[ Upstream commit d43e2675e9 ]
KVM stores the gfn in MMIO SPTEs as a caching optimization. These are split
in two parts, as in "[high 11111 low]", to thwart any attempt to use these bits
in an L1TF attack. This works as long as there are 5 free bits between
MAXPHYADDR and bit 50 (inclusive), leaving bit 51 free so that the MMIO
access triggers a reserved-bit-set page fault.
The bit positions however were computed wrongly for AMD processors that have
encryption support. In this case, x86_phys_bits is reduced (for example
from 48 to 43, to account for the C bit at position 47 and four bits used
internally to store the SEV ASID and other stuff) while x86_cache_bits in
would remain set to 48, and _all_ bits between the reduced MAXPHYADDR
and bit 51 are set. Then low_phys_bits would also cover some of the
bits that are set in the shadow_mmio_value, terribly confusing the gfn
caching mechanism.
To fix this, avoid splitting gfns as long as the processor does not have
the L1TF bug (which includes all AMD processors). When there is no
splitting, low_phys_bits can be set to the reduced MAXPHYADDR removing
the overlap. This fixes "npt=0" operation on EPYC processors.
Thanks to Maxim Levitsky for bisecting this bug.
Cc: stable@vger.kernel.org
Fixes: 52918ed5fc ("KVM: SVM: Override default MMIO mask if memory encryption is enabled")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2abfc0448 ]
Commit
21b5ee59ef ("x86/cpu/amd: Enable the fixed Instructions Retired
counter IRPERF")
mistakenly added erratum #1054 as an OS Visible Workaround (OSVW) ID 0.
Erratum #1054 is not OSVW ID 0 [1], so make it a legacy erratum.
There would never have been a false positive on older hardware that
has OSVW bit 0 set, since the IRPERF feature was not available.
However, save a couple of RDMSR executions per thread, on modern
system configurations that correctly set non-zero values in their
OSVW_ID_Length MSRs.
[1] Revision Guide for AMD Family 17h Models 00h-0Fh Processors. The
revision guide is available from the bugzilla link below.
Fixes: 21b5ee59ef ("x86/cpu/amd: Enable the fixed Instructions Retired counter IRPERF")
Reported-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200417143356.26054-1-kim.phillips@amd.com
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206537
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1750a3d9a ]
After disabling a function, the original handle is logged instead of
the disabled handle.
Link: https://lkml.kernel.org/r/20200522183922.5253-1-ptesarik@suse.com
Fixes: 17cdec960c ("s390/pci: Recover handle in clp_set_pci_fn()")
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Petr Tesarik <ptesarik@suse.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a101950fcb ]
Commit 1ca3dec2b2 ("powerpc/xive: Prevent page fault issues in the
machine crash handler") fixed an issue in the FW assisted dump of
machines using hash MMU and the XIVE interrupt mode under the POWER
hypervisor. It forced the mapping of the ESB page of interrupts being
mapped in the Linux IRQ number space to make sure the 'crash kexec'
sequence worked during such an event. But it didn't handle the
un-mapping.
This mapping is now blocking the removal of a passthrough IO adapter
under the POWER hypervisor because it expects the guest OS to have
cleared all page table entries related to the adapter. If some are
still present, the RTAS call which isolates the PCI slot returns error
9001 "valid outstanding translations".
Remove these mapping in the IRQ data cleanup routine.
Under KVM, this cleanup is not required because the ESB pages for the
adapter interrupts are un-mapped from the guest by the hypervisor in
the KVM XIVE native device. This is now redundant but it's harmless.
Fixes: 1ca3dec2b2 ("powerpc/xive: Prevent page fault issues in the machine crash handler")
Cc: stable@vger.kernel.org # v5.5+
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200429075122.1216388-2-clg@kaod.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0bbb53843 ]
Current implementation could destory a4 & a5 when strace, so we need to get them
from pt_regs by SAVE_ALL.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3866f217aa ]
call_undef_hook() in traps.c applies the same instr_mask for both 16-bit
and 32-bit thumb instructions. If instr_mask then is only 16 bits wide
(0xffff as opposed to 0xffffffff), the first half-word of 32-bit thumb
instructions will be masked out. This makes the function match 32-bit
thumb instructions where the second half-word is equal to instr_val,
regardless of the first half-word.
The result in this case is that all undefined 32-bit thumb instructions
with the second half-word equal to 0xde01 (udf #1) work as breakpoints
and will raise a SIGTRAP instead of a SIGILL, instead of just the one
intended 16-bit instruction. An example of such an instruction is
0xeaa0de01, which is unallocated according to Arm ARM and should raise a
SIGILL, but instead raises a SIGTRAP.
This patch fixes the issue by setting all the bits in instr_mask, which
will still match the intended 16-bit thumb instruction (where the
upper half is always 0), but not any 32-bit thumb instructions.
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Fredrik Strupe <fredrik@strupe.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 90ceddcb49 upstream.
Simplify gen_btf logic to make it work with llvm-objcopy. The existing
'file format' and 'architecture' parsing logic is brittle and does not
work with llvm-objcopy/llvm-objdump.
