flood them, causing duplicates. This is
particularly true for broadcast and multicast traffic which the host
has requested.
By setting offload_fwd_mark in the skb the bridge will only flood to
ports in other offloads and other netifs. Set this flag in the DSA and
EDSA tag driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
SWITCHDEV_ATTR_ID_PORT_PARENT_ID is used by the software bridge when
determining which ports to flood a packet out. If the packet
originated from a switch, it assumes the switch has already flooded
the packet out the switches ports, so the bridge should not flood the
packet itself out switch ports. Ports on the same switch are expected
to return the same parent ID when SWITCHDEV_ATTR_ID_PORT_PARENT_ID is
called.
DSA gets this wrong with clusters of switches. As far as the software
bridge is concerned, the cluster is all one switch. A packet from any
switch in the cluster can be assumed to have been flooded as needed
out of all ports of the cluster, not just the switch it originated
from. Hence all ports of a cluster should return the same parent. The
old implementation did not, each switch in the cluster had its own ID.
Also wrong was that the ID was not unique if multiple DSA instances
are in operation.
Use the tree ID as the parent ID, which is the same for all switches
in a cluster and unique across switch clusters.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code does not return after successfully preparing the VLAN
addition on every ports member of a it. Fix this.
Fixes: 1ca4aa9cd4 ("net: dsa: check VLAN capability of every switch")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code does not return after successfully preparing the MDB
addition on every ports member of a multicast group. Fix this.
Fixes: a1a6b7ea7f ("net: dsa: add cross-chip multicast support")
Reported-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The software bridge can be build with vlan filtering support
included. However, by default it is turned off. In its turned off
state, it still passes VLANs via switchev, even though they are not to
be used. Don't pass these VLANs to the hardware. Only do so when vlan
filtering is enabled.
This fixes at least one corner case. There are still issues in other
corners, such as when vlan_filtering is later enabled.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the host indicates when a multicast group should be forwarded
from the switch to the host, don't do it by default.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The notify mechanism does not need to modify the port it is notifying.
So make the parameter const.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to handle switchdev host mdb add/del. Since DSA uses one of
the switch ports as a transport to the host, we just need to add an
MDB on this port.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit brings no functional changes. It gets rid of the underscore
prefixed _dsa_register_switch and _dsa_unregister_switch functions in
favor of dsa_switch_probe() which parses and adds a switch to a tree and
dsa_switch_remove() which removes a switch from a tree.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the tree setup is centralized, we can simplify the code a bit
more by setting up or tearing down the tree directly when adding or
removing a switch to/from it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The *_complete() functions take too much arguments to do only one thing:
they try to fetch the dsa_port structures corresponding to device nodes
under the "link" list property of DSA ports, and use them to setup the
routing table of switches.
This patch simplifies them by providing instead simpler
dsa_{port,switch,tree}_setup_routing_table functions which return a
boolean value, true if the tree is complete.
dsa_tree_setup_routing_table is called inside dsa_tree_setup which
simplifies the switch registering function as well.
A switch's routing table is now initialized before its setup.
This also makes dsa_port_is_valid obsolete, remove it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The OF code provides a of_for_each_phandle() helper to iterate over
phandles. Use it instead of arbitrary iterating ourselves over the list
of phandles hanging to the "link" property of the port's device node.
The of_phandle_iterator_next() helper calls of_node_put() itself on
it.node. Thus We must only do it ourselves if we break the loop.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having two dsa_ds_find_port_dn (which returns a bool) and
dsa_dst_find_port_dn (which returns a switch) functions, provide a more
explicit dsa_tree_find_port_by_node function which returns a matching
port.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_dsa_port_apply and dsa_cpu_port_apply functions do exactly the
same. The dsa_user_port_apply function does not try to register a fixed
link but try to create a slave.
This commit factorizes and scopes all that in two convenient
dsa_port_setup and dsa_port_teardown functions.
It won't hurt to register a devlink_port for unused port as well.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patches brings no functional changes. It removes the unused dst
argument from the dsa_ds_apply and dsa_ds_unapply functions, rename them
to dsa_switch_setup and dsa_switch_teardown for a more explicit scope.
This clarifies the steps of the setup or teardown of a switch fabric.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit provides better scope for the DSA tree setup and teardown
functions. It renames the "applied" bool to "setup" and print a message
when the tree is setup, as it is done during teardown.
At the same time, check dst->setup in dsa_tree_setup, where it is set to
true.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DSA helpers to setup and teardown a master net device wired to its
CPU port. This centralizes the dsa_ptr assignment.
