The initial TLB mapping for the kernel boot didn't set the memory coherent
attribute, MAS2[M], in SMP mode.
If this code supported booting a secondary processor, which it doesn't yet,
but if it did, then when a secondary processor boots, it would probably signal
the primary processor by setting a variable called something like
__secondary_hold_acknowledge. However, due to the lack of the M bit, the
primary processor would not snoop the transaction (even if a transaction were
broadcast). If primary CPU's L1 D-cache had a copy, it would not be flushed
and the CPU would never see the ack. Which would have resulted in the primary
CPU spinning for a long time, perhaps a full second before it gives up, while
it would have waited for the ack from the secondary CPU that it wouldn't have
been able to see because of the stale cache.
The value of MAS2 for the boot page TLB1 entry is a compile time constant,
so there is no need to calculate it in powerpc assembly language.
Also, from the MPC8572 manual section 6.12.5.3, "Bits that represent
offsets within a page are ignored and should be cleared." Existing code
didn't clear them, this code does.
The same when the page of KERNELBASE is found; we don't need to use asm to
mask the lower 12 bits off.
In the code that computes the address to rfi from, don't hard code the
offset to 24 bytes, but have the assembler figure that out for us.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch add the handlers of SPE/EFP exceptions.
The code is used to emulate float point arithmetic,
when MSR(SPE) is enabled and receive EFP data interrupt or EFP round interrupt.
This patch has no conflict with or dependence on FP math-emu.
The code has been tested by TestFloat.
Now the code doesn't support SPE/EFP instructions emulation
(it won't be called when receive program interrupt),
but it could be easily added.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
FP_DECL_EX is already used, so ret is redundant.
And FP_SET_EXCEPTION will add status into return value.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move to using the same macro definition for _FP_CHOOSENAN as s390,
sh, sparc32/64. The original author didn't understand this and
matched what sparc64 was doing and they have updated to this definition.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
PowerPC float point division emulation is derived from gcc.
I reported this problem on gcc maillist and got this reply:
http://gcc.gnu.org/ml/gcc/2008-03/msg00543.html
Since UDIV_NEEDS_NORMALIZATION is not used by kernel, we should use
_FP_DIV_MEAT_1_udiv_norm to make sure the single float point
is normalized before udiv_qrnnd.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
After testing of various compiler flag combinations by Nate Case it was
determined that -mabi=no-spe has no impact on the compiler generating
SPE instructions. Only -mno-spe and -mspe=no do.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The test to check for a new winsize runs out-of-sync with the
underlying tty. After a tty has been released and initialized again,
the winsize might differ between the tty and the hp struct. The
solution is to simply remove the check and always schedule the resize
work.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Otherwise the tests for count < 0 will never be true.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
of_node_put is needed before discarding a value received from
of_find_node_by_name, e.g., in error handling code or when the device
node is no longer used.
The semantic match that catches the bug is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression struct device_node *n;
position p1, p2;
statement S1,S2;
expression E,E1;
expression *ptr != NULL;
@@
(
if (!(n@p1 = of_find_node_by_name(...))) S1
|
n@p1 = of_find_node_by_name(...)
)
<... when != of_node_put(n)
when != if (...) { <+... of_node_put(n) ...+> }
when != true !n || ...
when != n = E
when != E = n
if (!n || ...) S2
...>
(
return \(0\|<+...n...+>\|ptr\);
|
return@p2 ...;
|
n = E1
|
E1 = n
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s of_find_node_by_name %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Nicolas Palix <npalix@diku.dk>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a new function, of_get_gpio_flags, which is like
of_get_gpio(), but accepts a new "flags" argument. This new function
will be used by the drivers that need to retrieve additional GPIO
information, such as active-low flag.
Also, this changes the default ("simple") .xlate routine to warn about
bogus (< 2) #gpio-cells usage: the second cell should always be present
for GPIO flags.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
i2c_smbus_read_word_data() returns a s32, which may be negative
but unsigned len cannot be negative.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For I2C devices we just setting the node pointer in the archdata. This
is needed so that the I2C devices could find their OF tree nodes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The name of the device_node field differ across the platforms, so we
have to implement inlined accessors. This is needed to avoid ugly
#ifdef in the generic code.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds support for multiple BSR nodes in the OF device tree.
Previously, the BSR driver only supported a single OF node describing
a BSR. Apparently when an LPAR is set to use "all system resources"
the BSR appears as a single node, but when it is handed out in pieces,
each 8 byte piece gets its own node. So, this keeps a list of BSR
devices instead of the array and includes all nodes.
Also, this makes the code be more inclusive of what BSR devices we
accept by only checking compatibility and not the device name property
(which might change in the future versions of BSR).
Signed-off-by: Sonny Rao <sonnyrao@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
ibmebus_free_irq() frees the IRQ but does not remove its mapping, which
results in stale entries in the map.
This fixes it by adding a call to irq_dispose_mapping() in
ibmebus_free_irq().
Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As noted by Akinobu Mita in commit b1fceac2 ("x86: remove unnecessary
memset and NULL check after alloc_bootmem()"), alloc_bootmem and
related functions never return NULL and always return a zeroed region
of memory. Thus a NULL test or memset after calls to these functions
is unnecessary.
This was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression E;
statement S;
@@
E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\|alloc_bootmem_node\|alloc_bootmem_low_pages_node\|alloc_bootmem_pages_node\)(...)
... when != E
(
- BUG_ON (E == NULL);
|
- if (E == NULL) S
)
@@
expression E,E1;
@@
E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\|alloc_bootmem_node\|alloc_bootmem_low_pages_node\|alloc_bootmem_pages_node\)(...)
... when != E
- memset(E,0,E1);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We need to swap these out once we start using swiotlb, so add
them to dma_ops. Create CONFIG_PPC_NEED_DMA_SYNC_OPS Kconfig
option; this is currently enabled automatically if we're
CONFIG_NOT_COHERENT_CACHE. In the future, this will also
be enabled for builds that need swiotlb. If PPC_NEED_DMA_SYNC_OPS
is not defined, the dma_sync_*_for_* ops compile to nothing.
Otherwise, they access the dma_ops pointers for the sync ops.
This patch also changes dma_sync_single_range_* to actually
sync the range - previously it was using a generous
dma_sync_single. dma_sync_single_* is now implemented
as a dma_sync_single_range with an offset of 0.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On my screen, when something crashes, I only have space for maybe 16
functions of the stack trace before the information above it scrolls
off the screen. It's easy to hack the kernel to print out only that
much, but it's harder to remember to do it. This introduces a config
option for it so that I can keep the setting in my config.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Refactor the RCU based pte free code that was used on ppc64 to be used
on all powerpc.
Additionally refactor pte_free() & pte_free_kernel() into common code
between ppc32 & ppc64.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The tlb invalidates in kmap_atomic/kunmap_atomic can be called from
IRQ context, however they are only local invalidates (on the processor
that the kmap was called on). In the future we want to use IPIs to
do tlb invalidates this causes issue since flush_tlb_page() is considered
a broadcast invalidate.
Add local_flush_tlb_page() as a non-broadcast invalidate and use it in
kmap_atomic() since we don't have enough information in the
flush_tlb_page() call to determine its local.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Clean up the ifdefs so we only use hash_page_sync if we have
CONFIG_SMP && CONFIG_PPC_STD_MMU_32.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 32-bit hash code didn't need it so far so we don't update
mm->cpu_vm_mask on context switch. This however will break when we
merge the RCU based page table freeing patch and other upcoming 32-bit
embedded SMP work, so this adds the update.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On PowerPC 4xx or other non cache-coherent platforms, we lost the
appropriate cache flushing in dma_map_sg() when merging the 32 and
64-bit DMA code (commit 4fc665b88a,
"powerpc: Merge 32 and 64-bit dma code"). This restores it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] hpwdt: Fix kdump when using hpwdt
[WATCHDOG] hpwdt: set the mapped BIOS address space as executable
[WATCHDOG] iTCO_wdt: add PCI ID's for ICH9 & ICH10 chipsets
[WATCHDOG] iTCO_wdt : correct status clearing
[WATCHDOG] iTCO_wdt : problem with rebooting on new ICH9 based motherboards
[WATCHDOG] fix mtx1_wdt compilation failure
* 'linux-next' of git://git.infradead.org/ubifs-2.6:
UBIFS: pre-allocate bulk-read buffer
UBIFS: do not allocate too much
UBIFS: do not print scary memory allocation warnings
UBIFS: allow for gaps when dirtying the LPT
UBIFS: fix compilation warnings
MAINTAINERS: change UBI/UBIFS git tree URLs
UBIFS: endian handling fixes and annotations
UBIFS: remove printk
* 'kvm-updates/2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: MMU: avoid creation of unreachable pages in the shadow
KVM: ppc: stop leaking host memory on VM exit
KVM: MMU: fix sync of ptes addressed at owner pagetable
KVM: ia64: Fix: Use correct calling convention for PAL_VPS_RESUME_HANDLER
KVM: ia64: Fix incorrect kbuild CFLAGS override
KVM: VMX: Fix interrupt loss during race with NMI
KVM: s390: Fix problem state handling in guest sigp handler
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Update defconfigs for 2.6.28-rc7
macfb: Do not overflow fb_fix_screeninfo.id
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] stex: switch to block timeout
[SCSI] make scsi_eh_try_stu use block timeout
[SCSI] megaraid_sas: switch to block timeout
[SCSI] ibmvscsi: switch to block timeout
[SCSI] aacraid: switch to block timeout
[SCSI] zfcp: prevent double decrement on host_busy while being busy
[SCSI] zfcp: fix deadlock between wq triggered port scan and ERP
[SCSI] zfcp: eliminate race between validation and locking
[SCSI] zfcp: verify for correct rport state before scanning for SCSI devs
[SCSI] zfcp: returning an ERR_PTR where a NULL value is expected
[SCSI] zfcp: Fix opening of wka ports
[SCSI] zfcp: fix remote port status check
[SCSI] fc_transport: fix old bug on bitflag definitions
[SCSI] Fix hang in starved list processing
This fixes the MN10300 kernel module linking to match the toolchain. RELA
relocs don't use the value at the location being relocated. This has been
working because the tools always leave the value at the target location
cleared.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If xpc.ko and gru.ko are both statically linked into the kernel, then
xpc_init() can get called before gru_init() and make a call to one of the
gru's exported functions before the gru has initialized itself. The end
result is a NULL dereference.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the CONFIG_SMP case the irq_choose_cpu() code was returning back
a logical cpu id not the physical id. We were writing that directly
into the HW register.
We need to be calling get_hard_smp_processor_id() so irq_choose_cpu()
always returns a physical cpu id.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Count the insertion of new pages in the statistics used to drive the
pageout scanning code. This should help the kernel quickly evict
streaming file IO.
We count on the fact that new file pages start on the inactive file LRU
and new anonymous pages start on the active anon list. This means
streaming file IO will increment the recent scanned file statistic, while
leaving the recent rotated file statistic alone, driving pageout scanning
to the file LRUs.
Pageout activity does its own list manipulation.
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Tested-by: Gene Heskett <gene.heskett@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Devices which share the same queue, like floppies and mtd devices, get
registered multiple times in the bdi interface, but bdi accounts only the
last registered device of the devices sharing one queue.
On remove, all earlier registered devices leak, stay around in sysfs, and
cause "duplicate filename" errors if the devices are re-created.
This prevents the creation of multiple bdi interfaces per queue, and the
bdi device will carry the dev_t name of the block device which is the
first one registered, of the pool of devices using the same queue.
[akpm@linux-foundation.org: add a WARN_ON so we know which drivers are misbehaving]
Tested-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The previous patch from Alan Cox ("nfsd: fix vm overcommit crash",
commit 731572d39f) fixed the problem where
knfsd crashes on exported shmemfs objects and strict overcommit is set.
But the patch forgot supporting the case when CONFIG_SECURITY is
disabled.
This patch copies a part of his fix which is mainly for detecting a bug
earlier.
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Junjiro R. Okajima <hooanon05@yahoo.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We guarantee 400ns delay at the time of issuing the command.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Also while at it:
* Drop unused arguments from ide_complete_power_step().
* Move DEBUG_PM printk() from ide_end_drive_cmd() to
ide_complete_power_step().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Respect current DMA setting during resume, otherwise PIO timings
may get destroyed if host uses shared PIO/MWDMA timings.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It seems that on some nVidia controllers using AltStatus register
can be unreliable so default to Status register if the PCI device
is in Compatibility Mode. In order to achieve this:
* Add ide_pci_is_in_compatibility_mode() inline helper to <linux/ide.h>.
* Add IDE_HFLAG_BROKEN_ALTSTATUS host flag and set it in amd74xx host
driver for nVidia controllers in Compatibility Mode.
* Teach actual_try_to_identify() and drive_is_ready() about the new flag.
This fixes the regression caused by removal of CONFIG_IDEPCI_SHARE_IRQ
config option in 2.6.25 and using AltStatus register unconditionally when
available (kernel.org bugs #11659 and #10216).
[ Moreover for CONFIG_IDEPCI_SHARE_IRQ=y (which is what most people
and distributions use) it never worked correctly. ]
Thanks to Remy LABENE and Lars Winterfeld for help with debugging the problem.
More info at:
http://bugzilla.kernel.org/show_bug.cgi?id=11659http://bugzilla.kernel.org/show_bug.cgi?id=10216
Reported-by: Remy LABENE <remy.labene@free.fr>
Tested-by: Remy LABENE <remy.labene@free.fr>
Tested-by: Lars Winterfeld <lars.winterfeld@tu-ilmenau.de>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Don't overflow the 16-character fb_fix_screeninfo id string (fixes some
console erasing and blanking artifacts). Have the ID default to "Unknown"
on machines with no built-in video and no nubus devices. Check for
fb_alloc_cmap failure.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Kumar Gala