'file format' output of llvm-objdump>=11 will match GNU objdump, but
'architecture' (bfdarch) may not.
.BTF in .tmp_vmlinux.btf is non-SHF_ALLOC. Add the SHF_ALLOC flag
because it is part of vmlinux image used for introspection. C code
can reference the section via linker script defined __start_BTF and
__stop_BTF. This fixes a small problem that previous .BTF had the
SHF_WRITE flag (objcopy -I binary -O elf* synthesized .data).
Additionally, `objcopy -I binary` synthesized symbols
_binary__btf_vmlinux_bin_start and _binary__btf_vmlinux_bin_stop (not
used elsewhere) are replaced with more commonplace __start_BTF and
__stop_BTF.
Add 2>/dev/null because GNU objcopy (but not llvm-objcopy) warns
"empty loadable segment detected at vaddr=0xffffffff81000000, is this intentional?"
We use a dd command to change the e_type field in the ELF header from
ET_EXEC to ET_REL so that lld will accept .btf.vmlinux.bin.o. Accepting
ET_EXEC as an input file is an extremely rare GNU ld feature that lld
does not intend to support, because this is error-prone.
The output section description .BTF in include/asm-generic/vmlinux.lds.h
avoids potential subtle orphan section placement issues and suppresses
--orphan-handling=warn warnings.
Fixes: df786c9b94 ("bpf: Force .BTF section start to zero when dumping from vmlinux")
Fixes: cb0cc635c7 ("powerpc: Include .BTF section")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Fangrui Song <maskray@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Stanislav Fomichev <sdf@google.com>
Tested-by: Andrii Nakryiko <andriin@fb.com>
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Link: https://github.com/ClangBuiltLinux/linux/issues/871
Link: https://lore.kernel.org/bpf/20200318222746.173648-1-maskray@google.com
Signed-off-by: Maria Teguiani <teguiani@google.com>
Tested-by: Matthias Maennich <maennich@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e5b3c267d upstream
SRBDS is an MDS-like speculative side channel that can leak bits from the
random number generator (RNG) across cores and threads. New microcode
serializes the processor access during the execution of RDRAND and
RDSEED. This ensures that the shared buffer is overwritten before it is
released for reuse.
While it is present on all affected CPU models, the microcode mitigation
is not needed on models that enumerate ARCH_CAPABILITIES[MDS_NO] in the
cases where TSX is not supported or has been disabled with TSX_CTRL.
The mitigation is activated by default on affected processors and it
increases latency for RDRAND and RDSEED instructions. Among other
effects this will reduce throughput from /dev/urandom.
* Enable administrator to configure the mitigation off when desired using
either mitigations=off or srbds=off.
* Export vulnerability status via sysfs
* Rename file-scoped macros to apply for non-whitelist table initializations.
[ bp: Massage,
- s/VULNBL_INTEL_STEPPING/VULNBL_INTEL_STEPPINGS/g,
- do not read arch cap MSR a second time in tsx_fused_off() - just pass it in,
- flip check in cpu_set_bug_bits() to save an indentation level,
- reflow comments.
jpoimboe: s/Mitigated/Mitigation/ in user-visible strings
tglx: Dropped the fused off magic for now
]
Signed-off-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Tested-by: Neelima Krishnan <neelima.krishnan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93920f61c2 upstream
To make cpu_matches() reusable for other matching tables, have it take a
pointer to a x86_cpu_id table as an argument.
[ bp: Flip arguments order. ]
Signed-off-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9d7144597 upstream
Intel uses the same family/model for several CPUs. Sometimes the
stepping must be checked to tell them apart.
On x86 there can be at most 16 steppings. Add a steppings bitmask to
x86_cpu_id and a X86_MATCH_VENDOR_FAMILY_MODEL_STEPPING_FEATURE macro
and support for matching against family/model/stepping.
[ bp: Massage.
tglx: Lightweight variant for backporting ]
Signed-off-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e41a766c9 upstream.
New Zhaoxin family 7 CPUs are not affected by SPECTRE_V2. So define a
separate cpu_vuln_whitelist bit NO_SPECTRE_V2 and add these CPUs to the cpu
vulnerability whitelist.
Signed-off-by: Tony W Wang-oc <TonyWWang-oc@zhaoxin.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/1579227872-26972-2-git-send-email-TonyWWang-oc@zhaoxin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ac8372f3b4 ]
On s390, the layout of normal and large ptes (i.e. pmds/puds) differs.
Therefore, set_huge_pte_at() does a conversion from a normal pte to
the corresponding large pmd/pud. So, when converting an empty pte, this
should result in an empty pmd/pud, which would return true for
pmd/pud_none().
However, after conversion we also mark the pmd/pud as large, and
therefore present. For empty ptes, this will result in an empty pmd/pud
that is also marked as large, and pmd/pud_none() would not return true.
There is currently no issue with this behaviour, as set_huge_pte_at()
does not seem to be called for empty ptes. It would be valid though, so
let's fix this by not marking empty ptes as large in set_huge_pte_at().
This was found by testing a patch from from Anshuman Khandual, which is
currently discussed on LKML ("mm/debug: Add more arch page table helper
tests").