This also makes the master ethtool helpers static at the same time.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_dst_parse function called just before dsa_dst_apply does not
parse the tree but does only one thing: it assigns the default CPU port
to dst->cpu_dp and to each user ports.
This patch simplifies this by calling a dsa_tree_setup_default_cpu
function at the beginning of dsa_dst_apply directly.
A dsa_port_is_user helper is added for convenience.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A DSA port has a dedicated CPU port assigned to it, stored in the cpu_dp
member. It is not meant to be modified by a port, thus make it const.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove scripts/checkpatch.pl CHECKs by adjusting indenting.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the dsa_port_parse_cpu() function to resolve the tagging protocol
at port parsing time, instead of waiting for the whole tree to be
complete.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dsa_port_parse_user, dsa_port_parse_dsa and dsa_port_parse_cpu
functions to factorize the code shared by both OF and pdata parsing.
They don't do much for the moment but will be extended later to support
tagging protocol resolution for example.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When parsing a port, simply use of_property_read_bool which checks the
presence of a given property, instead of parsing the link phandle.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When parsing a switch, we have to identify to which tree it belongs and
parse its ports. Provide two functions to separate the OF and platform
data specific paths.
Also use the of_property_read_variable_u32_array function to parse the
OF member array instead of calling of_property_read_u32_index twice.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will need a reference to the dsa_switch_tree when parsing a CPU port,
so fetch it right after parsing the member and before parsing ports.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the unnecessary index argument from the
dsa_dst_add_ds and dsa_dst_del_ds functions and renames them to
dsa_tree_add_switch and dsa_tree_remove_switch respectively.
In addition to a more explicit scope, we now check the presence of an
existing switch with the same index directly within dsa_tree_add_switch.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename dsa_get_dst to dsa_tree_find since it doesn't increment the
reference counter, rename dsa_add_dst to dsa_tree_alloc for symmetry
with dsa_tree_free, and provide a convenient dsa_tree_touch function to
find or allocate a new tree.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide convenient dsa_tree_get and dsa_tree_put functions scoping a DSA
tree used to increment and decrement its reference counter, instead of
poking directly its kref structure.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA trees have a refcount used to automatically free the dsa_switch_tree
structure once there is no switch devices inside of it.
The refcount is incremented when a switch is added to the tree, and
decremented when it is removed from it.
But because of kref_init, the refcount is also incremented at
initialization, and when looking up the tree from the list for symmetry.
Thus the current code stores the number of switches plus one, and makes
the switch registration more complex.
To simplify the switch registration function, we reset the refcount to
zero after initialization and don't increment it when looking up a tree.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to a DSA switch and port, rename the tree index from "tree" to
"index" and make it an unsigned int because it isn't supposed to be less
than 0.
u32 is an OF specific data used to retrieve the value and has no need to
be propagated up to the tree index.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This restores the original behaviour before the block callbacks were
introduced. Allow the drivers to do binding of block always, no matter
if the NETIF_F_HW_TC feature is on or off. Move the check to the block
callback which is called for rule insertion.
Reported-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip flood broadcast and unknown multicast frames.
On receive set skb->offload_fwd_mark to prevent the SW from flooding to the
same ports.
One exception: Because the ALR is set up to forward STP BPDUs only to CPU,
the SW bridge should flood STP BPDUs if local STP is not enabled.
This is archived by not setting skb->offload_fwd_mark on STP BPDUs.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
STP BPDUs arriving on user ports must sent to CPU port only,
for processing by the SW bridge.
Add an ALR entry with STP state override to fix that.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan9303_xmit_use_arl() introduced in previous patch set is wrong.
The chip flood broadcast and unknown multicast frames. The effect is that
broadcasts and multicasts are duplicated on egress. It is not possible to
configure the chip to direct unknown multicasts to CPU port only.
This means that only unicast frames can be transmitted using ALR lookup.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that slave dsa_port always have their name set, there is no need to
pass it to dsa_slave_create() anymore. Remove this argument.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get the optional "label" property and assign a default one directly at
parse time instead of doing it when creating the slave.
For legacy, simply assign the port name stored in cd->port_names.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fetching the master device can be done directly when a port is parsed
from device tree or pdata, instead of waiting until dsa_dst_parse.
Now that -EPROBE_DEFER is returned before we add the switch to the tree,
there is no need to check for this error after dsa_dst_parse.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assign a port's type at parsed time instead of waiting for the tree to
be completed.
Because this is now done earlier, we can use the port's type in
dsa_port_is_* helpers instead of digging again in topology description.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add symmetrical DSA port parsing functions for pdata and device tree,
used to parse and validate a given port node or platform data.
