This patch fixes/cleans up the loading of the firmware file when the
driver is loaded and initialized.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch implements the xc4000_sleep() function.
The 'no_powerdown' module parameter is now interpreted differently:
- 0 uses a device-specific default
- 1 disables power management like before
- 2 enables power management
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for selecting a card type in struct
xc4000_config, to allow for implementing some card specific code
in the driver.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch makes the following fixes in check_firmware():
- there is only one BASE and INIT1 firmware for XC4000
- loading SCODE is needed also for FM radio
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Removed unused code from load_scode() (all SCODE firmwares are
assumed to have the HAS_IF bit set).
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The firmware_name module parameter makes it possible to set the firmware
file name. It defaults to "xc4000.fw" if not specified.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The xc_get_frequency_error() function reported the frequency error
incorrectly. The data read from the hardware is a signed integer, in
15625 Hz units. The attached patch fixes the bug.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a mutex to xc4000_priv, to protect the driver
from being accessed by multiple processes at the same time.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch implements support for DVB-T with 7 MHz bandwidth.
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch makes the following changes to the standards table:
- added 'u16 int_freq' to struct XC_TV_STANDARD (needed for analog TV
and radio, 0 for DVB-T)
- added new standard for SECAM-D/K video with PAL-D/K audio
- the 'int_freq' values are now specified in the table
- changed VideoMode for NTSC and PAL-B/G standards
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the first of a set of patches that update the original xc4000
sources to my modified version. It removes some unused code, and makes
a few minor formatting changes.
[mchehab@redhat.com: re-add XC_TUNE_ANALOG/XC_TUNE_DIGITAL constants, to avoid compilation breakage]
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove some inline comments I had written from when I was computing the proper
dib7000p configuration to work with the xc4000.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove some printk() calls added during driver development, and demote some
other messages to debug only (to reduce dmesg chatter).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Give the xc4000 firmware filename a filename that makes more sense for public
release.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't dump debug into to dmesg by default (something I had enabled during
bringup of the xc4000 driver).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixup the PLL and AGC configs so that the 340e works (correcting errors I made
when I did the original config blindly).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove a hack I had put in to force the firmware to be 8MHz, now setting
the firmware properly based on the target standard.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Based on a reference trace under Windows, reverse engineer the PLL config.
Note that the xtal is not yet setup, and the timf cannot be determined yet
because my reference trace doesn't actually achieve a signal lock.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It was confirmed by DibCom that i2c stretching is broken in the i2c master
on the dib7700. So we need to put a hack into the xc4000 driver to not
complain in certain very specific cases where we know i2c stretching occurs.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Setup a proper AGC config for the 340e, based on the Windows USB trace
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove hard-coded references to 5400, using the value passed in when the
xc4000 is attached.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Properly setup the standard firmware loading and scode loading, as well as
getting rid of a ton of dead code. Note that I am getting a single i2c
error when the standard firmware sets the video standard, but everything else
seems to be loading properly now.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add code to handle firmware blobs for the standard and scode. Note there
appears to be some issue with loading the DTV8 standard firmware, probably
related to direct/indirect mode.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since we use the xc3028 version of the firmware file parsing routine (which
includes support for scodes and separate blobs), we can drop the xc5000
version of the code.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The xc4000 driver is based on the original xc5000 driver, and while the
xc5000 supports the XREG_BUSY register, the xc4000 does not. So remove the
code in question.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need to set the firmware type properly in order to locate the init1
firmware.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The xc3028 version does i2c splitting in a different manner than xc4000 and
xc5000, so reuse the xc5000 version of the routine (the key here being that
xc4000 expects the first *two* bytes to be the same for splitting transactions.
Doing it the xc3028 way was resulting in i2c errors partially through the
firmware load. With this change, it would appear that the entire base firmware
is being loaded successfully (product id now properly shows 0x0FA0).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Switch over to using the firmware management routines from the tuner-xc2028,
since that has support for scodes, etc.
This code still requires signficant cleanup, and at this point the base
firmware does not load properly (i2c write errors about 300 bytes in).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need to set the dev.parent member on the dib7000p on its i2c master, or
else calls to request_firmware() will hit an oops in 2.6.31.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a sleep since in some cases the dib7000p wasn't online when being probed.
The optimal timing has not yet been determined.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the correct i2c bus to communicate with the tuner, and properly setup the
reset GPIO and i2c address.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Provide a frontend setup routine for the PCTV 340e which takes into account
the specific GPIO setup of the board.
Note that this patch does *not* take into account the xc4000 reset pin, which
is attached to the dib7000.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the board profile for the PCTV 340eSE, since that's what I have here
for development.
[mchehab@redhat.com: rebased on the top of the current tree]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is initial code written by Davide Ferri for the PCTV 340e, including
a new xc4000 driver. I am checking in all the code unmodified, and making
no assertions about its quality (other than confirming it compiles).
[mchehab@redhat.com: rebased on the top of the current tree]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Davide Ferri <davidef1986@gmail.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The implementation of the gain calculation for this sensor is incorrect.
It is only working for the first 127 values.
The reason is, that the gain cannot be set directly by writing a value
into the gain registers of the sensor. The gain register work this way
(see datasheet page 24): bits 0 to 6 are called "initial gain". These
are linear. But bits 7 and 8 ("analog multiplicative factors") and bits
9 and 10 ("digital multiplicative factors") work completely different:
Each of these bits increase the gain by the factor 2. So if the bits
7-10 are 0011, 0110, 1100 or 0101 for example, the gain from bits 0-6 is
multiplied by 4. The order of the bits 7-10 is not important for the
resulting gain. (But there are some recommended values for low noise)
The current driver doesn't do this correctly: If the current gain is 000
0111 1111 (127) and the gain is increased by 1, you would expect the
image to become brighter. But the image is completly dark, because the
new gain is 000 1000 0000 (128). This means: Initial gain of 0,
multiplied by 2. The result is 0.
This patch adds a new function which does the gain calculation and also
fixes the same bug for red_balance and blue_balance. Additionally, the
driver follows the recommendation from the datasheet, which says, that
the gain should always be above 0x0020.
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Johannes Obermaier <johannes.obermaier@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are problems when you use this camera/sensor in a very bright room
or outside. The image is completely white, because it is overexposed.
The driver uses a default value which is not suitable for all
environments.
This patch makes it possible to adjust the exposure time by youself. I
found out by logging the i2c-data, that the windows driver for this
sensor is doing this, too. I tested the camera on a sunny day and after
adjusting the exposure time, I was able to see a very good image.
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Johannes Obermaier <johannes.obermaier@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to the datasheet (page 8), the first optical clear
pixel-column is not at position 14. The correct/recommended value is 20.
Without this patch there is a dark line on the left side of the image.
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Johannes Obermaier <johannes.obermaier@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The conversion of winbond-cir to use rc-core seems to have missed a
a few bits and pieces which were in my local tree. Kudos to
Juan Jesús García de Soria Lucena <skandalfo@gmail.com> for noticing.
[mchehab@redhat.com: fix two UTF-8 violations]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the original code, if the allocation failed we dereference "rr3"
when it was NULL.
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If change_protocol() fails and we goto out_raw, then it calls unlock
twice. I noticed that the other time we called change_protocol() we
held the &dev->lock, so I changed it to hold it here too.
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Otherwise they clutter the dmesg buffer even on a production kernel.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The function "rc5_scan" in "dvb_usb.h" is returning invalid value.
The value should be returned "u16" but is returning "u8".
See example below in "drivers/media/dvb/dvb-usb/opera1.c":
send_key = (send_key & 0xffff) | 0x0100;
for (i = 0; i < ARRAY_SIZE(rc_map_opera1_table); i++) {
if (rc5_scan(&rc_map_opera1_table[i]) == (send_key & 0xffff)) {
*state = REMOTE_KEY_PRESSED;
*event = rc_map_opera1_table[i].keycode;
opst->last_key_pressed =
rc_map_opera1_table[i].keycode;
break;
}
opst->last_key_pressed = 0;
}
Signed-off-by: Manoel Pinheiro <pinusdtv@hotmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert radio-sf16fmr2 to use generic TEA575x implementation. Most of the
driver code goes away as SF16-FMR2 is basically just a TEA5757 tuner
connected to ISA bus.
The card can optionally be equipped with PT2254A volume control (equivalent
of TC9154AP) - the volume setting is completely reworked (with balance control
added) and tested.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The info and err macros are already defined by the USB stack. Rename
these macros to avoid macro redefinition warnings.
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The dbg, warn and info macros are already defined by the USB stack.
Rename these macros to avoid macro redefinition warnings.
Refactor lineshift in printouts.
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
radio->int_in_urb is not deallocated on error paths in si470x_usb_driver_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>