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7110a26e5 ]
When building with Clang + -Wtautological-compare and
CONFIG_CPUMASK_OFFSTACK unset:
arch/x86/mm/mmio-mod.c:375:6: warning: comparison of array 'downed_cpus'
equal to a null pointer is always false [-Wtautological-pointer-compare]
if (downed_cpus == NULL &&
^~~~~~~~~~~ ~~~~
arch/x86/mm/mmio-mod.c:405:6: warning: comparison of array 'downed_cpus'
equal to a null pointer is always false [-Wtautological-pointer-compare]
if (downed_cpus == NULL || cpumask_weight(downed_cpus) == 0)
^~~~~~~~~~~ ~~~~
2 warnings generated.
Commit
f7e30f01a9 ("cpumask: Add helper cpumask_available()")
added cpumask_available() to fix warnings of this nature. Use that here
so that clang does not warn regardless of CONFIG_CPUMASK_OFFSTACK's
value.
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Link: https://github.com/ClangBuiltLinux/linux/issues/982
Link: https://lkml.kernel.org/r/20200408205323.44490-1-natechancellor@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 799587d573 ]
Elide invalid configuration EZNPS + ARCv2, triggered by a
make allyesconfig build.
Granted the root cause is in source code (asm/barrier.h) where we check
for ARCv2 before PLAT_EZNPS, but it is better to avoid such combinations
at onset rather then baking subtle nuances into code.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43900edf67 ]
As of today the ICCM and DCCM size checks are incorrectly using
mismatched units (KiB checked against bytes). The CONFIG_ARC_DCCM_SZ
and CONFIG_ARC_ICCM_SZ are in KiB, but the size calculated in
runtime and stored in cpu->dccm.sz and cpu->iccm.sz is in bytes.
Fix that.
Reported-by: Paul Greco <pmgreco@us.ibm.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b4adfe5591 ]
A typical backtrace acquired from ftraced function currently looks like
the following (e.g. for "path_openat"):
arch_stack_walk+0x15c/0x2d8
stack_trace_save+0x50/0x68
stack_trace_call+0x15a/0x3b8
ftrace_graph_caller+0x0/0x1c
0x3e0007e3c98 <- ftraced function caller (should be do_filp_open+0x7c/0xe8)
do_open_execat+0x70/0x1b8
__do_execve_file.isra.0+0x7d8/0x860
__s390x_sys_execve+0x56/0x68
system_call+0xdc/0x2d8
Note random "0x3e0007e3c98" stack value as ftraced function caller. This
value causes either imprecise unwinder result or unwinding failure.
That "0x3e0007e3c98" comes from r14 of ftraced function stack frame, which
it haven't had a chance to initialize since the very first instruction
calls ftrace code ("ftrace_caller"). (ftraced function might never
save r14 as well). Nevertheless according to s390 ABI any function
is called with stack frame allocated for it and r14 contains return
address. "ftrace_caller" itself is called with "brasl %r0,ftrace_caller".
So, to fix this issue simply always save traced function caller onto
ftraced function stack frame.
Reported-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69393cb03c ]
Xmon should be either fully or partially disabled depending on the
kernel lockdown state.
Put xmon into read-only mode for lockdown=integrity and prevent user
entry into xmon when lockdown=confidentiality. Xmon checks the lockdown
state on every attempted entry:
(1) during early xmon'ing
(2) when triggered via sysrq
(3) when toggled via debugfs
(4) when triggered via a previously enabled breakpoint
The following lockdown state transitions are handled:
(1) lockdown=none -> lockdown=integrity
set xmon read-only mode
(2) lockdown=none -> lockdown=confidentiality
clear all breakpoints, set xmon read-only mode,
prevent user re-entry into xmon
(3) lockdown=integrity -> lockdown=confidentiality
clear all breakpoints, set xmon read-only mode,
prevent user re-entry into xmon
Suggested-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Christopher M. Riedl <cmr@informatik.wtf>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190907061124.1947-3-cmr@informatik.wtf
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48e626ac85 ]
export_imc_mode_and_cmd() function which creates the debugfs interface
for imc-mode and imc-command, is invoked when each nest pmu units is
registered.
When the first nest pmu unit is registered, export_imc_mode_and_cmd()
creates 'imc' directory under `/debug/powerpc/`. In the subsequent
invocations debugfs_create_dir() function returns, since the directory
already exists.
The recent commit <c33d442328f55> (debugfs: make error message a bit
more verbose), throws a warning if we try to invoke
`debugfs_create_dir()` with an already existing directory name.
Address this warning by making the debugfs directory registration in
the opal_imc_counters_probe() function, i.e invoke
export_imc_mode_and_cmd() function from the probe function.
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Tested-by: Nageswara R Sastry <nasastry@in.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191127072035.4283-1-anju@linux.vnet.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5bfea2d9b1 upstream.
The original code in mm/mremap.c checks huge pmd by:
if (is_swap_pmd(*old_pmd) || pmd_trans_huge(*old_pmd)) {
However, a DAX mapped nvdimm is mapped as huge page (by default) but it
is not transparent huge page (_PAGE_PSE | PAGE_DEVMAP). This commit
changes the condition to include the case.
This addresses CVE-2020-10757.
Fixes: 5c7fb56e5e ("mm, dax: dax-pmd vs thp-pmd vs hugetlbfs-pmd")
Cc: <stable@vger.kernel.org>
Reported-by: Fan Yang <Fan_Yang@sjtu.edu.cn>
Signed-off-by: Fan Yang <Fan_Yang@sjtu.edu.cn>
Tested-by: Fan Yang <Fan_Yang@sjtu.edu.cn>
Tested-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8874347066 upstream.
The intermediate result of the old term (4UL * 1024 * 1024 * 1024) is
4 294 967 296 or 0x100000000 which is no problem on 64 bit systems.
The patch does not change the later overall result of 0x100000 for
MAX_DMA32_PFN (after it has been shifted by PAGE_SHIFT). The new
calculation yields the same result, but does not require 64 bit
arithmetic.
On 32 bit systems the old calculation suffers from an arithmetic
overflow in that intermediate term in braces: 4UL aka unsigned long int
is 4 byte wide and an arithmetic overflow happens (the 0x100000000 does
not fit in 4 bytes), the in braces result is truncated to zero, the
following right shift does not alter that, so MAX_DMA32_PFN evaluates to
0 on 32 bit systems.
That wrong value is a problem in a comparision against MAX_DMA32_PFN in
the init code for swiotlb in pci_swiotlb_detect_4gb() to decide if
swiotlb should be active. That comparison yields the opposite result,
when compiling on 32 bit systems.
This was not possible before
1b7e03ef75 ("x86, NUMA: Enable emulation on 32bit too")
when that MAX_DMA32_PFN was first made visible to x86_32 (and which
landed in v3.0).
In practice this wasn't a problem, unless CONFIG_SWIOTLB is active on
x86-32.
However if one has set CONFIG_IOMMU_INTEL, since
c5a5dc4cbb ("iommu/vt-d: Don't switch off swiotlb if bounce page is used")
there's a dependency on CONFIG_SWIOTLB, which was not necessarily
active before. That landed in v5.4, where we noticed it in the fli4l
Linux distribution. We have CONFIG_IOMMU_INTEL active on both 32 and 64
bit kernel configs there (I could not find out why, so let's just say
historical reasons).
The effect is at boot time 64 MiB (default size) were allocated for
bounce buffers now, which is a noticeable amount of memory on small
systems like pcengines ALIX 2D3 with 256 MiB memory, which are still
frequently used as home routers.
We noticed this effect when migrating from kernel v4.19 (LTS) to v5.4
(LTS) in fli4l and got that kernel messages for example:
Linux version 5.4.22 (buildroot@buildroot) (gcc version 7.3.0 (Buildroot 2018.02.8)) #1 SMP Mon Nov 26 23:40:00 CET 2018
…
Memory: 183484K/261756K available (4594K kernel code, 393K rwdata, 1660K rodata, 536K init, 456K bss , 78272K reserved, 0K cma-reserved, 0K highmem)
…
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
software IO TLB: mapped [mem 0x0bb78000-0x0fb78000] (64MB)
The initial analysis and the suggested fix was done by user 'sourcejedi'
at stackoverflow and explicitly marked as GPLv2 for inclusion in the
Linux kernel:
https://unix.stackexchange.com/a/520525/50007
The new calculation, which does not suffer from that overflow, is the
same as for arch/mips now as suggested by Robin Murphy.
The fix was tested by fli4l users on round about two dozen different
systems, including both 32 and 64 bit archs, bare metal and virtualized
machines.
[ bp: Massage commit message. ]
Fixes: 1b7e03ef75 ("x86, NUMA: Enable emulation on 32bit too")
Reported-by: Alan Jenkins <alan.christopher.jenkins@gmail.com>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Alexander Dahl <post@lespocky.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Link: https://unix.stackexchange.com/q/520065/50007
Link: https://web.nettworks.org/bugs/browse/FFL-2560
Link: https://lkml.kernel.org/r/20200526175749.20742-1-post@lespocky.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 700d3a5a66 upstream.
Revert
45e29d119e ("x86/syscalls: Make __X32_SYSCALL_BIT be unsigned long")
and add a comment to discourage someone else from making the same
mistake again.
It turns out that some user code fails to compile if __X32_SYSCALL_BIT
is unsigned long. See, for example [1] below.
[ bp: Massage and do the same thing in the respective tools/ header. ]
Fixes: 45e29d119e ("x86/syscalls: Make __X32_SYSCALL_BIT be unsigned long")
Reported-by: Thorsten Glaser <t.glaser@tarent.de>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: stable@kernel.org
Link: [1] https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=954294
Link: https://lkml.kernel.org/r/92e55442b744a5951fdc9cfee10badd0a5f7f828.1588983892.git.luto@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bf71bc16e0 ]
The Debian kernel v5.6 triggers this kernel panic:
Kernel panic - not syncing: Bad Address (null pointer deref?)
Bad Address (null pointer deref?): Code=26 (Data memory access rights trap) at addr 0000000000000000
CPU: 0 PID: 0 Comm: swapper Not tainted 5.6.0-2-parisc64 #1 Debian 5.6.14-1
IAOQ[0]: mem_init+0xb0/0x150
IAOQ[1]: mem_init+0xb4/0x150
RP(r2): start_kernel+0x6c8/0x1190
Backtrace:
[<0000000040101ab4>] start_kernel+0x6c8/0x1190
[<0000000040108574>] start_parisc+0x158/0x1b8
on a HP-PARISC rp3440 machine with this memory layout:
Memory Ranges:
0) Start 0x0000000000000000 End 0x000000003fffffff Size 1024 MB
1) Start 0x0000004040000000 End 0x00000040ffdfffff Size 3070 MB
Fix the crash by avoiding virt_to_page() and similar functions in
mem_init() until the memory zones have been fully set up.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.0+
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be0ec060b5 ]
These error messages are output when booting on a BCM HR2 system:
GIC: PPI11 is secure or misconfigured
GIC: PPI13 is secure or misconfigured
Per ARM documentation these interrupts are triggered on a rising edge.
See ARM Cortex A-9 MPCore Technical Reference Manual, Revision r4p1,
Section 3.3.8 Interrupt Configuration Registers.
The same issue was resolved for NSP systems in commit 5f1aa51c7a
("ARM: dts: NSP: Fix PPI interrupt types").
Fixes: b9099ec754 ("ARM: dts: Add Broadcom Hurricane 2 DTS include file")
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58bb90ab41 ]
The status "ACT" led on the Raspberry Pi Zero W is on when GPIO 47 is low.
This has been verified on a board and somewhat confirmed by both the GPIO
name ("STATUS_LED_N") and the reduced schematics [1].
[1]: https://www.raspberrypi.org/documentation/hardware/raspberrypi/schematics/rpi_SCH_ZeroW_1p1_reduced.pdf
Fixes: 2c7c040c73 ("ARM: dts: bcm2835: Add Raspberry Pi Zero W")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 665e7c73a7 ]
Avoid LDB and IPU DI clocks both using the same parent. LDB requires
pasthrough clock to avoid breaking timing while IPU DI does not.
Force IPU DI clocks to use IMX6QDL_CLK_PLL2_PFD0_352M as parent
and LDB to use IMX6QDL_CLK_PLL5_VIDEO_DIV.
This fixes an issue where attempting atomic modeset while using
HDMI and display port at the same time causes LDB clock programming
to destroy the programming of HDMI that was done during the same
modeset.
Cc: stable@vger.kernel.org
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
[Use IMX6QDL_CLK_PLL2_PFD0_352M instead of IMX6QDL_CLK_PLL2_PFD2_396M
originally chosen by Robert Beckett to avoid affecting eMMC clock
by DRM atomic updates]
Signed-off-by: Ian Ray <ian.ray@ge.com>
[Squash Robert's and Ian's commits for bisectability, update patch
description and add stable tag]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b1f6c5e4d ]
Fix the assigned-clock-parents to higher frequency clock to avoid h264
encode timeout:
[ 134.763465] mtk_vpu 10020000.vpu: vpu ipi 4 ack time out !
[ 134.769008] [MTK_VCODEC][ERROR][18]: vpu_enc_send_msg() vpu_ipi_send msg_id c002 len 32 fail -5
[ 134.777707] [MTK_VCODEC][ERROR][18]: vpu_enc_encode() AP_IPIMSG_ENC_ENCODE 0 fail
venc_sel is the clock used by h264 encoder, and venclt_sel is the clock
used by vp8 encoder. Assign venc_sel to vcodecpll_ck and venclt_sel to
vcodecpll_370p5.
vcodecpll 1482000000
vcodecpll_ck 494000000
venc_sel 494000000
...
vcodecpll_370p5 370500000
venclt_sel 370500000
Fixes: fbbad0287c ("arm64: dts: Using standard CCF interface to set vcodec clk")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20200504124442.208004-1-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 71f8af1110 ]
Tomas Paukrt reports that his SAM9X60 based system (ARM926, ARMv5TJ)
fails to fix up alignment faults, eventually resulting in a kernel
oops.
The problem occurs when using CONFIG_CPU_USE_DOMAINS with commit
e6978e4bf1 ("ARM: save and reset the address limit when entering an
exception"). This is because the address limit is set back to
TASK_SIZE on exception entry, and, although it is restored on exception
exit, the domain register is not.
Hence, this sequence can occur:
interrupt
pt_regs->addr_limit = addr_limit // USER_DS
addr_limit = USER_DS
alignment exception
__probe_kernel_read()
old_fs = get_fs() // USER_DS
set_fs(KERNEL_DS)
addr_limit = KERNEL_DS
dacr.kernel = DOMAIN_MANAGER
interrupt
pt_regs->addr_limit = addr_limit // KERNEL_DS
addr_limit = USER_DS
alignment exception
__probe_kernel_read()
old_fs = get_fs() // USER_DS
set_fs(KERNEL_DS)
addr_limit = KERNEL_DS
dacr.kernel = DOMAIN_MANAGER
...
set_fs(old_fs)
addr_limit = USER_DS
dacr.kernel = DOMAIN_CLIENT
...
addr_limit = pt_regs->addr_limit // KERNEL_DS
interrupt returns
At this point, addr_limit is correctly restored to KERNEL_DS for
__probe_kernel_read() to continue execution, but dacr.kernel is not,
it has been reset by the set_fs(old_fs) to DOMAIN_CLIENT.
This would not have happened prior to the mentioned commit, because
addr_limit would remain KERNEL_DS, so get_fs() would have returned
KERNEL_DS, and so would correctly nest.
This commit fixes the problem by also saving the DACR on exception
entry if either CONFIG_CPU_SW_DOMAIN_PAN or CONFIG_CPU_USE_DOMAINS are
enabled, and resetting the DACR appropriately on exception entry to
match addr_limit and PAN settings.
Fixes: e6978e4bf1 ("ARM: save and reset the address limit when entering an exception")
Reported-by: Tomas Paukrt <tomas.paukrt@advantech.cz>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 747ffc2fcf ]
Consolidate the user access assembly code to asm/uaccess-asm.h. This
moves the csdb, check_uaccess, uaccess_mask_range_ptr, uaccess_enable,
uaccess_disable, uaccess_save, uaccess_restore macros, and creates two
new ones for exception entry and exit - uaccess_entry and uaccess_exit.
This makes the uaccess_save and uaccess_restore macros private to
asm/uaccess-asm.h.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c962369d7 ]
The size field of the tag header structure is supposed to be set to the
size of a tag structure including the header.
Fixes: c772568788 ("ARM: add additional table to compressed kernel")
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51bb38cb78 ]
If raw_copy_from_user(to, from, N) returns K, callers expect
the first N - K bytes starting at to to have been replaced with
the contents of corresponding area starting at from and the last
K bytes of destination *left* *unmodified*.
What arch/sky/lib/usercopy.c is doing is broken - it can lead to e.g.
data corruption on write(2).
raw_copy_to_user() is inaccurate about return value, which is a bug,
but consequences are less drastic than for raw_copy_from_user().
And just what are those access_ok() doing in there? I mean, look into
linux/uaccess.h; that's where we do that check (as well as zero tail
on failure in the callers that need zeroing).
AFAICS, all of that shouldn't be hard to fix; something like a patch
below might make a useful starting point.
I would suggest moving these macros into usercopy.c (they are never
used anywhere else) and possibly expanding them there; if you leave
them alive, please at least rename __copy_user_zeroing(). Again,
it must not zero anything on failed read.
Said that, I'm not sure we won't be better off simply turning
usercopy.c into usercopy.S - all that is left there is a couple of
functions, each consisting only of inline asm.
Guo Ren reply:
Yes, raw_copy_from_user is wrong, it's no need zeroing code.
unsigned long _copy_from_user(void *to, const void __user *from,
unsigned long n)
{
unsigned long res = n;
might_fault();
if (likely(access_ok(from, n))) {
kasan_check_write(to, n);
res = raw_copy_from_user(to, from, n);
}
if (unlikely(res))
memset(to + (n - res), 0, res);
return res;
}
EXPORT_SYMBOL(_copy_from_user);
You are right and access_ok() should be removed.
but, how about:
do {
...
"2: stw %3, (%1, 0) \n" \
+ " subi %0, 4 \n" \
"9: stw %4, (%1, 4) \n" \
+ " subi %0, 4 \n" \
"10: stw %5, (%1, 8) \n" \
+ " subi %0, 4 \n" \
"11: stw %6, (%1, 12) \n" \
+ " subi %0, 4 \n" \
" addi %2, 16 \n" \
" addi %1, 16 \n" \
Don't expand __ex_table
AI Viro reply:
Hey, I've no idea about the instruction scheduling on csky -
if that doesn't slow the things down, all the better. It's just
that copy_to_user() and friends are on fairly hot codepaths,
and in quite a few situations they will dominate the speed of
e.g. read(2). So I tried to keep the fast path unchanged.
Up to the architecture maintainers, obviously. Which would be
you...
As for the fixups size increase (__ex_table size is unchanged)...
You have each of those macros expanded exactly once.
So the size is not a serious argument, IMO - useless complexity
would be, if it is, in fact, useless; the size... not really,
especially since those extra subi will at least offset it.
Again, up to you - asm optimizations of (essentially)
memcpy()-style loops are tricky and can depend upon the
fairly subtle details of architecture. So even on something
I know reasonably well I would resort to direct experiments
if I can't pass the buck to architecture maintainers.
It *is* worth optimizing - this is where read() from a file
that is already in page cache spends most of the time, etc.
Guo Ren reply:
Thx, after fixup some typo “sub %0, 4”, apply the patch.
TODO:
- user copy/from codes are still need optimizing.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6633a5aa8e ]
Interrupt has been disabled in __schedule() with local_irq_disable()
and enabled in finish_task_switch->finish_lock_switch() with
local_irq_enabled(), So needn't to disable irq here.
Signed-off-by: Liu Yibin <jiulong@linux.alibaba.com>
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 165f2d2858 ]
Just as comment mentioned, the msa format:
cr<30/31, 15> MSA register format:
31 - 29 | 28 - 9 | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0
BA Reserved SH WA B SO SEC C D V
So we should shift 29 bits not 28 bits for mask
Signed-off-by: Liu Yibin <jiulong@linux.alibaba.com>
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0502bee37c ]
Drop static declaration to fix following build error if FRAME_POINTER disabled,
riscv64-linux-ld: arch/riscv/kernel/perf_callchain.o: in function `.L0':
perf_callchain.c:(.text+0x2b8): undefined reference to `walk_stackframe'
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 855bdca178 ]
A test with the command below gives these errors:
arch/arm/boot/dts/rk3229-evb.dt.yaml: spi-0:
'#address-cells' is a required property
arch/arm/boot/dts/rk3229-evb.dt.yaml: spi-1:
'#address-cells' is a required property
arch/arm/boot/dts/rk3229-xms6.dt.yaml: spi-0:
'#address-cells' is a required property
arch/arm/boot/dts/rk3229-xms6.dt.yaml: spi-1:
'#address-cells' is a required property
The $nodename pattern for spi nodes is
"^spi(@.*|-[0-9a-f])*$". To prevent warnings rename
'spi-0' and 'spi-1' pinctrl sub nodenames to
'spi0' and 'spi1' in 'rk322x.dtsi'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/spi-controller.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200424123923.8192-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b14f3898d2 ]
Dts files with Rockchip 'gpu' nodes were manually verified.
In order to automate this process arm,mali-utgard.txt
has been converted to yaml. In the new setup dtbs_check with
arm,mali-utgard.yaml expects clock-names values
in the same order, so fix that.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200425192500.1808-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c604fd810b ]
Dts files with Rockchip rk3399 'gpu' nodes were manually verified.
In order to automate this process arm,mali-midgard.txt
has been converted to yaml. In the new setup dtbs_check with
arm,mali-midgard.yaml expects interrupts and interrupt-names values
in the same order. Fix this for rk3399.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/gpu/
arm,mali-midgard.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200425143837.18706-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c617ed8850 ]
The status was removed of the '&gmac2phy' node with the apply
of a patch long time ago, so fix status for '&gmac2phy'
in 'rk3328-evb.dts'.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200425122345.12902-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 621c8d0c23 ]
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3229-xms6.dt.yaml: phy@0:
'#phy-cells' is a required property
The phy nodename is normally used by a phy-handle.
This node is however compatible with
"ethernet-phy-id1234.d400", "ethernet-phy-ieee802.3-c22"
which is just been added to 'ethernet-phy.yaml'.
So change nodename to 'ethernet-phy' for which '#phy-cells'
is not a required property
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20200416170321.4216-2-jbx6244@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 287e0d538f ]
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3228-evb.dt.yaml: phy@0:
'#phy-cells' is a required property
The phy nodename is normally used by a phy-handle.
This node is however compatible with
"ethernet-phy-id1234.d400", "ethernet-phy-ieee802.3-c22"
which is just been added to 'ethernet-phy.yaml'.
So change nodename to 'ethernet-phy' for which '#phy-cells'
is not a required property
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20200416170321.4216-1-jbx6244@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 187b96db5c upstream.
Normally, show_trace_log_lvl() scans the stack, looking for text
addresses to print. In parallel, it unwinds the stack with
unwind_next_frame(). If the stack address matches the pointer returned
by unwind_get_return_address_ptr() for the current frame, the text
address is printed normally without a question mark. Otherwise it's
considered a breadcrumb (potentially from a previous call path) and it's
printed with a question mark to indicate that the address is unreliable
and typically can be ignored.
Since the following commit:
f1d9a2abff ("x86/unwind/orc: Don't skip the first frame for inactive tasks")
... for inactive tasks, show_trace_log_lvl() prints *only* unreliable
addresses (prepended with '?').
That happens because, for the first frame of an inactive task,
unwind_get_return_address_ptr() returns the wrong return address
pointer: one word *below* the task stack pointer. show_trace_log_lvl()
starts scanning at the stack pointer itself, so it never finds the first
'reliable' address, causing only guesses to being printed.
The first frame of an inactive task isn't a normal stack frame. It's
actually just an instance of 'struct inactive_task_frame' which is left
behind by __switch_to_asm(). Now that this inactive frame is actually
exposed to callers, fix unwind_get_return_address_ptr() to interpret it
properly.
Fixes: f1d9a2abff ("x86/unwind/orc: Don't skip the first frame for inactive tasks")
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200522135435.vbxs7umku5pyrdbk@treble
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70b690547d upstream.
initrd_start must not point at the location the initrd is loaded into
the crashkernel memory but at the location it will be after the
crashkernel memory is swapped with the memory at 0.
Fixes: ee337f5469 ("s390/kexec_file: Add crash support to image loader")
Reported-by: Lianbo Jiang <lijiang@redhat.com>
Signed-off-by: Philipp Rudo <prudo@linux.ibm.com>
Tested-by: Lianbo Jiang <lijiang@redhat.com>
Link: https://lore.kernel.org/r/20200512193956.15ae3f23@laptop2-ibm.local
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c1cbcbd6c upstream.
With certain kernel configurations, the R_390_JMP_SLOT relocation type
might be generated, which is not expected by the KASLR relocation code,
and the kernel stops with the message "Unknown relocation type".
This was found with a zfcpdump kernel config, where CONFIG_MODULES=n
and CONFIG_VFIO=n. In that case, symbol_get() is used on undefined
__weak symbols in virt/kvm/vfio.c, which results in the generation
of R_390_JMP_SLOT relocation types.
Fix this by handling R_390_JMP_SLOT similar to R_390_GLOB_DAT.
Fixes: 805bc0bc23 ("s390/kernel: build a relocatable kernel")
Cc: <stable@vger.kernel.org> # v5.2+
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f058599e22 upstream.
The s390_mmio_read/write syscalls are currently broken when running with
MIO.
The new pcistb_mio/pcstg_mio/pcilg_mio instructions are executed
similiarly to normal load/store instructions and do address translation
in the current address space. That means inside the kernel they are
aware of mappings into kernel address space while outside the kernel
they use user space mappings (usually created through mmap'ing a PCI
device file).
Now when existing user space applications use the s390_pci_mmio_write
and s390_pci_mmio_read syscalls, they pass I/O addresses that are mapped
into user space so as to be usable with the new instructions without
needing a syscall. Accessing these addresses with the old instructions
as done currently leads to a kernel panic.
Also, for such a user space mapping there may not exist an equivalent
kernel space mapping which means we can't just use the new instructions
in kernel space.
Instead of replicating user mappings in the kernel which then might
collide with other mappings, we can conceptually execute the new
instructions as if executed by the user space application using the
secondary address space. This even allows us to directly store to the
user pointer without the need for copy_to/from_user().
Cc: stable@vger.kernel.org
Fixes: 71ba41c9b1 ("s390/pci: provide support for MIO instructions")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8659a0e0ef ]
Several strange crashes have been eventually traced back to
STRICT_KERNEL_RWX and its interaction with code patching.
Various paths in our ftrace, kprobes and other patching code need to
be hardened against patching failures, otherwise we can end up running
with partially/incorrectly patched ftrace paths, kprobes or jump
labels, which can then cause strange crashes.
Although fixes for those are in development, they're not -rc material.
There also seem to be problems with the underlying strict RWX logic,
which needs further debugging.
So for now disable STRICT_KERNEL_RWX on 64-bit to prevent people from
enabling the option and tripping over the bugs.
Fixes: 1e0fc9d1eb ("powerpc/Kconfig: Enable STRICT_KERNEL_RWX for some configs")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200520133605.972649-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c55d7b5e64 ]
I have tested this with the Radix MMU and everything seems to work, and
the previous patch for Hash seems to fix everything too.
STRICT_KERNEL_RWX should still be disabled by default for now.
Please test STRICT_KERNEL_RWX + RELOCATABLE!
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191224064126.183670-2-ruscur@russell.cc
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1cf6022bd9 upstream.
Quoth the man page:
```
If the tracee was restarted by PTRACE_SYSCALL or PTRACE_SYSEMU, the
tracee enters syscall-enter-stop just prior to entering any system
call (which will not be executed if the restart was using
PTRACE_SYSEMU, regardless of any change made to registers at this
point or how the tracee is restarted after this stop).
```
The parenthetical comment is currently true on x86 and powerpc,
but not currently true on arm64. arm64 re-checks the _TIF_SYSCALL_EMU
flag after the syscall entry ptrace stop. However, at this point,
it reflects which method was used to re-start the syscall
at the entry stop, rather than the method that was used to reach it.
Fix that by recording the original flag before performing the ptrace
stop, bringing the behavior in line with documentation and x86/powerpc.
Fixes: f086f67485 ("arm64: ptrace: add support for syscall emulation")
Cc: <stable@vger.kernel.org> # 5.3.x-
Signed-off-by: Keno Fischer <keno@juliacomputing.com>
Acked-by: Will Deacon <will@kernel.org>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Bin Lu <Bin.Lu@arm.com>
[catalin.marinas@arm.com: moved 'flags' bit masking]
[catalin.marinas@arm.com: changed 'flags' type to unsigned long]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37486135d3 upstream.
Though rdpkru and wrpkru are contingent upon CR4.PKE, the PKRU
resource isn't. It can be read with XSAVE and written with XRSTOR.
So, if we don't set the guest PKRU value here(kvm_load_guest_xsave_state),
the guest can read the host value.
In case of kvm_load_host_xsave_state, guest with CR4.PKE clear could
potentially use XRSTOR to change the host PKRU value.
While at it, move pkru state save/restore to common code and the
host_pkru field to kvm_vcpu_arch. This will let SVM support protection keys.
Cc: stable@vger.kernel.org
Reported-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Babu Moger <babu.moger@amd.com>
Message-Id: <158932794619.44260.14508381096663848853.stgit@naples-babu.amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paolo Bonzini