They don't do much for the moment but will be extended later on to
assign a port type and get device references.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point into hiding the -EINVAL error code in ERR_PTR from a
dsa_get_ports function, simply get the "ports" node directly from within
the dsa_parse_ports_dn function.
This also has the effect to make the pdata and device tree handling code
symmetrical inside _dsa_register_switch.
At the same time, rename dsa_parse_ports_dn to dsa_parse_ports_of
because _of is a more common suffix for device tree parsing functions.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts here.
NFP driver bug fix adding nfp_netdev_is_nfp_repr() check to
nfp_fl_output() needed some adjustments because the code block is in
an else block now.
Parallel additions to net/pkt_cls.h and net/sch_generic.h
A bug fix in __tcp_retransmit_skb() conflicted with some of
the rbtree changes in net-next.
The tc action RCU callback fixes in 'net' had some overlap with some
of the recent tcf_block reworking.
Signed-off-by: David S. Miller <davem@davemloft.net>
The new bindings (dsa2.c) and the old bindings (legacy.c) share two
helpers dsa_cpu_dsa_setup and dsa_cpu_dsa_destroy, used to register or
deregister a fixed PHY if a given port has a corresponding device node.
Unclutter the code by moving them into two new port.c helpers,
dsa_port_fixed_link_register_of and dsa_port_fixed_link_(un)register_of.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that DSA core provides port types, there is no need to keep this
information at the switch level. This is a static information that is
part of a DSA core dsa_port structure. Remove them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an enumerated type for ports, which will be way more explicit
to identify a port type instead of digging into switch port masks.
A port can be of type CPU, DSA, user, or unused by default. This is a
static parsed information that cannot be changed at runtime.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a dsa_user_ports() helper to return the ds->enabled_port_mask
mask which is more explicit. This will also minimize diffs when touching
this internal mask.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the DSA code still check ds->enabled_port_mask directly to
inspect a given port type instead of using the provided dsa_is_user_port
helper. Change this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CPU transmit directly to port using tag, the LAN9303 does not
learn MAC addresses received on the CPU port into the ALR.
ALR learning is performed only when transmitting using ALR lookup.
Solution:
If the two external ports are bridged and the packet is not STP BPDU,
then use ALR lookup to allow ALR learning on CPU port.
Otherwise transmit directly to port with STP state override.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the code that tried to identify if a PHY designated by Device
Tree required diversion through the DSA-created MDIO bus. This was
created mainly for the bcm_sf2.c driver back when it did not have its
own MDIO bus driver, which it now has since 461cd1b03e ("net: dsa:
bcm_sf2: Register our slave MDIO bus").
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Martin Hundebøll <mnhu@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The unapply functions are called on the error path.
As for dsa_port_mask, enabled_port_mask and cpu_port_mask won't be used
after so there's no need to unmask the corresponding port bit from them.
This makes dsa_cpu_port_unapply() and dsa_dsa_port_unapply() identical,
which can be factorized later.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The legacy code does not unmask the cpu_port_mask and dsa_port_mask as
stated. But this is done on the error path and those masks won't be used
after that. So instead of fixing the bit operation, simply remove it.
Fixes: 83c0afaec7 ("net: dsa: Add new binding implementation")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of pdata, the dsa_cpu_parse function calls dev_put() before
making sure it isn't NULL. Fix this.
Fixes: 71e0bbde0d ("net: dsa: Add support for platform data")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers are converted to use block callbacks for TC_SETUP_CLS*.
So it is now safe to remove the calls to ndo_setup_tc from cls_*
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benefit from the newly introduced block callback infrastructure and
convert ndo_setup_tc calls for matchall offloads to block callbacks.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_port structure has a "netdev" member, which can be used for
either the master device, or the slave device, depending on its type.
It is true that today, CPU port are not exposed to userspace, thus the
port's netdev member can be used to point to its master interface.
But it is still slightly confusing, so split it into more explicit
"master" and "slave" members inside an anonymous union.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_master_get_slave is slightly confusing since the idiomatic "get"
term often suggests reference counting, in symmetry to "put".
Rename it to dsa_master_find_slave to make the look up operation clear.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many part of the DSA slave code require to get the master device
assigned to a slave device. Remove dsa_master_netdev() in favor of a
dsa_slave_to_master() helper which does that.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many portions of DSA core code require to get the dsa_port structure
corresponding to a slave net_device. For this purpose, introduce a
dsa_slave_to_port() helper.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both DSA slave create and destroy functions call call_dsa_notifiers with
respectively DSA_PORT_REGISTER and DSA_PORT_UNREGISTER and the same
dsa_notifier_register_info structure.
