The PAMU caches use the LIODNs to determine which cache lines hold the
entries for the corresponding LIODs. The LIODNs must therefore be
carefully assigned to avoid cache thrashing -- two active LIODs with
LIODNs that put them in the same cache line.
Currently, LIODNs are statically assigned by U-Boot, but this has
limitations. LIODNs are assigned even for devices that may be disabled
or unused by the kernel. Static assignments also do not allow for device
drivers which may know which LIODs can be used simultaneously. In
other words, we really should assign LIODNs dynamically in Linux.
To do that, we need to describe the PAMU device and cache topologies in
the device trees.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Stuart Yoder <stuart.yoder@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This new property defines the era of the particular SEC version.
The compatible property in device tree "crypto" node has been updated
not to contain SEC era numbers.
Signed-off-by: Vakul Garg <vakul@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
By moving the two JP12 jumpers 90 degrees, and switching the
setting of SW2.8, the sbc8548 can be configured to boot off
the alternate 64MB SODIMM, which when populated with u-boot
can be a handy recovery option, in case the u-boot in the
8MB soldered on flash gets corrupted. Here we add an alternate
dts file to match that configuration.
To better highlight the differences, the output from the u-boot
"fli" command is shown for the normal configuration and then
the alternate configuration.
Normal:
-----------------------
Bank # 1: CFI conformant flash (8 x 8) Size: 8 MB in 64 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x17
Erase timeout: 4096 ms, write timeout: 1 ms
Buffer write timeout: 2 ms, buffer size: 32 bytes
Sector Start Addresses:
FF800000 E FF820000 E FF840000 E FF860000 E FF880000 E
[...]
FFEE0000 E FFF00000 E FFF20000 E FFF40000 E FFF60000 E
FFF80000 FFFA0000 RO FFFC0000 RO FFFE0000 RO
Bank # 2: CFI conformant flash (32 x 8) Size: 64 MB in 128 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x18
Erase timeout: 4096 ms, write timeout: 1 ms
Buffer write timeout: 2 ms, buffer size: 32 bytes
Sector Start Addresses:
EC000000 E EC080000 E EC100000 E EC180000 E EC200000 E
[...]
EFC00000 E EFC80000 E EFD00000 E EFD80000 E EFE00000 E
EFE80000 E EFF00000 EFF80000
-----------------------
Alternate:
-----------------------
Bank # 1: CFI conformant flash (32 x 8) Size: 64 MB in 128 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x18
Erase timeout: 4096 ms, write timeout: 1 ms
Buffer write timeout: 2 ms, buffer size: 32 bytes
Sector Start Addresses:
FC000000 E FC080000 E FC100000 E FC180000 E FC200000 E
[...]
FFC00000 E FFC80000 E FFD00000 E FFD80000 E FFE00000 E
FFE80000 E FFF00000 RO FFF80000 RO
Bank # 2: CFI conformant flash (8 x 8) Size: 8 MB in 64 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x17
Erase timeout: 4096 ms, write timeout: 1 ms
Buffer write timeout: 2 ms, buffer size: 32 bytes
Sector Start Addresses:
EF800000 E EF820000 E EF840000 E EF860000 E EF880000 E
[...]
EFEE0000 E EFF00000 E EFF20000 E EFF40000 E EFF60000 E
EFF80000 E EFFA0000 EFFC0000 EFFE0000
-----------------------
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The original memory map for the sbc8548 had the 64MB SODIMM flash
device misaligned by 8MB to allow a window of address space for
the soldered on 8MB device -- i.e.
start end CS<n> width Desc.
----------------------------------------------------------
fb80_0000 ff7f_ffff CS6 32 SODIMM flash (64MB)
ff80_0000 ffff_ffff CS0 8 Boot flash (8MB)
However, if we want to change the configuration so that it boots
off the 64MB flash, it is in turn then aligned with a 64MB boundary,
starting at fc00_0000 (and the 8MB @ fb80_0000 -> fbff_ffff).
This makes for complicated updates, since what is the beginning
of the physical device is 8MB into its address space in the default
configuration shown above.
This issue was fixed as of u-boot commit 3fd673cf363bc86ed42eff713d4
("sbc8548: relocate 64MB user flash to sane boundary") -- in which
the SODIMM was mapped to ec00_0000 (natively aligned under efff_ffff)
and so when JP12/SW2.8 are switched, it will be a a simple 0xec --> 0xfc
mapping between the two instances.
Here we make the associated changes in the localbus flash memory
map in the dts file: indicating the 64MB device starts at ec00_0000
and that the tail end of the 64MB device (last 2 sectors) can contain
a bootloader image.
The partitions for both flash devices get a clean-up; there were
non-meaningful assignments in there that probably originated from
the MPC8548CDS on which the file was based on. Now there is just
the categorization of free space and bootloader images.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Updates to u-boot allow this board to boot off of either
the 8MB soldered on flash, or the 64MB SODIMM flash.
This is achieved by changing JP12 and SW2.8 which in turn
swaps which flash device appears on /CS0 and /CS6 respectively.
Since the flash devices are not the same size, this also
changes the MTD memory map layout on the local bus.
Here we split the common chunks out into a pre and post
include, so they can be reused by an upcoming "alternative
boot" dts file; leaving only the local bus chunk behind.
No content changes are made at this point - it is just purely
the move to using include files.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use for_each_compatible_node() macro instead of open coding it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
arch/powerpc/sysdev/fsl_msi.c:31:1: warning: symbol 'msi_head' was not declared. Should it be static?
arch/powerpc/sysdev/fsl_msi.c:138:40: warning: incorrect type in argument 1 (different base types)
arch/powerpc/sysdev/fsl_msi.c:138:40: expected restricted __be64 const [usertype] *p
arch/powerpc/sysdev/fsl_msi.c:138:40: got unsigned long long const [usertype] *[assigned] reg
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
arch/powerpc/sysdev/fsl_lbc.c:77:36: warning: incorrect type in initializer (different base types)
arch/powerpc/sysdev/fsl_lbc.c:77:36: expected restricted __be32 [usertype] br
arch/powerpc/sysdev/fsl_lbc.c:77:36: got unsigned int
arch/powerpc/sysdev/fsl_lbc.c:78:36: warning: incorrect type in initializer (different base types)
arch/powerpc/sysdev/fsl_lbc.c:78:36: expected restricted __be32 [usertype] or
arch/powerpc/sysdev/fsl_lbc.c:78:36: got unsigned int
arch/powerpc/sysdev/fsl_lbc.c:80:21: warning: restricted __be32 degrades to integer
arch/powerpc/sysdev/fsl_lbc.c:80:38: warning: restricted __be32 degrades to integer
arch/powerpc/sysdev/fsl_lbc.c:111:12: warning: incorrect type in assignment (different base types)
arch/powerpc/sysdev/fsl_lbc.c:111:12: expected restricted __be32 [usertype] br
arch/powerpc/sysdev/fsl_lbc.c:111:12: got unsigned int
arch/powerpc/sysdev/fsl_lbc.c:113:17: warning: restricted __be32 degrades to integer
arch/powerpc/sysdev/fsl_lbc.c:127:17: warning: restricted __be32 degrades to integer
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for enabling and context switching the Target
Address Register in Power8. The TAR is a new special purpose register
that can be used for computed branches with the bctar[l] (branch
conditional to TAR) instruction in the same manner as the count and link
registers.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pseries/iommu: remove DDW on kexec
We currently insert a property in the device-tree when we successfully
configure DDW for a given slot. This was meant to be an optimization to
speed up kexec/kdump, so that we don't need to make the RTAS calls again
to re-configured DDW in the new kernel.
However, we end up tripping a plpar_tce_stuff failure on kexec/kdump
because we unconditionally parse the ibm,dma-window property for the
node at bus/dev setup time. This property contains the 32-bit DMA window
LIOBN, which is distinct from the DDW window's. We pass that LIOBN (via
iommu_table_init -> iommu_table_clear -> tce_free ->
tce_freemulti_pSeriesLP) to plpar_tce_stuff, which fails because that
32-bit window is no longer present after
25ebc45b93 ("powerpc/pseries/iommu: remove
default window before attempting DDW manipulation").
I believe the simplest, easiest-to-maintain fix is to just change our
initcall to, rather than detecting and updating the new kernel's DDW
knowledge, just remove all DDW configurations. When the drivers
re-initialize, we will set everything back up as it was before.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The parameter is unused, and complicates a following fix. Just remove
it.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It seems, we're fine with just annotating the two functions.
Thus, this fixes the following build warnings on ppc64:
WARNING: arch/powerpc/sysdev/xics/built-in.o(.text+0x1664):
The function .ics_rtas_init() references
the function __init .xics_register_ics().
This is often because .ics_rtas_init lacks a __init
annotation or the annotation of .xics_register_ics is wrong.
WARNING: arch/powerpc/sysdev/built-in.o(.text+0x6044):
The function .ics_rtas_init() references
the function __init .xics_register_ics().
This is often because .ics_rtas_init lacks a __init
annotation or the annotation of .xics_register_ics is wrong.
WARNING: arch/powerpc/kernel/built-in.o(.text+0x2db30):
The function .start_secondary() references
the function __cpuinit .vdso_getcpu_init().
This is often because .start_secondary lacks a __cpuinit
annotation or the annotation of .vdso_getcpu_init is wrong.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are now two kinds of DMA windows that might be presented by
PowerVM DDW support -- huge windows (that can map all of system memory
regardless of the LPAR configuration) and non-huge windows (which
can't). They are implemented slightly differently in PowerVM, and thus
have different characteristics. The most obvious is that slot isolate
doesn't clear the TCEs/window for us with non-huge windows. Thus, when a
DLPAR operation occurs on a slot using a non-huge window, TCEs are still
present (the notifier chain doesn't currently remove them explicitly)
and the DLPAR fails. Fix this by calling remove_ddw() first, which will
unmap the DDW TCEs.
Note: a corresponding change to drmgr is needed to actually successfully
DLPAR, such that the device-tree update (which causes the notifier chain
to fire) occurs before slot isolate.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
tce_clearrange_multi_pSeriesLP is attempting to iterate over all TCEs in
a given range. However, is it not advancing the dma_offset value passed
to plpar_tce_stuff via the next value. This prevents DLPAR from
completing, because TCEs are still present at slot isolation time.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Change the hardware breakpoint code so that we can support wider ranged
breakpoints.
This means both ptrace and perf hardware breakpoints can use upto 512 byte long
breakpoints when using the DAWR and only 8 byte when using the DABR.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we set the length field in the DAWR to 0 which defaults it to one
double word (64bits) which is the same as the DABR.
Change this so that we can set it to longer values as supported by the DAWR.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
perf/Power: PERF_EVENT_IOC_ENABLE does not reenable event
If we disable a perf event because we exceeded the specified ->event_limit,
power_pmu_stop() sets the PERF_HES_STOPPED flag on the event.
If the application then re-enables the event using PERF_EVENT_IOC_ENABLE
ioctl, we don't ever clear this STOPPED flag. Consequently, the user space
is never notified of the event.
Following message has more background and test case.
http://lists.eecs.utk.edu/pipermail/ptools-perfapi/2012-October/002528.html
Used the following test cases to verify that this patch works on latest PAPI.
$ papi.git/src/ctests/nonthread PAPI_TOT_CYC@5000000
$ papi.git/src/ctests/overflow_single_event
Changelog[v2]:
- [Paul Mackerras] Also clear PERF_HES_UPTODATE flag since we are
restarting the event; cleanup comments and patch description.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use local_paca directly in macro SHARED_PROCESSOR, as all processors
have the same value for the field shared_proc, so we don't need care
racy here.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Uprobes uses emulate_step in sstep.c, but we haven't explicitly specified
the dependency. On pseries HAVE_HW_BREAKPOINT protects us, but 44x has no
such luxury.
Consolidate other users that depend on sstep and create a new config option.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: linuxppc-dev@ozlabs.org
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CTS-1000 is based on P4080. GPIO 27 is used to signal the FPGA to
switch off power, and also associates IRQ 8 with front-panel button
press (which we use to call orderly_poweroff()).
The relevant device-tree looks like this:
gpio0: gpio@130000 {
compatible = "fsl,qoriq-gpio";
reg = <0x130000 0x1000>;
interrupts = <55 2 0 0>;
#gpio-cells = <2>;
gpio-controller;
/* Allows powering off the system via GPIO signal. */
gpio-halt@27 {
compatible = "sgy,gpio-halt";
gpios = <&gpio0 27 0>;
interrupts = <8 1 0 0>;
};
};
Because the driver cannot match on sgy,gpio-halt (because the node is never
processed through of_platform), it matches on fsl,qoriq-gpio and then
checks child nodes for the matching sgy,gpio-halt. This also ensures that
the GPIO controller is detected prior to sgy_cts1000's probe callback,
since that node wont match via of_platform until the controller is
registered.
Also, because the GPIO handler for triggering system poweroff might sleep,
the IRQ uses a workqueue to call orderly_poweroff().
As a final note, this driver may be expanded for other features specific to
the CTS-1000.
Signed-off-by: Ben Collins <ben.c@servergy.com>
Cc: Jack Smith <jack.s@servergy.com>
Cc: Vihar Rai <vihar.r@servergy.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
While this should be harmless now that distribute_irqs
obeys MPIC_SINGLE_DEST_CPU, there's no reason to enable this
on mpc85xx/mpc86xx since MPIC_SINGLE_DEST_CPU will always be set.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Previously we were setting an illegal configuration on mpc85xx
MPICs if CONFIG_IRQ_ALL_CPUS is enabled (which for some reason it is
in mpc85xx_smp_defconfig).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have a mix of decimal and hex here, so lets make them consistently
hex. Also, strace will print them in hex if it can't decode them, so
having them in hex here makes it easier to match up.
No functional change.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The only persistent change made by this loop is calling
memblock_set_node() once for each memblock, which is not useful (and has
no effect) as memblock_set_node() is not called with any
memblock-specific parameters.
Subsistute a single memblock_set_node().
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With lazy interrupt, we always call __check_irq_replaysome with
decrementers_next_tb to check if we need to replay timer interrupt.
So in hotplug case we also need to set decrementers_next_tb as MAX
to make sure __check_irq_replay don't replay timer interrupt
when return as we expect, otherwise we'll trap here infinitely.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
the variable backup_current_thread_info isn't freed before existing the
function.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In preempt case current arch_local_irq_restore() from
preempt_schedule_irq() may enable hard interrupt but we really
should disable interrupts when we return from the interrupt,
and so that we don't get interrupted after loading SRR0/1.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The calculation for the left shift of the mask OPROFILE_PM_PMCSEL_MSK has an
error. The calculation is should be to shift left by (max_cntrs - cntr) times
the width of the pmsel field width. However, the #define OPROFILE_MAX_PMC_NUM
was used instead of OPROFILE_PMSEL_FIELD_WIDTH. This patch fixes the
calculation.
Signed-off-by: Carl Love <cel@us.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
commit f96972f2dc "kernel/sys.c: call disable_nonboot_cpus() in
kernel_restart()"
added a call to disable_nonboot_cpus() on kernel_restart(), which tries
to shutdown all the CPUs except the first one. The issue with the PA
Semi, is that it does not support CPU hotplug.
When the call is made to __cpu_down(), it calls the notifiers
CPU_DOWN_PREPARE, and then tries to take the CPU down.
One of the notifiers to the CPU hotplug code, is the cpufreq. The
DOWN_PREPARE will call __cpufreq_remove_dev() which calls
cpufreq_driver->exit. The PA Semi exit handler unmaps regions of I/O
that is used by an interrupt that goes off constantly
(system_reset_common, but it goes off during normal system operations
too). I'm not sure exactly what this interrupt does.
Running a simple function trace, you can see it goes off quite a bit:
# tracer: function
#
# TASK-PID CPU# TIMESTAMP FUNCTION
# | | | | |
<idle>-0 [001] 1558.859363: .pasemi_system_reset_exception <-.system_reset_exception
<idle>-0 [000] 1558.860112: .pasemi_system_reset_exception <-.system_reset_exception
<idle>-0 [000] 1558.861109: .pasemi_system_reset_exception <-.system_reset_exception
<idle>-0 [001] 1558.861361: .pasemi_system_reset_exception <-.system_reset_exception
<idle>-0 [000] 1558.861437: .pasemi_system_reset_exception <-.system_reset_exception
When the region is unmapped, the system crashes with:
Disabling non-boot CPUs ...
Error taking CPU1 down: -38
Unable to handle kernel paging request for data at address 0xd0000800903a0100
Faulting instruction address: 0xc000000000055fcc
Oops: Kernel access of bad area, sig: 11 [#1]
PREEMPT SMP NR_CPUS=64 NUMA PA Semi PWRficient
Modules linked in: shpchp
NIP: c000000000055fcc LR: c000000000055fb4 CTR: c0000000000df1fc
REGS: c0000000012175d0 TRAP: 0300 Not tainted (3.8.0-rc4-test-dirty)
MSR: 9000000000009032 <SF,HV,EE,ME,IR,DR,RI> CR: 24000088 XER: 00000000
SOFTE: 0
DAR: d0000800903a0100, DSISR: 42000000
TASK = c0000000010e9008[0] 'swapper/0' THREAD: c000000001214000 CPU: 0
GPR00: d0000800903a0000 c000000001217850 c0000000012167e0 0000000000000000
GPR04: 0000000000000000 0000000000000724 0000000000000724 0000000000000000
GPR08: 0000000000000000 0000000000000000 0000000000000001 0000000000a70000
GPR12: 0000000024000080 c00000000fff0000 ffffffffffffffff 000000003ffffae0
GPR16: ffffffffffffffff 0000000000a21198 0000000000000060 0000000000000000
GPR20: 00000000008fdd35 0000000000a21258 000000003ffffaf0 0000000000000417
GPR24: 0000000000a226d0 c000000000000000 0000000000000000 0000000000000000
GPR28: c00000000138b358 0000000000000000 c000000001144818 d0000800903a0100
NIP [c000000000055fcc] .set_astate+0x5c/0xa4
LR [c000000000055fb4] .set_astate+0x44/0xa4
Call Trace:
[c000000001217850] [c000000000055fb4] .set_astate+0x44/0xa4 (unreliable)
[c0000000012178f0] [c00000000005647c] .restore_astate+0x2c/0x34
[c000000001217980] [c000000000054668] .pasemi_system_reset_exception+0x6c/0x88
[c000000001217a00] [c000000000019ef0] .system_reset_exception+0x48/0x84
[c000000001217a80] [c000000000001e40] system_reset_common+0x140/0x180
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch fixes MAX_STACK_TRACE_ENTRIES too low warning for ppc32,
which is similar to commit 12660b17.
Reported-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Tested-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
One fix for the AMD IOMMU driver to work around broken BIOSes found in
the field. Some BIOSes forget to enable a workaround for a hardware
problem which might cause the IOMMU to stop working under high load
conditions. The fix makes sure this workaround is enabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=X83i
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fix from Joerg Roedel:
"One fix for the AMD IOMMU driver to work around broken BIOSes found in
the field. Some BIOSes forget to enable a workaround for a hardware
problem which might cause the IOMMU to stop working under high load
conditions. The fix makes sure this workaround is enabled."
* tag 'iommu-fixes-v3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
IOMMU, AMD Family15h Model10-1Fh erratum 746 Workaround
We have some build failure fixes (twl4030, vexpress, abx500 and tps65910),
some actual runtime oops and lockup fixes (rtsx, da9052), and some more
hypothetical NULL pointers dereferences fixes for pcf50633 and max776xx.
Then we also have additional rtsx fixes for a correct switch output voltage
and clock divider correctness for rtl8411 (rtsx driver), and irqdomain fix for
db8550-prcmu, and some more cosmetic fixes for arizona and wm5102.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=rxug
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD fixes from Samuel Ortiz:
"This is the first pull request for MFD fixes for 3.8
We have some build failure fixes (twl4030, vexpress, abx500 and
tps65910), some actual runtime oops and lockup fixes (rtsx, da9052),
and some more hypothetical NULL pointers dereferences fixes for
pcf50633 and max776xx.
Then we also have additional rtsx fixes for a correct switch output
voltage and clock divider correctness for rtl8411 (rtsx driver), and
irqdomain fix for db8550-prcmu, and some more cosmetic fixes for
arizona and wm5102."
* tag 'mfd-for-linus-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: rtsx: Fix oops when rtsx_pci_sdmmc is not probed
mfd: wm5102: Fix definition of WM5102_MAX_REGISTER
mfd: twl4030: Don't warn about uninitialized return code
mfd: da9052/53 lockup fix
mfd: rtsx: Add clock divider hook
mmc: rtsx: Call MFD hook to switch output voltage
mfd: rtsx: Add output voltage switch hook
mfd: Fix compile errors and warnings when !CONFIG_AB8500_BM
mfd: vexpress: Export global functions to fix build error
mfd: arizona: Check errors from regcache_sync()
mfd: tc3589x: Use simple irqdomain
mfd: pcf50633: Init pcf->dev before using it
mfd: max77693: Init max77693->dev before using it
mfd: max77686: Init max77686->dev before using it
mfd: db8500-prcmu: Fix irqdomain usage
mfd: tps65910: Select REGMAP_IRQ in Kconfig to fix build error
mfd: arizona: Disable control interface reporting for WM5102 and WM5110
Pull networking updates from David Miller:
"Much more accumulated than I would have liked due to an unexpected
bout with a nasty flu:
1) AH and ESP input don't set ECN field correctly because the
transport head of the SKB isn't set correctly, fix from Li
RongQing.
2) If netfilter conntrack zones are disabled, we can return an
uninitialized variable instead of the proper error code. Fix from
Borislav Petkov.
3) Fix double SKB free in ath9k driver beacon handling, from Felix
Feitkau.
4) Remove bogus assumption about netns cleanup ordering in
nf_conntrack, from Pablo Neira Ayuso.
5) Remove a bogus BUG_ON in the new TCP fastopen code, from Eric
Dumazet. It uses spin_is_locked() in it's test and is therefore
unsuitable for UP.
6) Fix SELINUX labelling regressions added by the tuntap multiqueue
changes, from Paul Moore.
7) Fix CRC errors with jumbo frame receive in tg3 driver, from Nithin
Nayak Sujir.
8) CXGB4 driver sets interrupt coalescing parameters only on first
queue, rather than all of them. Fix from Thadeu Lima de Souza
Cascardo.
9) Fix regression in the dispatch of read/write registers in dm9601
driver, from Tushar Behera.
10) ipv6_append_data miscalculates header length, from Romain KUNTZ.
11) Fix PMTU handling regressions on ipv4 routes, from Steffen
Klassert, Timo Teräs, and Julian Anastasov.
12) In 3c574_cs driver, add necessary parenthesis to "x << y & z"
expression. From Nickolai Zeldovich.
13) macvlan_get_size() causes underallocation netlink message space,
fix from Eric Dumazet.
14) Avoid division by zero in xfrm_replay_advance_bmp(), from Nickolai
Zeldovich. Amusingly the zero check was already there, we were
just performing it after the modulus :-)
15) Some more splice bug fixes from Eric Dumazet, which fix things
mostly eminating from how we now more aggressively use high-order
pages in SKBs.
16) Fix size calculation bug when freeing hash tables in the IPSEC
xfrm code, from Michal Kubecek.
17) Fix PMTU event propagation into socket cached routes, from Steffen
Klassert.
18) Fix off by one in TX buffer release in netxen driver, from Eric
Dumazet.
19) Fix rediculous memory allocation requirements introduced by the
tuntap multiqueue changes, from Jason Wang.
20) Remove bogus AMD platform workaround in r8169 driver that causes
major problems in normal operation, from Timo Teräs.
21) virtio-net set affinity and select queue don't handle
discontiguous cpu numbers properly, fix from Wanlong Gao.
22) Fix a route refcounting issue in loopback driver, from Eric
Dumazet. There's a similar fix coming that we might add to the
macvlan driver as well.
23) Fix SKB leaks in batman-adv's distributed arp table code, from
Matthias Schiffer.
24) r8169 driver gives descriptor ownership back the hardware before
we're done reading the VLAN tag out of it, fix from Francois
Romieu.
25) Checksums not calculated properly in GRE tunnel driver fix from
Pravin B Shelar.
26) Fix SCTP memory leak on namespace exit."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (101 commits)
dm9601: support dm9620 variant
SCTP: Free the per-net sysctl table on net exit. v2
net: phy: icplus: fix broken INTR pin settings
net: phy: icplus: Use the RGMII interface mode to configure clock delays
IP_GRE: Fix kernel panic in IP_GRE with GRE csum.
sctp: set association state to established in dupcook_a handler
ip6mr: limit IPv6 MRT_TABLE identifiers
r8169: fix vlan tag read ordering.
net: cdc_ncm: use IAD provided by the USB core
batman-adv: filter ARP packets with invalid MAC addresses in DAT
batman-adv: check for more types of invalid IP addresses in DAT
batman-adv: fix skb leak in batadv_dat_snoop_incoming_arp_reply()
net: loopback: fix a dst refcounting issue
virtio-net: reset virtqueue affinity when doing cpu hotplug
virtio-net: split out clean affinity function
virtio-net: fix the set affinity bug when CPU IDs are not consecutive
can: pch_can: fix invalid error codes
can: ti_hecc: fix invalid error codes
can: c_can: fix invalid error codes
r8169: remove the obsolete and incorrect AMD workaround
...
The IOMMU may stop processing page translations due to a perceived lack
of credits for writing upstream peripheral page service request (PPR)
or event logs. If the L2B miscellaneous clock gating feature is enabled
the IOMMU does not properly register credits after the log request has
completed, leading to a potential system hang.
BIOSes are supposed to disable L2B micellaneous clock gating by setting
L2_L2B_CK_GATE_CONTROL[CKGateL2BMiscDisable](D0F2xF4_x90[2]) = 1b. This
patch corrects that for those which do not enable this workaround.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joro@8bytes.org>
The recent commit fb6791d100
included the wrong logic. The lvbptr check was incorrectly
added after the patch was tested.
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
dm9620 is a newer variant of dm9601 with more features (usb 2.0, checksum
offload, ..), but it can also be put in a dm9601 compatible mode, allowing
us to reuse the existing driver.
This does mean that the extended features like checksum offload cannot be
used, but that's hardly critical on a 100mbps interface.
Thanks to Sławek Wernikowski <slawek@wernikowski.net> for providing me
with a dm9620 based device to test.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the setting of the INTR pin that is
valid for IP101 A/G device and not for the IP1001.
Reported-by: Anunay Saxena <anunay.saxena@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like several other PHY devices which support RGMII, the IC+1001 allows
additional delays to by added to the RX_CLK and TX_CLK signals to
compensate for skew between the clock and data signals. Previously this
was always enabled, but this change makes use of the different RGMII
interface modes to allow the user to specify whether this should be
enabled.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to IP_GRE GSO support, GRE can recieve non linear skb which
results in panic in case of GRE_CSUM. Following patch fixes it by
using correct csum API.
Bug introduced in commit 6b78f16e4b (gre: add GSO support)
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While sctp handling a duplicate COOKIE-ECHO and the action is
'Association restart', sctp_sf_do_dupcook_a() will processing
the unexpected COOKIE-ECHO for peer restart, but it does not set
the association state to SCTP_STATE_ESTABLISHED, so the association
could stuck in SCTP_STATE_SHUTDOWN_PENDING state forever.
This violates the sctp specification:
RFC 4960 5.2.4. Handle a COOKIE ECHO when a TCB Exists
Action
A) In this case, the peer may have restarted. .....
After this, the endpoint shall enter the ESTABLISHED state.
To resolve this problem, adding a SCTP_CMD_NEW_STATE cmd to the
command list before SCTP_CMD_REPLY cmd, this will set the restart
association to SCTP_STATE_ESTABLISHED state properly and also avoid
I-bit being set in the DATA chunk header when COOKIE_ACK is bundled
with DATA chunks.
Signed-off-by: Xufeng Zhang <xufeng.zhang@windriver.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We did this for IPv4 in b49d3c1e1c "net: ipmr: limit MRT_TABLE
identifiers" but we need to do it for IPv6 as well. On IPv6 the name
is "pim6reg" instead of "pimreg" so there is one less digit allowed.
The strcpy() is in ip6mr_reg_vif().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Control of receive descriptor must not be returned to ethernet chipset
before vlan tag processing is done.
VLAN tag receive word is now reset both in normal and error path.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Spotted-by: Timo Teras <timo.teras@iki.fi>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 9992c2e (net: cdc_ncm: workaround for missing CDC Union)
added code to lookup an IAD for the interface we are probing.
This is redundant. The USB core has already done the lookup
and saved the result in the USB interface struct. Use that
instead.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Cc: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix an skb memleak in DAT
- fix the ARP filtering routine in DAT by preventing bogus entries to overwrite
already existing ones in the local cache.
- fix the ARP filtering routine in DAT by preventing it to parse and add to the
cache bogus entries
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=DvXf
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Included changes ares:
- fix an skb memleak in DAT
- fix the ARP filtering routine in DAT by preventing bogus entries to overwrite
already existing ones in the local cache.
- fix the ARP filtering routine in DAT by preventing it to parse and add to the
cache bogus entries
Signed-off-by: David S. Miller <davem@davemloft.net>