Wrap this in a dsa_slave_notify helper so prevent cluttering these
functions.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dsa_slave_create is called, the related port already has a CPU port
assigned to it, available in its cpu_dp member. Use it instead of the
unique tree cpu_dp.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there is no user for the .set_addr function, remove it from
DSA. If a switch supports this feature (like mv88e6xxx), the
implementation can be done in the driver setup.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to tell the DSA master network device doing the actual
transmission what the desired switch port and queue number is for it to
resolve that to the internal transmit queue it is mapped to.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for communicating a given DSA network device's port
number and switch index, create a specialized DSA notifier and two
events: DSA_PORT_REGISTER and DSA_PORT_UNREGISTER that communicate: the
slave network device (slave_dev), port number and switch number in the
tree.
This will be later used for network device drivers like bcmsysport which
needs to cooperate with its DSA network devices to set-up queue mapping
and scheduling.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the dsa_ptr is a dsa_port instance, there is no need to keep
the tag operations in the dsa_switch_tree structure. Remove it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With DSA, a master net device (CPU facing interface) has a dsa_ptr
pointer to which hangs a dsa_switch_tree. This is not correct because a
master interface is wired to a dedicated switch port, and because we can
theoretically have several master interfaces pointing to several CPU
ports of the same switch fabric.
Change the master interface's dsa_ptr for the CPU dsa_port pointer.
This is a step towards supporting multiple CPU ports.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to make DSA master devices point to their corresponding
CPU port instead of the whole tree, add copies of dst and rcv in the
dsa_port structure so that we keep fast access in the receive hot path.
Also keep the copies at the beginning of the dsa_port structure in order
to ensure they are available in cacheline 1.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA tagging protocol operations are specific to each CPU port,
thus the dsa_device_ops pointer belongs to the dsa_port structure.
>From now on assign a slave's xmit copy from its CPU port tagging
operations. This will ease the future support for multiple CPU ports.
Also keep the tag_ops at the beginning of the dsa_port structure so that
we ensure copies for hot path are in cacheline 1.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When resolving the DSA tagging protocol used by a CPU switch, use a
temporary "tag_ops" variable to store the dsa_device_ops instead of
using directly dst->tag_ops. This will make the future patches moving
this pointer around easier to read.
There is no functional changes.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it clear that the master device is linked to a CPU port by using
"cpu_dp" for the dsa_port variable in master.c instead of "port", then
use a "port" variable to describe the port index, as usually seen in
other places of DSA core.
This will make the future patch touching dsa_ptr more readable. There is
no functional changes.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA tagging code does not need to know about the DSA architecture,
it only needs to return the slave device corresponding to the source
port index (and eventually the source device index for cascade-capable
switches) parsed from the frame received on the master device.
For this purpose, provide an inline dsa_master_get_slave helper which
validates the device and port indexes and look up the slave device.
This makes the tagging rcv functions more concise and robust, and also
makes dsa_get_cpu_port obsolete.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We cannot be registering the network device first, then setting its
carrier off and finally connecting it to a PHY, doing that leaves a
window during which the carrier is at best inconsistent, and at worse
the device is not usable without a down/up sequence since the network
device is visible to user space with possibly no PHY device attached.
Re-order steps so that they make logical sense. This fixes some devices
where the port was not usable after e.g: an unbind then bind of the
driver.
Fixes: 0071f56e46 ("dsa: Register netdev before phy")
Fixes: 91da11f870 ("net: Distributed Switch Architecture protocol support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_ethtool_nway_reset now that dsa_slave_nway_reset does exactly
the same.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_ethtool_set_link_ksettings now that dsa_slave_set_link_ksettings
does exactly the same.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_ethtool_get_link_ksettings now that dsa_slave_get_link_ksettings
does exactly the same.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to store a phy_device in dsa_slave_priv since
net_device already provides one. Simply s/p->phy/dev->phydev/.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of returning -EOPNOTSUPP when a slave device has no PHY,
directly return -ENODEV as ethtool and phylib do.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide dsa_port_enable and dsa_port_disable helpers to respectively
enable and disable a switch port. This makes the dsa_port_set_state_now
helper static.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA slave open function configures the unicast MAC addresses on the
master device, enable the switch port, change its STP state, then start
the PHY device.
Make the close function symmetric, by first stopping the PHY device,
then changing the STP state, disabling the switch port and restore the
master device.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso